2023 Chrysler Voyager TSBs

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P152F - Engine Hood Switch 2 / Engine Hood Switch 1 Correlation.** Customers may experience one of the following: **A low battery state of charge and/or dead battery. Engine Stop/Start inoperable.** Vehicle may enter Auto Park Mode during an Engine Stop Start (ESS) event. The driver will be notified that the vehicle is entering Auto Park Mode by the blinking D on the shifter for three blinks and then automatically shifting into Park. NOTE: **To shift out of Park, the driver will have to press down on the brake pedal and cycle the ignition back to START, and move the shifter into the desired position.** This bulletin involves reprogramming the PCM with the latest available software.

This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.

There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC): - P152E Engine -Hood Switch 2 Circuit High. - DTC P152F Customers may also experience: - Start/Stop system warning light. - Start/Stop inoperable. - Remote start inoperable. Diagnosis: - Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other than the one listed are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. - If any vehicle exhibits any of the symptoms listed above in the customer symptom section, perform the Repair Procedure. - Special Tools/Equipment: wiTECH or equivalent. Repair Procedure: 1. Open the hood and locate the hood switch 2. Push in on the two locking tabs and pull them out. 3. Disconnect the wire connector from the switch. 4. Connect the wires to the same hood switch. 5. Push the switch back into the hold until both lock tab are engaged. 6. Clear all DTCs that may have been set in any module during this repair procedure. 7. In case the P152F/P152E DTCs persist, repeat the procedure with a new/spare/known good switch and repeat steps 5 and 6. 8. Replace switch installed during previous step for the original switch of the vehicle. If DTCs P152F/P152E are not present, leave the original switch installed and do not document the change of the switch in the repair process/narrative.

Powertrain Mounting Neutralization Procedure. Discussion: Service information is in the process of being updated to include powertrain mount installation best practices. The new procedure will neutralize the mounts to lessen or remove unwanted mount tension that can lead to vibration complaints.

Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: Rough idle. Valvetrain noise. "

Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.

Diagnostic Trouble Code (DTC) U0485 - Implausible Data Received Set. Radio reset (Rearview camera functions normally). Voice Recognition (VR) inoperable. Wireless CarPlay inoperable. Audio sources inoperable. Display switches to Nav on VR prompt. Vehicle Positioning (Lat/Long) inoperable. Surround View Camera inoperable (Rearview camera functions normally). Unable to exit FamCam. Audio Repetition inoperable. Electric vehicle pages inoperable. Translated text is incorrect. Profile avatar changes in Valet Mode. Display does not return to idle mode after call. Dynamic rear view camera guidelines inoperable (Rearview camera functions normally). FOTA popup wont dismiss. Ambient Lights Setting inoperable. Call Status on after all ended Favorites available in valet mode. SXMT Favorites inoperable. Tutorial App inoperable. Audio Repetition stops during incoming calls. Unable to connect second device. Unable to exit Seat Comfort popup. Call does not end on the Instrument Panel Cluster (IPC). Seat Comfort graphic incorrect. Headphone button for front passenger display inoperable. Schedule update inoperable. USB media source inoperable on front passenger display. SXMT inoperable. Wireless Android Auto inoperable. Media sources duplicated. Audio unmuted at door close. Radio freeze (Rearview camera functions normally). Radio input lagging. Navigation active with no active route. Scheduled cabin cooling inoperable. Incorrect phone repetition displayed. Navigation routing inoperable. Unable to exit Electric Vehicle Pages. Comfort softkeys incorrect. Comfort graphic overlap. Unable to change audio sources. Audio sources unavailable after profile switch. No incoming call popup on Uconnect phone. FamCam image in black and white. SOS call status banner remains after call ended. Press and hold inoperable on comfort temperature slider. Setting preferences will not return to default. Display input lagging after CarPlay is connected. Changing to unselected audio source. Setting preferences not saved on correct profile. Translation error in Portuguese. Memory seats not saved on correct profile. Audio loss. Incorrect keyboard in Japanese. SXMT channel art incorrect. Rear Seat Entertainment (RSE) audio overlap. European Media Source (DAB) available on North America vehicles. Black screen (Rearview camera functions normally). Unable to delete profile. Assist call inoperable. Unable to navigate menu with ongoing SOS call. This update also includes the following software enhancements: Radio Software stability issues and moving to new U-branch software for core improvement This bulletin involves inspecting the software level and updating the software to U29.28. "

