2019 Can-Am Ryker TSBs
25 Technical Service Bulletins across 9 categories
Categories
Electrical
5 bulletinsRYKER YAW Rate - SAS Sensor Faults These 3 faults (C0063 and/or C0051 and *C006C) can be triggered if the front...
Read full bulletin
suspension has excessive play or the front wheel alignment is out of specification
Yaw rate sensor faults might be triggered due to loose front suspension components.
This bulletin is the detailed repair procedure if the position light and flasher electrical harness in the front fenders...
Read full bulletin
have rubbed on the tires wearing the insulating sheath.
Warranty Bulletin no 2019-6 Speed Sensor Wiring Harness-Corrugated Tube Installation- Unregistered Vehicles Only.
Read full bulletin
The front speed sensor wiring harness could get pinched during the front fender installation
YAW rate sensor faults might be triggered due to loose front suspension components.
Fuel System
5 bulletinsFuel Pump can be noisy especially when low fuel levels and warm temperatures.
Ryker's fuel pump noisy when low fuel level and warm temperature
Revision of TST 137790 sent on June 2020.
Read full bulletin
Ryker Fuel Pump modification Part to install to reduce fuel pump noise
Part to install to reduce fuel pump noise
One or more wheel nuts may crack resulting in a reduced clamping force.
Read full bulletin
This could eventually affect the integrity of the wheel assembly and the vehicle's behavior. This may increase the risk of a crash.
Engine
3 bulletinsRykers 900 engines that may have the incorrect camshaft timing.
Read full bulletin
Ryker Equipped with the 900 engine may start well when cold but then can have a rough idle or even dies at idle when the engine is warmed up.
We have some report that some 602 and 903 engines have been produced with the wrong camshaft.
Read full bulletin
This document will help you to identify the correct one. If the wrong camshaft is installed the unit can have the following symptoms poor, idle, engine performance, O2 fault, engine misfire.
Possible contact between the exhaust pipe and frame.
Read full bulletin
Here are some ways to increase the distance between the exhaust pipe and the frame. The minimal distance between the exhaust pipe and the frame should be 5mm. Symptoms Excessive engine vibration felt, exhaust manifold bolts loose, engine rattle noise.
Brakes
3 bulletinsHandlebar may have a play in rotation due to unequal clamping surface Brake oil reservoir diaphragm may be incorrectly...
Read full bulletin
installed
Repair Procedure Revision- Brake Light Switch Adjustment Vehicle may indicate brake light switch failure, rear brake...
Read full bulletin
light stays ON or flashes intermittently.
Vehicle may indicate brake light switch failure.
Read full bulletin
One of the probable cause is the adjustment of the brake light switch/low pressure switch.
Other
2 bulletinsUpon installation of the 2-UP passenger seat, difficulty to install might result in the breakage of the latch.
This TST includes solution for the noise that can be heard or felt under deceleration at high speed.
Tires & Wheels
2 bulletinsMessage and alert to all dealer RYKER mandatory certification form The front wheel installation is a critical operation...
Read full bulletin
and must be performed as explained in the PDI bulletin.
Service Bulletin no 2019-3 On-Road Ryker- Importance of Wheel Installation Procedures
Pre-Delivery & Maintenance
2 bulletinsThis technical service tips is to show how to fix some leaks coming from the coolant cap area.
Warranty bulletin no: 2019-9 219400843 - Foldable Passenger Backrest - Pivot Attachment Missing Bolts
Transmission
2 bulletinsWarranty Bulletin no 2019-2 Revision 1 Oil Missing in the Gearbox
Warranty Bulletin no 2019-2 Oil Missing in the Gearbox
Lighting
1 bulletinSafety Campaign Revision- Wheel nut may crack.
Read full bulletin
One or more wheel nuts may crack resulting in a reduced clamping force. New VINs added in the warranty campaign and new steps in the procedure.