2014 Dodge Charger TSBs

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles e

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

(PCM) with the latest available software. A small number of customers may experience one or more of the following conditions: With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 kph when pressing the buttons, the vehicle speed will increase approximately 1.6 kph. Potential gear hunting during cruise operation at lower vehicle speeds 40-64 kph (25-40 mph). In addition, a small number of customers may experience certain symptoms/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes have been set: **P1115 - General Temperature Rationality. P0456 - EVAP System Small Leak. P0441 - EVAP Purge System Performance. P2610 - PCM Internal Engine Off Timer Performance. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P0307 - Cylinder 7 Misfire. P0308 - Cylinder 8 Misfire. P0335 - Crankshaft Position Sensor Circuit. P0122 - Throttle Position Sensor 1 Circuit Low. P0123 - Throttle Position Sensor 1 Circuit High. P0222 - Throttle Position Sensor 2 Circuit Low. P0223 - Throttle Position Sensor 2 Circuit High. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible.** P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC).

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

exhaust system (resonator and muffler right hand assembly) cracks at or around the weld near the muffler with Model Year '13, '14, '16, and '17 Charger and Challenger 5.7L. Please call Design Release Engineer Jeff Robinson at cell phone (315) 408-6055 and send a photo of the part to him at Jeff.Robinson@fcagroup.com. If no response in 15 minutes, please proceed with repair.

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A for an exchange or 05064993A for a new part replacement. Prior to replacing parts, Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Reggie Phillips at cell (678) 330-0255. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~ ~______________________________________~ Contact Us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. DO NOT email regarding repair procedures unrelated to this Tech Tip or part order inquires. Please include the Part Number (s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. (Sales Code ERB). (LD, LX vehicles only). P0606 - Internal Control Processor.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB)

Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

If the pins are missing request to add the dowel pin first and then install the transmission

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

(PCM) with the latest available software. A small number of customers may experience one or more of the following conditions: With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 kph when pressing the buttons, the vehicle speed will increase approximately 1.6 kph. Potential gear hunting during cruise operation at lower vehicle speeds 40-64 kph (25-40 mph). In addition, a small number of customers may experience certain symptoms/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes have been set: **P1115 - General Temperature Rationality. P0456 - EVAP System Small Leak. P0441 - EVAP Purge System Performance. P2610 - PCM Internal Engine Off Timer Performance. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P0307 - Cylinder 7 Misfire. P0308 - Cylinder 8 Misfire. P0335 - Crankshaft Position Sensor Circuit. P0122 - Throttle Position Sensor 1 Circuit Low. P0123 - Throttle Position Sensor 1 Circuit High. P0222 - Throttle Position Sensor 2 Circuit Low. P0223 - Throttle Position Sensor 2 Circuit High. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible.** P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC).

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak (Sales Code ERB).** U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). P0606 - Internal Control Processor.

Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Engine Poor powertrain response or performance when trying to accelerate from moderate vehicle speed in HOT ambient temperature conditions. Short shifting or surging during near to WOT accelerations with mild ambient temperature conditions . Transmission does not maintain vehicle set speed when cruise control is active and vehicle is traveling down steep grades. Hanging in gear complaints during HOT ambient temperature condition or when aggressively driving and WOT throttle is requested.5.7L Engine Hanging in gear complaints during HOT ambient temperature condition or when aggressively driving and WOT throttle is requested.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

Module with the latest available software. A small number of customers may experience one or more of the following conditions: ? With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. ? Potential gear hunting during cruise operation at lower vehicle speeds (25-40 mph). In addition, a small number of customers with manual transmission equipped vehicles may experience certain symptoms/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: ? P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2098 - Downstream Fuel Trim System 2 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2099 - Downstream Fuel Trim System 2 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P0300 - Multiple Cylinder Misfire (set during engine warm-up) (LC vehicles with Sales Code ESH with a manual transmission [Sales Code DEC]).

power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 2.; During a Travel Link software update.....The radio locks up and displays "Software Missing" with a green screen. Please contact Nabil Issa at cell (248) 941- 8720 or Reggie Philip at cell (678) 330-0255. IMPORTANT - Do not clear codes, perform a battery reset, or remove the radio before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. ~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Gaurav Saxena at cell (248) 260-0583. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.

