2016 Chevrolet Impala TSBs
1,000 Technical Service Bulletins across 17 categories
Categories
Engine
330 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This informational bulletin advises the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
This bulletin updates the position of General Motors on refinishing aluminum wheels.
Read full bulletin
GM has determined that wheel refinishing under warranty will no longer be performed.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
Power Steering Cooling Lines and/or Engine Oil Cooler Line
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction...
Read full bulletin
Indicator Lamp (MIL) Illuminated.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
On some 2011-2015 model year Chevrolet Caprice and 2012-2016 model year Chevrolet Impala police patrol vehicles, idling...
Read full bulletin
the engine for extended periods of time can prematurely wear the engine-cooling-fan motor. In this condition, the motor may fail to operate or operate noisily. This condition can also damage motor-control relays in the underhood bussed electrical center (UBEC).
Engine Cooling Fan Motor
Power Steering Cooling Lines and/or Engine Oil Cooler Line
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This informational bulletin advised the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer...
Read full bulletin
concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides a procedure to replace the upper and lower valve body housings to correct customer...
Read full bulletin
concerns of launch shudder, 2-3 Upshift or 3-2 Downshift concerns.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint.
Read full bulletin
GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction...
Read full bulletin
Indicator Lamp (MIL) Illuminated?.
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine...
Read full bulletin
overheating, cooling system contaminated with engine oil.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine...
Read full bulletin
overheating, cooling system contaminated with engine oil.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. P0651 may also be set in the ECM with the P06DE. Technician must follow published Service Information diagnostics for P06DE. If diagnostics lead to removing the oil pan or engine oil pressure is below specification when hot, to inspect the oil piston nozzles for damage. Technician should replace the broken oil nozzle(s) as long as the engine does not have any damage which warrants engine replacement.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct launch...
Read full bulletin
shudder, 2-3 Upshift or 3-2 Downshift concerns.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct launch...
Read full bulletin
shudder, 2-3 Upshift or 3-2 Downshift concerns.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This preliminary informational (PI) provides diagnosis and repair information regarding bearing damage or when an engine...
Read full bulletin
will not rotate.
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC...
Read full bulletin
P0300 that may also be set.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vehicles that have hard start,...
Read full bulletin
extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately...
Read full bulletin
followingHFV6re-manufactured engines replacement.
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately...
Read full bulletin
followingHFV6re-manufactured engines replacement.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if...
Read full bulletin
faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct launch...
Read full bulletin
shudder, 2-3 Upshift or 3-2 Downshift concerns.
This technical bulletin provides a Service Procedure to correct a Condition of Ticking, Tap or Rattle Noise from Engine.
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a...
Read full bulletin
guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for...
Read full bulletin
customer concerns related to wheel alignment.
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as...
Read full bulletin
opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct the customer...
Read full bulletin
concern of launch shudder.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
N192210240 - Special Coverage Adjustment - Certain vehicles shown above, may have a condition that could cause the...
Read full bulletin
evaporative emissions purge valve to not fully close. If this condition occurs, the engine could run rough, hesitate or stall at idle speeds. Additionally, the Malfunction Indicator Light (Check Engine Light) would illuminate and a diagnostic trouble code would be set. This special coverage covers the condition described above for a period of 10 years or 150,000 miles (240,000 km) for Acadia, Cascada, Enclave, Traverse, vehicles or 10 years or 120,000 miles (193,000 km) for Caprice, Cruze, Encore, Impala, LaCrosse, Sonic and Trax vehicles, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to replace the evaporative emissions purge valve as necessary. The repairs will be made at no charge to the customer.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary information communicates the repair recommendations for misfire in HFV6re-manufactured engines.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after...
Read full bulletin
severe internal engine damage.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact Partechand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using...
Read full bulletin
the Tech 2 or GDS 2.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This Preliminary Information communication provides information on a rattle, tick, or knock type noise.
Read full bulletin
Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019model years.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary Information communication provides information to the technician about a customer?s request to remove...
Read full bulletin
or disable the Bi-Fuel Compressed Natural Gas system. General Motors does not condone the removal of the original equipped Compressed Natural Gas systems.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This informational bulletin provides information of a possible misfire that may happen from incorrect camshafts being...
Read full bulletin
installed in the reman engines.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin explains the normal characteristics of exhaust noise during active fuel management when in...
Read full bulletin
Three or Four Cylinder Mode.
This informational bulletin provides information for the dealer technician to gather as much information to help aid...
Read full bulletin
Engineers by completely filling out requested reports.
This informational bulletin provides information on a normal engine operating condition for faster emission warm up...
Read full bulletin
time.
This technical bulletin provides a procedure to replace the upper and lower valve body housings to correct the customer...
Read full bulletin
concern of launch shudder.
This Preliminary Information communication provides information to the technician about vehicles that will have an...
Read full bulletin
intermittent pop noise from the speakers followed by a reset of the radio and clock. Technician will need to check for Diagnostic Trouble Codes and also check the battery for proper cable connections. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information on a rattle, tick, or knock type noise.
Read full bulletin
Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017, 2018, and 2019model years.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This engineering informational bulletin is requesting information from the field on DTC B0074-0D set or stored in...
Read full bulletin
history and the air bag light on and/or intermittently on.
This engineering information PI is requesting information for pictures to be taken of cracked converter pipes.
This Bulletin Provides Information for Repairing Engine Front Cover Oil Leak, Sealing Surface Preparation and Applying...
Read full bulletin
RTV Sealant.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This engineering information PI ends the need for information from the field on vehicles that have the condition of...
Read full bulletin
Smoke or Burning Odor from Underhood with Malfunction Indicator Lamp Illuminated with DTC P305F or P058D.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician about the text messaging feature on...
Read full bulletin
some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle. However with iPhones text messages cannot be responded to when using the infotainment system, they can only be received. For android devices pair the phone to the system during the pairing process the phone will ask you to allow the vehicle to access the device contacts. A second question will pop up on the device asking to allow the vehicle to access the message access profile. Both have to be allowed for the text messaging feature to work.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary information communicates to the technician where to find the engine identification tag and what...
Read full bulletin
information on that tag to use during programming of someengine control modules.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016,...
Read full bulletin
P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module...
Read full bulletin
when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This preliminary informational bulletin provides repair information to correct a customer concern of vibration felt...
Read full bulletin
through the steering wheel, drivers and passengers seats or floor while vehicle in drive at idle.
