2019 Chevrolet Colorado TSBs
979 Technical Service Bulletins across 17 categories
Categories
Engine
267 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston.
This Preliminary information communicates a possible issue with an engine timing chain, gear or crankshaft key.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This informational bulletin advises the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine...
Read full bulletin
hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel in cold temperatures.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
This bulletin updates the position of General Motors on refinishing aluminum wheels.
Read full bulletin
GM has determined that wheel refinishing under warranty will no longer be performed.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension...
Read full bulletin
housing and to perform testing on transmission for other possible issues, but it still may be possible on high mileage vehicles that orifices in housing may have come dislodged, causing the same customer concern.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction...
Read full bulletin
Indicator Lamp (MIL) Illuminated.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This informational bulletin advised the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine...
Read full bulletin
hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel in cold temperatures.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides information for dealers/technicians on Rough Idle, Malfunction Indicator Lamp (MIL)...
Read full bulletin
Illuminated After Engine Repairs with DTCs P0016 and/or P0018 Set.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This technical bulletin provides a procedure to locate and repair a possible short in the wiring harness located at the...
Read full bulletin
camshaft cover or the cylinder head to correct customer concerns of Lack of Power, Reduced Power Displayed on DIC, Rough Idle, Stabilitrak Light On, MIL Illuminated - DTC P0014, P0365, P0366 and P06A3 Set.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides information for after installation of a replacement upper valve body, the transmission...
Read full bulletin
may have no Reverse and no 2nd gear.
This Preliminary information communicates concerns created by an aftermarket ECM calibration installed byfleet companies.
Read full bulletin
The Fleet companies installaftermarket ECM calibrations to limit the vehicle speedto approximately 70 mph andreduce the over all power output. This calibration also reduces the engine idle speed and may induce a vibration at idle. If the vehicle needs to be returned to factory specifications, the ECM must be replaced and programmed.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This service bulletin provides a repair procedure to correct a customer concern of Delayed and/or Harsh Engagement of...
Read full bulletin
Transmission Shift After Vehicle Sitting with Engine Off.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension...
Read full bulletin
housing and to perform testing on transmission for possible other issues, but it still may be possible on high mile vehicles that orifices in housing may have come dislodged, causing the same customer concern.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This engineering information (EI) closure ends the need for further information from the technician in regards to the...
Read full bulletin
crankshaft balancer appearing to be wobbling and/or vibrating, mounting bolt does not appear to be centered.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary information communicates to the dealer technician of a possible concern with the low reverse clutch piston.
Read full bulletin
If the customer is experiencing a no reverse or slip in reverse condition technician are advised to inspect the low reverse clutch piston for being torn. Technicians are advised to replace the low reverse clutch piston and the transmission center support if the low reverse clutch piston is torn.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This service bulletin provides service information for customer concerns of an in-tank fuel pump whining noise, engine...
Read full bulletin
hard to start and/or stalls and Malfunction Indicator Lamp (MIL) is illuminated that may be caused by gelling of fuel in cold temperatures.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This engineering informational bulletin is requesting information from technicians to perform the check list provided...
Read full bulletin
and contact the engineer listed in regards to the crankshaft balancer appears to be wobbling and/or vibrating, mounting bolt does not appear to be centered.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This informational bulletin provides tips for showing a way to confirm if its a mechanical engine issue or not.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger...
Read full bulletin
Whine Noise due to the blades on the turbo being bent.
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an...
Read full bulletin
oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp not being tightened properly.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about vehicles that may have a...
Read full bulletin
vibration at idle in gear or at very low speeds. Technician should inspect for a stray nut or debris such as a rock wedged between the rubber and metal portions of the transmission mount. Technician will need to remove the stray debris.
This Preliminary Information communication provides information to the technician that some vehicle may have a water leak into the cabin.
Read full bulletin
Water staining may be seen in the headliner or water may be on the floor. Technician will inspect these areas for water intrusion roof ditch, rear glass, center high mounted stop light, windshield, cowl seam, heater-vent-air conditioning drain tube, pillar area, and the pressure relief valve.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint.
Read full bulletin
GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).
This service bulletin advises the technician of a diagnostic test for a possible issue with a damaged OCV solenoid that...
Read full bulletin
may cause an oil leak and misfire, illuminating the MIL and setting DTCs P0300, P0302 and/or P0305.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communicates to the technician the potential areas of concern in which the engine wiring harness may chafe.
Read full bulletin
It describes in detail what to look for.If you encounter any of these specific described chafes, inspect, repair (as necessary) and route the wiring harness away from these possible chafe points.
Service Update. On a small number of the vehicles identified above, the electrical connector to the transmission valve...
Read full bulletin
body solenoids may not be fully seated. DTC P2718 or P2720 may set resulting in the Check Engine indicator illuminating, and the transmission reverting to a ?limp home? mode providing limited forward gear selection. Dealers are to access the transmission valve body solenoids and fully seat the connectors.
Service Update. On a small number of the vehicles identified above, the electrical connector to the transmission valve...
Read full bulletin
body solenoids may not be fully seated. DTC P2718 or P2720 may set resulting in the Check Engine indicator illuminating, and the transmission reverting to a ?limp home? mode providing limited forward gear selection. Dealers are to access the transmission valve body solenoids and fully seat the connectors.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides diagnostic strategy information to aid in diagnosing a Ticking, Tap or Rattle Noise from...
Read full bulletin
Engine with Possible Misfire, Malfunction Indicator Lamp (MIL) Illuminated.
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary information communicates concerns created by an aftermarket ECM calibration installed byfleet companies.
Read full bulletin
The Fleet companies installaftermarket ECM calibrations to limit the vehicle speedto approximately 70 mph andreduce the over all power output. This calibration also reduces the engine idle speed and may induce a vibration at idle. If the vehicle needs to be returned to factory specifications, the ECM must be replaced and programmed.
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently...
Read full bulletin
and that engineering is investigating.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently...
Read full bulletin
and that engineering is investigating.
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction...
Read full bulletin
Indicator Lamp (MIL) Illuminated?.
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine...
Read full bulletin
overheating, cooling system contaminated with engine oil.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This technical bulletin provides a procedure to locate and repair a possible short in the wiring harness located at the...
Read full bulletin
camshaft cover or the cylinder head.
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine...
Read full bulletin
overheating, cooling system contaminated with engine oil.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This technical bulletin provides a procedure to locate and repair a possible short in the wiring harness located at the...
Read full bulletin
camshaft cover or the cylinder head.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This service bulletin provides a procedure to correct a customer concern of Engine Noise and/or Belt Squeak, MIL...
Read full bulletin
Illuminated.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary information communicates to technician's if they remove the front timing cover when performing a...
Read full bulletin
repair, they should inspect the timing chain guide upper bolt for being loose. This document is an attempt to collect parts so engineering can investigate the concern.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P06DE set in the Engine Control Module. P0651 may also be set in the ECM with the P06DE. Technician must follow published Service Information diagnostics for P06DE. If diagnostics lead to removing the oil pan or engine oil pressure is below specification when hot, to inspect the oil piston nozzles for damage. Technician should replace the broken oil nozzle(s) as long as the engine does not have any damage which warrants engine replacement.
This Preliminary Information communication provides information to the technician about vehicles that may have a...
Read full bulletin
vibration at idle in gear or at very low speeds. Technician should inspect for a stray nut or debris such as a rock wedged between the rubber and metal portions of the transmission mount. Technician will need to remove the stray debris.
This Preliminary information communicates to the dealer technician diagnostic tips for avibration concern at low engine speeds.
Read full bulletin
If using these diagnostics shows root cause of the vibration to be the transmission torque converter the torque converter should be replaced.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This Preliminary information communicates to the dealer technician to inspect for a missing 1-2-7-8-R clutch fluid...
