2012 Dodge Dart TSBs

replacement due to damage OR not fully illuminated IP center bezel. Thank you.

The customer and or dealer may note that the remote start option is missing from the vehicle. The Monroney label will shows the vehicle having this feature.

and/or rear seat backs, seat cushions and/or headrests. The vehicle has been shipped with the incorrect interior seat covers and/or headrests.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

and/or rear seat backs, seat cushions and/or headrests. The vehicle has been shipped with the incorrect interior seat covers and/or headrests.

MODEL 2013 DART. *PE

Some customers may experience any of the following conditions: ? Engine starts then immediately stalls when using Remote Start system (Instrument Cluster may display the message ?Remote Start Disabled, Start Vehicle to Reset?). ? Engine cranks and does not start following the condition described above. ? Engine may be hard to re-start at ambient temps below -12C (10F). NOTE: The Powertrain Control Module (PCM) and Transmission Control Module (TCM) must be up to date for these changes to be effective.

the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has been set in the PCM memory: ? P0456 - Evap System Small Leak. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P1D73 - AGS Performance - (Active Grille Shutters). ? P1607 - PCM Internal Shutdown Timer Rationality - (Powertrain Control Module). ? P2610 - PCM Internal Engine Off Timer Performance - (Powertrain Control Module). ? U0140 - Lost Communication With Body Control Module. ? P0335 - Crankshaft Position Sensor Circuit. ? P000B - Exhaust Slow Response Bank 1. ? P050B - Cold Start Ignition Timing Performance. ? P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). In addition this software release includes improving the disable misfire monitor when P0335 (Crankshaft Position Sensor Circuit) is present.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8) ? P0133 - O2 Sensor 1/1 Slow Response. ? P0456 - Evap System Small Leak. ? Low Idle Speed After Cold Start between 14F to 32F (-10C to 0C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10F to 40F (-12C to 4.5C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles (Sales Codes ED6)

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8). ? Improved vehicle acceleration. ? P0480 - Cooling Fan 1 Control Circuit/Open. ? P0456 - Evap System Small Leak. ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8), built on or before July 24, 2015 (MDH 0724XX). ? Low Idle Speed After Cold Start between 14F to 32F (-10C to 0C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10F to 40F (-12C to 4.5C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detec

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTCs) have been set: ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream ? P1D73 - 00 - AGS Performance ? P1CEA - Boost Side Evap Purge System Performance ? P0456 - Evap System Small Leak Customers may also experience any of the following symptoms: ? Customer experiences cold start issues below 14F ( -10C) ambient temperatures; engine turns over faster (loss of compression) during crank and possibly does not start until a key cycle is performed. ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? Spark knock when using low octane fuel in the vehicle. ? Black smoke from tail pipe on initial start up during cold ambient temperatures. ? Uneven acceleration feeling under moderate to heavy throttle input. ? Bump or surge noticed prior to engine reaching normal operating temperature. ? Rough idle during A/C engagement/disengagement. ? During periods of extended idle or short hot soak events and ambient temperatures below 15F (-9C), engine idle speed may increase to 1800 RPM if coolant temperature drops below 158F (70C). Condition is only present when the transmission is in park. ? Low speed engine response improvements in city and traffic driving conditions. Updating the PCM software will correct the condition listed above.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. In addition, some customers may describe engine flare at startup or idle surge. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (sales codes ED6, ED8), built on or before June 16th, 2015 (MDH 0615XX). ? U0402 - Implausible Data Received From TCM (ED6, ED8). ? Engine Startup Flare and Idle Surge (ED6, ED8). ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance (sales codes ED6, ED8). ? P0116 - Engine Coolant Temperature Sensor 1 Performance (sales codes ED6, ED8). ? P050D - Cold Start Rough Idle (sales codes ED6, ED8). 2015 PF Vehicles with (sales codes ED6, ED8), built on or before April 2nd, 2015 (MDH 0402XX). ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10F to 40F (-12C to 4.5C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance (sales codes ED6, ED8). ? P050B - Cold Start Ignition Timing Performance (sales codes ED6, ED8). ? P050D - Cold Start Rough Idle (sales codes ED6, ED8). ? P061A - Level 2 Torque Performance (sales codes ED6, ED8). ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation) (sales codes ED6, ED8). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off T

