2011 Chevrolet Camaro TSBs
1,000 Technical Service Bulletins across 17 categories
Categories
Engine
269 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
This bulletin updates the position of General Motors on refinishing aluminum wheels.
Read full bulletin
GM has determined that wheel refinishing under warranty will no longer be performed.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction...
Read full bulletin
Indicator Lamp (MIL) Illuminated.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
Information for Engine Oils Used in 2014 Model Year Vehicles
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements DTCs P0008, P0009, P0016, P0017, P0018...
Read full bulletin
and/or P0019
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018...
Read full bulletin
and/or P0019
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018...
Read full bulletin
and/or P0019
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, DTCs P0008, P0009, P0016, P0017, P0018...
Read full bulletin
and/or P0019
Information on High Feature V6 Timing Chain Kits and Chain Guide Replacements, P0008, P0009, P0016, P0017, P0018 and/or...
Read full bulletin
P0019
New Service Cam Bearings For Gen IV V8 Engines
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides information for after installation of a replacement upper valve body, the transmission...
Read full bulletin
may have no Reverse and no 2nd gear.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint.
Read full bulletin
GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides steps the technician will uses to diagnose and repair vehicles that...
Read full bulletin
have low oil pressure after an oil change with the engine Regular Production Option Code L20, L77, L94, L96, L99, L9H, LC8, LC9, LH9, LMF, LMG, LY6, or LZ1. Vehicle may have Service Engine Soon lamp with Diagnostic Trouble Code P0521 or Low Oil Pressure message on the instrument panel. Dealer will need to determine if bulletin 10-06-01-008 was completed. If the bulletin was performed inspect the left rocker cover. Dealer will insure the left rocker can hold water without leaking. If leaks are found apply room temperature vulcanization silicone to the rocker cover if possible or replace the left rocker cover.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This service bulletin provides a repair procedure to correct a customer concern of Coolant and/or Oil Leak, Malfunction...
Read full bulletin
Indicator Lamp (MIL) Illuminated?.
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine...
Read full bulletin
overheating, cooling system contaminated with engine oil.
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This service bulletin provides diagnostic information for the technician regarding a customer concern of engine...
Read full bulletin
overheating, cooling system contaminated with engine oil.
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This SKU is a Power Window Regulator and Motor Assembly.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.
This service bulletin provides diagnostic aid procedure to perform inspections to determine if the engine needs to be...
Read full bulletin
replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC...
Read full bulletin
P0300 that may also be set.
This Technical bulletin provides a procedure to correct a condition of Active Fuel Management (AFM) Engine Valve Lifter...
Read full bulletin
Tick Noise at Start Up When Engine Has Been Off for 2 Hours or More.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vehicles that have hard start,...
Read full bulletin
extended crank, or black smoke from the exhaust when starting. Technician will need to perform fuel quality test, spark test, and a compression test. Technician should also install a vacuum gauge prior to cold start and watch needle for signs of a sticking valve.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately...
Read full bulletin
followingHFV6re-manufactured engines replacement.
This Preliminary Information communication provides information to the technician about vehicles that have a belt squeak...
Read full bulletin
noise and/or a crankshaft balancer appears to be out of balance or wobbling while watching it with the engine running. Technician will need to check crankshaft balancer run out. If the balancer run out is greater than 0.40mm, replace the crankshaft balancer.
This Preliminary information communicates the repair recommendations for misfire and DTC's immediately...
Read full bulletin
followingHFV6re-manufactured engines replacement.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses. Also updated to include ALL HFV6 engines Gen1 and Gen2.
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for...
Read full bulletin
customer concerns related to wheel alignment.
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This technical bulletin provides a procedure to perform inspections to determine if the engine needs to be replaced as...
Read full bulletin
opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
This diagnostic tip provides information to the tech to aid in performing a diagnostic test to verify if the camshaft...
Read full bulletin
alignment pin has been sheared away.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary information communicates the repair recommendations for misfire in HFV6re-manufactured engines.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after...
Read full bulletin
severe internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have low oil...
Read full bulletin
pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact Partechand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Code P2097 or P2099. Technician will need to perform an injector balance or Active Fuel Injector Tester prior to going further. Technician will also need to check for a small leak in the exhaust if published Service Information diagnostics does not lead to a resolution.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This informational bulletin provides information of a possible misfire that may happen from incorrect camshafts being...
Read full bulletin
installed in the reman engines.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin explains the normal characteristics of exhaust noise during active fuel management when in...
Read full bulletin
Three or Four Cylinder Mode.
This informational bulletin provides information for the dealer technician to gather as much information to help aid...
Read full bulletin
Engineers by completely filling out requested reports.
This informational bulletin provides information on a normal engine operating condition for faster emission warm up...
Read full bulletin
time.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Bulletin Provides Information for Repairing Engine Front Cover Oil Leak, Sealing Surface Preparation and Applying...
Read full bulletin
RTV Sealant.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that a whine noise heard from the...
Read full bulletin
automatic transmission fluid pan hear with thethe key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates the identification process for High Feature V6 camshafts in re-manufactured...
Read full bulletin
engines.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016,...
Read full bulletin
P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have oil mixed in with the engine coolant. Technician will need to inspect the oil cooler if equipped for possible leaking into the cooling system through the radiator. If no issue found replace the engine as well as all rubber coolant hoses.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment...
Read full bulletin
may be caused by the fuel pump and/or the fuel injectors and no
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine...
Read full bulletin
Damage.
This preliminary informational bulletin provides technicians an engine repair tip for installation of pistons.
This Preliminary Information communication provides information to the technician about vehicle that may have black smoke on a cold start.
Read full bulletin
A dual-pulse injection strategy is utilized during engine cold start to reduce the time required to bring the catalytic converter up to operating temperature. This split injection strategy lasts for about 60 seconds on cold start. This process may cause the customer to see increased black smoke during cold start and should be considered normal.
This Preliminary Information communication provides information to the technician about vehicle that may OnStar...
Read full bulletin
inoperative and Navigation/GPS/Compass issues. Technician may find Diagnostic Trouble Codes B101D sym 3C and or F0. Technician will gather data using a scan tool and contact General Motors Technical Assistance Center for further assistance. After approval technician will replace the OnStar module.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Technician will find Diagnostic Trouble Code P0521. Technician will check the oil filter part number. If the part number is PF48E change the oil filter to a PF48. If a PF48 is not available then install a new UPF48R.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Technician will find Diagnostic Trouble Code P0521. Technician will check the oil filter part number. If the part number is PF48E change the oil filter to a PF48. If a PF48 is not available then install a new PF48E.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on during a cold start in temperatures below 0 degrees Fahrenheit. Technician will find Diagnostic Trouble Code P0521. Technician will check the oil filter part number. If the part number is PF48E change the oil filter to a PF48.
This Preliminary Information communication provides information to the technician about three different conditions some...