This engineering information ends the need for information from the field on vehicles that have the condition of Service...
Read full bulletin
Air Bag Indicator Illuminated and DTC B0081 and/or B0074-0D Set.
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine...
Read full bulletin
Damage.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This preliminary informational bulletin provides repair information to correct a customer concern of vibration felt...
Read full bulletin
through the steering wheel, drivers and passengers seats or floor while vehicle in drive at idle.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This bulletin provides a procedure to replace the camshaft cover if the purge valve is full of contamination or oil.
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer...
Read full bulletin
concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This informational bulletin supplies infomation for identifying non-GM (Aftermarket) engine calibrations for gasoline...
Read full bulletin
engines using Tech 2 or GDS 2 (U.S. and Canada).
This engineering information bulletin ends the need for information from the field on vehicles that have the concern of...
Read full bulletin
a noisy water pump.
This bulletin provides a procedure to replace the crankshaft balancer if found the cause of the customers concerns of...
Read full bulletin
noises or sparks.
This technical bulletin provides a procedure to Complete the Circuit/System Verification steps to correct a condition of...
Read full bulletin
Malfunction Indicator Lamp (MIL) - Check Engine Light On, DTC P182E.
This engineering information bulletin is requesting information from the field on vehicles that have the concern of a...
Read full bulletin
noisy water pump.
This engineering information bulletin is ending the need for information on vehicles with the condition of a waterleak...
Read full bulletin
in the rear compartment.
This Preliminary Information communication provides information to the technician that when scanning a vehicle for...
Read full bulletin
Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Technician should not replace the Human Machine Interface for this concern, power cycling of the Human Machine Interface fuse should restore communication. Technician should be advised that the Human Machine Interface and Global Diagnostic System 2 interaction concern has been reported to engineering for root cause and correction.
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder.
Read full bulletin
A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016,...
Read full bulletin
P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative.
Read full bulletin
Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative.
Read full bulletin
Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
This Preliminary Information communication provides information to the technician about customers that may complain of...
Read full bulletin
various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
This Preliminary Information communication provides information to the technician that when scanning a vehicle for...
Read full bulletin
Diagnostic Trouble Codes, may find a temporary loss of Human Machine Interface communication with Global Diagnostic System 2. Technician should not replace the Human Machine Interface for this concern, power cycling of the Human Machine Interface fuse should restore communication. Technician should be advised that the Human Machine Interface and Global Diagnostic System 2 interaction concern has been reported to engineering for root cause and correction.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This engineering informational bulletin is requesting information from the field on vehicles that have the condition of ...
Read full bulletin
Smoke or Burning Odor from Underhood with Malfunction Indicator Lamp Illuminated with DTC P305F or P058D
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk...
Read full bulletin
on engine surfaces.
This informational bulletin provides information for engine oil life monitor operation calculation.
This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if...
Read full bulletin
faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC...
Read full bulletin
P0300 that may also be set.
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S.
Read full bulletin
and Canada
This bulletin provides a procedure to replace the camshaft cover if the purge valve is full of contamination or oil.
This Bulletin provides graphics, information and guidelines for engine component wear that require repair and not engine...
Read full bulletin
replacement.
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly...
Read full bulletin
replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This engineering information bulletin is requesting information from the field on vehicles that have the concern of a...
Read full bulletin
noisy water pump.
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine,...
Read full bulletin
transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
This informational bulletin provides information on the proper ways to remove or replace the key cylinder covers due to...
Read full bulletin
somevehicleshavingthe key cylinders hidden during the time of delivery.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary Information communication provides information on a rattle, tick, or knock type noise.
Read full bulletin
Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 and 2018 model year.
This Preliminary Information communication provides information to the technician about vehicles that have hard start,...
Read full bulletin
extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication advises the technician on the steps to diagnose the concern, and the steps to...
Read full bulletin
repair the concern of Diagnostic Trouble Code P228C setting. The technician is to inspect the fuel and readings for the High Pressure Fuel Pump. The technician is to drain and clean fuel tank and all lines if contamination is found. The technician is to replace the high pressure fuel pump and the fuel inlet line to the high pressure fuel pump. The dealer is to request the customer complete the fuel survey attached and send to the fuel system engineer at the e-mail address provided. Latest revision added model years to the PI with no other changes. New revision adds model year and removes the customer surveys.
This Preliminary Information communication provides information on a rattle, tick, or knock type noise.
Read full bulletin
Any drivability concerns they should be addressed prior to the following diagnostic progression. A sound file or video with sound of the noise needs to be made prior to dis-assembly to help isolate to one area in the engine. There are four different steps to diagnosis the concern. This communication was updated to include the 2017 and 2018 model year.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative.
Read full bulletin
Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
This Preliminary Information communication provides information to the technician to help determine if the vehicle is...
Read full bulletin
equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
This Preliminary Information communication provides information to the technician about vehicles with a spongy brake...
Read full bulletin
pedal after a hydraulic brake component was disconnected or replaced. The brake lines between the master cylinder and the antilock brake system module are routed higher than the master cylinder. If air enters the system it will travel to this high point if the system is opened for a repair. The technician will need to perform an automated bleed procedure using the scan tool to ensure all the air is purged out of the hydraulic system.
This Preliminary Information communication provides information to the technician about vehicles that have a random...
Read full bulletin
infotainment system resets while driving, screen temporarily goes blank and then returns after approximately 5 seconds, radio volume control inoperative, Heater-Vent-Air Conditioning controls function but will not show changes on the display, seek buttons on the front controls will not function, when using CarPlay the map is intermittently bright at night, front pedestrian icon "Check Box" disappears after changing selection, over-temp Pop-up displayed randomly, displays a quick blue screen when shifting to reverse, infotainment system resets when a device with a large amount of songs is connected, XM not showing Station List, and or Radio shows XM Station ID 0 intermittently. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
This Preliminary Information communication provides information to the technician about vehicles that the radio will not...
Read full bulletin
retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder.
Read full bulletin
A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This warranty administration bulletin provides retail, wholesale and fleet personnel with General Motors recommendations...
Read full bulletin
for customer concerns related to wheel alignment.
26180 Customer Satisfaction.
Read full bulletin
Certain vehicles, equipped with a remote trunk release (RPO AB5), may have an incorrect fuse value specified for fuse F66 (Trunk Release) on the Engine Compartment Fuse Block cover. Dealers will inspect, and if necessary, replace the fuse and/or fuse block cover.