Module with the latest available software. A small number of customers may experience one or more of the following conditions: ? With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. ? Potential gear hunting during cruise operation at lower vehicle speeds (25-40 mph). In addition, a small number of customers with manual transmission equipped vehicles may experience certain symptoms/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: ? P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2098 - Downstream Fuel Trim System 2 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2099 - Downstream Fuel Trim System 2 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P0300 - Multiple Cylinder Misfire (set during engine warm-up) (LC vehicles with Sales Code ESH with a manual transmission [Sales Code DEC]).

power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 2.; During a Travel Link software update.....The radio locks up and displays "Software Missing" with a green screen. Please contact Nabil Issa at cell (248) 941- 8720 or Reggie Philip at cell (678) 330-0255. IMPORTANT - Do not clear codes, perform a battery reset, or remove the radio before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. ~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Gaurav Saxena at cell (248) 260-0583. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

If the pins are missing request to add the dowel pin first and then install the transmission

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Engineering is looking to gather infomation on fail mode and customer concern. If no response in 15 minutes, proceed with repair.

power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 2.; During a Travel Link software update.....The radio locks up and displays "Software Missing" with a green screen. Please contact Nabil Issa at cell (248) 941-8720 or Dave Clemons at cell (248) 520-0419. IMPORTANT - Do not clear codes, perform a battery reset, or remove the radio before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. ~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Gaurav Saxena at cell (248) 260-0583 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~

Module (PCM) with the latest available software. A small number of customers may experience one or more of the following symptoms or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the Powertrain Control Module (PCM): ? U0140 - Lost Communication With Body Control Module (LD and LX). ? U0140 - Lost Communication With Body Control Module (TIPM) stored in the Engine Control Module (ECM) memory (LC vehicles). ? P1621 - O2 Sensor Reference Voltage Circuit Low. ? P1622 - O2 Sensor Reference Voltage Circuit High. ? P0606 - Internal Control Processor. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1. ? P0300 - Multiple Cylinder Misfire (applies only to vehicles using a block heater in ambient temperatures greater than -20F (-29C). ? Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information (LC vehicles). ? Accuracy improvements for the Automatic Oil Change Indicator (AOCI) system.

Module with the latest available software. A small number of customers may experience one or more of the following conditions: ? With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. ? Potential gear hunting during cruise operation at lower vehicle speeds (25-40 mph). In addition, a small number of customers with manual transmission equipped vehicles may experience certain symptoms/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: ? P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2098 - Downstream Fuel Trim System 2 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P2099 - Downstream Fuel Trim System 2 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). ? P0300 - Multiple Cylinder Misfire (set during engine warm-up) (LC vehicles with Sales Code ESH with a manual transmission [Sales Code DEC]).

power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 2.; During a Travel Link software update.....The radio locks up and displays "Software Missing" with a green screen. Please contact Nabil Issa at cell (248) 941- 8720 or Reggie Philip at cell (678) 330-0255. IMPORTANT - Do not clear codes, perform a battery reset, or remove the radio before calling. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. ~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Gaurav Saxena at cell (248) 260-0583. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.

Module (PCM) with the latest available software. A small number of customers may experience one or more of the following symptoms or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more Dagnostic Trouble Codes (DTCs). ? DTC: U0140 - Lost Communication With Body Control Module (TIPM) stored in the Engine Control Module (ECM) memory (applies only to LC vehicles). ? DTC: P1621 - O2 Sensor Reference Voltage Circuit Low ? DTC: P1622 - O2 Sensor Reference Voltage Circuit High ? DTC: P0606 - Internal Control Processor ? DTC: P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 ? P0300 - Multiple Cylinder Misfire (applies only to vehicles using a block heater in ambient temperatures greater than -20F (-29C)) ? Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information (applies only to LC vehicles). ? Accuracy improvements for the Automatic Oil Change Indicator (AOCI) system.

Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ) and are broken down per engine application. 3.6L Engine (LD/LX) ? Erratic shifting or poor performance complaints while driving up steep hills, towing, driving aggressively, or at high altitude during hot ambient temperatures. ? Poor performance when driving aggressively. ? Poor powertrain response or performance when trying to accelerate from moderate vehicle speed in HOT ambient temperature conditions. ? Short shifting or surging during near to WOT accelerations with mild ambient temperature conditions. ? Transmission does not maintain vehicle set speed when cruise control is active and vehicle is traveling down steep grades. ? Hanging in gear complaints during HOT ambient temperature condition or when aggressively driving and WOT throttle is requested. 3.6L Engine (LD Police) ? Erratic shifting or poor performance complaints while driving up steep hills, or at high altitude during hot ambient temperatures. ? Poor performance when driving aggressively. 5.7L Engine (LD/LX) ? Erratic shifting or poor performance complaints while driving up steep hills, towing, driving aggressively, or at high altitude during hot ambient temperatures. ? Poor shift quality (bump or torque disturbance) when coasting to a stop. ? Poor city fuel economy (AWD Only). Hanging in gear complaints during HOT ambient temperature condition or when aggressively driving and WOT throttle is requested. 5.7L Engine (LD Daytona) Erratic shifting or poor performance complaints while driving up steep hills, towing, driving aggressively, or at high altitude during hot ambient temperatures. Poor shift quality (bump or torque disturbance) when coasting to a stop

Module with the latest available software. A small number of customers may experience one or more of the following conditions. ? With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. ? Potential gear hunting during cruise operation at lower vehicle speeds (25-40mph). ? The generator indicator light may be illuminated on the instrument cluster even though the generator is properly charging. In addition, a small number of customers with manual transmission equipped vehicles, may experience certain symptom/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code has been set: ? P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with sales code ESH with a manual transmission (sales code DEC). ? P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with sales code ESH with a manual transmission (sales code DEC). ? P2098 - Downstream Fuel Trim System 2 Lean. (LC vehicles with sales code ESH with a manual transmission (sales code DEC). ? P2099 - Downstream Fuel Trim System 2 Rich. (LC vehicles with sales code ESH with a manual transmission (sales code DEC). ? P0300 - Multiple Cylinder Misfire (set during engine warm-up) (LC vehicles with sales code ESH with a manual transmission (sales code DEC).

with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine. LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to enable the scan tool based transmission ?Quick Learn.? ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) ? Software to correct a harsh bump feel during a 2-1 downshift. WK vehicles equipped with a 3.6L engine (Sales Code ERB) ? ECO mode will not retain settings. If ECO mode is turned off, it will turn back on after the ignition is cycled. ? Software to correct a harsh bump feel during a 2-1 downshift. DS vehicles equipped with 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to address a customer?s concern of less than desired shift quality in Four Wheel Drive (4wd) Low mode during medium to heavy acceleration. ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. ? Software improvements to powertrain braking in Tow/Haul mode. ? Software to improve downshift response from a medium to heavy pedal acceleration. ? Driveability improvements at higher altitudes. ? Software to improve acceleration during cruise control operation ? Software to correct a condition where DTC U11C3 - ESM Lost Communication With TCM On D-Pt CAN may have been displayed inste

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio. ~

Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Engine Poor powertrain response or performance when trying to accelerate from moderate vehicle speed in HOT ambient temperature conditions. Short shifting or surging during near to WOT accelerations with mild ambient temperature conditions . Transmission does not maintain vehicle set speed when cruise control is active and vehicle is traveling down steep grades. Hanging in gear complaints during HOT ambient temperature condition or when aggressively driving and WOT throttle is requested.5.7L Engine Hanging in gear complaints during HOT ambient temperature condition or when aggressively driving and WOT throttle is requested.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

(PCM) with the latest available software. A small number of customers may experience one or more of the following conditions: With the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 kph when pressing the buttons, the vehicle speed will increase approximately 1.6 kph. Potential gear hunting during cruise operation at lower vehicle speeds 40-64 kph (25-40 mph). In addition, a small number of customers may experience certain symptoms/conditions or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes have been set: P1115 - General Temperature Rationality. P0456 - EVAP System Small Leak. P0441 - EVAP Purge System Performance. P2610 - PCM Internal Engine Off Timer Performance. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P0307 - Cylinder 7 Misfire. P0308 - Cylinder 8 Misfire. P0335 - Crankshaft Position Sensor Circuit. P0122 - Throttle Position Sensor 1 Circuit Low. P0123 - Throttle Position Sensor 1 Circuit High. P0222 - Throttle Position Sensor 2 Circuit Low. P0223 - Throttle Position Sensor 2 Circuit High. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible.** P2096 - Downstream Fuel Trim System 1 Lean. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). P2097 - Downstream Fuel Trim System 1 Rich. (LC vehicles with Sales Code ESH with a manual transmission (Sales Code DEC). P2098 - Downstream Fuel Trim System 2 Lean. (LC vehicles with Sales Code ESH with a ma