Read full bulletin
vehicles may have with the Fog Lamps. First condition that the fog lamps are inoperative and the vehicle is vehicle is equipped with the High Intensity Discharge headlamps Regular Production Option Code T4F. This is a normal operating characteristic. No repairs are recommended. The second condition is that fog lamps are inoperative and the vehicle is vehicle is equipped with the halogen headlamps Regular Production Option Code T4A. This is also a normal operating characteristic based on the vehicle build. Fog lamps were not offered on the LS trim level coupes. The third condition would be the customer asking for the fog lamps to be added or turned on. General Motors does not have an approved fog lamp kit that can be installed on a Camaro that was not originally equipped with that feature.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
THis bulletin provides information on new saddle cap design cylinder heads and usage.
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer...
Read full bulletin
concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition.
This preliminary bulletin provides additional diagnoses for engine misfires, popping noise after cylinder head or fuel...
Read full bulletin
rail repair.
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine...
Read full bulletin
when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment...
Read full bulletin
may be caused by the fuel pump and/or the fuel injectors and no
This informational bulletin provides information on the release of 3 high feature v6 timing chain part kits.
Read full bulletin
To help ease the ordering of large amounts of parts during service.
This informational bulletin provides a process to the service agents that are not required to contact PQC, to determine...
Read full bulletin
when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.
This informational bulletin provides information to the technician on what parts of an engine or transmission will...
Read full bulletin
require the PQC to be notified.
This informational bulletin explains a normal condition from changes in Exhaust Tone for Active Fuel Management Engines...
Read full bulletin
when in Three or Four Cylinder Mode
This preliminary bulletin states to add the DTC symptom byte to the documentation to help aid engineering pinpoint...
Read full bulletin
concerns when trying to locate a root cause.
This informational bulletin provides information to the technician on what parts of an engine or transmission will...
Read full bulletin
require the PQC to be notified.
This informational bulletin was created to inform the technician of cold start ticking noises in the engine compartment...
Read full bulletin
may be caused by the fuel pump and/or the fuel injectors and no
This informational bulletin provides information for the dealer technician to gather as much information to help aid...
Read full bulletin
Engineers by completely filling out requested reports.
This informational bulletin was provides information for the technician of cold start ticking noises in the engine...
Read full bulletin
compartment and may be caused by the fuel pump and/or the fuel injectors and no repairs are needed for a normal condition.
This Preliminary Information communication provides information to the technician with information regarding high misfire rates always on #1 cylinder.
Read full bulletin
A customer may complain of misfires or roughness on cold start up with a P0300 diagnostic trouble code. Technician is to add coolant dye to the system and run the engine through warm up to circulate the dye. Pressurize the cooling system after a cold soak and inspect the cylinder with a bore scope for coolant dye. Dye is used to identify coolant over residual fuel being that might be left in the cylinder. The technician is not to replace the cylinder head as it will not correct this concern. In some cases it is necessary to remove the head for inspection. Do not replace the engine for small surface pock marks or a pitting appearance this is normal and do not connect to coolant passages. Usually if porosity is present there will be a break in the carbon ring. Only replace the engine if true porosity is found. Technician is to call Product Quality Center with the latest version of bulletin 02-07-30-029 if porosity is found and engine replacement is required.
This Preliminary Information communication provides information to the technician that Diagnostic Trouble Codes P0016,...
Read full bulletin
P0017, P0018, P0019, P0008 or P0009 may be set. Technician will need to inspect for loose timing chains or tensioners. If after following Service Information diagnostics the root cause is not found inspect the reluctor for the crankshaft sensor. If the reluctor has moved then replace crankshaft.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative.
Read full bulletin
Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
This Preliminary Information communication provides information to the technician about vehicles that the keyless entry is inoperative.
Read full bulletin
Technician should inspect the ignition key cylinder door sticks in the up position. If the door is found open do not replace the ignition key cylinder, use a Lubriplate type of lubrication spray and lubricate the ignition key cylinder door. Insert the tip of the key in and out to verify the door of the cylinder is not sticking.
This Preliminary Information communication provides information to the technician about customers that may complain of...
Read full bulletin
various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This informational bulletin provides information for engine oil life monitor operation calculation.
This Bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and DTC...
Read full bulletin
P0300 that may also be set.
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly...
Read full bulletin
replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This informational bulletin provides information for repairing engine front cover oil leak, sealing surface preparation...
Read full bulletin
and applying RTV sealant.
This informational bulletin provides technicians with diagnostic tips for preventing oil leaks after changing oil and...
Read full bulletin
filter.
This informational bulletin annouces the availability of high feature V6 timing chain kits and chain guide replacements,...
Read full bulletin
for repairing stretched timing chains setting DTCs P0008, P0009, P0016, P0017, P0018 and/or P0019.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size...
Read full bulletin
trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size...
Read full bulletin
trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine,...
Read full bulletin
transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
This informational bulletin advises the technician of new timing chains and guides and part numbers.
This informational bulletin provides information of suspected tampering or vehicle modifications for non-GM...
Read full bulletin
(Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2 or global diagnostic system 2 (GDS 2)
This preliminary information bulletin provides a procedure for a low and reverse and 1-2-3-4- clutch housing overhaul to...
Read full bulletin
eliminate a bump, surge or vibration at an idle in drive at a stop.
This informational bulletin provides information for installing a camshaft timing chain kit on the high feature V6.
This informational bulletin provides information for installing a camshaft timing chain kit on the high feature V6.
This informational bulletin provides information for service agents not required to contact product quality center for...
Read full bulletin
CNG, LPG or gasoline engine, transmission and/or transfer case.
This technical bulletin provides a procedure to install AFM oil deflector, rocker arm cover-left bank and clean carbon...
Read full bulletin
from cylinder due to engine oil consumption on aluminum block/iron block engines.
This informational bulletin provides information on high feature V6 timing chains kits and chain guide replacements.
This technical bulletin provides a procedure to install the updated valve cover for models built with the prior date...
Read full bulletin
listed to correct oil consumption of vehicles with higher mileage.
This informational bulletin provides information for installing the camshaft timing chain kit for the high feature V6...
Read full bulletin
timing chain kits.
This technical bulletin provides a procedure for the master cylinder reservoir replacement due to brake fluid is seeping...
Read full bulletin
from the master cylinder reservoir cap.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon and may also have an oil or coolant leak. Technician may find coolant or oil in a spark plug tube. If the Spark Plug Tube is leaking and it is determined that the oil or coolant is not coming from a leak above the spark plug then replace the cylinder Head, spark plug and coil.
This Preliminary Information communication provides information to the technician about vehicles that have an engine oil odor with no oil leaks found.
Read full bulletin
Technician will need to inspect for an external oil leak. Technician will need to ensure the oil level is correct. Technician will need to replace the rear main seal, if no oil leaks were found and the engine oil level is not over full.
Other
182 bulletinsThis preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
New Vehicle Monitoring Programs Section in IVH
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM...
