2027 Chrysler Pacifica TSBs

The power sliding door will not open with the button. Latch popping noise heard when attempting to opening and/or closing the power sliding door. NOTE: Doors will open manually This bulletin involves inspecting and possibly reprogramming the PDSMs with the latest available software.

screen or a blank center screen when using the submenus. This black screen may occur when preparing the RU for pre-delivery. Please do not replace the radio. The solution is to reset the radio and retry the submenus to assure that the issue is resolved. If the issue resolution is not in place, it is recommended that a hard reset be done for the ETMR1H. The hard reset can be done by disconnection of the radio completely and reconnecting. Another way is to completely disconnect the positive battery terminal such that the radio is completely without power and reconnecting. Once again, please do not remove and replace the radio with the failure mode of a black or blank screen. Current SW U42.13 is the production level SW for the ETMR1H and will be updated in the next few months."

gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.

gauge accuracy and drivability issues, the technician should disconnect the electrical connector at the pump and perform a visual inspection of the connector for and bent, spread, or pushed out terminals. Repair any issues found. Reconnect the plug and perform a push pull push to ensure the connector is fully installed. Then perform 3 keys cycles and listen to hear if the fuel pump is operational. If the fuel pump is heard that indicates that everything is operating correctly. If the pump is heard replacement is not necessary, any replacement will function in the same way.

A/C relay clutch not operating, dealers are unnecessary replacing PDCs. Battery disconnection is required to reset PCM. Please follow SOL S2624000004.

C1477-48 may also be present. To engage AWD, the DTCM energizes the hydraulic pump inside the RDM to apply the torque transfer clutch. This allows the propeller shaft to spin up to speed and match the front axle speed allowing the shift fork in the PTU to engage without clashing. The DTCM utilizes the pressure sensor on the RDM to determine the amount of hydraulic pressure applied to the clutches. If that pressure sensor fails, there can be inadequate pressure, preventing the driveshaft from coming up to speed when going into AWD. This will cause a grinding noise in the PTU. If the vehicle comes in with a grinding noise coming from the PTU, prior to replacing the PTU or RDM, replace the RDM pressure sensor 68227790AD and verify whether the concern has been resolved.

Multiple Warning Indicators On In The IPC. ESM - PRNDL Flashing. And The Vehicle Will Not Shift Into Gear. The Wipers May Be On, With An Electric Parking Brake Unavailable.

Check the Strut bearings, Strut mounts, or similar suspension components prior to replacing Steering Gears. Previous customers have returned after EPS gear was replaced. Strut bearings are the most frequent cause of RU BSR complaints.

Navigation Stability - Android Auto & Carplay s ustomers may experience one or more of the following:- Navigation Stability - Android Auto & Carplay stability & connectivity- Distorted/glitchy display prior to startup animation- Text appearance display- Widget incorrect display- Turn signal blind spot response timing- Audio cut out - Drive Modes selection- Park assist Guidelines selctiontability & connectivity- Distorted/glitchy display prior to startup animation- Text ap

load on the Home/Split screen Fig. 1.

Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay

Cluster (IPC) when the turn-by-turn feature is enabled. This issue occurs when using Google Maps for Navigation via CarPlay

replacing RU Blower motor, with PN#68308952AD

vehicle must SYMPTOM: exhibit/set the following Diagnostic Trouble Code (DTC): P072F-00 - Stuck In Gear 4. Customers may also comment on the following: During normal vehicle operation, while decelerating from 7th gear, the MIL illuminates and the vehicle enters a limp-in (reduced power) mode. This bulletin involves performing the transmission "QuickLearn" procedure using wiTECH.

part, we want to notify them to review Star Online S2208000045 before replacing cameras for poor image quality (fuzzy, blurry, pixelated) to ensure camera replacement is warranted / justified. This SOL provides a process for evaluating if the camera's image quality is within a typical range.