2019 Chrysler Pacifica TSBs

Not be able to use Mobile Wi-Fi upon start up. Hotspot gives a no Internet connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from JR34.3 to JR34.32. NOTE: National launch for this FOTA update is expected to begin February 20, 2023.

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay connectivity improvement. Improvement to Bluetooth phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.

IPhone Is Connected

Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from IR22.64 and IR22.65 to IR22.66. The national launch for the FOTA is expected to begin on January 09, 2023. ? Wi-Fi hotspot connection not working. ? No internet connection message on the phone when trying to connect to a device

IPhone Is Connected

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay connectivity improvement. Improvement to Bluetooth phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.

IPhone Is Connected

2) For concern of a "Yellow Band" on the center stack display, swapping the radio or display will NOT resolve the issue. The issue was corrected in a recently released software update. Please visit Service Library for the latest in diagnostic information. For any questions, please contact: Anmol Shergill (248) 512-1207 - Anmol.Shergill@external.fcagroup.com or Ashikur Rahman (248) 512- 6715 - Ashikur.Rahman@external.fcagroup.com

published document)

published document)

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. This is part of a two step FOTA update, first update brings software level to 22.61 and this second FOTA update will take the software to 22.64. National launch for this second step is May 24, 2021. Customers may experience one or more of the following:Navigation is incorrect or can not calculate route. GPS locations is inaccurate. Uconnect radio apps are all inoperable. Backup camera screen is blue (DT and KL). Green horizontal lines appear across screen (DT and KL). Anti-theft code request message. Backup camera screen is blank. Lines appear across screen. Radio control screen is blank or locked. Radio reset intermittently. Unable to adjust audio volume. Unable to switch modes between AM, FM, SAT or Media. In addition the following enhancements are included in this update:Carplay connectivity improvement. Improvement to Bluetooth phone pairing. Bluetooth devices unresponsive. Improved sound quality when using a Bluetooth phone.

IPhone Is Connected

2) For concern of a "Yellow Band" on the center stack display, swapping the radio or display will NOT resolve the issue. The issue was corrected in a recently released software update. Please visit Service Library for the latest in diagnostic information. For any questions, please contact: Anmol Shergill (248) 512-1207 - Anmol.Shergill@external.fcagroup.com or Ashikur Rahman (248) 512- 6715 - Ashikur.Rahman@external.fcagroup.com

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

08-ELECTRICAL/8N-POWER SYSTEMS/DIAGNOSIS AND TESTING/POWER LIFTGATE CHIME For concern of liftgate chime inoperative, please contact FCA Redacted Content. If no answer, please leave your name and a callback number. If no response in 15 minutes, proceed with repair.

Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp

Tire Pressure Sensors Values Are Not Displayed

Tire Pressure Sensors Values Are Not Displayed

Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp

Customers may experience one or more of the following: One or both of the rear screens are not working after rear display replacement.If the rear display is replaced and it does not function, confirm that the Video Routing Module (VRM) software is up to date. Black screen on both rear screens(2017-19 MY Only). Rear Seat Entertainment (RSE) remote control does not pair. When playing a video from a USB stick the video does not resume where itleft off after an ignition cycle(2017-19 MY Only). Video Screens do not turn on(2017-18 MY Only). Radio Uconnect theater button does not work(2017-18 MY Only). USB playback is choppy (2017 MY Only). The video system resets or does not function(2017 MY Only). The remote pairing screen will time out and inform customer the remote(s)have not been paired(2017 MY Only). Remotes frequently do not pair(2017 MY Only). Occasional reset(2017 MY Only). Rear screens can be accidently controlled from the radio outside of theparental control feature(2017 MY Only). Black screen(2017 MY Only). Upon further investigation the technician may find that the following Diagnostic Trouble Code(DTC) has been set(2017-19 MY Only):B15AD-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 1. B15AE-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 2. B15AA-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display1. B15AB-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display2.Low Voltage Differential Signal (LVDS) DTCs (B15AD00, B15AE00, B15AB00, B15AA00) get falsely set when thevehicle is remote started. U11BB-00 - Lost Communication With Video Routing Module(2017-19 MY Only). In addition the following improvement is included. Blueborn cyber security patch(2017-19 MY Only).