Read full bulletin
passage seal or incorrect1-2-7-8-R clutch fluid passage seal being install for a no movement concern after valve body replacement on the 8L45 or 8L90 transmissions.
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
Emission - General Motors has decided to conduct a Voluntary Emission Recall involving certain 2017-2020 Chevrolet Colorado and GMC Canyon vehicles.
Read full bulletin
General Motors has determined that evaporative emissions canister service parts that were manufactured during a certain time period and installed in vehicles during a service repair were not manufactured to engineering specifications. Dealers are to inspect the evaporative emissions canister and replace it if the part does not meet engineering specifications.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
Emission - General Motors has decided to conduct a Voluntary Emission Recall involving certain 2017-2020 Chevrolet Colorado and GMC Canyon vehicles.
Read full bulletin
General Motors has determined that evaporative emissions canister service parts that were manufactured during a certain time period and installed in vehicles during a service repair were not manufactured to engineering specifications. Dealers are to inspect the evaporative emissions canister and replace it if the part does not meet engineering specifications.
Emission - General Motors has decided to conduct a Voluntary Emission Recall involving certain 2017-2020 Chevrolet Colorado and GMC Canyon vehicles.
Read full bulletin
General Motors has determined that evaporative emissions canister service parts that were manufactured during a certain time period and installed in vehicles during a service repair were not manufactured to engineering specifications. Dealers are to inspect the evaporative emissions canister and replace it if the part does not meet engineering specifications.
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently...
Read full bulletin
and that engineering is investigating
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
Emission - General Motors has decided to conduct a Voluntary Emission Recall involving certain 2017-2020 Chevrolet Colorado and GMC Canyon vehicles.
Read full bulletin
General Motors has determined that evaporative emissions canister service parts that were manufactured during a certain time period and installed in vehicles during a service repair were not manufactured to engineering specifications. Dealers are to inspect the evaporative emissions canister and replace it if the part does not meet engineering specifications.
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently...
Read full bulletin
and that engineering is investigating
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communicates to the technician the potential areas of concern in which the engine wiring harness may chafe.
Read full bulletin
It describes in detail what to look for.If you encounter any of these specific described chafes, inspect, repair (as necessary) and route the wiring harness away from these possible chafe points.
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently...
Read full bulletin
and that engineering is investigating
This informational bulletin provides tips for showing a way to confirm if its a mechanical engine issue or not.
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger...
Read full bulletin
Whine Noise due to the blades on the turbo being bent.
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an...
Read full bulletin
oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp not being tightened properly.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This engineering informational bulletin is requesting information from technicians to perform the check list provided...
Read full bulletin
and contact the engineer listed in regards a loud bang and/or grinding type noise heard coming from the rear axle area.
This preliminary informational (PI) provides diagnosis and repair information regarding bearing damage or when an engine...
Read full bulletin
will not rotate.
This technical bulletin provides a repair procedure to correct a customer concern of Delayed and/or Harsh Engagement of...
Read full bulletin
Transmission Shift After Vehicle Sitting with Engine Off.
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC...
Read full bulletin
P0300 that may also be set.
This Preliminary information communicates to the dealer technician diagnostic tips for avibration concern at low engine speeds.
Read full bulletin
If using these diagnostics shows root cause of the vibration to be the transmission torque converter the torque converter should be replaced.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary information communicates to the dealer technician diagnostic tips for avibration concern at low engine speeds.
Read full bulletin
If using these diagnostics shows root cause of the vibration to be the transmission torque converter the torque converter should be replaced.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary Information communication provides information to the technician about vehicles that may have a click...
Read full bulletin
or tick noise heard inside cab with engine running.Technician may find the engine or High Pressure Fuel Pump tick noise that is very loud in the cab of the truck.Comparison with another truck having the same powertrain could show the other truck is quieter.Technician will install an acoustic seal that may be missing or dislodged.Update extends to all engines and all model years.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This engineering information (EI) is requesting information from technicians to perform the check list provided and...
Read full bulletin
contact the engineer listed in regards a loud bang and/or grinding type noise heard coming from the rear axle area.
This technical bulletin provides a procedure to replace the center support housing and low reverse piston seal if found...
Read full bulletin
the cause of reverse issues.
Emission - General Motors has decided to conduct a voluntary emissions recall involving certain 2016-2019 model year diesel engine vehicles.
Read full bulletin
The engine control module (ECM) in these vehicles may not adequately diagnose or illuminate the malfunction indicator lamp (Check Engine Light) when frequent regeneration of the diesel particulate filter (DPF) occurs. Dealers are to program the engine control module (ECM) with corrected software.
This Preliminary Information communication provides information to the technician that some vehicle may have a water leak into the cabin.
Read full bulletin
Water staining may be seen in the headliner or water may be on the floor. Technician will inspect these areas for water intrusion roof ditch, rear glass, center high mounted stop light, windshield, cowl seam, heater-vent-air conditioning drain tube, pillar area, and the pressure relief valve.
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a...
Read full bulletin
guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
Emission - General Motors has decided to conduct a voluntary emissions recall involving certain 2018-2019 model year diesel engine vehicles.
Read full bulletin
The engine control module (ECM) in these vehicles may not adequately diagnose or illuminate the malfunction indicator lamp (Check Engine Light) when frequent regeneration of the diesel particulate filter (DPF) occurs. Dealers are to program the engine control module (ECM) with corrected software.
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for...
Read full bulletin
customer concerns related to wheel alignment.
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates to the technician the vehicle concern of starter flex plate having broken teeth.
Read full bulletin
The can create a noise during starting or may even have the starter spin but not crank over the engine.The document directs the technician to replace the flex plate and the starter assembly.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This Preliminary Information communication provides information to the technician about vehicles that may have unwanted volume ramping to max.
Read full bulletin
Dealer should advise the customer General Motors is working on a solution to the concern.
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as...
Read full bulletin
opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This informational bulletin provides tips for showing a way to confirm if its a mechanical engine issue or not.
This engineering informational bulletin is requesting information on the 4WD will not engage when requested.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This engineering informational bulletin is requesting to gather information from the field to determine a root cause for...
Read full bulletin
a condition of oil leaking from the valve rocker arm oil control valve. The information gathered will be used to develop a field fix.
This technical bulletin provides a procedure to replace the turbocharger for vehicles with a condition of Turbocharger...
Read full bulletin
Whine Noise due to the blades on the turbo being bent.
This technical bulletin provides a procedure to Tighten the Charge Air Cooler Duct Clamp to correct a condition of an...
Read full bulletin
oil leak originating from either the inlet or outlet duct of the turbocharger due to the charge air cooler pipe clamp not being tightened properly.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after...
Read full bulletin
severe internal engine damage.
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to...
Read full bulletin
be setting falsely and advises engineering is investigating the concern.
This PI was written to inform dealers of a condition where a "Climate off" message will be displayed on the screen even...
Read full bulletin
thought the HVAC system is fully operational. Dealers are also informed that engineering is working on a solution
This informational bulletin advises the tech that intake camshaft actuator solenoid bank and the intake actuator park...
Read full bulletin
lock solenoid have the same electrical connector and may be swapped causing the concern.
This preliminary information is to alert the service technician of a potential A/C evaporator freezing concern ,...
Read full bulletin
engineering is investigating.
This engineering informational bulletin is requesting information on the 4WD will not engage when requested.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using...
Read full bulletin
the Tech 2 or GDS 2.
This informational bulletin provides information for dealers/technicians on Check Engine Light Illuminated with DTC?s...
Read full bulletin
P0106, P0046, P20EE, P249D, and/or P249E Set.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to...
Read full bulletin
be setting falsely and advises engineering is investigating the concern.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This Preliminary Information communication provides information to the technician about vehicles that may have a click...
