2011 Chevrolet Equinox TSBs
1,000 Technical Service Bulletins across 17 categories
Categories
Engine
290 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides diagnostic repair information for customer concerns of Engine Run-On, Rough Running,...
Read full bulletin
Malfunction Indicator Lamp (MIL) Illuminated.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
This bulletin updates the position of General Motors on refinishing aluminum wheels.
Read full bulletin
GM has determined that wheel refinishing under warranty will no longer be performed.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
Normal Characteristic - Sub-woofer Is Inoperative With a 2.4L Engine.
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction...
Read full bulletin
Indicator Lamp (MIL) Illuminated.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
Special Coverage Adjustment - Engine Balance Chain and Fuel Pump - Equipped with 2.4L Engine (LAF)
Special Coverage Adjustment - Engine Balance Chain and Fuel Pump - Equipped with 2.4L Engine (LAF)
Special Coverage Adjustment - Engine Balance Chain and Fuel Pump - Equipped with 2.4L Engine (LAF)
Customer Satisfaction Program - Oil Life Monitor Update.
Read full bulletin
Eql;uipped with 2.4L Engine (LAF/LEA)
Customer Satisfaction Program - Oil Life Monitor Update.
Read full bulletin
Eql;uipped with 2.4L Engine (LAF/LEA)
Excessive Oil Consumption ? Perform Oil Consumption Test and/or Install Piston and Piston Ring Kit
Excessive Oil Consumption ? Perform Oil Consumption Test and/or Install Piston and Piston Ring Kit
Excessive Oil Consumption ? Perform Oil Consumption Test and/or Install Piston and Piston Ring Kit
Information for Engine Oils Used in 2014 Model Year Vehicles
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements DTCs P0008, P0009, P0016, P0017, P0018...
Read full bulletin
and/or P0019
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018...
Read full bulletin
and/or P0019
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018...
Read full bulletin
and/or P0019
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018...
Read full bulletin
and/or P0019
Excessive Oil Consumption
Excessive Oil Consumption
Excessive Oil Consumption
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, P0008, P0009, P0016, P0017, P0018 and/or...
Read full bulletin
P0019
Normal Characteristic - Sub-woofer Is Inoperative With a 2.4L Engine.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint.
Read full bulletin
GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides diagnostic repair information for customer concerns of Engine Run-On, Rough Running,...
Read full bulletin
Malfunction Indicator Lamp (MIL) Illuminated.
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction...
Read full bulletin
Indicator Lamp (MIL) Illuminated?.
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine...
Read full bulletin
overheating, cooling system contaminated with engine oil.
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine...
Read full bulletin
overheating, cooling system contaminated with engine oil.
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
LOW AUDIBLE WHINE NOISE FROM ENGINE
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
The inlet flange may have the potential to fatigue and crack at the inlet cone if the engine motor mounts are worn.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC...
Read full bulletin
P0300 that may also be set.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vehicles that have hard start,...
Read full bulletin
extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately...
Read full bulletin
followingHFV6re-manufactured engines replacement.
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately...
Read full bulletin
followingHFV6re-manufactured engines replacement.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if...
Read full bulletin
faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This technical bulletin provides Correction information to find the cause of oil consumption.
Read full bulletin
Techs should perform an oil consumption test first, check for oil leaks and if rate of oil consumption is high, then replace the pistons and the rings.
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for...
Read full bulletin
customer concerns related to wheel alignment.
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as...
Read full bulletin
opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary information communicates the repair recommendations for misfire in HFV6re-manufactured engines.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after...
Read full bulletin
severe internal engine damage.
This technical bulletin provides a procedure to Replace both camshaft position actuator valves to correct a condition of...
Read full bulletin
the engine runs rough, hesitates, hard to start, and or stalls. During diagnosis a technician may find DTCs P0010, P0013, P0011, P0014 set or stored due to camshaft position actuator solenoid valve failure.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact Partechand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
This technical bulletin provides Correction information to find the cause of oil consumption.
Read full bulletin
Techs should perform an oil consumption test first, check for oil leaks and if rate of oil consumption is high, then replace the pistons and the rings.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This informational bulletin provides information of a possible misfire that may happen from incorrect camshafts being...
Read full bulletin
installed in the reman engines.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
12313D - Special Coverage.
Read full bulletin
On some vehicles, equipped with a 2.4L engine (RPO LAF), the chrome layer on the balance chain pins may wear, allowing the chain to stretch. This would cause an engine noise, and if left untreated, could cause the chain to break, leading to engine damage.
This informational bulletin provides information for the dealer technician to gather as much information to help aid...
Read full bulletin
Engineers by completely filling out requested reports.
This informational bulletin provides information on a normal engine operating condition for faster emission warm up...
Read full bulletin
time.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication informs dealer technicians of a potential whining noise that can occur after...
Read full bulletin
servicing the water pump, water pump chain or cylinder head without use of the water pump sprocket holding tool. Dealers are advised this condition is the result of a water pump chain tensioner ratcheting out. The dealer is directed to follow service information to reset the water pump chain tensioner to correct.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Bulletin Provides Information for Repairing Engine Front Cover Oil Leak, Sealing Surface Preparation and Applying...
Read full bulletin
RTV Sealant.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary information communicates to the dealer an issue where the vehicle's engine may stumble and/or stall at startup.
Read full bulletin
The dealer is to evaluate for a faulty aftermarket or incorrect upstream oxygen sensor.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp, service Antilock Braking System, Service Stabilitrak, Service All Wheel Drive, Service Suspension Control, or Hard Steering. Technician may find the following Diagnostic Trouble Codes stored C0196, C0186, C0287, C0710, C0045, C0050, C0800, U0077, U0074, U0125, U0126, U0100, U0101, U0121, U0415, U0432, U0121, and or U0140. Technician should inspect X411 connector for damage or corrosion. Technician will replace any terminals with damage or corrosion.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016,...