08-ELECTRICAL/8N-POWER SYSTEMS/DIAGNOSIS AND TESTING/POWER LIFTGATE CHIME For concern of liftgate chime inoperative, please contact FCA Redacted Content. If no answer, please leave your name and a callback number. If no response in 15 minutes, proceed with repair.

Customers may experience one or more of the following: Lost radio presets. High pitch squeal, pop or humming sound coming from all of the speakers. SXM favorite song list empty. Radio display screen is black when the ignition is on. Radio may reset/reboots, turn itself off and then back on again. Radios resets when a Bluetooth paired phone receives two text messages one after another simultaneously after approximately seven seconds. (ABD sales code). Incorrect navigation address/location/directions. Navigation stuck on loading screen or not appearing at all. Lost navigation settings. Speaker crackling noise on non amplified vehicles (UAV Only). Active call not transferred to vehicle Bluetooth (UAV Only). Voice Recognition (VR) not understanding commands to switch sources (UAV Only). Bluetooth phonebook not available (UAV Only). "Setting" button removed after ignition cycle (UAV Only). Coolant temperature value incorrect (UAV Only). Speaker crackling noise. In addition the following enhancements are included:Bluetooth improvements. VR improvements. Improve Navigation zoom and scrolling feature on map.

Customers may experience one or more of the following: Black screen on Video Routing Module (VRM)/Rear Seat Entertainment (RSE) displays. One or both of the rear screens are not working after rear display replacement.If the rear display is replaced and it does not function, confirm that the VRM software is up to date. RSE remote control does not pair. When playing a video from a USB stick the video does not resume where it left off after an ignition cycle(2017-19 MY Only). Video Screens do not turn on(2017-18 MY Only). Radio Uconnect theater button does not work(2017-18 MY Only). USB playback is choppy(2017 MY Only). The video system resets or does not function(2017 MY Only). The remote pairing screen will time out and inform customer the remote(s) have not been paired(2017 MY Only). Remotes frequently do not pair(2017 MY Only). Occasional reset(2017 MY Only). Rear screens can be accidently controlled from the radio outside of the parental control feature(2017 MY Only). Black screen(2017 MY Only). Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Code (DTCs) have been set:U11BB-00 - Lost Communication With Video Routing Module. B15AD-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Media Port 1. B15AE-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Media Port 2. B15AA-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display 1. B15AB-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display 2.Low Voltage Differential Signal (LVDS) DTCs (B15AD00, B15AE00, B15AB00 and B15AA00) get falsely set when the vehicle is remote started. In addition the following improvement is included:Blueborn cyber security patch(2017-19 MY Only).

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may notice one or more of the following DTCs have been set: P0AA1-00 - Hybrid/EV Battery Positive Contactor ?A? Stuck Closed. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. P0B3C-00 - Hybrid/EV Battery Voltage Sense 1 Circuit Performance. P0B41-00 - Hybrid/EV Battery Voltage Sense 2 Circuit Performance. P0B46-00 - Hybrid/EV Battery Voltage Sense 3 Circuit Performance. P0B4B-00 - Hybrid/EV Battery Voltage Sense 4 Circuit Performance. P0B50-00 - Hybrid/EV Battery Voltage Sense 5 Circuit Performance. P0B55-00 - Hybrid/EV Battery Voltage Sense 6 Circuit Performance. P1A16-00 - Hybrid/EV Wakeup Control 3 Output Circuit/Open. P1D7B-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Battery. P1D7C-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Ground. P1A29-00 - Cell Supervisory Circuit A Failure. P1A2A-00 - Cell Supervisory Circuit B Failure. Customer may also experience one or more of the following:Premature oil change message displayed on the cluster and vehicle may be running in fuel/oil refresh mode. Scheduled charging not functioning properly because the battery pack did not wake up while plugged in.