17650 - Customer Advisory Letter.
Read full bulletin
If this condition affects your vehicle you may noticed the CNG odor or hear a hissing sound. To check for this condition, please have a certified CNG technician inspect the manual shut-off valve in accordance with GM Service Information procedures for CNG leakage and damage. This inspection should be performed regularly as part of the updated maintenance schedule. If the inspection is performed at a GM dealership, and your vehicle is still covered under its 5 year/50,000 mile (80,000 km) Emissions Control Systems Warranty, replacement of the manual shut-off valve, if required, will be performed for you at no charge. Additionally, we are updating the maintenance schedule in the CNG supplement to your owner manual to include regular inspection of the CNG manual shut-off valve. The insert is an amendment to your supplement. Please keep this insert with your important vehicle documents for reference.
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine...
Read full bulletin
damage.
26180 01 Customer Satisfaction Program.
Read full bulletin
Certain vehicles, equipped with a remote trunk release (RPO AB5), may have an incorrect fuse value specified for fuse F66 (Trunk Release) on the Engine Compartment Fuse Block cover. Dealers will inspect, and if necessary, replace the fuse and/or fuse block cover.
This Preliminary Information communication provides information to the technician about vehicles that the navigation...
Read full bulletin
system will be unable to enter addresses that contain diacritics using the touch screen. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative.
Read full bulletin
Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides the technician with the steps needed to diagnose and repair a...
Read full bulletin
vehicle with Wi-Fi or Bluetooth inoperative or poor performance concern. Technician will need to obtain data from Global Diagnostics Services 2 and call General Motors Technical Assistance Center for further assistance. Technician should be advised that concern only applies to OnStar Wi-Fi Regular Production Option Code (VV4) and Bluetooth Regular Production Option Code (UPF).
This Preliminary Information communication provides information to the technician about vehicles that have noise from...
Read full bulletin
the exhaust and / or exhaust odor within the vehicle. Technician may find the left hand catalytic converter pipe cracking near cylinder head mounting flange weld. Technician will need to replace the catalytic converter with latest part number from General Motors Service Parts Operations. General Motors is working on a solution for this concern.
This Preliminary Information communication provides information to the technician about vehicles that the radio will...
Read full bulletin
turn on unwanted after a key cycle when the radio was shut off before the key was turned off. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
This engineering informational bulletin is requesting information from the field on vehicles that exhibit the condition...
Read full bulletin
of rear turn signal bulb inoperative.
This informational bulletin provides information on the proper ways to remove or replace the key cylinder covers due to...
Read full bulletin
some vehicles having the key cylinders hidden during the time of delivery.
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and...
Read full bulletin
a list of websites for additional information.
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides...
Read full bulletin
information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B...
Read full bulletin
may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
This Preliminary Information communication provides information to the technician about vehicles that the radio will not...
Read full bulletin
retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
This Preliminary Information communication provides information to the technician about vehicles that have a knock...
Read full bulletin
noise, seized engine, lower end squeak or squeal from the engine. Technician will inspect the oil control solenoids for metal debris. Also inspect for damage to the cam caps Journals and camshaft journals on the heads. The check the timing chain idler sprockets for stiffness when turning. If any of these instances would be a cause to replace the engine instead of repair.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats.
Read full bulletin
Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
This technical bulletin provides a procedure to replace the sunroof window motor for vehicles with the condition of...
Read full bulletin
sunroof or sunshade inoperatice and DTC U151B
This Preliminary Information communication provides information to the technician about vehicles that have noise from the exhaust.
Read full bulletin
Technician may find the left hand catalytic converter pipe cracking near cylinder head mounting flange weld. Technician will need to replace the catalytic converter with latest part number from General Motors Service Parts Operations. General Motors is working on a solution for this concern.
This engineering informational bulletin ends the need for information from the field on vehicles that have the condition...
Read full bulletin
of Rear Stop/Turn Signal Bulb Inoperative.
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly...
Read full bulletin
replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
Pre-Delivery & Maintenance
186 bulletinsThis Preliminary information communicates direction to find information atwww.gmupfitter.comfor Police and Special...
Read full bulletin
Service Vehicles.
This service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may...
Read full bulletin
not pass California smog inspection or smog inspection in other states.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on proper use of floor mats.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This Preliminary information communicates direction to find information at www.gmupfitter.com for Police and Special...
Read full bulletin
Service Vehicles.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This service bulletin provides information on proper use of floor mats.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front...
Read full bulletin
grille or radiator area.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles...
Read full bulletin
that may not pass California smog inspection or smog inspection in other states.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398,...
Read full bulletin
E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This Preliminary information communicates to the technician information on what may be setting DTC P06DE.
Read full bulletin
This is in addition to what is already in the service manual.
This Preliminary information communicates to the technician information on what may be setting DTC P06DE.
Read full bulletin
This is in addition to what is already in the service manual.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer...
Read full bulletin
Enthusiasm.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This warranty administration bulletin provides policy information on required operating procedures.
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S.
Read full bulletin
and Canada dealers only.
This warranty administration bulletin provide policy information on required operating procedures.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is...
Read full bulletin
considered warranty and non-warranty.
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
This informational bulletin provides information retaining to the fact that Service Manuals will now be available on...
Read full bulletin
USB.
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information on required operating procedures.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI)...
Read full bulletin
process and to encourage delivering quality vehicles and generating higher CSi scores.
This warranty administration bulletin provides policy information with the field action courtesy transportation policy.
This warranty administration bulletin provide policy information on the change in product field action customer...
Read full bulletin
reimbursement procedure.
This warranty administration bulletin provide policy information on required operating procedures.
This bulletin provides information on approved warranty part numbers for original equipment batteries.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer...
Read full bulletin
Enthusiasm.
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the...
Read full bulletin
warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty administration bulletin provide policy information on required operating procedures.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential...
Read full bulletin
tools that include consumable parts (U.S. Only).
This warranty administration bulletin provides information on GM?s policy on performing GM covered vehicle services and...
Read full bulletin
maintenance on vehicles originating/sold in Canada.
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provide policy information on required operating procedures.
This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy...
Read full bulletin
Guidelines.
This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the...
Read full bulletin
warranty transaction submission procedures that support the Personal Property Damage process.
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S.
Read full bulletin
and Canada dealers only.
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
Other
128 bulletinsThis preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
New Vehicle Monitoring Programs Section in IVH
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM...
