2017 Buick Cascada TSBs
881 Technical Service Bulletins across 17 categories
Categories
Engine
252 bulletinsThis service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customers vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This informational bulletin advises the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech did not properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides information for engine oil life monitor operation calculation.
This service bulletin provides information for engine oil life monitor operation calculation.
This bulletin updates the position of General Motors on refinishing aluminum wheels.
Read full bulletin
GM has determined that wheel refinishing under warranty will no longer be performed.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This PI bulletin advises the technician on the proper way to install the pistons in an engine.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin explains the difference in oil filters for gas engines with new oil pump control systems and the...
Read full bulletin
possibilities of what may happen using the incorrect filter.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This informational bulletin advised the technician that the engine and related parts will be debited if found that the...
Read full bulletin
tech didn't properly prepare the engine block from dirt and debris in bolt holes or if found that the block was damaged by the tech.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This service bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
driveability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This diagnostic tip bulletin provides additional information on how to diagnose a possible valve, lifter or camshaft...
Read full bulletin
issue.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This service bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This service bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle engine oil...
Read full bulletin
consumption.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the...
Read full bulletin
engine is started while diagnosing for noise from the engine or transmission.
This service bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines...
Read full bulletin
and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
This bulletin updates the position of General Motors on refinishing fully color painted aluminum wheels with base paint.
Read full bulletin
GM has established a new process for the way that refinishing under GM Warranty will be handled (U.S. ONLY).
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on the cold start control system in DI engines to reduce cold start emissions...
Read full bulletin
and improve fuel economy.
This Preliminary Information communication provides information to the technician about vehicles that have an unusual...
Read full bulletin
noise and is difficult to identify, isolate or pinpoint. Technician should get record a sound clip or take a video of the noise for assessment by engineering. Technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This service bulletin provides information on replacing the intake manifold when the engine is replaced after severe...
Read full bulletin
internal engine damage.
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Warranty Admin service bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact...
Read full bulletin
the PQC for engine or transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
Malfunction Indicator Lamp (MIL) Illuminated - DTC P0366 and/or P0014 Condition Some customers may comment that the MIL is illuminated.
Read full bulletin
The technician may find one or more of the following DTCs set: P0366 P0014 Cause This condition may be caused by a sporadically unlocked exhaust cam phaser that can oscillate during engine start, falsely setting the DTC/s. Correction If you encounter a vehicle with the above concern, reprogram the ECM software with the latest software available
This service bulletin provides graphics, information and guidelines for engine component wear to assist service...
Read full bulletin
personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns for Canadian Dealers only.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors and General Motors...
Read full bulletin
of Canada Company do not support cross border sales. The General Motors of Canada Customer Care Centre is the sole authorized provider of a certification confirmation letter which helps our customers identify if their vehicles meets the required USA regulatory standards necessary for importation into the USA.
This bulletin provides information on Policies Applicable to All U.S.
Read full bulletin
Dealers for Engine and Transmission Assembly Replacement Under Warranty, Policy or Customer Enthusiasm and information on Submission of Warranty Transaction in Global Warranty Management.
This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct...
Read full bulletin
conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Warranty Administration bulletin is for information on General Motors New Vehicle Tire Warranty Program (U.S.
Read full bulletin
Dealers Only).
This warranty administration bulletin provides information on the tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a...
Read full bulletin
guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This informational bulletin provides retail, wholesale and fleet personnel with General Motors recommendations for...
Read full bulletin
customer concerns related to wheel alignment.
This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to...
Read full bulletin
correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include ?Vibration? ?Business Associate Code? and the last 8 of the Vehicle Identification Number.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact PARTECHand/orthe Techline Customer Support Center for additional support.
This bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or...
Read full bulletin
GDS 2.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin provides information on replacing the intake manifold when the engine is replaced after...
Read full bulletin
severe internal engine damage.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians shouldrefer to Service Information for information regarding most accessories. Technicians mayalso contact Partechand/orthe Techline Customer Support Center for additional support.
