2004 Dodge Caravan TSBs

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

*KB

*KB

TO INCLUDE 2006 CHRYSLER TOWN AND COUNTRY AND 300/TOURING. *TT

*SC

*TT

C30. *TT

2004 MODELS INCLUDED. *TT

*TT

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

The supplier is currently working on a functional replacement. Currently, for customer satisfaction, the immobilizer blade key (no integrated FOB) P/N 05018689AA can be offered to the customer as an alternative option. For any details please contact FCA Engineering: Cell (248) 408-9068 Boris Prishkolnik

attaching rivet and an instruction sheet are now available as a kit. If the insulator requires replacement lease order 68253099AA. Note: Insulator color is not relevant for service

Some customers may experience an engine stumble or stall condition which occurs immediately after filling the fuel tank. The integral multi-functional control valve may stick allowing liquid fuel to enter the evaporative emissions system causing a rich fuel condition when the purge system is initiated.

*KB

GPOP - ISSUE REVIEW SYSTEM. *TT

*SC

*TT

*TT

*TT

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

*TT

2004 CHRYSLER AND PLYMOUTH VOYAGER DISCONTINUED. *TT

perform the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Remove hex nut and the top flared fitting on the radiator tank.~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.~ 5. Install the top flared fitting by hand, then torque the fitting to 235 +/- 15 Lb-In.~ 6. Install the hex nut and torque to 100 +/- 10 Lb-In.~ 7. Repeat steps 2-6 for bottom flared fitting.~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~

perform the following before replacing the radiator/cooler:~ 1. Remove both of the transmission lines from the cooler?s top/bottom flared fittings on the radiator. ~ 2. Remove hex nut and the top flared fitting on the radiator tank.~ 3. Using a wire brush and gasket remover, clean off the old sealant on the smaller threaded portion of the flared fitting. Do the same for the threads on the trans oil cooler.~ 4. Apply a new application of Mopar PN 04318032 to the flared fitting, leaving the first threads free for ease of engagement.~ 5. Install the top flared fitting by hand, then torque the fitting to 235 +/- 15 Lb-In.~ 6. Install the hex nut and torque to 100 +/- 10 Lb-In.~ 7. Repeat steps 2-6 for bottom flared fitting.~ 8. Reinstall transmission line per normal installation procedures and ensure correct fluid level.~

*TT AND/OR TRANSFER GEAR WHINE SOUND BETWEEN 20 MPH AND 65 MPH, EITHER ACCELERATING OR DECELERATING. *TT

*TT

VARIOUS MODELS INCLUDING THE 2004 RAM TRUCK, DURANGO, SEBRING CONVERTIBLE, CHEROKEE, VISION, NEON, AND VOYAGER. *TT *SC

*KB

*TT

*TT

*TT

*TT

*SC

*TT

*MJ *EH

*TT *MJ

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

*TT

*TT

*KB UPDATED 10/26/07. *NJ

*EH

*TT THIS BULLETIN SUPERSEDES BULLETIN 23-010-04 DATED 04-29-04. *TT

LAMPS FLASH WITH RKE UNLOCK INOPERATIVE. 2004 CHRYSLER AND PLYMOUTH VOYAGER MODELS DISCONTINUED. *TT

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

Issue Description: Do not replace the entire seat belt if the seat belt web stop button is missing or damaged.~Belt Web Button:~ 1D1 - Light Graystone - 05093280AB Belt Web Button~1D5 - Medium Slate Gray - 05093280AB Belt Web Button~1DA - Pastel Slate Gray - 05093280AB Belt Web Button~1J3 - Medium Khaki - 05093283AB Belt Web Button~ZJ3 - Medium Khaki - 05093283AB Belt Web Button~1L2 - Light Natural Beige - 05114207AA Belt Web Button~BD1 - Light Graystone - 05093280AB Belt Web Button~ BD5 - Medium Slate Grey - 05093280AB Belt Web Button~ BDA - Pastel Slate Gray - 05093280AB Belt Web Button~ ZP7 - Deep Seamist Green - 05093280AB Belt Web Button~ 5JB571D1A$, 5JB571D5A$, 5JB571J3A$, 5JX141D1A$, 5JX141D5A$, 5JX141DVA$, 5JX141J3A$, 5JX14ZJ3A$, 1EY841D1A$, 1EY841D5A$, 1EY841J3A$, 1EY851D1A$, EY851D5A$, 1EY851J3A$ use the following mini Belt Web Buttons:~1D1 - Light Graystone - 05093285AB Mini Belt Web Button~1D5 - Medium Slate Gray - 05093285AB Mini Belt Web Button~1DV - Slate Gray - 05093285AB Mini Belt Web Button~1J3 - Medium Khaki - 05093286AB Mini Belt Web Button~ZJ3 - Medium Khaki - 05093286AB Mini Belt Web Button~ Position the button as originally installed, or use the opposite side as reference.~ Web Button Location CS:~Front Driver O/B: 690 +/- 10 mm~Front Passenger O/B: 435 +/- 10 mm~Rear O/B: 435 +/- 10 mm~Rear Center: 290 +/- 10 mm~Rear Center Mini: 854 +/- 10 mm~ Web Button Location RG/RS SWB:~Front O/B: 550 +/- 6 mm~2nd Row O/B: 558 +/- 6 mm~ 3rd Row O/B: 584 +/- 6 mm~Web Button Location RG/RS LWB:~Front O/B: 550 +/- 6 mm~ 2nd Row O/B: 518 +/- 6 mm (Exception 52029368A$, 04680197A$: 690 +/- 6 mm)~ 3rd Row O/B: 585 +/- 6 mm (Exception 1CK35BD1A$, 1CK35BD5A$, 1CK35ZJ3A$, 52029369A$, 52029370A$: 434 +/-6 mm)~ Apply a small dot of Bond-All Gel, p/n 04467709, around the backside hole of the female button. Press the female button over the post of the male that is sticking through the rearwar

*KB

*TT

2004 VOYAGER INCLUDED. *TT