2021 Chrysler 300 TSBs

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

following: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.82F to QR40.12. NOTE: National launch for this FOTA update is expected to begin Feburary 19, 2024.

Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.2 to QR40.11. NOTE: National launch for this FOTA update is expected to begin February 19, 2023.

? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from Q339.3 to QR39.62. NOTE: The National launch for this FOTA update campaign is expected to begin December 04, 2023.

? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.

following symptoms: ? Mobile Wi-Fi inoperative upon start up. ? Hotspot gives "No Internet" connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.6 to QR40.12. NOTE: National launch for this FOTA update is expected to begin November 06, 2023.

? Hotspot gives "No Internet" connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.62 and QR39.57 to QR40.12. NOTE: National launch for this FOTA update is expected to begin August 16, 2023

? Hotspot gives 9No Internet9 connection message on phone, when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from QR39.7 to QR40.12. NOTE: National launch for this FOTA update is expected to begin March 10, 2023. DISCUSSION: Vehicles sold in the U.S. and Canada can now receive software updates ?over-the-air?. Updates to software will occur in a phased roll-out. The software is updated through the built-in cellular modem in the radio.

Hotspot gives 9No Internet9 connection message on phone when trying to connect to a device. This bulletin provides information regarding the latest Firmware Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The radio software will be updated from 39.5 to 40.12.

the issue per STAR Online S228A000032 before ordering a radio. You can contact FCA Redacted Content for further assistance.

39.5 Customers may experience one or more of the following: Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative. In addition, the following enhancement are included in this update:Enables map updates.

39.5 Customers may experience one or more of the following: High pitch squeal, pop or hum from all speakers. SXM favorite, displays empty song list. Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative.

published document)

published document)

39.5 Customers may experience one or more of the following: High pitch squeal, pop or hum from all speakers. SXM favorite, displays empty song list. Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative.

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

Follow Service Diagnostics published prior to making any changes. Review any existing SOL or TSBs published for customer complaint issue. Only the Fuel Pump Module should be replaced if there are DTCs associated with the Fuel Level Sensor number 1. Only the Auxiliary Level Sender should be replaced if there are DTCs associated with the Fuel Level Sensor number 2. If there is a mixture of DTCs between the Fuel Pump Module and the Auxiliary Level Sensor, then investigate if there is a Jumper Harness or circuit issue between the Level Sender and the PCM. Verify fuel transfer between auxiliary tank and the primary tank by monitoring the auxiliary level sensor to verify it drops after driving.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Tire Pressure Sensors Values Are Not Displayed

and PDM with the latest available software. This software is for vehicles on the RRT VIN List is to improve the function and reliability of the power windows operation.

Tire Pressure Sensors Values Are Not Displayed

Tire Pressure Sensors Values Are Not Displayed

and PDM with the latest available software. This software is for vehicles on the RRT VIN List is to improve the function and reliability of the power windows operation.

Upon further investigation, one or more of the following fault codes may be set in the PCM:

The technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:B18BA-12 - Window Control - Circuit Short to Battery B18BA-13 - Window Control - Circuit Open In addition the customer may notice one or more of the following:Driver and/or passenger windows stop working. If the window switch is held in the up position for at least two seconds,the obstruction autodown function may not work. Windows may go up slower than expected.

If no response within 15 minutes, proceed with repair. Please document concern, diagnosis and correction well on repair order or for a possible follow-up call to clearly understand the issue.

Upon further investigation, one or more of the following fault codes may be set in the PCM:

and PDM with the latest available software. This software is for vehicles on the RRT VIN List is to improve the function and reliability of the power windows operation.

The technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:B18BA-12 - Window Control - Circuit Short to Battery B18BA-13 - Window Control - Circuit Open In addition the customer may notice one or more of the following:Driver and/or passenger windows stop working. If the window switch is held in the up position for at least two seconds,the obstruction autodown function may not work. Windows may go up slower than expected.

If no response within 15 minutes, proceed with repair. Please document concern, diagnosis and correction well on repair order or for a possible follow-up call to clearly understand the issue.