Customers may experience one or more of the following: One or both of the rear screens are not working after rear display replacement.If the rear display is replaced and it does not function, confirm that the Video Routing Module (VRM) software is up to date. Black screen on both rear screens(2017-19 MY Only). Rear Seat Entertainment (RSE) remote control does not pair. When playing a video from a USB stick the video does not resume where itleft off after an ignition cycle(2017-19 MY Only). Video Screens do not turn on(2017-18 MY Only). Radio Uconnect theater button does not work(2017-18 MY Only). USB playback is choppy (2017 MY Only). The video system resets or does not function(2017 MY Only). The remote pairing screen will time out and inform customer the remote(s)have not been paired(2017 MY Only). Remotes frequently do not pair(2017 MY Only). Occasional reset(2017 MY Only). Rear screens can be accidently controlled from the radio outside of theparental control feature(2017 MY Only). Black screen(2017 MY Only). Upon further investigation the technician may find that the following Diagnostic Trouble Code(DTC) has been set:U11BB-00 - Lost Communication With Video Routing Module. B15AD-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 1. B15AE-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 2. B15AA-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display1. B15AB-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display2.Low Voltage Differential Signal (LVDS) DTCs (B15AD00, B15AE00, B15AB00, B15AA00) get falsely set when thevehicle is remote started. In addition the following improvement is included. Blueborn cyber security patch(2017-19 MY Only).

Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Ghost Touch, features, modes and App?s changing without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first start the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Audio distortion (KL vehicles). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay or Android Auto Google maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. Personal Identification Number (PIN) clears and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. Intermittently requires an anti-theft code to be entered. Software update also includes software enhancement.SXM sound and behavior improvements.

Improper handling of damaged lithium ion batteries can cause property damage, serious injury or even death. Exemptions will not be made for any dealer who fails to follow the appropriate handling process.To read the DCMail communication, go to DealerCONNECT > DCMail (ID: 81758) For details on recyclers, please visit the Mopar Dealer Site Lithium Ion Battery Handling page: https://www.dealers-mopar.com/moparone/retail/programs/battery-program/lithium-ion.jsp

must be followed for BEV/Hybrid vehicles that are on display at dealership showrooms.

Customers may experience one or more of the following: One or both of the rear screens are not working after rear display replacement.If the rear display is replaced and it does not function, confirm that the Video Routing Module (VRM) software is up to date. Black screen on both rear screens(2017-19 MY Only). Rear Seat Entertainment (RSE) remote control does not pair. When playing a video from a USB stick the video does not resume where itleft off after an ignition cycle(2017-19 MY Only). Video Screens do not turn on(2017-18 MY Only). Radio Uconnect theater button does not work(2017-18 MY Only). USB playback is choppy (2017 MY Only). The video system resets or does not function(2017 MY Only). The remote pairing screen will time out and inform customer the remote(s)have not been paired(2017 MY Only). Remotes frequently do not pair(2017 MY Only). Occasional reset(2017 MY Only). Rear screens can be accidently controlled from the radio outside of theparental control feature(2017 MY Only). Black screen(2017 MY Only). Upon further investigation the technician may find that the following Diagnostic Trouble Code(DTC) has been set:U11BB-00 - Lost Communication With Video Routing Module. B15AD-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 1. B15AE-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 2. B15AA-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display1. B15AB-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display2.Low Voltage Differential Signal (LVDS) DTCs (B15AD00, B15AE00, B15AB00, B15AA00) get falsely set when thevehicle is remote started. In addition the following improvement is included. Blueborn cyber security patch(2017-19 MY Only).

Customers may experience one or more of the following:Radio display screen flickers. Clock loses 6 seconds per day (JL with 5 inch screen). Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Ghost Touch, features, modes and App?s changing without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first start the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Audio distortion (KL vehicles). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay or Android Auto Google maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. Personal Identification Number (PIN) clears and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. Intermittently requires an anti-theft code to be entered. Software update also includes software enhancement.SXM sound and behavior improvements.

Customers may experience one or more of the following: One or both of the rear screens are not working after rear display replacement.If the rear display is replaced and it does not function, confirm that the Video Routing Module (VRM) software is up to date. Black screen on both rear screens(2017-19 MY Only). Rear Seat Entertainment (RSE) remote control does not pair. When playing a video from a USB stick the video does not resume where itleft off after an ignition cycle(2017-19 MY Only). Video Screens do not turn on(2017-18 MY Only). Radio Uconnect theater button does not work(2017-18 MY Only). USB playback is choppy (2017 MY Only). The video system resets or does not function(2017 MY Only). The remote pairing screen will time out and inform customer the remote(s)have not been paired(2017 MY Only). Remotes frequently do not pair(2017 MY Only). Occasional reset(2017 MY Only). Rear screens can be accidently controlled from the radio outside of theparental control feature(2017 MY Only). Black screen(2017 MY Only). Upon further investigation the technician may find that the following Diagnostic Trouble Code(DTC) has been set(2017-19 MY Only):B15AD-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 1. B15AE-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 2. B15AA-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display1. B15AB-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display2.Low Voltage Differential Signal (LVDS) DTCs (B15AD00, B15AE00, B15AB00, B15AA00) get falsely set when thevehicle is remote started. U11BB-00 - Lost Communication With Video Routing Module(2017-19 MY Only). In addition the following improvement is included. Blueborn cyber security patch(2017-19 MY Only).

