2006 Cadillac Escalade Ext TSBs

trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.

severe internal engine damage.

concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.

severe internal engine damage.

vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.

General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.

that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.

various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.

or engines during there break in period.

cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.

vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first hour of engine run time to allow break-in of the catalytic converter. Technician will need to use a Tech2 to check the verify engine run time on the Engine Hour Meter in the Instrument Panel Cluster Data Display/Data 1 List in the scan tool match. If the engine run time is less than one hour, the battery may have been disconnected, or another vehicle power loss event may have occurred, during vehicle manufacturing. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle. If the catalytic converter was replaced and the Diagnostic Trouble Codes set it may be a result of the engine run time restrictions no longer being in place since the vehicle is no longer new. Technician will need to clear the Diagnostic Trouble Codes and perform a drive cycle.

IN RARE CASES, CUSTOMERS MAY COMMENT ON A LACK OF STEERING ASSIST WHEN STOPPED OR DURING PARKING LOT TYPE OF MANEUVERS. *JS UPDATED 09/02/14*LJ

INOPERATIVE AND MAY STILL BE INOPERATIVE AFTER KEY IS TURNED ON. *PE UPDATED ON 5/1/12. *JS

*KB

regarding the differences of the Dexos oils.

find growing concerns around them.

and Canada only).

for causing multiple customer concerns that do not have other diagnostic methods to identify them.

Dealers Only).

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 miles per hour at any given speed when looking straight at the needle.

availability of the passenger compartment air filter. Dealer should advise the customer starting in 2003 the passenger compartment air filter is no longer available as a factory option.

Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.

TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS.

*TT

*TT

*TC *SC

This communication is to return unsold inventory because some product sold in 2016 may not have coil harness wound in a centered condition as an assembly aid. If installer does not center the rotations of the assembly during replacement process in accordance with applicable AllData service and repair procedure, post-install turning of the steering wheel will trigger the air bag warning light of the vehicle.

it is imperative that all related terminal pin fit and tension be checked when the test steps require disconnection of the connector or component, prior to any component replacement. Always use the recommended terminal test tool during these tests.

Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down, remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.

override the automatic door locking feature. Technician will update the Body Control Module on 2006 to 2007 model years. On 2010 to 2014 model years technician will need to contact Techline Customer Support for calibrations.

Communication Interface Modules (VCIM) (GMNA Only)

MODEL YEARS 2006-2011. DOES NOT APPLY TO VEHICLES WITH KEYLESS ACCESS SYSTEM. *PE

THIS CONCERN COULD BE CAUSED BY BROKEN SEAT POSITION SENSOR CIRCUITS UNDER THE DRIVER OR PASSENGER FRONT SEATS. OVER TIME, FROM REPEATED SEAT MOVEMENT, THE WIRING COULD BREAK. *PE

*KB

*KB

*KB

essential tool J-45096 TransFlow.

Technician should be advised that the maximum pinion shim to be used or stacked behind the pinion is 0.050?, and the minimum pinion shim is 0.020? for an 8.6 axle. The range for available pinion depth shims for the 10.5? axle is 0.006? to 0.024?. When setting the backlash it should be set between 0.003? to 0.005? on a new ring and pinion for any American Axle Manufacturing application. The ring and pinion can be reused or adjusted if the mileage is less than 500 miles, if not used for towing. Technician should be advised that a ?roller coaster? or ?hourglass? pattern on the bearings may be normal up to 10,000 miles and possibly longer. With a mis-machined housing you may get a heel pattern on both sides of the gear teeth at build up can generally be corrected with backlash adjustments. When setting up an 8.6? axle with a 5 cut gear set is to use a 0.035? pinion shim and set backlash to 0.004?. When using the newer 2 cut gear set also use a 0.035? pinion shim and still set backlash to 0.004?. To set the gear pattern use backlash to adjust the pattern heel to toe. Use the pinion shim to adjust the height of the pattern. The proper drive pinion bearing pre-load is from 15 - 30 inch pounds with new bearings. The total torque to turn after the differential case is installed should increase 5 - 10 inch pounds at the pinion. A new pinion nut must be used whenever the old one is removed. The axle shaft end play specification is 0.012? per side and the radial specification is 0.002? - 0.003?. Technician should be advised that synthetic lube can be used in all new American Axle Manufacturing axle assemblies. The new pinion seal for the 8.6? axle assembly is a two piece design.

