2015 Chevrolet Tahoe TSBs

Dealers are to suspect/monitor the crankshaft position sensor.

internal engine damage.

repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

engine related shudder.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

GDS 2.

issue.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

consumption.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.

service or aftermarket calibrations.

GDS 2.

consumption.

occurrence.

This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.

possibilities of what may happen using the incorrect filter.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

GM has determined that wheel refinishing under warranty will no longer be performed.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

conductive finish.

parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

and improve fuel economy.

service or aftermarket calibrations.

the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

housing and to perform testing on transmission for other possible issues, but it still may be possible on high mileage vehicles that orifices in housing may have come dislodged, causing the same customer concern.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

Dealers Only).

Recommendations.

consumption.

Dealers Only).

possibilities of what may happen using the incorrect filter.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.

service or aftermarket calibrations.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

GDS 2.

engine related shudder.

consumption.

driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

issue.

issue.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

service or aftermarket calibrations.

internal engine damage.

Dealers Only).

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

housing and to perform testing on transmission for possible other issues, but it still may be possible on high mile vehicles that orifices in housing may have come dislodged, causing the same customer concern.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

lose audio except warning chimes and become inoperative after using Siri. The concern may be corrected by an ignition cycle. If the radio continues to be inoperative please contact General Motors Technical Assistance for further direction.

gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

GDS 2.

Identification.

consumption.

service or aftermarket calibrations.

internal engine damage.

engine is started while diagnosing for noise from the engine or transmission.

which will need to be installed to correct the repair.

Recommendations.

and improve fuel economy.

engine related shudder.

Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

Dealers Only).

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

Turbochargers Returned to Warranty Part Center.

Dealers Only).

or the vehicle has sat for a few hours.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

service or aftermarket calibrations.

failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

engine related shudder.

after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).

occurrence.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

and19368176where the incorrect crankshaft timing gear was installed. Provides dealer with information to correct this condition.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

key option Regular Production Option Code 6E2 or 6E8. Technician will need to check the Regular Production Option Code for 6E2 or 6E8. Technician will need to order the correct key part number per the Regular Production Option Code. Then the technician will need re-code the lock cylinders to match the Regular Production Option Code. Also replace the Body Control Module and normal Service Programming System to the Body Control Module will turn the vehicle to a common key.

may be noisy or vibrate when running. This concern will only occur when the temperatures is below 32 degrees Fahrenheit and if the blower motor is removed while still cold, ice may be found on the blower motor cage. This concern could be caused by water leaking or snow ingestion into the Heater-Vent-Air Conditioning case. Technician is to perform normal water testing diagnostics while the Heater-Vent-Air Conditioning is running, looking for water leaking past the plenum cover. If water is leaking past the cover remove the cover and install a 12x12 snow resistant screen to the fresh air intake. Reseal and install the plenum cover cap using Kent air dry sealer or equivalent.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

and19368176where the incorrect crankshaft timing gear was installed. Provides dealer with information to correct this condition.

cylinders after the camshaft was replaced.The camshaft may have been boxed incorrectly

Dealers Only).

and improve fuel economy.

Dealers Only).

and improve fuel economy.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.

internal engine damage.

occurrence.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

eliminate coolant smell and/or a slight leak at the radiator.

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

GDS 2.

engine oil consumption.

Dealers Only).

Drive concern.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

GDS 2.

engine oil consumption.

Dealers Only).

Drive concern.

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

Identification.

vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection.If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

Chevrolet Suburban, Chevrolet Tahoe, GMC Sierra, and GMC Yukon vehicles may have a condition where customers may experience increased brake pedal effort, hard brake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applying the brakes. The engine mounted mechanical vacuum pump output may decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervals could contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5 minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs, the hydraulic brake system remains functional but may require additional pedal force. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.

service or aftermarket calibrations.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

found the cause of the customers concern.

replace the pistons if found the cause of the oil consumption.

failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.

Dealers Only).