08-ELECTRICAL/8N-POWER SYSTEMS/DIAGNOSIS AND TESTING/POWER LIFTGATE CHIME For concern of liftgate chime inoperative, please contact FCA Redacted Content. If no answer, please leave your name and a callback number. If no response in 15 minutes, proceed with repair.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may notice one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P1A29-00 - Cell Supervisory Circuit A Failure. P1A2A-00 - Cell Supervisory Circuit B Failure.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

DTC C1252-92 VACUUM PUMP CONTROL CIRCUIT And Or P258B ELECTRONIC VACUUM PUMP PERFORMANCE

Customers may experience the following:Black screen on both rear screens. Rear Seat Entertainment (RSE) remote control does not pair. When playing a video from a USB stick the video does not resume where itleft off after an ignition cycle. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) has beenset:B15AD-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 1. B15AE-00 - Lost Low Voltage Differential Signal (LVDS) Connection With MediaPort 2. B15AA-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display1. B15AB-00 - Lost Low Voltage Differential Signal (LVDS) Connection With Display2.Low Voltage Differential Signal (LVDS) DTCs (B15AD00, B15AE00, B15AB00, B15AA00) get falsely set when thevehicle is remote started. U11BB-00 - Lost Communication With Video Routing Module. In addition the following improvement is included.Blueborn cyber security patch.

Customers may experience one or more of the following: Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Ghost Touch, features, modes and App?s changing without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first start the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Audio distortion (KL vehicles). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay or Android Auto Google maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. Personal Identification Number (PIN) clears and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. Intermittently requires an anti-theft code to be entered. Software update also includes software enhancement. SXM sound and behavior improvements.

Customers may experience one or more of the following:Green horizontal lines on back up display, in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Ghost Touch, features, modes and App?s changing without drivers input. Speaker pop noise when using Bluetooth device. When vehicle is first start the radio will reset and the time display shows 12:00. Audio distortion and volume fluctuation. Blank rear camera image in reverse (If this is the customer concern use camera LOP 18-60-02-W2, on DT and JL vehicles only). Audio distortion (KL vehicles). Audio cutting in and out during memory recall. Ring tone too loud. AM/FM volume fluctuates. While in CarPlay or Android Auto Google maps showing wrong location. Phone disconnected after first call. Black screen or White screen with vertical lines. Personal Identification Number (PIN) clears and volume locked while KeySense is used. Audio static while in SXM/SAT modes. Echo heard during Bluetooth phone calls. The radio is locked up. The radio remains on after ignition has been turned off. The radio resets. The radio screen turns black. Intermittently requires an anti-theft code to be entered. Software update also includes software enhancement.SXM sound and behavior improvements.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

Please do not try to open the Switch nor fix it. Just return the part and order a new one.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Please do not try to open the Switch nor fix it. Just return the part and order a new one.

Country/ 2013 - 2020 Dodge Caravan (RT) - Corrosion - Complete Hood Panel Warranty Claim Simplification (Rev. B)

2020 Dodge Caravan (RT) - Corrosion - Complete Hood Panel Warranty Claim Simplification (Rev. B)

Country/ 2013-2020 Dodge Caravan (RT) - Corrosion Complete Hood Panel Warranty Claim Simplification (Rev. A)

Dodge Caravan (RT) - Corrosion Complete Hood Panel Warranty Claim Simplification (Rev. A)

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Mirror Contacts Door Window Glass In The Folded Position.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

Dodge Caravan (RT) - Corrosion ? Complete Hood Panel Warranty Claim

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

please refer to the following steps: 1. Please verify proper functionality of both sliding doors (power or manual) through all inputs (overhead console, key fob, handle grab). 2. If sliding doors operate as expected, do NOT replace sliding door latch(es). 3. If service is required, and your Dealership is located in the Detroit Metro Area please contact FCA Redacted Content, prior to replacing any sliding door latch(es). If no response in 15 minutes, proceed with repair. 4. If possible, please provide any / all information in the repair order narrative regarding status of sliding door function (i.e, door only works manually, won't open via key fob, etc.). This includes all customer feedback as well (what exactly brought the customer into the dealer).

industry awareness regarding the recommended usage of Authentic Mopar Glass.

one of the following Christine Lepain at (226) 280-3035 or Frank Merino at (248) 760-3557 If no response in 15 minutes, proceed with repair.

