2005 Dodge Caravan TSBs

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

Some customers may experience an engine stumble or stall condition which occurs immediately after filling the fuel tank. The integral multi-functional control valve may stick allowing liquid fuel to enter the evaporative emissions system causing a rich fuel condition when the purge system is initiated.

SYSTEMS, TURNING OFF OR UNANTICIPATED ILLUMINATION, FLICKERING OR DIMMING OF EXTERIOR AND/OR INTERIOR LIGHT WITH ENGINE IS AT IDLE SPEED, OR SINGLE LAMP IN EITHER INTERIOR OR EXTERIOR LIGHTING SYSTEM. MODELS 2005-2006 TOWN & COUNTRY, VOYAGER, CARAVAN AND GRAND CARAVAN. *PE

*KB

*TT

*TT

GPOP - ISSUE REVIEW SYSTEM. *TT

*SC

RAPID RESPONSE TRANSMITTAL. *TT

*TT

*TT

*TT

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

*TT

*AK

*TT

*MJ

*MJ *TT

RAPID RESPONSE TRANSMITTAL. *TT

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

AND ALLOW WATER TO ENTER INTO THE SENSOR. THESE SENSORS WERE ADDED TO ENHANCE THE PERFORMANCE OF THE VEHICLE'S AIRBAG SYSTEM; HOWEVER, A CRACKED SENSOR MAY NOT OPERATE PROPERLY IN A FRONTAL CRASH. A CRACKED SENSOR CAN ALSO ILLUMINATE THE AIRBAG WARNING LIGHT. RIGHT AND LEFT SUPPLEMENTAL FRONT AIRBAG SENSORS MUST BE REPLACED AND THE SENSOR WIRING HARNESS CONNECTORS MUST BE INSPECTED AND REPLACED, IF NECESSARY. CSC LETTER WAS REC'D. *PE

*KB

*KB

TO INCLUDE 2006 CHRYSLER TOWN AND COUNTRY AND 300/TOURING. *TT

MALFUNCTION INDICATOR LAMP ILLUMINATION DIAGNOSTIC TROUBLE CODES (DTC) P0135 - O2 SENSOR 1/1 HEATER PERFORMANCE. *SC

*SC

2005 CHRYSLER VOYAGER. *SC

*TT

*TT

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

ILLUMINATE WHILE PARK LAMPS REMAIN ILLUMNATED AFTER SWITCHING ON. MODELS 2005-2006 TOWN & COUNTRY, VOYAGER, GRAND CARAVAN, CARAVAN, GRAND VOYAGER. *PE

FLASH. *TT

*TT THIS BULLETIN SUPERSEDES BULLETIN 18-035-04, DATED SEPTEMBER 1, 2004. *TT

*TT

*KB

*TT

*TT

*TT

*TT

*TT

*SC

*TT *SC

*TT

*TT

*EH

ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE WITH NEW SOFTWARE IS NECESSARY. *KB

SERVICE ACTION #04-011. 2005 CHRYSLER PACIFICA ALSO INCLUDED. *TT

*TT AND/OR TRANSFER GEAR WHINE SOUND BETWEEN 20 MPH AND 65 MPH, EITHER ACCELERATING OR DECELERATING. *TT

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

Issue Description: Do not replace the entire seat belt if the seat belt web stop button is missing or damaged.~Belt Web Button:~ 1D1 - Light Graystone - 05093280AB Belt Web Button~1D5 - Medium Slate Gray - 05093280AB Belt Web Button~1DA - Pastel Slate Gray - 05093280AB Belt Web Button~1J3 - Medium Khaki - 05093283AB Belt Web Button~ZJ3 - Medium Khaki - 05093283AB Belt Web Button~1L2 - Light Natural Beige - 05114207AA Belt Web Button~BD1 - Light Graystone - 05093280AB Belt Web Button~ BD5 - Medium Slate Grey - 05093280AB Belt Web Button~ BDA - Pastel Slate Gray - 05093280AB Belt Web Button~ ZP7 - Deep Seamist Green - 05093280AB Belt Web Button~ 5JB571D1A$, 5JB571D5A$, 5JB571J3A$, 5JX141D1A$, 5JX141D5A$, 5JX141DVA$, 5JX141J3A$, 5JX14ZJ3A$, 1EY841D1A$, 1EY841D5A$, 1EY841J3A$, 1EY851D1A$, EY851D5A$, 1EY851J3A$ use the following mini Belt Web Buttons:~1D1 - Light Graystone - 05093285AB Mini Belt Web Button~1D5 - Medium Slate Gray - 05093285AB Mini Belt Web Button~1DV - Slate Gray - 05093285AB Mini Belt Web Button~1J3 - Medium Khaki - 05093286AB Mini Belt Web Button~ZJ3 - Medium Khaki - 05093286AB Mini Belt Web Button~ Position the button as originally installed, or use the opposite side as reference.~ Web Button Location CS:~Front Driver O/B: 690 +/- 10 mm~Front Passenger O/B: 435 +/- 10 mm~Rear O/B: 435 +/- 10 mm~Rear Center: 290 +/- 10 mm~Rear Center Mini: 854 +/- 10 mm~ Web Button Location RG/RS SWB:~Front O/B: 550 +/- 6 mm~2nd Row O/B: 558 +/- 6 mm~ 3rd Row O/B: 584 +/- 6 mm~Web Button Location RG/RS LWB:~Front O/B: 550 +/- 6 mm~ 2nd Row O/B: 518 +/- 6 mm (Exception 52029368A$, 04680197A$: 690 +/- 6 mm)~ 3rd Row O/B: 585 +/- 6 mm (Exception 1CK35BD1A$, 1CK35BD5A$, 1CK35ZJ3A$, 52029369A$, 52029370A$: 434 +/-6 mm)~ Apply a small dot of Bond-All Gel, p/n 04467709, around the backside hole of the female button. Press the female button over the post of the male that is sticking through the rearwar

*KB

*KB UPDATED 10/26/07. *NJ

*EH

*KB

*TT

*TT

*TT