Read full bulletin
P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
15810-03 - Special Coverage Revised.
Read full bulletin
On some vehicles that are equipped with a 2.4L engine (RPO LAF), a malfunction-indicator light (MIL) may illuminate due to thermal damage or face erosion of the catalytic converter. This special coverage covers the condition described above for a period of 10 years or 120,000 miles (193,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Replace the catalytic converter.
15810-03 - Special Coverage Revised.
Read full bulletin
On some vehicles that are equipped with a 2.4L engine (RPO LAF), a malfunction-indicator light (MIL) may illuminate due to thermal damage or face erosion of the catalytic converter. This special coverage covers the condition described above for a period of 10 years or 120,000 miles (193,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Replace the catalytic converter.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
15810-02 - Special Coverage (revised warranty section).
Read full bulletin
On some vehicles that are equipped with a 2.4L engine (RPO LAF), a malfunction-indicator light (MIL) may illuminate due to thermal damage or face erosion of the catalytic converter. This special coverage covers the condition described above for a period of 10 years or 120,000 miles (193,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Replace the catalytic converter. The repairs will be made at no charge to the customer.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that have a loud tick...
Read full bulletin
or rattle noise under the hood at all operating conditions. Technician will need to check the lower and oil pressure to the upper end oil pressure. Technician will need to inspect the oil feed orifice in the cylinder head. Technician will clean out and debris found in the orifice.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This preliminary information bulletin provides a information and a procedure on the 2.4L ecotec engine.
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment...
Read full bulletin
may be caused by the fuel pump and/or the fuel injectors and no
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine...
Read full bulletin
Damage.
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start.
Read full bulletin
A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that have a resonance type vibration occurs between 40 to 60 MPH. In most cases the engine must be under a slight load such as Air Conditioning compressor engagement, light throttle, and in 6th gear Torque Converter Clutch applied. Technician will relax the engine and transmission mounts, then the exhaust system by loosening the front pipe studs. Also work down the system disconnecting one exhaust hanger at a time. Then take the vehicle on a test drive to verify there was improvement. If additional steps are required place two sets of exhaust dampeners one set before and one set after the front catalytic converter. It may be required to move the pair of dampeners along the exhaust system to get the best results.
This Preliminary Information communication provides information to the technician about vehicle that may OnStar...
Read full bulletin
inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
THis bulletin provides information on new saddle cap design cylinder heads and usage.
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer...
Read full bulletin
concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
This preliminary bulletin provides additional diagnoses for engine misfires, popping noise after cylinder head or fuel...
Read full bulletin
rail repair.
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine...
Read full bulletin
when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment...
Read full bulletin
may be caused by the fuel pump and/or the fuel injectors and no
This preliminary information bulletin provides information on doing a pressure line test prior to replacement and...
Read full bulletin
removal of the transmission for conditions relating to No Forward, No Reverse, No Crank, Engine Cranks But Will Not Start.
This informational bulletin provides information on the release of 3 high feature v6 timing chain part kits.
Read full bulletin
To help ease the ordering of large amounts of parts during service.
This preliminary information bulletin provides information regarding all the components that are included when ordering...
Read full bulletin
a new service 2.4L Ecotec engine.
This technical bulletin provides a procedure to Replace both camshaft position actuators to correct a condition of the...
Read full bulletin
engine runs rough, hesitates, hard to start, and or stalls. During diagnosis a technician may find DTCs P0010, P0013, P0011, P0014 set or stored due to camshaft position actuator failure.
This technical bulletin provides a procedure to Complete the Circuit/System Verification steps to correct a condition of...
Read full bulletin
Malfunction Indicator Lamp (MIL) - Check Engine Light On, DTC P182E.
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine...
Read full bulletin
when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
This informational bulletin provides information to the technician on what parts of an engine or transmission will...
Read full bulletin
require the PQC to be notified.
This preliminary bulletin explains a normal condition of a customers concern of a rough idle and black smoke on cold...
Read full bulletin
starts.
This technical bulletin provides a procedure to test for oil consumption and install new pistons and rings if no signs...
Read full bulletin
of consumption or oil leaks have been validated.
This preliminary bulletin states to add the DTC symptom byte to the documentation to help aid engineering pinpoint...
Read full bulletin
concerns when trying to locate a root cause.
This informational bulletin provides information to the technician on what parts of an engine or transmission will...
Read full bulletin
require the PQC to be notified.
This technical bulletin provides a procedure to test for oil consumption and install new pistons and rings if no signs...
Read full bulletin
of consumption or oil leaks have been validated.
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment...
Read full bulletin
may be caused by the fuel pump and/or the fuel injectors and no
This informational bulletin provides information for the dealer technician to gather as much information to help aid...
Read full bulletin
Engineers by completely filling out requested reports.
This informational bulletin was provides information for the technician of cold start ticking noises in the engine...
Read full bulletin
compartment and may be caused by the fuel pump and/or the fuel injectors and no repairs are needed for a normal condition.
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder.
Read full bulletin
A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016,...
Read full bulletin
P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative.
Read full bulletin
Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative.
Read full bulletin
Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
This Preliminary Information communication provides information to the technician about customers that may complain of...
Read full bulletin
various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This informational bulletin provides information for engine oil life monitor operation calculation.
This technical bulletin provides a procedure to inspect the fuel system and replace the high pressure fuel pump if...
Read full bulletin
faulty for a Reduced Engine Power, MIL On, DTC P228C condition.
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC...
Read full bulletin
P0300 that may also be set.
This preliminary information bulletin provides information regarding all the components that are included when ordering...
Read full bulletin
a new service 2.4L Ecotec engine.
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly...
Read full bulletin
replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This informational bulletin provides information for repairing engine front cover oil leak, sealing surface preparation...