White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

replace the pistons if found the cause of the oil consumption.

transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

8L90 transmission the vehicle will not move the valve body may be missing a plug and retainer bolt. Technician's are instructed to obtain and installa plug and retainer bolt kit from the GM Warranty Parts Center to address this concern.

repairing vehicles that may have unwanted grade braking, reduced engine power with no Driver Information Center messages ? Brake Pedal Override Feature ?, transmission busy or frequent shifting up or down, and Diagnostic Trouble Codes P057B, P057C, and/or P057D may or may not be set. Technician will use this preliminary information to find the brake pedal position data parameters in the scan tool, and also to provide some additional diagnostic help. These issues may be caused by an incorrect brake pedal position sensor input to the engine control module. Technician will verify with the scan tool if the engine control module has the correct parameters for the brake pedal position sensor. If an engine control module brake pedal position sensor relearn is performed, the truck may be temporarily repaired until the intermittent wiring issue between the engine control module and brake pedal position sensor occurs again. On 2014 and newer trucks inspect and repair any damage to X115 and X119. On the 2014 and previous trucks inspect and repair any damage to X205.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

Drive concern.

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

or the vehicle has sat for a few hours.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

key option Regular Production Option Code 6E2 or 6E8. Technician will need to check the Regular Production Option Code for 6E2 or 6E8. Technician will need to order the correct key part number per the Regular Production Option Code. Then the technician will need re-code the lock cylinders to match the Regular Production Option Code. Also replace the Body Control Module and normal Service Programming System to the Body Control Module will turn the vehicle to a common key.

Dealers Only).

customers concern of engine misfire, ticking noise and/or MIL Illuminated.

or the vehicle has sat for a few hours.

Trailer Brake message in the Driver Information Center. Also the vehicle will have a Diagnostic Trouble Code U0415 set. Technician will fill the master cylinder brake fluid reservoir to the maximum level.

General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.

occurrence.

guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

customer concerns related to wheel alignment.

has been sheared away to correct a crank/No Start condition.

correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.

overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.

repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped

factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).

caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.

has been sheared away.

Package Vehicle and Special Service Vehicle have four relay controlled circuits which can be utilized when installing special first responder equipment. Please reference the latest version of General Motors Upfitter Integration Bulletin 118 for additional information on these circuits.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection.If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.

Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

engine oil consumption.

transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.

Certain Vehicles may have a condition where customers may experience increased brake pedal effort, hardbrake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applyingthe brakes. The engine mounted mechanical vacuum pump outputmay decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervalscould contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs,the hydraulic brake system remains functional but may require additionalpedal force. Please be aware that even if the vehicle exhibits this condition, it meets all federal motor vehicle safety standards forbrake performance. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.

repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold. If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.

On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio. On 1500 series trucks and all sport utility vehicle with regular production option code IO4, IO5, or IO6 the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface. On 2500/3500 series trucks production option code IO3 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio. On 2500/3500 series trucks production option code IO4, IO5, or IO6 radio the ambient air temperature sensor is hard wired to the instrument panel cluster and then the signal goes on low speed local area network to the radio then Most 50 Bus to the Human Machine Interface.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

Drive concern.

alignment pin has been sheared away.

that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.

after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

Certain vehicles equipped with special service package (RPO 5W4) and certain 2015 ? 2019 Chevrolet Tahoe vehicles equipped with police package (RPO 9C1) or special service package (RPO 5W4) may have a condition in which frequent, repeated brake applications at low speed or idle speeds can deplete available brake vacuum assist faster than vacuum can be replenished by the system, which can lead to increased brake pedal effort, hard brake pedal and potentially increased stopping distance. These vehicles utilize Hydraulic Brake Boost Assist to supply additional hydraulic pressure when the vacuum boost is not sufficient to achieve the driver?s intended brake force. Dealers will reprogram the Electronic Brake Control Module in these vehicles with a new calibration that will improve how the system utilizes the Hydraulic Brake Boost Assist function when vacuum assist is depleted.

GDS 2.

severe internal engine damage.

that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.

This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact Partechand/orthe Techline Customer Support Center for additional support.

conductive finish.

the Tech 2 or GDS 2.

transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.

replace the pistons if found the cause of the oil consumption.

service or aftermarket calibrations.

Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.

P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range. Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2. Navigate to fuel system depressurize and at engine idle depressurize the fuel system. The fuel pressure sensor value should drop to 0 and the engine will stall. If a sensor is causing this concern the suspected sensor will not drop to 0 the engine will stall however the sensor will still read 30 to 40 pounds per square inch.

after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

how toptier fuels should be used to reduce carbon build up.

replace the pistons if found the cause of the oil consumption.