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

Check DTCs in DCM and check the component they are pointing to, depending on the case follow the procedure below: If there are DTCs related with power sliding door switch, sliding door latch or handle follow the next procedure: - The sliding door should be put into manual operation mode. If the door still opens and closes manually, door modules should be reset, if the DTC's don't go stored or door/body module resets have not solved the issue, then replace the latch. If in manual operation mode the door does not open, replace the latch. In the case of window inoperation, follow the next procedure: - Check wiring between motor and Door Control module, if it is in good state, check motor, and if needed replace it. If wiring is well seated, and the motor is in good state, reset module and perform window calibration, if DTCs don't go stored or the window continue not working, replace the Door Control Module.

There may be Diagnostic Trouble Codes (DTCs) present. "

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures."

Customer complaints may include a noise coming from under de hood described as a squeal, screech, squeak, chirp or "belt related" noise and/or noisy tensioner/pulley. Please check Service Library for any STAR Online publications that may apply. Note: If it is found that the pulleys and/or tensioners are to blame for the noise please use an stethoscope or similar tool to determine the origin of the noise and include it in the narrative.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present.

INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.

published diagnostic information for this DTC to ensure all module connections are secure. Please check all the connections at BCM from other modules that could potentially report a loss of communication with the BCM and ensure that they are fully seated as per diagnostic information. Some affected modules may include : HVAC-R, Radio, Amplifier (AMP) & Premium, HVAC, ORC, LBSS, RBSS, PCM, EPS, MSMP, AHLM, PTS/PAM, ICS, ESM, RF Hub, RCCC, MSMD, ANC, PLGM, PSDML, DMRL, DMRR, PSDMR, TBM, PDM(DMFL/R), DDM(DMFL/R), DTCM, OCM, ACC, FFCM, DSM, CVPM, VRM, SCCM, FSM, CSWM. *Ensure to check all the wiring harness connected to BCM with Other Modules are proper. *Please disconnect the Battery Negative Cable for 15 minutes and then reconnect. *Clear the codes and check to see if any active DTC's return for U0140 n *If still DTCs U0140 presents then contact Engineering Expert:FCA Redacted Content

Before ordering a new sensor, make sure to disconnect and connect sensor and drive vehicle for 5 minutes above 15 mph. Make sure there is no water into the sensor or harness connector. Please contact engineer FCA Redacted Content before replacing sensor. If no response in 15 minutes, proceed with repair.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

Diagnostic Trouble Code (DTC) U0485 - Implausible Data Received Set. ? Radio reset (Rearview camera functions normally). ? Voice Recognition (VR) inoperable. ? Wireless CarPlayTT inoperable. ? Audio sources inoperable. ? Display switches to Nav on VR prompt. ? Vehicle Positioning (Lat/Long) inoperable. ? Surround View Camera inoperable (Rearview camera functions normally). ? Unable to exit FamCam. ? Audio Repetition inoperable. ? Electric vehicle pages inoperable. ? Translated text is incorrect. ? Profile avatar changes in Valet Mode. ? Display does not return to idle mode after call. ? Dynamic rear view camera guidelines inoperable (Rearview camera functions normally). ? FOTA popup won?t dismiss. ? Ambient Lights Setting inoperable. ? Call Status on after all ended Favorites available in valet mode. ? SXMTT Favorites inoperable. ? Tutorial App inoperable. ? Audio Repetition stops during incoming calls. ? Unable to connect second device. ? Unable to exit Seat Comfort popup. ? Call does not end on the Instrument Panel Cluster (IPC). ? Seat Comfort graphic incorrect. ? Headphone button for front passenger display inoperable. ? Schedule update inoperable. ? USB media source inoperable on front passenger display. ? SXMTT inoperable. ? Wireless Android AutoT inoperable. ? Media sources duplicated. ? Audio unmuted at door close. ? Radio freeze (Rearview camera functions normally). ? Radio input lagging. ? Navigation active with no active route. ? Scheduled cabin cooling inoperable. ? Incorrect phone repetition displayed ? Navigation routing inoperable. ? Unable to exit Electric Vehicle Pages. ? Comfort softkeys incorrect. ? Comfort graphic overlap. ? Unable to change audio sources. ? Audio sources unavailable after profile switch. ? No incoming call popup on Uconnect

Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.