Read full bulletin
technical assistance case using the dealer case management tool.
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
No Reverse, No Third, DTC P0716, P0717
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and...
Read full bulletin
verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
Changing Turn-By-Turn Voice Response To Metric Or English Units
No Reverse, No Third, DTC P0716, P0717
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and...
Read full bulletin
verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Preliminary information communicates a process to correct theconcern of Unable to contact OnStar after the 3G EOL...
Read full bulletin
on 2015-2022 model year vehicles in the United States.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
IPC Odometer Programming Method Quick Reference Guide
This informational bulletin provides information on proper use of floor mats.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Essential Tools that Include Consumable Parts (U.S.
Read full bulletin
Only)
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify...
Read full bulletin
the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
IPC Odometer Programming Method Quick Reference Guide
All or Some Options May Be Missing from Driver Information Center (DIC) Info Pages Menu Due to Them Not Being Selected ...
Read full bulletin
Condition Some customers may comment that with the Info option selected from the main menu (1), the Info Pages are blank (2) when scrolling up and down. If information is present when scrolling up and down, they may also comment that certain items are missing when compared to other like vehicles Cause This condition may be caused when all/some of the options not being selected in the active info pages menu. Correction If this concern is encountered, determine if all/any of the selections in the active info pages menu are not selected. To do this, follow the steps listed below.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this...
Read full bulletin
should be considered a normal characteristic.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary Information communication provides the technician with information on the proper washing of the bright...
Read full bulletin
aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This Preliminary information communicates a diagnostic trail to a likely conclusion for lean codes on these vehicles.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin explains the importance of maintaining the vehicle.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the...
Read full bulletin
customer.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles.
Read full bulletin
A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
This Preliminary information communicates
This Preliminary information communicates additional diagnostics to assist the dealer technician with diagnosing and...
Read full bulletin
repairing trouble code P2097.
This Preliminary Information communication provides the technician with information on the proper washing of the bright...
Read full bulletin
aluminum moldings to avoid the moldings from getting damaged. It is recommended that a non-alkaline solution be used for preparation & washing of the bright aluminum moldings.
This preliminary information communicates the steps needed to add keys to a fleet vehicle.
This Preliminary Information communication provides information to the technician about connectivity concerns when...
Read full bulletin
connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This Bulletin provides a procedure to activate/enable 4G LTE Wi-Fi Hotspot on New vehicle.
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital...
Read full bulletin
pictures.
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the...
Read full bulletin
part numbers for the labels.
This informational bulletin provides a diagnostic tip for rear vision camera image that is grainy, distorted and/or...
Read full bulletin
pixelated
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This technical bulletin provides a procedure to install a clip on the head rest j-clip to correct a condition of the...
Read full bulletin
head rest material coming loose due to the j-clip not being robust enough to retain the material down.
This bulletin describes the Dealer special tool loan program process.
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer...
Read full bulletin
inventory.
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This technical bulletin provides repair information to correct a customer concern of the heated seat back inoperative...
Read full bulletin
when pressing the seat back only switch.
This technical bulletin provides a procedure to install a clip on the head rest j-clip to correct a condition of the...
Read full bulletin
head rest material coming loose due to the j-clip not being robust enough to retain the material down.
This informational bulletin explains the Road Force balancers and what they can do for customer concerns.
This informational bulletin explains the difference in oil filters and the possibilities of what may happen using the...
Read full bulletin
incorrect filter.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance...
Read full bulletin
Claim (PAC) within the Courtesy Transportation Assistance Program.
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known...
Read full bulletin
as a Product Allegation Resolution (PAR) claim.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in...
Read full bulletin
vehicles.
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended...
Read full bulletin
Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of...
Read full bulletin
torque specifications.
This technical bulletin provides repair information to correct a customer concern the CNG fill receptacle dust cap tether is prematurely wearing.
Read full bulletin
The premature wear can be described as being cracked, weather checked or broken.
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications...
Read full bulletin
to Control GM Accessory Remote Start Kits.
This technical bulletin provides repair information to correct a customer concern of the driver and/or passenger power...
Read full bulletin
seat height stuck in the full-up position, intermittent inoperative seat adjustment or not lowering.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative.
Read full bulletin
Technician will need to toggle through all languages then back to the desired language.
This Preliminary information communicates a diagnostic trail to a likely conclusion for lean codes on these vehicles.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity.
Read full bulletin
Technician should check the Regular Production Option Code list for (VV4).
This technical bulletin provides repair information to correct a customer concern of the driver and/or passenger power...
Read full bulletin
seat height stuck in the full-up position, intermittent inoperative seat adjustment or not lowering.
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to...
Read full bulletin
contact PQC prior to replacing an assembly (U.S. and Canada only).
This bulletin provides a procedure to adding new brackets and repairing the front seats to correct the seats excessive...
Read full bulletin
movements.
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key...
Read full bulletin
Fob or OnStar Mobile Application and where to locate the information for future use.
This informational bulletin explains the Road Force balancers and what they can do for customer concerns.
This Preliminary information communicates additional diagnostics to assist the dealer technician with diagnosing and...
Read full bulletin
repairing trouble code P2097.
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles.
Read full bulletin
A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin provides information on a new U.S.
Read full bulletin
dealer special tool loan program.
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to...
Read full bulletin
properly disable the SIR system for repairs at or near
This informational bulletin provides information on Clarification of Use - Dealer Empowerment Labor Operations and Customer Enthusiasm (U.S.
Read full bulletin
Only)
This preliminary informational bulletin provides Diagnostic Tips for Stop/Start and AutoStop Operation on vehicles that...
Read full bulletin
have a conditon of AutoStop mode not engaging and vehicle automaticlly restarts during a autostop event
This informational bulletin provides information on Installing the Correct Replacement Spin-On Oil Filter When...
Read full bulletin
Servicing.
This informational bulletin explains not to put anything metal or conductive on the passenger seat or it may set the...
Read full bulletin
reminder chime off.
This informational bulletin provides information for dealers how to submit a product information report.
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this...
Read full bulletin
should be considered a normal characteristic.
This informational bulletin provides information for dealers/technicians on when and how to submit a field product...
Read full bulletin
report.
Electrical
92 bulletinsThis Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use...
Read full bulletin
for certain repairs, such as Wiring Harness Repairs.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Ambient Temperature Sensor Reads High on HVAC Data Lists.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This service bulletin provides information on Module Harvesting.
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a...
