2012 Chrysler 200 TSBs

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY review and follow instructions from the latest STAR Online S1809000007 available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

installed in the vehicle.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold For concerns of V8 oil filter leaks on 22MY and up vehicles: 1. Clean the area and use oil dye to know the exact location of the leak with black/UV light. 2. Removal torque (force needed to loosen the filter) 3. If the source of the leak cannot be identified, please contact FCA Redacted Content to FasTrak parts back for analysis. If no response in 15 minutes, proceed with repair and email pictures of the following: A) Oil filter from the bottom to know if it has a "Factory Installed" filter. B) Leak. C) Damage in filter (if any) D) Gasket. E) Block or Oil Filter Adapter(OFA) or Engine Oil Cooler(EOC) sealing surface.

engines, please note that there is a new diagnostic procedure available in DealerCONNECT for P-codes in relationship to cam phasers. Please use this new information for trouble shooting of cam phasers and oil control valves for MIL on issues.

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following DTCs have been set: U0140 - Lost Communication With Body Control Module. P0441 - EVAP Purge System Performance. P0420 - Catalyst Efficiency (Bank 1). P0430 - Catalyst Efficiency (Bank 2). P0133 - O2 Sensor 1/1 Slow Response. P0153 - O2 Sensor 2/1 Slow Response. P0300 - Multiple Cylinder Misfire. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P113D - O2 Sensor 1/1 Slow Response (High Frequency). P113E - O2 Sensor 2/1 Slow Response (High Frequency). P0108 - Manifold Absolute Pressure Sensor Circuit High. P0606 - Internal Control Processor. P0204 - Fuel Injector 4 Circuit/Open.In addition, the customer may notice the following conditions: 1 - 2 upshift clunk or bump. 4 - 5 upshift clunk or bump. 5 - 6 upshift clunk or bump. 6 - 5 downshift clunk or bump. 6 - 4 downshift clunk or bump. RPM fluctuating or jerking feeling while operating in cruise control. Condition is more noticeable when the vehicle is going up and down grades. A less than desired idle speed after performing a hard braking maneuver.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

installed in the vehicle.

To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - Feb 28, 2019 VF. - Only use R8453637A$ or R8599680A$ for March 1, 2019 and later VF as they have the revised park system. - R8453637A$ and R8599680A$ are physically and functionally equivalent. Installing a R8453637A$ or R8599680A$ in a 2014 - Feb 28, 2019 VF will result in a core with the original park system being returned. Mopar can no longer convert 62TE core with the original park system to the March 1, 2019 and later version. Continued mis-usage will exacerbate the existing core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. Only use the reman 62TE specified in StarParts for each model year - Only use R8210327A$ for 2014 - 2018 VF. - Only use R8453637A$ for 2019 VF. - Only use R8599680AA for 2020/1VF. Installing a R8453637A$ or R8599680A$ in a 2014-18 VF will result in a 2014-18 MY core being returned. Mopar can no longer convert 2014-18 VF 62TE core to the 2019-21 version. Continued mis-usage will result in a core shortage. Mopar may deny warranty claims where the incorrect version is used in 2014-18 VF. 3. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 5. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

with leak concern: 1) Ensure the Oil Filter Adapter (OFA) Cap O-ring is seated in the proper groove in the cap and not damaged or cut. 2) If replacing the (OFA) due to a leak detected between (OFA) and block. Ensure the torque on the 5 bolts are torqued to 12nm. If not record the actual values, torque to 12nm and contact the FCA employees listed below. 3) Remove the (OFA) and replace the O-ring and gaskets only (Kit #68191356A$), NOT THE OFA. 4) If oil was drained, add oil dye to ensure the leak is repaired. For model year 2014 vehicles replace the Oil Filter Adaptor. 5) When replacing PN's 68310865A$ & 68308741A$, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.

All Promaster (VF) 3.6L/62TE equipped vehicles: a) If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) must be replaced as they are one-time usage. b) Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA. c) Vehicles built on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. The engine to transmission dowel pins are critical to the longevity of several components. Verify the dowel pins are in the rear face of engine block before installing a replacement transmission. Mopar will add loose dowel pins with remanufactured 62TE. 3. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. 4. There may be incorrect fluid measurement on the dipstick tool when checking 62TE fluid level after filling the ATF as per service library specification. Please change with new valve body pan P/N:68145886A$ as there may be incorrect valve body pan is used in Transmission.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

If replacing due to missing Spring Loaded Check Valve, a replacement spring and check valve are now available through MOPAR.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.