Replacements

Replacements

Inspect & check all electrical connections to the alternator a. 2-way connector containing field control circuit & alternator sense voltage circuit. b. Unplug & plug-in the 2-way connector for field & sense circuit. Verify the connection is tight & check for any bent pins in alternator connector or damage to female terminals in connector. c. Check Alternator B+ Stud connection to be sure nut is securing positive cable terminal properly (i.e. nut is clamping terminal & connection is tight). d. Check fuse between the alternator B+ stud & PDC terminal to make sure it is not blown. e. Be sure to follow service manual sections on ALTERNATOR CONTROL CIRCUIT DIAGNOSTIC & ALTERNATOR SENSE CIRCUIT DIAGNOSTIC looking for any opens & shorts (to ground or battery voltage). 2. Check/verify all grounds in the charging system circuit a. Check tightness of mounting bolts securing alternator to engine block. Alternator is a case ground component. b. Check main ground from engine to chassis; connection must be tight. c. Check battery ground cable connections are tight. d. Potentially, loosen alternator mounting bolts, without removing alternator, and re-tighten to torque specifications in service manual. e. After all steps above are complete, re-start engine & check charging system operation. 3. Verify that the Smart Charging System is not the reason for alternator low voltage & current output (Amps). a. Alternator charging can be suspended during engine idle operation because of the Smart Charge strategy. b. Refer to service manual section ""System Operation - Smart Charging System"". c. Refer to Star Case S2008000031 Rev A for low charging voltage & Smart Charge Mode Voltage Range diagram & mode descriptions. d. The alternator has no internal regulator; thus, has no smart circuitry. All alternator control signals come from ECM. 4. If alternator is faulty, remove alternator & mounting bolts. Return alternator with bolts for analysis at QEC."

body replacement."

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P203E-00 - Reductant Level Sensor 1 Circuit Intermittent-Erratic. This bulletin involves replacing the urea delivery module and grade vent valve and updating the Dosing Control Unit (DCU) software.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** Wireless connectivity pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXMT icon inoperative. SXMT favorite song not displaying/playing. High pitch squeal, pop or hum noise from speakers. Anti-theft code request message. Lines appear across screen. Radio will not switch modes between AM, FM, SAT or Media. Performance control home screen shows ?Norm? mode for engine/transmission even when the vehicle is in ?Drag? mode (LA, LD, LX only). Can not change the time on the clock (LA, LD and LX only). USB hub inoperable (D-Trucks only). Backup camera gridlines missing (D-Trucks only). Device not supported message (D-Trucks only). Remote app inoperative (D-Trucks only). Unable to adjust volume (D-Trucks only). Heated steering wheel inoperable (D-Trucks only). In addition, the following enhancement are included in this update: CarplayT connectivity improvements. Improvement to wireless connectivity phone pairing. Improved sound quality when using a wireless connectivity phone. **This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.**

installed in the vehicle.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

39.5 Customers may experience one or more of the following: Performance control home screen shows "Norm" mode for engine/transmission even when the vehicle is in "Drag" mode. High pitch squeal, pop or hum from all speakers. SXM favorite, displays empty song list. Intermittent, black radio display screen. Intermittent, radio freezes. Bluetooth pairing and/or connection issues. Lost radio presets. Radio channels change by itself. SXM icon inoperative.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

Technician may find DTC?s B18BA-12 - Window Control - Circuit Short to Battery, B18BA-13 - Window Control - Circuit Open (stored or active). Replace the DDM or PDM per detailed repair information in Service Library or reference Star Online Publlication S2008000182. Replacing regulators or motors will not correct this issue.

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch.

used as the reason for unit replacement. Visible ""glitter"" or debris in the pan does not justify complete unit replacements."

have at least 11,265 km (7,000 mi.) and exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):** P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear This bulletin involves replacing the D clutch."

available, and transmission replacement is NOT required. Please reference TSB 21-009-25 Rev. A, for details on D-clutch replacement. Please also note, fluid color/condition/odor is NOT an indicator of transmission health and should not be used as the reason for unit replacement. Complete unit replacements instead of repairs for these DTCs may be subject to chargeback."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear. This bulletin involves replacing the D clutch"

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. **Customers may also comment on one or more of the following: Transmission slips when shifting. Vehicle will not move in reverse. Vehicle will not shift higher than third gear.** This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch"

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch. "

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits.

the Carrier Output Shaft is missing 2 seals for some of the kits delivered to dealers. These seals are not available individually. MOPAR is working to get the parts. Do not rebuild the transmission without these seals otherwise the vehicle will not have reverse. Please refer to STAR Online Publication S2421000001 for instructions for inspecting if the seals are present on the Output Shaft Carrier Shaft. If seals are missing, please return the D-Clutch Kit as defective and order another kit. Transmission replacement is not recommended as this issue should be solved with replacement kits

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0733-00 - Gear 3 Shift Incorrect Ratio. P1DA8-00 - Incorrect Gear Ratio Clutch A B or D Defective. P1D92-00 - Incorrect Gear Ratio - Clutch 4 Defective. This bulletin involves replacing the D clutch."