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (sales codes ED6 or ED8), built on or before April 6, 2015 (MDH 0406XX). ? Improve cold engine idle, reduce idle flare up (ED6 only). ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance . ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (sales codes ED6, ED8), built on or before April 2, 2015 (MDH 0402XX). ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10F to 40F (-12C to 4.5C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P1128 - Closed Loop Fueling Not Achieved - Bank 1 Upstream. ? P1D73-00-AGS Performance. ? P1CEA- Boost Side Evap Purge System Performance. ? P0456- Evap System Small Leak. Customers may also experience any of the following symptoms: ? Engine cranks as if it has no compression. ? Engine sounds like it is knocking at idle, noise goes away when off idle. ? Spark knock when using low octane fuel in the vehicle. ? Black smoke from tail pipe on initial start up during cold ambient temperatures. ? Uneven acceleration feeling under moderate to heavy throttle input. ? Bump or surge noticed prior to engine reaching normal operating temperature. ? Rough idle during A/C engagement/disengagement. ? During periods of extended idle or short hot soak events and ambient temperatures below 15F (-9C), engine idle speed may increase to 1800 RPM if coolant temperature drops below 158F (70C). Condition is only present when the transmission is in park. ? Low speed engine response improvements in city and traffic driving conditions. Updating the PCM software will correct the condition listed above.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8), built on or before June 16, 2015 (MDH 0616XX). ? U0402 - Implausible Data Received From TCM. ? Engine Startup Flare and Idle Surge. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0441 - Evap Purge System Performance. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050D - Cold Start Rough Idle. 2015 PF Vehicles with (Sales Codes ED6, ED8), built on or before July 24, 2015 (MDH 0724XX). ? Low Idle Speed After Cold Start between 14F to 32F (-10C to 0C). ? Cold Idle Surge With AC Engaged. ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10F to 40F (-12C to 4.5C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. ? P0116 - Engine Coolant Temperature Sensor 1 Performance. ? P050B - Cold Start Ignition Timing Performance. ? P050D - Cold Start Rough Idle. ? P061A - Level 2 Torque Performance. ? P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Bod

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. 2015 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. 2015 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles, built on or before October 21, 2014 (MDH 1021XX). ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. 2015 PF Vehicles, built on or before January 08, 2015 (MDH 0108XX). ? Improve cabin warm up in cold weather, when the vehicle is in park or neutral and the temperature is between 10F to 40F (-12C to 4.5C). ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module. 2013-2014 PF Vehicles. ? P219A - Bank 1 Air-Fuel Ratio Imbalance. ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. ? P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. ? P2172 - High Airflow/Vacuum Leak Detected. ? P1D73 - AGS Performance. ? U0140 - Lost Communication With Body Control Module.

selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P1D73-00-AGS Performance ? P1CEA- Boost Side Evap Purge System Performance ? P0456- Evap System Small Leak Customers may also experience any of the following symptoms: ? Spark knock when using low octane fuel in the vehicle. ? Black smoke from tail pipe on initial start up during cold ambient temperatures. ? Uneven acceleration feeling under moderate to heavy throttle input ? Bump or surge noticed prior to engine reaching normal operating temperature ? Rough idle during A/C engagement/disengagement ? During periods of extended idle or short hot soak events and ambient temperatures below 15F(-9C), engine idle speed may increase to 1800 RPM if coolant temperature drops below 158F(70C). Condition is only present when the transmission is in Park. ? Low speed engine response improvements in city and traffic driving conditions Updating the PCM software will correct the condition listed above.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) **P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak.** P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0116 - Engine Coolant Temperature Sensor 1 Performance. P050B - Cold Start Ignition Timing Performance. P061A - Level 2 Torque Performance. P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: Low Idle Speed After Cold Start between -10C to 0C (14F to 32F). Cold Idle Surge With AC Engaged.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) **P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range.** U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. P1185 - General Pressure Sensor Correlation. P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0116 - Engine Coolant Temperature Sensor 1 Performance. P050B - Cold Start Ignition T

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. P1185 - General Pressure Sensor Correlation. P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0116 - Engine Coolant Temperature Sensor 1 Performance. P050B - Cold Start Ignition Timing Performance. P061A - Level 2 Torque Performance. P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: Low Idle Speed After Cold Start between -10C to 0C (14F to 32F). Cold Idle Surge With AC Engaged

Please do not order this part as a shotage and error on this model (unless it is customer pay).

