2015 Dodge Challenger TSBs

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P0300 - Multiple Cylinder Misfire (manual transmission applications only). ? P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. ? P2227 - Barometric Pressure Circuit Performance In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH.

Module (TCM) with the latest available software. A small number of customers may experience one or more of the following concerns. These concerns are broken up per engine and transmission combination. 6.2L engine (sales code ESD) equipped with an 8HP90 transmission (sales code DFE) ? Transmission will not upshift during Wide Open Throttle (WOT) acceleration. ? Harsh or inconsistent coasting downshifts. ? Transmission will not shift into 7th gear during high speed driving. ? Inconsistent or busy shifts during stop and go traffic. ? Inconsistent gear shift patterns when driving on grades. ? Malfunction Indicator Lamp (MIL) Illumination during ABS activated stops with Diagnostic Trouble Code (DTC) P1DCD TCM Monitoring Processor Performance, Multiple Clutches Locked Up. 6.4L engine (sales code ESG) and equipped with an 8HP70 transmission (sales code DFK) ? Harsh or inconsistent 1-2 upshift. ? Harsh of inconsistent coasting 4-3 downshift. ? Harsh or inconsistent gear engagement when shifting to drive or reverse. ? Instrument Panel Cluster (IPC) shows the incorrect gear when in manual mode. ? Harsh of inconsistent shifts during tip-in acceleration from closed throttle. ? Inconsistent gear shift patterns when driving on grades. ? Inconsistent release of Hill Start Assist during tip-in acceleration. ? Transmission upshifts on sweeping curves under track driving conditions.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P0300 - Multiple Cylinder Misfire (manual transmission applications only). ? P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. ? P2227 - Barometric Pressure Circuit Performance In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH.

Module (TCM) with the latest available software. A small number of customers may experience one or more of the following concerns. These concerns are broken up per engine and transmission combination. 6.2L engine (sales code ESD) equipped with an 8HP90 transmission (sales code DFE) ? Transmission will not upshift during Wide Open Throttle (WOT) acceleration. ? Harsh or inconsistent coasting downshifts. ? Transmission will not shift into 7th gear during high speed driving. ? Inconsistent or busy shifts during stop and go traffic. ? Inconsistent gear shift patterns when driving on grades. ? Malfunction Indicator Lamp (MIL) Illumination during ABS activated stops with Diagnostic Trouble Code (DTC) P1DCD TCM Monitoring Processor Performance, Multiple Clutches Locked Up. 6.4L engine (sales code ESG) and equipped with an 8HP70 transmission (sales code DFK) ? Harsh or inconsistent 1-2 upshift. ? Harsh of inconsistent coasting 4-3 downshift. ? Harsh or inconsistent gear engagement when shifting to drive or reverse. ? Instrument Panel Cluster (IPC) shows the incorrect gear when in manual mode. ? Harsh of inconsistent shifts during tip-in acceleration from closed throttle. ? Inconsistent gear shift patterns when driving on grades. ? Inconsistent release of Hill Start Assist during tip-in acceleration. ? Transmission upshifts on sweeping curves under track driving conditions.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information

installed in the vehicle.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P0300 - Multiple Cylinder Misfire (manual transmission applications only). ? P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. ? P2227 - Barometric Pressure Circuit Performance In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH.

Module (TCM) with the latest available software. A small number of customers may experience one or more of the following concerns. These concerns are broken up per engine and transmission combination. 6.2L engine (sales code ESD) equipped with an 8HP90 transmission (sales code DFE) ? Transmission will not upshift during Wide Open Throttle (WOT) acceleration. ? Harsh or inconsistent coasting downshifts. ? Transmission will not shift into 7th gear during high speed driving. ? Inconsistent or busy shifts during stop and go traffic. ? Inconsistent gear shift patterns when driving on grades. ? Malfunction Indicator Lamp (MIL) Illumination during ABS activated stops with Diagnostic Trouble Code (DTC) P1DCD TCM Monitoring Processor Performance, Multiple Clutches Locked Up. 6.4L engine (sales code ESG) and equipped with an 8HP70 transmission (sales code DFK) ? Harsh or inconsistent 1-2 upshift. ? Harsh of inconsistent coasting 4-3 downshift. ? Harsh or inconsistent gear engagement when shifting to drive or reverse. ? Instrument Panel Cluster (IPC) shows the incorrect gear when in manual mode. ? Harsh of inconsistent shifts during tip-in acceleration from closed throttle. ? Inconsistent gear shift patterns when driving on grades. ? Inconsistent release of Hill Start Assist during tip-in acceleration. ? Transmission upshifts on sweeping curves under track driving conditions.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

A small number of customers may experience one or more of the following: ? **?Navigation Failed? message is displayed. ? Navigation is inoperative or inaccurate. ? CD player will not play songs and/or locks up the radio. ? The clock will not automatically update to local time. ? The clock may be off by several hours (RA3 only). ? HVAC temperature out of sync with radio display (KL vehicles). ? Some Uconnect App remote commands do not execute with the vehicle. ? Radio Apps are inoperative. ? Radio will lock up. Radio display screen is black or blank. Battery drain due to radio staying on.** Rearview Camera image appears jittery (UF vehicles only). Inability to establish a WiFi connection when security feature is enabled (UF vehicles only). Audio distortion/popping heard while playing Apple devices through the USB port (UF vehicles only). Remote Uconnect Apps functions (i.e. door locks, remote start) inoperative while the engine is running (UF vehicles only). HVAC temperature out of sync with radio display (KL vehicles). Intermittently blind spot chime will not turn off (KL vehicles only). The radio may switch from SiriusXMT to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Audio muted after AUX device is disconnected. In addition, the following Improvements are included: **Adds Apple SiriT Eyes Free capability for iPhoneT owners. Add the ability to drag and drop icons into the menu bar. Auto Play can now be configured. Enhanced VR performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (YelpT, PandoraT, AhaT, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature.**

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory:P0456 - EVAP System Small Leak. U1424 - Implausible Engine Torque Signal Received. P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P2299 - Brake Pedal Position/Accelerator Pedal Position Incompatible. P2227 - Barometric Pressure Circuit Performance. P1611 - Supercharger Bypass Valve Position Sensor 1 Circuit High. P0513 - Invalid Skim Key. P0300 - Multiple Cylinder Misfire (Sales Code DEC only). P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. P1217 - Active Exhaust Valve 1 Performance. P121B - Active Exhaust Valve 2 Performance. The P0513 DTC is set during remote starting the vehicle and nearly simultaneously pressing the key fob button against the Keyless Ignition Node (KIN) causing an engine stall.The PCM software also enables freeze frame/failure records to be stored for the following diagnostic trouble codes:P0102 - MAF sensor circuit shorted to ground. P0103 - MAF Sensor Circuit shorted High. P0607 - ECU Internal Performance. P060E - Level 2 TPS Sensor Coherency Check Has Failed. P1610 - Supercharger Bypass Valve Position Sensor 1 Circuit Low. P1611 - Supercharger Bypass Valve Position Sensor 1 Circuit High. P1616 - Supercharger Bypass Valve Position Sensor 2 Circuit Low. P1617 - Supercharger Bypass Valve Position Sensor 2 Circuit High. P1620 - Supercharger Bypass Valve Control Open Circuit. P1627 - Supercharger Bypass Valve Position Sensor 1/2 Correlation. P162A - Supercharger Bypass Valve Actuator Control System - Max PWM Exceeded.

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

Communication or DTC issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of VSR to be emailed to the above address. B) Noise or Mechanical issue please contact: Barbara Strace @ cell (586) 246-4211. If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to attach a copy of the Vehicle Scan Report on the repair order.