Read full bulletin
or tick noise heard inside cab with engine running.Technician may find the engine or High Pressure Fuel Pump tick noise that is very loud in the cab of the truck.Comparison with another truck having the same powertrain could show the other truck is quieter.Technician will install an acoustic seal that may be missing or dislodged.Update extends to all engines and all model years.
This Preliminary Information communication provides information to the technician that some vehicle may have a water leak into the cabin.
Read full bulletin
Water staining may be seen in the headliner or water may be on the floor. Technician will inspect these areas for water intrusion roof ditch, rear glass, center high mounted stop light, windshield, cowl seam, heater-vent-air conditioning drain tube, pillar area, and the pressure relief valve.
This preliminary information explains that engineering is investigating a noise from the B-Pillar of the truck and...
Read full bulletin
repair instructions will be released soon.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This engineering information PI ends the need for information from the field on navigation error message, intermittently...
Read full bulletin
or consistently, that appears on the radio display or instrument cluster while navigation is being used.
This engineering informational bulletin is requesting information for the drivers door window regulator being...
Read full bulletin
inoperative due to possible software.
This informational bulletin provides information for the dealer technician to gather as much information to help aid...
Read full bulletin
Engineers by completely filling out requested reports.
This informational bulletin provides information on OnStar VCIM is currently restricted parts.
Read full bulletin
By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
This informational bulletin provides information on a normal engine operating condition for faster emission warm up...
Read full bulletin
time.
This informational bulletin provides information from engineering that identified 3 possible areas to inspect for a...
Read full bulletin
rattle type noise that is being heard from the instrument area.
This PI was written to inform dealers of a condition where a "Climate off" message will be displayed on the screen even...
Read full bulletin
thought the HVAC system is fully operational. Dealers are also informed that engineering is working on a solution
This Preliminary Information communication provides information to the technician that vehicles may have an Antilock...
Read full bulletin
Braking System or Malfunction Indicator Lamp illuminated. Also Low Brake Fluid lamp on with the master cylinder fluid level is full or a Service Trailer Brake message on the Driver Information Center. Technician may find codes C0035, C0040, C0045, C0050, C0055, C0267, U0121, U0415 or U0420. Technician will need to inspect the Electronic Brake Control Module connector for water intrusion or corrosion on the terminals. If either is found, replace the EBCM and replace the affected terminals. Also remove the tape from the conduit leading to G400 between the main harness and the ground lug.
This Bulletin Provides Information for Repairing Engine Front Cover Oil Leak, Sealing Surface Preparation and Applying...
Read full bulletin
RTV Sealant.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This engineering informational bulletin is requesting information from the field on navigation error message,...
Read full bulletin
intermittently or consistently, that appears on the radio display or instrument cluster while navigation is being used.
This engineering informational bulletin is requesting information on product issue with the door weather strip, door...
Read full bulletin
body fit, and/or rear tail lamp moisture.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This technical bulletin provides a procedure to locate and repair a possible short in the wiring harness located at the...
Read full bulletin
camshaft cover or the cylinder head.
This engineering informational bulletin is requesting information on a coolant leak from the water pump and want...
Read full bulletin
pictures including phone call to the engineer.
This engineering informational bulletin is requesting information on a coolant leak from the water pump and want...
Read full bulletin
pictures including phone call to the engineer.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This Preliminary Information communication provides information to the technician that a whine noise heard from the...
Read full bulletin
automatic transmission fluid pan hear with thethe key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of byte info...
Read full bulletin
to retrieve whileengineering completes further investigation.
This preliminary information describes a concern where the temperature gauge may fluctuate or possibly read higher than expected.
Read full bulletin
Engineering is working towards a fix
This preliminary information is to alert the service technician of a potential A/C evaporator freezing concern ,...
Read full bulletin
engineering is investigating.
This Preliminary Information communicatesinformation to the technician about vehicles that may have a water rush or...
Read full bulletin
gurgle type noise from the center dash area. Engineering is aware of the concern and it is under investigation.Inspect the system for coolant leaks and proper coolant level.No other repairs are to be performed at this time.
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of byte info...
Read full bulletin
to retrieve whileengineering completes further investigation.
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various...
Read full bulletin
noises within the engine as well as some misfire causes.
This Preliminary information communicates to the technician where to find the engine identification tag and what...
Read full bulletin
information on that tag to use during programming of someengine control modules.
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of byte info...
Read full bulletin
to retrieve and of engineering investigation.
This Preliminary information communicates possible concerns and a diagnostic strategy to locate and repair various...
Read full bulletin
noises within the engine as well as some misfire causes.
This Preliminary information communicates diagnostic tips for misfires on active fuel management cylinders and...
Read full bulletin
engineering investigations into cylinder 6 misfire on XT5 and cylinder 4 misfire on LaCrosse both of which are 2017. Changes to Preliminary informationinclude adding MY2018, advising of calibration for previous investigation and adding pictures to identify concern. Also defining calibration update information.
Pre-Delivery & Maintenance
171 bulletinsThis service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may...
Read full bulletin
not pass California smog inspection or smog inspection in other states.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This service bulletin provides repair information to correct a customer concern of Vehicle Will Not Lock and Unlock...
Read full bulletin
(Loss of Active Functions) Crank or Start (Loss of Passive Functions) with DTC P0513 Set.
This service bulletin provides repair information to correct a customer concern of Vehicle Will Lock and Unlock (Active...
Read full bulletin
Functions Work) but Will Not Crank or Start (Loss of Passive Functions Do Not Work).
This service bulletin provides repair information to correct a customer concern of No Crank, No Start, Quick...
Read full bulletin
Start/Stall, No FOB Detected, Key FOBs Inoperative, B3924 00, B3925 00, B3926 00, B3927 00, B3928 00 Set.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles...
Read full bulletin
that request to disable or enable content.
This service bulletin provides information on proper use of floor mats.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin explains how to identify possible DEF system contamination.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides information for dealers/technicians on Over The Air (OTA) and In Market Enhancement (IME)...
Read full bulletin
FAQs.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles...
Read full bulletin
that request to disable or enable content.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides information for dealers/technicians on Over the Air (OTA) and In Market Enhancement (IME)...
Read full bulletin
FAQs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This service bulletin explains how to identify possible DEF system contamination.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This service bulletin provides information on proper use of floor mats.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin explains how to identify possible DEF system contamination.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles...
Read full bulletin
that request to disable or enable content.
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles...
Read full bulletin
that request to disable or enable content.
This service bulletin provides service information for a DEF pump that is unable to build pressure after replacement.
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front...
Read full bulletin
grille or radiator area.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information to inform dealership personnel about Law Enforcement and Government vehicles...
Read full bulletin
that request to disable or enable content.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ (U.S. Only).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and...
Read full bulletin
PF48.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles...
Read full bulletin
that may not pass California smog inspection or smog inspection in other states.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398,...
Read full bulletin
E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This Preliminary information communicates to the technician information on what may be setting DTC P06DE.
Read full bulletin
This is in addition to what is already in the service manual.
This Preliminary information communicates to the technician information on what may be setting DTC P06DE.
Read full bulletin
This is in addition to what is already in the service manual.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Preliminary information communicates to the dealer technicians a service procedure to follow if DTC P206D is...
Read full bulletin
encountered.
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer...
Read full bulletin
Enthusiasm.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This warranty administration bulletin provides policy information on required operating procedures.
Other
123 bulletinsThis preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This PI advises dealers to inspect for a missing pump gasket if the vehicle exhibits no movement following a VB...
Read full bulletin
replacement
New Vehicle Monitoring Programs Section in IVH
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM...
Read full bulletin
technical assistance case using the dealer case management tool.
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin explains to the tech on where to look for a possible concern with the rockers causing the...
Read full bulletin
MIL to illuminate.
This informational bulletin explains to the tech on where to look for a possible concern with the rockers causing the...