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

(PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs set in the PCM memory: U1504 - Implausible Message Data Length Received From Steering Angle Sensor. P0128 - Thermostat Rationality. P0335 - Crankshaft Position Sensor Circuit. P0340 - Camshaft Position Sensor Circuit Bank 1 Sensor 1. U1424-00 - Implausible Engine Torque Signal Received. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance.In addition to the DTCs above the following improvements have been made: Min spark changes to prevent catalytic converter overheating. Engine Startup Flare and Idle Surge. Improved vehicle acceleration. P1066 - Cylinder 1 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P1068 - Cylinder 2 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. P106C - Cylinder 4 Oil Supply Solenoid Valve Switch Off Time Out Of Range. U0401 - Implausible Data Received From ECM/PCM - Signal Invalid.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: 2015 UF Vehicles with (Sales Codes ED6, ED8) P050D - Cold Start Rough Idle. P0335 - Crankshaft Position Sensor Circuit. P1607 - PCM Internal Shutdown Timer Rationality. P0133 - O2 Sensor 1/1 Slow Response. P0456 - EVAP System Small Leak. P0480 - Cooling Fan 1 Control Circuit/Open. U0402 - Implausible Data Received From TCM. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0441 - Evap Purge System Performance. P0116 - Engine Coolant Temperature Sensor 1 Performance. In addition to the DTCs above the following improvements have been made: Engine Startup Flare and Idle Surge. Improved vehicle acceleration. 2015 PF Vehicles with (Sales Codes ED6, ED8) **U0401 - Implausible Data Received From ECM/PCM - Signal Invalid. P1185 - General Pressure Sensor Correlation.** P050D - Cold Start Rough Idle. P0133 - O2 Sensor 1/1 Slow Response. P0456 - Evap System Small Leak. P219A - Bank 1 Air-Fuel Ratio Imbalance. P2172 - High Airflow/Vacuum Leak Detected. P1D73 - AGS Performance. U0140 - Lost Communication With Body Control Module. P0116 - Engine Coolant Temperature Sensor 1 Performance. P050B - Cold Start Ignition Timing Performance. P061A - Level 2 Torque Performance. P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation). In addition to the DTCs above the following improvements have been made: Low Idle Speed After Cold Start between -10C to 0C (14F to 32F). Cold Idle Surge With AC Eng

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

Please do not order this part as a shotage and error on this model (unless it is customer pay).

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

Also Includes Various Driveability Enhancements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) and Transmission Control Module (TCM) with new software.Both the PCM and TCM must be up to date for these changes to be effective. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0456 - Evap System Small LeakCustomers may also experience any of the following conditions: (Applies only to Automatic Transmission) Engine may be difficult to start and/or re-start when operating in temperatures below 32F(0C)Driveability and Transmission Enhancements are also included with this software release. These changes include the following: (Applies only to Automatic Transmission) Improved evap purge strategy under high ambient temperatures Improved engine oil pressure sensor accuracyUpdating the PCM and TCM software will correct the conditions listed above.

2013 model year (PF) Dodge Dart vehicles equipped with a 1.4L Multi-Air turbocharged engine. Some of the above vehicles may experience an engine stall when the engine is first started while the outside ambient air temperature is 20 degrees or lower and the vehicle is operated under certain driving conditions. Chrysler will conduct a voluntary safety recall on all involved vehicles to reprogram the Powertrain Control Module (PCM) with new software. Dealers will be notified of the launch of this safety recall by way of established methods used in the past. We ask that you please take the time to ensure that your personnel are aware of this communication and are prepared to execute a customer friendly process for inquiries on involved vehicles.

the Powertrain Control Module (PCM) with new software and updating the Body Control Module (BCM) software. A small number of customers may experience any of the following conditions: Engine starts then immediately stalls when using Remote Start system (Instrument Cluster may display the message ?Remote Start Disabled, Start Vehicle to Reset?) Engine cranks and does not start following the condition described above Engine may be hard to re-start at ambient temps below 10F(-12C)Updating the software will correct the conditions listed above.

