2015 Can-Am Spyder F3 TSBs
27 Technical Service Bulletins across 9 categories
Categories
Other
8 bulletinsThe front sprocket might be stuck on the mainshaft upon disassembly
Oil pressure switch switch connector boot cracking.
Up-to-date technical information on the 2015 roadster product.
Up-to-date information on the 2015 Roadster product.
Revision 1 of Bulletin 2016-4 The pillion switch is not activated when a passenger is on the seat.
Read full bulletin
This situation may results in a loss of control and possibly cause injuries or even death.
BRP has surveyed a few clients and has received the comment of vibration felt at certain speeds and RPM.
Read full bulletin
It was determined that the belt was the culprite of the vibration. BRP wants to gather new information of this complaint for this year so information is given to open a BOSSWeb case if complaint is received.
POSTING ABOUT NEW BULLETIN 2016-3 -SOME THROTTLE GRIPS ASSEMBLY MAY HAVE TIGHTER MATERIALS TOLERANCES THAT MAY INCREASE...
Read full bulletin
RETURN TIME TO ORIGINAL POSITION
PRODUCT REFERENCE ARTICLE - CONDITIONS, CAUSES AND CURES DESCRIBED ARE FOR INDIVIDUAL CASES AND DO NOT IMPLY ALL MY...
Read full bulletin
UNITS ARE AFFECTED NOR PARTS BE REPLACED WITHOUT PROPER DIAGNOSTIC PROCEDURES.
Engine
7 bulletinsRevision of TST 140875 P0730 Active Fault Fault code can be triggered if the unit has the wrong rear sprocket or a different wheel size.
Read full bulletin
The cluster will stop displaying the gear indication and check engine light came on (limp home condition) and the gearbox won't shift.
Engine Oil Level reading Issue Impossible to read the oil level on the dipstick.
Spyder P0730 Active Fault - This fault code can be triggered if the unit has the wrong rear sprocket or a different wheel size.
Read full bulletin
The cluster will stop displaying the gear indication and check engine light came on (limp home condition) and the gearbox won't shift.
Missing or damaged scavenge pump components could lead to poor engine performance on 1330 engines.
Rear Brake Hose Might Be in Contact with Muffler Support or Pin on Tandem Master Cylinder.
Warranty bulletin 2015-4 The knock sensor harness may melt if routed too close of the exhaust manifold heat shield.
Read full bulletin
A melted harness would lead to a limp home mode.
TECHNICAL SERVICE TIP (TST): THE ENGINE OIL PRESSURE SWITCH CONNECTOR PROTECTIVE BOOT MAY CRACK OR DEGRADE OVER TIME.
Read full bulletin
INFORMATION ON STEPS TO FOLLOW TO REPLACE THE BOOT WITH A MORE RESISTANT PART.
Transmission
5 bulletinsClutch assist installation.
Gear box position sensor contamination.
Gearbox position sensor contamination additional information.
Oil Sweating from SE6 Clutch Clover HCM Connector
THE ROUTING OF THE TRANSMISSION WIRING HARNESS MAY BE INCORRECT WHICH MAY PINCH THE HARNESS AND CAUSE ELECTRICAL...
Read full bulletin
PROBLEMS WITH THE TCM OR SHIFTING ISSUES. THE SOLUTION IS TO INSPECT THE TRANSMISSION WIRING HARNESS FOR PROPER ROUTING AND CORRECT AS NECESSARY. ONLY IF HARNESS HAS BEEN DAMAGE WILL REPLACEMENT HARNESS WILL BE REQUIRED.
Electrical
2 bulletinsTrailer module may fail.
Intermittently, the ignition key may not be recognized causing the unit not to start.
Tires & Wheels
1 bulletinFront Sprocket Wear- Interim Solution As covered in the SAFETY CAMPAIGN BULLETIN 2019-10, The front sprocket may be...
Read full bulletin
defective and may be subject to premature wear.
Pre-Delivery & Maintenance
1 bulletinSafety Campaign- Front Sprocket Wear- Potential Loss of Propulsion The front sprocket may be defective and may be subject to premature wear.
Read full bulletin
Over time, the vehicle could lose propulsion. If the vehicle loses propulsion, there is an increased risk of a crash.
Infotainment
1 bulletinIf a customer wants to change the radio pre-set channel number and is unable to do so, here is the reason this is...
Read full bulletin
happening.
Suspension
1 bulletinDetails on the f3 rear suspension and available options.
Body & Paint
1 bulletinHood stripe decals does not meet standards.