This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with...
Read full bulletin
conductive finish.
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using...
Read full bulletin
the Tech 2 or GDS 2.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This bulletin provides information on Engine Concerns that could result from lack of scheduled maintenance, improper...
Read full bulletin
service or aftermarket calibrations.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician to not remove the torque converter...
Read full bulletin
bolts and start the engine as this may cause damage to the torque converter of the crankshaft on vehicles equipped with an automatic transmission.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted andnot start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This informational bulletin provides information on Internal Engine Noise or Damage After Oil Filter Replacement.
This informational bulletin provides information for the dealer technician to gather as much information to help aid...
Read full bulletin
Engineers by completely filling out requested reports.
This informational bulletin provides information on a normal engine operating condition for faster emission warm up...
Read full bulletin
time.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version. If the Firmware Over-the-Air version on the scan tool equals 6708 the technician will need to contact General Motors Technical Assistance Center for further assistance. If the Firmware Over-the-Air version on the scan tool is lower than 6708 Dealer can order the part thought the Instrument Sales and Service website process.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B terminal...
Read full bulletin
test probe, replacement terminals, and terminated leads. The J-35616-64B is the latest test probe released for checking tension or probing the .64 series terminals. The test probe terminal has been released in the terminal repair kit (J-38125-620H) located in Lear Tray 7 part number 963716-2. There are 5 terminated leads in a package part number is 13505346, which can be ordered through your normal General Motors Customer Care and Aftersales parts channel.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory parts/kits.
Read full bulletin
Technicians should refer to Service Information for information regarding most accessories. Technicians may also contact Partech and/or the Techline Customer Support Center for additional support.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Bulletin provides guidelines for Dealers Not Required and for Dealers Required to Contact the PQC for engine or...
Read full bulletin
transmission assembly replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Preliminary Information communication provides information to the technician about vehicles that have had multiple...
Read full bulletin
repair attempts that are being performed on customer?s vehicles that exhibit vibration conditions without utilizing the support of General Motors Technical Assistance Center. If valid vibration frequency or Road Force Variation data has been collected and a repair attempt does not correct the customer complaint, contact General Motors Technical Assistance Center for further support. For any vehicles that remains unrepaired after being at the dealer for three days or more and a related bulletin or PI is not found, contact General Motors Technical Assistance Center for further support.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This Preliminary information communicates information that will need to be provided to TAC to aid in diagnosing if a...
Read full bulletin
vehicle comes in with misfire and DTC Codes P0300 - P0308 and/or P050D
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air.
Read full bulletin
Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module...
Read full bulletin
when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.
This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward.
Read full bulletin
This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
This informational bulletin provides information on OnStar VCIM is currently restricted parts.
Read full bulletin
By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
This informational bulletin provides information on Intake Manifold Inspection/Replacement After Severe Internal Engine...
Read full bulletin
Damage.
This preliminary informational bulletin provides information on Damaged, Disassembled or Improperly Packaged...
Read full bulletin
Turbochargers Returned to Warranty Part Center.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This technical bulletin provides a procedure to replace the engine cover and perform an ECM update if the engine cover...
Read full bulletin
is found discolored.
This technical bulletin provides repair information for repairing the IP to body harness connector to correct a customer...
Read full bulletin
concern for intermittent Malfunction Indicator Lamp (MIL) illuminated with Reduced Engine Power displayed and DTC P2138 set.
This informational bulletin provides information to dealership personnel on automatic transmission shift and engine...
Read full bulletin
drivability concerns and/or MIL ON due to aftermarket oil bath air filter use.
This informational bulletin provides guidelines and diagnostic/repair information to technicians regarding vehicle...
Read full bulletin
engine oil consumption.
This Preliminary Information communication provides information to the technician about engine block of possible...
Read full bulletin
cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about customers that may complain of...
Read full bulletin
various concerns when using Bluetooth components. Technician should use the Preliminary Information to gather information from the customer on their Bluetooth device and the concern they are having before calling General Motors Technical Assistance Center.
