2013 Dodge Challenger TSBs

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

exhaust system (resonator and muffler right hand assembly) cracks at or around the weld near the muffler with Model Year '13, '14, '16, and '17 Charger and Challenger 5.7L. Please call Design Release Engineer Jeff Robinson at cell phone (315) 408-6055 and send a photo of the part to him at Jeff.Robinson@fcagroup.com. If no response in 15 minutes, please proceed with repair.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. (Sales Code ERB). (LD, LX vehicles only). P0606 - Internal Control Processor.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

If the pins are missing request to add the dowel pin first and then install the transmission

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Control Module (TCM) with new software. NOTE: This bulletin applies to the following vehicles: Wrangler vehicles equipped with the WA580 Automatic Transmission (Sales Code DGJ) Challenger vehicles equipped with either the 3.6L engine (Sales Code ERB) or the 6.4L Engine (Sales Code ESH or ESG) and the WA580 Automatic Transmission (.Sales Code DGJ) Durango vehicles equipped with the 3.6L engine (Sales Code ERB) and the WA580 Automatic Transmission (Sales Code DGJ) Grand Cherokee vehicles equipped with the 6.4L engine (Sales Code ESG) for all markets except Australia (Sales Code 8AL) or the 3.6L engine (Sales Code ERB) (All Markets) and the WA580 Automatic Transmission (Sales Code DGJ). Australian vehicles equipped with the 6.4L can refer to Service Bulletin 21-010-14

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak (Sales Code ERB).** U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). P0606 - Internal Control Processor.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. NOTE: A Service Porter will be able to complete all necessary repair procedure steps with the exception of Step 7. Only in situations where Step 7 is necessary, should vehicle be dispatched to a Service Technician to clear DTCs. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

If the pins are missing request to add the dowel pin first and then install the transmission

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs):U1424-00 - Implausible Engine Torque Signal Received(2015 MY). P0456 - EVAP System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit(2014-2015 MY). U0140 - Lost Communication With Body Control Module(LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich. The following software enhancements are also available(2015 MY):Reverse gear lock-out change from 16 kph (10 mph) to 4.8 kph (3 mph)(Sales Code EZC with DEC). Change to purge vapor control calibration(Sales Code EZH with DGJ). Improvements to vehicle overspeed control(Sales Code EZH with DGJ). Calibration update to the electronic voltage regulator voltage set point(Sales Code EZH with DGJ). Additional Symptoms:Customers with a Pursuit Dodge Charger (LD) may describe an unpleasant odor in the vehicle under certain extreme ambient conditions2013-2015 MY LD with (Sales Codes EZH with AHB or AHV only). Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

Engineering is looking to gather infomation on fail mode and customer concern. If no response in 15 minutes, proceed with repair.

If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.

Module (PCM) with the latest available software. A small number of customers may experience one or more of the following symptoms or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the Powertrain Control Module (PCM): ? U0140 - Lost Communication With Body Control Module (LD and LX). ? U0140 - Lost Communication With Body Control Module (TIPM) stored in the Engine Control Module (ECM) memory (LC vehicles). ? P1621 - O2 Sensor Reference Voltage Circuit Low. ? P1622 - O2 Sensor Reference Voltage Circuit High. ? P0606 - Internal Control Processor. ? P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1. ? P0300 - Multiple Cylinder Misfire (applies only to vehicles using a block heater in ambient temperatures greater than -20F (-29C). ? Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information (LC vehicles). ? Accuracy improvements for the Automatic Oil Change Indicator (AOCI) system.

Module (PCM) with the latest available software. A small number of customers may experience one or more of the following symptoms or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more Dagnostic Trouble Codes (DTCs). ? DTC: U0140 - Lost Communication With Body Control Module (TIPM) stored in the Engine Control Module (ECM) memory (applies only to LC vehicles). ? DTC: P1621 - O2 Sensor Reference Voltage Circuit Low ? DTC: P1622 - O2 Sensor Reference Voltage Circuit High ? DTC: P0606 - Internal Control Processor ? DTC: P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 ? P0300 - Multiple Cylinder Misfire (applies only to vehicles using a block heater in ambient temperatures greater than -20F (-29C)) ? Technicians may find that the original vehicle Frequency Operated Button Integrated Key (FOBIK) does not function properly following replacement of the Wireless Ignition Node (WIN/WCM). The Secret Key information stored in the PCM may be corrupt. This update will restore the PCM?s ability to store/transfer valid Secret Key information (applies only to LC vehicles). ? Accuracy improvements for the Automatic Oil Change Indicator (AOCI) system.

