2015 Cadillac Escalade TSBs
1,000 Technical Service Bulletins across 17 categories
Categories
Engine
307 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of...
Read full bulletin
engine related shudder.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston.
This PI communicates a procedure to clean oil leaking from the rain sensor.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides information to the technician about fluid leaking from the brake...
Read full bulletin
caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
This service bulletin advises the technician of possible coolant entering the areas of the engine, either through failed...
Read full bulletin
parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication advises the technician on a parts restriction on the Generation I 8 speed...
Read full bulletin
rear wheel drive valve bodies.
This Preliminary Information communication advises the technician on a parts restriction on the Generation I 8 speed...
Read full bulletin
rear wheel drive valve bodies.
This Preliminary Information communication provides information to the technician that a customer may request the...
Read full bulletin
factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This informational bulletin advises the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this...
Read full bulletin
occurrence.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
This bulletin updates the position of General Motors on refinishing aluminum wheels.
Read full bulletin
GM has determined that wheel refinishing under warranty will no longer be performed.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
Programming IPC Engine Hours Into A Replacement IPC.
This service bulletin advises the technician of possible coolant entering the areas of the engine, either through failed...
Read full bulletin
parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
Delayed Engagement After Sitting With Engine Off
Various Engine Noises During Cold Start and Warm Engine Operation
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension...
Read full bulletin
housing and to perform testing on transmission for other possible issues, but it still may be possible on high mileage vehicles that orifices in housing may have come dislodged, causing the same customer concern.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This bulletin provides a service procedure to reprogram the Chassis Control Module (CCM) on certain 2015 model year...
Read full bulletin
Cadillac ATS vehicles equipped with a 2.0L or 2.5L engine (LTG/LCV). The switchable engine mount calibration currently in these vehicles is not the intended calibration for the "Tour/ECO" vehicle modes. Operating the vehicle in the "Tour/ECO" mode could result in a poor ride quality (shake) on rough roads. This could also result in less life to the engine mounts. and subsequent fluid leakage from the mounts.
PSR-Overheated Exhaust Components - Equipped with 4.3L Engine (LV1/LV3)
Delayed Engagement After Sitting With Engine Off
Various Engine Noises During Cold Start and Warm Engine Operation
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This informational bulletin advised the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of...
Read full bulletin
engine related shudder.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides information for after installation of a replacement upper valve body, the transmission...
Read full bulletin
may have no Reverse and no 2nd gear.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This service bulletin advises the technician that the possible cause may not be from a faulty clutch piston or extension...
Read full bulletin
housing and to perform testing on transmission for possible other issues, but it still may be possible on high mile vehicles that orifices in housing may have come dislodged, causing the same customer concern.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head...
Read full bulletin
gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin advises the technician to Inspect the position of the head gasket locating tabs to determine if the head...
Read full bulletin
gasket(s) has been possibly installed backwards to correct a concern of an Engine Thermostat Tick Noise and/or Running Hot.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of...
Read full bulletin
engine related shudder.
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise.
Read full bulletin
Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold...
Read full bulletin
or the vehicle has sat for a few hours.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through...
Read full bulletin
failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
This technical bulletin provides a procedure to replace the camshaft actuator magnet to correct customer concerns of...
Read full bulletin
engine related shudder.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint.
Read full bulletin
GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).
Information bulletin explains a possible coolant leak coming from the cylinder head bolt areas.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates to dealers an issue on remanufactured engines with part numbers 19368174...
Read full bulletin
and19368176where the incorrect crankshaft timing gear was installed. Provides dealer with information to correct this condition.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary information communicates a condition where there is only newer hardware available when replacing the Active Safety Control Module.
Read full bulletin
The newer hardware is not compatible with whatis currently loaded into the SPS programming system. Engineering is working on a new software set to address the concern.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates to dealers an issue on remanufactured engines with part numbers 19368174...
Read full bulletin
and19368176where the incorrect crankshaft timing gear was installed. Provides dealer with information to correct this condition.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This service bulletin provides diagnostic information for a customer concern of engine vibration.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This service bulletin provides diagnostic information for a customer concern of engine vibration.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
Service Update Bulletin (Labor Codes Added).
Read full bulletin
Certain vehicles may have a condition where the engine control module (ECM) software allows the Auto Stop to occur at a state of charge below 65%. Auto Stop is supposed to be inhibited at 65% to protect against excessive battery wear and discharge. Dealers are to reprogram the ECM.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this...
Read full bulletin
occurrence.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise.
Read full bulletin
Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This SKU is a Power Window Regulator and Motor Assembly.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.
This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to...
Read full bulletin
eliminate coolant smell and/or a slight leak at the radiator.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in...
Read full bulletin
Drive concern.
This service bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in...
Read full bulletin
Drive concern.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection.If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
Special Coverage Adjustment - In some circumstances, some 2014-2018 model year Cadillac Escalade, Chevrolet Silverado,...
Read full bulletin
Chevrolet Suburban, Chevrolet Tahoe, GMC Sierra, and GMC Yukon vehicles may have a condition where customers may experience increased brake pedal effort, hard brake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applying the brakes. The engine mounted mechanical vacuum pump output may decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervals could contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5 minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs, the hydraulic brake system remains functional but may require additional pedal force. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Bulletin provides the technician with information on how to perform a oil consumption test and a procedure to...
Read full bulletin
replace the pistons if found the cause of the oil consumption.
This informational bulletin advises the technician of possible coolant entering the areas of the engine, either through...
Read full bulletin
failed parts or defects in the castings, that may be the cause of the concerns related to the MIL or the engine running rough.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up.
Read full bulletin
White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Bulletin provides the technician with information on how to perform a oil consumption test and a procedure to...
Read full bulletin
replace the pistons if found the cause of the oil consumption.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in...
Read full bulletin
Drive concern.
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold...
Read full bulletin
or the vehicle has sat for a few hours.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL Illuminated.
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold...
Read full bulletin
or the vehicle has sat for a few hours.
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
This SKU is a Power Window Regulator and Motor Assembly.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.
This SKU is a Power Window Regulator and Motor Assembly.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the software. The software may be too sensitive to the position of a locating magnet in the assembly causing the activation of the pinch point threshold prematurely. The window will stay open when it should have closed.
This informational bulletin explains the difference in AFM and DFM engines and what is and is not activated during this...
Read full bulletin
occurrence.
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a...
Read full bulletin
guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about vehicles that may have a service...
Read full bulletin
engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for...
Read full bulletin
customer concerns related to wheel alignment.
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin...
Read full bulletin
has been sheared away to correct a crank/No Start condition.
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician how to diagnose and repair a vehicle...
Read full bulletin
with an engine that runs with an intermittent crank no start with a Diagnostic Trouble Code P0011 or P00C6 current or history. The Camshaft Position Actuator Solenoid Valve may be sticking or binding causing the valve timing to be retarded. Dealer will need to cycle the Camshaft Position Actuator Solenoid Valve by energizing it using Global Diagnostic System 2.