Module (TCM) with the latest available software. A small number of customers may experience an erroneous Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find a Diagnostic Trouble Code (DTC) stored in the TCM memory. 3.6L Engine (Sales Code ERB) with 845RE Transmission (Sales Code DFL): **Improved shift quality.** P1DCD - TCM monitoring processor performance multiple clutches locked up. P1B13 - Park-By-Wire unintended out of park position. P0734 - Gear 4 Shift Incorrect Ratio. 3.6L Engine (Sales Code ERB) with 8HP45 Transmission (Sales Code DFG): **Improved shift quality.** Harsh 2-1 downshift or bump at low speeds. P0734 - Gear 4 Shift Incorrect Ratio. 3.0L Engine (Sales Code EHD) with 845RE Transmission (Sales Code DFL): **Improved shift quality.** P1DCD - TCM monitoring processor performance multiple clutches locked up. P1B13 - Park-By-Wire unintended out of park position.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following (DTCs) set in the PCM memory: **P0456 - EVAP System Small Leak. P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance.** U0140 - Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful. P0300 - Multiple Cylinder Misfire. P0573 - Brake Switch 1 Stuck Off.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

2015-2016 6.2L Supercharged Hellcat equipped Challengers/Chargers for a P2227 (Barometric Pressure Circuit Performance) fault, please call Nick Lynn on his cell (586) 295-0917. If no response is received within 15 minutes, please continue with repair.

at emailjason.maltese@fcagroup.com before replacing this part. Engineering may want to visit dealers in the SE Michigan area to investigate this issue. If no answer and if you do not receive a return call within 15 minutes please continue with the normal repair.

2015-2016 6.2L Supercharged Hellcat equipped Challengers/Chargers for a P2227 (Barometric Pressure Circuit Performance) fault, please call Nick Lynn on his cell (586) 295-0917. If no response is received within 15 minutes, please continue with repair.

at emailjason.maltese@fcagroup.com before replacing this part. Engineering may want to visit dealers in the SE Michigan area to investigate this issue. If no answer and if you do not receive a return call within 15 minutes please continue with the normal repair.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

working on any 15 MY Challenger, or 16 MY Challenger built before 4/25/2016 an engineering change has been made to the synchronizer material to provide better wear characteristics. Service parts are in stock and available for repairs, part number 68028593A$.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Engineering is looking to gather infomation on fail mode and customer concern. If no response in 15 minutes, proceed with repair.

2015-2016 6.2L Supercharged Hellcat equipped Challengers/Chargers for a P2227 (Barometric Pressure Circuit Performance) fault, please call Nick Lynn on his cell (586) 295-0917. If no response is received within 15 minutes, please continue with repair

information regarding this part.~ Bob Smith ? Cell (248) 202-9458 - Robert.M.Smith@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~

2015-2016 6.2L Supercharged Hellcat equipped Challengers/Chargers for a P2227 (Barometric Pressure Circuit Performance) fault, please call Nick Lynn on his cell (586) 295-0917. If no response is received within 15 minutes, please continue with repair.

at emailjason.maltese@fcagroup.com before replacing this part. Engineering may want to visit dealers in the SE Michigan area to investigate this issue. If no answer and if you do not receive a return call within 15 minutes please continue with the normal repair.

Module (PCM) with the latest software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). Symptoms: ? Unable to accurately increase or decrease the cruise control set speed using the resume or set buttons while the instrument cluster is set on metric units. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. ? Slight spark knock condition during aggressive high speed driving which may prevent the vehicle from achieving maximum top speed. DTCs: ? P1217 - Active Exhaust Valve 1 Performance ? P121B - Active Exhaust Valve 2 Performance ? P2227 - Barometric Pressure Circuit Performance

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P0300 - Multiple Cylinder Misfire (manual transmission applications only). ? P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. ? P2227 - Barometric Pressure Circuit Performance In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH.

The customer may notice the right side engine cover is missing. Only the right side engine cover was missed during vehicle assembly, the left side of the engine does not get an engine cover and is not part of this service action.

Module (PCM) with the latest software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). (LA) Challenger and (LD) Charger (Sales Code ESD Only) ? P0513 - Invalid Skim Key. This code is set during remote starting the vehicle and nearly simultaneously pressing the Key Fob button against the Keyless Ignition Node (KIN), causing an engine stall. In addition the PCM software also enables freeze frame/failure records to be stored for the following Diagnostic Trouble Codes: ? P0102 - MAF sensor circuit shorted to ground. ? P0103 - MAF Sensor Circuit shorted High. ? P0607 - ECU Internal Performance. ? P060E - Level 2 TPS sensor coherency check has failed. ? P1610 - Supercharger Bypass Valve Position Sensor 1 Circuit Low. ? P1611 - Supercharger Bypass Valve Position Sensor 1 Circuit High. ? P1616 - Supercharger Bypass Valve Position Sensor 2 Circuit Low. ? P1617 - Supercharger Bypass Valve Position Sensor 2 Circuit High. ? P1620 - Supercharger Bypass Valve Control Open Circuit. ? P1627 - Supercharger Bypass Valve Position Sensor 1/2 Correlation. ? P162A - Supercharger Bypass Valve Actuator Control System - Max PWM Exceeded. ? P162C - Supercharger Bypass Valve Control Circuit. ? Unable to accurately increase or decrease the cruise control set speed using the resume or set buttons while the instrument cluster is set on metric units. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. ? Slight spark knock condition during aggressive high speed driving which may prevent the vehicle from achieving maximum top speed. ? P1217 - Active Exhaust Valve 1 Performance. ?

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P219A - Bank 1 Air-Fuel Ratio Imbalance ? P219B - Bank 2 Air-Fuel Ratio Imbalance ? P0307 - Cylinder 7 Misfire ? P2096 - Downstream Fuel Trim System 1 Lean ? P2097 - Downstream Fuel Trim System 1 Rich Additional Symptoms: ? Engine buck or delay feeling during low speed driving. ? Less than desired engine performance during Multiple Displacement System (MDS) mode transitions.

Vehicles included on the RRT VIN list may have been built with the incorrect valve stems and TPM sensors.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory. ? P0300 - Multiple Cylinder Misfire (manual transmission applications only). ? P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. ? P2227 - Barometric Pressure Circuit Performance In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH.

Module (TCM) with the latest available software. A small number of customers may experience one or more of the following concerns. These concerns are broken up per engine and transmission combination. 6.2L engine (sales code ESD) equipped with an 8HP90 transmission (sales code DFE) ? Transmission will not upshift during Wide Open Throttle (WOT) acceleration. ? Harsh or inconsistent coasting downshifts. ? Transmission will not shift into 7th gear during high speed driving. ? Inconsistent or busy shifts during stop and go traffic. ? Inconsistent gear shift patterns when driving on grades. ? Malfunction Indicator Lamp (MIL) Illumination during ABS activated stops with Diagnostic Trouble Code (DTC) P1DCD TCM Monitoring Processor Performance, Multiple Clutches Locked Up. 6.4L engine (sales code ESG) and equipped with an 8HP70 transmission (sales code DFK) ? Harsh or inconsistent 1-2 upshift. ? Harsh of inconsistent coasting 4-3 downshift. ? Harsh or inconsistent gear engagement when shifting to drive or reverse. ? Instrument Panel Cluster (IPC) shows the incorrect gear when in manual mode. ? Harsh of inconsistent shifts during tip-in acceleration from closed throttle. ? Inconsistent gear shift patterns when driving on grades. ? Inconsistent release of Hill Start Assist during tip-in acceleration. ? Transmission upshifts on sweeping curves under track driving conditions.

Module with the latest available software. A small number of customers may experience a slight spark knock condition during aggressive high speed driving. They may state that when this occurs, the vehicle is unable to achieve maximum top speed. No Diagnostic Trouble Codes (DTCs) are associated with this condition. In addition, customers may also comment that, with the cluster set on metric units, they are unable to accurately increase or decrease the cruise control set speed using the resume or set buttons. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH.