Read full bulletin
MIL to illuminate.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and...
Read full bulletin
verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
Customer Satisfaction Program - Certain vehicles may have a 12mm diameter hole on the top surface of the front differential housing.
Read full bulletin
Dealers will inspect for the hole and if present, rebuild the front axle with proper housing.
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and...
Read full bulletin
verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicates the potential for a wire chafe to cause intermittent communications concerns...
Read full bulletin
and multiple MIL's on in the IPC.
This informational bulletin explains to the tech on where to look for a possible concern with the rockers causing the...
Read full bulletin
MIL to illuminate.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This informational bulletin explains how to identify possible DEF contamination.
This technical bulletin provides a procedure to replace the rear axle c-clips if found the cause of the customers...
Read full bulletin
concern of rear axle clunk.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
This technical bulletin provides a procedure to replace the rear axle c-clips if found the cause of the customers...
Read full bulletin
concern.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin explains how to identify possible DEF contamination.
This informational bulletin explains how to check the NOx Catalyst Reductant-Load Adaptive Values using GSD2.
This preliminary information was released to advise of an alternate means of purging the airfrom the cooling system.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This informational bulletin provides technicians and dealership personnel with spray-in bed liner general information...
Read full bulletin
and repair procedures.
This Preliminary information communicates a process to correct theconcern of Unable to contact OnStar after the 3G EOL...
Read full bulletin
on 2015-2022 model year vehicles in the United States.
This preliminary information is to clarify a normal fluctuation of the temperature gauge.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicates diagnostic assistance for DTC's P219A and P219B.
This informational bulletin provides information on proper use of floor mats.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This Preliminary information communicates additional diagnostic information for DTC's P0016 and P0018.
This Preliminary information communicates additional diagnostic information for DTC's P0016 and P0018.
This Preliminary information communicates the potential for a wire chafe to cause intermittent communications concerns...
Read full bulletin
and multiple MIL's on in the IPC.
This Preliminary information communicates additional diagnostic information for DTC's P0016 and P0018.
This Preliminary information communicates the potential for a wire chafe to cause intermittent communications concerns...
Read full bulletin
and multiple MIL's on in the IPC.
This technical bulletin provides a procedure to replace the rear axle c-clips if found the cause of the customers...
Read full bulletin
concern.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This informational bulletin explains how to identify possible DEF contamination.
This technical bulletin provides a procedure to replace the surge tank if found the cause of the customers concern.
This informational bulletin explains how to check the NOx Catalyst Reductant-Load Adaptive Values using GSD2.
This informational bulletin provides information ticking noise and/or noise when turning vehicle off.
This preliminary information shows how to inspect for and correct a rattle from the rear seat latches.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
This Preliminary information communicates a possible noise from the water pump causing a DTC and the diagnostics for the...
Read full bulletin
repair.
This technical bulletin advises that the code may be false and it should be cleared and then take the vehicle for a test...
Read full bulletin
drive to verify the code will not return and advise the customer of how the code may set during certain driving conditions.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this...
Read full bulletin
should be considered a normal characteristic.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This Preliminary information communicates additional diagnostic information for DTC's P0016 and P0018.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended,...
Read full bulletin
causing the parking pawl to engage while driving.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This technical bulletin provides a procedure to replace the oil filter insert if found missing or damaged and the cause...
Read full bulletin
of the customers concern.
This technical bulletin provides a procedure to replace either the axle or the bearing depending if there is a lip on...
Read full bulletin
the axle after pulling it.
This technical bulletin provides a procedure to inspect the PCV fresh air and foul air connectors for proper...
Read full bulletin
connections.
This preliminary information was released to advise of an alternate means of purging the airfrom the cooling system.
This Preliminary information communicates that the owner's manual may be confusing to a customer in regards to towing...
Read full bulletin
the vehicle behind another vehicle.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This technical bulletin provides repair information to correct a customer concern of Phone Ringer Volume Turned Down or...
Read full bulletin
Too Quiet.
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin explains how to identify possible DEF contamination.
This technical bulletin provides a procedure to correct a condition of Vibration and/or Noise Heard During Hard...
Read full bulletin
Acceleration at Speeds of 77 km/h (48 mph) to 83 km/h (52 mph).
This informational bulletin provides information to check and verify that no leaks are found and clean the flux build up...
Read full bulletin
using a good brush.
This preliminary information shows how to inspect for and correct a rattle from the rear seat latches.
This Preliminary information communicates the potential for a wire chafe to cause intermittent communications concerns...
Read full bulletin
and multiple MIL's on in the IPC.
This technical bulletin provides a procedure to correct a left lean condition due to architectural corner mass...
Read full bulletin
distribution.
This informational bulletin advises the technician to test the induction system for leaks for any of the codes listed.
This preliminary information is to clarify a normal fluctuation of the temperature gauge.
This preliminary information was released to advise of an alternate means of purging the airfrom the cooling system.
This Preliminary Information communication advises the technician about the narrowing of the bedrails.
Read full bulletin
When installing a bed rail accessory the concern is made visible. This is a characteristic of the sleek design of the vehicle and no repair is necessary. Please communicate to the customer this condition is a normal design characteristic of their vehicle.
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
This informational bulletin explains how to check the NOx Catalyst Reductant-Load Adaptive Values using GSD2.
This informational bulletin provides information ticking noise and/or noise when turning vehicle off.
This Preliminary information communicates a possible concern of two connectors being swapped during a repair causing a...
Read full bulletin
P0016 code to set.
This Preliminary information communicates the potential for a wire chafe to cause intermittent communications concerns...
Read full bulletin
and multiple MIL's on in the IPC.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This technical bulletin provides a procedure to replace the surge tank if found the cause of the customers concern.
This informational bulletin provides information to check and verify that no leaks are found and clean the flux build up...
Read full bulletin
using a good brush.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This Preliminary Information communication advises the technician about the narrowing of the bedrails.
Read full bulletin
When installing a bed rail accessory the concern is made visible. This is a characteristic of the sleek design of the vehicle and no repair is necessary. Please communicate to the customer this condition is a normal design characteristic of their vehicle.
This preliminary information was released to advise of an alternate means of purging the airfrom the cooling system.
This preliminary information is to clarify a normal fluctuation of the temperature gauge.
This informational bulletin provides information on proper use of floor mats.
This technical bulletin provides a procedure to replace the oil filter insert if found missing or damaged and the cause...
Read full bulletin
of the customers concern.
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended,...
Read full bulletin
causing the parking pawl to engage while driving.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information for dealers/technicians on Driver Seat Cushion Design Changes, Driver...
Read full bulletin
and Passenger Cushion Appear Different Thickness.
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as attended causing...
Read full bulletin
the parking pawl to engage while driving.
This preliminary information is to clarify a normal fluctuation of the temperature gauge.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the...
Read full bulletin
customer.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This Preliminary information communicates a possible noise from the water pump causing a DTC and the diagnostics for the...
Read full bulletin
repair.
This preliminary information shows how to inspect for and correct a rattle from the rear seat latches.
Transmission
84 bulletinsThis PI communicates the proper part numbers for transmission connectors and internal harness to prevent confusion when...
Read full bulletin
ordering
This PI communicates the proper part numbers for transmission connectors and internal harness to prevent confusion when...
Read full bulletin
ordering
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and...
Read full bulletin
repair of 8 Speed Transmissions
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed...
Read full bulletin
engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
This Preliminary information communicates for Technicians installing a Service Replacement Transmission Assembly to...
Read full bulletin
contact Technical Assistance to make sureunit is not suspect of a snap ring concern prior to installation.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if...
Read full bulletin
found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.
This Preliminary information communicates diagnostic information for vehicles with transmission noise.
This Preliminary information communicates diagnostic information for vehicles with transmission noise
This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if...
Read full bulletin
found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if...