Read full bulletin
technical assistance case using the dealer case management tool.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Information on COAX Repair Kit Availability.
Retrofit Procedure.
Retrofit Procedure.
Information on Driveline Clunk Noise
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and...
Read full bulletin
verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
Power Seat Height Adjuster Bolt
There is a quality concern with the Camaro Remote Start kit
Intermittent Remote Keyless Entry Inoperative.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
Diagnostic Tip - Unable to Learn RKE Transmitters.
Intermittent Remote Keyless Entry Inoperative.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
Changing Turn-By-Turn Voice Response To Metric Or English Units
Power Folding Top Diagnostic Tips
Power Folding Top Diagnostic Tips
Power Folding Top Diagnostic Tips
Oil Canning Or Pop Noise In Rear Seat Area
Unable To Remove Bolt
Ratchet Click or Grind Noise In Front Of Vehicle Traveling Straight At Slow Speeds.
Heated Seat Operation After Performing A Remote Vehicle.
GM Accessories Remote Vehicle Start Kit Missing Transmitters
Important - Assistance For Installing The Camaro Ground Effects.
High Intensity Discharge.
High Intensity Discharge.
PAC Courtesy Transportation Assistance Program
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Car and Truck Fix it Right the First Time Issues
Information on Driveline Clunk Noise
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
Canadian Customers Unable To Place Calls In The United States
GM TAC Support of Vehicle Vibration Complaints.
Aftermarket ALDL or DLC Interface Devices Causing Multiple Issues
Requesting a New Key Code for Customer with Lost or Stolen Keys
Diagnostic Tip - Unable to Learn RKE Transmitters.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin advises the tech to validate if oil is leaking into the cooling system and to test and...
Read full bulletin
verify were to leak is coming from before replacing all the parts that wouldn't apply to the repair.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This informational bulletin provides information on proper use of floor mats.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Essential Tools that Include Consumable Parts (U.S.
Read full bulletin
Only)
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify...
Read full bulletin
the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
IPC Odometer Programming Method Quick Reference Guide
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This Preliminary Information communicates helpful information on diagnosing generalcustomer concerns related to a power...
Read full bulletin
folding top.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on Clicking/Ticking Sound/Noise Heard During Cold Start and that this...
Read full bulletin
should be considered a normal characteristic.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communicates helpful information on diagnosing generalcustomer concerns related to a power...
Read full bulletin
folding top.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE...
Read full bulletin
for vehicles that may need an upgrade.
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin explains the importance of maintaining the vehicle.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This Preliminary Information communicates how to correctly care for the decals that are available on these vehicles.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the...
Read full bulletin
customer.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle.
Read full bulletin
Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles.
Read full bulletin
A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
This informational bulletin provides information on how to use floor mats.
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This Preliminary information communicates
This Preliminary Information communication provides information to the technician being unable to program fobs to the vehicle.
Read full bulletin
Technician will need to ensure the key FOB is a new unit and has not been programmed to another vehicle previously.
This informational bulletin provides information on how to use floor mats.
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This Preliminary Information communication provides information to the technician about connectivity concerns when...
Read full bulletin
connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
This information bulletin provides the technician the information on how to properly clean a metal surface using the...
Read full bulletin
correct tool.
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a...
Read full bulletin
vehicle.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This information bulletin provides the dealers on how to submit a product information report.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This informational bulletin adds 2014 - 2015 model years to information regarding comeback prevention and using...
Read full bulletin
Customer Concern Verification Sheets (CCVS).
This preliminary informational bulletin provides information that accessory remote start does not work with OnStar...
Read full bulletin
RemoteLink? phone application.
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital...
Read full bulletin
pictures.
This informational bulletin provides a vibration analysis worksheet the technician can use in conjunction with the...
Read full bulletin
appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the...
Read full bulletin
part numbers for the labels.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This bulletin describes the Dealer special tool loan program process.
This informational bulletin provides a revision for 11-00-89-005D to add additional Mandatory Minimum Tables and...
Read full bulletin
additional information concerning Policy decision making.
This informational bulletin provides a revision for 02-08-98-002C to add the 2010-2013 model years and revise the...
Read full bulletin
Approved Refinish Materials booklet information.
This preliminary informational bulletin provides a revision of PI0592A to add the 2013 and 2014 model years.
This preliminary informational bulletin provides a revision of PI0408 to add the 2012-2014 model years.
This informational bulletin is a revision for 10-00-89-005B to add the 2014 model year and labor codes.
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
This preliminary bulletin provides a procedure to replace the windshild to correct the customers concern of a loose...
Read full bulletin
mirrior and/or bracket fell off.
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that...
Read full bulletin
may be un necessary.
This information bulletin provides the technician the information on how to properly clean a metal surface using the...
Read full bulletin
correct tool.
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a...
Read full bulletin
vehicle.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This information bulletin provides the dealers on how to submit a product information report.
This preliminary information bulletin provides a step by step procedure for retrofitting the convertible top for a new...
Read full bulletin
corded folding top to the original design frame.
This informational bulletin provides a list off all the issues revolving around new vehicles for a one stop place to...
Read full bulletin
find growing concerns around them.
This informational bulletin provides information on the proper oils to use on GM vehicles including information...
Read full bulletin
regarding the differences of the Dexos oils.
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate...
Read full bulletin
unwanted odors in vehicles and which products to use for each application.
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
This informational bulletin provides information to dealership personnel on properly maintaining vehicles in dealer...
Read full bulletin
inventory.
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE...
Read full bulletin
for vehicles that may need an upgrade.
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that...
Read full bulletin
may be un necessary.
This informational bulletin provides tips on how to care for the interior of the vehicle using products.
This informational bulletin helps the technician quick reference repairs to bulletins as opposed to replacing parts that...
Read full bulletin
may be un necessary.
This information bulletin provides the technician the information on how to properly clean a metal surface using the...
Read full bulletin
correct tool.
This informational bulletin provides information on what products GM has to aid in the eliminating unwanted odors in a...
Read full bulletin
vehicle.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides information on how to use floor mats.
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This informational bulletin explains the Road Force balancers and what they can do for customer concerns.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance...
Read full bulletin
Claim (PAC) within the Courtesy Transportation Assistance Program.
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known...
Read full bulletin
as a Product Allegation Resolution (PAR) claim.
This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate...
Read full bulletin
unwanted odors in vehicles and which products to use for each application.
This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in...
Read full bulletin
vehicles.
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended...
Read full bulletin
Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
This informational bulletin provides information for technicians on the reuse of fasteners and the proper reading of...
Read full bulletin
torque specifications.
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
This informational bulletin provides information on a GM of Canada OnStar cellular communication upgrade.
This informational bulletin adds the 2014 and 2015 model years to information of a language change for OnStar System (U.S.
Read full bulletin
and Canada only).
This informational bulletin provides information on the PQC assembly replacement process - for dealers required to...
Read full bulletin
contact PQC prior to replacing an assembly (U.S. and Canada only).
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications...