Module (TCM) with the latest available software. A small number of customers may experience one or more of the following concerns. These concerns are broken up per engine and transmission combination. 6.2L engine (sales code ESD) equipped with an 8HP90 transmission (sales code DFE) ? Transmission will not upshift during Wide Open Throttle (WOT) acceleration. ? Harsh or inconsistent coasting downshifts. ? Transmission will not shift into 7th gear during high speed driving. ? Inconsistent or busy shifts during stop and go traffic. ? Inconsistent gear shift patterns when driving on grades. ? Malfunction Indicator Lamp (MIL) Illumination during ABS activated stops with Diagnostic Trouble Code (DTC) P1DCD TCM Monitoring Processor Performance, Multiple Clutches Locked Up. 6.4L engine (sales code ESG) and equipped with an 8HP70 transmission (sales code DFK) ? Inconsistent 1-2 upshifts when first shifting after a cold soak or in colder ambient temperatures. ? Delayed engagement when shifting from reverse to drive. ? Harsh or inconsistent 1-2 upshift during normal driving. ? Harsh of inconsistent coasting 4-3 downshift. ? Harsh or inconsistent gear engagement when shifting to drive or reverse. ? Instrument Panel Cluster (IPC) shows the incorrect gear when in manual mode. ? Harsh of inconsistent shifts during tip-in acceleration from closed throttle. ? Inconsistent gear shift patterns when driving on grades. ? Inconsistent release of Hill Start Assist during tip-in acceleration. ? Transmission upshifts on sweeping curves under track driving conditions. In addition to the above conditions, this software release also enables the capability to capture non Diagnostic Trouble Code (DTC) control module data through the Uconnect Data Recording system.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful. ? P0300 Multiple Cylinder Misfire. ? P0573 Brake Switch 1 Stuck Off.

working on any 15 MY Challenger, or 16 MY Challenger built before 4/25/2016 an engineering change has been made to the synchronizer material to provide better wear characteristics. Service parts are in stock and available for repairs, part number 68028593A$.

Module (TCM) with the latest available software. A small number of customers may experience an erroneous Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find a Diagnostic Trouble Code (DTC) stored in the TCM memory. 3.6L Engine (Sales Code ERB) with 845RE Transmission (Sales Code DFL): **Improved shift quality.** P1DCD - TCM monitoring processor performance multiple clutches locked up. P1B13 - Park-By-Wire unintended out of park position. P0734 - Gear 4 Shift Incorrect Ratio. 3.6L Engine (Sales Code ERB) with 8HP45 Transmission (Sales Code DFG): **Improved shift quality.** Harsh 2-1 downshift or bump at low speeds. P0734 - Gear 4 Shift Incorrect Ratio. 3.0L Engine (Sales Code EHD) with 845RE Transmission (Sales Code DFL): **Improved shift quality.** P1DCD - TCM monitoring processor performance multiple clutches locked up. P1B13 - Park-By-Wire unintended out of park position.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following (DTCs) set in the PCM memory: **P0456 - EVAP System Small Leak. P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance.** U0140 - Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful. P0300 - Multiple Cylinder Misfire. P0573 - Brake Switch 1 Stuck Off.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

the Powertrain Control Module (PCM) and Transmission Control Module (TCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory: **P0456 - EVAP System Small Leak. P1611 - Supercharger Bypass Valve Position Sensor 1 Circuit High. P0513 - Invalid Skim Key.** P0300 - Multiple Cylinder Misfire (manual transmission applications only). P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. P2227 - Barometric Pressure Circuit Performance. P1217 - Active Exhaust Valve 1 Performance. P121B - Active Exhaust Valve 2 Performance. **The P0513 code is set during remote starting the vehicle and nearly simultaneously pressing the Key Fob button against the Keyless Ignition Node (KIN) causing an engine stall.** **In addition the PCM software also enables freeze frame/failure records to be stored for the following Diagnostic Trouble Codes: P0102 - MAF sensor circuit shorted to ground. P0103 - MAF Sensor Circuit shorted High. P0607 - ECU Internal Performance. P060E - Level 2 TPS sensor coherency check has failed. P1610 - Supercharger Bypass Valve Position Sensor 1 Circuit Low. P1611 - Supercharger Bypass Valve Position Sensor 1 Circuit High. P1616 - Supercharger Bypass Valve Position Sensor 2 Circuit Low. P1617 - Supercharger Bypass Valve Position Sensor 2 Circuit High. P1620 - Supercharger Bypass Valve Control Open Circuit. P1627 - Supercharger Bypass Valve Position Sensor 1/2 Correlation. P162A - Supercharger Bypass Valve Actuator Control System - Max PWM Exceeded. P162C - Supercharger Bypass Valve Control Circuit.** In addition, customers may also comment on the following:

(PCM) with the latest available software. A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): P1217 - Active Exhaust Valve 1 Performance. P121B - Active Exhaust Valve 2 Performance. In addition, customers may also comment on the following: Unable to accurately increase or decrease the cruise control set speed using the resume or set buttons while the instrument cluster is set on metric units. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. Slight spark knock condition during aggressive high speed driving which may prevent the vehicle from achieving maximum top speed.

Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~

Adaptation Learn procedure based on a subjective shift quality rating evaluation.The adaptation drive learn procedure must be performed on all 8-speed transmissions when the transmission is repaired/replaced and/or the Valve Body/TCU assembly (mechatronic) is replaced, or when the adaptation memory cells are cleared with the wiTECH diagnostic scan tool. Customers may indicate that their transmission shift quality does not meet their expectations.

A small number of customers may experience one or more of the following: ? **?Navigation Failed? message is displayed. ? Navigation is inoperative or inaccurate. ? CD player will not play songs and/or locks up the radio. ? The clock will not automatically update to local time. ? The clock may be off by several hours (RA3 only). ? HVAC temperature out of sync with radio display (KL vehicles). ? Some Uconnect App remote commands do not execute with the vehicle. ? Radio Apps are inoperative. ? Radio will lock up. Radio display screen is black or blank. Battery drain due to radio staying on.** Rearview Camera image appears jittery (UF vehicles only). Inability to establish a WiFi connection when security feature is enabled (UF vehicles only). Audio distortion/popping heard while playing Apple devices through the USB port (UF vehicles only). Remote Uconnect Apps functions (i.e. door locks, remote start) inoperative while the engine is running (UF vehicles only). HVAC temperature out of sync with radio display (KL vehicles). Intermittently blind spot chime will not turn off (KL vehicles only). The radio may switch from SiriusXMT to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Audio muted after AUX device is disconnected. In addition, the following Improvements are included: **Adds Apple SiriT Eyes Free capability for iPhoneT owners. Add the ability to drag and drop icons into the menu bar. Auto Play can now be configured. Enhanced VR performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (YelpT, PandoraT, AhaT, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature.**

Communication or DTC issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of VSR to be emailed to the above address. B) Noise or Mechanical issue please contact: Barbara Strace @ cell (586) 246-4211. If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to attach a copy of the Vehicle Scan Report on the repair order.

Communication or DTC issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of VSR to be emailed to the above address. B) Noise or Mechanical issue please contact: Barbara Strace @ cell (586) 246-4211. If you do not receive a return call within 15 minutes, proceed with the repair. Please be sure to attach a copy of the Vehicle Scan Report on the repair order.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

Module (TCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following Diagnostic Trouble Codes (DTCs) have been set. This software update will also address some symptom/conditions listed below:3.6L Engine (Sales Code ERB) with 845RE Transmission (Sales Code DFL):During a Flash Over The Air (FOTA) radio update, the transmission shift points will default to higher shift points. The transmission will shift at high engine Revolutions Per Minute (RPM) and 7th and 8th gears may be blocked (LA and LD). Improved shift quality. P1DCD - TCM Monitoring Processor Performance Multiple Clutches Locked Up. P1B13 - Park-By-Wire Unintended Out Of Park Position. P0734 - Gear 4 Shift Incorrect Ratio. 3.6L Engine (Sales Code ERB) with 8HP45 Transmission (Sales Code DFG):During a FOTA radio update, the transmission shift points will default to higher shift points. The transmission will shift at high engine RPM and 7th and 8th gears may be blocked (LA and LD). Improved shift quality. Harsh 2-1 Downshift Or Bump At Low Speeds. P0734 - Gear 4 Shift Incorrect Ratio. 3.0L Engine (Sales Code EHD) with 845RE Transmission (Sales Code DFL):Improved shift quality. P1DCD - TCM Monitoring Processor Performance Multiple Clutches Locked Up. P1B13 - Park-By-Wire Unintended Out Of Park Position.