Module (PCM) with the latest available software. A small number of customers may experience one or more of the following: ? Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) U0140 - Lost Communication With Body Control Module (TIPM) stored in the Engine Control Module (ECM) memory. ? For 2011 vehicles built prior to February 2, 2011, the customer may experience a condition known as ?Idle Buffeting? while the vehicle is idling. This condition can be similar to driving down the road with one rear window down and all others rolled up, causing a thumping or buffeting sound. The idle speed will be adjusted to 650 RPM to correct this condition.

Control Module (TCM) with new software. The customer may experience one or more of the following: Grand Cherokee/Durango 3.6L Engine (Sales Code ERB) ? Erratic shifting complaints while driving up steep hills or towing during hot ambient temperature conditions. ? Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. ? Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Grand Cherokee 6.4L Engine (Sales Code ESG) ? Poor acceleration or performance above 113 kph (70 mph). ? Transmission shifting while accelerating from a stop does not meet customers expectation. ? Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. ? Cannot accelerate up a steep incline or with a loaded trailer in reverse. Wrangler 3.6L Engine (Sales Code ERB) ? Erratic shifting complaints while driving up steep hills or towing during hot ambient temperature conditions. ? Hanging in gear (2nd Gear) when driving up steep hill or Towing (Rubicon ONLY). ? Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). ? Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. ? Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) - Rubicon Only. Wrangler 2.8L Engine (Sales Code ENS) Erratic while driving in Low Range (4LO). Transmission shifts in

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. NOTE: A Service Porter will be able to complete all necessary repair procedure steps with the exception of Step 7. Only in situations where Step 7 is necessary, should vehicle be dispatched to a Service Technician to clear DTCs. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit

with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. NOTE: A Service Porter will be able to complete all necessary repair procedure steps with the exception of Step 7. Only in situations where Step 7 is necessary, should vehicle be dispatched to a Service Technician to clear DTCs. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.

with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak (Sales Code ERB).** U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). P0606 - Internal Control Processor.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following DTCs have been set: **P0335 - Crankshaft Position Sensor Circuit. P2610 - PCM Internal Engine Off Timer Performance. P0456 - EVAP System Small Leak (Sales Code ERB).** U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). P0606 - Internal Control Processor.

with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).

with an additional 5 gallons of fuel, driving vehicle, then completing several start/stop cycles. The vehicles involved in this bulletin may contain factory fill fuel that exceeds allowable Driveability Index (DI) levels. NOTE: A Service Porter will be able to complete all necessary repair procedure steps with the exception of Step 7. Only in situations where Step 7 is necessary, should vehicle be dispatched to a Service Technician to clear DTCs. The MIL lamp may be illuminated and upon further investigation the Technician may find DTC P0300 - Multiple Cylinder Misfire has been set active or stored. The Technician may also notice the engine running rough on initial startup (with or without the MIL illuminated).

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

has released a new engine coolant for the 2013 model year vehicles and beyond, for all engine applications except the ones listed in the note above. This new coolant is an Organic Additive Technology (OAT) (Fig. 1). OAT coolants have a service interval of 10 years or 150,000 miles. For heavy duty truck and extreme duty cycle applications refer to the Service Information or Owner's Manual for proper maintenance schedules.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): **P0456 - Evap System Small Leak. P2610 - PCM Internal Engine Off Timer Performance. P2299 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P0335 - Crankshaft Position Sensor Circuit. (2014-2015 MY).** U0140 - Lost Communication With Body Control Module. (LC, LD and LX). P1621 - O2 Sensor Reference Voltage Circuit Low. P1622 - O2 Sensor Reference Voltage Circuit High. P0606 - Internal Control Processor. P0300 - Multiple Cylinder Misfire. P219A - Bank 1 Air-Fuel Ratio Imbalance. P219B - Bank 2 Air-Fuel Ratio Imbalance. P0307 - Cylinder 7 Misfire. P2096 - Downstream Fuel Trim System 1 Lean. P2097 - Downstream Fuel Trim System 1 Rich.

(DTC) IS SET REGARDING ENGINE OIL PRESSURE SENSOR CIRCUIT. *PE

this is normal and not a defect.