Read full bulletin
to Control GM Accessory Remote Start Kits.
This informational bulletin provides information to the dealers on properly maintaining vehicles in inventory.
This informational bulletin is to assist with the identification of issues that are not considered warrantable.
This information bulletin provides the technician with additional information on fixing the vehicle right the first time...
Read full bulletin
by listing possible concerns to specific vehicles.
This technical bulletin provides a revision for 03-00-89-0061I to add the 2014 model year and Transport Mode heading.
This technical bulletin provides a revision of 05-09-40-002F to add the 2013-2014 model years.
This informational bulletin provides information for dealers to properly maintain vehicle in inventory.
This informational bulletin provides information on the proper cleaning products for GM hard or plastic surfaces, seats...
Read full bulletin
carpet, vinyl.
This technical bulletin provides a procedure on aftermarket ALSL or DLC devices causing multiple issues due to suspected...
Read full bulletin
tampering.
This informational bulletin provides information on fix it right for first time issues.
This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible...
Read full bulletin
condition and add a Note in the Instructions section.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on the replacement process for the product quality center.
This technical bulletin provides a procedure on suspected tampering due to aftermarket ALDL or DLC interface devices...
Read full bulletin
causing multiple issues.
This informational bulletin provides directions on submitting different PIRs
This preliminary information bulletin provides a revision of PI0291 to add 2012 model year.
This technical bulletin provides a revision of 11-08-49-001E to add the 2014 model year.
This technical bulletin provides a revision of 99-04-20-002G to add 2013-2014 model years.
This preliminary information bulletin is for information on COAX Repair Kit Availability.
Read full bulletin
Revised from PI0572A
This preliminary information bulletin provides information on poor or no transmitter range when using the remote keyless...
Read full bulletin
entry (RKE) and/or remote vehicle start (RVS).
This informational bulletin provides information for the PQC assembly replacement process.
Pre-Delivery & Maintenance
135 bulletinsThis bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
Vehicle Recalls
Vehicle Recalls
Learning Issues When Repairing Service Stability/Traction Message.
Learning Issues When Repairing Service Stability/Traction Message.
Ground Effects - Service Fix For Gapping At Corners Only.
Service Stability Message With Code U0710
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on proper use of floor mats.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and...
Read full bulletin
PF48.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Preliminary Information communication provides information to aid the technician in completing the various recalls...
Read full bulletin
/ service procedures related to key and transmitter programming.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398,...
Read full bulletin
E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This warranty administration bulletin provides policy information on required operating procedures.
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the...
Read full bulletin
requirements for the dealer to comply.
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S.
Read full bulletin
and Canada dealers only.
This warranty administration bulletin provide policy information on required operating procedures.
This warranty administration bulletin adds 2012 - 2015 model years to information communicating a change in the product...
Read full bulletin
field action customer reimbursement procedure (U.S. Dealers Only).
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is...
Read full bulletin
considered warranty and non-warranty.
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information on required operating procedures.
This informational bulletin provides information for Warranty Administration ? Changes in Powertrain Warranty Coverage ...
Read full bulletin
Effective with 2010 Model Year.
This informational bulletin provides a revision for 07-03-10-015B to add the 2013-2014 model years and remove the Saab...
Read full bulletin
Warranty Information.
This preliminary informational bulletin provides a revision of PI0388B to add the Cadillac XTS model, graphics, improved...
Read full bulletin
Instructions and Warranty Information.
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is...
Read full bulletin
considered warranty and non-warranty.
This preliminary informational bulletin provides service information to the dealer technicians that the remote start...
Read full bulletin
will not work with the ONSTAR REMOTE Link applcation
This warranty administration bulletin provides information on the Clarification of Use for Dealer Empowerment Labor...
Read full bulletin
Operations and Customer Enthusiasm
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so...
Read full bulletin
that vehicles can be fixed right the first time in for service.
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that...
Read full bulletin
was at fault of the cutomer and how to properly claim them on the warranty paperwork
This informational bulletin provides dealership personnel with information on new vehicle Pre-Delivery Inspection (PDI)...
Read full bulletin
process and to encourage delivering quality vehicles and generating higher CSi scores.
This warranty administration bulletin provides policy information with the field action courtesy transportation policy.
This information for Warranty administration - Changes the Service Policy and Procedures Section 1.6.2.11 and list the...
Read full bulletin
requirements for the dealer to comply.
This Informational bulletin explains the warranty and policy exchange program for electronic devices and products, what...
Read full bulletin
can be approved by TAC and where the electronic parts can be returned to.
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is...
Read full bulletin
acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
This warranty administration bulletin provides information on GM?s policy for comprehensive courtesy transportation to...
Read full bulletin
its customers.
This warranty administration bulletin provide policy information of the JOB CARD, for a repair on vehicles and what is...
Read full bulletin
acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.
This warranty administration bulletin provide policy information on the change in product field action customer...
Read full bulletin
reimbursement procedure.
This warranty administration bulletin provide policy information on required operating procedures.
The purpose of this Preliminary Information is to provide tips and aid the dealership technicians in retaining the...
Read full bulletin
folding top in the side rails after either side rail or the canvas top has been replaced for service.
This informational bulletin provides a list of newly released PI and Bulletins in regards to recent released vehicles so...
Read full bulletin
that vehicles can be fixed right the first time in for service.
This warranty administration bulletin provides information on what should be considerd warranty damage or damage that...
Read full bulletin
was at fault of the cutomer and how to properly claim them on the warranty paperwork
This informational bulletin provides information on the Product Quality Center (PQC) assembly replacement process for...
Read full bulletin
Service Agents not required to contact PQC prior to assembly replacement.
This warranty administration bulletin provides retail and wholesale service personnel with the policies and the...
Read full bulletin
warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty administration bulletin provide policy information on required operating procedures.
This warranty administration bulletin provide policy information on clarification of use-dealer empowerment labor...
Read full bulletin
operations and customer enthusiasm.
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential...
Read full bulletin
tools that include consumable parts (U.S. Only).
This technical bulletin provides Warranty Administration - New Labor Codes information.
Electrical
98 bulletinsThis Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This Preliminary Information communication provides information to the technician about to install steering wheel...
Read full bulletin
mounted audio controls on a vehicle that was not originally built with that option. It is possible to install audio Steering Wheel Controls at the customer's expense. Technician will also need to reprogram the Body Control Module by contacting Techline Customer Support Center.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Loss of Air Conditioning - Reprogram Body Control Module
High Voltage Safety ? High Voltage Disabling
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
Ignition Key
Ignition Key
Intermittent No Crank When Ignition Key Is Turned To The Crank.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Programming And Activation Of Replacement OnStar Modules.
Intermittent No Crank No Communication To High Speed LAN Modules.
GM Wiring Repair Strategy Information
Information on Counterfeit Airbag Modules
Loss of Air Conditioning - Reprogram Body Control Module
OnStar Module Does Not Support All B101D Symptom Codes.