If a cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people. First: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com Second: Kevin Refalo - Cell (248) 260-0738 Kevin.refalo@facgroup.com If no response in 15 minutes, proceed with repair.

If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): **P0456 - Evap System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit. (2014-2015 MY).** U0140 - Lost Communication With Body Control Module. (LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich.

WITH THE LATEST AVAILABLE SOFTWARE. CUSTOMERS MAY EXPERIENCE ONE OR MORE OF THE FOLLOWING SYMPTOMS AND/OR A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND ONE OR MORE OF THE FOLLOWING DTCS: **P2299 - BRAKE PEDAL POSITION/ACCELERATOR PEDAL POSITION INCOMPATIBLE. P0456 - EVAP SYSTEM SMALL LEAK. P2610 - PCM INTERNAL ENGINE OFF TIMER PERFORMANCE. P2172 - HIGH AIRFLOW/VACUUM LEAK DETECTED (INSTANTANEOUS ACCUMULATION). P0123 - THROTTLE POSITION SENSOR 1 CIRCUIT HIGH. P0223 - THROTTLE POSITION SENSOR 2 CIRCUIT HIGH. P0122 - THROTTLE POSITION SENSOR 1 CIRCUIT LOW. P0222 - THROTTLE POSITION SENSOR 2 CIRCUIT LOW. P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. P0339 - CRANKSHAFT POSITION SENSOR INTERMITTENT.** P1217 - ACTIVE EXHAUST VALVE 1 PERFORMANCE. P121B - ACTIVE EXHAUST VALVE 2 PERFORMANCE. **THE FOLLOWING SOFTWARE ENHANCEMENT IS ALSO AVAILABLE: CHANGE TO PURGE VAPOR CONTROL CALIBRATION.** IN ADDITION, CUSTOMERS MAY ALSO COMMENT ON THE FOLLOWING: UNABLE TO ACCURATELY INCREASE OR DECREASE THE CRUISE CONTROL SET SPEED USING THE RESUME OR SET BUTTONS WHILE THE INSTRUMENT CLUSTER IS SET ON METRIC UNITS. INSTEAD OF CHANGING VEHICLE SPEED BY 1 KPH WHEN PRESSING THE BUTTONS, THE VEHICLE SPEED WILL INCREASE APPROXIMATELY 1.6 KPH. SLIGHT SPARK KNOCK CONDITION DURING AGGRESSIVE HIGH SPEED DRIVING WHICH MAY PREVENT THE VEHICLE FROM ACHIEVING MAXIMUM TOP SPEED."

68319331AA~ - IF SPRING IS NOT BROKEN AND REPLACING ACTUATOR, PLEASE CONTACT JASON MALTESE CELL (248) 931-4179 - EXHAUST ENGINEER. ~ IF NO RESPONSE IN 15 MINUTES, PROCEED WITH REPAIR"

CONTROL MODULE (TCM) WITH THE LATEST AVAILABLE SOFTWARE. A SMALL NUMBER OF CUSTOMERS MAY EXPERIENCE AN ERRONEOUS MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION, THE TECHNICIAN MAY FIND A DIAGNOSTIC TROUBLE CODE (DTC) STORED IN THE TCM MEMORY. 3.6L ENGINE (SALES CODE ERB) WITH 845RE TRANSMISSION (SALES CODE DFL): **IMPROVED SHIFT QUALITY.** P1DCD - TCM MONITORING PROCESSOR PERFORMANCE MULTIPLE CLUTCHES LOCKED UP. P1B13 - PARK-BY-WIRE UNINTENDED OUT OF PARK POSITION. P0734 - GEAR 4 SHIFT INCORRECT RATIO. 3.6L ENGINE (SALES CODE ERB) WITH 8HP45 TRANSMISSION (SALES CODE DFG): **IMPROVED SHIFT QUALITY.** HARSH 2-1 DOWNSHIFT OR BUMP AT LOW SPEEDS. P0734 - GEAR 4 SHIFT INCORRECT RATIO. 3.0L ENGINE (SALES CODE EHD) WITH 845RE TRANSMISSION (SALES CODE DFL): **IMPROVED SHIFT QUALITY.** P1DCD - TCM MONITORING PROCESSOR PERFORMANCE MULTIPLE CLUTCHES LOCKED UP. P1B13 - PARK-BY-WIRE UNINTENDED OUT OF PARK POSITION."

CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION THE TECHNICIAN MAY FIND THE FOLLOWING (DTCS) SET IN THE PCM MEMORY: **P0456 - EVAP SYSTEM SMALL LEAK. P0335 - CRANKSHAFT POSITION SENSOR CIRCUIT. P2610 - PCM INTERNAL ENGINE OFF TIMER PERFORMANCE.** U0140 - LOST COMMUNICATION WITH BODY CONTROL MODULE. ATTEMPTING TO CLEAR THE DTC WILL BE UNSUCCESSFUL. P0300 - MULTIPLE CYLINDER MISFIRE. P0573 - BRAKE SWITCH 1 STUCK OFF."

Transmission Control Module (TCM) with new software. SYMPTOM/CONDITION: A small number of customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) stored in the PCM memory: **P0456 - EVAP System Small Leak. P1611 - Supercharger Bypass Valve Position Sensor 1 Circuit High. P0513 - Invalid Skim Key.** P0300 - Multiple Cylinder Misfire (manual transmission applications only). P1613 - Turbocharger/Supercharger Boost Pressure Sensor/Mass Air Flow Sensor Correlation. P2227 - Barometric Pressure Circuit Performance. P1217 - Active Exhaust Valve 1 Performance. P121B - Active Exhaust Valve 2 Performance. **The P0513 code is set during remote starting the vehicle and nearly simultaneously pressing the Key Fob button against the Keyless Ignition Node (KIN) causing an engine stall.**

SYMPTOM/CONDITION: A small number of customers may experience one or more of the following symptoms and/or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): P1217 - Active Exhaust Valve 1 Performance. P121B - Active Exhaust Valve 2 Performance. In addition, customers may also comment on the following: Unable to accurately increase or decrease the cruise control set speed using the resume or set buttons while the instrument cluster is set on metric units. Instead of changing vehicle speed by 1 KPH when pressing the buttons, the vehicle speed will increase approximately 1.6 KPH. Slight spark knock condition during aggressive high speed driving which may prevent the vehicle from achieving maximum top speed.

Tire Pressure Sensors Values Are Not Displayed

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

This bulletin involves replacing the fuel pump connector harness (pigtail) when replacing the fuel pump module.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous cameras image before displaying the current image.

The customer may describe that they heard about these vehicles that can be unlawfully driven away by thieves when they are able to program new key fobs through the RFHM. Software enhancement include: Update to the RFHM software to prevent hackers from programming their own key fob to the vehicle. This is intended to deter an unwanted drive off of the vehicle without the customers knowledge. Performing this RFHM update will prevent additional key fob programming and this must be communicated to the customer before performing this RFHM update. If additional keys are required by the customer after this RFHM update is performed the replacement of the RFHM is required and must be at a previous SW level.

Tire Pressure Sensors Values Are Not Displayed

contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

The customer may describe that they heard about these vehicles that can be unlawfully driven away by thieves when they are able to program new key fobs through the RFHM. Software enhancement include: Update to the RFHM software to prevent hackers from programming their own key fob to the vehicle. This is intended to deter an unwanted drive off of the vehicle without the customers knowledge. Performing this RFHM update will prevent additional key fob programming and this must be communicated to the customer before performing this RFHM update. If additional keys are required by the customer after this RFHM update is performed the replacement of the RFHM is required and must be at a previous SW level.