Read full bulletin
condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
This Preliminary information communicates that the coolant temperature sensor may leak coolant and wick into the ECM...
Read full bulletin
connector possibly causing a Hood Ajar message, CEL and a P257D.
Service Update. On some vehicles the evaporator core may leak due to condensate collecting and freezing between the lower tanks.
Read full bulletin
Dealers should reprogram the HVAC System Control Module to control evaporator icing.
Service Update. On some vehicles the evaporator core may leak due to condensate collecting and freezing between the lower tanks.
Read full bulletin
Dealers should reprogram the HVAC System Control Module to control evaporator icing.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1.
Read full bulletin
IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2 The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern.
Read full bulletin
The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. If the test fails the technician is instructed to replace the sensor and then perform the sweep test again. If the test passes the technician is instructed to reinstall the fuel module in the tank and if the test fails with the new sensor the technician is advised to replace the fuel module.
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct...
Read full bulletin
battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple...
Read full bulletin
keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple...
Read full bulletin
keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin explains to the technician that when using wiring repair labor operations,...
Read full bulletin
additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
Special Coverage. Some vehicles may have a condition where the electrical wires leading to the passenger presence...
Read full bulletin
sensing mat in the passenger?s front seat, may become disconnected over time, as a result of repeated seat usage. If this condition occurs, regardless of whether the front passenger seat is occupied, multiple airbag warnings will be provided. A Service Airbag message will be provided in the Driver Information Center (DIC), the airbag warning light will be illuminated, and the front passenger airbag will indicate that it is OFF. When this condition occurs, the front passenger airbag may be suppressed and fail to deploy when commanded.Dealers are to replace the PPS sensor. The repairs will be made at no charge to the customer.
This informational bulletin provides information on key code security rules and information on GM keycode look-up...
Read full bulletin
applications.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part...
Read full bulletin
Number in eSI and how to locate the part(s) in the EPC.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This technical bulletin provides a procedure on how to diagnosis a possible resistance concern in the battery system.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This informational bulletin provides information for programming the low speed LAN module due to the mirrors memory...
Read full bulletin
position reverse tilt position is inoperative.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive...
Read full bulletin
finish".
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.
This technical bulletin provides a procedure to check the X2 or PPS sensor mat terminal connector for loose connections...
Read full bulletin
that may cause the airbag warning message to come on.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This technical bulletin provides a procedure to check the X2 or PPS sensor mat terminal connector for loose connections...
Read full bulletin
that may cause the airbag warning message to come on.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about the Media Oriented Systems...
Read full bulletin
Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern.
Read full bulletin
The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. If the test fails the technician is instructed to replace the sensor and then perform the sweep test again. If the test passes the technician is instructed to reinstall the fuel module in the tank and if the test fails with the new sensor the technician is advised to replace the fuel module.
This Preliminary information communicates to the dealer an issue where the vehicle's inspection and maintenance monitors...
Read full bulletin
along with diagnostic trouble codesmay reset unprompted due to the installation of an aftermarket fuel pump control module.
This PI offers diagnostic tips to a technician when diagnosing a possible fuel level sensor concern.
Read full bulletin
The tech is advised to ohm test the sensor at the terminals located on top of the fuel module while performing a sweep test. If the test fails the technician is instructed to replace the sensor and then perform the sweep test again. If the test passes the technician is instructed to reinstall the fuel module in the tank and if the test fails with the new sensor the technician is advised to replace the fuel module.
This Preliminary Information communication provides information to the technician on how to tell the difference between...
Read full bulletin
the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
This technical bulletin provides a procedure to repair and reposition the seat pretentioner wiring harness away from...
Read full bulletin
the seat frame to correct a possible short when the seat is in the full down position.
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio...
Read full bulletin
with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU are not the cause.
This technical bulletin provides a procedure to check the X2 or PPS sensor mat terminal connector for loose connections...
Read full bulletin
that may cause the airbag warning message to come on.
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display,...
Read full bulletin
due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module.
This informational bulletin provides information on Wireless Charging Module Diagnosis and cell phone compatibility.
This warranty administration bulletin provides policy information on ACDelco replacement battery warranty procedures.
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code...
Read full bulletin
E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
This technical bulletin is providing a procedure to reprogram the HMI module to correct multiple conditions including...
Read full bulletin
Waiting for Update Media Message, Voice Command For Calling Bluetooth Phone Contacts Inoperative, Intermittent Loss of Rear Camera Gridlines, Service Rear Vision System Message, Radio Turns On Unwanted At Startup, and/or Navigation Radio Destination State Defaults To WV, Intermittent Radio/display Resets, Volume Control Inoperative.
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and...
Read full bulletin
reprogram modules.
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313...
Read full bulletin
Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
This technical bulletin provides a procedure to replace the side object detection wiring and harness if inspection finds...
Read full bulletin
water and/or corrosion in the harness or modules.
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED,...
Read full bulletin
No WiFi Operation, and/or Limited OnStar Module Functionality After OnStar Module Replacement for Another Condition.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This informational bulletin provides information to dealership personnel regarding original equipment battery part...
Read full bulletin
numbers and AC Delco replacement battery approved warranty part numbers.
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel...
Read full bulletin
revised wiring repair labor operations and required additional information.
This technical bulletin provides multiple fixes for a condition of a waiting for update screen appearing on the display,...
Read full bulletin
due to either a reprogramming of the hmi module or due to a fuse that needs to be pulled and restarting of the module.
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers
The information in this bulletin details the proper configurations for the ignition key, fob, key tags and key rings and...
Read full bulletin
applying a QR code sticker or barcode sticker to a key fob.
Battery Testing and Warranty Replacement Requirements (North America ONLY)
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
The information in this bulletin details the proper configurations for the ignition key, fob, key tags, key rings, key...
Read full bulletin
ring sizes and applying a QR code sticker or barcode sticker to a key fob.
This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse...
Read full bulletin
replacement.
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up.
Read full bulletin
Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
This informational bulletin provides information to dealership personnel on the use of non-GM approved battery chargers...
Read full bulletin
and booster packs.
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a...
Read full bulletin
long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to...
Read full bulletin
reprogram modules that have been already reprogrammed.
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
This Preliminary Information communication a diagnostic tip if the high speed lan bus is shorted to ground, which can...
Read full bulletin
cause the BCM to appear off line.
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required...
Read full bulletin
additional information.
This technical bulletin provides a procedure to locate a possible electrical connector if the STS message comes on.