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3.; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine.LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to enable the scan tool based transmission ?Quick Learn.? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) Software to correct a harsh bump feel during a 2-1 downshift.WK vehicles equipped with a 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift.DS vehicles equipped with 3.6L engine (Sales Code ERB) Software to correct a harsh bump feel during a 2-1 downshift. Software to address a customer?s concern of less than desired shift quality in Four Wheel Drive (4wd) Low mode during medium to heavy acceleration. Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. Software improvements to powertrain braking in Tow/Haul mode. Software to improve downshift response from a medium to heavy pedal acceleration. Driveability improvements at higher altitudes. Software to improve acceleration during cruise control operation Software to correct a condition where DTC U11C3 - ESM Lost Communication With TCM On D-Pt CAN may have been displayed instead of U11E3 - TCM Lost communication with ESM On D-PT CAN.WD vehicles equipped with a 3.6L engine (Sales Code ERB)

This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.

Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

quality rating when customers experience poor shift quality and if necessary, performing the transmission adaptation learn procedure. In addition, this bulletin involves performing transmission adaptation learn procedure when the transmission is repaired/replaced and/or the valve body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

Includes Various Driveability Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: P0300 - Multiple Cylinder MisfireThe P0300 improvement only applies to vehicles using a block heater in ambient temperatures greater than -20F(-29C). P0606 - Internal Control Processor P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1This release also contains the following improvements: (applies only to LC vehicles) Accuracy improvements for the Automatic Oil Change Indicator (AOCI) system.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak (Sales Code ERB).** U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). P0606 - Internal Control Processor.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak (Sales Code ERB).** U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). P0606 - Internal Control Processor.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): **P0456 - Evap System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit. (2014-2015 MY).** U0140 - Lost Communication With Body Control Module. (LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich.

The Radio does not control phone/Hands Free functionality, it is separate from the radio, test and diagnose the Hands Free Module accordingly.~ Issue 2; Radio inoperative, no power, display no power or screen is blank.~ Blank Screen with Audio: The ICS is a separate module from the radio. If attempting to replace the display (ICS), do not order a radio part number. Instead, order p/n Z5064993A$ for an exchange or 05064993A$ for a new part replacement.~ Issue 3; If the radio ICS/touchscreen display appears to reset intermittently, it turns white then black and functionality returns....Please contact Leony Gonzalez at cell (248) 736-1267 or Dave Clemons at cell (248) 520-0419. Engineering is currently root causing this issue and your assistance is greatly appreciated. If unable to reach this person within 15 minutes, then proceed with the necessary repair. NOTE: USB cables should be replaced prior to the HFM or Radio.

MODEL 2014. *PE

(DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE

this is normal and not a defect.

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

Tire Pressure Sensors Values Are Not Displayed

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

This bulletin involves replacing the fuel pump connector harness (pigtail) when replacing the fuel pump module.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Tire Pressure Sensors Values Are Not Displayed

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

reprogramming the HVAC Module with new software. Customers may experience reduced blower speed when HVAC blower is set to high on MTC vehicles or while using high blower in manual mode on ATC vehicles. Updating the HVAC software will correct this condition.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Control Module with new software or replacing the HVAC Control Module. Customers may experience the blower cutting out when HVAC blower is set to high on Manual Temperature Control (MTC) vehicles or while using high blower in manual mode on Automatic Temperature Controls (ATC) vehicles.

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

http://connectors.dcctools.com/home.htm;jsessionid=C6A3F1B696B030953878BF34FE86A8FE If a connector repair kit is not available on the website contact FCA Redacted Content to see if an alternative repair kit is available for your application prior to ordering the harness. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Customers may experience one of the following:Unpleasant odor in the vehicle after driving from highway speed limits back downto city speed limits. The left temperature door is inoperable(2014-2018 Vehicles Only). Updating the HVAC software will correct these conditions.