Diagnostic Trouble code P0300 set. There may be a rough running engine associated with this concern. If service information diagnostics have been completed and there is still no trouble found, the technician is to inspect for a possible terminal tension concern on the ignition coil power feed for the cause of the rough running engine and or the P0300. For the Service Engine Soon light or traction control lamp concern check the X2 connector of the under hood fuse block for poor pin retention.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.

This condidtion will occur within the first 5 minutes after the vehicle is started.his condition may be caused by a software anomaly that allows all four DTC's P0132, P0137, P0152, P0157 to set. All 4 DTCs must be in history for this PI to apply.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.

vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection.If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.

vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find Diagnostic Trouble Code P2537 and/or P129Dset. Technician will need to Use a voltmeter and check circuit 5985 at the Engine Control Module and Transmission Control Module. If no or low voltage is found, use the wiring diagram in Service Information and perform normal circuit diagnosis.

Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.

after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.

or the vehicle has sat for a few hours.

In some circumstances, some 2014-2017 model year Cadillac Escalade, Chevrolet Silverado, Chevrolet Suburban, Chevrolet Tahoe, GMC Sierra, and GMC Yukon vehicles may have a condition where customers may experience increased brake pedal effort, hard brake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applying the brakes. The engine mounted mechanical vacuum pump output may decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervals could contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5 minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs, the hydraulic brake system remains functional but may require additional pedal force. Please understand that even if the vehicle exhibits this condition, it meets all federal motor vehicle safety standards for brake performance. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.

Drive concern.

eliminate coolant smell and/or a slight leak at the radiator.

customers concern of engine misfire, ticking noise and/or MIL on.

Three or Four Cylinder Mode.

Engineers by completely filling out requested reports.

time.

replace the pistons if found the cause of the oil consumption.

intermittent pop noise from the speakers followed by a reset of the radio and clock. Technician will need to check for Diagnostic Trouble Codes and also check the battery for proper cable connections. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner’s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.

diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.

engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.

Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P2635, U0074 and or U18A2. Technician will need to follow published diagnostics for Diagnostic Trouble Codes U0074 would take priority over U18A2 if both set before addressing DTC P2635.

vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

Service Vehicles.

not pass California smog inspection or smog inspection in other states.

programs.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

Only).

programs.

before being sold (prepping) to the customer.

programs.

Only).

before being sold (prepping) to the customer.

Service Vehicles.

shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.

Only).

programs.

(WPC) Parts Return Program.

identification for warranty transactions (U.S. Only).

and Canada Dealers Only).

submit a Pre-Repair Authorization (PRA).

Dealer Special Tool Loan Program process.

operation.

replacements.

E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

services and maintenance on vehicles originating/sold in Canada.

replacements.

the warranty transaction submission procedures that support the Personal Property Damage process.

Only).

before being sold (prepping) to the customer.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

a fluid leak, and what is considered fluid seepage.

Assistance Center (TAC).

Only).

programs.

Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.

E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

(WPC) Parts Return Program.

Only).

and Canada Dealers Only).

Only).

Only).

submit a Pre-Repair Authorization (PRA).

submit a Pre-Repair Authorization (PRA).

warped or misshapen.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Dealer Special Tool Loan Program process.

Assistance Center (TAC).

Dealers Only).

Only).

Only).

Only).

vehicles before being sold (prepping) to the customer.

Spin-On Oil Filters.

Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

to GM for payment.

identification for warranty transactions (U.S. Only).

operation.

Only).

Dealers Only).

Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

the warranty transaction submission procedures that support the Personal Property Damage process.

Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

(WPC) Parts Return Program.

Only).

E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

and Canada.

Spin-On Oil Filters.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Only).

submit a Pre-Repair Authorization (PRA).

Only).

submit a Pre-Repair Authorization (PRA).

Only).

replacements.

warped or misshapen.

Spin-On Oil Filters.

(WPC) Parts Return Program Information.

Technical Assistance (TAC).

vehicles before being sold (prepping) to the customer.

Spin-On Oil Filters.

independent causes (GM Canada Dealers Only).

replacements.

replacements.

Spin-On Oil Filters.

Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

grille or radiator area.

operation.

