2017 Chrysler 200 TSBs

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block."

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

pressure low indicator lamp illumination between oil changes. ? Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

pressure low indicator lamp illumination between oil changes. Excessive oil consumption. This bulletin involves performing an oil consumption verification test and possibly replacing the long block.

2015 - 2018 Jeep Renegade (FWD/AWD) (BU), 2013 - 2016 Dodge Dart (PF), 2015 - 2017 Chrysler 200 (UF), 2016 - 2018 Fiat 500X (FWD) (FB), (AWD), 2015 - 2018 Ram Promaster City (VM)

installed in the vehicle.

oil between oil change intervals and no visible signs of oil leaking from the engine. This bulletin involves performing an oil consumption verification test.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.

engines, please note that there is a new diagnostic procedure available in DealerCONNECT for P-codes in relationship to cam phasers. Please use this new information for trouble shooting of cam phasers and oil control valves for MIL on issues.

Engine only: Oil leaking from the valve cover onto the O2 sensor causing faults codes P0140, P2096, P0137, P0157. Need to verify the leak source and cause (gasket pinched, out of position, rolled, or cut). Please call one of the individuals below before proceeding with the repair. Also, if possible take a picture and send it to the emails listed below. First: Scott Knaggs - Cell (313) 363-6937 scott.knaggs@facgroup.com Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair.

(OFA) due to a leak detected between OFA and block. Ensure the torque on the 5 (OFA) bolts are torqued to 12nm.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

installed in the vehicle.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

The customer may comment that the vehicles engine oil level is low or they need to add oil between oil change intervals and no visible signs of oil leaking from the engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find thatone or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0300 - Multiple Cylinder Misfire P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. Some customers may also experience the following condition:Rough running engine.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

(OFA) due to a leak detected between OFA and block, an O-ring kit (68191356AA) is now available to repair OFA/Block Interface leaks. Using dye will assist in determining source of leak. Ensure OFA Cap Oring is seated in the proper groove in the cap and not damaged or cut. Engineering is seeking information regarding OFA leaks. Questions/info can be directed to: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Ron Dallison Cell (248-292-9510) ron.dallison@fcagroup.com Joe Lovell Cell (734) 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.

Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.

The gaskets are not required by warranty to be replaced like they are on Pentastar Classic (ERB/EHB). The new gaskets are not interchangeable with Pentastar Classic Intake Manifold Gaskets.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Customers may experience one or more of the following:Radio functions/touchscreen locks up (does not affect backup camera). Phone presets do not save. ?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 only). Poor or no connection to cellular network. ?Charge Complete? notification is not received (RU PHEV only). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. Improvements:Auto Play can now be configured. Media devices, Phone pairing and Bluetooth usage improvements. Add the ability to drag and drop icons into the menu bar. Adds ?Do Not Disturb? text message feature. Fix for radio locks up/frozen. Enhanced Voice recognition (VR) performance. Improved tuner performance. Human Machine Interface (HMI) improvements. Satellite radio reception improvements.

Customers may experience one or more of the following:Radio functions/touchscreen locks up (does not affect backup camera). Phone presets do not save. ?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 only). Poor or no connection to cellular network. ?Charge Complete? notification is not received (RU PHEV only). Some Uconnect App remote commands do not execute with the vehicle. Radio Apps are inoperative. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. Improvements:Auto Play can now be configured. Media devices, Phone pairing and Bluetooth usage improvements. Add the ability to drag and drop icons into the menu bar. Adds ?Do Not Disturb? text message feature. Fix for radio locks up/frozen. Fix for radio loses time. Enhanced Voice recognition (VR) performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Human Machine Interface (HMI) improvements. Satellite radio reception improvements.