Customers may experience a Malfunction Indicator Lamp (MIL)illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set: U0197-00 - Lost Communication With Hands Free Phone Module. Customers may also comment one or more the following: Loss of audio while on a Bluetooth phone call(MYs 2014 - 2019 JC Only). HFM does not boot properly. "Hands-Free Module Loading" is displayed on the head unit. The HFM is inoperative and unresponsive to all user input. The HFM is unresponsive and appears off the bus to wiTECH. Inaccurate foreign language translations. Voice Recognition (VR) is sluggish after changing the language. IPhone 4 starts auto recording itself. Background noise from automated speech recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show ?Musicpaused connecting phone? while a song is being played and without an incoming call. Wrong BTSA screen when deleting. When in Text To Speech (TTS), it will be a mix of the TTS and recording. IPod touch, BTSA will not audio stream. Integrated center stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition was turned off. Automatic Sound Recognition (ASR) microphone picking up background noise. When the language is set for Italian and after the ignition is cycled,the phone screens will change to English(Sales Code RSQ Only). No response from the steering wheel VR button. Not being able to enter into the phone screen on the radio. The customer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English. The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) in the PCM: ? U0140 - Lost Communication With Body Control Module (BCM) (VF, LD, LX Vehicles only). ? P0606 - Internal Control Processor.

Control Module (PCM) with the latest available software A small number of customers may experience less than desired powertrain response when operating their vehicle in high ambient temperatures..

performing a Misc-function routine. The customer may notice a message ?Service Tire Pressure System? displayed on the cluster. On further inspection the technician may find the following Diagnostic Trouble Codes (DTCs): ? C151D - Tire Pressure Sensor Location Undetermined. ? C1581 - Front/Rear Side Tire Pressure Sensor Location Undetermined.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

reprogramming the HVAC Module with new software. Customers may experience reduced blower speed when HVAC blower is set to high on MTC vehicles or while using high blower in manual mode on ATC vehicles. Updating the HVAC software will correct this condition.

This bulletin involves selectively erasing and reprogramming HVAC Control Module with new software or replacing the HVAC Control Module. Customers may experience the blower cutting out when HVAC blower is set to high on Manual Temperature Control (MTC) vehicles or while using high blower in manual mode on Automatic Temperature Controls (ATC) vehicles.

Powertrain Control Module (PCM) with new software. The following powertrain system improvements/enhancements are included in this software release: Corrected a generic scan tool display issue regarding Mode 6 data accuracy.

The customer may experience the following:HFM does not boot properly. "Hands-Free Module Loading" displayedon the head unit.TheHFM is inoperative and unresponsive to all user input.TheHFM is unresponsive and appears off the bus to wiTECH.Inaccurate foreign language translations.VoiceRecognition (VR) is sluggish after changing the language.IPhone4 starts auto recording itself.Backgroundnoise from Automated Speech Recognition. When in Bluetooth Streaming Audio (BTSA) mode, the display will show?Music paused connecting phone? while a song is beingplayed and without an incoming call. Wrong BTSA screen when deleting. Whenin Text To Speech (TTS), it will be a mix of the TTS and recording. IPodtouch, BTSA will not Audio Stream.Integratedcenter stack screen will display ?music paused? afterignition was cycled and BTSA was being used before the ignition wasturned off.AutomaticSound Recognition (ASR) Microphone picking up background noise.WithSales code RSQ, when the language is set for Italian and after theignition is cycled, the phone screens will change to English.No response from the VR button on the steering wheel.Notbeing able to enter into the phone screen on the radio.Technicians may find Diagnostic Trouble Code (DTC) U0197-00 Lost CommunicationWith Hands Free Phone Module, is set. Thecustomer may note when trying to select a non-supported language likeRussian or Portuguese, the Hands Free screen will default to English.The VR will default back to the last language (Italian, French, Spanish,German or Dutch) the customer was using.After the software update has been completed, both the hands free screen and VR will default back to the last language used.Enhancements now include all vehicles, not just internationalvehicles.The following software enhancement isincluded:VR Teleprompter

(PCM) with the latest available software. **P0456 - EVAP System Small Leak (Sales Code ERB).** U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). P0606 - Internal Control Processor.

Customers may describe an unpleasant odor in the vehicle after driving from highway speed limits back down to city speed limits or they may also notice that the left temp door is inoperable. Updating the HVAC software will correct these conditions.

WITH THE LATEST AVAILABLE SOFTWARE. *LJ

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.

Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration update is being released to enable the new wiTECH based ?Quick Learn? procedure to be performed anytime the transmission adaptation memory cells are cleared or addressing customer concerns of poor shift quality. It also addresses customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer's concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

involves selectively erasing and reprogramming the Transmission Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration update is being released to enable the new wiTECH based ?Quick Learn? procedure to be performed anytime the transmission adaptation memory cells are cleared or addressing customer concerns of poor shift quality. It also addresses customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

AVAILABLE FOR VEHICLES EQUIPPED WITH WA580 AUTOMATIC TRANSMISSION *CN

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

The Latch is now released for service under part number 68599540A$.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Cherokee and Dodge Durango) or LD/LX (Dodge Charger and Chrysler 300) 2014, 2015, 2016 MY 0 to 36,000 miles, FCA is looking to gather information prior to repairing the vehicle. Please contact Kevin Murphree via Cell Phone (248) 613-3417.~ If the dealership is within the Metro Detroit Area, Kevin would like to analyze the vehicle in person prior to repair.~

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

These net, form and pierce features are only captured during the line assembly process. It is not a service operation within the assembly line. For repair, the technician must locate, drill and shim the Load Paths, as required. This will allow for the adjustability necessary.

Cherokee and Dodge Durango) or LD/LX (Dodge Charger and Chrysler 300) 2014, 2015, 2016 MY 0 to 36,000 miles, FCA is looking to gather information prior to repairing the vehicle. Please contact Kevin Murphree via Cell Phone (248) 613-3417.~ If the dealership is within the Metro Detroit Area, Kevin would like to analyze the vehicle in person prior to repair.~

software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Navigation screen locks up or display will be blank (Software has been updated to better address this condition). ? Navigation feature lockout disable (International Only) (Software has been updated to better address this condition). ? Intermittently the radio may reset (2014-2015 vehicles). ? Improve FM radio reception (This only applies to 2013 or 2014 LX vehicles with RE6, RB6 radios located in Dubai). ? Radio display screen shows ?Test Mode?. ? Navigation system may resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone aft

software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Navigation screen locks up or display will be blank(Software has been updated to better address this condition). ? Navigation feature lockout disable (International Only)(Software has been updated to better address this condition). ? Intermittently the radio may reset (2014-2015 vehicles). ? Improve FM radio reception (This only applies to 2013 or 2014 LX vehicles with RE6, RB6 radios located in Dubai). ? Radio display screen shows ?Test Mode?. ? Navigation system may resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone after

software and navigation if equipped. A customer may experience, one or more of the following conditions: ? Improve AM/FM radio reception. (This only applies to 2013 or 2014 vehicles with RE6, RB6 radios located in Dubai). ? Intermittently the radio may reset. ? Radio display screen shows ?Test Mode?. ? Navigation screen locks up or display will be blank. ? Navigation feature lockout disable (International Only). ? Navigation system resets intermittently. ? Translation improvements/corrections. ? System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. ? Radio system improvements during remote start operation. ? Unable to adjust radio volume using steering wheel switch intermittently. ? Second screen is blank when using split screen function. ? Some functionality for Japanese and Korean - keyboard, search, sort and jump. ? Unable to add contacts to the favorite list. ? Unable to dial the phone from the radio, while still able to dial from the phone. ? Unable to delete a cell phone number from the favorite list. ? More space available for phone book entries. ? BlackBerry support for playing songs. ? Reduce ticking noise during CD/USB pause and VR is silent between prompts. ? VR unable to transition from Non-navigation to navigation mode. ? iPod screen is displayed with navigation screen. ? Asian language translation added. ? Highlighted preset continues blinking. ? Takes more then one button press to select preset #10. ? Unable to adjust volume from steering wheel switches. ? Clock adjust pop up message displayed in English rather than current language. ? Can not connect to the phone after it has been disconnect. ? Teleprompter screen shows incomplete text. ? Some functionality for traffic & weather jump button. ? After ch

