2007 Cadillac Xlr TSBs

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

GDS 2.

consumption.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

conductive finish.

conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

consumption.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

GDS 2.

consumption.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

issue.

issue.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

may have no Reverse and no 2nd gear.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

GDS 2.

Identification.

consumption.

engine is started while diagnosing for noise from the engine or transmission.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.

the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

engine oil consumption.

engine oil consumption.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

customer concerns related to wheel alignment.

correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

engine oil consumption.

transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.

for outer SMC skin separation from the magnesium frame.

Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact Partechand/orthe Techline Customer Support Center for additional support.

conductive finish.

transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

how toptier fuels should be used to reduce carbon build up.

bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.

skin separation from the magnesium frame.

Engineers by completely filling out requested reports.

Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.

skin separation from the magnesium frame.

General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

automatic transmission fluid pan hear with thethe key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

engine oil consumption.

when to replace a assembly as opposed to repairing and if an engine or transmission is being returned, that it has all the information in relation to that part being returned.

Engineers by completely filling out requested reports.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

how toptier fuels should be used to reduce carbon build up.

General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

on engine surfaces.

Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

(Aftermarket) engine and transmission calibrations for V6 and V8 gasoline engines Using Tech 2 or global diagnostic system 2 (GDS 2)

CNG, LPG or gasoline engine, transmission and/or transfer case.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.

directions may no longer be displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.

engine oil consumption.

for customer concerns related to wheel alignment.

damage.

Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.

a list of websites for additional information.

General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.

Engines Using Tech 2 or GDS 2

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

difficulty performing certain diagnostic procedures due to the ignition not being in the "Ignition On, Engine Off" mode. Technician will need to press and hold the ACC/OFF portion of the Start/ACC/OFF mode button for 5 seconds with a valid keyless entry transmitter inside the vehicle and the transmission in Park or Neutral.

OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.

receive OnStar Hands Free Calling calls and or the OnStar center is unable to perform remote services. Technician will need to push the OnStar Blue button and verify the system successfully connects to an advisor. Place an outbound personal call from the vehicle and verify it connects. Place an inbound call to the vehicle making sure to dial using the 11 digit phone number (1 + area code + number). If outbound calls can be placed and only incoming calls fail. Cycle power to the Vehicle Communication Interface Module and retest inbound call to the vehicle. If the power cycle corrects the concern and the module manufacturer is continental, replace the Vehicle Communication Interface Module. If the power cycle corrects the concern and the module manufacturer is LG, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance. If the concern is still present after the power cycle, please record information from the latest version of PIC4310 and call General Motors Technical Assistance Center for further assistance.

certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.

test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.

Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed.

various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will check Global Warranty Management system for customer satisfaction program 15086 status. If the status of the customer satisfaction program 15086 was not completed follow the steps to get the Telematics Communication Interface Control Module replaced. If the status of customer satisfaction program 15086 is found completed contact General Motors Technical Assistance Center OnStar group for further assistance.

Diagnostic Email report is inoperative. Please communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire.

severe internal engine damage.

concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

severe internal engine damage.

stuck after transmission service pump cover replacement.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.

one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.

Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

Technician should record module info per the latest version of PIC4310 and contact General Motors Technical Assistance Center.

Panel Cluster the exchange center is unable to program the actual mileage on the odometer or the actual mileage is unknown. Dealer will need to follow dealer to the General Motors service policies and procedures manual section 3.2.4 odometer servicing.

to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

rear composite springs cracked and/or broken. Technician should use only use J33432-A & J42188 are being used during installation. Technician should be advised that engineering has found that two chemicals, Phosphoric acid and Hydrofluoric acid that will damage the spring.

that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

Technician can check Service Information for some accessories. Technician can also contact Partech for assistance.

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

or engines during there break in period.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

to be abnormal may not have been there when the vehicle was purchased. Technician should look for Non - General Motors aftermarket accessories installed on the vehicle that can cause these issues.

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics. Technician may need to contact General Motors Technical Assistance Center depending on the STID, Station ID, or OnStar Customer Identifier.

Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.

that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.

Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.

INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED.

PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.

GENERAL MOTORS WILL ONLY SUPPORT A TIRE CALIBRATION FOR TIRES THAT HAVE BEEN SIZED, TESTED AND DESIGNED FOR THE VEHICLE IN QUESTION AND ITS APPLICATIONS. TECHNICIAN SHOULD NOT USE THE INFORMATION THAT IS PROVIDED BY THE ANTILOCK BRAKING SYSTEM TIRE SIZE SELECTION.

SYSTEM THAT HAS PROGRESSION TONES WHEN PRESSING THE BLUE OR RED BUTTON. TECHNICIAN WILL NEED TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER WITH THE SCAN TOOL DATA FROM THE ONSTAR SYSTEM.

GENERAL MOTORS AGAINST DEFECTS IN MATERIAL OR WORKMANSHIP UNDER THE BUMPER-TO-BUMPER NEW VEHICLE LIMITED WARRANTY.

A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL

TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.

DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.

ENGINE DAMAGE.

GASKET SEALING SURFACES.

AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.

A CUSTOMER MAY IDENTIFY A CONCERN OF UNABLE TO REACTIVATE A VEHICLE'S ONSTAR THAT HAS BEEN PREVIOUSLY DISABLED BY ONSTAR. DEALER IS TO CALL GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE IF THE CONCERN IS STILL PRESENT.

USAGE TO CORRECT A CONCERN THAT AFTER INSTALLATION OF A REPLACEMENT UPPER VALVE BODY, THE TRANSMISSION MAY HAVE NO REVERSE AND NO 2ND GEAR DUE TO THE INSTALLATION OF THE INCORRECT UPPER VALVE BODY.

COMPLAINT OF SES LIGHT BUT IT IS UNLIKELY THAT THERE WILL BE A COMPLAINT OF ANY ENGINE PERFORMANCE CONCERNS IF THIS APPLIES. UPON INSPECTION, DTCS P0171 AND P0174 WILL BE STORED AND FREEZE FRAME DATA WILL NORMALLY INDICATE THAT THEY SET AT APPROXIMATELY THE SAME TIME. THIS MAY BE THE RESULT OF A SMALL AIR LEAK IN THE AIR INDUCTION SYSTEM. *PE UPDATED 4/4/12. *PE

INFORMATION CENTER (DIC) WITH MULTIPLE ECM DTC'S P1516, P2101, P2119 OR P2176 (INSPECT THROTTLE BODY BLADE). *NJ

50 terminal test probe, replacement terminals, and terminated leads.

50 terminal test probe, replacement terminals, and terminated leads.

50 terminal test probe, replacement terminals, and terminated leads.

Allegation Resolution (PAR) claim.

Allegation Resolution (PAR) claim.

folding top.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Allegation Resolution (PAR) claim.

folding top.

Allegation Resolution (PAR) claim.

Only)

the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component

causing multiple customer concerns that do not have other diagnostic methods to identify them.

folding top.

Allegation Resolution (PAR) claim.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

higher CSi scores.

Dealers Only).

folding top.

Only).

verification sheets (CCVS).

for vehicles that may need an upgrade.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

higher CSi scores.

customer.

to complete some repairs.

verification sheets (CCVS).

A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

correct tool.

vehicle.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Customer Concern Verification Sheets (CCVS).

RemoteLink? phone application.

pictures.

appropriate Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

part numbers for the labels.

to complete some repairs.

additional information concerning Policy decision making.

Approved Refinish Materials booklet information.

may be un necessary.

correct tool.

vehicle.

regarding the differences of the Dexos oils.

for vehicles that may need an upgrade.

may be un necessary.

may be un necessary.

correct tool.

vehicle.

higher CSi scores.

components of the Remote Keyless Entry System.

higher CSi scores.

and Canada only).

by listing possible concerns to specific vehicles.

carpet, vinyl.

tampering.

condition and add a Note in the Instructions section.

causing multiple issues.

Revised from PI0572A

entry (RKE) and/or remote vehicle start (RVS).

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.

manually, to fix the customers concern of the mirriors shaking or fluttering at normal driving speeds.

customer.

unwanted odors in vehicles and which products to use for each application.

A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

verification sheets (CCVS).

part numbers for the labels.

first time.

Only)

Canada after Decommissioning of 2G CDMA Cellular Networks

and where to email the info to.

report.

after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.

A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.

connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.

CryoCobalt Drill bit.

may be un necessary.

after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.

regarding the differences of the Dexos oils.

find growing concerns around them.

and Canada only).

for causing multiple customer concerns that do not have other diagnostic methods to identify them.

Dealers Only).

considered a fluid leak, and what is considered seepage.

Tier 1 and Tier 2 empowerment tools: diagnostic fee, short term rental, and up-front towing (U.S. only).

of poor, limited, reduced Remote Keyless Entry (RKE) or Remote Vehicle Start (RVS) range.

remotelink phone applications

directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center.

Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.

system does not respond properly to some numbers and/or voice commands. Dealer should direct the customer to review the operational characteristics in the OnStar Users Guide.

customer may comment that when they travel to the United States, they are unable to connect to OnStar or use hands free calling. Dealer can advise the customer that the existing cell phone provider not having roaming agreements in areas outside of Canada. At this time, a customer has the option of contacting OnStar to have a 500 number loaded for OnStar operation while in the United States.

report.

TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.

THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.

*RM

*NJ

*KB

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.

as a discharged or disconnected battery, or if the vehicle is entered without the key fob or the fob is not working, the driver and passenger side doors can be opened from the inside of the vehicle by using the manual release levers located on the floor between the seats and the door openings.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

tried to provide a software update to the OnStar hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."

IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2 The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.

additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.

applications.

applications.

magnetically controlled suspension electrical connector not seated.

when replacing a module.

transactions when doing wiring repairs.

replacements.

finish".

when replacing a module.

transactions when doing wiring repairs.

control issues.

conductive finish.

the TIS Service Programming System (SPS), set-up and warranty.

long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.

it is warranty or not.

control issues.

reprogram modules.

Midtronics GR8 Battery Tester/Charger required for claim processing on labor operations 4041510, 4041520 and 250 mile/400 km labor operation restriction (North America ONLY).

it is warranty or not.

it is warranty or not

control issues.

On these vehicles, if the side doors will not open from inside the vehicle due to low or no battery voltage, such as a discharged or disconnected battery, or if the vehicle is entered without the key fob or the fob is not working, customers are being advised that the driver and passenger side doors can still be opened from inside the vehicle by using the manual release levers located on the floor between the seats and the door openings. Also, if the vehicle's side doors will not open from outside the vehicle due to low or no battery voltage, such as a discharged or disconnected battery, or if the key fob is not working, customers are being advised that the driver side door can still be opened by using their key to manually open the vehicle's trunk and pulling the manual door release tab located in the trunk.

On these vehicles, the wire harness connector from the seat side airbag and buckle tensioner to the body has a design interference between the vertical adjust crossbar and the carpet. When the seat is moved forward or back, the connector may be dragged along the carpet, pulling terminals loose or pulling the connector apart. This will cause a diagnostic trouble code to be set and the service airbag light will be illuminated. Dealers are to replace the affected harness connection with a soldered connection.

replacements.

revised wiring repair labor operations and required additional information.

Some vehicles may have a condition where a fuel odor is detected, fuel droplets appear below the left-hand fuel tank with fuel gauge level above 1/2, or a malfunction indicator lamp illuminates due to a leak path in the left-hand fuel pump module flange. If the condition occurs within the stated terms dealers are to replace the left hand fuel tank fuel pump module.

replacements.

issues.

ECM calibrations.

battery tester/charger.

application.

applications.

Some vehicles may have a condition where a fuel odor is detected, fuel droplets appear below the left-hand fuel tank with fuel gauge level above 1/2, or a malfunction indicator lamp illuminates due to a leak path in the left-hand fuel pump module flange. If the condition occurs within the stated terms, dealers are to replace the left hand fuel tank fuel pump module.

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

long period of time and/or set in cold weather climates to correct a customer concern of symptoms that include, but not limited to, a slow or no crank condition that may be caused by a discharged battery.

required.

rules and regulations for Canada only.

Some vehicles may have a condition where a fuel odor is detected, fuel droplets appear below the left-hand fuel tank with fuel gauge level above 1/2, or a malfunction indicator lamp illuminates due to a leak path in the left-hand fuel pump module flange. If the condition occurs within the stated terms, dealers are to replace the left hand fuel tank fuel pump module.

DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.

DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

replacements.

(DTC)(s) P0601, P0602, P0603, P0604, P0606, P062F, P06F3, P1621 which can be shared in multiple modules.

drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.

On some vehicles, equipped with power seats, the wire harness connector from the seat side airbag and buckle tensioner to the body has a design interference between the vertical adjust crossbar and the carpet. When the seat is moved forward or back, the connector may be dragged along the carpet, pulling terminals loose or pulling the connector apart. This will cause a diagnostic trouble code to be set and the service airbag light will be illuminated. Dealers will replace the affected harness connectors with accessory wiring harness components. The repairs will be made at no charge to the customer.

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

ONLY)

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system. Technician should understand the power cycles of the various OnStar systems. All Generation 6, 7, 8, and 9 systems are powered up continuously for 48 hours from ignition off. After 120 hours from ignition off, these systems then completely power off. The Onstar modules draw: * IGN ON - 240 to 400 Milliamp. * IGN OFF - 3 to 20 Milliamp for 48 hours or 120 hours on Gen 9 and vehicle communication platforms. * IGN OFF - 0.2 to 0.8 Milliamp after 48 hours or 120 hours on Gen 9 and vehicle communication platforms.

Communication Interface Modules (VCIM) (GMNA Only)

DETECTED" message when attempting to start the vehicle. Technician will need to ensure the battery is adequately charged to start vehicle. Also check the battery in the FOB to ensure it is 2 to 3 direct current volts. Technician will need to get in the vehicle with a known good fob press the Start Button. Listen for a click noise or a series of click noises from the Remote Control Door Lock Receiver. If there is only one click instead of a series of clicks, then the transistor internal to the Remote Control Door Lock Receiver is not operating properly. For this condition, replace the Remote Control Door Lock Receiver module.

"off route" messages while following Turn by Turn route. Technicians will need to remove power from the Vehicle Communication Interface Module for one hour and retest for the concern.

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.

TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.

THIS LETTER IS BEING SENT TO BRING TO THE CUSTOMER'S ATTENTION FEATURES THAT ARE COVERED IN THE VEHICLE'S OWNER MANUAL IN SITUATIONS WHERE THE CUSTOMER VEHICLE SIDE DOORS WILL NOT OPEN FROM INSIDE AND OUTSIDE THE VEHICLE DUE TO LOW OR NO BATTERY VOLTAGE. DEALERS ARE ALSO INSTRUCTED THAT IN CORRELATION WITH THIS CUSTOMER ADVISORY LETTER, A WEB-BASED TRAINING COURSE WILL BE REQUIRED FOR ALL CADILLAC AND CHEVROLET SALES CONSULTANTS, SALES MANAGERS, SERVICE CONSULTANTS, SERVICE MANAGERS, AND FIELD STAFF BEGINNING Q1 2016 VIA THE GM CENTER OF LEARNING.

THIS LETTER IS BEING SENT TO BRING TO THE CUSTOMER'S ATTENTION FEATURES THAT ARE COVERED IN THE VEHICLE'S OWNER MANUAL IN SITUATIONS WHERE THE CUSTOMER VEHICLE SIDE DOORS WILL NOT OPEN FROM INSIDE AND OUTSIDE THE VEHICLE DUE TO LOW OR NO BATTERY VOLTAGE. DEALERS ARE ALSO INSTRUCTED THAT IN CORRELATION WITH THIS CUSTOMER ADVISORY LETTER, A WEB-BASED TRAINING COURSE WILL BE REQUIRED FOR ALL CADILLAC AND CHEVROLET SALES CONSULTANTS, SALES MANAGERS, SERVICE CONSULTANTS, SERVICE MANAGERS, AND FIELD STAFF BEGINNING Q1 2016 VIA THE GM CENTER OF LEARNING.

THIS LETTER IS BEING SENT TO BRING TO THE CUSTOMER'S ATTENTION FEATURES THAT ARE COVERED IN THE VEHICLE'S OWNER MANUAL IN SITUATIONS WHERE THE CUSTOMER VEHICLE SIDE DOORS WILL NOT OPEN FROM INSIDE AND OUTSIDE THE VEHICLE DUE TO LOW OR NO BATTERY VOLTAGE. DEALERS ARE ALSO INSTRUCTED THAT IN CORRELATION WITH THIS CUSTOMER ADVISORY LETTER, A WEB-BASED TRAINING COURSE WILL BE REQUIRED FOR ALL CADILLAC AND CHEVROLET SALES CONSULTANTS, SALES MANAGERS, SERVICE CONSULTANTS, SERVICE MANAGERS, AND FIELD STAFF BEGINNING Q1 2016 VIA THE GM CENTER OF LEARNING.

MODE AFTER THE ONSTAR CANADA UPGRADE TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

MODE AFTER THE ONSTAR CANADA UPGRADE, TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER ONSTAR GROUP FOR FURTHER ASSISTANCE.

RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.

DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.

ON THESE VEHICLES, IF THE SIDE DOORS WILL NOT OPEN FROM INSIDE THE VEHICLE DUE TO LOW OR NO BATTERY VOLTAGE, SUCH AS A DISCHARGED OR DISCONNECTED BATTERY, OR IF THE VEHICLE IS ENTERED WITHOUT THE KEY FOB OR THE FOB IS NOT WORKING, CUSTOMERS ARE BEING ADVISED THAT THE DRIVER AND PASSENGER SIDE DOORS CAN STILL BE OPENED FROM INSIDE THE VEHICLE BY USING THE MANUAL RELEASE LEVERS LOCATED ON THE FLOOR BETWEEN THE SEATS AND THE DOOR OPENINGS. ALSO, IF THE VEHICLE'S SIDE DOORS WILL NOT OPEN FROM OUTSIDE THE VEHICLE DUE TO LOW OR NO BATTERY VOLTAGE, SUCH AS A DISCHARGED OR DISCONNECTED BATTERY, OR IF THE KEY FOB IS NOT WORKING, CUSTOMERS ARE BEING ADVISED THAT THE DRIVER SIDE DOOR CAN STILL BE OPENED BY USING THEIR KEY TO MANUALLY OPEN THE VEHICLE'S TRUNK AND PULLING THE MANUAL DOOR RELEASE TAB LOCATED IN THE TRUNK.

ON THESE VEHICLES, THE WIRE HARNESS CONNECTOR FROM THE SEAT SIDE AIRBAG AND BUCKLE TENSIONER TO THE BODY HAS A DESIGN INTERFERENCE BETWEEN THE VERTICAL ADJUST CROSSBAR AND THE CARPET. WHEN THE SEAT IS MOVED FORWARD OR BACK, THE CONNECTOR MAY BE DRAGGED ALONG THE CARPET, PULLING TERMINALS LOOSE OR PULLING THE CONNECTOR APART. THIS WILL CAUSE A DIAGNOSTIC TROUBLE CODE TO BE SET AND THE SERVICE AIRBAG LIGHT WILL BE ILLUMINATED. DEALERS ARE TO REPLACE THE AFFECTED HARNESS CONNECTION WITH A SOLDERED CONNECTION.

RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.

DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.

TESTER/CHARGER FOR DIAGNOSING BATTERY REPLACEMENTS AND MAINTAINING BATTERIES ON NEW VEHICLES IN DEALER INVENTORY.

CONTROL MODULES

THIS MAY NOT HAVE BEEN A CONCERN UNTIL RECENT REPAIRS WERE PERFORMED THAT MAY HAVE AFFECTED AIR FLOW OR ECM PROGRAMMING. *PE

ON, DTC C0561 SET (REPROGRAM EBCM). *NJ

*KB

IN THE TCM NO PRNDL DISPLAY NO CRANK. *KB

*KB

*TT UPDATED 2/15/08. *NJ

and Canada Dealers Only).

E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.

the warranty transaction submission procedures that support the Personal Property Damage process.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

a fluid leak, and what is considered fluid seepage.

programs.

E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

Vibration Analysis-Road testing procedure when diagnosing vibration concerns.

Only).

and Canada Dealers Only).

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Dealers Only).

Spin-On Oil Filters.

Dealers Only).

the warranty transaction submission procedures that support the Personal Property Damage process.

Only).

E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

and Canada.

Spin-On Oil Filters.

causing multiple customer concerns that do not have other diagnostic methods to identify them.

Spin-On Oil Filters.

Spin-On Oil Filters.

independent causes (GM Canada Dealers Only).

Spin-On Oil Filters.

Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.

Only).

programs.

programs.

Dealers Only).

programs.

E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).

E4403, M4404, M4413, E4414, E4423, E4491 or E6961).

requirements for the dealer to comply.

field action customer reimbursement procedure (U.S. Dealers Only).

considered warranty and non-warranty.

programs.

Warranty Information.

considered warranty and non-warranty.

Operations and Customer Enthusiasm

service.

process and to encourage delivering quality vehicles and generating higher CSi scores.

requirements for the dealer to comply.

can be approved by TAC and where the electronic parts can be returned to.

acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.

its customers.

acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.

reimbursement procedure.

service.

warranty claims submission procedures that support Labor Operation 0600014 ? Suspected Tampering or Vehicle Modifications.

operations and customer enthusiasm.

tools that include consumable parts (U.S. Only).

was at fault of the cutomer and how to properly claim them on the warranty paperwork

comebacks, and the possibility of buyback situations by outlining specific guidelines, strategy and forms that will assist with this goal, by identifying, clarifying and documenting customer concerns accurately at each service visit.

that vehicles can be fixed right the first time in for service.

operations to claim when the concern cannot be duplicated. Also provides information on how to submit claims within the global warranty managment.

service.

Guidelines.

warranty transaction submission procedures that support the Personal Property Damage process.

programs.

E4413, E4414, E4423 or E4491).

Operations and Customer Enthusiasm

offered through GM.

refered to Article 3.2.9 of the 1st addition manual for details of Technician Identification and Accounting of Labor Time

acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.

acceptable - customer authorization; Service manager approvals and transaction authorization; Details of concern, cause and correction; Labor Time; Technician ID and acoutablity of labor time; Proper documentation and retension of warranty parts; Accurate sublet charges and receipts; Add on concerns after the Job Card has been written.

Operations and Customer Enthusiasm

tools that include consumable parts (U.S. Only).

programs.

only) for service operations.

warranty claims submission procedures that support Labor Operation 0600014 - Suspected Tampering or Vehicle Modifications.

(WPC), and Parts Return Program information.

Empowerment Program and Goodwill Cases.

labor operation numbers and how to submit CCND.

Vehicles and Generating Higher CSi Scores

what is acceptable and not.

procedures.

The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.

part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold individually.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.

1-2-3-4 / 3-5-R Housing and Pump Seal Rings)

the throttle plate is opened rapidly and advises the customer that it is normal for the delay.

after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

transmissions.

TransFlow.

customers concern of Slips in Reverse or Third, Delayed Reverse or Drive Engagement and MIL on.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

manual transmissions that repair attempts will not change.

releasing of the 2-4 band and application of the 3-4 clutch assembly during an upshift. Also during a 3-2 downshift, the releasing of the 3-4 clutch during the application of the 2-4 band, can cause torque reversal down the output shaft creating a clunk. This is a normal condition.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

The different noises caused by driver habit, weather conditions , and normal manual transmission noises.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

after the vehicle has been sitting for a period of time. Technician can update the Transmission Control Module if working on a model year 2007. On all other model years dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.

documentation and claim submissions

communications, intermittent no crank, IP gauge fluctuation, intermittent door lock cycling /chime operation, various IP warning lamps illuminated, transmission may not shift, communication DTCs U0073, U0100, U0101, U0102, U0109, U0121 or U0140 set.

essential tool J-45096 TransFlow.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.

INDICATOR LAMP (MIL) WOULD BE ON, WITH DIAGNOSTIC TROUBLE CODE (DTC) P0796 FOUND AS ACTIVE. *PE

1-2-3-/ 3-5-R HOUSING AND PUMP SEAL RINGS). THIS CONDITION MAY BE CAUSED BY A CRACKED 1-2-3-4/ 3-5-R CLUTCH HOUSING. *JS UPDATED 5/10/12. *PE UPDATED 04/15/2014 *JS

INTERMITTENT CHIME OPERATION, VARIOUS IP WARNING LAMPS ILLUMINATED, TRANSMISSION MAY NOT SHIFT, COMMUNICATION DTCS U0073, U0100, U0101, U0102 U0121 OR U0140 SET (REPAIR TERMINALS IN TRANSMISSION HARNESS CONNECTOR, REPAIR OPEN OR SHORTED GM HIGH SPEED LAN CIRCUITS, OPEN OR SHORTED DATA LINK RESISTOR, CORROSION OR POOR CONNECTIONS IN VARIOUS CONTROL MODULE CONNECTORS). *JS

TRANSMISSION MAY NOT SHIFT, DTCS U0073, U0100, U0101, U0102, U0121, U0140 SET (REPAIR BACKED OUT TERMINAL IN TRANSMISSION HARNESS CONNECTOR). VEHICLES WITH 6 SPEED 6L80 (RPO MYC), 6L90 (RPO MYD) OR HYBRID TWO MODE 2M70 AUTOMATIC. INCLUDING 2008 TAHOE AND YUKON HYBRID MODELS. *PE UPDATED 3/28/11. INCLUDING SIERRA, SILVERADO AND ESCALADE HYBRIDS. *PE

TRANSMISSION MAY NOT SHIFT, DTCS U0073, U0100, U0101, U0102, 70140 (REPAIR BACKED OUT TERMINAL IN TRANSMISSION HARNESS CONNECTOR). *PE

EQUIPPED WITH 6L80 (RPO MYC) AUTOMATIC TRANSMISSION. *NJ

*KB

AUTOMATIC TRANSMISSION - INFORMATION ON TRANSMISSION FLUID PRESSURE (TFP) SWITCH CHECK FOR FALSE DTC'S P0842, P0843, P0872, P0873, P0877, P0878, P0989, OR P0990. *KB

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

Replacement Guidelines.

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

Replacement Guidelines.

Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.

have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.

when the protective shipping film is removed from certain vehicles.

chromed aluminum wheels, along with warranty information regarding these conditions.

Speeds

(IP), hard or plastic surfaces, seats, carpet, leather, vinyl, fabric cleaner, stain remover, restorer and product availability.

the tire can be properly repaired under the new tire warranty.

pitting corrosion and/or spotted.

replace any glass for this reason.

flanges when the repairs are done.

to verify they correct a condtion of the power folding mirriors glass shakes, flutters at normal driving conditions.

that have the condition of rust showing at hem flange

for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)

operation, the technician may find that the Tech2 value for the Rear Tonneau Status is blank. This blank value is caused by a Tech2 software malfunction and has nothing to do with the function or operation of the vehicle. Technician should always reference published diagnostics and the latest revision of technical service bulletin 03-08-67-008 when diagnosing any trunk or folding top concerns.

cleaners to use to fix the conditions due to multiple causes.

of power fold away mirriors glass shakes or flutters at normal driving speeds

Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability

TO VERIFY THEY CORRECT A CONDTION OF THE POWER FOLDING MIRRIORS GLASS SHAKES, FLUTTERS AT NORMAL DRIVING CONDITIONS.

VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.

AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.

*RM UPDATED ON 5/2/2012. *KB

HANDLE SWITCH, REPLACE IF NECESSARY). *NJ

additive.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

additive.

additive.

customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

additive.

diesel fuel.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.

rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.

rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

using the evaporative emission cart smoke machine and ultrasonic leak detectortools.

debris have entered the exhaust system.

Also, a bullet was added to the dexos 2? section with information on the 2014 Cruze diesel.

additives.

usage of E85 fuel in GM vehicles.

the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.

vehicle, the fuel gauge only reads half tank or a difficult time filling the fuel tank. Technician should inspect the inspect the Evaporative Emissions System vent hose for a kink.

THERE MAY BE A FAULT CODE PRESENT. *RM

*KB

repairs requiring balance and Road Force measurement.

Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

repairs requiring balance and Road Force measurement.

Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).

ride characteristics of GM cars and trucks.

Shake, Flat Spotting) of GM Original Equipment Tires.

possible chances of the customers concerns over tire vibration are repair.

possible chances of the customers concerns over tire vibration are repair.

tire leak and low tire psi message on.

possible chances of the customers concerns over tire vibration are repair.

used to install wheels onto vehicles

a tire using the balancer.

possible chances of the customers concerns over tire vibration are repair.

used to install wheels onto vehicles

Variations and the difference between balancing a flange and flangeless rim.

matching depth of socket used on the wheel nut.

used to install wheels onto vehicles

balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)

Distributor/Installers as to the proper methods for mounting, balancing, and installing accessory wheels and tires.

Program and Global Warranty Management (GWM) Submission Information.

management submission information.

*NJ

*TT

considered a fluid leak, and what is considered fluid seepage.

considered a fluid leak, and what is considered fluid seepage.

considered a fluid leak, and what is considered fluid seepage.

considered a fluid leak, and what is considered fluid seepage.

Information and Transaction Submissions Procedure and general content updates.

Operation.

Operations.

operations.

Code and update the tool reference information.

Operation.

under Courtesy Transportation Warranty Transaction Submission.

version of Bulletin 12-00-89-003.

is considered a fluid leak, and what is considered seepage.

and Canada Only)

statement, change the terms Claim Type B to Claim Type ZPTI, GM Dealer to GM Service Agent, Repair Order to Job Card, Warranty Claim to Warranty Transaction, and to update the Procedure Information for submitting Vehicle Repairs from WINS to Global Warranty Management (GWM).

Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.

is considered a fluid leak, and what is considered seepage.

A CONDITION OF THE REAR ENTERTAINMENT SYSTEM NOT OPERATING AS INTENDED IN COLDER AMBIENT TEMPERATURE AREAS DUE TO CALIBRATION CONCERNS.

*RM UPDATED 12/6/11. *PE

*KB UPDATED 4/11/08. *NJ

*SC UPDATED. *KB UPDATED 9/30/08. *PE

feedback form to the GM navigation disc center website.

feedback form to the GM navigation disc center website.

feedback form to the GM navigation disc center website.

While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

information.

warranty or not.

techline/service programming systems.

that they only get a few channels.

Technician will need to use a scan tool and verify current Digital Radio Receiver Status under Data Display. Technician will need to look at the second line labeled Digital Radio Receiver Status will display a number of 00 - 04. Technician will repair per the status code.

Discs .

Instrument Panel Clusters (IPCs)

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a ?500 phone number? The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

XM Traffic or Weather for the local area takes several minutes to update and may read "NO DATA" or "UPDATING" during that time. Technician should be advised that Traffic and Weather data from local reporting stations and then send the updated info process may take up to 24 minutes. Technician should test for full operation of the XM band if the system has not started receiving the Traffic and weather update within 30 minutes. Also ensure the customer has not shut XM NavTraffic off in the user settings of the navigation radio. Technician will need to contact XM customer assistance to review the account status and verify that the XM Traffic option has been enabled and is available in the area.

disc after the radio or CD changer was recently serviced for a different customer's concern. Technician will need to ensure the shipping pin was removed from the radio.

set of universal coaxial repair kits to service vehicles. This only applies to cable used for high frequency signals, such as cellular (OnStar), satellite radio (XM) and GPS (navigation). The kits do NOT apply to the AM/FM cables.

An issue with the Head Up Display image may not appear clear can be caused by a non-original equipment manufacturer windshield installed. Another issue that may be present with the Head Up Display is the segments illuminate intermittently this can be caused by the ambient lighting conditions. A poor or hazy Head Up Display image can be caused by Instrument Panel emit fumes that cause a film to form on the HUD lens. Technician will need to use Isopropyl Rubbing Alcohol to clean the lens.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

Dealer should be advised at this time, there are no provisions to add this option to vehicles that were not built with it.

THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.

Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

Fog/Driving Lamp Damage.

Accessories.

Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.

the Proper use of GM Simplified Maintenance Schedules.

Guidelines.

Guidelines.

recommended practices.

flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).

message when a media disc is installed. Technician will need to check the Regular Production Option Code list to verify if the disc is compatible.

Light Duty Trucks.

For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

what should be considered warranty replacement and not

Additives) and Proper Use of GM Simplified Maintenance Schedules (U.S. Only)

inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.

flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).

headlamp, tail lamp, license lamp or fog/driving lamp damage that are not considered warrantable.

vendor.

For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.

at start up after cold soak and that this is considered a normal conditon and no repairs are necessary

strut due to fluid leak.

strut due to fluid leak.

repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

and strut due to fluid leak.

REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. TECHNICIAN WILL NEED TO DETERMINE WHAT TYPE OF CALL THE CUSTOMER IS HAVING THAT IS UNWANTED. THE VEHICLE MAY RECEIVE AN INCOMING CALL JUST LIKE ANY OTHER PHONE. TYPICALLY THE CUSTOMER WILL HEAR THE PHONE RINGING IN THE VEHICLE. THIS SCENARIO ALSO INCLUDES INCOMING BLUETOOTH CALLS. ONE TYPE OF UNWANTED CALL CAN BE MADE IF THE KEY PAD IS FAULTY THE ONSTAR SYSTEM WILL TRY TO MAKE A BLUE BUTTON CALL FOR SHORTED VOLTAGE IN THE CIRCUITS. THE ONSTAR MODULE COULD HAVE AN INTERNAL FAULT AND PRODUCE A PHONE UNAVAILABLE AUDIO MESSAGE ALSO IT MAY HAVE A DIAGNOSTIC TROUBLE CODE U1500 OR B1000. REFER TO DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODE MAKING SURE TO FOLLOW ANY APPLICABLE BULLETINS OR PRELIMINARY INFORMATION SHEETS. A GREADYH OR GONSTAR READYH AUDIO MESSAGE HEARD WHILE DRIVING. IN SOME CASES IT HAS BEEN FOUND THAT THE CUSTOMER IS INADVERTENTLY PRESSING THE PUSH TO TALK BUTTON ON THE STEERING WHEEL CONTROLS. ON RARE OCCASIONS, OTHER ISSUES IN THE STEERING COLUMN OR STEERING WHEEL CONTROL SYSTEM MAY INDUCE THIS CONCERN.

MODEL 2005-09 SLUR, 2005-13 CORVETTE. *PE

DIAGNOSTIC COMPONENT TEST PROCEDURE AND REPAIR AS NECESSARY). *PE UPDATED 5/6/09. *PE

*TT

The customer communication requested return of unsold inventory to inspect the housing. There may be a gap between the 2 halves of the housing causing the actuator to bind and a loss of HVAC air door control. Loss of HVAC air door control can lead to discomfort as it may be stuck in a single orientation.

concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.

cold weather climates and testing those batteries.

cold weather climates and testing those batteries.

emanating from HVAC system.

emanating from HVAC system.

Upholstery, Accessory Seat Heaters or Other Comfort Enhancing Devices

PERIOD OF TIME AND/OR SET IN COLD WEATHER CLIMATES AND TESTING THOSE BATTERIES.

belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.

BUCKLE RELEASE BUTTON IS STICKING. SEAT BELT WARNING LIGHT ILLUMINATED. LIKELY CAUSED BY STICKY BEVERAGES THAT ARE SPILLED INTO THE BUCKLE ASSEMBLY. *RM UPDATED 4/3/12. *PE

*MJ

has a fluid residule from a possible external source from a leaking shaft seal.

MODELS 2004-2009 XLR; 1997-2013 CORVETTE. *PE

reservoir.