Misfire or rough running.

presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).

noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).

There may be Diagnostic Trouble Codes (DTC)s present. This bulletin involves inspecting and if needed, replacing the intake HLAs.

Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present.

INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head. The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. CAUSE: INTAKE Hydraulic Lash Adjuster may have a manufacturing issue that can cause the plunger to stick, generating valvetrain noise.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Do not diagnose stored or active DTC unless there is a customer facing issue noted. A SOL will be released to give further information.

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Tire Pressure Sensors Values Are Not Displayed

Order a Z part number for all Exchange Orders: Warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only.

to vehicles equipped with: 3 Zone Auto Control-Front/Rear A/C (Sales Code HAH). Air Conditioning w/3 Zone Temp Cntrl (Sales Code HAK). All Vehicles W/Air Conditioning (Sales Code HA0). Rear Air Conditioning w/Heater (Sales Code HBB). This bulletin involves updating the HVAC with the latest available software.

Tech Tip: Reset the IPC module first before any steps are taken to replace the module are undertaken. Connect Witech to the vehicle. Reset all DTCs and check for active DTCs warnings set against IPC. If battery low indicated against IPC, reset the module via WiTech tool. NOTE: After Battery Drainage, the IPC may not function correctly. Please follow the following steps before considering an IPC replacement: 1) Charge the Battery Ensure the battery is fully charged. 2) Soft Reset Perform a soft reset on the IPC. 3) Power-Up Issue 4) If the IPC does not power up, proceed with the following steps: a. Disconnect the battery. b. Reconnect the battery. 5) If condition still exists, consider IPC replacement."

Order a Z part number for all Exchange Orders: Warranty, Mopar, customer pay and service contract. Order regular part number for New, Unsold units only. Please review the latest version of SOL S2208000030 regarding DVD/blue ray issues. After updating software perform resets on both display or concern may still appear. After Battery Drainage VRM do not work. Please follow the following steps. 1. Check VRM proxi, if the VRM is not aligned, perform proxi alignment, reset module. 2. If proxi is correct, reset module 3. Check for DTCs, and check wiring and components related to those DTCs and clear them."

Displayed on Cluster

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Chime"

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): U0140-00 - Lost Communication With Body Control Module. Customers may comment on one or more of the following: Left power sliding door inoperable. Right power sliding door inoperable. This bulletin involves updating the PDSM with the latest available software."

Radio freeze after reverse event (Rearview Camera (RVC) functions normally). Blank hybrid screen. Screen off at start up (RVC functions normally). Radio restart before sleep after switching between different USBs. Pop up error ""setting not saved"" occurring when attempting to enable Geolocation (Privacy Mode Off). Amplifier module sets Diagnostic Trouble Code (DTC) U0485 - Implausible Data Received From Radio. During FOTA scheduling, if OK is not pressed to confirm time selected, vehicle will sleep. Apps downloaded for one connected profile are being shared with other local profiles. Switching profiles with slow response. Slow response switching between camera views. Black radio screen (RVC functions normally). Rear seat reminder alert unavailable. Wi-Fi software update pop-up is being triggered in non-connected vehicles. Switching to Android menu, display screen blinks on green color. Microphone inoperative during SOS call from the vehicle. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from **T25.50 or T27.39** to U29.28. NOTE: The national launch for the FOTA is expected to begin **July 29, 2024.**"

sure all the switches' and airbag's harness are properly connected, disconnect the switches and reconnect them, and reverify the issue. 2.- Pull the SCCM fuse for 60 sec and then reinstall it. 3.- Reverify if Steering wheel switches are inoperative. If there are no DTC's, physical defects, nor switches inop, then SCCM does not need to be replaced.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

VRM not turning on during ignition cycle. This bulletin involves updating the VRM with the latest available software."