Only).

programs.

programs.

Pre-Repair Authorization (PRA).

Pre-Repair Authorization (PRA).

Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

Dealers Only).

identification for warranty transactions (U.S. Only).

Only).

vehicles before sold (prepping) to the customer.

Pre-Repair Authorization (PRA).

warped or misshapen.

Only).

Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

Pre-Repair Authorization (PRA).

Only).

Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.

Pre-Repair Authorization (PRA).

Only).

(CCND) Labor Operation Numbers.

PF48.

information found in the service manual.

Only).

Pre-Repair Authorization (PRA) (US dealers only).

(WPC) Parts Return Program Information.

information found in the service manual.

(WPC) Parts Return Program Information.

Only).

information found in the service manual.

Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

(WPC) Parts Return Program Information.

programs.

(CCND) Labor Operation Numbers.

Only).

Only).

services and maintenance on vehicles originating/sold in Canada.

repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.

Pre-Repair Authorization (PRA) (US dealers only).

that may not pass California smog inspection or smog inspection in other states.

E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures.

Pre-Repair Authorization (PRA) (US dealers only).

information found in the service manual.

E4403, M4404, M4413, E4414, E4423, E4491 or E6961).

identification for warranty transactions (U.S. Only).

services and maintenance on vehicles originating/sold in Canada.

Enthusiasm.

vehicles before sold (prepping) to the customer.

Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.

50 terminal test probe, replacement terminals, and terminated leads.

50 terminal test probe, replacement terminals, and terminated leads.

50 terminal test probe, replacement terminals, and terminated leads.

system and replace the parts that may be contaminated due to oil in system.

system and replace the parts that may be contaminated due to oil in system.

technical assistance case using the dealer case management tool.

working on a LIN bus.

U**** Byte 71 DTC.

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

Allegation Resolution (PAR) claim.

Allegation Resolution (PAR) claim.

working on a LIN bus.

offered through GM.

working on a LIN bus.

U**** Byte 71 DTC.

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Allegation Resolution (PAR) claim.

offered through GM.

on 2015-2022 model year vehicles in the United States.

wear through, hole in second row (Intermediate) carpet.

working on a LIN bus.

offered through GM.

Allegation Resolution (PAR) claim.

Only)

the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component

do not return.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Allegation Resolution (PAR) claim.

Icon Selected on Menu.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

working on a LIN bus.

wear through, hole in second row (Intermediate) carpet.

higher CSi scores.

offered through GM.

interiors of GM vehicles.

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

interiors of GM vehicles.

Dealers Only).

front grille or radiator area.

Technical Assistance (TAC).

loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.

memory position.

normal operations.

Only).

verification sheets (CCVS).

for vehicles that may need an upgrade.

providing additional information on the AFM and DFM systems

working on a LIN bus.

U**** Byte 71 DTC.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

mismatch.

front grille or radiator area.

wear through, hole in second row (Intermediate) carpet.

Technical Assistance (TAC).

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

click type noise while driving.

wear through, hole in second row (Intermediate) carpet.

interiors of GM vehicles.

higher CSi scores.

Allegation Resolution (PAR) claim.

customer.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.

for certain repairs, such as Wiring Harness Repairs.

warranty replacements.

repairing wiring harnesses.

(U.S).

warranty replacements.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

warranty replacements.

warranty replacements.

repairing wiring harnesses.

warranty replacements.

Procedure as Outlined Below)

Procedure as Outlined Below)

Procedure as Outlined Below)

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

warranty replacements.

condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.

vehicle causing a wide varied of issues,depending on which wire(s) is chaffed.Repair the affected wiring as needed

front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.

replacements.

Loss of Steering Assist due to a software abnormality.

block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the main power buss bar has poor terminal tension.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.

replacements.

IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2 The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.

keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.

that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.

(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.

at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.

(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

replacements.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.

sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.

vehicle causing a wide varied of issues,depending on which wire(s) is chaffed.Repair the affected wiring as needed

front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole. There is a metal locking tab on the terminal that will need to be pushed in before the terminal will pull out of the connector.

click, tick, snap, or itch type noise in the steering column or steering wheel when turning left or right during low speeds or parking maneuvers. Technician will need to inspect for mis-routed airbag module wiring harness for contacting vibration damper plate in steering wheel, orreplace the column upper bearing inner race, spring, and seat.

applications.

applications.

at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.

inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.