If no response in 15 minutes, proceed with repair.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

answer, please leave your name and a callback number. If no response in 15 minutes, proceed with repair.

center hinge If customer comes in with the issue described above, please contact the following individuals prior to servicing the vehicle. FCA Redacted Content and/or FCA Redacted Content If no response in 15 minutes, proceed with repair.

center hinge If customer comes in with the issue described above, please contact the following individuals prior to servicing the vehicle. FCA Redacted Content and/or FCA Redacted Content If no response in 15 minutes, proceed with repair.

center hinge If customer comes in with the issue described above, please contact the following individuals prior to servicing the vehicle. FCA Redacted Content and/or FCA Redacted Content If no response in 15 minutes, proceed with repair.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

one of the following Christine Lepain at (226) 280-3035 or Frank Merino at (248) 760-3557 If no response in 15 minutes, proceed with repair.

or laieth-james.khoury@fcagroup.com If no response in 15 minutes, proceed with repair.

latch from the rear window breaking. Carefully inspect the part for small shards of glass.

There may also be associated driveability issues. Upon further investigation, the following fault codes may be found in the PCM:

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

Powertrain Mounting Neutralization Procedure. Discussion: Service information is in the process of being updated to include powertrain mount installation best practices. The new procedure will neutralize the mounts to lessen or remove unwanted mount tension that can lead to vibration complaints.

Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. Customers may comment on one or more of the following: Rough idle. Valvetrain noise. "

Refer to SOL # S2509000004. It is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets). Once it is confirmed that the repair will be done using the camshaft/Rocker arms kit, it is also important to confirm that the vehicle being repaired has the latest calibration/software update for oil pump operation mode (high pressure mode) during engine start up. RU, VF, WL & WD vehicles already include the latest oil pump mode in all 25MY and beyond. 24MY service releases are also available. JL & JT were updated as a running change in 24MY and beyond (08/15/24 & 08/19/24 respectively). 24MY service releases available. DT was updated starting 25MY and beyond. If the vehicle to be repaired is a 24MY vehicle with a service release available, please follow the released service procedures to update to the corresponding calibration/software update.

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

*Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0A3F - Drive Motor A Position Sensor 1 Circuit. P0A43 - Drive Motor A Position Sensor Circuit Intermittent. P0A45 - Drive Motor B Position Sensor 1 Circuit. P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: Hybrid Control Processor (HCP). Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM "

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures."

Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

Brake Pedal Position Sensor Circuit Performance, P1572 Brake Pedal Stuck, C0042-54 Brake Pedal Missing Calibration

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

PRIOR TO PERFORMING ANY WATER PUMP REPLACEMENT, PROCEED WITH INSPECTION INSTRUCTIONS FROM THE LATEST VERSION OF STAR ONLINE PUBLICATION S2307000002. Please submit pictures of the leak area thru the DIDI process outlined in the STAR Online document. NOTE: Some coolant residue may be found at the water pump weep hole plug area which may be normal, but coolant should not be dripping from this location. If unsure about, use the Pressurized Coolant System Inspection process as found in the Dealer Connect Cooling Diagnosis and Testing Procedures.

Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.

Misfire or rough running.

presence, only AB or previous LEVEL PSU right intake camshaft PN 05047913AA or AB (old version) should be replaced. If the engine is equipped with the AC/AD LEVEL PSU right intake camshaft PN 05047913AC or AD (new version), camshaft should NOT be replaced. Case 2) If the intake camshaft or intake rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).

noise, please check that the INTAKE Hydraulic Lash Adjusters are not "collapsed". If a collapsed INTAKE HLA is found, replace all INTAKE HLAs on the suspect cylinder head (no need to replace rocker arms). The noise can occur at low or high RPMs, and at low or high temperatures. There are no Diagnostic Trouble Codes (DTC)s present. Case 2.- If the INTAKE camshaft or INTAKE rocker arm has excessive wear on the high lift profile (Rocker arm: slider, Camshaft: central lobe), replace the intake camshaft (1) in that cylinder head and all intake rocker arms (6).

Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0A3F - Drive Motor A Position Sensor 1 Circuit. ? P0A43 - Drive Motor A Position Sensor Circuit Intermittent. ? P0A45 - Drive Motor B Position Sensor 1 Circuit. ? P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: ? Vehicle is in limp mode. Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: ? Hybrid Control Processor (HCP). ? Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission.

Brake Pedal Position Sensor Circuit Performance, P1572 Brake Pedal Stuck, C0042-54 Brake Pedal Missing Calibration

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.

(ETL, ETM, ETN Engines)

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.

reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P2797-00 - Auxiliary Transmission Fluid Pump Performance. P0CF3-00 - Control Pilot Circuit Open. P0A44 - Drive Motor A Position Sensor 1 Circuit Overspeed. U0111-00 - Lost Communication With Battery Energy Control Module (BPCM). P1625-00 - Park Pawl System Failure. U0412-00 - Invalid Data Received From Battery Energy Control Module-A. P215B-00 - Vehicle Speed Output Shaft Speed Correlation. P079A-00 -Transmission Friction Element 1 Slip Detected. P079B-00 - Transmission Friction Element 2 Slip Detected. Customers may also comment:Vehicle will not start when temperature is -30 C (-22 F) and below. Heard and/or felt bump when the gas engine turns on while driving. Vehicle will not charge beyond 98%. "Service Charging System" and "Traction Battery Cutoff" warning messages appear during a key cycle event at -7 C (-20F). Vehicle will force to Park when keyed off in Neutral if the door is open during wake-up procedure and remains open or within 2 minutes of door closure. Loss of PSA when ignition push-button is pressed by driver after a Remote Start. Unusual battery drain when DTC, P084F-00 - Park-Neutral Switch Output is set. This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes.

Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience:Noise or vibration heard/felt during a gas engine start in park. This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this PCM update:Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS). Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM).

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs. P0A2D-00 - Drive Motor ?A? Temperature Sensor ?A? Circuit High. P0A33-00 - Drive Motor B Temperature Sensor 1 Circuit High. Technicians and/or customers may also report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Customers may also experience: Noise or vibration heard/felt during a gas engine start in park. This software release includes the following software enhancement: Corrections to allow the vehicle to clear the permanent fault codes. Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this PCM update:Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS). Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM).

reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1AF8-00 - MCPA Control Module Shutdown Performance. P1AFE-00 - MCPB Improper Shut Down.P1AF8-00&P1AFE-00 will now be set as a 1 trip failure instead of a 2 trip failure. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P0A46-00 - Drive Motor B Position Sensor 1 Circuit Range-Performance. P0A40-00 - Drive Motor A Position Sensor 1 Circuit Range-Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P0CF3-00 - Control Pilot Circuit Open. P0A44 - Drive Motor A Position Sensor 1 Circuit Overspeed. U0111-00 - Lost Communication With Battery Energy Control Module (BPCM). P1625-00 - Park Pawl System Failure. U0412-00 - Invalid Data Received From Battery Energy Control Module-A. P215B-00 - Vehicle Speed Output Shaft Speed Correlation. P079A-00 - Transmission Friction Element 1 Slip Detected. P079B-00 - Transmission Friction Element 2 Slip Detected. Customers may also comment:Vehicle will not start when temperature is -30 C (-22 F) and below. Heard and/or felt bump when the gas engine turns on while driving. Vehicle will not charge beyond 98%. "Service Charging System" and "Traction Battery Cutoff" warning messages appear during a key cycle event at -7 C (+20F). Vehicle will force to Park when keyed off in Neutral if the door is open