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set. ? P0729-00 - Gear 6 Shift Incorrect Ratio. Other software enhancement: ? Improved vehicle downshift and coast down performance. This bulletin involves reprogramming the TCM with the latest available software.

? Speaker popping, crackle noise during Voice Recognition (VR) response and navigation guidance. ? Mobile Station Integrated Services Digital Network (MSISDN) missing from radio, no connected services working.** ? Intermittent, black radio display screen (Rear View Camera (RVC) not affected). ? Intermittent, radio freezes (RVC not affected). ? Wireless connectivity pairing and/or connection issues. ? Lost radio presets. ? Radio channels change by itself. ? SXMT icon inoperative. ? SXMT favorite song not displaying/playing. ? Incorrect navigation address/location/directions. ? Backup camera has black display screen or only displays Check Entire Surroundings with black screen (occurs when vehicle is shifted immediately to reverse upon key-on before RVC signal is received, recoverable with key cycle) . ? High pitch chime noise. ? Contact list not loading. ? Device not supported message. ? Remote app inoperative. ? Travel-Link fuel price incorrect. ? Backup camera gridlines missing. ? Unable to adjust volume. In addition, the following enhancement are included in this update: ? Enables map updates. ? Heavy Duty (HD) Truck USB HUB improvements. ? HD Truck heated steering wheel improvements This bulletin involves inspecting and if required, updating the radio software level to 40.1. Depending on the radio?s current software level the radio may need a one or two USB update.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs): U0101 - Lost Communication With TCM. U0102 - Lost Communication With Transfer Case Control Module / AWD. U0103 - Lost Communication With Electric Gear Shift Module. U0104 - Lost Communication With Cruise Control Module. U0125 - Lost Communication With Dynamics Sensor. U0128 - Lost Communication With Park Brake Control Module. U0129 - Lost Communication With Brake System Control Module 1. U0140 - Lost Communication With Body Control Module. U0141 - Lost Communication With Ipm (BCM). U0155 - Lost Communication With Cluster-CCN. U0159 - Lost Communication With Parking Assist Control Module. U017E - Lost Communication With Seatbelt Sensor 1. U0293 - Lost Communication With Hybrid Control Module. U0402 - Implausible Data Received From TCM. U0403 - Implausible Data Received From Tcase. U0405 - Invalid Data Received Cruise Control Module. U0416 - Implausible Data Received From ESP. U0418 - Implausible Data Received From Brake System Control Module 1. U0429 - Implausible Data Received From SCM. U0432 - Invalid Data Received From Multi-Axis Acceleration Sensor Module. U0594 - Implausible Data Received From HCP. U110A - Lost Communication With SCM-CAN-C. U1110 - Lost Vehicle Speed Message. U1120 - Lost Wheel Distance Message. U1141 - Lost ESP Torque Request Message. U1186 - Lost Communication With Adaptive Cruise Control Module. U11BC - Lost Brake Switch Message. U11C2 - Lost Transmission Message. U11DE - Lost Speed Control Message. U145D - Implausible Data Received From TCM On D-PT. Customers may also experience one or more of the following:Loss of shifting and or fixed third gear operation. Loss of Anti-lock Brake System (ABS), Traction Control System (TCS)

this is normal and not a defect.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

semi and full synthetic oils.

Detected Message

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

Detected Message

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

Blind Spot Indicator On In Mirror For No Reason.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.

When customer comes in for a cracked windshield, please note the location of crack and take pictures before repair. Please send pictures to FCA Redacted Content or load to the warranty claims system.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order"68" part number for New unsold units only

Library for specifications so a suitable alternative can be used

Cameras must be inoperative or fail the blurry image test to be eligible for warranty. All parts must be returned for analysis. If parts are found to be working as designed and trouble not found, a chargeback may be applied. Prior to camera replacement, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

DO NOT remove actuators 2. Verify noise by cycling EEV manually via WiTech 3. Verify noise with test drive (optional) 4. If the noise is confirmed, replace the system without removing the actuators.

system

B)

which replacement or repair of steering system components are required.