The customer may describe that they heard about these vehicles that can be unlawfully driven away by thieves when they are able to program new key fobs through the RFHM. Software enhancement include: Update to the RFHM software to prevent hackers from programming their own key fob to the vehicle. This is intended to deter an unwanted drive off of the vehicle without the customers knowledge. Performing this RFHM update will prevent additional key fob programming and this must be communicated to the customer before performing this RFHM update. If additional keys are required by the customer after this RFHM update is performed the replacement of the RFHM is required and must be at a previous SW level.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Tire Pressure Sensors Values Are Not Displayed

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

A small number of customers may experience a low battery condition due to the radio remaining powered up after the ignition has been turned off.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Control Module with new software or replacing the HVAC Control Module. Customers may experience the blower cutting out when HVAC blower is set to high on Manual Temperature Control (MTC) vehicles or while using high blower in manual mode on Automatic Temperature Controls (ATC) vehicles.

The customer may describe one or more of the following symptoms/conditions: ? Speakers not loud enough. ? Speakers buzz/rattle. ? Poor sound quality from speakers. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? B1474-13-Channel 5 Audio Speaker Output - Circuit Open ? B1479-13-Channel 6 Audio Speaker Output - Circuit Open

The customer may describe an audio induced buzz/rattle from the door panel or a loose door armrest pull cup. This condition may be caused by the door panel armrest pull cup attachment screw not tightened securely.

The customer may describe one or more of the following symptoms/conditions: ? Speakers not loud enough. ? Speakers buzz/rattle. ? Poor sound quality from speakers. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? B1474-13-Channel 5 Audio Speaker Output - Circuit Open ? B1479-13-Channel 6 Audio Speaker Output - Circuit Open

The customer may describe an audio induced buzz/rattle from the door panel or a loose door armrest pull cup. This condition may be caused by the door panel armrest pull cup attachment screw not tightened securely.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

The customer may describe one or more of the following symptoms/conditions: ? Speakers not loud enough. ? Speakers buzz/rattle. ? Poor sound quality from speakers. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): ? B1474-13-Channel 5 Audio Speaker Output - Circuit Open ? B1479-13-Channel 6 Audio Speaker Output - Circuit Open

The customer may describe an audio induced buzz/rattle from the door panel or a loose door armrest pull cup. This condition may be caused by the door panel armrest pull cup attachment screw not tightened securely.

performing a vehicle reconfiguration if needed. The customer may describe a condition where the low beam headlamps appear dimmer or yellow when compared to a similarly equipped vehicle.

performing a vehicle reconfiguration if needed. The customer may describe a condition where the low beam headlamps appear dimmer or yellow when compared to a similarly equipped vehicle.

Module (PCM) with updated software. During normal diagnostics a technician may find Diagnostic Trouble Code (DTC) U0140 Lost Communication With Body Control Module. Attempting to clear the DTC will be unsuccessful.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

A small number of customers may experience a low battery condition due to the radio remaining powered up after the ignition has been turned off. Also the customer may notice when the radio is set to an SiriusXM station it may switch by itself to an AM station.

Satin finishes are different from other automotive paints and need special care to maintain their appearance. Typical gloss paints use a high gloss clear-coat finish that reflects light and gives a shiny appearance. A satin finish uses a different coating that diffuses light, providing a unique ?flat? finish. Unlike a typical high gloss clear-coat, damage to the satin coating (such as scratches or wear from aggressive cleaning) cannot be polished or buffed out. Once an areais damaged or becomes shiny, the ?flat? appearance cannot be restored.

A small number of customers may experience a low battery condition due to the radio remaining powered up after the ignition has been turned off.

A small number of customers may experience a low battery condition due to the radio remaining powered up after the ignition has been turned off.

This bulletin involves selectively erasing and reprogramming HVAC Control Module with new software or replacing the HVAC Control Module. Customers may experience the blower cutting out when HVAC blower is set to high on Manual Temperature Control (MTC) vehicles or while using high blower in manual mode on Automatic Temperature Controls (ATC) vehicles.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

Customers may describe an unpleasant odor in the vehicle after driving from highway speed limits back down to city speed limits or they may also notice that the left temp door is inoperable. Updating the HVAC software will correct these conditions.

*LJ

THE POWER CONTROL MODULE UPDATED SOFTWARE. *LJ

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

not present, replacing the steering gear. Pinion Shaft Cover Retaining Washer Missing. The customer may describe loss of power steering assist.

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair.

Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead.

not present, replacing the steering gear. Pinion Shaft Cover Retaining Washer Missing. The customer may describe loss of power steering assist.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

not present, replacing the steering gear. Pinion Shaft Cover Retaining Washer Missing. The customer may describe loss of power steering assist.

A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous cameras image before displaying the current image. Navigation lost vehicle position, during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR, ? Listen? to text, will only play 1st message. Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). SirusXM station information does not update. Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. Display screen show ambient temperature as ?- - ? not normal values.Improvements: High Definition (HD) radio buffering. Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Making assist calls. App functionality and screen displays. Displays correct media, song titles and tracks. Travel Link, Points Of Interest (POI), displaying movies and favorites. Incoming calls, audio enhancements (LA, LD and LX Only). Audio for strong AM stations. VR performance. Settings can only be changed in run mode, not ACC. Notify user when messaging features are not s

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

A small number of customers may experience one or more of the following: **Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles).** Intermittently blind spot chime will not turn off (KL vehicles only). Enable High Definition (HD) feature (RA4 radios located in Canada and Mexico). Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR, ? Listen? to text will only play first message. Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). SirusXM station information does not update. Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. Display screen show ambient temperature as ?- - ? not normal values. Improvements: **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. Ability to press VR button for more than one second.**

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play first message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient tempe

transmission if you have a broken input gear. Leave a message if Kevin does not answer within 15 minutes, proceed with the repair.

A small number of customers may experience one or more of the following: Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play first message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient temperature as ?- - ? not n

transmission if you have a broken input gear. Leave a message if Kevin does not answer within 15 minutes, proceed with the repair.

Customers may experience the following:When trying to upshift using the paddle shifter on the steering, the transmission will downshift instead.

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

with the latest available software. A small number of customers may experience one or more of the following concerns. ? Malfunction Indicator Lamp (MIL) illumination with Diagnostic Trouble Code (DTC) P0734 - Gear 4 Shift Incorrect Ratio set in the TCM memory. ? Harsh or erratic 8-6 downshift during freeway driving. ? Harsh or erratic 6-4 and/or 6-3 downshift during city driving. ? Harsh or erratic upshifts while in Sport Mode. ? Less than desired downshift timing (longer time to downshift than expected). ? Less than desired downshift feel during coasting decelerations and while passing. ? Less than desired shift feel when shifting from reverse to drive or drive to reverse while the vehicle is stationary (i.e. garage shift). ? Less than desired upshift feel during normal non-aggressive driving. ? Less than desired powertrain performance at higher altitudes. ? Less than desired paddle shifter operation.

A small number of customers may experience one or more of the following: ? Blind Spot module beep or chime sound may be heard continuous (KL Only). ? Radio may keep the CAN bus network awake, causing a battery drain. ? Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. ? Not possible to set temperature in degree C using the VR (UK vehicles only). ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? Voice Recognition (VR) operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? Voice Recognition (VR) phone button may not work at times. ? Audio muted after AUX device is disconnected. ? Voice Recognition (VR) , ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Displays correct media, song titles and tracks. ? Incoming calls, audio enhancements (LA, LD and LX Only). ? Audio for strong AM stations. ? VR performance. ? Settings can only be changed in run mode, not ACC. ? Notify user wh

with the latest available software. A small number of customers may experience one or more of the following Symptom/Condition(s) and/or a Malfunction Indicator Lamp (MIL) due to an erroneous Diagnostic Trouble Code (DTC): ? P1DCD - TCM monitoring processor performance multiple clutches locked up. ? P1B13 - Park-By-Wire unintended out of park position. ? P0734 - Gear 4 Shift Incorrect Ratio set in the TCM memory. ? Harsh or erratic 8-6 downshift during freeway driving. ? Harsh or erratic 6-4 and/or 6-3 downshift during city driving. ? Harsh or erratic upshifts while in Sport Mode. ? Less than desired downshift timing (longer time to downshift than expected). ? Less than desired downshift feel during coasting decelerations and while passing. ? Less than desired shift feel when shifting from reverse to drive or drive to reverse while the vehicle is stationary (i.e. garage shift). ? Less than desired upshift feel during normal non-aggressive driving. ? Less than desired powertrain performance at higher altitudes. ? Less than desired paddle shifter operation.