Generation 9 OnStar Modules Inoperative, Bluetooth Inoperative and Possible Battery Discharge Condition (Replace OnStar...
Read full bulletin
VCIM)
Accessory Power Outlet and Trailer Lighting Fuse Replacement Labor Operation N1720 Fuse Replacement
Information on Counterfeit Airbag Modules
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
Intermittent No Crank When Ignition Key Is Turned To The Crank.
SPL Parts, Inc. manufacturers and distributes aftermarket lower control arms for dedicated competition vehicles and...
Read full bulletin
"track day" cars some of which may be used on both track and highway. SB 23-01 adresses proper installation torque of cap bolt fasteners attaching SPL's aftermarket lower control arms, recurring inspection and confirmation of torque setting and removal and replacement of damaged or under torqued fasteners to reduce risk of premature failure and accident. SB-23-01 was mailed, emailed and posted on SPL website to known resellers, race teams and users of the affected parts and is being submitted here as required by part 579.5. Vehicle Applications include: BMW series 1,2,3,& 4, 2008-2023; Chevrolet Camaro 26-2023, Cadillac ATS, CTS 2016-2019; Ford Mustang 2015-2023; Toyota Supra 2020-2023.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information.
This service bulletin provides information on Module Harvesting.
This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a...
Read full bulletin
condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1.
Read full bulletin
IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2 The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple...
Read full bulletin
keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple...
Read full bulletin
keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin explains to the technician that when using wiring repair labor operations,...
Read full bulletin
additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
This informational bulletin provides information on key code security rules and information on GM keycode look-up...
Read full bulletin
applications.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part...
Read full bulletin
Number in eSI and how to locate the part(s) in the EPC.
This informational bulletin provides information on how to determine whether or not an airbag module is counterfeit or...
Read full bulletin
not and what to do if a counterfeit airbag is found.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive...
Read full bulletin
finish".
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This informational bulletin updates information on electrical ground repairs using new replacement fasteners with...
Read full bulletin
conductive finish.
This informational bulletin provides information on control module diagnostics and configuration, programming using...
Read full bulletin
the TIS Service Programming System (SPS), set-up and warranty.
This warranty administration bulletin provides policy information on ACDelco replacement battery warranty procedures.
This Preliminary Information communication provides information to the technician about vehicles that the radio can be...
Read full bulletin
turned on after turning the ignition off and opening the driver?s door. The radio can then be turned back on after the vehicle's Retained Accessory Power has been canceled by simply pressing the power button on the radio. This is a normal characteristic of the key off operation.
This Preliminary Information communication provides information to the technician with power folding top diagnostic tips.
Read full bulletin
Tech should review the last Preliminary Information per the customers concern. The list of Bulletins are 12052: Customer Satisfaction - Convertible Top Enhancements and 13113: Service Update for Inventory and Customer Vehicles - Convertible Top Cosmetic Blemish - Expires with Base Warranty. The list of Preliminary Information are PI0351: Folding Top Tonneau Cover - Installation of Body Side Lower Trim Panel Spacer During Pre-Delivery Inspection, PI0378: Information on Convertible Top Operation Below 0 C (32F) in Snow, Rain or After Wet Conditions - Ice Formation in Water Management Bag, PI0379: Information on Location of Convertible Specific Manual Trunk Release, PI0397: Water Leak in Rear Compartment/Trunk - Convertible Top Water Management Bag Repair, PI0406: General Guidelines for Inspection of Convertible Water Management Bag Anytime Folding Top is Removed, PI0424: Rattle, Creak or Popping Noise in Rear Floor Area, PI0449: Rattle from Rear Compartment Area when Driving with Convertible Top in Closed (Up) Position, PI0509: Convertible Top Will Not Open/Retract, Clear Top Storage Area Message Displayed in Driver Information Center, PI0520: Top Not Secure Message Displayed in Driver Information Center, PI0525: Folding Top Striker Assembly Plastic Insert Loose/Missing, PI0625: Hydraulic Pump Leaking Fluid in Area of Rear Seat, Floor or Trunk, Convertible Top Inoperative or Noise, PI0756: Retrofit Procedure for New Corded Folding Top Cover Installation to Original Design Frame, PI0997: Convertible Top Difficult to Latch Closed, PIC5449: Convertible Roof Cloth Sags At Rear/Large Gap Between Number 5 Bow And Rear Panel, PIC5458: Water Leak In Rear Floor Area, PIC5527: Headliner Trim Cloth Pulls Loose From Rear Window Retainer, PIC5553: Creak Or Squeak Noise From Rear Of Folding Top, PIC5605: Folding Top Pulls Loose From Rear Side Rail, PIC560
This informational bulletin provides information that may be useful in diagnosing/testing batteries that have set for a...
Read full bulletin
long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.
This preliminary informational bulletin provides information that the tire pressure monitor (TPM) sensors must always...
Read full bulletin
be re-learned when accessory wheels are installed on the vehicle.
This informational bulletin provides information for Transport Mode On Message Displayed in Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing (Follow Procedure as Outlined Below) Condition.
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if...
Read full bulletin
it is warranty or not.
This warranty administration bulletin provides policy information on ACDelco replacement battery warranty procedures.
This preliminary informational bulletin provides repair information to correct a customer concern of "Top Not Secure"...
Read full bulletin
message displayed in the DIC, even when driving and the folding top is closed/secure.
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code...
Read full bulletin
E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and...
Read full bulletin
reprogram modules.
This informational bulletin provides information to dealership personnel regarding warranty codes generated by EL-50313...
Read full bulletin
Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if...
Read full bulletin
it is warranty or not.
Tthis preliminary bulletin provides a procedure to reposition the subwoofer speaker wiring away from the cone to correct...
Read full bulletin
the customers concern of a buzz/rattle from the rear speaker area.
This informational bulletin explains if the fuse is open when the customer plugs in the trailer, that it may be the...
Read full bulletin
cause if diagnostics finds no problems to that point.
This warranty bulletin explains how to use the EL-50313 Midtronic GR8 Battery tester to test a battery and determin if...
Read full bulletin
it is warranty or not
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED,...
Read full bulletin
No WiFi Operation, and/or Limited OnStar Module Functionality After OnStar Module Replacement for Another Condition.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel...
Read full bulletin
revised wiring repair labor operations and required additional information.
This informational bulletin communicates GM wiring repair strategy information.
Battery Testing and Warranty Replacement Requirements (North America ONLY)
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This informational bulletin explains how to cut a new key or how to get a precut key from GM.
This informational bulletin provides information accessory power outlet and trailer lighting fuse replacement due to...
Read full bulletin
electrical systems that can be affected by devices that are plugged in by the customer.
The information in this bulletin details the proper configurations for the ignition key, fob, key tags, key rings, key...
Read full bulletin
ring sizes and applying a QR code sticker or barcode sticker to a key fob.
This informational bulletin provides information on suspected tampering on vehicles modifications for identifying non GM...
Read full bulletin
ECM calibrations.
