2020 Dodge Challenger TSBs

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.

? WiFi hotspot gives ?No Internet? connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.41F to JR34.42F. NOTE: The National campaign for this FOTA update launched July 5, 2023.

? Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 34.4 to 34.42.

Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.

Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.

Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch issue, features, modes and App?s change without drivers input (does not affect rearview camera). Wireless connectivity pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

39.5 Customers may experience one or more of the following: High pitch squeal, pop or hum from all speakers. SXM favorite, displays empty song list. Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative.

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

published document)

published document)

39.5 Customers may experience one or more of the following: High pitch squeal, pop or hum from all speakers. SXM favorite, displays empty song list. Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative.

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

completed with emphasis on wiring and connector integrity. If codes C006A-28, U0125-00, or C006A-46 are present, warranty analysis suggests a high likelihood of an intermittent connection at or near the wiring connector, especially if the vehicle is a pursuit variant. Please verify wiring per diagnostic procedures, as well as removal & installation guidance called out in the service manual before replacement.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

and PDM with the latest available software. This software is for vehicles on the RRT VIN List is to improve the function and reliability of the power windows operation.

software to enable High Octane functionality for vehiclesthat have installed the Direct Connection Stage Kits. For customers that have the Direct Connection Redeye Stage I and Stage II kits installed on their vehicle, this flash is requiredto enable functionality of the High Octane Mode.

Customers may experience the following: After Race Cool Down Fan does not function.

Tire Pressure Sensors Values Are Not Displayed

Customers may experience the following: After Race Cool Down Fan does not function.

Customers may experience the following: After Race Cool Down Fan does not function.

Tire Pressure Sensors Values Are Not Displayed

and PDM with the latest available software. This software is for vehicles on the RRT VIN List is to improve the function and reliability of the power windows operation.

Upon further investigation, one or more of the following fault codes may be set in the PCM:

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

The technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:B18BA-12 - Window Control - Circuit Short to Battery B18BA-13 - Window Control - Circuit Open In addition the customer may notice one or more of the following:Driver and/or passenger windows stop working. If the window switch is held in the up position for at least two seconds,the obstruction autodown function may not work. Windows may go up slower than expected.

If no response within 15 minutes, proceed with repair. Please document concern, diagnosis and correction well on repair order or for a possible follow-up call to clearly understand the issue.

If no response in 15 minutes, proceed with repair. Please document concern, diagnosis and correction well on repair order or for a possible follow-up call to clearly understand the issue.

Upon further investigation, one or more of the following fault codes may be set in the PCM:

The customer may describe that they heard about these vehicles that can be unlawfully driven away by thieves when they are able to program new key fobs through the RFHM.Software enhancement include: Update to the RFHM software to prevent hackers from programming their own key fob to the vehicle. This will deter any unwanted drive off of the vehicle without the customers knowledge. Performing this RFHM update will prevent additional key fob programming and this must be communicated to the customer before performing this RFHM update. If additional keys are required by the customer after this RFHM update is performed the replacement of the RFHM is required and must be at a previous SW level.

and PDM with the latest available software. This software is for vehicles on the RRT VIN List is to improve the function and reliability of the power windows operation.

The technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:B18BA-12 - Window Control - Circuit Short to Battery B18BA-13 - Window Control - Circuit Open In addition the customer may notice one or more of the following:Driver and/or passenger windows stop working. If the window switch is held in the up position for at least two seconds,the obstruction autodown function may not work. Windows may go up slower than expected.

If no response within 15 minutes, proceed with repair. Please document concern, diagnosis and correction well on repair order or for a possible follow-up call to clearly understand the issue.

If no response in 15 minutes, proceed with repair. Please document concern, diagnosis and correction well on repair order or for a possible follow-up call to clearly understand the issue.

lens is clean and camera image does not change by wiggling rear view camera harness. If concern is still present, remove the camera and check the connector terminal for damage or water intrusion. Please document any findings in the repair notes.

This bulletin involves replacing the Powertrain Control Module (PCM) and re-programming with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find the following Diagnostic Trouble Code (DTC) set in the PCM memory:P2172 - High Airflow/Vacuum Leak Detected (Instantaneous Accumulation).

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

and PDM with the latest available software. Customers may comment on the following:Driver and passenger windows makes a clunk sound when the window is fully open.

and PDM with the latest available software. Customers may comment on the following:Driver and passenger windows makes a clunk sound when the window is fully open.

and PDM with the latest available software. Customers may comment on the following:Driver and passenger windows makes a clunk sound when the window is fully open.

Stop Start Equipped Vehicles

Replacements

Replacements

body replacement."

Brake Pedal Position Sensor Circuit Performance, P1572 Brake Pedal Stuck, C0042-54 Brake Pedal Missing Calibration

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. This bulletin involves replacing the urea delivery module and grade vent valve and updating the Dosing Control Unit (DCU) software.

Brake Pedal Position Sensor Circuit Performance, P1572 Brake Pedal Stuck, C0042-54 Brake Pedal Missing Calibration

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** Wireless connectivity pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXMT icon inoperative. SXMT favorite song not displaying/playing. High pitch squeal, pop or hum noise from speakers. Anti-theft code request message. Lines appear across screen. Radio will not switch modes between AM, FM, SAT or Media. Performance control home screen shows ?Norm? mode for engine/transmission even when the vehicle is in ?Drag? mode (LA, LD, LX only). Can not change the time on the clock (LA, LD and LX only). USB hub inoperable (D-Trucks only). Backup camera gridlines missing (D-Trucks only). Device not supported message (D-Trucks only). Remote app inoperative (D-Trucks only). Unable to adjust volume (D-Trucks only). Heated steering wheel inoperable (D-Trucks only). In addition, the following enhancement are included in this update: CarplayT connectivity improvements. Improvement to wireless connectivity phone pairing. Improved sound quality when using a wireless connectivity phone. **This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.**

installed in the vehicle.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) has been set:P0441 - EVAP Purge System Performance. P0452 - EVAP Pressure Switch Stuck Closed.