Read full bulletin
and applying RTV sealant.
This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and...
Read full bulletin
filter.
This informational bulletin annouces the availability of high feature V6 timing chain kits and chain guide replacements,...
Read full bulletin
for repairing stretched timing chains setting DTCs P0008, P0009, P0016, P0017, P0018 and/or P0019.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size...
Read full bulletin
trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size...
Read full bulletin
trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent engine misfire and a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0300, P0301, and/or P0304. Technician will need to follow published Service Information diagnostics first. If the Service Information diagnostics do not isolate a cause for this concern, inspect the inside of the fuel rail and/or fuel tank for fuel contamination. f fuel contamination is present, refer to the "Fuel System Cleaning" procedure in Service Information. Dealer will need to advise the customer to only use fuel from high quality high volume Top Tier fuel stations.
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine,...
Read full bulletin
transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
This preliminary bulletin explains a normal condition of a customers concern of a rough idle and black smoke on cold...
Read full bulletin
starts.
This informational bulletin advises the technician of new timing chains and guides and part numbers.
This technical bulletin provides a replacement for PIP5025F to advise engine replacement is no longer necessary if...
Read full bulletin
"zebra stripes" are present and to outline a related repair procedure.
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM...
Read full bulletin
(Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2 or global diagnostic system 2 (GDS 2)
This informational bulletin provides information for installing a camshaft timing chain kit on the high feature V6.
This informational bulletin provides information for installing a camshaft timing chain kit on the high feature V6.
This informational bulletin provides information for service agents not required to contact product quality center for...
Read full bulletin
CNG, LPG or gasoline engine, transmission and/or transfer case.
This informational bulletin provides information on high feature V6 timing chains kits and chain guide replacements.
This preliminary informational bulletin provides information on Control Solenoid Valve and Transmission Control Module...
Read full bulletin
Assembly Reprogramming with SPS
This preliminary informational bulletin provides information on components that must be transferred over from the...
Read full bulletin
original engine for the Ecotec 2.4L.
Other
186 bulletinsThis preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
New Vehicle Monitoring Programs Section in IVH
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM...
Read full bulletin
technical assistance case using the dealer case management tool.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Loud Rattle Noise on Startup, Rattle Noise Stops in 3 Seconds or Less.
Loud Rattle Noise on Startup, Rattle Noise Stops in 3 Seconds or Less.
Information on Driveline Clunk Noise
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and...
Read full bulletin
verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
Power Seat Height Adjuster Bolt
Intermittent Remote Keyless Entry Inoperative.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
Terminal Test Probe And Replacement Terminal.
Power Lift Gate Does Not Stay Fully Open Or Drifts Down A Few Inches.
Antenna Mast Broken Off From Antenna Base Mount Low Profile Antenna Available
Rear Wiper and/or Front Rain Sense Wipers.
Rear Wiper and/or Front Rain Sense Wipers.
Rear Wiper and/or Front Rain Sense Wipers.
Diagnostic Tip - Unable to Learn RKE Transmitters.
Normal Characteristic - Sub-woofer Is Inoperative.
Intermittent Remote Keyless Entry Inoperative.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
Terminal Test Probe And Replacement Terminal.
Power Lift Gate Does Not Stay Fully Open Or Drifts Down A Few Inches.
Changing Turn-By-Turn Voice Response To Metric Or English Units
Heated Seat Operation After Performing A Remote Vehicle.
PAC Courtesy Transportation Assistance Program
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Information on Driveline Clunk Noise
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
Canadian Customers Unable To Place Calls In The United States
GM TAC Support of Vehicle Vibration Complaints.
Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues
Requesting a New Key Code for Customer with Lost or Stolen Keys
Antenna Mast Broken Off From Antenna Base Mount Low Profile Antenna Available.
Rear Wiper and/or Front Rain Sense Wipers.
Rear Wiper and/or Front Rain Sense Wipers.
Rear Wiper and/or Front Rain Sense Wipers.
Diagnostic Tip - Unable to Learn RKE Transmitters.
Normal Characteristic - Sub-woofer Is Inoperative.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and...
Read full bulletin
verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This informational bulletin provides information on proper use of floor mats.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Essential Tools that Include Consumable Parts (U.S.
Read full bulletin
Only)
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify...
Read full bulletin
the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
IPC Odometer Programming Method Quick Reference Guide
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this...
Read full bulletin
should be considered a normal characteristic.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE...
Read full bulletin
for vehicles that may need an upgrade.
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When...
Read full bulletin
Using the Pico Scope
This informational bulletin explains the importance of maintaining the vehicle.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the...
Read full bulletin
customer.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle.
Read full bulletin
Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles.
Read full bulletin
A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
This informational bulletin provides information on how to use floor mats.
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This Preliminary information communicates
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle.
Read full bulletin
Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
This informational bulletin provides information on how to use floor mats.
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This Preliminary Information communication provides information to the technician about connectivity concerns when...
Read full bulletin
connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
This information bulletin provides the technician the information on how to properly clean a metal surface using the...
Read full bulletin
correct tool.
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a...
Read full bulletin
vehicle.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This information bulletin provides the dealers on how to submit a product information report.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using...
Read full bulletin
Customer Concern Verification Sheets (CCVS).
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar...
Read full bulletin
RemoteLink? phone application.
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital...
Read full bulletin
pictures.
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the...
Read full bulletin
appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the...
Read full bulletin
part numbers for the labels.
This informational bulletin advises the new way required to tow a vehicle when using a dinghy or flat towing.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This bulletin describes the Dealer special tool loan program process.
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and...
Read full bulletin
additional information concerning Policy decision making.
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the...
Read full bulletin
Approved Refinish Materials booklet information.
This preliminary informational bulletin provides a revision of PI0592A to add the 2013 and 2014 model years.