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

This bulletin involves replacing the fuel pump connector harness (pigtail) when replacing the fuel pump module.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

The customer may experience two or more speakers muting when playing certain media sources, which have frequencies of less then 20 Hz. The speakers will stay muted until the ignition key is cycled. On further inspection the technician will find speaker performance DTC's. B1460-92Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92Channel 12 Audio Speaker Output-Performance or Incorrect Operation. B221F-00Amplifier Internal.

The customer may experience two or more speakers muting when playing certain media sources, which have frequencies of less then 20 Hz. The speakers will stay muted until the ignition key is cycled. On further inspection the technician will find speaker performance DTC's. B1460-92Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92Channel 12 Audio Speaker Output-Performance or Incorrect Operation. B221F-00Amplifier Internal.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: ? P0122 - Throttle Position Sensor 1 Circuit Low. ? P0123 - Throttle Position Sensor 1 Circuit High. ? P0222 - Throttle Position Sensor 2 Circuit Low. ? P0223 - Throttle Position Sensor 2 Circuit High. ? U0140 - Lost Communication With Body Control Module (Attempting to clear this DTC will be unsuccessful).

Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or a less than desired powertrain response when operating their vehicles in high ambient temperatures. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Code (DTCs) in the PCM: ? U0140 - Lost Communication With Body Control Module (BCM) (VF, LD, LX Vehicles only). ? P0606 - Internal Control Processor.

Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more one of the following Diagnostic Trouble Codes (DTCs) set in the Powertrain Control Module (PCM): ? U0140 - Lost Communication With Body Control Module. ? P0456 - Evap System Small Leak.

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

The customer may notice that the hands free feature (Bluetooth) does not work. On further inspection Diagnostic Trouble Code (DTC), U0197 - Lost Communication With Hands Free Phone Module may be found.

occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality (examples may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the following:~ 1. Power on radio~2. Press MENU H/K~3. Press System Setup S/K~4. Press Manage HDD S/K~5. Press Display Available Space on HDD S/K~6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes~ Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. ~ Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

A customer may experience, no response or slow response to cruise control switch activations. Issues will be experienced by the customers that activate/press the switches in a very fast manner.

The customer may experience two or more speakers muting when playing certain media sources, which have frequencies of less then 20 Hz. The speakers will stay muted until the ignition key is cycled. On further inspection the technician will find speaker performance DTC's. B1460-92Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92Channel 12 Audio Speaker Output-Performance or Incorrect Operation. B221F-00Amplifier Internal.

(PCM) with the latest available software. **P0456 - EVAP System Small Leak (Sales Code ERB).** U0140 - Lost Communication With Body Control Module - (BCM) (VF, LD, LX vehicles only). P0606 - Internal Control Processor.

WITH THE LATEST AVAILABLE SOFTWARE. *LJ

*LJ

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

The Latch is now released for service under part number 68599540A$.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

fender to ensure proper retention of the replacement part can be achieved.

The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.

The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.

all clip slots in the body side and fender to ensure proper retention of the replacement part can be achieved.

fender to ensure proper retention of the replacement part can be achieved.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.

The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.

The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.

The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.

The door weatherstrip seals on all models and decklid weatherstrip seals on 300's and Chargers have been contaminated during part processing and it will create an odor in the passenger compartment.

Control Module (TCM) with new software.

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

System (ABS) module and Totally Integrated Power Module (TIPM). Also sending the cluster to the exchange center for updating. The customer may note that the launch control feature is missing. Updating the modules will add this feature to the vehicle.

(ABS) module, Cluster and Totally Integrated Power Module (TIPM), if required. The customer may note that the launch control feature is missing.

Control Module (TCM) with new software. The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Grand Cherokee/Durango Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer.6.4L Grand Cherokee Poor acceleration or performance above 113 kph (70 mph). Transmission shifting while accelerating from a stop does not meet customers expectation. Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. Cannot accelerate up a steep incline or with a loaded trailer in reverse.3.6L Wrangler Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Rubicon Only.2.8L Wrangler Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) Transmission shifting while accelerating from a stop does not meet customers expectation. Poor vehicle performance in Drive Poor vehicle performance in Auto Stick Mode. Rubicon Only.3.6L Challenger Transmission shifting does not meet customers expectation while towing a loaded

System (ABS) module and Totally Integrated Power Module (TIPM). Also sending the cluster to the exchange center for updating. The customer may note that the launch control feature is missing. Updating the modules will add this feature to the vehicle.