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being...
Read full bulletin
overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and...
Read full bulletin
repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
This Preliminary Information communication provides information to the technician that a customer may request the...
Read full bulletin
factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
This diagnostic tip provides a procedure to aid in performing a diagnostic test to verify if the camshaft alignment pin...
Read full bulletin
has been sheared away.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection.If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This engineering information bulletin ends the need for information from the field on an Intermittent No Forward and/or...
Read full bulletin
No Reverse While Driving condition. If this condition is encountered, refer to SI for further diagnosis.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
N182202780 01 - Special Coverage.
Read full bulletin
Certain Vehicles may have a condition where customers may experience increased brake pedal effort, hardbrake pedal, and/or potentially increased stopping distance. The condition is more prevalent at low speed when softly applyingthe brakes. The engine mounted mechanical vacuum pump outputmay decrease over time decreasing the amount of vacuum/power brake assist. Failure to follow recommended oil change intervalscould contribute to this condition. The Driver?s Information Center, (DIC) ?Service brake assist? alert will activate 2-5minutes after the vacuum level drops, and a Diagnostic Trouble Code, (DTC) will also be set. Even where this condition occurs,the hydraulic brake system remains functional but may require additionalpedal force. Please be aware that even if the vehicle exhibits this condition, it meets all federal motor vehicle safety standards forbrake performance. Dealers are to replace the vacuum pump and vacuum pump belt. The repairs will be made at no charge to the customer.
This Preliminary Information communication provides information to the technician on the steps needed to diagnose and...
Read full bulletin
repair vehicles that may have a rattle noise from the dash. Technician will need to inspect for the rear heater pipes contacting the passenger side exhaust manifold. If the rear heater pipe is found to be contacting the exhaust manifold, reposition the heater pipe so it no longer makes contact.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This diagnostic tip provides additional information on how to diagnose a possible valve, lifter or camshaft issue.
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in...
Read full bulletin
Drive concern.
This diagnostic tip provides information to the tech to aid in performing a diagnostic test to verify if the camshaft...
Read full bulletin
alignment pin has been sheared away.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This engineering information bulletin is requesting information from the field to validate a field fix.
Read full bulletin
Before contacting engineers, remove the transmission oil pan and inspect for nickel to quarter size pieces of aluminum debris in the oil pan. The 2-3-4-6-8 and 4-5-6-7-8 reverse clutch assembly and the 1-3-5-6-7 clutch assembly may be broken in several pieces.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after...
Read full bulletin
severe internal engine damage.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have Diagnostic Trouble Code P06DD or no or low oil pressure. Technician will replace timing chain tensioner guide. If oil pump face is damaged and or worn thru replace oil pump. Inspect bearings for damage wear due to debris from oil pump.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact Partechand/orthe Techline Customer Support Center for additional support.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using...
Read full bulletin
the Tech 2 or GDS 2.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Bulletin provides the technician with information on how to perform a oil consumption test and a procedure to...
Read full bulletin
replace the pistons if found the cause of the oil consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector X154 located on the front cover next to the vacuum pump.
This Preliminary Information communication provides information to the technician for a vehicle setting both a P2635 and...
Read full bulletin
P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range. Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2. Navigate to fuel system depressurize and at engine idle depressurize the fuel system. The fuel pressure sensor value should drop to 0 and the engine will stall. If a sensor is causing this concern the suspected sensor will not drop to 0 the engine will stall however the sensor will still read 30 to 40 pounds per square inch.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This Preliminary Information communication provides information to the technician about vehicles that are equipped with...
Read full bulletin
6L80 Regular Production Option Code (MYC), 6L90 Regular Production Option Code (MYD) or 8L90 Regular Production Option Code (M5U) Automatic Transmission, now have Powertrain Grade Braking. Powertrain grade braking assists when driving on a downhill grade to help maintain desired vehicle speed by using the engine and transmission to slow the vehicle.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This Bulletin provides the technician with information on how to perform a oil consumption test and a procedure to...
Read full bulletin
replace the pistons if found the cause of the oil consumption.
This Preliminary Information communication provides information to the technician for a Service Engine Soon light with a...
Read full bulletin
Diagnostic Trouble code P0300 set. There may be a rough running engine associated with this concern. If service information diagnostics have been completed and there is still no trouble found, the technician is to inspect for a possible terminal tension concern on the ignition coil power feed for the cause of the rough running engine and or the P0300. For the Service Engine Soon light or traction control lamp concern check the X2 connector of the under hood fuse block for poor pin retention.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up.
Read full bulletin
White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
This Preliminary information communicatesCheck Engine Light on and vehicle runs rough.
Read full bulletin
This condidtion will occur within the first 5 minutes after the vehicle is started.his condition may be caused by a software anomaly that allows all four DTC's P0132, P0137, P0152, P0157 to set. All 4 DTCs must be in history for this PI to apply.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection.If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
This Preliminary Information communication provides information to the technician about a no start or another concern...
Read full bulletin
after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
This informational bulletin explains the normal noises an engine may make when the ambient temperature outside is cold...
Read full bulletin
or the vehicle has sat for a few hours.
This technical bulletin provides a procedure to measure vibration and install engine mounts to correct a Rough Idle in...
Read full bulletin
Drive concern.
This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to...
Read full bulletin
eliminate coolant smell and/or a slight leak at the radiator.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This technical bulletin provides a procedure to repair the valve lifter oil manifold and/or lifters to correct the...
Read full bulletin
customers concern of engine misfire, ticking noise and/or MIL on.
This informational bulletin provides information for the dealer technician to gather as much information to help aid...
Read full bulletin
Engineers by completely filling out requested reports.
This informational bulletin provides information on a normal engine operating condition for faster emission warm up...
Read full bulletin
time.
This Bulletin provides the technician with information on how to perform a oil consumption test and a procedure to...
Read full bulletin
replace the pistons if found the cause of the oil consumption.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
This Preliminary Information communication advises the technician that generation 5 engines with Regular Production...
Read full bulletin
Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner’s Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.
This Preliminary Information communication advises the technician that there have been some reports that the current...
Read full bulletin
engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician about vehicles that may have a content...
Read full bulletin
theft alarm sounding for no apparent reason. Technician may use all published Service Information diagnostics and has not found the cause of the unwanted content theft alarm sounding. Technician should use Global Diagnostic System 2 to review the Body Control Module parameters for "Content Theft Deterrent Trigger History". If the trigger is an Intrusion inspect for items hanging from the rear view mirror, solar powered dancing characters. When the trigger is a Glass breakage inspect the two rear quarter-panel windows and also in the liftgate glass. The quarter panel windows are attached to the body harness with a connector that looks similar to a 9 volt battery connector inspect them to be fully seated in on the glass. When the trigger is Ignition Voltage/Battery reconnect detected during a cold ambient temperature remote vehicle start event technician should call GM General Motors Technical Assistance Center.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about vehicle that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P2635, U0074 and or U18A2. Technician will need to follow published diagnostics for Diagnostic Trouble Codes U0074 would take priority over U18A2 if both set before addressing DTC P2635.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This preliminary information bulletin provides a procedure for radiator and engine coolant thermostat replacement to...
Read full bulletin
eliminate coolant smell and/or a slight leak at the radiator.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This technical bulletin provides repair information for transmission control module reprogramming to correct a customer...
Read full bulletin
concern for MIL illuminated with firm shifts, shudder, engine RPM flare and DTCs P0606, P16F3 or P2818 set.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician about vehicles that have run hot and or has a tick noise.
Read full bulletin
Technician should inspect the head gaskets to ensure are not installed backwards. Technician should replace the head gasket if they are found installed backwards.
This Preliminary information communicates to the dealer additional information on checking for the engne crankcase being...
Read full bulletin
overfull on oil causing an engine vibration concern. The technician is advised to inspect for contaminnants and adjust the engine oil level as needed.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication advises the technician that generation 5 engines with Regular Production...
Read full bulletin
Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner's Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that a customer may request the...
Read full bulletin
factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and inspect the wiring for damaged or corroded circuits. Technician will repair any damaged or corroded circuits.
This Preliminary information communicatesP0016 setting after internal engire repair.
Read full bulletin
The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
This Preliminary Information communication provides information to the technician about vehicles that may have a service...
Read full bulletin
engine soon malfunction indicator lamp, antilock braking system malfunction indicator lamp, service suspension system message, misfire, hesitation, no crank, heater-vent-air conditioning inoperative. Technician may find F11UA, F104UA, F35UA, and or F60UA blown. Technician should inspect the engine harness near the vacuum pump pulley to be chafing. Technician will need to reroute the wire harness and repair and damaged wires.
This Preliminary Information communication advises the technician that there have been some reports that the current...
Read full bulletin
engine hours are not correct and display 0.0. Technician will need to program the Instrument Panel Cluster using Service Programming System.
This Preliminary Information communication provides information to the technician for a Service Engine Soon light with a...
Read full bulletin
Diagnostic Trouble code P0300 set. There may be a rough running engine associated with this concern. If service information diagnostics have been completed and there is still no trouble found, the technician is to inspect for a possible terminal tension concern on the ignition coil power feed for the cause of the rough running engine and or the P0300. For the Service Engine Soon light or traction control lamp concern check the X2 connector of the under hood fuse block for poor pin retention.
This Preliminary Information communication provides information to the technician of additional information when...
Read full bulletin
diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on and Diagnostic Trouble Code P0300 - P0308 may set. Technician will inspect for lose sparkplug wire. If a spark plug wire is found lose check for a missing ?C? clip on the wire end for the ignition coil. If the clip is missing replace the wire.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary information communicatesSES lamp, setting DTC P0333 when shifting the Transmissionfrom park.DTC P0333...
Read full bulletin
cansetdue to voltage from the Transmission park/neutral signal 1circuit bleeding into the knock sensor system circuits.If SI does not isolate the concern inspect the K20 ECM connector X2 looking for debris, connectorand or terminal concerns.
This Preliminary Information communication provides information to the technician on the steps to diagnose and repair...
Read full bulletin
vehicles that may have issues were the customer will need increased effort to depress the brake pedal. Technician may find fluid in the brake booster and/or the booster vacuum line. Technician will need to replace Vacuum Pump, Brake Booster, Master Cylinder, Vacuum Pump Belt and the Vacuum Line between the booster and the pump.
This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours.
Read full bulletin
This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about vehicles that have the oil...
Read full bulletin
pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (LV3), 5.3L (L83), 6.2L (L86) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
Pre-Delivery & Maintenance
161 bulletinsThis service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may...
Read full bulletin
not pass California smog inspection or smog inspection in other states.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on proper use of floor mats.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
Service 4WD Message ? Transfer Case Stuck in 4WD HI
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This service bulletin provides information on proper use of floor mats.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front...
Read full bulletin
grille or radiator area.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This service bulletin provides a diagnostic procedure to aid in correcting a customer concern of a Howling,...
Read full bulletin
Whining/Whirring Noise, Shudder/Vibration and/or Grinding Noise While in 4HI, 4HI Auto and/or During Parking Lot Maneuvers in Auto Mode.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and...
Read full bulletin
PF48.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles...
Read full bulletin
that may not pass California smog inspection or smog inspection in other states.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398,...
Read full bulletin
E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer...
Read full bulletin
Enthusiasm.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This warranty administration bulletin provides policy information on required operating procedures.
This Preliminary Information communication provides information to the technician only to provide additional tips when...
Read full bulletin
diagnosing a front heated seat concern and is not meant to be a diagnostic flow chart or replace Service Information. Always, perform and refer to Service Information for the latest diagnostic information and procedures.
This Preliminary Information communication provides information to the technician about vehicles that have an unwanted...
Read full bulletin
Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
Other
117 bulletinsThis preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
New Vehicle Monitoring Programs Section in IVH
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM...
Read full bulletin
technical assistance case using the dealer case management tool.
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Unable to Insert Or Eject Discs.
OnStar And XM Antenna Malfunction Setting.
Identifying If A Vehicle Is Equipped With OnStar 4G LTE Wi-Fi.
Itch Squeak Type Noise From HUD Area.
Front License Plate Bracket Color Change.
Important Information Needed When Calling TAC for Diagnostic Help on Vibration Complaints.
CD Player Inoperative.
CD Player Inoperative.
Information on Driveline Clunk Noise
Clunking Noise from Front of Vehicle During Turns and/or Bumps
Clunking Noise from Front of Vehicle During Turns and/or Bumps
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Unable To Install a CD Or DVD
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
Changing Turn-By-Turn Voice Response To Metric Or English Units
Information on Driveline Clunk Noise
Clunking Noise from Front of Vehicle During Turns and/or Bumps
Clunking Noise from Front of Vehicle During Turns and/or Bumps
Rattle Noise From Second Row Seat.
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
Canadian Customers Unable To Place Calls In The United States
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Preliminary information communicates a process to correct theconcern of Unable to contact OnStar after the 3G EOL...
Read full bulletin
on 2015-2022 model year vehicles in the United States.
This technical bulletin provides repair information to correct a customer concern of carpet damage, seat mounting stud...
Read full bulletin
wear through, hole in second row (Intermediate) carpet.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
Clunking Noise from Front of Vehicle During Turns and/or Bumps
This informational bulletin provides information on proper use of floor mats.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Essential Tools that Include Consumable Parts (U.S.
Read full bulletin
Only)
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify...
Read full bulletin
the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
IPC Odometer Programming Method Quick Reference Guide
This technical bulletin provides a procedure to reset the DTCs and take the vehicle for a test drive to verify the codes...
Read full bulletin
do not return.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This Technical bulletin provides a procedure to correct a customer concern of Blu-Ray Movies Do Not Start After Play...
Read full bulletin
Icon Selected on Menu.
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This technical bulletin provides repair information to correct a customer concern of carpet damage, seat mounting stud...
Read full bulletin
wear through, hole in second row (Intermediate) carpet.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended,...
Read full bulletin
causing the parking pawl to engage while driving.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This Preliminary Information communication provides information to the technician about vehicles that have a coolant...
Read full bulletin
loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers...
Read full bulletin
memory position.
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin provides information for the GM of Canada OnStar Cellular Communication Upgrade to 3G/4G LTE...
Read full bulletin
for vehicles that may need an upgrade.
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
This Preliminary information communicatesAFM / DFM usageInformation.
Read full bulletin
providing additional information on the AFM and DFM systems
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This technical bulletin provides a procedure to change the diff fluid if found the cause of the customers concern.
This informational bulletin provides information for dealers/technicians and customers on possible carpet color...
Read full bulletin
mismatch.
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This technical bulletin provides repair information to correct a customer concern of carpet damage, seat mounting stud...
Read full bulletin
wear through, hole in second row (Intermediate) carpet.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This informational bulletin provides information on proper use of floor mats.
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as intended,...
Read full bulletin
causing the parking pawl to engage while driving.
This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or...
Read full bulletin
click type noise while driving.
This informational bulletin provides information and operating tips for the hands free lift gate.
This technical bulletin provides repair information to correct a customer concern of carpet damage, seat mounting stud...
Read full bulletin
wear through, hole in second row (Intermediate) carpet.
This informational bulletin explains the importance of maintaining the vehicle.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This technical bulletin provides a procedure to validate if the parking pawl actuator is not working as attended causing...
Read full bulletin
the parking pawl to engage while driving.
This Preliminary Information communication advises the technician that the Product Quality Center part restriction has...
Read full bulletin
endedfor the 8L45 and 8L90 park actuator rod.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the...
Read full bulletin
customer.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This informational bulletin aids the technician on diagnosing possible vibrations in a vehicle, methods used for testing...
Read full bulletin
each scenario and documenting findings.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This technical bulletin provides repair information to correct a customer concern of front seat lateral movement and/or...
Read full bulletin
click type noise while driving.
This informational bulletin provides information and operating tips for the hands free lift gate.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This Preliminary information communicates a repair procedure for a squeak/squawk typenoise coming from the lower...
Read full bulletin
column/drivers footwellarea when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the bootwhere it passes through the boot.
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles.
Read full bulletin
A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers...
Read full bulletin
memory position.
This Preliminary Information communicates an issues with the headliner sagging and how to reattachthe velcrousing...
Read full bulletin
Hardman Double Bubble Epoxy part number 04001.
This informational bulletin provides information on how to use floor mats.
This informational bulletin ask the dealers for digital pictures to better enhance field reports only.
This information bulletin provides the dealers on how to submit a product information report.
This informational bulletin provides additional information to the technicians and how to submit a field product report.
This Preliminary information communicates
This Preliminary Information communication provides information to the technician about vehicles that have a detent /...
Read full bulletin
click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no repair attempts should be performed.
Electrical
90 bulletinsThis PI Addresses a possible solenoid wiring fault and how to inspect the build date to identify
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use...
Read full bulletin
for certain repairs, such as Wiring Harness Repairs.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance...
Read full bulletin
that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Special Return - Fuel Tank Module Kit: ACDelco Part Number M10256 (select date codes)
Unable to Clear BCM DTCs After Completing Repair
High Voltage Safety ? High Voltage Disabling
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This Preliminary Information communication provides information to the technician for the adaptive cruise control or...
Read full bulletin
lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
OnStar Module Battery Drain
False B127E Set In HMI Module
Front Shock Electrical Connector Terminal Removal.
Front Shock Electrical Connector Terminal Removal.
Interior Electrical Center Left End Cap Fuse Label Error
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Unable to Clear BCM DTCs After Completing Repair
Unable to Clear BCM DTCs After Completing Repair
OnStar Module Does Not Support All B101D Symptom Codes.
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
Transport Mode On Message Displayed in Driver Information Center (DIC) and/or Battery Light is Flashing (Follow...
Read full bulletin
Procedure as Outlined Below)
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This service bulletin provides information on Module Harvesting.
This Preliminary information communicates an issue where the chassis wiring harness can chaff on the underbody of the...
Read full bulletin
vehicle causing a wide varied of issues,depending on which wire(s) is chaffed.Repair the affected wiring as needed
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground...
Read full bulletin
at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical...
Read full bulletin
connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This technical bulletin provides a procedure to reprogram the power steering control module to correct a condition of...
Read full bulletin
Loss of Steering Assist due to a software abnormality.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary information communicates if the sunroof, rear sliding window, and/or wireless charging are found to be...
Read full bulletin
inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
Recovery Process from a Controller Reprogramming Interruption During service reprogramming of the T87 TCM, some...
Read full bulletin
technicians may notice the TCM may fail during the reprogramming event and become unresponsive to the Service Programming System (SPS), unresponsive to the GDS2 tool. This bulletin addresses corrective actions to attempt to recover the module before declaring the TCM as a bad part and replacing. During reprogramming, an interruption can cause the module to lock up. A module reset may recover the TCM
Malfunction Indicator Lamp Illuminated (MIL) - DTC P2635 and/or P018B Set In High Ambient Temperatures With Hesitation,...
Read full bulletin
Surging and Stalling Condition Some customers may comment that the Malfunction Indicator Light (MIL) is illuminated. Some customers may also comment on one or more of the following symptoms: Hesitation Surging Stalling Note: In ambient temperatures 100 F (37.7 C) degrees or higher, DTCs P2635 and/or P018B may set. The Technician may find one or more of the following DTCs set: P2635 P018B Cause This condition may be caused by a vapor buildup in fuel feed line. Correction If the conditions stated above are met, replace the fuel pump module with an updated version
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance...
Read full bulletin
that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
This service bulletin informs the technician to inspect for a possible electrical concern at the ECM X2 electrical...
Read full bulletin
connector to correct a customer concern of Malfunction Indicator Lamp (MIL) Illuminated - DTC P0333 Set.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground...
Read full bulletin
at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin explains to the technician that when using wiring repair labor operations,...
Read full bulletin
additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector...
Read full bulletin
sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.
This Preliminary information communicates an issue where the chassis wiring harness can chaff on the underbody of the...
Read full bulletin
vehicle causing a wide varied of issues,depending on which wire(s) is chaffed.Repair the affected wiring as needed
This Preliminary Information communication provides information to the technician about vehicles that may have a pop,...
Read full bulletin
click, tick, snap, or itch type noise in the steering column or steering wheel when turning left or right during low speeds or parking maneuvers. Technician will need to inspect for mis-routed airbag module wiring harness for contacting vibration damper plate in steering wheel, orreplace the column upper bearing inner race, spring, and seat.
This informational bulletin provides information on key code security rules and information on GM keycode look-up...
Read full bulletin
applications.
This SKU is a Fuel Pump Driver Module.
Read full bulletin
The customer communication requested return of unsold inventory to inspect the software. The software may have a fault where the readiness monitors are stuck in the not-ready or incomplete position. The readiness monitors will not cause performance or emissions issues but will prevent the emissions scanning tools from confirming the module is performing correctly, causing the vehicle to fail state required emissions tests.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
This technical bulletin provides a procedure for testing the battery cables for voltage drop, Checking for a bad ground...
Read full bulletin
at g218, Inspecting for a short at the starter B+ to shield and testing for a faulty battery.
This Preliminary information communicates if the sunroof, rear sliding window, and/or wireless charging are found to be...
Read full bulletin
inoperative due to the F2DL and/or the F8DL fuse(s) being open. Inspect the center console harness area at the hinge pivot point for chaffed circuits.
This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up.
Read full bulletin
Thisinformation advises dealers on how the seat functions and alsoa common area where an open circuit may be found between the third row seat module and the seat position sensor.It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well asadvising the dealer to look for bent/damaged seat recline mechanisms.
This Preliminary Information communication provides information to the technician about vehicles that have "ADAPTIVE...
Read full bulletin
CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician should consider environmental factors, repair, collision, aftermarket parts, and radar alignment factors. For Cadillac Escalades model years 2015-2017 in a barren environment, technician will need to update the Long Range Radar module with the latest software available in Tis-2-Web.
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part...
Read full bulletin
Number in eSI and how to locate the part(s) in the EPC.
This Preliminary Information communication provides information to the technician about vehicles that may have any of...
Read full bulletin
these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper inoperative, and or a dead battery. Technician may find Diagnostic Trouble Codes B3101, B144C, C0710, C0544, U1548, U1549, U154A, U0151, U0126, U0415, U0077, U0028 and/or U0029. Technician should inspect the left instrument panel for the wire harness being pinched. Technician will need to repair the wire harness and reroute the wire harness.
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance...
Read full bulletin
that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
This Preliminary Information communication provides information to the technician for the adaptive cruise control or...
Read full bulletin
lane keep assist unavailable message in the driver?s information center after the vehicle has been parked in direct sunlight and high ambient temperatures. The cameras electronic control unit?s internal operating temperature range is -40 degrees Celsius to 85 degrees Celsius. If the temperature of the electronic control unit of the camera module exceeds 85 degrees Celsius the image processor will no longer function resulting in adaptive cruise control and lane keep assist to be unavailable until the temperature falls to below the maximum operating temperature range
This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector...
Read full bulletin
sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This Preliminary Information communication provides information to the technician about vehicles that have "Service 4...
Read full bulletin
Wheel Drive" message on the Driver Information Center. Provides the technician with additional information to ensure that the TCCM contains the latest software released to address previous issues, also advises of default action changes. Calls out specific circuits to be inspected to help isolate intermittent codes.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
15086A - Customer Satisfaction Program.
Read full bulletin
On certain passenger cars and light duty trucks, equipped with Gen 10 OnStar, the embedded phone flash memory chip may become corrupted, causing the OnStar system to become inoperative. Dealers are to replace and program the vehicle communication interface module (VCIM).
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive...
Read full bulletin
finish".
This Preliminary Information communication provides information to the technician the steps to diagnose and repair...
Read full bulletin
vehicles that may have an Object Detection System Message Diagnostic Trouble Codes U0075, U026A, U026B, U026C, U0265, U0268, and/or U0269 stored in the active safety module. Technician should inspect his Multiple Diagnostic Interface cable for damage. Technician should use the Multiple Diagnostic Interface on a like vehicle with object detection bus or theEL-47955-1 MDI 1, MDI 2 Self-Test Loopback Adapter,if there are no issues found finish with diagnosing the customer’s concern, if concern is present in the like vehicle replace the Multiple Diagnostic Interface cable.
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about the Media Oriented Systems...
Read full bulletin
Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
This technical bulletin provides a procedure on how to turn the transport mode message of and reset the battery light...
Read full bulletin
flashing.
This preliminary informational bulletin provides a procedure for the technician to test the power seats, the outside...
Read full bulletin
power mirriors, shorts in the wiring and the MSM, and reprogram the module if shorts weren't found, for the customers concern of the mirriors and/or seat inoperative.
This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance...
Read full bulletin
that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up.
Read full bulletin
Thisinformation advises dealers on how the seat functions and alsoa common area where an open circuit may be found between the third row seat module and the seat position sensor.It provides repair instructions if a concern is found with the circuits between the third row folding seat module and the seat back position sensor, as well asadvising the dealer to look for bent/damaged seat recline mechanisms.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate it from the mount. The instrument panel accessory bezel will also need to be removed. Apply flocking tape to the instrument panel accessory bezel retainers. Also the instrument panel extension will need to be removed. Apply foam tape around connectors located under grill to prevent them from rattling on grill. Apply flocking tape to the instrument panel extension retainers and apply a strip of foam tape along the edge of the grill to isolate the grill from the dash.
This Preliminary information communicates to the technician when diagnosing intermittent circuit concerns to look at the...
Read full bulletin
connector for missing weather pack seals that could allow water intrusion into the connector and lead to corrosion on the terminals.
This Preliminary Information communication provides information to the technician about vehicles that have "ADAPTIVE...
Read full bulletin
CRUISE TEMPORARILY UNAVAILABLE" message on the Driver Information Center when attempting to activate the cruise. Technician should consider environmental factors, repair, collision, aftermarket parts, and radar alignment factors. For Cadillac Escalades model years 2015-2017 in a barren environment, technician will need to update the Long Range Radar module with the latest software available in Tis-2-Web.
This Preliminary Information communication provides information to the technician about vehicles that have a...
Read full bulletin
“Service 4WD Message” displayed in the Driver Information Center. Technician may find Diagnostic Trouble Codes C0392 or C0396. Technician should check the terminal tension on the Transfer Case Control Module X1 connector. Technician should repair any terminal that have poor terminal tension.
This Preliminary Information communication provides information to the technician on how to tell the difference between...
Read full bulletin
the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
This Preliminary Information communication provides information to the technician the steps to diagnose and repair the...
Read full bulletin
concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating. Once the display starts to update it may take several more minutes of driving above 20 mph for the display to fully update. Also if the vehicle is shut off for more than 8 hours the display will update when the ignition is turned on.
Transmission
83 bulletinsThis PI communicates the proper part numbers for transmission connectors and internal harness to prevent confusion when...
Read full bulletin
ordering
This PI communicates the proper part numbers for transmission connectors and internal harness to prevent confusion when...
Read full bulletin
ordering
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and...
Read full bulletin
repair of 8 Speed Transmissions
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed...
Read full bulletin
engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
This Preliminary information communicates for Technicians installing a Service Replacement Transmission Assembly to...
Read full bulletin
contact Technical Assistance to make sureunit is not suspect of a snap ring concern prior to installation.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This Preliminary information communicates diagnostic information for vehicles with transmission noise.
This Preliminary information communicates diagnostic information for vehicles with transmission noise
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary information communicates to have the dealer contact TAC with the transmission TUN number prior to...
Read full bulletin
transmission installation.
This Preliminary information communicates Diagnostic aids for a no start or DTC'S following a transmission replacement
Information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts
Information on Transmission Adaptive Functions
This bulletin advises the technician that the 6L50 (MYB), 6L80 (MYC) and 6L90 (MYD) Transmission Oil Filter and Seal Kit...
Read full bulletin
part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold individually.
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First...
Read full bulletin
Start Up/Shift of the Day Under Light Throttle.
8-speed Transmission Harsh Shift
Unwanted Grade Braking - Low Power - And/Or Transmission Busy Shifting.
Information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts
Information on Transmission Adaptive Functions
This Preliminary Information communication advises the technician on diagnostic aids to help with the diagnosis and...
Read full bulletin
repair of 8 Speed Transmissions
Electric Power Steering Gear Has Ended.
Electric Power Steering Gear.
This information bulletin advises the technician the difference between a welch cap leak and the output seal of the...
Read full bulletin
t-case or transmission leaking ATF, causing the customer concern of a Red Fluid Leak from Center of Vehicle Located by Rear of Transmission or Transfer Case Area.
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First...
Read full bulletin
Start Up/Shift of the Day Under Light Throttle.
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This information advises the technician the difference between a welch cap leak and the output seal of the t-case or...
Read full bulletin
transmission leaking ATF causing the customers concern.
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed...
Read full bulletin
engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This informational bulletin explains how the trans slip or flare can be a normal condition.
This informational bulletin advises the technician of possibly installing the incorrect 1-2-7-8-R clutch fluid passage...
Read full bulletin
seal and which seal should be used with measurements of the seal.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This service bulletin provides service /diagnostic information to aid with a Transmission Harsh 1-2 Shift Upon First...
Read full bulletin
Start Up/Shift of the Day Under Light Throttle.
This service bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts,...
Read full bulletin
Slips, or Flares.
This technical bulletin provides a procedure to clear the codes and test the Tcase if found that the customer has tried...
Read full bulletin
to shift the t-case from 4lo to Hi gears while driving.
This Preliminary Information communication provides information to the technician about being to achieve pre-load when...
Read full bulletin
setting up the pinion bearing pre-loads during reassembly of the 9.5/9.76 inch rear axles. Technician will need to use pinion gear install washer part number 11609638 onto the pinion shaft between the flange and nut. Tighten the pinion nut until you achieve 10 pound inch or 1.0 newton rotating torque. After the torque has been achieved back the nut off and remove the washer. Tighten the nut back down until you achieve 15 pound inch or 1.7 newton meters for used bearings or 20 pound inch 2.25 newton meters for new bearings.
Special Coverage. Some vehicles may have a condition where thermal cycling on the combination transmission fluid/oil...
Read full bulletin
and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
On some 2015-2017 model year Cadillac Escalade, Escalade ESV, Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL...
Read full bulletin
vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance
This informational bulletin advises the tech of a possible normal condition when the vehicle creeps forward during start...
Read full bulletin
up conditions when the clutch packs are full of residual oil.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin provides information on Transmission Adaptive Functions and Correcting Low Mileage Harsh...
Read full bulletin
Shifts, Slips, or Flares.
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been...
Read full bulletin
repaired for the flare and its still noticed.
Special Coverage (Parts Ordering Information Added).
Read full bulletin
On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.
Special Coverage (Diagnosis Time Added).
Read full bulletin
On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.
This Preliminary Information communication provides information to the technician about vehicles that may have a delayed...
Read full bulletin
engagement into drive, shudder at a launch, or the transmission is slipping when shifting into 1st, 2nd, 3rd or 4th gears. This may be due to loose stator support to pump cover bolts causing a leak at the stator support to pump cover gasket. Technician will check for the bolts to be loose. If any of the bolts are loose or the gasket is misaligned or leaking, the transmission pump cover must be replaced and the 1234 clutch plates should be inspected for being distressed and repaired as needed.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This informational bulletin explains possible normal condition of a flare from 1st to 2nd, even if the trans had been...
Read full bulletin
repaired for the flare and its still noticed.
17336 05 - Special Coverage.
Read full bulletin
On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. This special coverage covers the condition described above for a period of 5 years or 60,000 miles (100,000 km) for Chevrolet Suburban, Tahoe, GMC Yukon and Yukon XL and 6 years or 72,000 miles (116,000 km) for Cadillac Escalade and Escalade ESV, whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.
N192217820 - Service Update Bulletin.
Read full bulletin
The current transmission fluid may cause the customer to experience a shake or shudder feeling, which may be described as driving over rumble strips or rough pavement. Dealers are to drain the old transmission fluid and refill with the new fluid.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This technical bulletin provides information for new transmission oil to use, a procedure for exchanging the old fluid...
Read full bulletin
and adding the new fluid to a service transmission.
This preliminary informational bulletin adds the 2016 model year to diagnostic tips and repair information to correct a...
Read full bulletin
customer concern of reduced acceleration at low speed and/or transmission slipping from a launch, DTC P0751 set.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This informational bulletin provides normal operating characteristics and diagnostic information on Manual...
Read full bulletin
transmissions.
This technical bulletin provides information for new transmission oil to use and a procedure for exchanging the old...
Read full bulletin
fluid and adding the new fluid to correct a shake/shudder during light throttle acceleration condition.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This technical bulletin provides a procedure to flush and drain fluids for the transmission to eliminate a shake and/or...
Read full bulletin
shudder during a light throttle acceleration between 40 and 128 KM/H (25 and 80 MPH) at a steady state.
This Preliminary Information communication provides information to the technician to refer to bulletin 16-NA-175 to aid...
Read full bulletin
in addressing torque converter clutch shudder concerns.
This Preliminary Information communication provides information to the technician to refer to bulletin 16-NA-175 to aid...
Read full bulletin
in addressing torque converter clutch shudder concerns.
17336 04 - Special Coverage (Warranty Information Revised).
Read full bulletin
On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. Dealers are to inspect the air conditioning condenser and replace if necessary. The repairs will be made at no charge to the customer.
This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic...
Read full bulletin
transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low operation.
Body & Paint
63 bulletinsThis PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame...
Read full bulletin
Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.
This PI Communications information on an alternative product dealers can use to perform 19-NA-255: Wax Coating on Frame...
Read full bulletin
Peeling, Metal Shows Corrosion/Rusting due to issue with getting product from current supplier listed in the bulletin.
This preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This service bulletin provides frame coating repair information to correct a customer concern of wax coating on frame...
Read full bulletin
peeling, metal shows corrosion/rusting (U.S. and Canada Only).
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the...
Read full bulletin
shipping film.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting.
Wax Coating on Frame Peeling, Metal Shows Corrosion/Rusting.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
Sunroof Reverses When Closing At Highway Speeds.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
Illuminated Door Handles
Power Liftgate Inoperable
Wind Buffeting Droan Type Noise And/Or Body Pressure Booming.
Wind Buffeting Droan Type Noise And/Or Body Pressure Booming.
Wind Buffeting Droan Type Noise And/Or Body Pressure Booming.
This service bulletin provides information on Paintless Dent Repair Process.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint...
Read full bulletin
percentage.
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and...
Read full bulletin
that it is considered a normal condition.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This Preliminary Information communication advises the technician that the door striker cover will be shipped with the vehicle from the assembly plant.
Read full bulletin
Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
This Preliminary information communicates if the liftglass will not open using keyless entry to verify Valet Mode is not...
Read full bulletin
enabled.
This technical bulletin provides a procedure to pry the upper and lower quarter rear trim panel sheet metal apart to...
Read full bulletin
eliminate a creak noise heard from the quarter lower rear trim panel area.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This informational bulletin provides diagnostic/inspection information for the air box and air filter seal to correct a...
Read full bulletin
MIL and DTCs P0420 and P0430 setting.
This Preliminary Information communication advises the technician that the door striker cover will be shipped with the vehicle from the assembly plant.
Read full bulletin
Technician is to make sure the rounded side of the cover is positioned towards the outboard side of the vehicle.
This preliminary information communicates an issue with the floor center console sliding compartment door broken and how...
Read full bulletin
to repair it without replacing the complete floor center console assembly.
This preliminary informational bulletin provides frame coating repair information to correct a customer concern of wax...
Read full bulletin
coating on frame peeling, metal shows corrosion/rusting (U.S. and Canada Only).
This preliminary information communicates an issue with thefloor center console sliding compartment door broken and how...
Read full bulletin
to repair it without replacing the complete floor center console assembly.
This Preliminary Information communication provides information to the technician about vehicles that may have a whistle...
Read full bulletin
noise in the vehicle from the driver or passenger side. Technician will need to inspect for voids in the body sealer on the left or right side A-pillar. Technician should also inspect for voids in the body sealer at the cowl seam and apply sealer as necessary.
This preliminary bulletin provides information and a procedure for repairing rusted frames caused by the wax coating...
Read full bulletin
peeling off.
This Preliminary information communicates if the liftglass will not open using keyless entry to verify Valet Mode is not...
Read full bulletin
enabled.
This Preliminary Information communication provides information to the technician about vehicles thatmay have Service...
Read full bulletin
Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view camera and ensure the camera is properly mounted.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication provides information to the technician on a concern of wind buffeting noise...
Read full bulletin
and/or water leak.Technician is to follow the steps to apply vibration control material between the sunroof roof bow and the roof sheet metal.
Fuel System
38 bulletinsThis informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for...
Read full bulletin
analysis.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
Tiny Rattle And/Or Buzz Noise From Rear Of Vehicle (Inspect Exhaust Heat Shield)
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable...
Read full bulletin
diesel fuel.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This information bulletin advised the tech of possible use of low fuel quality and the possible ramifications in...
Read full bulletin
performance in regards to the customers concerns.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the...
Read full bulletin
part and ordering it from the EPC.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This technical bulletin provides a procedure to replace both fuel feed lines for a leak and/or noise coming from pulses...
Read full bulletin
in the fuel line.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This Bulletin provides information for rebuilding fuel injectors in the event of an underhood fuel odor and/or extended...
Read full bulletin
cranking condition.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This technical bulletin provides a procedure to replace both fuel feed lines for a leak and/or noise coming from pulses...
Read full bulletin
in the fuel line.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks...
Read full bulletin
using the evaporative emission cart smoke machine and ultrasonic leak detectortools.
This informational bulletin provides information on top tier fuels and what brands are available.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
Brakes
23 bulletinsThis service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
Dome Lamps Flash On And Off When Operating Brake Pedal Or Turn Signal.
Normal Characteristic - No Remote Detected / Place Key in Transmitter Pocket/Press Brake To Restart DIC Messages
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This technical bulletin provides repair information to correct a customer concern of pulsing, grinding, scraping noise...
Read full bulletin
from brakes, uneven front brake pad wear.
This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications
This technical bulletin provides a procedure to add PET tape to the brake cables if the cause of the customers concern.
This technical bulletin provides a procedure to add PET tape to the brake cables if the cause of the customers concern.
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly...
Read full bulletin
abrasive disk on gasket sealing surfaces or reused parts.
This technical bulletin provides a procedure to add PET tape to the brake cables if the cause of the customers concern.
This technical bulletin provides repair information to correct a customer concern of pulsing, grinding, scraping noise...
Read full bulletin
from brakes, uneven front brake pad wear.
This technical bulletin provides repair information to correct a customer concern of pulsing, grinding, scraping noise...
Read full bulletin
from brakes, uneven front brake pad wear.
This Preliminary information communicates the location of the GM Accessory Performance Brake System Rotor Specifications
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk...
Read full bulletin
on gasket sealing surfaces or reused parts.
This Preliminary Information communication provides information to the technician about customers that may request the...
Read full bulletin
factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.
This Preliminary Information communication provides information to the technician about customers that may request the...
Read full bulletin
factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.
Infotainment
23 bulletinsRadio Inoperative with No Communication and DTC U0184
Radio Does Not Display The Correct Song When Listening To An Ipod.
XM Audio Traffic And Travel Link Availability And Operation.
HD Radio Turns On Unwanted When Using Radio Station Voice Command.
Infotainment System Will Not Return to Media After Bluetooth Call Ends
Navigation Voice Prompts Choppy Distorted or Garbled.
Touch Screen Inoperative / No Audio.
Touch Screen Inoperative / No Audio.
Touch Screen Inoperative / No Audio.
Call Screen Is Still Displayed After Ending A Bluetooth Call
Information On Requests To Add OnStar Bluetooth Option.
Radio Touchscreen Inaccurate or Difficult To Use.
Possible Blank Radio Display.
This Preliminary Information communicates diagnostic tips for a condition of No GPS location on Radio.
This technical bulletin provides repair information to correct a customer concern of Loss of Radio Audio Shortly After...
Read full bulletin
an OnStar In-Vehicle Voice Message Is Heard.
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar.
Read full bulletin
Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some...
Read full bulletin
SiriusXM Channels Due to Interference in Some Geographic Locations.
This Preliminary Information communication provides information to the technician about vehicles that the Navigation...
Read full bulletin
radio does not have a global positioning system location but OnStar is able to accurately locate the vehicle. Technician should check the installation of the COAX cables to be router correctly. Technician will gain access to the Radio or Human Machine Interface depending on the vehicle build. Install the EL-50334 test antenna to the Radio HMI and evaluate the operation. If the GPS signal is restored, inspect for incorrect coax routing as described above and if found, reroute the cable so it does not bypass the splitter.
This technical bulletin provides repair information to correct a customer concern of Audio Muting When Listening to Some...
Read full bulletin
SiriusXM Channels Due to Interference in Some Geographic Locations.
This Preliminary information communicates repair information for therear vision camera or surround vision camera image...
Read full bulletin
being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
This informational bulletin provides the technician on what to do if the customer has a navagation concern and submit a...
Read full bulletin
feedback form to the GM navigation disc center website.
This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar.
Read full bulletin
Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
This Preliminary Information communication provides information to the technician about vehicles that may have an issue...
Read full bulletin
when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
Lighting
22 bulletinsThis preliminary information communicates an issue with aftermarket LED headlights causing IPC warning messages and MIL...
Read full bulletin
along with several low speed lan DTCs.
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary information communicates to dealers of a known issue with failed map update
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
SHAKE AND/OR SHUDDER DURING LIGHT THROTTLE ACCELERATION BETWEEN 40 AND 128 KM/H (25 AND 80 MPH) AT A STEADY STATE.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and...
Read full bulletin
the Proper use of GM Simplified Maintenance Schedules.
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During...
Read full bulletin
Warranty Coverage Period.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps...
Read full bulletin
will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits disabling daytime running lamps (DRL's) or auto headlamps.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
Tires & Wheels
22 bulletinsThis service bulletin provides information on Tire Sidewall Irregularities.
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM...
Read full bulletin
Vehicles.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
Refinishing Aluminum Wheels
Refinishing Aluminum Wheels
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance,...
Read full bulletin
Shake, Flat Spotting) of GM Original Equipment Tires.
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for...
Read full bulletin
GM Vehicles.
This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts...
Read full bulletin
when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This informational bulletin provides information for 22" accessory wheel/tire usages.
This Preliminary Information communication advises the technician to install the front wheel opening push pins during...
Read full bulletin
the pre-delivery inspection.
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
This Preliminary Information communication advises the technician to install the front wheel opening push pins during...
Read full bulletin
the pre-delivery inspection.
HVAC & Climate
17 bulletinsThis service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold...
Read full bulletin
weather climates and testing those batteries.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
Service Update for Inventory and Customer Vehicles Inspect Air Conditioning Refrigerant Warning Label and Adjust...
Read full bulletin
Refrigerant Charge
Inspect Air Conditioning Refrigerant Warning Label
A/C Blows Warm During High Ambient Temperatures.
A/C Blows Warm During High Ambient Temperatures.
A/C Blows Warm During High Ambient Temperatures.
Rear A/C Blows Warm Air.
Rear A/C Blows Warm Air.
A/C Blows Warm Or Poor Performance.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative...
Read full bulletin
and/or Insufficient Cooling due to the seals going bad within the part.
This technical bulletin provides a procedure to reinstall the rear defroster tab on the rear window defogger for...
Read full bulletin
vehicles with the condition of rear defrosters inoperative or if one is to break during a normal repair.
This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative...
Read full bulletin
and/or Insufficient Cooling due to the seals going bad within the part.
This technical bulletin provides a procedure to reinstall the rear defroster tab on the rear window defogger for...
Read full bulletin
vehicles with the condition of rear defrosters inoperative or if one is to break during a normal repair.
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS)...
Read full bulletin
concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
This technical bulletin provides a procedure to reinstall the rear defroster tab on the rear window defogger for...
Read full bulletin
vehicles with the condition of rear defrosters inoperative or if one is to break during a normal repair.
Air Bags & Safety
12 bulletinsThis service bulletin provides information on regular inspection of the Seat Belt Lap Anchor.
Passenger Airbag Partial Deployment
Passenger Airbag Partial Deployment
Passenger Airbag Partial Deployment
Passenger Airbag Partial Deployment
Passenger Airbag Partial Deployment
Passenger Airbag Partial Deployment
Passenger Airbag Partial Deployment
Passenger Airbag Partial Deployment
This service bulletin provides information on availability for a seat belt extender.
This Preliminary Information communication provides information to the technician for a water leak in in the second and third row seating area.
Read full bulletin
Inspect the C-pillar which is the body verticalstructure behind the rear passenger doorarea of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.
This Preliminary Information communication provides information to the technician for a water leak in in the second and third row seating area.
Read full bulletin
Inspect the C-pillar which is the body verticalstructure behind the rear passenger doorarea of the affected side of the vehicle for water intrusion or water marks on the seat belt retractor. If water evidence is found on the seat belt webbing or the retractor the seat belt/ retractor must be replaced after the water leak has been corrected and verified. There are 3 areas of seam sealer that will need to be addressed. After gaining access to the C-pillar and rear quarter panel area inspect for voids or missing seam sealer and apply a clear flow able seam sealer where needed.
Suspension
9 bulletinsThis service bulletin advises the tech to only replace the shock that is bad and not all shocks.
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair...
Read full bulletin
vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
Clunking Noise from Front of Vehicle During Turns and/or Bumps Some customers may comment on a clunking noise...
Read full bulletin
originating from the front of the vehicle that is more predominant during turns or traveling over bumps. This may be caused by a damaged stabilizer shaft frame bracket. There have been some cases in which the bracket is cracked, as shown. This condition has been found to be the result of insufficient welds between the bracket and frame rail. There have been some cases on older vehicles of corrosion affecting the bracket
This informational bulletin advises the tech to only replace the shock that is bad and not all.
This Preliminary Information communication provides information to the technician about vehicles that have a creak,...
Read full bulletin
click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair...
Read full bulletin
vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
This Preliminary Information communication provides information to the technician on the steps to help diagnose and...
Read full bulletin
repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair...
Read full bulletin
vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair...
Read full bulletin
vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer the conditions noted may not be covered under warranty. Technician will inspect for installed aftermarket suspension components. Also inspect for improperly adjusted torsion bars.
Software & Calibration
6 bulletinsThis service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
Recovery Process from a Controller Reprogramming Interruption
OnStar Voice Fallback Number Update
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
Steering
4 bulletinsPower Tilt and Telescoping Steering Column Does Not Recall With Memory Functions.
Driver Steering Wheel Airbag Not Flush With Steering Wheel and/or Difficulty Depressing Airbag to Engage Horn
Steering Column Grind Pop Bind Noise And/Or Feeling When Turning
Driver Steering Wheel Airbag Not Flush With Steering Wheel and/or Difficulty Depressing Airbag to Engage Horn.
Hybrid & EV
3 bulletinsThis service bulletin provides information on AGM batteries that require less frequent charging in storage.
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
This technical bulletin provides a procedure to replace the GEN I charging system with a GEN II charging system only if...
Read full bulletin
vehicles apply within the settings.