See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: P0300- Multiple Cylinder Misfire P0302- Cylinder 2 Misfire P0304- Cylinder 4 Misfire P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

cylinder leakage and replacing the cylinder head if necessary. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Codes have been set: ? P0300- Multiple Cylinder Misfire ? P0302- Cylinder 2 Misfire ? P0304- Cylinder 4 Misfire ? P0306- Cylinder 6 Misfire

replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.

The customer may experience one or more of the following conditions. Navigation voice prompt is now announced near maneuvers such as exit ramps. Radio freeze when playing large number of .M4A or .WMA files,and recovers with ignition cycle. Battery signal strength display is not displayed into the radio screen (with iPhone 5). Traffic Announcement and Voice Recognition share the same volume control. Traffic Announcement volume drops after phone calls. Mismatch in the ?Distance to next turn? between the radio and EVIC displays. German translations are incorrect. Radio reset when copying certain .MP3 files from USB flash drive to the radio. Radio stations info is not correct into the right side of the radio display (radio menu). Radio mute issue in tuner mode. Preset loss during/after AF Switching. Erratic alternate frequency switching. Bluetooth phone muting during European traffic announcement. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Cancel key inoperative after pressing the international button. iPhone 4 dial not possible after second call. Devices button disabled in VES menu. Unable to route to a recent route after a map update. Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of Interest (POI) Search enhancements. Devices button wrongly labeled as DVD using the remote DVD player. iPod, track selection enhancements.

Customer may describe a clicking/popping noise while turning the wheel which occurs after vehicle has been driven for a minimum of 30 minutes at above idle. Noise typically heard when driving below 25 mph or when turning steering wheel while stopped.

Customer may describe a clicking/popping noise while turning the wheel which occurs after vehicle has been driven for a minimum of 30 minutes at above idle. Noise typically heard when driving below 25 mph or when turning steering wheel while stopped.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

Please return stock packaged before 2016/07/31 (31 July, 2016)of follow ing part numbers:68176457AF, 68176459AF. Please return suspect parts back to your facing depot using Return Code 02, before 13 September, 2016.

The customer may experience one or more of the following conditions. Erratic alternate frequency switching (International only). Bluetooth phone muting during European traffic announcement (International only). Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Vehicle with Start/Stop feature, the screen will go black when the engine turns off at a stop. (International only). Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). Cancel key inoperative after pressing the international button. iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). Duplicate phone numbers in popup after pressing the international button. During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

(M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~

(PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM: **U0140 - Lost Communication With Body Control Module (BCM) (2012 MY only). P0116 - Engine Coolant Temperature Sensor Performance (2012 MY only).** P2173 - High Airflow/Vacuum Leak Detected (Slow Accumulation). The following transmission enhancements are also included in this software update: 3-2 downshift clunk or bump (2012 Sales Code DG2 only). 4-3 downshift clunk or bump (2012 Sales Code DG2 only). 1-2 upshift clunk or bump (2012 Sales Code DG2 only). 4-5 upshift clunk or bump (2012 Sales Code DG2 only). 5-6 upshift clunk or bump (2012 Sales Code DG2 only). RPM Fluctuating or jerking feeling between 96 KPH (60 MPH) to 112 KPH (70 MPH) while operating in cruise control.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands; DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Hands Free Module (and associated components) are the systems responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis. Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

Left and right outlet temperatures do not match when system is in "sync" . Occupants will experience being cold ( winter time), on either passenger or driver side, even though the temperature setting is the same. Root cause: Suspect sun senors ( PN 55111274AA and 55111275AA). THERE WILL BE NO DTC FOR THE SUN SENSOR active or stored. The issue is diagnosed by using an INCANDESCENT (not LED) shop lamp. Shine the shop lamp on the left side of the sensor, then on the right side of the sensor, while monitoring sensor output with STARSCAN. The reading should change from 0 (or near zero) to about 20 to 40. The important thing is that the left and right readings are the same, and that they change when the lamp is shone on it.

flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality ( may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the 1. Power on radio~ 2. Press MENU H/K~ 3. Press System Setup S/K~ 4. Press Manage HDD S/K~ 5. Press Display Available Space on HDD S/K~ 6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

Current plug boot material(silicone) is not compatible with this grease and can cause deterioration over time.