This technical bulletin provides a procedure to inspect and repair the front seats wiring harness only if certain SIR...
Read full bulletin
DTCs are set.
Body & Paint
53 bulletinsThis preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the...
Read full bulletin
shipping film.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides information on Paintless Dent Repair Process.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
Information on Inside Rear view Mirror and Camera Loose
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint...
Read full bulletin
percentage.
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and...
Read full bulletin
that it is considered a normal condition.
Information on Inside Rear View Mirror and Camera Loose Some customers may comment that the inside rear view mirror or...
Read full bulletin
front camera is loose or that the mirror/camera mounting bracket is loose or has fallen off. If a vehicle is encountered with the above condition, do not attempt to reinstall the bracket onto the windshield. The above listed vehicles have a revised bracket design that is not serviceable. It is necessary to replace the windshield glass assembly. The bracket comes installed on the new glass assembly. Refer to Windshield Replacement in SI.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This preliminary bulletin provides a procedure to replace the sunroof sunshade if it binds or doesn't retract properly.
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of...
Read full bulletin
mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse of the affected side. The front wheel house flange may have a void in the sealer causing water to leak through and accumulate on the floor or wet carpet will be found. A thumb grade sealer will need to be placed in the void to prevent the water leak into the cabin.
This Preliminary Information communication provides information to the technician about vehicles that have a ticking...
Read full bulletin
noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the...
Read full bulletin
shipping film.
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving...
Read full bulletin
Speeds
This informational bulletin provides information for assisting the customer in setting the position for the memory...
Read full bulletin
mirror and the reverse tilt
This informational bulletin provides recommendations and product information for application of anti-corrosion materials
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of...
Read full bulletin
Chromed Aluminum Wheels.
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal...
Read full bulletin
characteristic.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This preliminary informational bulletin provides windshield replacement information to correct a customer concern that...
Read full bulletin
the inside rear view mirror is loose or that the mirror mounting bracket is loose or has fallen off.
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of...
Read full bulletin
mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse of the affected side. The front wheel house flange may have a void in the sealer causing water to leak through and accumulate on the floor or wet carpet will be found. A thumb grade sealer will need to be placed in the void to prevent the water leak into the cabin.
This Technical Bulletin provides a procedure to add a nut correcting the gap of the upper trim cover to the IP.
This technical bulletin provides a procedure to replace the horn due to water intrusion causing a weak, not clear,...
Read full bulletin
abnormal and/or is inoperative.
This Preliminary Information communication provides the technician with the steps to diagnose and repair the concern of...
Read full bulletin
mildew odor or water on front floor on either side of the vehicle. Technician will gain access to the front wheelhouse of the affected side. The front wheel house flange may have a void in the sealer causing water to leak through and accumulate on the floor or wet carpet will be found. A thumb grade sealer will need to be placed in the void to prevent the water leak into the cabin.
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the...
Read full bulletin
flanges when the repairs are done.
This Preliminary Information communication provides information to the technician about vehicles that have a ticking...
Read full bulletin
noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
This informational bulletin provides information on how to properly repair rust on the hem flange on doors for vehicles...
Read full bulletin
that have the condition of rust showing at hem flange
This technical bulletin provides a procedure to replace the garage door opener transmitter to correct a condition of...
Read full bulletin
poor range for the garage door opener.
Fuel System
45 bulletinsThis informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for...
Read full bulletin
analysis.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable...
Read full bulletin
diesel fuel.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
Special Coverage. On some vehicles, the evaporator core may become damaged as a result of repeated freeze/thaw cycles...
Read full bulletin
without proper drainage of the condensate from the core. A damaged evaporator core may leak refrigerant and result in a loss of air conditioning function. Dealers are to confirm the air conditioning system evaporator core is the source of the refrigerant leak, and replace the core if its sealing is compromised. The repairs will be made at no charge to the customer.
Special Coverage. On some vehicles, the evaporator core may become damaged as a result of repeated freeze/thaw cycles...
Read full bulletin
without proper drainage of the condensate from the core. A damaged evaporator core may leak refrigerant and result in a loss of air conditioning function. Dealers are to confirm the air conditioning system evaporator core is the source of the refrigerant leak, and replace the core if its sealing is compromised. The repairs will be made at no charge to the customer.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
Exhaust Smell and/or Leak with Possible Malfunction Indicator Lamp Illuminated Condition Some customers may comment...
Read full bulletin
on an exhaust smell and/or leak with possible malfunction indicator lamp illuminated. During diagnosis, a technician may find DTC P0430 and/or P0420. Cause This may be due to a crack around the catalytic mounting flange. Correction Replace converter assembly with new service part.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary information communicates that a dealer may receive a replacement AC evaporator with TXV tubes that are bent.
Read full bulletin
The dealer is instructed on how to inspect for bent tubes. The dealer is advised if the evaporator TXV tubes are bent that they should not attempt to adjust the tubes but instead should replace the evaporator again.
This Preliminary information communicates that a dealer may receive a replacement AC evaporator with TXV tubes that are bent.
Read full bulletin
The dealer is instructed on how to inspect for bent tubes. The dealer is advised if the evaporator TXV tubes are bent that they should not attempt to adjust the tubes but instead should replace the evaporator again.
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the...
Read full bulletin
part and ordering it from the EPC.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This Preliminary information communicates that a dealer may receive a replacement AC evaporator with TXV tubes that are bent.
Read full bulletin
The dealer is instructed on how to inspect for bent tubes. The dealer is advised if the evaporator TXV tubes are bent that they should not attempt to adjust the tubes but instead should replace the evaporator again.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This technical bulletin provides a procedure to replace the catalytic converters due to cracks that may cause a noise or...
Read full bulletin
exhaust smell within the cabin.
This Preliminary information communicates that a dealer may receive a replacement AC evaporator with TXV tubes that are bent.
Read full bulletin
The dealer is instructed on how to inspect for bent tubes. The dealer is advised if the evaporator TXV tubes are bent that they should not attempt to adjust the tubes but instead should replace the evaporator again.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
N182186881 01 - Special Coverage Adjustment.
Read full bulletin
On some vehicles, the evaporator core may become damaged as a result of repeated freeze/thaw cycles without proper drainage of the condensate from the core. A damaged evaporator core may leak refrigerant and result in a loss of air conditioning function. Dealers are to confirm the air conditioning system evaporator core is the source of the refrigerant leak, and replace the core if its sealing is compromised. The repairs will be made at no charge to the customer.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks...