A small number of customers may experience one or more of the following: ? Intermittently blind spot chime will not turn off (KL vehicles only). ? Enable High Definition (HD) feature, (RA4 radios located in Canada and Mexico). ? Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). ? The Radio may switch from SiriusXM to an AM station by itself. ? Uconnect registration always present, can not remove Uconnect account. ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? VR operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? VR phone button may not work at times. ? Audio muted after AUX device is disconnected. ? VR, ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? SirusXM station information does not update. ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Faster response time when using the Remote Service App (U.S. market only). ? Faster connection time with 911(U.S. market only). ? Keyboard improvements, in the Points Of Interest (POI) section. ? High Definition (HD) radio buffering. ? Spanish translation. ? Radio station, scroll feature. ? D

with the latest available software. A small number of customers may experience one or more of the following concerns. ? Less than desired downshift timing (longer time to downshift than expected). ? Less than desired downshift feel during coasting decelerations and while passing. ? Less than desired shift feel when shifting from reverse to drive or drive to reverse while the vehicle is stationary (i.e. garage shift). ? Less than desired upshift feel during normal non-aggressive driving. ? Less than desired powertrain performance at higher altitudes. ? Less than desired paddle shifter operation.

not present, replacing the steering gear. Pinion Shaft Cover Retaining Washer Missing. The customer may describe loss of power steering assist.

A small number of customers may experience one or more of the following: ? Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. ? Not possible to set temperature in degree C using the VR (UK vehicles only). ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? Voice Recognition (VR) operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? Voice Recognition (VR) phone button may not work at times. ? Audio muted after AUX device is disconnected. ? Voice Recognition (VR) , ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Displays correct media, song titles and tracks. ? Incoming calls, audio enhancements (LA, LD and LX Only). ? Audio for strong AM stations. ? VR performance. ? Settings can only be changed in run mode, not ACC. ? Notify user when messaging features are not supported on certain phones/devices. ? Shows direction and distance for POI when using VR.

not present, replacing the steering gear. Pinion Shaft Cover Retaining Washer Missing. The customer may describe loss of power steering assist.

Module (TCM) with the latest available software. A small number of customers may experience one or more of the following conditions. ? Less than desired upshift performance during Wide Open Throttle (WOT) accelerations. ? Less than desired overall downshift performance during coasting deceleration, braking, or while passing. ? Less than desired transmission performance during Multiple Displacement System (MDS) mode transitions. ? Less than desired light or medium throttle shift performance. In addition to the above conditions, this software release also enables the capability to capture Electronic Control Unit (ECU) data through the Uconnect Data Recording system.

A small number of customers may experience one or more of the following: ? Enable High Definition (HD) feature, (RA4 radios located in Canada and Mexico). ? Keyboard improvements, in the Points Of Interest (POI) section. ? Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). ? The Radio may switch from SiriusXM to an AM station by itself. ? Uconnect registration always present, can not remove Uconnect account. ? Teleprompter does not appear when pressing the Voice Recognition (VR) button. ? VR operation cancels while in media mode. ? Radio may display previous cameras image before displaying the current image. ? Navigation lost vehicle position, during route calculation. ? Navigation displays are missing after vehicle heading changes. ? Navigation giving incorrect guidance to exit the highway. ? FM audio may switch to AM after ignition cycle. ? Text messages appear as sender?s phone number not their name. ? VR phone button may not work at times. ? Audio muted after AUX device is disconnected. ? VR, ? Listen? to text, will only play 1st message. ? Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). ? Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). ? SirusXM station information does not update. ? Speed adjusted volume, may not work. ? AM or FM seek or tuner soft keys may be missing. ? Display screen show ambient temperature as ?- - ? not normal values. Improvements: ? High Definition (HD) radio buffering. ? Spanish translation. ? Radio station, scroll feature. ? Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). ? Making assist calls. ? App functionality and screen displays. ? Displays correct media, song titles and tracks. ? Travel

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~

A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only) The Radio may switch from SiriusXM to an AM station by itself Uconnect registration always present, can not remove Uconnect account Teleprompter does not appear when pressing the Voice Recognition (VR) button VR operation cancels while in media mode Radio may display previous cameras image before displaying the current image Navigation lost vehicle position, during route calculation Navigation displays are missing after vehicle heading changes Navigation giving incorrect guidance to exit the highway FM audio may switch to AM after ignition cycle Text messages appear as sender?s phone number not their name. VR phone button may not work at times Audio muted after AUX device is disconnected VR, ? Listen? to text, will only play 1st message Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only) SirusXM station information does not update. Speed adjusted volume, may not work AM or FM seek or tuner soft keys may be missing Display screen show ambient temperature as ?- - ? not normal values.Improvements: High Definition (HD) radio buffering. Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Making assist calls. App functionality and screen displays. Displays correct media, song titles and tracks. Travel Link, Points Of Interest (POI), displaying movies and favorites. Incoming calls, audio enhancements (LA, LD and LX Only). Audio for strong AM stations. VR performance. Settings can only be changed in run mode, not ACC.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer's concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to remedy a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality does not meet their expectations.

A small number of customers may experience one or more of the following: Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles).** Intermittently blind spot chime will not turn off (KL vehicles only). Enable High Definition (HD) feature (RA4 radios located in Canada and Mexico). Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender's phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR, Listen, to text will only play first message. Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). SirusXM station information does not update. Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. Display screen show ambient temperature as ?- - ? not normal values. Improvements: **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. Ability to press VR button for more than one second.** Faster response time when using the Remote

A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display cameras previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as senders phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR Listen to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing.

number of customers may experience one or more of the following: Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display camera?s previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as sender?s phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR ?Listen? to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing. Display screen shows ambient temperature as ?- - ? not normal values. Improvements: **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect.Improvements: **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. HVAC temperature out of sync with radio display (KL Only).** Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Displays correct media, song titles and tracks. Incoming calls, audio enhance

THIS BULLETIN INVOLVES REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM) AND TRANSMISSION CONTROL MODULE (TCM) THE LATEST AVAILABLE SOFTWARE.CUSTOMERS MAY EXPERIENCE A MALFUNCTION INDICATOR LAMP (MIL) ILLUMINATION. UPON FURTHER INVESTIGATION, THE TECHNICIAN MAY FIND ONE OR MORE OF THE FOLLOWING DIAGNOSTIC TROUBLE CODES (DTCS) STORED IN THE PCM MEMORY:

Control Module (TCM) with new software.

SYMPTOM/CONDITION: A small number of customers may experience one or more of the following: **Poor or no connection to cellular network (U.S. market only). HVAC temperature out of sync with radio display (KL vehicles).** Intermittently blind spot chime will not turn off (KL vehicles only). Enable High Definition (HD) feature (RA4 radios located in Canada and Mexico). Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. Radio may display previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as senders phone number not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR, Listen to text will only play first message. Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). SirusXM station information does not update. Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. Display screen show ambient temperature as - - not normal values.

