2015 Cadillac CTS-V TSBs
362 Technical Service Bulletins across 16 categories
Categories
Engine
98 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This informational bulletin advises the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides inspection/diagnosis/correction information on a cold start misfire and/or rough idle and...
Read full bulletin
DTC P0300 that may also be set.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
This bulletin updates the position of General Motors on refinishing aluminum wheels.
Read full bulletin
GM has determined that wheel refinishing under warranty will no longer be performed.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This bulletin provides a service procedure to reprogram the Chassis Control Module (CCM) on certain 2015 model year...
Read full bulletin
Cadillac ATS vehicles equipped with a 2.0L or 2.5L engine (LTG/LCV). The switchable engine mount calibration currently in these vehicles is not the intended calibration for the "Tour/ECO" vehicle modes. Operating the vehicle in the "Tour/ECO" mode could result in a poor ride quality (shake) on rough roads. This could also result in less life to the engine mounts. and subsequent fluid leakage from the mounts.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This informational bulletin advised the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides diagnostic aid information/procedures to perform inspections to determine if the engine...
Read full bulletin
needs to be replaced as opposed to just internal parts for knocking, rattle, squeak and/or squeal type noises from engine.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information for after installation of a replacement upper valve body, the transmission...
Read full bulletin
may have no Reverse and no 2nd gear.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint.
Read full bulletin
GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
OEM and Remanufactured Engine and Automatic Transmission/Transaxle Identification
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and...
Read full bulletin
repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015?0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that "mating" surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
This Preliminary Information communication provides information to the technician about vehicles that have low oil...
Read full bulletin
pressure, no oil pressure, and/or engine noise. Technician will need to replace the oil pump, flush the oil cooler lines.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
This Preliminary Information communication provides information to the technician about vehicles that may have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on. Technician may find Diagnostic Trouble Codes P0106 and P0506. Technician will inspect for a broken valve spring and replace as needed.
This Preliminary Information communication provides information to the technician that some vehicles may have a rattle...
Read full bulletin
coming from the turbo on a cold start. If the technician has verified the rattle noise when cold is from the turbocharger, and the noise is unforced, there is a revised part available for this concern.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and...
Read full bulletin
repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped.
This Preliminary Information communication provides information to the technician about vehicles that have an engine oil odor with no oil leaks found.
Read full bulletin
Technician will need to inspect for an external oil leak. Technician will need to ensure the oil level is correct. Technician will need to replace the rear main seal, if no oil leaks were found and the engine oil level is not over full.
This Preliminary Information communication provides information to the technician about vehicles that have a Service...
Read full bulletin
Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308. If published Service Information diagnostics does not isolate the cause of this concern technician should check for a worn camshaft lobe and/or lifter roller, a sticking valve, valve leakage, a broken valve spring, and a collapsed active fuel management lifter.
This Preliminary Information communication provides information to the technician on the steps need to diagnose and...
Read full bulletin
repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped
This Preliminary Information communication provides information to the technician on the steps need to diagnose and...
Read full bulletin
repair vehicles that may have stalling shudder and/or hard shifting into 1st gear or reverse vibration on launch (with excessive crankshaft end play). Technician will test to determine if the crank shaft end play is within specification 0.0015–0.0086 inch. If end play is found to be out of specification, remove engine and inspect for possible crankshaft thrust bearing and/or crankshaft for wear. Inspect thrust bearing for wear on one side and crankshaft on that “mating” surface. If the thrust bearing has three vertical channels worn off replace connecting rod bearings, main bearings, thrust bearing and crankshaft. If working on a Corvette the oil tank with lines and oil cooler are both required to be replaced if equipped.
44180 02 - Customer Satisfaction.
Read full bulletin
Certain vehicles may have key codes which were inappropriately handled by a third party which could increase the risk of vehicle theft. Dealers are to replace all applicable keys and lock cylinders with new key configurations.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE E92 ECM RESTRICTION PART NUMBER 12662034 WILL...
Read full bulletin
BE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS PRODUCT QUALITY CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO...
Read full bulletin
REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON STEPS TO PERFORM TO DETERMINE IF THE CUSTOMER'S...
Read full bulletin
BATTERY DRAIN CONCERN IS BEING CAUSED BY A KNOWN CONCERN WITH BLUETOOTH CALL TRANSFER OPERATION WHEN EXITING THE VEHICLE. IF THE CONCERN IS DUPLICATED AT THE DEALER WITH THE ONSTAR LED IS STILL GREEN AFTER THE VEHICLE IS TURNED OFF AND THE BLUETOOTH CALL WAS DISCONNECTED. DEALER SHOULD ADVISES THAT ENGINEERING IS AWARE OF THE CONCERN AND IS CURRENTLY INVESTIGATING THE ISSUE.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL...
