2010 Dodge Challenger TSBs

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

If the pins are missing request to add the dowel pin first and then install the transmission

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: Performance derate above 55 MPH when accelerating at wide open throttle immediately following engine start-up.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

If the pins are missing request to add the dowel pin first and then install the transmission

involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: Performance derate above 55 MPH when accelerating at wide open throttle immediately following engine start-up.

Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: Performance derate above 55 MPH when accelerating at wide open throttle immediately following engine start-up.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

WHICH COULD CAUSE THE ENGINE TIMING CHAIN TO BREAK. 06/06/2014*LJ

DUE TO AN ENGINE FRACTURED TIMING CHAIN GUIDE, THE TIMING CHAIN IN ENGINE WILL BREAK AND WOULD RESULT IN SEVERE DAMAGE TO THE ENGINE. MODEL 2009-2012 CHALLENGER, CHARGER, 300. *PE

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

This bulletin involves replacing the fuel pump connector harness (pigtail) when replacing the fuel pump module.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) U0401-00 - Implausible Data Received From ECM/PCM. This software update also has improvements for fuel pump relay cycling during remote starts.

PROCEDURE ON SELECTIVELY ERASING AND REPROGRAMMING POWERTRAIN CONTROL MODULE *CN

THIS CAN BE CORRECTED WITH A SOFTWARE UPDATE IN THE POWERTRAIN CONTROL MODULE (PCM). *KB

STEERING WHEEL MOUNTED AUDIO CONTROL SWITCHES AND A RELATED WIRING HARNESS MUST BE INSTALLED. CSC LETTER WAS REC'D. *PE

COMPLAINTS OF MIL ILLUMINATION. UPON INVESTIGATION THE TECHNICIAN MAY FIND THAT P0133-02 SENSOR 1/1 SLOW RESPONSE AND/OR P0153-02 SENSOR 2/1 SLOW RESPONSE HAS BEEN SET. *PE

semi and full synthetic oils.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

Customers may experience a clunk, squeak, or similar noise heard from center console area while shifting.

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

*RM

The customer may experience after the vehicle is turned off a slow thumping noise coming from the subwoofer. This may happen only a few times or last until the next key cycle. This is caused by the amplifier waking up and then going back to sleep.

The customer may experience after the vehicle is turned off a slow thumping noise coming from the subwoofer. This may happen only a few times or last until the next key cycle. This is caused by the amplifier waking up and then going back to sleep.

The customer may experience after the vehicle is turned off a slow thumping noise coming from the subwoofer. This may happen only a few times or last until the next key cycle. This is caused by the amplifier waking up and then going back to sleep.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

Library for specifications so a suitable alternative can be used