2008 Dodge Avenger TSBs

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

not replace the intake manifold for a short runner valve (SRV) fault (P1004 / P2008 / P2016 / P2017) or for a manifold tuning valve (MTV) fault (P1005 / P2077 / P2078). Instead follow the service procedure to investigate P codes associated with diagnosis of the SRV or MTV, then cycle the actuator using a diagnostic tool and verify that the PWM output is 50 (+ 2%) de-energized and 80 (+ 2 %) energized. If no problems observed, then idle the vehicle and verify the correct PWM output (50 + 2% PWM). Replace the actuator if you do not get the desired output. Issue 2~ If the SRV actuator or intake manifold is being replaced for a P1004 Short Runner Valve Performance fault code and the vehicle was built prior to 2/5/07 , technicians must complete the module reflash and verification test per TSB 18-003-07 REV. A to ensure the parts need to be replaced. Please reference TSB 18-003-07 REV. A for specific details on the procedure.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

*NJ

*NJ

*NJ

VEHICELS EQUIPPED WITH A 2.4L PZEV ENGINE. *NJ

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

The customer may describe the following conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality

micro switches and/or position sensors, please refer to the updated diagnostic tests for your specific DTC's. A physical check of the switch (resistance check, does it click, is the lever sticky, is the return spring present) will verify or eliminate that switch as the root cause of the vehicle's concern. RRT 07-025 only applies to vehicles built on or before June 22, 2007.~

THIS BULLETIN INVOLVES SELECTIVELY ERASING AND REPROGRAMMING THE POWERTRAIN CONTROL MODULE (PCM). *PE

This bulletin involves replacing the clutch and damper assembly. The customer may experience a vibration feeling as they accelerate from a stop or accelerating while rolling at slow speeds. This condition could be caused by the damper and clutch.

This bulletin involves replacing the clutch and damper assembly. The customer may experience a vibration feeling as they accelerate from a stop or accelerating while rolling at slow speeds. This condition could be caused by the damper and clutch.

This bulletin involves replacing the clutch and damper assembly. The customer may experience a vibration feeling as they accelerate from a stop or accelerating while rolling at slow speeds. This condition could be caused by the damper and clutch.

AUTOMATIC TRANSMISSION SHIFT LEVER INTERLOCK SPRING. TRANSMISSION GEAR SHIFT LEVER INTERLOCK SPRING RETAINER HOOK ON VEHICLES MAY BREAK. A BROKEN INTERLOCK SPRING RETAINER HOOK WILL RESULT IN THE INABILITY TO MOVE THE GEAR SHIFT LEVER OUT OF THE PARK POSITION. CSC LETTER WAS REC'D. *PE

*NJ

RINGS TOGETHER AS A SET IF A DE-BONDING CONDITION IS FOUND. *NJ

*NJ

TOTALLY INTEGRATED POWER MODULE (TIPM) WAS INADVERTANTLY PROGRAMMED WITH SOFTWARE THAT MAY PREVENT THE TRANSMISSION FROM SHIFTING PROPERLY. *KB

*KB

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

CERTAIN VEHICLES WERE SHIPPED WITH THE INCORRECT TORQUE ON THE DECKLID LATCH MOUNTING BOLTS AND WILL REQUIRE RE-TORQUE TO 10NM (88.50 IN LB). *PE

new guideline states that the tether anchor can be used with a seatbelt to install a child restraint up to the recommended weight limit of the child restraint.

new guideline states that the tether anchor can be used with a seatbelt to install a child restraint up to the recommended weight limit of the child restraint.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

conditions: A complete loss of UConnect operation. A complete loss of Voice Recognition functionality

CUSTOMER SATISFACTION NOTIFICATION H11; RADIO SOFTWARE UPDATE. THIS NOTIFICATION APPLIES ONLY TO VEHICLES EQUIPPED WITH A MYGIG RADIO (SALES CODE RER WITH NAVIGATION SYSTEM OR REN WITHOUT NAVIGATION SYSTEM). CSC WAS RECEIVED. *PE

*NJ

*NJ

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

*NJ

THE WARRANTY BOOK ON CERTAIN VEHICLES MAY CONTAIN ERRORS OR MAY BE MISSING INFORMATION REGARDING THE COPONENTS COVERED BY THE CALIFORNIA EMISSIONS WARRANTY. DODGE-CARAVAN/GRAND CARAVAN, CHARGE/CHARGER SRT8, MAGNUM/MAGNUM SRT8, VIPER, AVENGER, NITRO, CHALLENGER/CHALLENGER SRT8, DURANGO/DURANGO HYBRID, JOURNEY, RAM 2500/3500, CALIBER/CALIBER SRT4; JEEP COMMANDER, GRAND CHEROKEE/GRAND CHEROKEESRT8, COMPASS, PATROIT, LIBERTY; CHRYSLER TOWN&COUNTRY, PACIFICA, 300 SRT8, PTCRUISER, SEBRING/SEBRING CONV., ASPEN/ASPEN HYBRID.

INCLUDES MY09 TOWN&COUNTRY; VOYAGER AND CARAVAN. *PE

*KB