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

for any service/replacement of the battery isolator, prior to installation the isolator part must be modified according to the B0A remedy instructions. Please share this with the servicing technician.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

After updating software perform resets on both display or concern may still appear.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

correct image on cluster (should read ?STOP/FINISH? after Parallel and Perpendicular Park Assist maneuver is complete). ? When using perpendicular parking feature, message ?move backwards? stayed on the screen even after the maneuver should have been complete. ? Radio settings won?t save (when saving sound+display together, they will not save unless you have the proper key (teen key). This bulletin involves reprogramming the PAM with the latest software available.

1) . ? Uconnect box backup ?battery low? message on the radio. ? WiFi hotspot streaming lost. ? Rear mirror LED blinking after ignition cycle. ? Uconnect App charge schedule / climate schedule setup issue. ? Customer not seeing profile or other vehicle information on the mobile app. This bulletin involves updating the TBM software from 4.29d to 4.36.

Redacted Content for further assistance. If no response in 15 minutes, proceed with repair.

U11E9 Lost Communication With AGS. Ambient Air Temp Incorrectly Displayed. P0070 And P0073 Set For Ambient Air Temp Sensor

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

After updating software perform resets on both display or concern may still appear.

or B1570-93

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

the following: - Navigation non-functional, not updating current position. - Screen Off hard key inoperative, Soft key on radio screen still operational. - CarPlay and Android Auto stability issues. - Text cut-off in different menus or pop-up messages - Voice Recognition not working for specific voice commands

Order a Z part number for all Exchange Orders: warranty, Mopar, customer pay and service contract. Order regular part number for New unsold units only."

Follow the Infotainment Ordering guide available under the "Parts" section of Dealer Connect: DealerCONNECT> Parts> News& Information> Audio & Electronic Products Exchange Process

the following: Unable to select the Turn by Turn Navigation. Blank Performance Pages (Rearview Camera (RVC) Functions Normally). **Android Auto Voice Recognition (VR) inoperative.** Media Tuner delayed. **Charge Schedule not accepting updates via phone (RVC Functions Normally).** Ambient light inoperative. **Instrument Panel Cluster (IPC) map inoperative.** Media widget blank. Navigation map black. Off road pages inoperative (RVC Functions Normally). VR inoperative. Incorrect song title displayed **(Apple CarPlay only)**. **Radio display switches from the Media page to the Home page (RVC Functions Normally).** Ghost touch on Navigation screen (RVC Functions Normally). Widgets are missing. New User Profile does not load. Display returns to the wrong page after the View ""Camera Event"" button is selected by customer in the ""Camera View Pages"" (RVC Functions Normally). This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from U29.28 or U33.9 to U33.43. NOTE: The Estimated National launch date is August 31, 2024."

the following: Unable to select the Turn by Turn Navigation. Blank Performance Pages (Rearview Camera (RVC) Functions Normally). Android Auto Voice Recognition inoperative. Media Tuner delayed. Charge Schedule HMI (RVC Functions Normally). Ambient Light inoperative. Map in Cluster inoperative. Media Widget blank. Navigation Map black. Off road pages inoperative (RVC Functions Normally). VR inoperative. Incorrect song title displayed (Carplay only). HU switches from Media Page to Home Page (RVC Functions Normally). Ghost Touch on Navigation screen (RVC Functions Normally). Widgets missing. New user profile does not load. Returns to wrong page after View Camera Event selected by customer in the ""Camera View Pages"" (RVC Functions Normally). This bulletin provides information regarding the latest FOTA update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from U29.28 or U33.9 to U33.43. NOTE: The Estimated National launch date is August 31, 2024."

inoperative.** ? Right and/or Left rear seat entertainment screen(s) goes blank. This bulletin involves checking and if needed, updating the software on both rear seat entertainment display screens.

U11E9 Lost Communication With AGS. Ambient Air Temp Incorrectly Displayed. P0070 And P0073 Set for Ambient Air Temp Senso

display (this is a radio to display signal issue, not a rearview camera to display signal issue), prior to replacing this part, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

chatter/streak/jump/skip/smear or make noise while traveling across the windshield.

It has been determined that the issue is with the trim carpet the headrest strap goes through, not the headrest mechanism. Please do not replace the headrest/headrest mechanism and instead refer to SOL S2423000025 for the proper rework procedure that should be done"

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

is stuck."