Read full bulletin
using the evaporative emission cart smoke machine and ultrasonic leak detectortools.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if...
Read full bulletin
debris have entered the exhaust system.
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER...
Read full bulletin
Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
This technical bulletin provides a procedure to replace the catalytic converters due to cracks that may cause a noise or...
Read full bulletin
exhaust smell within the cabin.
This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This preliminary informational bulletin adds the 2015 and 2016 model years to information regarding the normal...
Read full bulletin
characteristic of the exhaust system on a brief rattle or noise heard from the front or the rear of the vehicle on a cold start up.
Transmission
35 bulletinsThe service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin informs the technician of an alternate lift procedure that has been developed when the lift plate...
Read full bulletin
does not fit the top of the transmission case for 6T30, 6T35, 6T40, 6T45, and 6T50 Transmissions.
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
Information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares
Information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
Information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This informational bulletin provides normal operating characteristics and diagnostic information on Manual...
Read full bulletin
transmissions.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This informational bulletin provides technicians with information to assist in identifying operating characteristics of...
Read full bulletin
manual transmissions that repair attempts will not change.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
Lighting
33 bulletinsThis informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary information communicates to dealers of a known issue with failed map update
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
SHAKE AND/OR SHUDDER DURING LIGHT THROTTLE ACCELERATION BETWEEN 40 AND 128 KM/H (25 AND 80 MPH) AT A STEADY STATE.
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and...
Read full bulletin
the Proper use of GM Simplified Maintenance Schedules.
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During...
Read full bulletin
Warranty Coverage Period.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This Preliminary information communicates additional diagnosticsand repairto assist in resolving a malfunction indicator...
Read full bulletin
lampillumination due to any combination of diagnostic trouble codes P0068 P0101 P0106 P0171 P0131 P0137 P0324 P0326 P0331 P0506.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be...
Read full bulletin
covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including...
Read full bulletin
flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary information communicates additional diagnosticsand repairto assist in resolving a malfunction indicator...
Read full bulletin
lampillumination due to any combination of diagnostic trouble codes P0068 P0101 P0106 P0171 P0131 P0137 P0324 P0326 P0331 P0506.
This Preliminary Information communication provides information to the technician about vehicles that may have a clock...
Read full bulletin
that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
16099 Service Update.
Read full bulletin
Certain vehicles may have a condition in which the Impala driver side stop lamp bulb and Enclave passenger stop lamp bulb could burn out earlier than expected. Dealers will replace the bulb.
This Preliminary Information communication provides information to the technician about vehicle's odometer appears...
Read full bulletin
to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
This Preliminary information communicates additional diagnosticsand repairto assist in resolving a malfunction indicator...
Read full bulletin
lampillumination due to any combination of diagnostic trouble codes P0068 P0101 P0106 P0171 P0131 P0137 P0324 P0326 P0331 P0506.
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system.
Read full bulletin
For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and...
Read full bulletin
what should be considered warranty replacement and not
This informational bulletin provides information on Unscheduled Supplemental Services (Including Flushing Services and...
Read full bulletin
Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only)
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
Infotainment
28 bulletinsRadio Inoperative with No Communication and DTC U0184
Infotainment System Will Not Return to Media After Bluetooth Call Ends
This informational bulletin provides information on Normal Radio Display Operation ? Display Does Not Remain Off at...
Read full bulletin
Times After Being Turned Off in Settings and no parts should be replaced due to this condition.
This technical bulletin provides a procedure to correct a condition of a Side Detection Message Being Displayed on DIC.
This technical bulletin provides a procedure to replace the radio for vehicles with the condition of Intermittent Pop...
Read full bulletin
Noise from the Speakers Followed by a Reset of the Radio and Clock due to a software issue.
This Technical Bulletin provides procedures to upgrade a vehicle with the Android Auto feature for 2016 and 2017 Model...
Read full bulletin
Year vehicles.
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some...
Read full bulletin
SiriusXM Channels Due to Interference in Some Geographic Locations.
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some...
Read full bulletin
SiriusXM Channels Due to Interference in Some Geographic Locations.
This Preliminary Information communication provides information to the technician about vehicles that may have an issue...
Read full bulletin
when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
This informational bulletin provides information and Tips for Customers Having Difficulty Launching Android Auto or...
Read full bulletin
Apple CarPlay.
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not...
Read full bulletin
function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
This informational bulletin provides information for the technician when looking up the P/N for the 3.5 mm audio jack...
Read full bulletin
for the USB, to make sure and enter the VIN# to ensure the correct part is being ordered.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a...
Read full bulletin
condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
Side Detection System Message Being Displayed on Driver Information Center - DTC B101E-43 Set
This Technical Bulletin provides a fix to reprogram the radio for vehicles that may experience any of the following...
Read full bulletin
conditions: DTC U0184 Set, Radio Inoperative, Blue Screen, AM Clipping Noise, HD On/Off Status Not Retained in Stations, Time Lag on Transitions, No Audio with Internal Amp, Park Assist Symbol Position Wrong in Rear View Camera
This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a...
Read full bulletin
normal characteristic.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a...
Read full bulletin
condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc...
Read full bulletin
information.
This informational bulletin provides information to the customer on the radio display "info pages" being blank and to...
Read full bulletin
make sure to select in the "active info pages" menu.
This technical bulletin provides a procedure to reprogram the radio to correct a customer concern of radio Inoperative,...
Read full bulletin
blue Screen, AM clipping noise, HD on/off status not retained in stations, time lag on transitions, no audio with internal amp, and park assist symbol position wrong in rear view camera.
This Preliminary Information communication provides information to the technician about a connectivity concern with...
Read full bulletin
Bluetooth after phone software is updated or after any vehicle updates for the radio or Human Machine Interface has taken place. Technician should delete all Bluetooth pairings and then reboot the Bluetooth device and the vehicle. After the vehicle and radio is booted back up repair the Bluetooth device.
This Preliminary Information communication provides information to the technician about vehicles voice recognition...
Read full bulletin
inoperative for calling Bluetooth phone contacts. Technician will need to Clear All Private Data and repair any phones that were deleted.
This technical bulletin provides a procedure to reprogram the radio to correct a customer concern of radio Inoperative,...
Read full bulletin
blue Screen, AM clipping noise, HD on/off status not retained in stations, time lag on transitions, no audio with internal amp, park assist symbol position wrong in rear view camera.