*LJ

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

SYMPTOM/CONDITION: The customer or technician may hear a whining noise coming from the rear axle area.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

If you do not receive a return call within 15 minutes, then proceed with necessary repair.~ Please document all DTCs identified with the scan tool on the repair order narratives.~

quality issues in a timely and efficient manner

SYMPTOM/CONDITION: The customer or technician may hear a whining noise coming from the rear axle area.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

SYMPTOM/CONDITION: THE CUSTOMER OR TECHNICIAN MAY HEAR A WHINING NOISE COMING FROM THE REAR AXLE AREA."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

The customer may describe a wind noise at the left and/or right door.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

The customer may describe a wind noise at the left and/or right door.

The customer may describe a wind noise at the left and/or right door.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

The customer may experience the hood seal drooping due to cracks and tears on the hood seal.

The sunroof may also perform an auto reversal. Auto reverse feature functions properly. The customer may describe the sunroof opens by itself in the vent position or while driving.

The sunroof may also perform an auto reversal. Auto reverse feature functions properly.

The sunroof may also perform an auto reversal. Auto reverse feature functions properly.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

on a 2015 or 2016 Challenger, please contact Greg Meade on (cell) 248-770-5989.~ If no response is received within 15 minutes, then proceed with necessary repair

upper radiator hose A small number of customers may experience a slight coolant weepage underhood. After further inspection, the technician may notice coolant weeping from the upper radiator hose connection at the radiator.

on the upper radiator hose along with replacing the radiator assembly. Customers may experience a slight coolant weepage underhood. After further inspection, the technician may notice coolant weeping from the upper radiator hose connection at the radiator or the radiator itself.

upper radiator hose A small number of customers may experience a slight coolant weepage underhood. After further inspection, the technician may notice coolant weeping from the upper radiator hose area.

The customer may describe a wind noise at the left and/or right door.

The customer may describe a wind noise at the left and/or right door.

The sunroof may also perform an auto reversal. Auto reverse feature functions properly. The customer may describe the sunroof opens by itself in the vent position or while driving.

The customer may experience the hood seal drooping due to cracks and tears on the hood seal.

The sunroof may also perform an auto reversal. Auto reverse feature functions properly. SYMPTOM/CONDITION: The customer may describe the sunroof opens by itself in the vent position or while driving.

FM radio station frequencies and if applicable, replacing the inner combination tail stop backup lamp. The customer may describe a loss of audio signal or static interference on FM radio stations.

FM radio station frequencies and if applicable, replacing the inner combination tail stop backup lamp. The customer may describe a loss of audio signal or static interference on FM radio stations.

18.01.35 (BU Vehicles)

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.

(AMP) with the latest available software. The customer may describe when changing the radio tone settings (bass, mid, treble) the volume levels may be erratic. Depending where the volume is set, the volume changes may be very loud or very quiet. Example: When the volume is set to 8 and making adjustments to the tone settings, the volume can increase by 15 db. When the volume is set to 25 and making adjustments to the tone settings, there maybe no volume changes. The customer may also describe when listening with the volume set to 9 there is more bass and less mid/high. When the volume is set to 10 is less bass and more mid/high (WD,WK, W2 and W3 only).

Creating a Star case and recording the MDN and MEID with in the Star Case. The Star center will reply back with an access code that will need to be entered into the radio. The customer may notice that their Uconnect Apps do not work and they can?t register with Uconnect.

(AMP) with the latest available software. The customer may describe when changing the radio tone settings (Bass, Mid, Treble) the volume levels may be erratic. Depending where the volume is set, the volume changes maybe very loud or very little. Example: Volume set to 8 and making adjustments to the tone settings, the volume can increase by 15 db. Volume set to 25 and making adjustments to the tone settings, there maybe no volume changes.

(AMP) with the latest available software. The customer may describe when changing the radio tone settings (Bass, Mid, Treble) the volume levels may be erratic. Depending where the volume is set, the volume changes maybe very loud or very little. Example: Volume set to 8 and making adjustments to the tone settings, the volume can increase by 15 db. Volume set to 25 and making adjustments to the tone settings, there maybe no volume changes.

Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update: Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loses time. Charge Complete notification is not received (RU PHEV only). Media devices, Phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

FM radio station frequencies and if applicable, replacing the inner combination tail stop backup lamp. The customer may describe a loss of audio signal or static interference on FM radio stations.

Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

updating the radio software.

RADIO SOFTWARE REQUIRES UPDATING *CN

BULLETIN INVOLVES INSPECTING AND UPDATING RADIO SOFTWARE *CN

APPEAR WHEN VOICE RECOGNITION (VR) BUTTON IS PRESSED, BLIND SPOT CHIME INTERMITTENTLY FAILS TO TURN OFF, PREVIOUS RADIO CAMERA IMAGE IS DISPLAYED BEFORE CURRENT IMAGE. MODEL 2015 CHARGER, RAM 4500, 5500, RAM 3500, 2500, 1500 PICKUP, VIPER, CHEROKEE, CHALLENGER, GRAND CHEROKEE, DURANGO, CHRYSLER 300. *PE

120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.

Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.

the front Hub & Bearing Assy for a clicking noise occurring while turning during low speed parking lot maneuvers. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub face) with a Scotch Brite Pad or equivalent, and re-assemble.

for a clicking noise occurring while turning at low parking lot speeds. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub mounting face) with a Scotch Brite Pad or equivalent, and reassemble. When installing wheel, MUST use clicker/torque wrench, set to 110 ft-lb (150 Nm).

either front/rear or all brake rotors due to inactivity on dealer lots. The customer may describe a shake and/or vibration in the steering wheel and/or the seat while the brakes are applied. This vibration may be caused by corrosion on the brake rotors.

either front/rear or all brake rotors due to inactivity on dealer lots. The customer may describe a shake and/or vibration in the steering wheel and/or the seat while the brakes are applied. This vibration may be caused by corrosion on the brake rotors.

the front Hub & Bearing Assy for a clicking noise occurring while turning during low speed parking lot maneuvers. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub face) with a Scotch Brite Pad or equivalent, and re-assemble.

If you don't receive response within 15 minutes, please continue with normal repair procedure.

code), do NOT replace the rotor for a clicking noise occuring while turning at low parking lot speeds. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub mounting face) with a Scotch Brite Pad or equivalent, and re-assemble.~

the front Hub & Bearing Assy for a clicking noise occurring while turning during low speed parking lot maneuvers. Instead, remove front wheels and rotors and clean mating surfaces (wheel mounting face, rotor mounting faces (both sides), and hub face) with a Scotch Brite Pad or equivalent, and re-assemble.

If you don't receive response within 15 minutes, please continue with normal repair procedure.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

IF YOU DON'T RECEIVE RESPONSE WITHIN 15 MINUTES, PLEASE CONTINUE WITH NORMAL REPAIR PROCEDURE."

industry awareness regarding the use of recycled or salvage parts.

Mopar replacement axle will need the oil drained and re-filled with oil PN: 68083381AA (which contains updated friction modifier). This change was recently introduced in production to help address axle noise concerns being reported from the field while the vehicle is performing tight turning maneuvers. Failure to do so may result in a customer returning with noise complaints. NOTE: If the Mopar replacement axle serial number is past the following dates below for the corresponding axle part numbers, DO NOT DRAIN AND REFILL. The replacement axle will already have new fluid: Axle Part#: 53010668XX ? Serial # T03UG0047EXXXX Axle Part#: 53010669XX ? Serial # T03UG0047GXXXX Axle Part#: 68269917XX ? Serial # T03UG0037JXXXX Axle Part#: 05038703XX ? Serial # T03UG0047HXXXX Otherwise, perform the following repair procedure in the order given: 1. Follow standard rear axle installation procedure. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 03 - Differential and Driveline> Rear Axle> Installation>Standard Procedure>Rear Axle 2. Follow standard axle fluid drain/re-fill service procedure in TECHCONNECT. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 03 - Differential and Driveline> Rear Axle> Standard Procedure>Standard Procedure - Fluid Drain and Fill

Customers may experience the following:One or both of the vehicle?s headlamp assemblies are fogged with a light layer of condensation on the inside of the lenses.

industry awareness regarding the use of recycled or salvage parts.