Thisinformation advises dealers on how the seat functions and alsoa common area where an open circuit may be found between the third row seat module and the seat position sensor.It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well asadvising the dealer to look for bent/damaged seat recline mechanisms.

these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

hesitation when opening and closing the power liftgate. There may be a diagnostic trouble code B153A set in the power liftgate module. This concern could occur if the left liftgate actuator is internally coming apart. The actuator will need to be replaced however care must be taken when removing the actuator from the vehicle. If the internal portion of the actuator had completely separated the end of the actuator could become a projectile when removed. Obtain a number 8 self-tapping screw that measures 1 inches long. Fully open the liftgate and install the screw anywhere in a 30 millimeter space from the bottom of the smooth tube to secure the tubes. Continue with the liftgate actuator by following the liftgate power assist actuator procedure in service information.

Number in eSI and how to locate the part(s) in the EPC.

melted terminals on auxiliary relay, new auxiliary battery relay for Police Tahoe Vehicles.

these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.

Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.

that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.

sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.

when replacing a module.

block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the main power buss bar has poor terminal tension.

Sensing Cruise Control Module and provides tips for completing all necessary steps and to contact TCSC if configuration does not complete correctly.

programmedfob in the vicinity of the passive liftgate antenna. If the antenna can locate a programmed fob in saidarea, the gate will open if the liftgate open switch or hands free sensor is activated.

Wheel Drive" message on the Driver Information Center. Provides the technician with additional information to ensure that the TCCM contains the latest software released to address previous issues, also advises of default action changes. Calls out specific circuits to be inspected to help isolate intermittent codes.

replacements.

position reverse tilt position is inoperative.

transactions when doing wiring repairs.

replacements.

On certain passenger cars and light duty trucks, equipped with Gen 10 OnStar, the embedded phone flash memory chip may become corrupted, causing the OnStar system to become inoperative. Dealers are to replace and program the vehicle communication interface module (VCIM).

(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.

finish".

the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

due to seeing grease or sealant on certain locations on the gear.

engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.

t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by Rear of Transmission or Transfer Case Area.

the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

transmission leaking ATF causing the customers concern.

engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

due to seeing grease or sealant on certain locations on the gear.

test.

to shift the t-case from 4lo to Hi gears while driving.

setting up the pinion bearing pre-loads during reassembly of the 9.5/9.76 inch rear axles. Technician will need to use pinion gear install washer part number 11609638 onto the pinion shaft between the flange and nut. Tighten the pinion nut until you achieve 10 pound inch or 1.0 newton rotating torque. After the torque has been achieved back the nut off and remove the washer. Tighten the nut back down until you achieve 15 pound inch or 1.7 newton meters for used bearings or 20 pound inch 2.25 newton meters for new bearings.

and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

for metal.

for metal.

for metal.

software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

due to seeing grease or sealant on certain locations on the gear.

vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance

Some customers or technicians may comment on seeing grease or sealant on certain locations of the steering gear. The illustrations below include arrows showing the areas on the steering gear that the supplier intentionally applies sealing grease. Any of these locations have the potential of showing visible grease under normal operation.

for metal.

Shifts, Slips, or Flares.

for metal.

Shifts, Slips, or Flares.

Shifts, Slips, or Flares.

On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.

for metal.

after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

for metal.

software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.

On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.

for metal.

gear due to seeing grease or sealant on certain locations on the gear.

for metal.

customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.

transmissions.

Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.

addressing underbody component corrosion with customers.

have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

peeling, metal shows corrosion/rusting (U.S. and Canada Only).

shipping film.

Guidelines.

peeling, metal shows corrosion/rusting (U.S. and Canada Only).

characteristic.

Aluminum Wheels.

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

addressing underbody component corrosion with customers.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

Guidelines.

addressing underbody component corrosion with customers.

characteristic.

Replacement Guidelines.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

addressing underbody component corrosion with customers.

whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.

Replacement Guidelines.

percentage.

that it is considered a normal condition.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

front camera is loose or that the mirror/camera mounting bracket is loose or has fallen off. If a vehicle is encountered with the above condition, do not attempt to reinstall the bracket onto the windshield. The above listed vehicles have a revised bracket design that is not serviceable. It is necessary to replace the windshield glass assembly. The bracket comes installed on the new glass assembly. Refer to Windshield Replacement in SI.