This technical bulletin provides a procedure to turn the transport mode on/off message that is displayed in the DIC...
Read full bulletin
and/or battery light is flashing.
This technical bulletin provides a procedure to turn the transport mode on/off message that is displayed in the DIC...
Read full bulletin
and/or battery light is flashing.
This preliminary informational bulletin provides information on communication interface module replacement.
This informational bulletin provides information for warranty codes that are generated by EL-50313 midtronics GR8...
Read full bulletin
battery tester/charger.
This informational bulletin provides information on key codes security rules and information on GM key code look up...
Read full bulletin
application.
This informational bulletin provides information for GM wiring repair.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
Body & Paint
57 bulletinsThis PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
Water Leak in Rear Compartment/Trunk ? Convertible.
Rear and Side Tempered Glass Spots.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
A Door May Not Open With The Outside Handle And/Or The Inside Handle.
Water Leak In Rear Floor Area.
Water Leak In Rear Floor Area.
Convertible Roof Cloth Sags At Rear / Large Gap Between Number 5 Bow And Rear Panel.
Driver/Passenger Door and/or IP Accent Lighting ? Light Bar (Pipe) Inoperative or Loses Intensity
A Door May Not Open With The Outside Handle And/Or The Inside Handle.
This service bulletin provides information for dealers/technicians on diagnosing and repairing a side window glass not...
Read full bulletin
clearing the molding when indexing down during door opening.
This service bulletin provides information on Paintless Dent Repair Process.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint...
Read full bulletin
percentage.
This service bulletin provides information for dealers/technicians on diagnosing and repairing a side window glass not...
Read full bulletin
clearing the molding when indexing down during door opening.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This PI was created to address XM signal performance with the sunroof open and covering the antenna.
This Preliminary Information communication provides information to the technician about vehicles that have a ticking...
Read full bulletin
noise on cold start after sitting more than 6 hours. Technician will inspect the oil pump pick-up tube to block seal being compressed. It the seal is compressed replace the seal and retest.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This informational bulletin provides information to correct a dealer concern of what they perceive to be paint staining...
Read full bulletin
when the protective shipping film is removed from certain vehicles.
This informational bulletin provides information on chemical staining, pitting, corrosion and/or spotted appearance of...
Read full bulletin
chromed aluminum wheels, along with warranty information regarding these conditions.
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving...
Read full bulletin
Speeds
The informational bulletin provides a procedure to remove and repair rust from a Hem Flange.
This warranty administration bulletion provides the dealer technician information and guidelines for claiming a...
Read full bulletin
windshield.
This preliminary information bulletin provides information the proper ways of adjusting the center trim bezel to correct...
Read full bulletin
the condition of the CD/DVD will not eject from the instrument panel mounted player.
This informational bulletin provides recommendations and product information for application of anti-corrosion materials
This informational bulletin provides dealership personnel with information on interior cleaning of Instrument Panel...
Read full bulletin
(IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.
This informational bulletin provides explanation on using the tire sealent in the GM kit as a temporary fix only untill...
Read full bulletin
the tire can be properly repaired under the new tire warranty.
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal...
Read full bulletin
characteristic.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin provides information for dealers/technicians on diagnosing and repairing a side window glass...
Read full bulletin
not clearing the molding when indexing down during door opening.
This preliminary information bulletin provides a procedure on a water-test repair for the convertible top to eliminate a...
Read full bulletin
water leak in the rear compartment/trunk.
This informational bulletin provides information on the appearance of chromed aluminum wheels due to chemical staining,...
Read full bulletin
pitting corrosion and/or spotted.
This informational bulletin provides information pre-painting/cleaning process for TPO plastic fascias.
This preliminary bulletin explains the marks in the glass are normal when wearing polarized sunglasses and do not...
Read full bulletin
replace any glass for this reason.
Hydraulic Pump Leaking fluid in area of rear seat, floor or trunk, Convertible Top Inoperative or Noise
This preliminary informational bulletin provides a procedure to replace the sunroof locking slide guides for "Sunroof...
Read full bulletin
will not open/close or is noisy during operation" Condition.
This informational bulletin provides information on the door and quarter panel paint appearance.
This Preliminary Information communication provides information to the technician on a proper paint code for some hard...
Read full bulletin
to find color options.
Fuel System
44 bulletinsThis service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
Navigation Radio Radio And Integrated Center Stack
Performance Exhaust Part Number When Used With Accessory Ground Effects.
Navigation Radio Radio And Integrated Center Stack
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable...
Read full bulletin
diesel fuel.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks...
Read full bulletin
using the evaporative emission cart smoke machine and ultrasonic leak detectortools.
This informational bulletin provides information on top tier fuels and what brands are available.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
This informational bulletin provides information on top tier fuels and what brands are available.
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if...
Read full bulletin
debris have entered the exhaust system.
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER...
Read full bulletin
Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
This informational bulletin provides a revision 11-00-90-001A to add the 2014 model year.
Read full bulletin
Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.
This technical bulletin provides repair information to correct a customer concern of the transmitter/FOB appearance...
Read full bulletin
after integrated blade removed.
This informational bulletin provides information on TOP TIER Detergent Gasoline and available retail brands.
This technical bulletin provides repair information to correct a customer concern of the transmitter/FOB appearance...
Read full bulletin
after integrated blade removed.
This informational bulletin provides information on new fuel tank, filler pipe and CCM reprogramming that is required if...
Read full bulletin
the fuel tank is being replaced for service.
This informational bulletin provides the technician with information on what E85 fuel may due to a non E85 vehicle.
This informational bulletin provides information on top tier fuels and what brands are available.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This informational bulletin provides information on how to save fuel and proper maintenance without using fuel or oil...
Read full bulletin
additives.
Tires & Wheels
41 bulletinsThis service bulletin provides information on Tire Sidewall Irregularities.
This service bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left or...
Read full bulletin
Right, Wanders, Follows Depressions in Road Surface, Tramlining.
Information on Tire Rotation Recommendations.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
Information on Removal/Cracking of Stainless Steel Wheel Nut Caps.
Questions On Swapping Wheels From One Vehicle To Another.
Questions On Swapping Wheels From One Vehicle To Another.
This service bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left or...
Read full bulletin
Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance,...
Read full bulletin
Shake, Flat Spotting) of GM Original Equipment Tires.
This informational bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left...
Read full bulletin
or Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This informational bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left...
Read full bulletin
or Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This informational bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left...
Read full bulletin
or Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
This informational bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left...
Read full bulletin
or Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This informational bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left...
Read full bulletin
or Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to...
Read full bulletin
possible chances of the customers concerns over tire vibration are repair.
This informational bulletin provides the technician with information on tire radial force variations and how to use it.
This informational bulletin provides the technician the proper way to install and torque the wheel.
This informational bulletin explains how to balance a chrome wheel without damaging the chrome face of the rim.
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to...
Read full bulletin
possible chances of the customers concerns over tire vibration are repair.