(ABS) module, Cluster and Totally Integrated Power Module (TIPM), if required. The customer may note that the launch control feature is missing.

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

The following Transmission Control Module (TCM) calibration improvements are available for vehicles equipped with WA580 Automatic Transmission (Sales Code DGJ).3.6L Grand Cherokee/Durango Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >58 kph (36 mph) - All Markets. Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer.6.4L Grand Cherokee. Poor acceleration or performance above 113 kph (70 mph).Transmission shifting while accelerating from a stop does not meet customers expectation. Harsh shifting during acceleration with moderate accelerator pedal and then lifting off the accelerator pedal. Cannot accelerate up a steep incline or with a loaded trailer in reverse.3.6L Wrangler Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F). Poor performance and/or poor powertrain response when trying to accelerate from speeds >48 kph (30 mph) - Japan/Taiwan/China vehicles only. Rubicon Only.2.8L Wrangler Transmission shifts inconsistently (gear hunting) when driving up/down steep hills or when towing a trailer. Delayed Drive to Reverse shift engagement when the transfer case is in Low Range (4LO) Transmission shifting while accelerating from a stop does not meet customers expectation. Poor vehicle performance in Drive Poor vehicle performance in Auto Stick Mode. Rubicon Only.3.6L Challenger Transmission shifting does not meet customers expectation while towing a loaded trailer in high ambients (>32C/90F).

System (ABS) module and Totally Integrated Power Module (TIPM). Also sending the cluster to the exchange center for updating. The customer may note that the launch control feature is missing. Updating the modules will add this feature to the vehicle.

(ABS) module, Cluster and Totally Integrated Power Module (TIPM), if required. The customer may note that the launch control feature is missing.

*CN

The customer may indicate that there is no audio sound and/or radio is muted. This may happen when the audio is at a higher volume. The audio system will mute and remains ?muted? until the key is cycled. The audio system may defaults to surround sound after a key cycle. On further inspection one or more of the following DTCs may be found: B1460-92 Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92 Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92 Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92 Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92 Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92 Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92 Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92 Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92 Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92 Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92 Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92 Channel 12 Audio Speaker Output-Performance or Incorrect Operation.

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.

The customer may notice a poor audio quality. This condition may happen when the audio volume is at a mid to high output.

The customer may indicate that there is no audio sound and/or radio is muted. This may happen when the audio is at a higher volume. The audio system will mute and remains ?muted? until the key is cycled. The audio system may defaults to surround sound after a key cycle. On further inspection one or more of the following DTCs may be found: B1460-92 Channel 1 Audio Speaker Output-Performance or Incorrect Operation. B1465-92 Channel 2 Audio Speaker Output-Performance or Incorrect Operation. B146A-92 Channel 3 Audio Speaker Output-Performance or Incorrect Operation. B146F-92 Channel 4 Audio Speaker Output-Performance or Incorrect Operation. B1474-92 Channel 5 Audio Speaker Output-Performance or Incorrect Operation. B1479-92 Channel 6 Audio Speaker Output-Performance or Incorrect Operation. B147E-92 Channel 7 Audio Speaker Output-Performance or Incorrect Operation. B1483-92 Channel 8 Audio Speaker Output-Performance or Incorrect Operation. B14B9-92 Channel 9 Audio Speaker Output-Performance or Incorrect Operation. B14BE-92 Channel 10 Audio Speaker Output-Performance or Incorrect Operation. B14C3-92 Channel 11 Audio Speaker Output-Performance or Incorrect Operation. B14C8-92 Channel 12 Audio Speaker Output-Performance or Incorrect Operation.

The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).

The customer may experience one or more of the following conditions. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

A customer may experience, no response from or inoperative radio display.

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

The customer may experience up to 1mm(1/32?) fore/aft movement of the driver and/or passenger seat during acceleration and/or braking.

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

The customer may experience up to 1mm(1/32?) fore/aft movement of the driver and/or passenger seat during acceleration and/or braking.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

Switch-Paddle Up Audio RT. Issue Description: When traveling over bumpy roads, a high pitched ringing/bell sound may come from the left or right paddle switch's in the steering wheel. If this noise is heard, replace both Left and Right Paddle switch.

Library for specifications so a suitable alternative can be used

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

pivot bushings.

pivot bushings.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

B)