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

characteristic.

Aluminum Wheels.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

addressing underbody component corrosion with customers.

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.

sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver?s door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time. As long as the driver?s door remains open the alarm will not turn back on and the new transmitters can be programmed.

have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).

Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

enabled.

Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.

eliminate a creak noise heard from the quarter lower rear trim panel area.

whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install foam tape along the entire length of the tail light assembly.

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

MIL and DTCs P0420 and P0430 setting.

Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.

strut due to fluid leak.

strut due to fluid leak.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

causing a voltage spike into the trucks electrical system which is causing DTC C1114 to set.

disk on gasket sealing surfaces or reused parts.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

disk on gasket sealing surfaces or reused parts.

disk on gasket sealing surfaces or reused parts.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

strut due to fluid leak.

from brakes, uneven front brake pad wear.

vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.

abrasive disk on gasket sealing surfaces or reused parts.

Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the driver and passenger sill plate to gain access to the wire harness. If any open, damaged, or corroded wires should be repaired.

from brakes, uneven front brake pad wear.

from brakes, uneven front brake pad wear.

repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within 2.0 mm (0.079 in) of the mounting plates. The rotors and pads should be replaced with the updated part number If the pads are out of specification, perform normal Service Information diagnostics to determine the cause of the concern.

vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer side connector are clean and securely fastened. If the vehicle?s 7-way connector socket terminals are deformed or have excessive wear, it will be necessary to replace the truck side connector with part number 23404450.

apply.

on gasket sealing surfaces or reused parts.

C1113 C1114 advising to address any battery issues first before any in depth diagnostics are done.

factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.

an OnStar In-Vehicle Voice Message Is Heard.

the rear speakers during the upfit of the vehicle.

being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message

Noise from the Speakers Followed by a Reset of the Radio and Clock due to a software issue.

Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.

SiriusXM Channels Due to Interference in Some Geographic Locations.

radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.

SiriusXM Channels Due to Interference in Some Geographic Locations.

analysis.

additive.

additive.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

additive.

the line is reinstalled correctly to avoid a no/low fuel pressure situation.

that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.

additive.

that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.

customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

additive.

diesel fuel.

Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.

Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

part and ordering it from the EPC.

rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.

in the fuel line.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

cranking condition.

Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

in the fuel line.

Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

along with several low speed lan DTCs.

Schedules.

Accessories.

Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

Fog/Driving Lamp Damage.

Accessories.

This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

Tires and PDI installed Limited Production Option (LPO) Tires.

This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

Coverage Period.

This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.

the Proper use of GM Simplified Maintenance Schedules.

Warranty Coverage Period.

Guidelines.

Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.

Vehicles.

repairs requiring balance and Road Force measurement.

Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

repairs requiring balance and Road Force measurement.

Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

ride characteristics of GM cars and trucks.

ride characteristics of GM cars and trucks.

Shake, Flat Spotting) of GM Original Equipment Tires.

GM Vehicles.

when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.

weather climates and testing those batteries.

Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.

Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.

Refrigerant Charge

and/or Insufficient Cooling due to the seals going bad within the part.

vehicles with the condition of rear defrosters inoperative or if one is to break during a normal repair.

and/or Insufficient Cooling due to the seals going bad within the part.

vehicles with the condition of rear defrosters inoperative or if one is to break during a normal repair.

Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.

Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.

vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

originating from the front of the vehicle that is more predominant during turns or traveling over bumps. This may be caused by a damaged stabilizer shaft frame bracket. There have been some cases in which the bracket is cracked, as shown. This condition has been found to be the result of insufficient welds between the bracket and frame rail. There have been some cases on older vehicles of corrosion affecting the bracket

click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.

vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.

vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.

considered a fluid leak, and what is considered fluid seepage.

considered a fluid leak, and what is considered fluid seepage.

considered a fluid leak, and what is considered fluid seepage.

considered a fluid leak, and what is considered fluid seepage.

Inspect the C-pillar which is the body verticalstructure behind the rear passenger doorarea of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.

Inspect the C-pillar which is the body verticalstructure behind the rear passenger doorarea of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.