Read full bulletin
found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This technical bulletin provides a procedure for the techs to replace the forward check ball and separator plate if...
Read full bulletin
found the cause of the customers concern of No Forward Gear When Shifting from Park to Drive and/or Reverse to Drive.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary information communicates to have the dealer contact TAC with the transmission TUN number prior to...
Read full bulletin
transmission installation.
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First...
Read full bulletin
Start Up/Shift of the Day Under Light Throttle.
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring...
Read full bulletin
harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and...
Read full bulletin
repair of 8 Speed Transmissions
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the...
Read full bulletin
t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by Rear of Transmission or Transfer Case Area.
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First...
Read full bulletin
Start Up/Shift of the Day Under Light Throttle.
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This information advises the technician the difference between a welch cap leak and the output seal of the t-case or...
Read full bulletin
transmission leaking ATF causing the customers concern.
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed...
Read full bulletin
engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare...
Read full bulletin
after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This informational bulletin explains how the trans slip or flare can be a normal condition.
This informational bulletin advises the technician of possibly installing the incorrect 1-2-7-8-R clutch fluid passage...
Read full bulletin
seal and which seal should be used with measurements of the seal.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First...
Read full bulletin
Start Up/Shift of the Day Under Light Throttle.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried...
Read full bulletin
to shift the t-case from 4lo to Hi gears while driving.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This service bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or...
Read full bulletin
shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This informational bulletin advises the tech of a possible normal condition when the vehicle creeps forward during start...
Read full bulletin
up conditions when the clutch packs are full of residual oil.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been...
Read full bulletin
repaired for the flare and its still noticed.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare...
Read full bulletin
after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring...
Read full bulletin
harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried...
Read full bulletin
to shift the t-case from 4lo to Hi gears while driving.
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring...
Read full bulletin
harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring...
Read full bulletin
harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
This Preliminary information communicates to the dealer technician that the part numbers for the internal wiring...
Read full bulletin
harnesses for the 8 speed RWD transmissions are not listed in the Electronic Parts Catalog. Technicians are to refer to the information provided in this document to obtain the internal wiring harness part numbers by application.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been...
Read full bulletin
repaired for the flare and its still noticed.
N192217820 - Service Update Bulletin.
Read full bulletin
The current transmission fluid may cause the customer to experience a shake or shudder feeling, which may be described as driving over rumble strips or rough pavement. Dealers are to drain the old transmission fluid and refill with the new fluid.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This technical bulletin provides a procedure to replace the torque converter and inspect the front pump and the TEHCM...
Read full bulletin
for metal.
This technical bulletin provides information for new transmission oil to use, a procedure for exchanging the old fluid...
Read full bulletin
and adding the new fluid to a service transmission.
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a...
Read full bulletin
customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This informational bulletin provides normal operating characteristics and diagnostic information on Manual...
Read full bulletin
transmissions.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or...
Read full bulletin
shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.
This Preliminary information communicates the noise iso later for the shift boot may be out of position deforming the...
Read full bulletin
leather or allowing noise into the cabin.
Electrical
68 bulletinsThis Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no...
Read full bulletin
DTC'ss
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no...
Read full bulletin
DTC's
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no...
Read full bulletin
DTC's
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no...
Read full bulletin
DTC's
This PI Addresses a possible solenoid wiring fault and how to inspect the build date to identify
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use...
Read full bulletin
for certain repairs, such as Wiring Harness Repairs.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
This technical bulletin provides a procedure to inspect and repair possible locations to wiring shorts in the wiring...
Read full bulletin
harness or wiring harness contact areas they may cause shorts.
This technical bulletin provides a procedure to inspect and repair possible locations to wiring shorts in the wiring...
Read full bulletin
harness or wiring harness contact areas they may cause shorts.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This technical bulletin advises the technician of possible concerns caused by failed or incorrectly installed parts that...
Read full bulletin
may cause the battery positive cable to contact the water pump pulley or alternator.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This service bulletin provides information on Module Harvesting.
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a...
Read full bulletin
condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have the battery is discharged overnight. Technician will need to inspect X301 for bent pins as shown below. Repair or replace terminals as needed.
This technical bulletin provides a procedure to inspect and repair possible locations to wiring shorts in the wiring...
Read full bulletin
harness or wiring harness contact areas they may cause shorts.
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded...
Read full bulletin
on the ECM or and detection of a power up hardware installed.
This service bulletin provides service information on a New Way to Look at NOx Sensor Readings and Exhaust Temperature...
Read full bulletin
During a DPF Regeneration or a Reductant System Malfunction Warning Service Bay Test.
Customer Satisfaction.
Read full bulletin
In certain vehicles, certain types of off-road use can, in rare cases, cause the vehicle?s roof-rail air bags and seat belt pretensioners to deploy. Dealers will reprogram the sensing and diagnostic module (SDM) with updated software.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Power Steering message, loss of power and or Malfunction Indicator Lamp on in the Instrument Panel Cluster. Technician will inspect terminals for circuits 2500 and 2501 at the transfer case control module connector, X103 and X106 for oversized or bent terminals. Technician should fix and terminal issues.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have a fuel gauge that does not read below half a tank. Technician will gain access to the fuel pump and inspect to see if the level sender contacting the side of the fuel tank. The fuel tank fuel pump module fuel level sensor will need to be replaced for this concern.
This preliminary information serves as a diagnostic aid for a condition where the ignition switch may not rotate all the...
Read full bulletin
way back to the lock position when the ignition is turned off and addresses areas to look for resolution.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary information communicatesa noise from the front end over bumps originating at the battery hold down...
Read full bulletin
retainer at inner fender.
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance...
Read full bulletin
that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded...
Read full bulletin
on the ECM or and detection of a power up hardware installed.
This service bulletin provides service information on a New Way to Look at NOx Sensor Readings and Exhaust Temperature...
Read full bulletin
During a DPF Regeneration or a Reductant System Malfunction Warning Service Bay Test.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have the battery is discharged overnight. Technician will need to inspect X301 for bent pins as shown below. Repair or replace terminals as needed.
This warranty administration bulletin explains to the technician that when using wiring repair labor operations,...
Read full bulletin
additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
This informational bulletin provides information on key code security rules and information on GM keycode look-up...
Read full bulletin
applications.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
This technical bulletin provides a procedure on how to properly identify if there is any aftermarket calibrations loaded...
Read full bulletin
on the ECM or and detection of a power up hardware installed.
This Preliminary information communicates the possible setting of B101D-39 in the OnStar module and advises of over the...
Read full bulletin
air software update to resolve the concern.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have a fuel gauge that does not read below half a tank. Technician will gain access to the fuel pump and inspect to see if the level sender contacting the side of the fuel tank. The fuel tank fuel pump module fuel level sensor will need to be replaced for this concern.
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part...
Read full bulletin
Number in eSI and how to locate the part(s) in the EPC.
This Preliminary information communicatesa noise from the front end over bumps originating at the battery hold down...
Read full bulletin
retainer at inner fender.
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance...
Read full bulletin
that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have a fuel gauge that does not read below half a tank. Technician will gain access to the fuel pump and inspect to see if the level sender contacting the side of the fuel tank. The fuel tank fuel pump module fuel level sensor will need to be replaced for this concern.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have the battery is discharged overnight. Technician will need to inspect X301 for bent pins as shown below. Repair or replace terminals as needed.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Power Steering message, loss of power and or Malfunction Indicator Lamp on in the Instrument Panel Cluster. Technician will inspect terminals for circuits 2500 and 2501 at the transfer case control module connector, X103 and X106 for oversized or bent terminals. Technician should fix and terminal issues.
This Preliminary Information communication provides information to the technician about vehicles that have "Service 4...