A customer may experience, one or more of the following conditions: Radio display screen shows ?Test Mode?. Navigation screen locks up or display will be blank. Navigation feature lockout disable (International Only). Navigation system resets intermittently. Translation improvements/corrections. System consistency and operational improvements for menu selections, month/date formatting, and Garmin translation functions. Radio system improvements during remote start operation. Unable to adjust radio volume using steering wheel switch intermittently. Second screen is blank when using split screen function. Some functionality for Japanese and Korean - keyboard, search, sort and jump. Unable to add contacts to the favorite list. Unable to dial the phone from the radio, while still able to dial from the phone. Unable to delete a cell phone number from the favorite list. More space available for phone book entries. BlackBerry support for playing songs. Reduce ticking noise during CD/USB pause and VR is silent between prompts. VR unable to transition from Non-navigation to navigation mode. Viod screen is displayed with navigation screen. Asian language translation added. Highlighted preset continues blinking. Takes more then one button press to select preset #10. Unable to adjust volume from steering wheel switches. Clock adjust pop up message displayed in English rather than current language. Can not connect to the phone after it has been disconnect. Teleprompter screen shows incomplete text. Some functionality for traffic & weather jump button. After changing a language and then selecting CDDA ?of? is displayed as a tracking number. In ?Set Date Year? only 3 digits are displayed. Split map view will not cancel. Map screen turns black when driving. When in Italian, the destination arrival text will overlap onto the

removing/installing the bulkhead pass through boot, removing the wiper seal, and applying lubricant to the intermediate shaft bearing sleeve. Customer may describe a squeak and/or moan noise while turning the steering wheel. Noise can be heard both while vehicle is stationary or while driving. Noise is typically more noticeable during cold temperatures and may go away when vehicle warms up.

removing/installing the bulkhead pass through boot, removing the wiper seal, and applying lubricant to the intermediate shaft bearing sleeve. Customer may describe a squeak and/or moan noise while turning the steering wheel. Noise can be heard both while vehicle is stationary or while driving. Noise is typically more noticeable during cold temperatures and may go away when vehicle warms up.

Go to Info Column in Star Parts and open the flow chart to determine which column is installed. If column is Daimler, verify that a replacement Daimler column is in stock and use for replacement. If no Daimler column is in stock, replacement must use Presta column (which require a number of other componenets to be replaced). For more information and details on PN's, see L-Series Flowchart in Star Parts. Contact parts specifying for assistance regarding correct part numbers, for technical assistance contact Star.

If you do not receive a return call within 15 minutes, then proceed with necessary repair.~ Please document all DTCs identified with the scan tool on the repair order narratives.~

needed.

The customer may describe that the cruise control set speed displayed in the IPC will be less than the actual vehicle speed. The following software enhancement is available: Cruise control enhancements.

needed.

modification or replacement of the backlite rear shelf. The customer may describe a rattle or buzz noise coming from the rear of the vehicle with the radio on or while driving on bumpy roads. This may be caused by the rear shelf moving relative to the backlite.

needed.

The customer may describe that the cruise control set speed displayed in the IPC will be less than the actual vehicle speed. The following software enhancement is available: Cruise control enhancements.

ABLE TO DIAL PHONE FROM RADIO BUT CAN DIAL PHONE, TRANSLATION FOR ASIAN LANGUAGE ADDED, AFTER DISCONNECTION PHONE, FAILS TO CONNECT PHONE, ETC. MODEL 2013-14 CHARGER, CHRYSLER 300, JOURNEY. *PE

INSTRUMENT CLUSTER "SERVICE TIRE PRESSURE SYSTEM". *LJ

Rear shock absorbers may have diminished damping performance and/or exhibit signs of weeping.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

Rear shock absorbers may have diminished damping performance and/or exhibit signs of weeping.

ONLY- do not order or install exhaust tips. The tip was eliminated from police models starting with 2014MY.

the right side or both side tension struts. Police vehicles with heavy duty suspension and rear wheel drive may experience a front end clunk noise, coming from the tension strut bushing(s), while coming to a stop.

pivot bushings.

pivot bushings.

the right side or both side tension struts. Police vehicles with heavy duty suspension and rear wheel drive may experience a front end clunk noise, coming from the tension strut bushing(s), while coming to a stop.

industry awareness regarding the use of recycled or salvage parts.

A U11E9, or B16FB-15 may be set

A U11E9, or B16FB-15 may be set

A U11E9, or B16FB-15 may be set

industry awareness regarding the use of recycled or salvage parts.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

Library for specifications so a suitable alternative can be used

B)

(248) 202-7748 to describe system symptoms. If you do not receive a return call within 15 min. please continue with the normal repair.