This technical bulletin provides a procedure on cleaning a leaking rim, to correct a customers concern of having a slow...
Read full bulletin
tire leak and low tire psi message on.
This informational bulletin explains the use of Nitrogen in GM tires.
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to...
Read full bulletin
possible chances of the customers concerns over tire vibration are repair.
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques...
Read full bulletin
used to install wheels onto vehicles
This informational bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left...
Read full bulletin
or Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This informational bulletin explains a normal condition of new tires may shake and vibrate for the first few miles.
This informational bulletin provides the technician with information on tire radial force variations and how to balance...
Read full bulletin
a tire using the balancer.
This informational bulletin provides technicians with ways to decrease the tire slipping on the rim and reduce to...
Read full bulletin
possible chances of the customers concerns over tire vibration are repair.
This informational bulletin provides a description of the proper wheel installation and proper wheel torque techniques...
Read full bulletin
used to install wheels onto vehicles
This informational bulletin provides additional information to the technician on how to check for Tire Radial Force...
Read full bulletin
Variations and the difference between balancing a flange and flangeless rim.
This informational bulletin provides information on tire radial force variation.
Transmission
37 bulletinsThe service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
Diagnostic Information for Transmission.
Intermittent Clutch Pedal Low Or Sticks To The Floor.
This bulletin advises the technician that the 6L50 (MYB), 6L80 (MYC) and 6L90 (MYD) Transmission Oil Filter and Seal Kit...
Read full bulletin
part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold individually.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
Warranty Administration ? Change in Automatic Transmission Add Condition Documentation and Claim Submission
this service bulletin advises the technician to replace the transmission and not overhaul it to correct a customer...
Read full bulletin
concern of Manual Transmission Pops/Jumps Out of Third Gear After Shifting and During Acceleration.
this service bulletin advises the technician to replace the transmission and not overhaul it to correct a customer...
Read full bulletin
concern of Manual Transmission Pops/Jumps Out of Third Gear After Shifting and During Acceleration.
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare...
Read full bulletin
after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This informational bulletin explains how the trans slip or flare can be a normal condition.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This Preliminary Information communication advises the technician that the customer may experience a 2-3 slip or flare...
Read full bulletin
after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a...
Read full bulletin
customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This informational bulletin provides normal operating characteristics and diagnostic information on Manual...
Read full bulletin
transmissions.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This informational bulletin provides information for Automatic Transmission Oil Cooler Flow Test Essential Tool J-45096...
Read full bulletin
TransFlow.
This preliminary informational bulletin provides a procedure to inspect the transmissions filter for splits or cracks to...
Read full bulletin
correct the customers concern for no forward, reverse or slips.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
This informational bulletin provides technicians with information to assist in identifying operating characteristics of...
Read full bulletin
manual transmissions that repair attempts will not change.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This information was created to inform the technician that the 2-3 upshift and the 3-2 downshift clunk is caused by the...
Read full bulletin
releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a...
Read full bulletin
customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
Software & Calibration
36 bulletinsVehicle Software Enhancements
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
OnStar Voice Fallback Number Update
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This preliminary informational bulletin provides a revision for PI0011C to add the 2013-2014 model years and update...
Read full bulletin
Warranty Information.
This informational bulletin provides a revision for 09-00-89-008 to add model years, update the Labor Operation...
Read full bulletin
Information and Transaction Submissions Procedure and general content updates.
This informational bulletin provides a revision for 05-08-48-001B to add 2010-2014 model years and update Labor...
Read full bulletin
Operation.
This informational bulletin provides a revision for 13-00-89-004A to include updated information.
This informational bulletin provides a revision for 05-03-07-009E to add the 2014 model year and update the Labor...
Read full bulletin
Operations.
This informational bulletin provides a revision for 10-00-89-016 to include the 2012-2014 model years and update the...
Read full bulletin
Labor Operation graphic.
This informational bulletin provides a revision for 06-00-89-026J to add the 2014 model year and update the labor...
Read full bulletin
operations.
This preliminary informational bulletin provides a revision of PI0785A to add the 2014 model year, include Encore model...
Read full bulletin
and update the Parts and Warranty Information.
This informational bulletin provides a revision for 09-03-16-002A to add model years, add the current Global Labor Time...
Read full bulletin
Code and update the tool reference information.
This informational bulletin provides a revision for 09-07-30-018C to add the 2014 model year and update the Labor...
Read full bulletin
Operation.
This informational bulletin is a revision for 03-06-03-004G to add the 2014 model year and update the Labor Operation.
This informational bulletin is a revision for 11-00-89-007B to add the 2014 model year and update the Labor Operation...
Read full bulletin
List.
This informational bulletin is a revision for 07-00-89-037E to add the 2014 model year and to update the labor operation...
Read full bulletin
under Courtesy Transportation Warranty Transaction Submission.
This informational bulletin is a revision for 09-00-89-016B to add the 2014 model year and update the labor operation.
This informational bulletin provides a revision for 03-08-48-006I to add model years and update parts information.
This preliminary informational bulletin provides a revision of PI0360A to add the 2013-2014 model years and update the...
Read full bulletin
Recommendation /Instructions.
This preliminary informational bulletin is being revised to update the Parts Information for PI0807.
This preliminary informational bulletin is being revised to update the Parts Information for PI0807.
This preliminary informational bulletin provides a revision for PI0137C to add the 2013-2014 model years and update the...
Read full bulletin
Warranty Information.
This technical bulletin provides a revision for 04-00-89-015D to update content and incorporate the U.S.
Read full bulletin
version of Bulletin 12-00-89-003.
This technical service bulletin provides a revision for 07-08-49-020G to add the 2014 model year and update model list.
This informational bulletin provides technicians with updated information to help identify the differences between what...
Read full bulletin
is considered a fluid leak, and what is considered seepage.
This informational bulletin provides information on a update for the Electronic Component Exchange Program (U.S.
Read full bulletin
and Canada Only)
This preliminary information bulletin provides a revision of 13-00-89-004D to include updated information.
This informational bulletin is a revision of 10-06-01-008I to add the 2010-2012 Chevrolet Colorado and GMC Canyon, RPO...
Read full bulletin
LH9 and update the Labor Operation to the Global Labor Code (GLC).
This preliminary information bulletin provides a revision of PI0685A to remove the WPC information and update the Parts...
Read full bulletin
Information.
This technical bulletin provides a revision of 13-00-89-004 to update car issues information for reference...
Read full bulletin
information/bulletin PI0746C.
This technical bulletin provides a revision of 11-08-44-003 to update the Sample Customer Notification Letter.
This technical bulletin provides a revision of 03-06-03-003B to add the 2010-2014 model years, update the Attention...
Read full bulletin
statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).
This technical bulletin provides a revision of 10-00-89-017Z to include updated information.
Lighting
32 bulletinsThis informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
GM Accessory and Camaro Transformer High Wing Spoiler Center High Mount Stop lamp.