the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: ? Engine starts then immediately stalls when using Remote Start system (Instrument Cluster may display the message ?Remote Start Disabled, Start Vehicle to Reset?) ? Engine cranks and does not start following the condition described above ? Engine may be hard to re-start at ambient temps below 10F(-12C) Updating the software will correct the conditions listed above.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

contact FCA engineering if ANY of the following Diagnostic trouble codes are Stored or Active in the ORC module:~ DTC: B223D-00 - OCM DTC Present~ DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open~ DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open~ DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open~ DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open~ DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open~ DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open~ Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent, corroded, or spread conditions. If no response within 15 minutes, proceed with repair.~ FCA Engineering Contacts:~ Jay Nagle (ORC Module, Driver/passenger seat track position sensor for PF, KL or UF Vehicles ONLY) @ cell (248) 420-4294 or jay.nagle@external.fcagroup.com~ Malcolm Whitehouse (OCM Module - PF,KL, or UF Vehicles ONLY)@248-462-4703 or Malcolm.Whitehouse@fcagroup.com.~ Bill Winfrey (Driver/Passenger Buckle Switch, Passenger/Driver Seat Thorax Airbags) @ cell (248) 941-9221 or william.winfrey@fcagroup.com~

the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: ? Engine starts then immediately stalls when using Remote Start system (Instrument Cluster may display the message ?Remote Start Disabled, Start Vehicle to Reset?) ? Engine cranks and does not start following the condition described above ? Engine may be hard to re-start at ambient temps below 10F(-12C) Updating the software will correct the conditions listed above.

Please do not order this part as a shotage and error on this model (unless it is customer pay).

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

Some customers may experience a reduction in clutch pedal stroke.

A) To announce an extended warranty on the Hydraulic Clutch Master Cylinder/ Reservoir Hose on the following vehicles: ? 2013-2015 Dodge Dart (PF) ? 2014-2015 Jeep Cherokee (KL)

Some customers may experience a reduction in clutch pedal stroke.

BULLETIN INVOLVES REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) WITH THE LATEST AVAILABLE SOFTWARE. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION OR ONE OR MORE OF THE FOLLOWING CONDITIONS. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS) SET IN THE PCM, MEMORY:2015 UF VEHICLES WITH (SALES CODES ED6, ED8) P050D - COLD START ROUGH IDLE. P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. P1607 - PCM INTERNAL SHUTDOWN TIMER RATIONALITY. P0133 - O2 SENSOR 1/1 SLOW RESPONSE. P0456 - EVAP SYSTEM SMALL LEAK. P0480 - COOLING FAN 1 CONTROL CIRCUIT/OPEN. U0402 - IMPLAUSIBLE DATA RECEIVED FROM TCM. P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED.P1D73 - AGS PERFORMANCE. U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE. P0441 - EVAP PURGE SYSTEM PERFORMANCE. P0116 - ENGINE COOLANT TEMPERATURE SENSOR 1 PERFORMANCE.IN ADDITION TO THE DTCS ABOVE THE FOLLOWING IMPROVEMENTS HAVE BEEN MADE:ENGINE STARTUP FLARE AND IDLE SURGE.IMPROVED VEHICLE ACCELERATION. 2015 PF VEHICLES WITH (SALES CODES ED6, ED8)U0401 - IMPLAUSIBLE DATA RECEIVED FROM ECM/PCM - SIGNAL INVALID. P1185 - GENERAL PRESSURE SENSOR CORRELATION.P050D - COLD START ROUGH IDLE. P0133 - O2 SENSOR 1/1 SLOW RESPONSE. P0456 - EVAP SYSTEM SMALL LEAK.P219A - BANK 1 AIR-FUEL RATIO IMBALANCE. P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED.P1D73 - AGS PERFORMANCE.U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE. P0116 - ENGINE COOLANT TEMPERATURE SENSOR 1 PERFORMANCE. P050B - COLD START IGNITION TIMING PERFORMANCE. P061A - LEVEL 2 TORQUE PERFORMANCE.P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED (INSTANTANEOUS ACCUMULATION).IN ADDITION TO THE DTCS ABOVE THE FOLLOWING IMPROVEMENTS HAVE BEEN MADE: LOW IDLE SPEED AFTER COLD START BETWEEN -10C TO 0C (14F TO 32F).