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

headliner fastener brackets to the headliner panels. The fastener brackets that secure the headliner panels to the roof are separating from the headliner panels. The customer may describe the headliner falling down.

occasions, the flash can fail to properly update the radio resulting in the radio running in Emergency IFS mode. This error condition can occur due to interrupting the software update, background radio operations interfering with the reflash process, etc. The radio will reboot, but with limited functionality (examples may include but are not limited to: NAV, Voice Recognition, Bluetooth, or AUX jack are inop, no available space shown on HDD, etc.). The radio can still be properly updated by simply reinserting the software update disc and performing the reflash procedure again. To assist in the verification that the radio is running Emergency IFS perform the following:~ 1. Power on radio~2. Press MENU H/K~3. Press System Setup S/K~4. Press Manage HDD S/K~5. Press Display Available Space on HDD S/K~6. When running Emergency IFS, all items under Used, Available, and Capacity report as dashes~ Issue 2: If you are having troubles connecting a phone or a MP3 player, try removing the battery on the device and then going through the pairing/connection procedure again. If you cannot remove the battery on the device, perform a reboot. Each manufacturer has a different series of buttons to hold down to perform a reboot. If the problem still persists, try the device on another like vehicle with the same radio. If you are having the same connection issues on another like vehicle, the device may be faulty or it may not be compatible with the RHR radio. Go to www.chrysler.com/hostb/crossbrand/owners/en and click on ?Bluetooth Phone Compatibility Test Results? link for a list of phones that are compatible. For MP3 players and media storage devices, only .wma, .aac, .mp3, .sacd, .jpeg & .jpg files are supported. Remove all other file types and reevaluate the concern. ~ Issue 3: If upgrading a vehicle from a low line radio that has factory installed UConnect

USB flash or replacing the Mopar accessory Hands Free Module (HFM). A customer may experience the Uconnect prompts begin to play without pressing the Voice Recognition (VR) button. The prompt may repeat itself two or three times before exiting. The customer satisfaction enhancements are included with this software release. NOTE: After the HFM has been updated it will receive these enhancements: Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via Mobile Application Part (MAP) protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected. NOTE: USB mode resume will no longer 'resume' after ignition is OFF.

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

have stock in transit to your dealership. Please return part number CBSZR068AA as per the QIR attached. Replacement part can be obtained by ordering the same part number (CBSZR068AA) Please return suspect parts back to your facing depot using Return Code 02, before 02 September, 2016.

The customer satisfaction enhancements are included with this software release:After the HFM has been updated it will receive these enhancements. Reduced ?Device Reading? wait time after connecting a device to the remote USB port. Call / Dial separation improves upon names being recognized as phone numbers. Improved sound quality during Bluetooth streaming. Increased iPod and iPhone compatibility. SMS messaging support via MAP protocol (not all phones support the MAP protocol). Added ?None of These? and ?Correction? to the phone book prompt menu for better handling of similar names. Previous button will return the song currently being played to the beginning of the track. AirPlay feature ?Dock Connector? no longer needs to be manually selected on Apple devices. This will resolve the ?No Audio? condition when the device is connected to the remote USB port and dock connector is not selected.USB mode resume will no longer 'resume' after ignition OFF

Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) are the systems responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE)

this is normal and not a defect.

this is normal and not a defect.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

semi and full synthetic oils.

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold

awareness regarding the use of aftermarket parts.

structural repair parts usage.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

receiver rod on each of the down capture latch assemblies and if necessary replacing the receiver rod along with installing a revised down capture hook assembly. The customer may experience a rattle or clunking sound coming from the convertible top while driving.

receiver rod on each of the down capture latch assemblies and if necessary replacing the receiver rod along with installing a revised down capture hook assembly. The customer may experience a rattle or clunking sound coming from the convertible top while driving.

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Please return stock of part number CBXDP361AA. Replacement part number is CBXDP361AB w hich is in stock and available for order. Please return suspect parts back to your facing depot using Return Code 02, before 16 September, 2016.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

Customers may experience a condition were new roads and new point of interests are not accurately shown on their navigation system.Updating the navigation software will help address most of the map inaccurate results.

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. SYMPTOM/CONDITION FOR RHB RADIOS ONLY: ? Trip planner does not save a route after is was created. ? Route guidance does not activate after the vehicle shuts down. ? Longitude entry does not allow enough digits. ? CD/DVD will not play. ? Navigation accept screen will not clear. ? Navigation shows ?acquiring signal? for an extended period of time. ? New navigation graphics.

The customer may experience one or more of the following. When changing the language on the radio, the navigation may still display English. Help prevent navigation lockup. Ghost image of the vehicle?s brand logo on the display screen. Digital photos loaded onto the hard drive intermittently get lost. Sirius audio pop on power up. HFM audio pop on power up. HFM Mode resume with no information.SYMPTOM/CONDITION FOR RHB RADIOS ONLY: Trip planner does not save a route after is was created. Route guidance does not activate after the vehicle shuts down. Longitude entry does not allow enough digits. CD/DVD will not play. Navigation accept screen will not clear. Navigation shows ?acquiring signal? for an extended period of time. New navigation graphics.