GM Accessory and Camaro Transformer High Wing Spoiler Center High Mount Stop lamp.
SES Light Rough Running And/Or Lack Of Power.
SES Light Rough Running And/Or Lack Of Power.
SES Light Rough Running And/Or Lack Of Power.
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
Fog Lamp Operation or Adding / Enabling Fog Lamps On a Vehicle Not Originally Equipped with Fog Lamps.
Fog Lamp Operation or Adding / Enabling Fog Lamps On a Vehicle Not Originally Equipped with Fog Lamps.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and...
Read full bulletin
the Proper use of GM Simplified Maintenance Schedules.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This preliminary informational bulletin provides repair information to correct a customer concern of slow loss of tire...
Read full bulletin
pressure and/or low tire pressure indicator/warning lamp on after sustained high speeds.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This bulletin provides information regarding the normal tire wear condition of slight or mild tire feathering and...
Read full bulletin
recommended practices.
This preliminary information bulletin provides a descritption of operation of the echo control and noise cancellation...
Read full bulletin
settings for concernc regarding noice drop outs during calls and muffled sound.
This informational bulletin was created to inform that any accessories that are install from the GM factory will be...
Read full bulletin
covered under the standard vehicle warranty and dealer installed accessories will be cover for a full year (12months).
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be...
Read full bulletin
covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
This informational bulletin provides dealership personnel information on unscheduled supplemental services (including...
Read full bulletin
flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).
This Preliminary Information communication provides information to the technician about vehicles that show an error...
Read full bulletin
message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement.
This technical bulletin provides information on Vehicle Software Enhancements for 2014 and prior GM Passenger Cars and...
Read full bulletin
Light Duty Trucks.
Infotainment
26 bulletinsXM Audio Traffic And Travel Link Availability And Operation.
Information On Requests To Add OnStar Bluetooth Option.
Checking Smartphone Bluetooth Software Update Status
Checking Smartphone Bluetooth Software Update Status
Service Stabilitrak Message Displayed At Startup
Service Stabilitrak Message Displayed At Startup
Service Stabilitrak Message Displayed At Startup
Key Off Radio Operation.
Key Off Radio Operation.
This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After...
Read full bulletin
an OnStar In-Vehicle Voice Message Is Heard.
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a...
Read full bulletin
feedback form to the GM navigation disc center website.
This Preliminary Information communication provides information to the technician about vehicles that may have an issue...
Read full bulletin
when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a...
Read full bulletin
feedback form to the GM navigation disc center website.
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions...
Read full bulletin
and to correct the customers concern of the radio being loud during navigation.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a...
Read full bulletin
condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This preliminary informational bulletin provides information onUnexpected Loss of Radio Audio (Radio Goes Silent/No...
Read full bulletin
Sound) and Other Blackberry Phone - Bluetooth Issues Concern.
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions...
Read full bulletin
and to correct the customers concern of the radio being loud during navigation.
This Technical bulletin provides a procedure to request a hard mute from Onstar when navigation is annoucing directions...
Read full bulletin
and to correct the customers concern of the radio being loud during navigation.
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a...
Read full bulletin
feedback form to the GM navigation disc center website.
This Preliminary Information communication provides information to the technician about vehicles that are travelling from Canada to the United States.
Read full bulletin
While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a...
Read full bulletin
condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc...
Read full bulletin
information.
This preliminary bulletin explains physical damage to radios and IPCs must be reviewed and validated if covered under GM...
Read full bulletin
warranty or not.
This preliminary bulletin provides information on Radio Favorites Disappear, HD Audio Concerns Favorites Disappear, HD...
Read full bulletin
Audio.
This preliminary information bulletin provides information on inaccurate or slow response of outside air temperature...
Read full bulletin
display.
This technical bulletin provides a procedure to remove the transport mode on message displayed in the DIC.
Brakes
21 bulletinsThis bulletin provides information on possible normal brake drag caused by the vehicle parked for an extended period of...
Read full bulletin
time.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
Front Or Rear Brake Noise On Slow Stops.
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
EBCM Wheel Speed Sensor Diagnostic Aid for ABS Message
Excessive Brake Dust On Wheels.
Excessive Brake Dust On Wheels.
This bulletin provides information on possible normal brake drag caused by the vehicle parked for an extended period of...
Read full bulletin
time.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This bulletin provides information on possible normal brake drag caused by the vehicle parked for an extended period of...
Read full bulletin
time.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This bulletin provides information on possible normal brake drag caused by the vehicle parked for an extended period of...
Read full bulletin
time.
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly...
Read full bulletin
abrasive disk on gasket sealing surfaces or reused parts.
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk...
Read full bulletin
on gasket sealing surfaces or reused parts.
This informational bulletin provides information for Disc Brake Warranty Service and Procedures.
This bulletin provides information on possible normal brake drag caused by sitting.
This informational bulletin provides technicians with a brake lathe calibration procedure.
This preliminary information bulletin provides information for the brake caliper finish removal, degradation or staining...
Read full bulletin
from wheel cleaning chemicals.
HVAC & Climate
13 bulletinsA/C Blows Warm Or Poor Performance.
Radio Display Fogs Up When Using Air Conditioning.
Radio Display Fogs Up When Using Air Conditioning.
This Preliminary Information communicates to the technician the various repair procedures that are needed forvehicles...
Read full bulletin
that have a repeat poor performance of the air conditioning system / AC compressor replacement.
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS)...
Read full bulletin
concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
This technical bulletin provides repair information for the correction of a customer concern of short duration musty...
Read full bulletin
odors emitted from the HVAC system at vehicle start-up in hot, humid conditions.
This technical bulletin provides a procedure to correct the customers concern of odor coming from the Air conditioning.
This preliminary informational bulletin provides technicians with diagnostic tips for a customer concern of odor...
Read full bulletin
emanating from HVAC system.
Steering
3 bulletinsAdding Radio Steering Wheel Control Switch.
This technical bulletin provides a procedure to eliminate a power steering noise due to extremely low temperatures.
This preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid...
Read full bulletin
reservoir.
Suspension
3 bulletinsThis preliminary bulletin provides information on a possible normal front end noise if the suspension has been...
Read full bulletin
confirmed to be in working order.
This preliminary bulletin provides information on a possible normal front end noise if the suspension has been...
Read full bulletin
confirmed to be in working order.
This preliminary bulletin provides information on a possible normal front end noise if the suspension has been...
Read full bulletin
confirmed to be in working order.
Air Bags & Safety
2 bulletinsThis service bulletin provides information on availability for a seat belt extender.
This preliminary informational bulletin provides information on the driver airbag light is flashing in the cluster...
Read full bulletin
and/or the passenger airbag ON indicator does not illuminate when the passenger is present when the SDM setup has not been completed after reprogramming.
Hybrid & EV
1 bulletinThis technical bulletin provides a revision for 09-00-89-029J to add the 2014 model year and to add the Impala, Spark,...
Read full bulletin
Spark EV, Silverado and Sierra.