(9) flywheel to damper bolts (68382486AA) when replacing the SI-eVT per TechConnect procedure. North America RU vehicles built prior to Nov 28, 2019 had a 05192374AB level cooler. All subsequent Si-eVT versions have the 05192374AC level cooler requires new 68413378AA inlet hose and 68425381AA outlet hose to service Nov 28, 2019 and prior VINs. China RU vehicles built prior to June 11, 2019 had a 05192374AB level cooler. All 68405320AC have the 05192374AC level cooler requires new 68413378AA inlet hose and 68425381AA outlet hose. The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door. Production SI-eVTs have used motor "A" stators with 0.6 mm and 0.8 mm air gap. The PIM software must match the air gap. Mopar will now ship 68490840A* service SI-eVTs with a 0.8 mm air gap ONLY. Dealers are required to provide a VIN to the Star Center so the DNA of the VIN can be set to the 0.8 mm air gap software. In China, read the SI-eVT model number on the transmission ID tag or imprinted on the case. - all 05062509A*, B* have a 0.6 mm gap so use 68405320AC - all 05062509CA and later (0.8 mm gap) use 68490848AA

reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P2797-00 - Auxiliary Transmission Fluid Pump Performance. P0CF3-00 - Control Pilot Circuit Open. P0A44 - Drive Motor A Position Sensor 1 Circuit Overspeed. U0111-00 - Lost Communication With Battery Energy Control Module (BPCM). P1625-00 - Park Pawl System Failure. U0412-00 - Invalid Data Received From Battery Energy Control Module-A. P215B-00 - Vehicle Speed Output Shaft Speed Correlation. P079A-00 -Transmission Friction Element 1 Slip Detected. P079B-00 - Transmission Friction Element 2 Slip Detected. Customers may also comment:Vehicle will not start when temperature is -30 C (-22 F) and below. Heard and/or felt bump when the gas engine turns on while driving. Vehicle will not charge beyond 98%. "Service Charging System" and "Traction Battery Cutoff" warning messages appear during a key cycle event at -7 C (-20F). Vehicle will force to Park when keyed off in Neutral if the door is open during wake-up procedure and remains open or within 2 minutes of door closure. Loss of PSA when ignition push-button is pressed by driver after a Remote Start. Unusual battery drain when DTC, P084F-00 - Park-Neutral Switch Output is set. This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes.

Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience:Noise or vibration heard/felt during a gas engine start in park. This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this PCM update:Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS). Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM).

(ETL, ETM, ETN Engines)

specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.

specifications to possibly eliminate a leak at the case split line of the transmission. Customers may notice (possibly transmission) fluid leaking on the ground from the left front of the vehicle.

be advised that the engine oil capacity is 5 quarts of oil.

Sensor Circuit Performance

verify that there are no steel dowel pins pressed into the cylinder head. If dowels are present in the cylinder head please remove carefully without touching/damaging the cylinder head sealing surface.

None of the seals from the PTU side will need to be replaced whenever the ATX stubshaftis replaced, even though V-seal (68408748A$) is in direct contact with the stubshaft,it will not avoid grease/oil leakage from transmission side. PTU V-seals are intended to act as a dust cover for stubshaft-PTU input shaft spline interface. PTU Input shaft seal (68408749A$) is intended to hold PTU oil and debris ingress; it should be replaced only if the fluid leakage is confirmed to be PTU oil and not ATX trans. fluid.

the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick.

If no response in 15 minutes, proceed with repair.

this is normal and not a defect.

If no response in 15 minutes, proceed with repair.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

semi and full synthetic oils.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

TPM Lamp On.

TPM Lamp On.

Red Wrench Light On, Electric Drive Modes Disabled

industry awareness regarding the use of recycled or salvage parts.

A U11E9, or B16FB-15 may be set

A U11E9, or B16FB-15 may be set

A U11E9, or B16FB-15 may be set

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Lost radio presets. ? SXM favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Lost navigation settings. ? SXM icon inoperative (D-Truck). ? Radio display screen is black when the ignition is on (Rear View Camera (RVC) not affected (D-Truck)). ? Radio freeze intermittent (RVC not affected (D-Truck)). ? Wireless connectivity pair or connection issue (D-Truck). ? Radio channel changes by itself (D-Truck). ? Backup camera has black display screen, or Only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) (D-Truck). ? High pitch chime noise (D-Truck). ? Contact list not loading (D-Truck). ? ?Device Not Supported? message (D-Truck). ? Remote app inoperative (D-Truck). ? Travel-Link fuel price incorrect (D-Truck). ? Backup camera gridlines missing (D-Truck). ? Unable to adjust volume (D-Truck). ? Radio may reset/reboots, turn itself off and then back on again (D-Truck). ? High pitch squeal, pop or humming sound coming from all of the speakers (WK RU Only). ? Radio display screen is black, intermittent (RVC not affected (WK RU Only)). ? Radio freeze intermittent (RVC not affected (WK RU Only)). ? Navigation stuck on loading screen or not appearing at all (WK RU Only). ? Radios resets when a wireless connectivity paired phone receives two text messages one after another simultaneously after approximately seven seconds. (ABD sales code). ? Speaker crackling noise on non amplified vehicles (WK RU, UAV Only). ? Active cal

to damper bolts (68382486AA) when replacing the SI-eVT per TechConnect procedure. SI-eVTs built prior to January 11, 2019 had a 05192374AB level cooler. Using service SI-evT built after Jan 11 2019 with the 05192374AC level cooler requires new 68238385AB inlet hose and 68238386AC outlet hose. The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door.

please contact Zef Ivanaj at (586) 604-6738 or Neeshim Roy at (248) 512-1433 prior to replacing shifter assembly. If no response in 15 minutes, proceed with repair.

68249191A$), KL (Part # 68399021A$) and RU (Part # 68217322A$) needs to be followed. Service Instructions for the Condition of a TOC fluid leak: 1) Mark the leakage area if visible to assist in diagnosis and determination of the area where the leak has occurred. 2) If fluid leak was caused by damage or leakage at the transmission oil cooler: - Replace transmission oil cooler - Test drive and verify no additional fluid leaks 3) If fluid leak was caused by leak at quick connect fittings: - Replace transmission oil cooler lines - Test drive and verify no additional fluid leaks

to damper bolts (68382486AA) when replacing the SI-eVT per TechConnect procedure. SI-eVTs built prior to January 11, 2019 had a 05192374AB level cooler. Using service SI-evT built after Jan 11 2019 with the 05192374AC level cooler requires new 68238385AB inlet hose and 68238386AC outlet hose. The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door.

please contact Zef Ivanaj at (586) 604-6738 or Neeshim Roy at (248) 512-1433 prior to replacing shifter assembly. If no response in 15 minutes, proceed with repair.

system

Customers may experience one or more of the following:Keysense Icon/option disappears from the app/settings. Rear view camera feed stuck. Uconnect theater app, displays a black screen on radio.

Customers may experience one or more of the following:Keysense Icon/option disappears from the app/settings. Rear view camera feed stuck. Uconnect theater app, displays a black screen on radio.

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

Speaker popping, crackle noise during Voice Recognition (VR) response. Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** Lost radio presets. High pitch chime noise. Contact list not loading. Remote app inoperative. High pitch squeal, pop or humming sound coming from all of the speakers. Backup camera gridlines missing. Radios resets when a wireless connectivity paired phone receives two text messages one after another simultaneously after approximately seven seconds. (Sales Code ABD). Speaker crackling noise. Unable to adjust volume. Radio may reset /reboot, turn itself off and then back on. Active call not transferred to vehicle wireless connectivity. Voice Recognition (VR) not understanding commands. Wireless connectivity phonebook not available. Anti-theft code request message. Lines appear across screen. Radio will not switch modes between AM, FM, SAT or Media. Poor wireless connectivity sound quality. Phone pairing issues. In addition, the following enhancement is included in this update: Wireless connectivity pair or connection improvements. This bulletin involves inspecting and if required, updating the radio software level to **40.1. Depending on the radio?s current software level the radio may need a one or two USB update.**

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Library for specifications so a suitable alternative can be used

"

"

Please contact FCA REDACTED CONTENT. ~ If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Code (DTC) has been set:C2200-00 - Anti-Lock Brake Module Internal. This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this ABS update:Powertrain Control Module (PCM) Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM). Electronic Brake Booster Module (EBBM).

Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Code (DTC) has been set:B22A9-00 - ECU Internal Performance. This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this EBBM update:Powertrain Control Module (PCM) Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM). Anti-Lock Brake System Module (ABS).

Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Code (DTC) has been set:C2200-00 - Anti-Lock Brake Module Internal. This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this ABS update:Powertrain Control Module (PCM) Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM). Electronic Brake Booster Module (EBBM).

Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Code (DTC) has been set:B22A9-00 - ECU Internal Performance. This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this EBBM update:Powertrain Control Module (PCM) Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM). Anti-Lock Brake System Module (ABS).

B)

which replacement or repair of steering system components are required.