Read full bulletin
Wheel Drive" message on the Driver Information Center. Provides the technician with additional information to ensure that the TCCM contains the latest software released to address previous issues, also advises of default action changes. Calls out specific circuits to be inspected to help isolate intermittent codes.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive...
Read full bulletin
finish".
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have a fuel gauge that does not read below half a tank. Technician will gain access to the fuel pump and inspect to see if the level sender contacting the side of the fuel tank. The fuel tank fuel pump module fuel level sensor will need to be replaced for this concern.
This Preliminary information communicates to the dealer technician that there may be a temporary condition leading to...
Read full bulletin
Reductant Quality Sensor Circuit Low Voltage DTC P206C. This condition may occur after a sustained right hand turn maneuver with a low fill DEF tank that clears shortly after the maneuver.
This Preliminary information communicates to the technician when diagnosing intermittent circuit concerns to look at the...
Read full bulletin
connector for missing weather pack seals that could allow water intrusion into the connector and lead to corrosion on the terminals.
Fuel System
55 bulletinsThis warranty administration bulletin provides policy information on vehicles outside of a California Emissions State...
Read full bulletin
who move to and register their vehicle in a California Emission State may be entitled to the 7 year, 70,000-mile Emission Select State Component Limited Warranty.
This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for...
Read full bulletin
analysis.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the...
Read full bulletin
cause of excessive soot from the tailpipe.
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
This informational bulletin provides information on Clean Exhaust Filter See Owner Manual Now or Cleaning Exhaust Filter...
Read full bulletin
Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information on availability of Diesel Fuel additives.
This service bulletin provides information on availability of Diesel Fuel additives.
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the...
Read full bulletin
cause of excessive soot from the tailpipe.
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This service bulletin provides information on availability of Diesel Fuel additives.
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the...
Read full bulletin
cause of excessive soot from the tailpipe.
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information on availability of Diesel Fuel additives.
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable...
Read full bulletin
diesel fuel.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information on availability of Diesel Fuel additives.
This service bulletin provides a diagnostic aid procedure on how to perform a quick test to check if the DPF is the...
Read full bulletin
cause of excessive soot from the tailpipe.
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This Informational Bulletin provides information on availability of Diesel Fuel additives.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of...
Read full bulletin
excessive soot from the tailpipe.
This informational bulletin provides information on Diesel Exhaust Fluid (DEF) and the proper use of the DEF system.
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of...
Read full bulletin
excessive soot from the tailpipe.
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the...
Read full bulletin
part and ordering it from the EPC.
This Preliminary Infiormation relates to air condition performanceissues that can occur if bulletin19-NA-177 for air...
Read full bulletin
conditioning evaporator freeze up is performed on vehicles not in the geographical areas where this can occur.
This informational bulletin provides information on Clean Exhaust Filter See Owners Manual Now or Cleaning Exhaust...
Read full bulletin
Filter Keep Driving Until Message is Cleared messages Displayed on DIC, DTC P2463 May Be Set.
This Preliminary Information communication provides information to the technician that some vehicle may have an ?Exhaust...
Read full bulletin
Fluid Quality Poor? on the Driver Information Center or a diesel exhaust fluid warning lamp on or other exhaust fluid quality related concerns. Technician will inspect the diesel exhaust fluid for contamination. Technician should use Service Information for Contaminants in Diesel Exhaust Fluid Diagnosis and use special tool J26568 or EN50422 Diesel Exhaust Fluid Refractometer for fluid testing.
This Informational Bulletin provides information on availability of Diesel Fuel additives.
This informational bulletin provides information for dealers/technicians on Lack of A/C performance, Evaporator freeze...
Read full bulletin
up.
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of...
Read full bulletin
excessive soot from the tailpipe.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This informational bulletin provides a procedure on how to perform a quick test to check if the DPF is the cause of...
Read full bulletin
excessive soot from the tailpipe.
This technical bulletin provides a procedure to replace the Emission Reduction Fluid Controller if found the cause of...
Read full bulletin
the customers concern.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
Body & Paint
52 bulletinsThis preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the...
Read full bulletin
shipping film.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides information on Paintless Dent Repair Process.
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables.
Read full bulletin
Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
This technical bulletin provides a procedure to correct the condition of Water leak and/or Wet Carpet.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This technical bulletin provides repair information to correct a customer concern of the extended cab rear door ajar...
Read full bulletin
indicator illuminated intermittently.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables.
Read full bulletin
Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This Preliminary Information communication provides information to the technician about vehicles that have a hood that...
Read full bulletin
may shake or flutter while driving. Technician will need to adjust the hood bumpers for this concern.
This Preliminary Information communication provides information to the technician about vehicles that have raised dents...
Read full bulletin
or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Technician should first access the rear of the inner wheelhouse area through the tail lamp cavity and the front of the wheelhouse from under the vehicle, and coat the inner hem of the wheel house to side outer panel with 3M Rust Fighter I. After allowing the 3M Rust Fighter I to dry then apply several coats of Nox Rust X-121B undercoating.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint...
Read full bulletin
percentage.
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and...
Read full bulletin
that it is considered a normal condition.
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables.
Read full bulletin
Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
This Preliminary Information communication provides information to the technician about vehicles that have raised dents...
Read full bulletin
or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Technician should first access the rear of the inner wheelhouse area through the tail lamp cavity and the front of the wheelhouse from under the vehicle, and coat the inner hem of the wheel house to side outer panel with 3M Rust Fighter I. After allowing the 3M Rust Fighter I to dry then apply several coats of Nox Rust X-121B undercoating.
This Preliminary Information communication provides information to the technician about vehicles that have raised dents...
Read full bulletin
or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Technician should first access the rear of the inner wheelhouse area through the tail lamp cavity and the front of the wheelhouse from under the vehicle, and coat the inner hem of the wheel house to side outer panel with 3M Rust Fighter I. After allowing the 3M Rust Fighter I to dry then apply several coats of Nox Rust X-121B undercoating.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This technical bulletin provides repair information to correct a customer concern of ticking type noise heard from the...
Read full bulletin
driver and/or passenger side center pillar upper trim panel structure, on bumpy roads.
This technical bulletin provides repair information to correct a customer concern of the extended cab rear door ajar...
Read full bulletin
indicator illuminated intermittently.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This technical bulletin provides repair information to correct a customer concern of seeing a water leak coming from the...
Read full bulletin
rear window area.
This technical bulletin provides repair information to correct a customer concern of ticking type noise heard from the...
Read full bulletin
driver and/or passenger side center pillar upper trim panel structure, on bumpy roads.
This Preliminary Information communication provides information to the technician about vehicles that have a hood that...
Read full bulletin
may shake or flutter while driving. Technician will need to adjust the hood bumpers for this concern.
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This informational bulletin explains how the DEF filler pipe grommet can possible expand to the filler cap causing the...
Read full bulletin
cap not to seal properly.
This Preliminary Information communication provides information to the technician about vehicles that have raised dents...
Read full bulletin
or ripple appearance in the side outer panel of the cargo box around the perimeter of the wheel house opening. Technician should first access the rear of the inner wheelhouse area through the tail lamp cavity and the front of the wheelhouse from under the vehicle, and coat the inner hem of the wheel house to side outer panel with 3M Rust Fighter I. After allowing the 3M Rust Fighter I to dry then apply several coats of Nox Rust X-121B undercoating.
This informational bulletin provides information for dealers/technicians and customers on the elimination of a glove box...
Read full bulletin
dampener, when unlatched the glove box door falls open.
This informational bulletin provides information for dealers/technicians and customers on the elimination of a glove box...
Read full bulletin
dampener, when unlatched the glove box door falls open.
This bulletin provides information regarding the SDM Reprogramming needed after an AEV Bison Style Front Bumper Package...
Read full bulletin
Installation onto a Colorado ZR2.
This technical bulletin provides repair information to correct a customer concern of the extended cab rear door ajar...
Read full bulletin
indicator illuminated intermittently.