harness in the front seats if needed. Customers may experience a AWL illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in memory:B0028-13 - Right Side Seat Deployment Squib 1 - Circuit Open. B0020-13 - Left Side Seat Deployment Squib 1 - Circuit Open.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

harness in the front seats if needed. Customers may experience a AWL illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in memory:B0028-13 - Right Side Seat Deployment Squib 1 - Circuit Open. B0020-13 - Left Side Seat Deployment Squib 1 - Circuit Open.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

radio FOTA (Firmware Update Over the Air) has been completed, please DO NOT replace the radio. To recover the radio, 12v power needs to be disconnect from the radio to clear radio memory either by removal of the radio fuse or preforming a battery disconnect. Note: Fuse removal is the preferred method. The radio needs to be disconnected from power long enough to clear memory and discharge the Capacitance within the radio. Please refer to the latest in diagnostics for further information.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

If the radio is locked up, has a blank screen, or no sound, please perform a vehicle battery reset. If radio functionality is resumed, return the vehicle to the customer. If there are any questions or concerns or the vehicle has been in for repair for the same radio concern more than once, please call Rick Gordon at Cell (248) 630- 6281. If no response in 15 minutes, proceed with repair.

Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

refinishingthe suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.

stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

this is normal and not a defect.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

semi and full synthetic oils.

as a separate part number in the kit which is 04753095AB.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

awareness regarding the use of aftermarket parts.

structural repair parts usage.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

18.01.35 (BU Vehicles)

Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update.

Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. The following improvements are included in this update:Fix for sport mode not working in the performance menu page (2015 LA equipped with 6.4L and 5.7L Sales Codes ESH and EZC Only). Adds Apple Siri Eyes Free capability for iPhone owners. Auto Play can now be configured. Adds do not disturb text message feature. The ability to drag and drop icons into the menu bar. Fix for radio locks up/frozen. Fix for stuck on black/blank screen. Human Machine Interface (HMI) improvements. Several navigation improvements. Fix for radio loss of time display. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhanced Voice recognition (VR) performance. Enhancements in Connectivity Apps (Yelp, Pandora, Aha, etc).

If no response in 15 minutes, proceed with the repair.

technician an overview of the steps a customer will need to take to complete the update.

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Print I-Sheet for technician use.

new guideline states that the tether anchor can be used with a seatbelt to install a child restraint up to the recommended weight limit of the child restraint.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

new guideline states that the tether anchor can be used with a seatbelt to install a child restraint up to the recommended weight limit of the child restraint.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

refrigerant leak at the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet. CONDITION 2: For stock at the dealership of the below Part Number level or older ONLY, use kit 68447796A$ to change the desiccant BAG and the desiccant bag access PLUG before installing the Cooler on the vehicle. 52014588AD level and older only. 52014609AC level and older only. 52014632AC level and older only. 52014797AG level and older only. 52014948AE level and older only. 52014978AF level and older only.

the receiver/drier plug on the A/C condenser, order the receiver/drier plug kit P/N 68447796A$ and follow the repair instructions included on the instruction sheet.

illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): P1DB7-00 - Torque Converter Clutch Performance.

Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

(248) 613-7488 prior to working on the unit. If Jason cannot be reached within 15 minutes proceed with the repair.

Library for specifications so a suitable alternative can be used

B)

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.

Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

which replacement or repair of steering system components are required.

Visual Inspection--> Check if the sensor is visually OK. (all the pins are OK) Check that the Connector is NOT loose (Sensor must get a voltage from 9V to 16V) 2. Functional Checks Rain--> Steering column switch is in auto mode (sensor is active) it is necessary to splash water on the sensitive surface of the sensor to trigger wipes. check the same for different sensitivities When the rain sensitivity is increased (for example from level 0 to level 1), as an acknowledgement a single wipe is seen. (This is not a phantom wipe) and this single wipe is not seen when the rain sensitivity is decreased (from higher level to lower level) Light--> Steering column switch is in auto mode (sensor is active) block the light coming on the sensor from outside of the vehicle (use a opaque object), the head lamps should be activated 3. If the sensor seems functional, it is ideal to remove the silicon gel pad from the sensor, replace it with the new silicon gel pad instead of replacing the whole sensor. When servicing the LRSM please replace the silicon gel pad with a new silicon gel pad (PN 68224945AA) instead of replacing the whole sensor.