ALSO THE ENGINE MAY CRANK AS IF IT HAS NO COMPRESSION, ENGINE KNOCKING SOUNDS AT IDLE AND WHEN USING LOW OCTANE FUEL SPARK KNOCK IS PRESENT. *CN

(DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE

TO BE UNDETECTED, RESULTING IN EXCESSIVE EXHAUST EMISSIONS. MODEL 2013 DART. *PE

RESTART IN TEMPERATURE BELOW 32%F (0%C) AND MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. MODEL 2013 DART. *PE

A METALLIC NOISE/RATTLE UNDER CERTAIN DRIVING CONDITIONS IS DUE TO LOOSE ENGINE TORQUE ROD BOLT, AT TIME OF MANUFACTURING, THAT MAY NOT HAVE BEEN PROPERLY TIGHTENED. MODEL 2013 DART. *PE

ENGINE MAY CRANK BUT WILL NOT START. ENGINE MAY BE DIFFICULT TO RESTART AT AMBIENT TEMPS. SOFTWARE UPDATE IS NEEDED TO CORRECT THIS PROBLEM. *KB

SOME VEHICLES MAY HAD TRANSAXLE CLUTCH SLAVE CYLINDER IMPROPERLY MANUFACTURED AND THIS CAN CAUSE HYDRAULIC FLUID TO LEAK AT TRANSAXLE CLUTCH SLAVE CYLINDER. MODEL 2013 DART. *PE

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.

Premium Tire Pressure Monitor System (TPMS). The customer may notice a message ?Low Tire? displayed on the cluster: ? Tire Pressure Monitoring screen on the instrument cluster may indicate the incorrect tire location shown when low tire pressure is detected. ? Example scenario: Right rear tire (RR) may show as low on the instrument cluster when actually it may be left front tire (LF) as being low when a tire gauge is used to check tire pressure. Fig. 1 Low Tire Display On Instrument Cluster

A

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory. * P2172 - High Airflow/Vacuum Leak Detected * P1D73 - AGS Performance * U0140 - Lost Communication With Body Control Module

software.Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: U11F6-00 Lost Communication With Convergence Telematics Module. U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.

NOTE: Convergence Telematics Module (CTM) was also known as the Hands Free Module (HFM). The customer may notice that the hand free feature (Bluetooth) does not work. On further inspection one or more of the following DTCs may be found: ? U11F6-00 Lost Communication With Convergence Telematics Module. ? U11F6-87 Lost Communication With Convergence Telematics Module - Missing Message.

electrical harness connector is properly connected.

The customer may notice a ?Service Battery? message is displayed in the Electronic Vehicle Information Center (EVIC). This message is most likely to be displayed when the outside temperatures are colder. On further inspection no DTC?s will be found.

The customer may notice a ?Service Battery? message is displayed in the Electronic Vehicle Information Center (EVIC). This message is most likely to be displayed when the outside temperatures are colder. On further inspection no DTC?s will be found.

erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes (DTC?s) have been set: ? P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open

A customer may experience, no response or slow response to cruise control switch activations. Issues will be experienced by the customers that activate/press the switches in a very fast manner.

Hub Module (RFHM) The customer may experience one or both of the following conditions. Remote Keyless Entry (RKE) will not unlock the doors. Pass entry feature will not operate, If equipped. On further inspection there should be no DTC set for this issue.

secured to the decklid assembly after disclosing promotional pricing the customer will be responsible for. The customer received a promotional flyer and/or is aware of the promotional pricing for a new center rear lamp that is equipped with the racetrack lighting function for all models except SE.

This bulletin involves updating the software in the Radio Frequency Hub Module (RFHM) The customer may experience one or both of the following conditions. ? Remote Keyless Entry (RKE) will not unlock the doors. ? Pass entry feature will not operate, If equipped.

secured to the decklid assembly after disclosing promotional pricing the customer will be responsible for. The customer received a promotional flyer and/or is aware of the promotional pricing for a new center rear lamp that is equipped with the racetrack lighting function for all models except SE.

The customer may experience one or more of the following conditions. Radio switches to USB with no input from the driver. Radio display jitters sometimes while displaying the caller ID. Radio preset does not work while in browse mode. Radio turns on unexpectedly when a phone reconnects after an ignition cycle. Rapid press of preset buttons does not advance to the next bank of presets. Shuffle repeat icon are displayed while the radio is off. When giving the Voice Recognition (VR) command "Radio", the radio does not switch back to last known radio mode. Radio displays shows MW instead of AM (export radio only).