This technical bulletin provides a procedure for installing screws to the center pillar upper trim panel structure on...
Read full bulletin
the affected sides to eliminate the ticking type noise.
This technical bulletin provides repair information to correct a customer concern of seeing a water leak coming from the...
Read full bulletin
rear window area.
This Preliminary Information communication provides information to the technician about vehicles that may have slack in one of the tailgate cables.
Read full bulletin
Technician should not replace any parts for this concern. Please communicate to the customer this condition is a normal operating characteristic of their vehicle.
This Preliminary Information communication provides information to the technician about vehicles that have a hood that...
Read full bulletin
may shake or flutter while driving. Technician will need to adjust the hood bumpers for this concern.
This Preliminary information communicates direction to lubricate a noisy water pump shaft seal with coolant in the weap...
Read full bulletin
hole.
Lighting
41 bulletinsAmendments to the Song-Beverly Act (SBA) California warranty law provides vehicle owners with an opportunity to submit a...
Read full bulletin
written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the affected vehicles will be mailed an owners manual and warranty insert containing this information in English and Spanish.
Amendments to the Song-Beverly Act (SBA) California warranty law provides vehicle owners with an opportunity to submit a...
Read full bulletin
written notice to GM before filing a lawsuit seeking a vehicle repurchase. If such a notice is not provided to GM, then the vehicle owner is prevented from seeking civil penalties in litigation. Vehicle owners of the applicable vehicles will be mailed an owners manual and warranty insert containing this information in English and Spanish.
This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or...
Read full bulletin
Replaced During Warranty Coverage Period.
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or...
Read full bulletin
Replaced During Warranty Coverage Period.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This Preliminary information communicates to dealers of a known issue with failed map update
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This service bulletin provides service information to correct a customer concern of Malfunction Indicator Lamp (MIL)...
Read full bulletin
Illuminated on Driver Information Center (DIC) with DTCs P0171, P0174 Set.
This service bulletin provides information on Dealer Installed LPO Wheel Installation and Return Process.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This Preliminary Information communication advises the technicianto inspect for aftermarket accessory lamps for a loss...
Read full bulletin
of remote functions.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This Preliminary Information communicates the steps on diagnosing the concern of theaccessory off road lamps are...
Read full bulletin
inoperative after installation.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This Preliminary Information communicates the steps on diagnosing the concern of theaccessory off road lamps are...
Read full bulletin
inoperative after installation.
This Preliminary Information communication advises the technicianto inspect for aftermarket accessory lamps for a loss...
Read full bulletin
of remote functions.
This Preliminary Information communicates the steps on diagnosing the concern of theaccessory off road lamps are...
Read full bulletin
inoperative after installation.
This Preliminary Information communication advises the technicianto inspect for aftermarket accessory lamps for a loss...
Read full bulletin
of remote functions.
This Preliminary Information communicates the steps on diagnosing the concern of theaccessory off road lamps are...
Read full bulletin
inoperative after installation.
This Preliminary Information communicates the steps on diagnosing the concern of theaccessory off road lamps are...
Read full bulletin
inoperative after installation.
This Preliminary Information communicates the steps on diagnosing the concern of theaccessory off road lamps are...
Read full bulletin
inoperative after installation.
This Preliminary Information communicates the steps on diagnosing the concern of theaccessory off road lamps are...
Read full bulletin
inoperative after installation.
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and...
Read full bulletin
the Proper use of GM Simplified Maintenance Schedules.
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During...
Read full bulletin
Warranty Coverage Period.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This Preliminary Information communication advises the technicianto inspect for aftermarket accessory lamps for a loss...
Read full bulletin
of remote functions.
This technical bulletin provides repair information to correct a customer concern of Intermittent OnStar Inoperative,...
Read full bulletin
DTC B101D-39, Red LED and Clock Date Time Inaccurate.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This Preliminary Information communicates the steps on diagnosing the concern of theaccessory off road lamps are...
Read full bulletin
inoperative after installation.
This preliminary information advises if the fog lamp indicator is inoperative after the fog lamp kit is installed the...
Read full bulletin
instrument cluster needs to be reprogrammed.
Brakes
36 bulletinsThis Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to...
Read full bulletin
be setting falsely or is induced by the customer.
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when...
Read full bulletin
theForward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for dealers/technicians on Stone Chip/Membrane Damage, Broken Connector...
Read full bulletin
and/or Sensor Retaining Tabs, and/or Paint Damage of Park Assist Sensors.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to...
Read full bulletin
be setting falsely or is induced by the customer.
This Preliminary Information communication provides information to the technician about installing an aftermarket Trailer Brake Controller.
Read full bulletin
Technician will find that that vehicle is not equipped with Trailering Package Regular Production Option Code Z82, there are also blunt cut wires at the spare tire for the trailer connector. Technician will install the aftermarket Trailer Brake Controller to the blunt wires behind the lefts side kick panel. Technician will install the trailer connector to the blunt wires under the vehicles near the spare tire.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to...
Read full bulletin
be setting falsely or is induced by the customer.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to...
Read full bulletin
be setting falsely or is induced by the customer.
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to...
Read full bulletin
be setting falsely or is induced by the customer.
This preliminary information discusses potential for a code C0010.5A to store in the brake controller which appears to...
Read full bulletin
be setting falsely or is induced by the customer.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle...
Read full bulletin
that may have a "Check Trailer Wiring" or "Service Trailer Brake System? message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake system that is being used. The Chassis Control Module can be sensitive to a variety of trailer wiring issues. The technician will need to make a trailer tester using Electric Trailer Brake Magnets and 7-way trailer connector to determine if it is a vehicle or trailer issue. If the concern is not duplicated with the tester installed, the vehicle is operating correctly and the focus should be on the trailer wiring or 7 way connector.
This Preliminary Information communication provides information to the technician about installing an aftermarket Trailer Brake Controller.
Read full bulletin
Technician will find that that vehicle is not equipped with Trailering Package Regular Production Option Code Z82, there are also blunt cut wires at the spare tire for the trailer connector. Technician will install the aftermarket Trailer Brake Controller to the blunt wires behind the lefts side kick panel. Technician will install the trailer connector to the blunt wires under the vehicles near the spare tire.
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly...
Read full bulletin
abrasive disk on gasket sealing surfaces or reused parts.
This Preliminary Information communication provides information to the technician about installing an aftermarket Trailer Brake Controller.
Read full bulletin
Technician will find that that vehicle is not equipped with Trailering Package Regular Production Option Code Z82, there are also blunt cut wires at the spare tire for the trailer connector. Technician will install the aftermarket Trailer Brake Controller to the blunt wires behind the lefts side kick panel. Technician will install the trailer connector to the blunt wires under the vehicles near the spare tire.
Infotainment
24 bulletinsThis service bulletin provides repair information to correct a customer concern of Radio Resets or Reboots and May...
Read full bulletin
Display myBrand Splash Animation.
This service bulletin provides information for dealers/technicians on Handsfree Apple Iphone Call Static conditions...
Read full bulletin
equipped with IOB Radio.
This service bulletin provides repair information to correct a customer concern of software issues with Radio Software...
Read full bulletin
Version V808.
This service bulletin provides information to aid a dealer/customer concern of Radio Unwanted Phantom Touch or...
Read full bulletin
Non-Responsive to Touch After Cleaning/Disinfecting Radio Display.
This service bulletin provides information to aid a dealer/customer concern of Radio Unwanted Phantom Touch or...
Read full bulletin
Non-Responsive to Touch After Cleaning/Disinfecting Radio Display.
This technical bulletin provides repair information to correct a customer concern of Unwanted Radio Volume Ramp Up to...
Read full bulletin
Max, Radio Resets, Radio Display Blank, or Non-Responsive to Touch.
This Preliminary information communicates a concern where the wrong part number was being installed causing XM and Audio concerns.