(ETL, ETM, ETN Engines)

Customers may experience the following:The transmission shifts to neutral or the engine stalls, when the brakes are applied very suddenly and aggressively to bring the vehicle to a complete stop.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

passenger side.

39.5 Customers may experience one or more of the following: Performance control home screen shows "Norm" mode for engine/transmission even when the vehicle is in "Drag" mode. High pitch squeal, pop or hum from all speakers. SXM favorite, displays empty song list. Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative.

passenger side.

Technician may find DTC?s B18BA-12 - Window Control - Circuit Short to Battery, B18BA-13 - Window Control - Circuit Open (stored or active). Replace the DDM or PDM per detailed repair information in Service Library or reference Star Online Publlication S2008000182. Replacing regulators or motors will not correct this issue.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) has been set:P0441 - EVAP Purge System Performance. P0452 - EVAP Pressure Switch Stuck Closed.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) has been set:P0441 - EVAP Purge System Performance. P0452 - EVAP Pressure Switch Stuck Closed.

seals: These O-Rings are now available for service. The green O-Ring is part 68029299A$. The black O-Ring is to be serviced by the green O-Ring. The blue O-Ring (thicker cross section than green & black) is part 68029300A$.~ If ordering this oil filler cap for a warranty repair due to a damaged/missing O-ring, please note that returned caps replaced for an O-ring issue will be subject to chargeback.

P3449, P3441, P3425, And P3401 May Be Set In The PCM

The customer may describe that vehicle has an exhaust rattle on acceleration and deceleration in1500-2400 RPM range when the sport mode is off.

Sensor Circuit Performance

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

Window Will Not Lower/Raise When Door Is Opened Or Closed, Diagnostic Trouble Code (DTC) B25B4-2A Pawl Switch Stuck.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Window When The Door Is Closed

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Window When The Door Is Closed

When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.

when the outside door handle is actuated latch replacement may be unneccessary. please contact the following individual prior to servicing the vehicle FCA Redacted Content There is a simple door handle to latch adjustment specified in the latch installation service procedure. 23 - Body / Doors - Front / LATCH, Door / Installation. The handle/latch/window switch adjustment is specified in steps 7 through 9.

when the outside door handle is actuated latch replacement may be uneccessary. There is a simple door handle to latch adjustment specified in the latch installation service procedure. 23 - Body / Doors - Front / LATCH, Door / Installation. The handle/latch/window switch adjustment is specified in steps 7 through 9.

When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Window When The Door Is Closed

this is normal and not a defect.

semi and full synthetic oils.

Drive Belt May Come Off Pulleys Due To Ice

Detected Message

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

Customers may experience the following: A large gap can be seen on the sides of the license plate bracket.

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.

used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch. "

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.

the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead.

Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead.

surfaces between the hub and rotor. The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.

The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.

surfaces between the hub and rotor. The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.

surfaces between the hub and rotor. The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.

The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.

surfaces between the hub and rotor. The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.

The customer may comment on the following:When making a sharp turn at low speed (parking lot) maneuvers, a click noise is heard. Most of the time the noise can be heard if the windows are open.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find following Diagnostic Trouble Code (DTC):P04FC - Crankcase Ventilation System Performance. Customer may also experience the following:Unable to set the cruise control above 132 km/h (82 mph). A hard brake pedal at higher altitudes. Software enhancements also includes the following: Improved brake pedal feel at higher altitude. Cruise control enhancement.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Library for specifications so a suitable alternative can be used

Cameras must be inoperative or fail the blurry image test to be eligible for warranty. All parts must be returned for analysis. If parts are found to be working as designed and trouble not found, a chargeback may be applied. Prior to camera replacement, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

The customer may notice:The vehicle has the incorrect wheels on it.FCA will contact each customer for the RRT and inquire their wheel preference. For the customers who are satisfied and want to retain possession of their current wheels, FCA will remove them from the RRT population from VIP. For the customers that are dissatisfied and want their wheels replaced, FCA will schedule an appointment at the customers local dealership during the initialphone call. The dealership will then be contacted by FCA and finalize the appointment time and notify them to order the correct wheels

for Moisture / Condensation issue, please e-mail pictures of the Moisture / Condensation issue to FCA Redacted Content and then continue with the replacement.

DO NOT remove actuators 2. Verify noise by cycling EEV manually via WiTech 3. Verify noise with test drive (optional) 4. If the noise is confirmed, replace the system without removing the actuators.

Customers may experience one or more of the following:Radio display screen flickers. Radio resets with RPM less than 1000 RPM (DT and JL with 3.0L Diesel). Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.

Customers may experience one or more of the following:Radio display screen flickers. Radio resets with RPM less than 1000 RPM (DT and JL with 3.0L Diesel). Clock loses 6 seconds per day (JL with 5 inch screen). Ghost Touch, features, modes and App?s changing without drivers input. Bluetooth pop noise. Pop message ?SXM Wait? displayed for extended period of time. The radio resets.

"

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

system

heater core but also the connecting tubes, seals and retainers. For any questions contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

heater core but also the connecting tubes, seals and retainers. For any questions contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

heater core but also the connecting tubes, seals and retainers. For any questions contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

as Splash Shield) for rub marks and replacing if needed. Customers may experience the following:A rubbing noise in the right front when make hard left turns.

as Splash Shield) for rub marks and replacing if needed. Customers may experience the following:A rubbing noise in the right front when make hard left turns.

B)