The customer received a promotional flyer and/or is aware of the promotional pricing for a new center rear lamp that is equipped with the racetrack lighting function for all models except SE.

POWER CONTROL MODULE REQUIRES REPROGRAMMING WITH LATEST SOFTWARE AVAILABLE *CN UPDATED 12/21/15 *CN

SELECTIVE ERASING AND REPROGRAMMING OF POWERTRAIN CONTROL MODULE (PCM) NEW SOFTWARE. MODELS 2013 DART. *PE

*KB

The customer may describe a front brake squeak/squeal high frequency noise in the 6-7 kHz range while stopping, noise may be intermittent (not every stop).

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

The customer may experience a squealing noise during braking coming from the front of the vehicle.

brackets, spring clips and if necessary front brake pads. Rattle from front brakes when driving, without brakes applied

brackets, spring clips and if necessary front brake pads. Rattle from front brakes when driving, without brakes applied

MODELS 2013 DART. *PE

A customer may experience one or more of the following conditions: ? Radio display screen will lock up and reset intermittently (2013-2014 MY Vehicles). ? Navigation screen goes blank (Software has been updated to better address this condition). ? Navigation system freezes/locks up (Software has been updated to better address this condition). ? Vehicles with Mopar special edition radio, update radio?s splash screen. (2013 Vehicles). ? Incorrect routing directions to fuel stations when using Travel Link. ? Unable to turn on heated seats, icon is greyed out. ? Navigation Icon shows the vehicle going backward when it is moving forward. ? Map Checksum error may be displayed when attempting to update the navigation system maps.

A customer may experience, one or more of the following conditions: ? Incorrect routing directions to fuel stations when using Travel Link. ? Unable to turn on heated seats. Icon is greyed out. ? Radio display screen will lock up and reset intermittently. ? Navigation screen goes blank. ? Navigation system freezes/locks up. ? Navigation Icon shows the vehicle going backward when it is moving forward. ? Map Checksum error may be displayed when attempting to update the navigation system maps.

A customer may experience, one or more of the following conditions: ? Incorrect routing directions to fuel stations when using Travel Link. ? Unable to turn on heated seats. Icon is greyed out. ? Radio display screen will lock up and reset intermittently. ? Navigation screen goes blank. ? Navigation system freezes/locks up. ? Navigation Icon shows the vehicle going backward when it is moving forward. ? Map Checksum error may be displayed when attempting to update the navigation system maps.

and if necessary modifying the fuel filler housing. It may also involve inspecting the fuel filler door and if necessary reinstalling or replacing the fuel filler housing. Rattle and/or buzz at the right rear of vehicle and/or fuel door difficult to open.

Module (TCM) with the latest available software. Customers may experience any of the following symptoms: ? Transmission shift improvements when using cruise control. ? Improved garage shift feel and quality. NOTE: The Body Control Module (BCM) and Powertrain Control Module (PCM) must be up to date for these changes to be effective.

Attempts to flash with the ignition in the run position may result in flash failures

symptom/condition and if necessary, replacing the rear suspension springs. Right side rear suspension spring is shifted in the upper spring mount isolator and possibly a clunk noise can be heard or felt coming from the rear of the vehicle, while going over bumps.

Nut, make sure to torque to proper spec of 150 ft/lbs (200 Nm) and crimp according to procedure in TechConnect. (This torrque is higher than other platforms). Failure to do so will result in eventual Hub & Bearing failure (noise).~

Clicking and/or crunching noise from rear springs.

Clicking and/or crunching noise from rear springs.

Customer may describe a creak or squeak noise while turning the steering wheel. Noise is typically more noticeable during cold temperatures below 4C (40F), noise may go away when temperature warms up.

software in the Electric Power Steering (EPS). If required road force balancing and match mounting the tires and wheels. NOT be mistaken for a normal tire vibration felt in the seat and steering wheel or at low speeds.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

CUSTOMERS MAY NOTICE A "LOW TIRE" MESSAGE ON THE CLUSTER. *LJ

UPDATING THE SOFTWARE SHOULD CORRECT KEYLESS ENTRY ISSUE. *KB