Read full bulletin
TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE LOW OIL PRESSURE MESSAGE.
Read full bulletin
TECHNICIAN MAY ALSO FIND A DIAGNOSTIC TROUBLE CODE P0521 IN THE ENGINE CONTROL MODULE. TECHNICIAN SHOULD FOLLOW ALL PUBLISHED SERVICE INFORMATION DIAGNOSIS. WHEN USING A SCAN TOOL IF THE OIL PRESSURE IS LOW BUT THE OIL PRESSURE AT THE OIL FILTER HOUSING IS CORRECT, TECHNICIAN SHOULD INSPECT THE VALVE LIFTER OIL FILTER FOR DEBRIS/SLUDGE THAT COULD BE RESTRICTING OIL FLOW TO THE OIL PRESSURE SENSOR. TECHNICIAN SHOULD REMOVE THE VALVE LIFTER OIL FILTER AND CLEAN IT. IF THE VALVE LIFTER OIL FILTER CANNOT BE CLEANED REPLACE IT.
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER...
Read full bulletin
DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE...
Read full bulletin
GASKET SEALING SURFACES.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO CHECK THE CYLINDERS FOR DAMAGED PISTONS AND DETERMINE IF THE USE OF...
Read full bulletin
AFTERMARKET CALIBRATIONS OR PERFORMANCE PARTS MAY BE THE CAUSE.
If a vehicle comes into the dealership with a knock noise, seized engine, lower end squeak or squeal or any condition...
Read full bulletin
that you suspect a rod or main bearing failure.
Pre-Delivery & Maintenance
91 bulletinsThis service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may...
Read full bulletin
not pass California smog inspection or smog inspection in other states.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on proper use of floor mats.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This service bulletin provides information on proper use of floor mats.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON...
Read full bulletin
VEHICLES ORIGINATING/SOLD IN CANADA.
Other
39 bulletinsThis PI provides Diagnostics tips on how the LIN bus works and how to diagnosis it.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary information communicates the steps on how to save a GDS2 Session Log and upload to a Technical...
Read full bulletin
Assistance Case in CX Connect.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
New Vehicle Monitoring Programs Section in IVH
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Rear Vision Camera Appears Obstructed.
Identifying If A Vehicle Is Equipped With OnStar 4G LTE Wi-Fi.
Information on Driveline Clunk Noise
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
J-35616-64B Terminal Test Probe / Replacement Terminal / Terminated Lead.
Changing Turn-By-Turn Voice Response To Metric Or English Units
Information on Driveline Clunk Noise
Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
Canadian Customers Unable To Place Calls In The United States
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
Essential Tools that Include Consumable Parts (U.S.
Read full bulletin
Only)
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify...
Read full bulletin
the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
IPC Odometer Programming Method Quick Reference Guide
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PROPER USE OF FLOOR MATS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN.
Read full bulletin
THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF...
Read full bulletin
BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN.
Read full bulletin
THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES.
Read full bulletin
GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS...
Read full bulletin
LESS THAN 10,000 MILES ON IT.
Electrical
27 bulletinsThis Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use...
Read full bulletin
for certain repairs, such as Wiring Harness Repairs.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
Special Return - Fuel Tank Module Kit: ACDelco Part Number M10256 (select date codes)
High Voltage Safety ? High Voltage Disabling
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
OnStar Module Does Not Support All B101D Symptom Codes.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This service bulletin provides information on Module Harvesting.
IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1.
Read full bulletin
IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2 The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event.
15086A - Customer Satisfaction Program.
Read full bulletin
On certain passenger cars and light duty trucks, equipped with Gen 10 OnStar, the embedded phone flash memory chip may become corrupted, causing the OnStar system to become inoperative. Dealers are to replace and program the vehicle communication interface module (VCIM).
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF...
Read full bulletin
RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC...
Read full bulletin
DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A...
Read full bulletin
DEAD BATTERY AFTER LEAVING THE VEHICLE DURING A BLUETOOTH CALL.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION FOR IGNITION KEY, FOB, KEY TAGS AND KEY RINGS CONFIGURATION FOR VARIOUS...
Read full bulletin
VEHICLES AND APPLYING A QR CODE STICKER OR BARCODE STICKER TO THE FOB.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT ,WHEN TESTING ANY CIRCUIT FOR OPEN OR RESISTANCE,...
Read full bulletin
IT IS IMPERATIVE THAT ALL RELATED TERMINAL PIN FIT AND TENSION BE CHECKED WHEN THE TEST STEPS REQUIRE DISCONNECTION OF THE CONNECTOR OR COMPONENT, PRIOR TO ANY COMPONENT REPLACEMENT. ALWAYS USE THE RECOMMENDED TERMINAL TEST TOOL DURING THESE TESTS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF...
Read full bulletin
RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF A...
Read full bulletin
DEAD BATTERY AFTER LEAVING THE VEHICLE DURING A BLUETOOTH CALL.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO HELP THE DEALERSHIP TECHNICIANS PERFORM A PARASITIC...
Read full bulletin
DRAIN TEST FOR THE ONSTAR MODULE. WHEN PERFORMING BATTERY PARASITIC DRAIN TEST, THERE MAY BE SOME CONFUSION AS TO WHAT THE NORMAL POWER CONSUMPTION READING SHOULD BE FROM THE ONSTAR SYSTEM.
Body & Paint
20 bulletinsThis preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the...
Read full bulletin
shipping film.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides information on Paintless Dent Repair Process.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers.
Read full bulletin
Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN.
Read full bulletin
VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN.
Read full bulletin
VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON A NORMAL CONDITION ON TEMPERED GLASS OF SPOTS SHOWING ON THE REAR...
Read full bulletin
AND SIDE WINDOWS WHEN THE VEHICLE IS IN THE SUNLIGHT.
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES INFORMATION THAT MAY BE HELPFUL WHEN ADDRESSING UNDERBODY COMPONENT...
Read full bulletin
CORROSION WITH CUSTOMERS.
Tires & Wheels
18 bulletinsThis preliminary information communicates information about how to determine if a wheel and tires size change is...
Read full bulletin
available.
This service bulletin provides information on Tire Sidewall Irregularities.
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM...
Read full bulletin
Vehicles.
This service bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left or...
Read full bulletin
Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
Information on Removal/Cracking of Stainless Steel Wheel Nut Caps.
Refinishing Aluminum Wheels
Refinishing Aluminum Wheels
This service bulletin provides information on Characteristics of Wide Low Aspect Ratio Tires, Vehicle Pulls Left or...
Read full bulletin
Right, Wanders, Follows Depressions in Road Surface, Tramlining.
This service bulletin provides information on summer tire performance and tire cold weather cracking.
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information on summer tire performance and tire cold weather cracking.
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE RUBBER USED IN SOME PERFORMANCE TIRES LOSES FLEXIBILITY AND MAY...
Read full bulletin
DEVELOP SURFACE CRACKS IN THE TIRE TREAD/SHOULDER AREA AT COLDER TEMPERATURES.
Transmission
17 bulletinsThe service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This bulletin advises the technician that the 6L50 (MYB), 6L80 (MYC) and 6L90 (MYD) Transmission Oil Filter and Seal Kit...
Read full bulletin
part number 24236933 is currently transitioning from a kit to the filter (24236517) and seal (24225347) being sold individually.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while cruising at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This informational bulletin explains how the trans slip or flare can be a normal condition.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to first gear.
This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating.
Read full bulletin
The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle. This concern may also be present while crusing at highway speeds and then an aggressive increase in throttle.This is considered normal operation of the vehicle the throttle is delayed and opened slowly up to .7 seconds to help minimize driveline lash and clunking or will have approximately .5 seconds of zero torque to allow the transmission to shift to downshift.
THIS INFORMATIONAL BULLETIN PROVIDE INFORMATION ON THE OPERATING CHARACTERISTICS OF A MANUAL TRANSMISSION.
Infotainment
14 bulletinsXM Audio Traffic And Travel Link Availability And Operation.
Infotainment System Will Not Return to Media After Bluetooth Call Ends
Information On Requests To Add OnStar Bluetooth Option.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WITH THE STEPS NEED TO DIAGNOSE AND...
Read full bulletin
REPAIR VEHICLE THAT MAY HAVE A CONCERN WITH NAVIGATION ICON NOT SHOWING THE CORRECT LOCATION THEN JUMPING TO THE CORRECT LOCATION. THE POSITION INDICATOR MAY SHOW THE VEHICLE TURNING IN THE OPPOSITE DIRECTION OR MAY SHOW THE VEHICLE TRAVELING OFF THE ROAD. TECHNICIAN WILL INSPECT THE HUMAN MACHINE INTERFACE MOUNTING. FOLLOW SERVICE INFORMATION FOR THE CORRECT ORIENTATION OF THE HUMAN MACHINE INTERFACE.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A BLANK...
Read full bulletin
DISPLAYS, FLASHING DISPLAYS, ERROR OR UPDATE FAILED MESSAGES, NAVIGATION MAP NOT LOADING, BLUETOOTH OR USB CONCERNS. TECHNICIAN SHOULD INSPECT THE USB/SD CARD PORT FOR A SD CARD OR A DEVICE PLUG INTO ANY OF THE USB PORTS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER FOR FURTHER INSTRUCTIONS.
Read full bulletin
THE CONCERN IS THE RADIO MAY BE UNABLE TO SAVE XM FAVORITE STATIONS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN NOT TO MAKE ANY REPAIRS OR REPLACE ANY PARTS.
Read full bulletin
THE TECHNICIAN IS TO CONTACT THE GM TECHNICAL ASSISTANCE CENTER TO REVIEW A CONCERN WHEN THE VEHICLE'S RADIO IS UNABLE TO SAVE A XM PRESET AFTER SAVING PRESETS.
THIS PRELIMINARY INFORMATION COMMUNICATION IS TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER.
Read full bulletin
THE CUSTOMER IS UNABLE TO SELECT RADIO PRESETS FROM THE USB OR SD CARD AS THEY ARE GREYED OUT.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN.
Read full bulletin
THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN WHEN THE CUSTOMER COMMENTS THAT THEIR...
Read full bulletin
DIGITAL VEHICLE SPEED DISPLAY IS SHOWING A DIFFERENT SPEED THAN THE ANALOG VEHICLE SPEED DISPLAY. THERE MAY BE UP TO 2 MILES PER HOUR DIFFERENCE BETWEEN THE DIGITAL AND ANALOG VEHICLE SPEED DISPLAYS. THIS IS A NORMAL CONDITION DUE TO THE CALCULATION TOLERANCES BEING DIFFERENT FOR THE TWO DRIVER VIEWING ANGLES FOR THE ANALOG SPEEDOMETER; IT MAY ALSO APPEAR TO INCREASE THE DIFFERENCE BETWEEN BOTH DISPLAYS. NO PART REPLACEMENT IS REQUIRED AS THIS IS A NORMAL OPERATING CHARACTERISTIC OF THE VEHICLE. FOR CTS VEHICLES BUILT BETWEEN APRIL AND JUNE OF 2011 OR THE 2013 ATS, SRX, XTS BUILT BEFORE AUGUST 29 2012 MAY HAVE A 3 MILES PER HOUR OR MORE VARIATION. THE TECHNICIAN IS TO REPLACE THE INSTRUMENT PANEL CLUSTER FOR THIS CONCERN.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO...
Read full bulletin
VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE RADIO IS INOPERTIVE.
Read full bulletin
NEW SOFTWARE HAS BEEN RELEASED TO CORRECT THIS CONCERN.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN NOT TO REPLACE ANY PARTS AND TO CONTACT GM TECHNICAL...
Read full bulletin
ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER. VEHICLE'S RADIO DISPLAY MAY BE SLOW TO TURN ON WHEN STARTING THE VEHICLE IF THE DOORS WERE NOT LOCKED.
THIS PRELIMINARY INFORMATION COMMUNICATION IS TO CONTACT GM TECHNICAL ASSISTANCE CENTER TO REPORT THE CONCERN AND OBTAIN A CASE NUMBER.
Read full bulletin
THE CUSTOMER IS UNABLE TO SELECT RADIO PRESETS FROM THE USB OR SD CARD AS THEY ARE GREYED OUT.
Fuel System
10 bulletinsThis informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for...
Read full bulletin
analysis.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
Lighting
9 bulletinsThis informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This service bulletin provides repair procedures, depending on model year, to correct a customer concern of a...
Read full bulletin
Malfunction Indicator Lamp (MIL) Illuminated with DTC P0172, P06DE and/or P0521 Set.
SHAKE AND/OR SHUDDER DURING LIGHT THROTTLE ACCELERATION BETWEEN 40 AND 128 KM/H (25 AND 80 MPH) AT A STEADY STATE.
Brakes
6 bulletinsThis service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This Preliminary Information communication provides information to the technician abut vehicles that have excessive amount of brake dust on the wheels.
Read full bulletin
Dealer should advise the customer this is a normal characteristic of the performance race pads that are installed on the vehicle, and to reference the owner?s manual for cleaning instructions.
HVAC & Climate
5 bulletinsPI to help diagnose A/C concern
This service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold...
Read full bulletin
weather climates and testing those batteries.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
A/C Blows Warm Or Poor Performance.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
Software & Calibration
3 bulletinsThis service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
OnStar Voice Fallback Number Update
Hybrid & EV
2 bulletinsThis service bulletin provides information on AGM batteries that require less frequent charging in storage.
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
Air Bags & Safety
2 bulletinsThis service bulletin provides information on availability for a seat belt extender.
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS...
Read full bulletin
REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
Steering
1 bulletinTHIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE CONDITION IS A NORMAL OPERATING CHARACTERISTIC OF THEIR VEHICLE.
Read full bulletin
A CUSTOMER MAY COMMENT THAT THEY FEEL A STEERING BIND CONDITION WHEN THE CAR IS IN REVERSE, OR DRIVING FORWARD AND THE STEERING WHEEL IS TURNED AT OR NEAR THE FULL-LOCK POSITION.