forward ranges immediately after replacing the input housing. Technician will inspect the 3-4 clutches and the forward clutch oil feed passages for leakage between circuits. Technician should apply regulated compressed air to the 3-4 clutch feed hole and the forward clutch feed hole one at a time with the input housing. Technician will need to replace the input housing if there is an air leak 3-4 clutches.

protection or tint offered by the windshield or side glass. Technician should be advised Windshield reduces Ultraviolet rays down to 4% or less. Front side door glass reduces Ultraviolet rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.

or tint offered by the windshield or side glass. Technician should be advised Windshield reduces UV rays down to 4% or less. Front side door glass reduces UV rays down to 35% or less. Windshields are SOLAR glass with a light transmittance of >/=70%. Front door glass are Solar glass with a light transmission of >/=70%. Rear door glass, quarter windows and back windows can use either Solar glass (>/=70%) or Privacy glass, which has a light transmittance of 20%.

DO NOT REPLACE ENTIRE STEERING GEAR FOR PITMAN SEAL LEAK. TECHNICIANS HAVE BEEN REPLACING ENTIRE STEERING GEARS DUE TO NOT BEING ABLE TO SERVICE JUST LEAKING PITMAN SHAFT SEAL. *PE UPDATED 5/9/11. *PE

ALL 2000-2006 LIGHT DUTY TRUCKS EQUIPPED WITH THE LIGHT DUTY AUTOMATIC TRANSMISSION. *PE

balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)

Program and Global Warranty Management (GWM) Submission Information.

management submission information.

*TT UPDATED 08-15-07. *KB

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

While in the United States they are unable to receive Turn-by-Turn directions. Due to the existing cellular provider not having roaming agreements in areas outside of Canada to support transmitting of the packet data required for Turn-By-Turn feature to operate. The customer has 3 options while traveling through the United Sates. First if the vehicle is equipped with a navigation radio they can request a "Destination Download" to the vehicle. Second if the customer uses the OnStar RemoteLink app they can send the directions to the vehicle. The third option would be to have the vehicle loaded with a "500 phone number" The customer will no longer be able to use their Hands Free Calling minutes when the new 500 phone number is loaded. If a customer chooses to restore Hands Free Calling in the future a new phone number will be assigned to the vehicle; previous phone numbers are not available.

when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.

repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a "Phone Unavailable" audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A "Ready" or "OnStar ready" audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ?push to talk? button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.

ARE AVAILABLE, EXCEPT REAR AXLE CROSSOVER PIPE. MODEL 1999-2007 SILVERADO, SIERRA, 2000-2006 ESCALADE MODELS, AVALANCHE, SUBURBAN, TAHOE, YUKON MODELS. *PE UPDATED 7/18/14. *PE UPDATED 12/9/14. *PE

(REGROUND EBCM GROUND). *KB

Operations and Customer Enthusiasm

tools that include consumable parts (U.S. Only).

only) for service operations.

labor operation numbers and how to submit CCND.

*RM UPDATED ON 5/2/2012. *KB

VEHICLE MAY EXHIBITS SOME SYMPTOM(S) AS DOOR LOCKS CYCLE WHILE DRIVING; INTERMITTENT NO START; SERVICE STABILITRAK DIC MESSAGE; SPEEDOMETER AND TACHOMETER FREEZE WHILE DRIVING. *PE

*TT

THIS INCLUDES 05 CHEVROLET GMC CADILLAC FULL SIZE TRUCKS AND UTILITIES. *EH ALSO INCLUDES AVALANCE, SILVERADO SUBURBAN TAHOE; GMC SIERRA, YUKON, DENALI, YUKON XL, DENALI XL. UPDATED 8/26/08. *PE UPDATED 5/9/11. *PE

flushing services and additives) and proper use of GM simplified maintenance schedules (Canada only).

*NJ

usage of E85 fuel in GM vehicles.

*PE

Technician should not replace the bearing for grease purge. Technician should be advised to not clean the purged grease from the area immediately on or adjacent to the seals because this grease provides additional protection. Technician should only replace the bearing if the seals show visible damage, bearing endplay is greater than 0.005" or 0.13mm, bearing exhibits rough rotation, or bearing exhibits abnormal noise.

HOSE, OR THE COMPRESSOR SELF TEST MAY BE INOPERATIVE. ALSO INCLUDED SUBURBAN LD MY 2001-2013, YUKON DENALI XL MY 2013, YUKON XL LD 2001-2013 *JS

*RM UPDATED 12/6/11. *PE

*NJ UPDATED 7/17/2008. *PE

belt warning light illumination, as well as difficulty latching and unlatching the buckle or the buckle release button sticking.

*PE