Read full bulletin
This PI explains the concern and advises to return the part to the ESC for the correct part if the incorrect part number is received
This technical bulletin provides repair information to correct a customer concern of Unwanted Radio Volume Ramp Up to...
Read full bulletin
Max.
This technical bulletin provides repair information to correct a customer concern of software issues with Radio Software...
Read full bulletin
Version V808.
This technical bulletin provides repair information to correct a customer concern of software issues with Radio Software...
Read full bulletin
Version V808.
This Technical bulletin provides a procedure for dealers/technicians on Radio Software Version V807 Over-the-Air Update.
This Technical bulletin provides information for dealers/technicians on Radio Software Version V805 Over-the-Air Update...
Read full bulletin
Release.
This Technical bulletin provides information for dealers/technicians on Radio Software Version V805 Over-the-Air Update...
Read full bulletin
Release.
This informational bulletin provides information on Loss of Phone Pairing or Favorites, Last Setting of Volume, Station,...
Read full bulletin
App, and Audio Settings Change When Vehicle Shuts Down in Demo Mode and that this is considered a normal characteristic of the vehicle in demo mode.
This technical bulletin provides repair information to correct a customer concern of Sirius XM Radio Stations Missing or...
Read full bulletin
SXM Favorites Greyed Out.
This Technical bulletin provides steps for dealers/technicians to change Wi-Fi hotspot displaying myCadillac for SSID...
Read full bulletin
name.
This Preliminary information communicates that acustomer may complain of when a Bluetooth call is received the ringing...
Read full bulletin
will be continuous for the rest of the drive cycle . It may be noted that this only seems to occur when using an Android device on OS 9.0. This may be caused by a software concern in the phone. The dealer is instructed that the phone manufactureris working on a software update to resolve the concern.
This Technical bulletin provides procedure information for dealers/technicians on Radio Software Version V803...
Read full bulletin
Over-the-Air Update.
This Preliminary information communicates that acustomer may complain of when a Bluetooth call is received the ringing...
Read full bulletin
will be continuous for the rest of the drive cycle . It may be noted that this only seems to occur when using an Android device on OS 9.0. This may be caused by a software concern in the phone. The dealer is instructed that the phone manufactureris working on a software update to resolve the concern.
This bulletin provides service procedure information for dealers/technicians on Radio Software Version V509 Over-the-Air...
Read full bulletin
Update.
This informational bulletin provides information for dealers/technicians on a blank or distorted 7 inch radio display...
Read full bulletin
during radio replacement.
This bulletin provides service procedure information for dealers/technicians on Radio Software Version V509 Over-the-Air...
Read full bulletin
Update.
This informational bulletin provides information on Loss of Phone Pairing or Favorites, Last Setting of Volume, Station,...
Read full bulletin
App, and Audio Settings Change When Vehicle Shuts Down in Demo Mode and that this is considered a normal characteristic of the vehicle in demo mode.
This Preliminary information communicates that acustomer may complain of when a Bluetooth call is received the ringing...
Read full bulletin
will be continuous for the rest of the drive cycle . It may be noted that this only seems to occur when using an Android device on OS 9.0. This may be caused by a software concern in the phone. The dealer is instructed that the phone manufacture is working on a software update to resolve the concern.
Tires & Wheels
20 bulletinsThis service bulletin provides information on Tire Sidewall Irregularities.
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM...
Read full bulletin
Vehicles.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance,...
Read full bulletin
Shake, Flat Spotting) of GM Original Equipment Tires.
This service bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak test to...
Read full bulletin
prime the pump.
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak...
Read full bulletin
test to prime the pump.
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak...
Read full bulletin
test to prime the pump.
This informational bulletin advises the technician on what to do if the DEF pump has been replaced and perform a leak...
Read full bulletin
test to prime the pump.
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for...
Read full bulletin
GM Vehicles.
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
Software & Calibration
12 bulletinsThis service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This informational bulletin explains how the SOOT readings went from grams to percentage.
Read full bulletin
2-1-18 Change Subject to reflect the test procedure. 5-1-18 Updated the Information section.
Service Update. Message to resume programming.
Service Update. Message to stop programming.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides information and a service procedure for dealers/technicians on OnStar Over the Air Update...
Read full bulletin
for TTY / TDD Operation and Continuous Improvement Changes.
This informational bulletin explains how the SOOT readings went from grams to percentage.
Read full bulletin
2-1-18 Change Subject to reflect the test procedure. 5-1-18 Updated the Information section.
This informational bulletin explains how the SOOT readings went from grams to percentage.
Read full bulletin
2-1-18 Change Subject to reflect the test procedure. 5-1-18 Updated the Information section.
This Preliminary information communicates information to dealers advising certain Over the air updates and USB updates...
Read full bulletin
have been temporarily suspended.
This Preliminary information communicates information to dealers advising certain Over the air updates and USB updates...
Read full bulletin
have been temporarily suspended.
Suspension
11 bulletinsThis technical bulletin provides a procedure for lubricating the rear leaf springs and re-torque the bolts to correct a...
Read full bulletin
squeak, clunking noise.
This technical bulletin provides a procedure for lubricating the rear leaf springs and re-torque the bolts to correct a...
Read full bulletin
squeak, clunking noise.
This technical bulletin provides a procedure for lubricating the rear leaf springs and re-torque the bolts to correct a...
Read full bulletin
squeak, clunking noise.
This technical bulletin provides a procedure for lubricating the rear leaf springs and re-torque the bolts to correct a...
Read full bulletin
squeak, clunking noise.
This technical bulletin provides a procedure for lubricating the rear leaf springs and re-torque the bolts to correct a...
Read full bulletin
squeak, clunking noise.
This technical bulletin provides a procedure for lubricating the rear leaf springs and re-torque the bolts to correct a...
Read full bulletin
squeak, clunking noise.
This technical bulletin provides a procedure for lubricating the rear leaf springs and re-torque the bolts to correct a...
Read full bulletin
squeak, clunking noise.
This preliminary information suggests the technician verify a noise from the rear is or isn't coming from the rear leaf...
Read full bulletin
springs before a service on the springs is performed.
This technical bulletin provides a procedure for lubricating the rear leaf springs and re-torque the bolts to correct a...
Read full bulletin
squeak, clunking noise.
This preliminary information suggests the technician verify a noise from the rear is or isn't coming from the rear leaf...
Read full bulletin
springs before a service on the springs is performed.
This preliminary information suggests the technician verify a noise from the rear is or isn't coming from the rear...
Read full bulletin
leaf springs before a service on the springs is performed.
HVAC & Climate
8 bulletinsThis service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold...
Read full bulletin
weather climates and testing those batteries.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
This informational bulletin is for Korea to see normal operation of A/C compressor.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
This technical bulletin provides repair information to correct a customer concern of Radio Displays Climate Off Message...
Read full bulletin
or HVAC Popup Displays Different Settings.
This technical bulletin provides repair information to correct a customer concern of Radio Displays Climate Off Message...
Read full bulletin
or HVAC Popup Displays Different Settings.
This technical bulletin provides a procedure to replace the A/C compressor if found with 5 rib pulley and the cause of...
Read full bulletin
the customers concerns.
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS)...
Read full bulletin
concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
Air Bags & Safety
4 bulletinsThis Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.
This Preliminary information communicates assistance in locating theRear seat belt comfort guidesin the parts catalog.
This service bulletin provides information on availability for a seat belt extender.
This technical bulletin provides a procedure to program the SDM and replace the airbags and pretensioners if deployed.
Hybrid & EV
2 bulletinsThis service bulletin provides information on AGM batteries that require less frequent charging in storage.
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
Steering
1 bulletinThis informational bulletin provides information for the customer to pair their phone in order for the push to talk...
Read full bulletin
button on the steering wheel control to work.