The customer may experience one or more of the following. ? When changing the language on the radio, the navigation may still display English. ? Help prevent navigation lockup. ? Ghost image of the vehicle?s brand logo on the display screen. ? Digital photos loaded onto the hard drive intermittently get lost. ? CD/DVD will not play (RHB only). ? Navigation accept screen will not clear (RHB only). ? Navigation shows ?acquiring signal? for an extended period of time (RHB only). ? New navigation graphics (RHB only). ? Sirius audio pop on power up. ? HFM audio pop on power up. ? HFM Mode resume with no information. ? Trip planner does not save a route after is was created (RHB only). ? Route guidance does not activate after the vehicle shuts down (RHB only). ? Longitude entry does not allow enough digits (RHB only).

The customer may experience one or more of the following conditions. Enhancements to the loss of preset condition. Lost channel presets, home addresses, address book entries & Travel Link favorites. Not able to change default country and state then route. Unable to load .jpeg files onto hard drive to display on touch screen. Incomplete Travel Link temperature displayed when the temperature is over 100F. Example, if the temperature is 107F the screen will display 07. (Domestic U.S. only). iPhone4 dial not possible after second call. Missing Travel Link buttons from SAT menu (Domestic U.S. only). Devices button disabled in VES menu. Unable to route to a recent route after a map update. Remove Travel Link disclaimer popup (Domestic U.S. only). During active call and on hold, DIAL button should be displayed (not ?TONE? button). International button not visible. Point of interest (POI) Search enhancements. When video in remote DVD player is stopped devices button wrongly labeled as DVD. Access Travel Link immediately after radio no update when staying on TL screen. iPod, track selection enhancements.

Customers may experience a condition were new roads and new point of interests are not accurately shown on their navigation system.Updating the navigation software will help address most of the map inaccurate results.

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

Customers may experience a condition were new roads and new point of interests are not accurately shown on their navigation system.Updating the navigation software will help address most of the map inaccurate results.

The customer may experience one or more of the following conditions. Digital photos loaded onto the hard drive intermittently get lost (RBZ & RHB). CD/DVD will not play (RHB only). Navigation accept screen will not clear (RHB only). Navigation shows ?acquiring signal? for an extended period of time (RHB only). New navigation graphics (RHB only).

Print I-Sheet for technician use.

A)

Avenger/Chrysler 200 (JS)

new guideline states that the tether anchor can be used with a seatbelt to install a child restraint up to the recommended weight limit of the child restraint.

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

new guideline states that the tether anchor can be used with a seatbelt to install a child restraint up to the recommended weight limit of the child restraint.

B)

A)

Avenger/Chrysler 200 (JS)

A)

Avenger/Chrysler 200 (JS)

Print I-Sheet for technician use.

Correct information sheet (I-Sheet) has been added to Star Parts. Print I-Sheet for technician use.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Please return suspect stock of part numbers: 1ZA04DX9AE, 1ZA05DX9AE. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.

stock in transit to your dealership. Please return suspect stock of part number 1N T30XDVAC. See attachments for identifying suspect stock. Replacement part can be obtained by reordering the same part number. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS (Part Number 06511385A$) ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts (8) 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only (shot peened)

This PCM software enhancement improves how the shifts are controlled during upshifts (torque management).

TRANSMISSION BRACKET TO THE TRANSMISSION CASE FASTENERS ARE REMOVED DURING SERVICING, THE FASTENERS Part Number 06511385A$ ARE ONE TIME USEAGE & MUST BE REPLACED & PROPERLY TORQUED TO 105NM Replace the eight bolts 8 06503465 drive plate to crank shaft and the four TC bolts 06504383 as they have sealants Vehicle miles < 30K: Mandatory replacement of transmission and driveplate Vehicle miles > 30K: Replace driveplate only shot peened

This PCM software enhancement improves how the shifts are controlled during upshifts (torque management).

Please return suspect stock of follow ing part numbers:52120000AA, 52119435AF, 05078709AB. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

This PCM software enhancement improves how the shifts are controlled during upshifts (torque management).

The seal kit does not come with the Distribution Housing.

catalytic converter efficiency

industry awareness regarding the use of recycled or salvage parts.

industry awareness regarding the use of recycled or salvage parts.

Please return suspect stock of part number 05182535AD . See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 12 September, 2016.

Please return all stock of follow ing part numbers:55372082AE, 55372082AD, 55372082AC, 55372082AB, 55372082AA. Replacement part number is 55372082AF w hich is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 07 September, 2016.

Order the "R" part number for all orders: Warranty, Mopar, customer pay and service contract. Order "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

which replacement or repair of steering system components are required.

Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure