2020 Chrysler Pacifica Plug-In Hybrid TSBs

Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P0A46-00 - Drive Motor B Position Sensor 1 Circuit Range-Performance. P0A40-00 - Drive Motor A Position Sensor 1 Circuit Range-Performance. Customers may also comment on one or more of the following: Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine. 12V battery overcharged prevention. Corrected fuel consumption counter while in charge depleting. Corrections to allow the vehicle to clear the permanent fault codes. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. This bulletin involves reprogramming the **HCP and then the AHCP** with the latest available software.

Program

ordering PIM P0A78 - Drive Motor A Inverter Performance. P0A79 - Drive Motor B Inverter Performance. P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. P0A43-00 - Drive Motor A Position Sensor Circuit Intermittent. P0A45-00 - Drive Motor B Position Sensor 1 Circuit. P0C1A-00 - Drive Motor B Torque Delivered Performance.

ordering PIM P0A78 - Drive Motor A Inverter Performance. P0A79 - Drive Motor B Inverter Performance. P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. P0A43-00 - Drive Motor A Position Sensor Circuit Intermittent. P0A45-00 - Drive Motor B Position Sensor 1 Circuit. P0C1A-00 - Drive Motor B Torque Delivered Performance.

and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0111-00 - Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. (In Active or Stored status) P0071-00 - Ambient Air Temperature Sensor Performance. (In Active or Stored status) P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. (In Active or Stored status) P0073-00 - Ambient Air Temperature Sensor Circuit "A" High. (In Active or Stored status) P0011-00 - Bank 1 Camshaft 1 Position Timing Over Advanced Or. (In Active or Stored status) P25E4-00 - B Camshaft Position - Unable To Achieve Locked Position Bank 1. (In Active or Stored status) P05BD-00 - Stop-Start Mode Switch Range/Performance. (In Active or Stored status) P0116-00 - Engine Coolant Temperature Sensor 1 Performance. (In Active or Stored status) P062B-00 - Internal Control Module Fuel Injector Control Performance. (In Active or Stored status) P0604-00 - Internal Control Module Random Access Memory Ram Error. (In Active or Stored status) P060C-00 - Internal Control Module Main Processor Performance. (In Active or Stored status)** P018B-00 - Fuel Pressure Sensor "B" Circuit Range/performance. **(In Active or Stored status)** P1CEA-00 - Boost Side EVAP Purge System Performance. **(In Active or Stored status)** P06DD-00 - Engine Oil Pressure Control Circuit Performance/Stuck Off. **(In Active or Stored status)** P00C6-00 - Fuel Rail Pressure Too Low - Engine Cranking. **(In Active or Stored status)** P0300-00 - Multiple Cylinder Misfire. **(In Active or Stored status)** Customers may also experience one or more of the following: **Oil Level High Warning in the Instrument Panel Cluster (IPC).** Fully Autonomous Parking Assist (FAPA) is not deactivated when accelerator pedal is pressed. Vehicle is not heating up fast enough at freezi

illumination and the vehicle **must** SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): **P0E15-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance. P29BB-00 - Hybrid-EV Battery Pack Coolant Heater A Control Performance.** P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P0A46-00 - Drive Motor B Position Sensor 1 Circuit Range-Performance. P0A40-00 - Drive Motor A Position Sensor 1 Circuit Range-Performance. Customers may also comment on one or more of the following: **Vehicle does not start / engine does not crank. Extended engine cranking time when starting the vehicle. Engine turns on when requesting cabin heat to turn on. Loss of heat from the engine.** 12V battery overcharged prevention. Corrected fuel consumption counter while in charge depleting. Corrections to allow the vehicle to clear the permanent fault codes. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. , Special Tools, LOP and Policy sections, updated Claims Data statements, and an updated Repair Procedure. **This Technical Service Bulletin (TSB) has also been released as a Rapid Service Update (RSU) 22-100, date of issue May 28, 2022. All applicable RSU VINs have been loaded. To verify this RSU service action is applicable to the vehicle, use VIP or perform a VIN search in DealerCONNECT/Service Library. All repairs are reimbursable within the provisions of warranty. **

illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0A3F-00 - Drive Motor A Position Sensor 1 Circuit. P0A43-00 - Drive Motor A Position Sensor Circuit Intermittent. P0A45-00 - Drive Motor B Position Sensor 1 Circuit. P0C1A-00 - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: Vehicle is in limp mode.** statement, Claims Data tables,

This data collection is applicable to all vehicle with engines with sales codes: ERG, ERC, EH3 and ERF. To assist with monitoring and quality improvement of the 3.6L engine, every time a vehicle comes for any of the first 3 oil changes, please use wiTECH to record the total engine idle time and the total engine runtime. 1. Prior to perform the oil change connect wiTECH diagnostic tool. 2. Navigate to the topology screen on the action item section. 3. Once the topology screen loads, disconnect wiTECH and continue with oil change.

experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0A3F - Drive Motor A Position Sensor 1 Circuit. P0A43 - Drive Motor A Position Sensor Circuit Intermittent. P0A45 - Drive Motor B Position Sensor 1 Circuit. P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: Vehicle is in limp mode. NOTE: Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: Hybrid Control Processor (HCP). Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves servicing the transmission.

roller-finger followers (rocker arms) separately, as these are included in the camshaft parts kit.

Technician's observations can refer to spongy or stuck hydraulic lash adjusters. Exhaust lash adjusters found with a "spongy" condition (compressible plunger) leading to the assumption of being defective/malfunctioning. EXHAUST lash adjusters are designed to be COMPRESSIBLE by hand. Intake lash adjusters found with a stiff or stuck condition (non-compressible plunger) leading to the assumption of being defective/malfunctioning. INTAKE lash adjusters are designed to be NON COMPRESSIBLE by hand. Do Not Replace EXHAUST lash adjusters when the following condition is present: should be compressible, but they will exert a reactionary spring force during compression and return to full expansion without a compression force. Do Not Replace INTAKE lash adjusters when the following condition is present: should feel very firm and difficult to compress. Once the correct functioning of the intake and exhaust lash adjusters is validated with the procedure above, refer to the Service Manual "HYDRAULIC LIFTER(S) NOISE DIAGNOSIS" procedure. After the corresponding service procedures from the Service Manual involving the Lash Adjusters have been conducted, refer to the detailed instructions in the Service Manual to diagnose and/or service any other component.

Powertrain Mounting Neutralization Procedure. Discussion: Service information is in the process of being updated to include powertrain mount installation best practices. The new procedure will neutralize the mounts to lessen or remove unwanted mount tension that can lead to vibration complaints.

experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0A3F - Drive Motor A Position Sensor 1 Circuit. P0A43 - Drive Motor A Position Sensor Circuit Intermittent. P0A45 - Drive Motor B Position Sensor 1 Circuit. P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: Vehicle is in limp mode. NOTE: Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: Hybrid Control Processor (HCP). Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). REPAIR SUMMARY: **This bulletin involves servicing the transmission.**"

These conditions may be related to worn intake camshaft high lift lobe(s), and intake rocker arm(s) high lift slider. High mileage failure (10,000-60,000 miles). 1. Remove the valve cover(s) per the released service procedures. The use of a stethoscope or DTC specific cylinder misfire codes can help to locate the condition to the left or right bank. 2. Once it has been visually confirmed that there is wear on the high lift intake lobe(s) & rocker arm(s) slider, there is a special service kit for this type of repair which should be used, instead of replacing the complete engine/long block. This kit contains the parts required for the repair (intake cam, rocker arms, sealer and gaskets)."

experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0A3F - Drive Motor A Position Sensor 1 Circuit. P0A43 - Drive Motor A Position Sensor Circuit Intermittent. P0A45 - Drive Motor B Position Sensor 1 Circuit. P0C1A - Drive Motor B Torque Delivered Performance. Customers may also comment on the following: Vehicle is in limp mode. NOTE: Module flashes are also required for this Repair Procedure to be effective, the following modules are to be updated: Hybrid Control Processor (HCP). Auxiliary Hybrid Control Processor (AHCP) also known as the Power Inverter Module (PIM). This bulletin involves replacing the transmission."

installed in the vehicle.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.

(ETL, ETM, ETN Engines)

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs.P0A2D-00 - Drive Motor ?A? Temperature Sensor ?A? Circuit High. P0A33-00 - Drive Motor B Temperature Sensor 1 Circuit High. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Three modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this PCM update:Electronic Brake Booster Module (EBBM). Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as Power Inverter Module (PIM).

reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1AF8-00 - MCPA Control Module Shutdown Performance. P1AFE-00 - MCPB Improper Shut Down.P1AF8-00&P1AFE-00 will now be set as a 1 trip failure instead of a 2 trip failure. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P0A46-00 - Drive Motor B Position Sensor 1 Circuit Range-Performance. P0A40-00 - Drive Motor A Position Sensor 1 Circuit Range-Performance. This software release includes the following software enhancement:12V battery overcharged prevention. Corrected fuel consumption counter while in charge depleting. Corrections to allow the vehicle to clear the permanent fault codes. Three modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this HCP and AHCP update:Electronic Brake Booster Module (EBBM) Powertrain Control Module (PCM)

(ETL, ETM, ETN Engines)

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0EDD-00 - Hybrid/EV Battery Pack "B" Deterioration. P0BBE-00 - Hybrid Battery Pack Voltage Variation. P1C5E-00 - Battery State Of Health Failed. NOTE: Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage This bulletin involves replacing the high voltage battery pack.

illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0EDD-00 - Hybrid/EV Battery Pack "B" Deterioration. P0BBE-00 - Hybrid Battery Pack Voltage Variation. P1C5E-00 - Battery State Of Health Failed. NOTE: Any warranty qualifying issues outside of these specific DTCs will continue to be covered per the HV battery standard warranty coverage This bulletin involves replacing the high voltage battery pack.

Tire Pressure Sensors Values Are Not Displayed

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may notice one or more of the following DTCs have been set: P0AA1-00 - Hybrid/EV Battery Positive Contactor ?A? Stuck Closed. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. P0B3C-00 - Hybrid/EV Battery Voltage Sense 1 Circuit Performance. P0B41-00 - Hybrid/EV Battery Voltage Sense 2 Circuit Performance. P0B46-00 - Hybrid/EV Battery Voltage Sense 3 Circuit Performance. P0B4B-00 - Hybrid/EV Battery Voltage Sense 4 Circuit Performance. P0B50-00 - Hybrid/EV Battery Voltage Sense 5 Circuit Performance. P0B55-00 - Hybrid/EV Battery Voltage Sense 6 Circuit Performance. P1A16-00 - Hybrid/EV Wakeup Control 3 Output Circuit/Open. P1D7B-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Battery. P1D7C-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Ground. Customer may also experience one or more of the following: Premature oil change message displayed on the cluster and vehicle may be running in fuel/oil refresh mode. Scheduled charging not functioning properly because the battery pack did not wake up while plugged in.

S2623000040.

S2623000040.

Mirror Contacts Door Window Glass In The Folded Position.

Mirror Contacts Door Window Glass In The Folded Position.

Mirror Contacts Door Window Glass In The Folded Position.

Mirror Contacts Door Window Glass In The Folded Position.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

this is normal and not a defect.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

semi and full synthetic oils.

The customer may report an abnormal noise from the front or rear of the vehicle when stopped, or when accelerating at speeds below 40 kph (25 mph) (in drive) and speeds below 11 kph (7 mph) (in reverse).

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed. Rev A

Will Not Open/ Close. Liftgate/Hatch Ajar Message Displayed.

Function.

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

published document)

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Library for specifications so a suitable alternative can be used

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle.

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle

Power surge on USB hub detected Fig. 1. NOTE: After the message appears, no USB devices function in the hub (no charging, no data). NOTE: Hub operation does not return until the vehicle undergoes a full key cycle

B1A17-00 in The Radio Frequency Hub (RFH)

"

"

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Multiple Warning Indicators On In The IPC. ESM - PRNDL Flashing. And The Vehicle Will Not Shift Into Gear. The Wipers May Be On, With An Electric Parking Brake Unavailable.

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

A (XE1) eFlite Si-eVT Transmission Certain 2017 - 2023 Chrysler Pacifica (RU)

A (XE1) eFlite Si-eVT Transmission Certain 2017 - 2023 Chrysler Pacifica (RU)

system

TPM Lamp On.

TPM Lamp On.

B)

reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Three modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this HCP and AHCP update:Electronic Brake Booster Module (EBBM) Powertrain Control Module (PCM)

which replacement or repair of steering system components are required.