This preliminary informational bulletin provides a revision of PI0602 to add the 2013 and 2014 model years.
This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
This preliminary bulletin provides a procedure to replace the windshild to correct the customers concern of a loose...
Read full bulletin
mirrior and/or bracket fell off.
This preliminary bulletin provides information on how to set the rear electric child locks.
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that...
Read full bulletin
may be un necessary.
This information bulletin provides the technician the information on how to properly clean a metal surface using the...
Read full bulletin
correct tool.
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a...
Read full bulletin
vehicle.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides information on the proper oils to use on GM vehicles including information...
Read full bulletin
regarding the differences of the Dexos oils.
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate...
Read full bulletin
unwanted odors in vehicles and which products to use for each application.
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer...
Read full bulletin
inventory.
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE...
Read full bulletin
for vehicles that may need an upgrade.
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that...
Read full bulletin
may be un necessary.
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that...
Read full bulletin
may be un necessary.
This preliminary bulletin provides information to the technician when replacing the active noise cancellation (ANC)...
Read full bulletin
microphone, there was a design change introduced into production.
This information bulletin provides the technician the information on how to properly clean a metal surface using the...
Read full bulletin
correct tool.
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a...
Read full bulletin
vehicle.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides information on how to use floor mats.
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This informational bulletin explains the Road Force balancers and what they can do for customer concerns.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance...
Read full bulletin
Claim (PAC) within the Courtesy Transportation Assistance Program.
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known...
Read full bulletin
as a Product Allegation Resolution (PAR) claim.
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate...
Read full bulletin
unwanted odors in vehicles and which products to use for each application.
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in...
Read full bulletin
vehicles.
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended...
Read full bulletin
Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
This informational bulletin advises the new way required to tow a vehicle when using a dinghy or flat towing.
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of...
Read full bulletin
torque specifications.
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S.
Read full bulletin
and Canada only).
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to...
Read full bulletin
contact PQC prior to replacing an assembly (U.S. and Canada only).
This preliminary bulletin provides a procedure to replace the IMS if the code can not be reset, with DTC P182E is set.
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications...
Read full bulletin
to Control GM Accessory Remote Start Kits.
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
This information bulletin provides the technician with additional information on fixing the vehicle right the first time...
Read full bulletin
by listing possible concerns to specific vehicles.
This technical bulletin provides a revision for 03-00-89-0061I to add the 2014 model year and Transport Mode heading.
This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.
This informational bulletin provides information for dealers to properly maintain vehicle in inventory.
This informational bulletin provides information on the proper cleaning products for GM hard or plastic surfaces, seats...
Read full bulletin
carpet, vinyl.
This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected...
Read full bulletin
tampering.
This preliminary information bulletin provides a procedure for dust intrusion into the passenger compartment when the...
Read full bulletin
vehicle is driven in high dust areas.
This informational bulletin provides information on fix it right for first time issues.
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible...
Read full bulletin
condition and add a Note in the Instructions section.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
Low Audible Whine Noise has been found to be transmitting from the balance shaft drive chain.
This preliminary informational bulletin provides information on replacement for the auxiliary floor mat retainer due to...
Read full bulletin
the floor mat retainer won't seat on the carpet.
This informational bulletin provides information on the replacement process for the product quality center.
This technical bulletin provides a procedure on suspected tampering due to aftermarket ALDL or DLC interface devices...
Read full bulletin
causing multiple issues.
This informational bulletin provides directions on submitting different PIRs
Pre-Delivery & Maintenance
132 bulletinsThis bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
Vehicle Recalls
Vehicle Recalls
Learning Issues When Repairing Service Stability/Traction Message.
Normal Characteristic - Memory Seat Recall Inoperative From Key Fob.
Learning Issues When Repairing Service Stability/Traction Message.
Service Stability Message With Code U0710
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
Normal Characteristic - Memory Seat Recall Inoperative From Key Fob.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This service bulletin provides information on RDM Axle Ratios for AWD Vehicles for Vibration Diagnostics When Using the...
Read full bulletin
Pico Scope.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on proper use of floor mats.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and...
Read full bulletin
PF48.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398,...
Read full bulletin
E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This warranty administration bulletin provides policy information on required operating procedures.
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the...
Read full bulletin
requirements for the dealer to comply.
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S.
Read full bulletin
and Canada dealers only.
This warranty administration bulletin provide policy information on required operating procedures.
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product...
Read full bulletin
field action customer reimbursement procedure (U.S. Dealers Only).
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is...
Read full bulletin
considered warranty and non-warranty.
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information on required operating procedures.
This informational bulletin provides information for Warranty Administration ? Changes in Powertrain Warranty Coverage ...
Read full bulletin
Effective with 2010 Model Year.
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab...
Read full bulletin
Warranty Information.
This preliminary informational bulletin provides a revision of PI0388B to add the Cadillac XTS model, graphics, improved...
Read full bulletin
Instructions and Warranty Information.
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is...
Read full bulletin
considered warranty and non-warranty.
This preliminary informational bulletin provides service information to the dealer technicians that the remote start...
Read full bulletin
will not work with the ONSTAR REMOTE Link applcation
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor...
Read full bulletin
Operations and Customer Enthusiasm
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that...
Read full bulletin
was at fault of the cutomer and how to properly claim them on the warranty paperwork
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI)...
Read full bulletin
process and to encourage delivering quality vehicles and generating higher CSi scores.
This warranty administration bulletin provides policy information with the field action courtesy transportation policy.
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the...
Read full bulletin
requirements for the dealer to comply.
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what...
Read full bulletin
can be approved by TAC and where the electronic parts can be returned to.
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is...
Read full bulletin
acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
This warranty administration bulletin provides information on GM?s policy for comprehensive courtesy transportation to...
Read full bulletin
its customers.
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is...