It has been determined that the issue is with the trim carpet the headrest strap goes through, not the headrest mechanism. Please do not replace the headrest/headrest mechanism and instead refer to SOL S2423000025 for the proper rework procedure that should be done"

Please do not try to open the Switch nor fix it. Just return the part and order a new one.

Please verify proper functionality of both sliding doors (power or manual) switch the door into manual mode. Then, put the door in secondary and see if it will cinch and release through all inputs (overhead console, key fob, handle grab) 2. If sliding doors operate as expected, do NOT replace sliding door latch(es) 3. If possible, please provide any / all information in the repair order narrative regarding status of sliding door function (i.e, door only works manually, won't open via key fob, etc.). This includes all customer feedback as well (what exactly brought the customer into the dealer).

Please do not try to open the Switch nor fix it. Just return the part and order a new one.

Please verify proper functionality of both sliding doors (power or manual) switch the door into manual mode. Then, put the door in secondary and see if it will cinch and release through all inputs (overhead console, key fob, handle grab) 2. If sliding doors operate as expected, do NOT replace sliding door latch(es) 3. If possible, please provide any / all information in the repair order narrative regarding status of sliding door function (i.e, door only works manually, won't open via key fob, etc.). This includes all customer feedback as well (what exactly brought the customer into the dealer).

Country/ 2013 - 2020 Dodge Caravan (RT) - Corrosion - Complete Hood Panel Warranty Claim Simplification (Rev. B)

2020 Dodge Caravan (RT) - Corrosion - Complete Hood Panel Warranty Claim Simplification (Rev. B)

This bulletin includes Inspecting and if necessary getting the window shade tab unstuck from the interior panel.

Country/ 2013-2020 Dodge Caravan (RT) - Corrosion Complete Hood Panel Warranty Claim Simplification (Rev. A)

Dodge Caravan (RT) - Corrosion Complete Hood Panel Warranty Claim Simplification (Rev. A)

If no response in 15 minutes, proceed with repair.

this is normal and not a defect.

If no response in 15 minutes, proceed with repair.

If no response within 15 minutes, proceed with the repair.

C0604- Active Air Dam Control Performance

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

TPM Lamp On.

TPM Lamp On.

ON'"

not Detected message, Tire Pressure Warning Lamp On

Red Wrench Light On, Electric Drive Modes Disabled

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

PRIOR TO PERFORMING ANY THERMOSTAT REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2309000014

Library for specifications so a suitable alternative can be used

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

"

coming from the front end of the vehicle when driving over bumps. This bulletin involves inspecting and possibly replacing one or both front upper isolator springs."

Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.

B)

steering wheel control to cycle through the presets, skips through several of the preset channels and calls other SXM stations not on the preset list. After an overnight sleep cycle, preset bar stays blank in the Media tab and media widget. Whenever the "Navigation Turn-by-Turn Displayed in Cluster" button is checked, once a different tab is selected, the previously checked box becomes unchecked This bulletin involves updating the software to U33.43.

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

DTSs U11E3, U0103, U1267 For Loss Of Communication With The Electronic Gear Shift Module

In repair procedure the dealerships are replacing the CAN star block connector during their root cause process with returned parts showing no trouble found. Here is a list of steps the dealers can follow to determine if they have a defective CAN star block connector using a multimeter: Step 1: Visually review CAN star block for damage and ensure back cover has all locking tabs engaged. If a bent pin, cracked or damaged housing or locking tab is not engaged is observed then replacement is required. Step 2: Identify Connector #1 as the 3 Pin Connector cavity Step 3: Measure resistance between Pin#1 and Pin#2 in Connector #1. Acceptable values are 120.4 Ohms to 139.8 Ohms. If resistance is outside of this range then replacement is required. Step 4: Measure the continuity between Pin#1 in Connector #1 to Pin#1 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required. Step 5: Measure the continuity between Pin#2 in Connector #1 to Pin#2 in each of the other 2 Pin connector cavities. If continuity is not found then a replacement is required.

Due to brake vacuum pumps returned with trouble not found, please follow the proper diagnostics outline in the service library this also includes checking all electrical and vacuum hose connections prior to replacement of the vacuum pump. This will avoid unnecessary repair and potential charge back on the vacuum pump.

updated diagnostic procedures in the service library which may indicate the smart actuator replacement (PN 68369691AD) is the proper repair.