Customers may experience a slight shake/vibration felt in the seat and/or floor, generated from the rear of the vehicle. Condition is most noticeable on very smooth roads, at steady-state cruising speeds 50-80 mph (80-130 kph). Upon further investigation, the concern may be narrowed down to the rear axle shafts.

A small number of customers may experience a slight noise of vibration from the rear of the vehicle. Upon further investigation, the concern may be narrowed down to the rear axle.

Bright yellow shipping covers (1) have been added during vehicle production to prevent/lessen damage to the front fascia air dam during vehicle transport (Fig. 1). If the bright yellow shipping covers are not installed on the front fascia air dam (2) (Fig. 1), this bulletin does not apply. No action is required. Fig. 1 Inspect Front Air Dam For Shipping Covers 1 - Bright Yellow Shipping Covers 2 - No Shipping Covers

Mopar replacement axle will need the oil drained and re-filled with oil PN: 68083381AA (which contains updated friction modifier). This change was recently introduced in production to help address axle noise concerns being reported from the field while the vehicle is performing tight turning maneuvers. Failure to do so may result in a customer returning with noise complaints. NOTE: If the Mopar replacement axle serial number is past the following dates below for the corresponding axle part numbers, DO NOT DRAIN AND REFILL. The replacement axle will already have new fluid: Axle Part#: 53010668XX ? Serial # T03UG0047EXXXX Axle Part#: 53010669XX ? Serial # T03UG0047GXXXX Axle Part#: 68269917XX ? Serial # T03UG0037JXXXX Axle Part#: 05038703XX ? Serial # T03UG0047HXXXX Otherwise, perform the following repair procedure in the order given: 1. Follow standard rear axle installation procedure. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 03 - Differential and Driveline> Rear Axle> Installation>Standard Procedure>Rear Axle 2. Follow standard axle fluid drain/re-fill service procedure in TECHCONNECT. Refer to the detailed service procedures available in DealerCONNECT> TechCONNECT under: Service Info> 03 - Differential and Driveline> Rear Axle> Standard Procedure>Standard Procedure - Fluid Drain and Fill

MODEL 2015 CHALLENGER, CHARGER, CHRYSLER 300. *PE UPDATED 9/30/2015 *CN

A customer may have experience one or more of the following: Backup camera screen may have static lines and/or shutters. The backup display may flash the previous image before displaying the current image. Can?t cancel compass calibration. When in compass calibration and the browse/enter button is pressed, Compass Calibration Failed will be displayed. Incorrect blind spot chime. After the audio was muted, audio doesn?t resume using Voice Recognition (VR). Information from disconnected USB flash drive is still displayed on the radio. VR session may not cancel using steering wheel switches. Back button on Integrate Center Stack (ICS) may not work at times. AM/FM is still audible when USB flash drive is plugged in. Radio screen may be black when powered up. When using steering wheel controls, the radio presets with start at preset 2 instead of preset 1. Unintentionally changing AM/FM stations when trying to scroll up or down a song list. This happens when a USB or Phone is plugged into the USB port.Improvements: iPhone functionality improvement to play music after ending calls. When SD card is used, phone lists will be properly displayed. New feature will not allow changes to settings in accessory mode.

A customer may have experience one or more of the following: ? Radio Display may freeze or go blank. ? Display shows multiple USB media song titles in the browse menu. ? Backup camera screen may have static lines and/or shutters. ? The backup display may flash the previous image before displaying the current image. ? Can?t cancel compass calibration. ? When in compass calibration and the browse/enter button is pressed, Compass Calibration Failed will be displayed. ? Incorrect blind spot chime. ? After the audio was muted, audio doesn?t resume using Voice Recognition (VR). ? Information from disconnected USB flash drive is still displayed on the radio. ? VR session may not cancel using steering wheel switches. ? Back button on Integrate Center Stack (ICS) may not work at times. ? AM/FM is still audible when USB flash drive is plugged in. ? Radio screen may be black when powered up. ? When using steering wheel controls, the radio presets with start at preset 2 instead of preset 1. ? Unintentionally changing AM/FM stations when trying to scroll up or down a song list. This happens when a USB or Phone is plugged into the USB port. Improvements: ? iPhone functionality improvement to play music after ending calls. ? When SD card is used, phone lists will be properly displayed. ? New feature will not allow changes to settings in accessory mode.

A customer may have experience one or more of the following: ? Radio Display may freeze or go blank. ? Display shows multiple USB media song titles in the browse menu. ? Backup camera screen may have static lines and/or shutters. ? The backup display may flash the previous image before displaying the current image. ? Can?t cancel compass calibration. ? When in compass calibration and the browse/enter button is pressed, Compass Calibration Failed will be displayed. ? Incorrect blind spot chime. ? After the audio was muted, audio doesn?t resume using Voice Recognition (VR). ? Information from disconnected USB flash drive is still displayed on the radio. ? VR session may not cancel using steering wheel switches. ? Back button on Integrate Center Stack (ICS) may not work at times. ? AM/FM is still audible when USB flash drive is plugged in. ? Radio screen may be black when powered up. ? When using steering wheel controls, the radio presets with start at preset 2 instead of preset 1. ? Unintentionally changing AM/FM stations when trying to scroll up or down a song list. This happens when a USB or Phone is plugged into the USB port. Improvements: ? iPhone functionality improvement to play music after ending calls. ? When SD card is used, phone lists will be properly displayed. ? New feature will not allow changes to settings in accessory mode.

A customer may have experience one or more of the following: ? Radio Display may freeze or go blank. ? Display shows multiple USB media song titles in the browse menu. ? Backup camera screen may have static lines and/or shutters. ? The backup display may flash the previous image before displaying the current image. ? Can?t cancel compass calibration. ? When in compass calibration and the browse/enter button is pressed, Compass Calibration Failed will be displayed. ? Incorrect blind spot chime. ? After the audio was muted, audio doesn?t resume using Voice Recognition (VR). ? Information from disconnected USB flash drive is still displayed on the radio. ? VR session may not cancel using steering wheel switches. ? Back button on Integrate Center Stack (ICS) may not work at times. ? AM/FM is still audible when USB flash drive is plugged in. ? Radio screen may be black when powered up. ? When using steering wheel controls, the radio presets with start at preset 2 instead of preset 1. ? Unintentionally changing AM/FM stations when trying to scroll up or down a song list. This happens when a USB or Phone is plugged into the USB port. Improvements: ? iPhone functionality improvement to play music after ending calls. ? When SD card is used, phone lists will be properly displayed. ? New feature will not allow changes to settings in accessory mode.

power steering fluid and refilling with new fluid as well as installing a new power steering fluid caution label. A small number of customers may experience an objectionable noise from the power steering system at times. In addition, they may also experience a slight loss of assist intermittently.

A customer may have experience one or more of the following: Backup camera screen may have static lines and/or shutters. The backup display may flash the previous image before displaying the current image. Can't cancel compass calibration. When in compass calibration and the browse/enter button is pressed, Compass Calibration Failed will be displayed. Incorrect blind spot chime.After the audio was muted, audio doesn't resume using Voice Recognition (VR). Information from disconnected USB flash drive is still displayed on the radio. VR session may not cancel using steering wheel switches.Back button on Integrate Center Stack (ICS) may not work at times. AM/FM is still audible when USB flash drive is plugged in. Radio screen may be black when powered up. When using steering wheel controls, the radio presets with start at preset 2 instead of preset 1. Unintentionally changing AM/FM stations when trying to scroll up or down a song list. This happens when a USB or Phone is plugged into the USB port.Improvements: iPhone functionality improvement to play music after ending calls. When SD card is used, phone lists will be properly displayed. New feature will not allow changes to settings in accessory mode.

*LJ

*LJ

Library for specifications so a suitable alternative can be used

available separate from the control arm.

available separate from the control arm.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

B)

technician an overview of the steps a customer will need to take to complete the update.

Be sure to clean wheel first to see if film/debris can be removed before ordering new wheel.~