Read full bulletin
acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
This warranty administration bulletin provide policy information on the change in product field action customer...
Read full bulletin
reimbursement procedure.
This warranty administration bulletin provide policy information on required operating procedures.
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that...
Read full bulletin
was at fault of the cutomer and how to properly claim them on the warranty paperwork
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for...
Read full bulletin
Service Agents not required to contact PQC prior to assembly replacement.
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the...
Read full bulletin
warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty administration bulletin provide policy information on required operating procedures.
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor...
Read full bulletin
operations and customer enthusiasm.
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential...
Read full bulletin
tools that include consumable parts (U.S. Only).
Electrical
91 bulletinsThis Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
Information on Diagnosing Intermittent Electrical Concerns with Components Fused Through Instrument Panel Fuse Block.
Information on Diagnosing Intermittent Electrical Concerns with Components Fused Through Instrument Panel Fuse Block.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
High Voltage Safety ? High Voltage Disabling
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
HVAC Blows Cold Due To Low System Voltage
Reprogram ECM.
Intermittent No Crank When Ignition Key Is Turned To The Crank.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
HVAC Blows Cold Due To Low System Voltage
Reprogram ECM.
Programming And Activation Of Replacement OnStar Modules.
GM Wiring Repair Strategy Information
OnStar Module Does Not Support All B101D Symptom Codes.
Generation 9 OnStar Modules Inoperative, Bluetooth Inoperative and Possible Battery Discharge Condition (Replace OnStar...
Read full bulletin
VCIM)
Accessory Power Outlet and Trailer Lighting Fuse Replacement Labor Operation N1720 Fuse Replacement
Intermittent No Crank When Ignition Key Is Turned To The Crank.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Special Coverage. On certain 2010-2012 model year and 2016-2017 model year Chevrolet Equinox and GMC Terrain vehicles,...
Read full bulletin
the ball joints in the front windshield wiper modules of these vehicles may experience high corrosion and wear that could result in the separation of one or more ball joints from their sockets during wiper operation. If a ball joint were to separate, one or both of the windshield wipers could become inoperative. Dealers are to inspect the front wiper assembly and replace the wiper linkages or module as necessary. The repairs will be made at no charge to the customer.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This service bulletin provides information on Module Harvesting.
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a...
Read full bulletin
condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
Special Coverage. On certain vehicles, the ball joints in the front windshield wiper modules of these vehicles may...
Read full bulletin
experience high corrosion and wear that could result in the separation of one or more ball joints from their sockets during wiper operation. If a ball joint were to separate, one or both of the windshield wipers could become inoperative. Dealers are to inspect the front wiper assembly and replace the wiper linkages or module as necessary. The repairs will be made at no charge to the customer.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1.
Read full bulletin
IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2 The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin explains to the technician that when using wiring repair labor operations,...
Read full bulletin
additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
This informational bulletin provides information on key code security rules and information on GM keycode look-up...
Read full bulletin
applications.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
This diagnostic tip advises the tech to check if the upstream O2 sensor has been replaced with a faulty or aftermarket ...
Read full bulletin
sensor and how to verify if the sensor is the cause of the concern.
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part...
Read full bulletin
Number in eSI and how to locate the part(s) in the EPC.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles...
Read full bulletin
that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive...
Read full bulletin
finish".
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that may have turn...
Read full bulletin
signal indicators on the Instrument Panel Cluster do not match the audible warnings. Technician will need to test the battery using the GR8. Technician should also verify the charging system is operating correctly.
This informational bulletin provides to the technician, locations to check for possible loose or damaged electrical...
Read full bulletin
connections that may set a DTC instead of just replacing a part.
This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic...
Read full bulletin
control issues.
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with...
Read full bulletin
conductive finish.
This informational bulletin provides information on control module diagnostics and configuration, programming using...
Read full bulletin
the TIS Service Programming System (SPS), set-up and warranty.
This warranty administration bulletin provides policy information on ACDelco replacement battery warranty procedures.
This Preliminary Information communication provides information to the technician about vehicles that the radio can be...
Read full bulletin
turned on after turning the ignition off and opening the driver?s door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a...
Read full bulletin
long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
This preliminary informational bulletin provides information that the tire pressure monitor (TPM) sensors must always...
Read full bulletin
be re-learned when accessory wheels are installed on the vehicle.
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if...
Read full bulletin
it is warranty or not.
This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic...
Read full bulletin
control issues.
This informational bulletin provides information regarding the Passenger Presence System (PPS) May Command Seat Belt...
Read full bulletin
Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat, DTCs 5045 or B0074 0F May Set in PPS Module
This preliminary informational bulletin provides a procedure to reprogram the ECM for concerns regarding a loud rattle...
Read full bulletin
noise on start up that stops in 3 seconds or less.
This preliminary informational bulletin provides a procedure on how to correctly check and adjust fuses within the...
Read full bulletin
instrument panel fuse block for concerns with components fused through the instrument panel fuse block
This warranty administration bulletin provides policy information on ACDelco replacement battery warranty procedures.
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code...
Read full bulletin
E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and...
Read full bulletin
reprogram modules.
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313...
Read full bulletin
Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if...
Read full bulletin
it is warranty or not.
This informational bulletin explains if the fuse is open when the customer plugs in the trailer, that it may be the...
Read full bulletin
cause if diagnostics finds no problems to that point.
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if...
Read full bulletin
it is warranty or not
This preliminary bulletin provides information on what labor operation number to use for various electrical/electronic...
Read full bulletin
control issues.
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
This preliminary informational bulletin provides a procedure to reprogram the ECM for concerns regarding a loud rattle...
Read full bulletin
noise on start up that stops in 3 seconds or less.
This preliminary informational bulletin provides a procedure on how to correctly check and adjust fuses within the...
Read full bulletin
instrument panel fuse block for concerns with components fused through the instrument panel fuse block
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED,...