This informational bulletin provides information on GM offering the Android Auto feature upgrade for 2016 and 2017 model...
Read full bulletin
year vehicles and how to proceed with reprogramming the vehicles to include this application for use.
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation...
Read full bulletin
Discs .
This informational bulletin provides Information on Inappropriate Warranty Claims Submitted for Damaged Radios and...
Read full bulletin
Instrument Panel Clusters (IPCs)
This technical bulletin provides a procedure on how to remove door trim panles and replace chime speaker pigtail...
Read full bulletin
connectors for vehicles with the condition of intermittent loss of chime from speaker
Brakes
21 bulletinsThis service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin informs dealers that a new Power Brake Booster Vacuum Cap will need to be replaced when installing...
Read full bulletin
the revised Power Brake Booster Vacuum Pipe to correct DTCs being set due to misrouting of brake booster vacuum pipe.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin informs dealers that a new Power Brake Booster Vacuum Cap will need to be replaced when installing...
Read full bulletin
the revised Power Brake Booster Vacuum Pipe to correct DTCs being set due to misrouting of brake booster vacuum pipe.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin informs dealers that a new Power Brake Booster Vacuum Cap will need to be replaced when installing...
Read full bulletin
the revised Power Brake Booster Vacuum Pipe to correct DTCs being set due to misrouting of brake booster vacuum pipe.
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly...
Read full bulletin
abrasive disk on gasket sealing surfaces or reused parts.
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk...
Read full bulletin
on gasket sealing surfaces or reused parts.
This technical bulletin provides a procedure for installing fan guards on both driver and passenger seat cooling fans...
Read full bulletin
due to the ventilation fans coming into contact with the seat cushion pad causing a noise when in use.
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red...
Read full bulletin
brake light intermittently comes on.
This informational bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This Preliminary Information communication provides information to the technician about a rattle coming from the rear of...
Read full bulletin
the vehicle when driving over medium sized bumps, it may sound like a loose spare tire or suspension component. The noise is most likely the left and right retaining clips holding the midsections of the parking brake cables to the car. The rattle can be repaired by preloading the cables using the published parking brake adjustment procedure found in service information.
This preliminary informational bulletin adds the 2014 - 2016 model years to cleaning information to correct a customer...
Read full bulletin
concern of seeing a white film/residue on the IP pad and/or door trim panels.
This informational bulletin provides information on installing the correct tires for vehicles with the condition of...
Read full bulletin
under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
This technical bulletin provides a procedure for repairing a customer concern of a mis-alignment of the IP top trim pad...
Read full bulletin
to the navigation screen upper trim cover.
This bulletin provides information on how to properly clean wheel speed sensors and wheel bearings that may cause...
Read full bulletin
conditions of EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message -Click Or Ratchet Noise- Service Traction Message - Service Stabilitrak Message - Service Steering Message due to dirt and debris.
Tires & Wheels
20 bulletinsThis service bulletin provides information on Tire Sidewall Irregularities.
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM...
Read full bulletin
Vehicles.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance,...
Read full bulletin
Shake, Flat Spotting) of GM Original Equipment Tires.
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for...
Read full bulletin
GM Vehicles.
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force...
Read full bulletin
Variations and the difference between balancing a flange and flangeless rim.
This informational bulletin provides information on the temporary tire flat spotting condition.
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and...
Read full bulletin
balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
This Informational bulletin outlines the recommendations for aluminum and chrome wheel refinishing.
HVAC & Climate
8 bulletinsThis service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold...
Read full bulletin
weather climates and testing those batteries.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS)...
Read full bulletin
concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
This technical bulletin provides repair information for the correction of a customer concern of short duration musty...
Read full bulletin
odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor...
Read full bulletin
emanating from HVAC system.
Software & Calibration
7 bulletinsThis service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This informational bulletin provides technicians with updated information to help identify the differences between what...
Read full bulletin
is considered a fluid leak, and what is considered seepage.
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for...
Read full bulletin
electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
This warranty administration bulletin provides policy information on an updated warranty and policy exchange program for...
Read full bulletin
electronic products through GM authorized Electronic Service Centers (ESCs) (U.S. and Canada).
Hybrid & EV
5 bulletinsThis service bulletin provides information on AGM batteries that require less frequent charging in storage.
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
This Preliminary Information communication provides information to the technician about vehicles that have cold air...
Read full bulletin
blowing from the center console or cold air blowing from the wireless charging mat area. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This technical bulletin provides a procedure to replace the GEN I charging system with a GEN II charging system only if...
Read full bulletin
vehicles apply within the settings.
This Preliminary Information communication provides information to the technician about vehicles that have cold air...
Read full bulletin
blowing from the center console or cold air blowing from the wireless charging mat area. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
Air Bags & Safety
4 bulletinsThis service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.
This service bulletin provides information on availability for a seat belt extender.
Special Coverage. On certain vehicles, if a driver repeatedly sits on the seat belt cable cover located at the base of...
Read full bulletin
the driver's seat when entering the vehicle, it may cause the seat belt pretensioner to bend sharply over the seat side shield. If this continues to occur over an extended period of time, which is very rare, the seat belt pretensioner cable may fatigue and eventually separate, which could reduce the effectiveness of the vehicle's seat belts. Before any damage occurs to the pretensioner cable itself, signs of wear will be visible on the pretensioner cable cover where it has been repeatedly bent over the seat side shield. Dealers are to replace the pretensioner and side shield for all customers that experience a broken pretensioner cable or come to a dealership with excessive wear on the cable sleeve. The repairs will be made at no charge to the customer.
This informational bulletin provides information on Passenger Presence System (PPS) May Command Seat Belt Reminder Chime...
Read full bulletin
and Passenger Airbag Indicator On or Set DTC B101D When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat
Steering
3 bulletinsThis technical bulletin provides repair information to correct a customer concern of "Steering Assist Is Reduced"...
Read full bulletin
Message and One of The Following DTCs Are Set: C056D, U0415.
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid...
Read full bulletin
reservoir.
This preliminary informational bulletin provides repair information to correct a customer concern of loss of power...
Read full bulletin
steering assist, hard to steer, and/or "Service Power Steering" message on in DIC.
Suspension
2 bulletinsThis technical bulletin provides a procedure to replace both front strut mounts due to a gap between the bearing lower...
Read full bulletin
housing and top mount body.
This technical bulletin provides a procedure to replace both front strut mounts due to a gap between the bearing lower...
Read full bulletin
housing and top mount body.