2022 Coachmen Sportscoach TSBs
9 Technical Service Bulletins across 5 categories
Steering
3 bulletinsAccording to DTNA Recall 23V259: "On the affected vehicles, the steer axle tie rod castle nut cotter pin may be missing,...
Read full bulletin
allowing the steering arm to detach. This could lead to a loss of steering response and a lack of direction control, increasing the risk of a crash. The driver may experience some additional free-play in the steering and/or feel an improper steering alignment."
According to DTNA Recall FL970/23V238: "The steer axle tie rod castle nut cotter-pin on the affected vehicles may be missing.
Read full bulletin
This may cause the castle nut to back off, which might allow taper-end to displace from the steering arm. This could lead to a loss of steering response and a lack of direction control, potentially increasing the risk of a crash."
Per DTNA recall FL888 21V369 and 21V370; The tie rod clamp may be loose due to the supplied lock nuts being over-crimped.
Read full bulletin
This can cause thread galling of the bolt and nut during installation. When galling occurs, it is possible that assembly torque may be achieved but the clamp is still loose. The tie rod clamp being loose could lead to the threaded tie rod ends becoming loose and eventual steering loss if the rod end pulls out of the tie rod, or the tube is broken due to vibration of the loose joint, creating the risk of crash.
Engine
2 bulletinsAs per Lippert's TSB 85-001-2022: There is a potential for some of the Gen1 jack legs on motorized units to bend or...
Read full bulletin
deform under extreme side loads.
Damage to the tires valve stem may lead to loss of air pressure, which, if unnoticed, could lead to a flat tire or on dual-wheels an overloaded tire.
Read full bulletin
In extreme situations, rapid loss of tire pressure could increase the risk of a crash. Operators may identify an audible rattling noise from the stem extension rubbing against the wheel opening while driving. Visual inspection during inspection or during maintenance may reveal stabilizer is dislocated, damage to the stem extension, or the rim, and low tire pressure of the inner tire.
Infotainment
2 bulletinsPer DTNA Recall 22V379 - On certain vehicles and under certain circumstances, the tire pressure monitoring system (TPMS)...
Read full bulletin
may display incorrect information such as maximum temperature and tire pressure, and/or a message that the tires are under or over-inflated. The TPMS controller will be updated with new software, and certain units will require a longer antenna-mounting bracket to extend the rear antenna downward.
Per Daimler Truck North America's Campaign Number "SF644A-C": On certain vehicles and under certain circumstances, the...
Read full bulletin
tire pressure monitoring system (TPMS) may display incorrect information such as maximum temperature and tire pressure, and/or a message that the tires are under or over-inflated. The TPMS controller will be updated with new software, and certain units will require a longer antenna-mounting bracket to extend the rear antenna downward.
HVAC & Climate
1 bulletinAccording to a Furrion TSB "TB-220919": Irregular cooling performance has been reported on the identified refrigerators.
Read full bulletin
The refrigerator compressor has been found to stop working and requires a hard reset by disconnecting power to reset cooling operation. On occasion, disconnecting power does not reset operation and the refrigerator requires service replacement of the control boards. This TSB may not be applicable for some vehicles.
Electrical
1 bulletinDaimler Trucks North America LLC (DTNA), on behalf of its wholly owned subsidiary, Freightliner Custom Chassis...
Read full bulletin
Corporation, is initiating Field Service Campaign SF637A to modify specific model year 2021 Freightliner Custom Chassis manufactured September 17, 2019 through April 7, 2021. In a low voltage condition, the IP display may not come on when turning on ignition leaving drivers without a functioning instrument panel. This would only occur at startup and the instrument panel would function again if the key is cycled with normal voltage. The software will be updated to resolve the issue.