Read full bulletin
No WiFi Operation, and/or Limited OnStar Module Functionality After OnStar Module Replacement for Another Condition.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel...
Read full bulletin
revised wiring repair labor operations and required additional information.
This Preliminary Information communication provides information to the technicians for diagnosing and repairing vehicles...
Read full bulletin
that have an issue with a pop noise from the fuel tank area after a cold start or Evaporative Emissions System purge. Technician will be able to use Global Diagnostic System 2 to duplicate the concern by commanding a purge and seal on the Evaporative Emissions System. Replacement of the auxiliary fuel pump module assembly will correct this concern.
This informational bulletin communicates GM wiring repair strategy information.
Battery Testing and Warranty Replacement Requirements (North America ONLY)
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This informational bulletin explains how to cut a new key or how to get a precut key from GM.
This informational bulletin provides information accessory power outlet and trailer lighting fuse replacement due to...
Read full bulletin
electrical systems that can be affected by devices that are plugged in by the customer.
This preliminary information bulletin provides information on powertrain and various electronic/electrical control...
Read full bulletin
issues.
This preliminary information bulletin provides a procedure for installing a zip tie for the fuel level sensor to correct...
Read full bulletin
the fuel gauge intermittently not reading full when the fuel tank is filled.
This informational bulletin provides information on suspected tampering on vehicles modifications for identifying non GM...
Read full bulletin
ECM calibrations.
This preliminary informational bulletin provides information on communication interface module replacement.
Body & Paint
62 bulletinsThis PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
Rear and Side Tempered Glass Spots.
Rear Doors Intermittently will not Open from Inside.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
Power Liftgate Does Not Stay Fully Open Or Drifts Down A Few Inches
Power Liftgate Does Not Stay Fully Open Or Drifts Down A Few Inches.
Liftgate Rattles Over Rough Roads.
Liftgate Rattles Over Rough Roads.
A Door May Not Open With The Outside Handle And/Or The Inside Handle.
Wind Buffeting Noise With a Rear Window Down.
Power Liftgate Does Not Stay Fully Open Or Drifts Down A Few Inches
Power Liftgate Does Not Stay Fully Open Or Drifts Down A Few Inches.
Liftgate Rattles Over Rough Roads.
Liftgate Rattles Over Rough Roads.
A Door May Not Open With The Outside Handle And/Or The Inside Handle.
Wind Buffeting Noise With a Rear Window Down.
This service bulletin provides information on Paintless Dent Repair Process.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication provides information to the technician about vehicles that have may a...
Read full bulletin
helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint...
Read full bulletin
percentage.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
Information on Opening Hood When Hood Primary Latch Release Cable is Inoperative Some customers or dealer personnel...
Read full bulletin
may comment that the inside hood release cable is not functioning and they are unable to open the hood.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This Preliminary Information communication provides information to the technician about vehicles that have may a...
Read full bulletin
helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This Preliminary Information communication provides information to the technician about vehicles that have may a...
Read full bulletin
helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
This Preliminary Information communication provides information to the technician about vehicles that have may a...
Read full bulletin
helicopter type noise when a rear window is lowered. This is a normal characteristic of this vehicle, but the concern can be minimized by lowering a front door glass approximately 1 to 2 inches.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication provides information to the technician about vehicles that have a ticking...
Read full bulletin
noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining...
Read full bulletin
when the protective shipping film is removed from certain vehicles.
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of...
Read full bulletin
chromed aluminum wheels, along with warranty information regarding these conditions.
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving...
Read full bulletin
Speeds
This preliminary information bulletin provides a procedure on how to correct the customers concern of a creak or popping...
Read full bulletin
from the windshield area when cold.
The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a...
Read full bulletin
windshield.
This preliminary information bulletin provides information the proper ways of adjusting the center trim bezel to correct...
Read full bulletin
the condition of the CD/DVD will not eject from the instrument panel mounted player.
This informational bulletin provides recommendations and product information for application of anti-corrosion materials
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel...
Read full bulletin
(IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill...
Read full bulletin
the tire can be properly repaired under the new tire warranty.
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal...
Read full bulletin
characteristic.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This preliminary informational bulletin adds the 2016 model year to information to correct a customer concern on opening...
Read full bulletin
hood when hood primary latch release cable is inoperative.
This preliminary informational bulletin provides information for Round Dark Stains on Roof Paint Center Rear Area.
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining,...
Read full bulletin
pitting corrosion and/or spotted.
This preliminary informational bulletin adds the 2017 model year to information to correct a customer concern on opening...
Read full bulletin
hood when hood primary latch release cable is inoperative.
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
Fuel System
44 bulletinsThis service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
Navigation Radio Radio And Integrated Center Stack
Navigation Radio Radio And Integrated Center Stack
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable...
Read full bulletin
diesel fuel.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This Prelimary information informs the dealer of a diagnotic trouble code that may set due to a failed high pressure fuel pump.
Read full bulletin
Dealers are to check fuel pressure as per current testing outlined in GM service information and replace the fuel pump if needed.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This technical bulletin provides a procedure to replace the Aux fuel pump if found the cause of the customers concern.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks...
Read full bulletin
using the evaporative emission cart smoke machine and ultrasonic leak detectortools.
This informational bulletin provides information on top tier fuels and what brands are available.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
This informational bulletin provides information on top tier fuels and what brands are available.
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if...
Read full bulletin
debris have entered the exhaust system.
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER...
Read full bulletin
Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year.
Read full bulletin
Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
This preliminary informational bulletin provides a procedure to reprogram the navigation radio for concerns regarding...
Read full bulletin
Loss of GPS Signal, Low Fuel, XM Volume, Audio Button Functionality, Not Able to Set Clock, Factory Settings Option Inoperable, Radio Display Information May Not Match
This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
This informational bulletin provides information on top tier fuels and what brands are available.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This preliminary informational bulletin provides a procedure to reprogram the navigation radio for concerns regarding...
Read full bulletin
Loss of GPS Signal, Low Fuel, XM Volume, Audio Button Functionality, Not Able to Set Clock, Factory Settings Option Inoperable, Radio Display Information May Not Match
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
Transmission
36 bulletinsThe service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin informs the technician of an alternate lift procedure that has been developed when the lift plate...
Read full bulletin
does not fit the top of the transmission case for 6T30, 6T35, 6T40, 6T45, and 6T50 Transmissions.
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
Harsh 2-3 Shift.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
Timeshift Function Inoperative.
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature...
Read full bulletin
Conditions
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature...
Read full bulletin
Conditions
Power Steering Noise or Fluid Leak from Power Steering Pump, Gear or High Pressure Hose During Extreme Low Temperature...
Read full bulletin
Conditions
Warranty Administration ? Change in Automatic Transmission Add Condition Documentation and Claim Submission
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
Special Coverage. On some vehicles, a link ball socket in the front wiper transmission may separate.
Read full bulletin
If this were to occur, the driver would experience a sudden loss of front wiper function. Dealers are to replace the front wiper transmission kit or module with the latest version with improved sockets and a new water shield. The repairs will be made at no charge to the customer.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
N192266180 - Special Coverage - On some 2010-2012, and 2014-2017 model year Chevrolet Equinox and GMC Terrain vehicles,...
Read full bulletin
a link ball socket in the wiper transmission may separate. If this were to occur, the driver would experience a sudden loss of wiper function. Dealers are to replace the front wiper module with the latest version with improved sockets and a new water shield. The repairs will be made at no charge to the customer.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This informational bulletin provides normal operating characteristics and diagnostic information on Manual...
Read full bulletin
transmissions.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096...
Read full bulletin
TransFlow.
This informational bulletin provides information for Power Steering Noise or Fluid Leak from Power Steering Pump, Gear...
Read full bulletin
or High Pressure Hose During Extreme Low Temperature Conditions
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
This informational bulletin provides technicians with information to assist in identifying operating characteristics of...
Read full bulletin
manual transmissions that repair attempts will not change.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
This preliminary information bulletin provides a procedure to install a revised generator, power steering gear inlet hose and evap.
Read full bulletin
hose to correct steering wheel shudder during low speed maneuvers.
This preliminary bulletin provides a procedure to aid in diagnosing a possible faulty front transmission oil pump.
Tires & Wheels
29 bulletinsThis service bulletin provides information on Tire Sidewall Irregularities.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance,...
Read full bulletin
Shake, Flat Spotting) of GM Original Equipment Tires.
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to...
Read full bulletin
possible chances of the customers concerns over tire vibration are repair.
This informational bulletin provides the technician with information on tire radial force variations and how to use it.
This informational bulletin provides the technician the proper way to install and torque the wheel.
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to...
Read full bulletin
possible chances of the customers concerns over tire vibration are repair.
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow...
Read full bulletin
tire leak and low tire psi message on.
This informational bulletin explains the use of Nitrogen in GM tires.
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to...
Read full bulletin
possible chances of the customers concerns over tire vibration are repair.
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques...
Read full bulletin
used to install wheels onto vehicles
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
This informational bulletin provides the technician with information on tire radial force variations and how to balance...
Read full bulletin
a tire using the balancer.
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to...
Read full bulletin
possible chances of the customers concerns over tire vibration are repair.
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques...
Read full bulletin
used to install wheels onto vehicles
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force...
Read full bulletin
Variations and the difference between balancing a flange and flangeless rim.
This informational bulletin provides information on tire radial force variation.
Software & Calibration
28 bulletinsVehicle Software Enhancements
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
OnStar Voice Fallback Number Update
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This preliminary informational bulletin provides a revision for PI0011C to add the 2013-2014 model years and update...
Read full bulletin
Warranty Information.
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation...
Read full bulletin
Information and Transaction Submissions Procedure and general content updates.
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor...
Read full bulletin
Operation.
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor...
Read full bulletin
Operations.
This informational bulletin provides a revision for 10-00-89-016 to include the 2012-2014 model years and update the...
Read full bulletin
Labor Operation graphic.
This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor...
Read full bulletin
operations.
This preliminary informational bulletin provides a revision of PI0785A to add the 2014 model year, include Encore model...
Read full bulletin
and update the Parts and Warranty Information.
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time...
Read full bulletin
Code and update the tool reference information.
This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor...
Read full bulletin
Operation.
This informational bulletin is a revision for 03-06-03-004G to add the 2014 model year and update the Labor Operation.
This informational bulletin is a revision for 11-00-89-007B to add the 2014 model year and update the Labor Operation...
Read full bulletin
List.
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation...
Read full bulletin
under Courtesy Transportation Warranty Transaction Submission.
This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.
This informational bulletin provides a revision for 03-08-48-006I to add model years and update parts information.
This technical bulletin provides a revision for 04-00-89-015D to update content and incorporate the U.S.
Read full bulletin
version of Bulletin 12-00-89-003.
This preliminary informational bulletin provides a revision for PI0865B to update the Parts Information table to include...
Read full bulletin
Usage and update the Warranty Information.
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
This technical bulletin provides a revision for 13-02-32-001 to update the models information.
This informational bulletin provides technicians with updated information to help identify the differences between what...
Read full bulletin
is considered a fluid leak, and what is considered seepage.
This informational bulletin provides information on a update for the Electronic Component Exchange Program (U.S.
Read full bulletin
and Canada Only)
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
Infotainment
25 bulletinsXM Audio Traffic And Travel Link Availability And Operation.
Information On Requests To Add OnStar Bluetooth Option.
Checking Smartphone Bluetooth Software Update Status
Checking Smartphone Bluetooth Software Update Status
Key Off Radio Operation.
Key Off Radio Operation.
Customer Satisfaction Program - Navigation Radio Loss of Customer Settings
Supplemental Radio Replacement and Programming Instructions.
Supplemental Radio Replacement and Programming Instructions.
This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After...
Read full bulletin
an OnStar In-Vehicle Voice Message Is Heard.
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a...
Read full bulletin
feedback form to the GM navigation disc center website.
This Preliminary Information communication provides information to the technician about vehicles that may have an issue...
Read full bulletin
when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a...
Read full bulletin
feedback form to the GM navigation disc center website.
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions...
Read full bulletin
and to correct the customers concern of the radio being loud during navigation.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a...
Read full bulletin
condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This preliminary informational bulletin provides information onUnexpected Loss of Radio Audio (Radio Goes Silent/No...
Read full bulletin
Sound) and Other Blackberry Phone - Bluetooth Issues Concern.
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions...
Read full bulletin
and to correct the customers concern of the radio being loud during navigation.
This informational bulletin provides information on USB command and control multimedia player interface/list of...
Read full bulletin
supported devices.
This preliminary bulletin provides information to replace the radio to correct the customers concern of multiple Radio...
Read full bulletin
concerns.
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions...
Read full bulletin
and to correct the customers concern of the radio being loud during navigation.
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a...
Read full bulletin
feedback form to the GM navigation disc center website.
This informational bulletin provides information on USB command and control multimedia player interface/list of...
Read full bulletin
supported devices.
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States.
Read full bulletin
While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a...
Read full bulletin
condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc...
Read full bulletin
information.
Lighting
24 bulletinsThis informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and...
Read full bulletin
the Proper use of GM Simplified Maintenance Schedules.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and...
Read full bulletin
recommended practices.
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation...
Read full bulletin
settings for concernc regarding noice drop outs during calls and muffled sound.
This informational bulletin was created to inform that any accessories that are install from the GM factory will be...
Read full bulletin
covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be...
Read full bulletin
covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including...
Read full bulletin
flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
This Preliminary Information communication provides information to the technician about vehicles that show an error...
Read full bulletin
message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
This technical bulletin provides information on Vehicle Software Enhancements for 2014 and prior GM Passenger Cars and...
Read full bulletin
Light Duty Trucks.
Steering
18 bulletinsThis service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or...
Read full bulletin
fluid leak concern that is caused during extremely low temperatures.
Special Coverage Adjustment ? Power Steering Stick-Slip
Service Steering Message or Service Stability Message.
Service Steering Message or Service Stability Message.
A Notchy Or Stick Slip Feel In The Steering When Turning Near The On-Center Position.
Service Steering Message or Service Stability Message.
Service Steering Message or Service Stability Message.
Guidelines For NJ1 Power Steering Powerpack
Guidelines For NJ1 Power Steering Powerpack
A Notchy Or Stick Slip Feel In The Steering When Turning Near The On-Center Position.
This service bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise or...
Read full bulletin
fluid leak concern that is caused during extremely low temperatures.
This technical bulletin provides a procedure to eliminate a power steering noise due to extremely low temperatures.
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise...
Read full bulletin
or fluid leak concern that is caused during extremely low temperatures.
This technical bulletin provides a procedure to flush and bleed power steering system to correct a power steering noise...
Read full bulletin
or fluid leak concern that is caused during extremely low temperatures.
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low...
Read full bulletin
temperatures and use the recommended fluid.
This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low...
Read full bulletin
temperatures and use the recommended fluid.
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid...
Read full bulletin
reservoir.
This preliminary bulletin provides a procedure to replace the power steering hose, generator and evaporative hose to...
Read full bulletin
correct the customers concern of steering shudder at low speeds.
Brakes
17 bulletinsThis service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
Service Stability, Traction, ABS Rear Wheel Speed DTC Or Chassis Expansion
Service Stability Traction ABS Rear Wheel Speed.
Service Stability, Traction, ABS Rear Wheel Speed DTC Or Chassis Expansion
Service Stability Traction ABS Rear Wheel Speed.
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly...
Read full bulletin
abrasive disk on gasket sealing surfaces or reused parts.
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk...
Read full bulletin
on gasket sealing surfaces or reused parts.
This informational bulletin provides information for Disc Brake Warranty Service and Procedures.
This informational bulletin provides technicians with a brake lathe calibration procedure.
HVAC & Climate
10 bulletinsA/C Blows Warm Or Poor Performance.
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS)...
Read full bulletin
concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
This technical bulletin provides repair information for the correction of a customer concern of short duration musty...
Read full bulletin
odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor...
Read full bulletin
emanating from HVAC system.
Air Bags & Safety
5 bulletinsThis service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.
This service bulletin provides information on availability for a seat belt extender.
This preliminary information provides a procedure to repair the seat belt webbing and latch by rolling it back over.
This preliminary informational bulletin provides information on properly repositioning the seat belt webbing/latch...
Read full bulletin
plate due to becoming twisted.
This preliminary informational bulletin provides information on the driver airbag light is flashing in the cluster...
Read full bulletin
and/or the passenger airbag ON indicator does not illuminate when the passenger is present when the SDM setup has not been completed after reprogramming.
Suspension
2 bulletinsThis technical bulletin provides a procedure to add greese to the strut and jounce bumper, to stop the customers...
Read full bulletin
concern of the front suspention or strut making noise.
This preliminary bulletin provides a procedure to install new liftgate struts to correct the customers concern of the...
Read full bulletin
liftgate sagging, causing the gate to close from the open position.
Hybrid & EV
1 bulletinThis technical bulletin provides a revision for 09-00-89-029J to add the 2014 model year and to add the Impala, Spark,...
Read full bulletin
Spark EV, Silverado and Sierra.