This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains...
Read full bulletin
how toptier fuels should be used to reduce carbon build up.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This informational bulletin provides information on General Motors Dealership Critical Equipment Requirements and...
Read full bulletin
Recommendations.
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk...
Read full bulletin
on engine surfaces.
This informational bulletin provides information for engine oil life monitor operation calculation.
This informational bulletin provides information on OEM and Remanufactured Engine and Automatic Transmission/Transaxle...
Read full bulletin
Identification.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (in Canada, the Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This informational bulletin provides information on identifying Non-GM Engine Calibrations for Gasoline Engines using the Tech 2 or GDS 2 9U.S.
Read full bulletin
and Canada
This Bulletin provides graphics, information and guidelines for engine component wear that require repair and not engine...
Read full bulletin
replacement.
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly...
Read full bulletin
replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This Bulletin provides guidelines for Dealers to determine whether or not they need to contact the PQC for an engine,...
Read full bulletin
transmission or transfer case assembly replacement and information explaining the PQC process, Global Warranty Management Transaction submission, vehicle repair record retention and proper handling of assembly returns.
This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles.
Read full bulletin
General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
This informational bulletin provides information on intake manifold inspection/replacement after severe internal engine...
Read full bulletin
damage.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will use Global Diagnostic System 2 to review the Firmware Over-the-Air version and the OnStar Customer Identifier and contact General Motors Technical Assistance Center for further assistance.
This preliminary informational bulletin was created to inform Service Agents or Dealers, they may be charged back for...
Read full bulletin
parts and labor due to the turbo-chargers are being returned to the Warranty Parts center damaged, improperly assembled or missing parts and advising to properly package the complete turbochargers. (New models and RPOs added)
This informational Bulletin provides Do's and Don'ts for maximizing gasoline engine fuel economy, other various tips and...
Read full bulletin
a list of websites for additional information.
This GM of Canada New Vehicle Tire Warranty Program and GWM Transaction Submission Information Bulletin provides...
Read full bulletin
information for the new tires that the vehicle are equipped with and that they are covered by General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage) and for vehicles within this warranty period, the defective tires will be replaced on a pro rata adjustment basis. It also provides GWM Transaction information.
This warranty administration bulletin provides information on The tires supplied with a new vehicle are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the Bumper-to-Bumper New Vehicle Limited Warranty.
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B...
Read full bulletin
may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
This Preliminary Information communication provides information to the technician about vehicles that the radio will not...
Read full bulletin
retain the previous settings and will go to the Home Icon screen when the vehicle is restarted. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is currently evaluating this concern.
This Preliminary Information communication provides information to the technician about vehicles that when watching a...
Read full bulletin
movie the audio does not match the video when playing though the vehicles speakers. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats.
Read full bulletin
Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
This Bulletin provides guidelines for Dealers required to contact the PQC for engine or transmission assembly...
Read full bulletin
replacement and explains the PQC process, GWM Transaction submission, vehicle service record retention and proper handling of assembly returns.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This informational bulletin provides information on OnStar VCIM is currently restricted parts.
Read full bulletin
By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats.
Read full bulletin
Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
This Preliminary Information communication provides information to the technician about engine block that have a...
Read full bulletin
possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to contact General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This informational bulletin provides information on identifying non-GM (aftermarket) engine calibrations for gasoline...
Read full bulletin
engines using Tech 2 or GDS 2.
This informational bulletin updates General Motor's position on refinishing aluminum wheels.
Read full bulletin
GM does not endorse any repairs that involve welding, bending, straightening or re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed.
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B...
Read full bulletin
may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
This Preliminary information communicatesIn ambient temperatures 100F (37.7 C)degrees or higher, DTCs P2635 and/or P018B...
Read full bulletin
may set.The vehicle may also exhibit a hesitation or stalling condition.Excessively Hot and sustained ambient temperatures over 100F (37.7 C) degrees Mainly in TX, AZ, UT, NV, CA, NM (could be any state) causingVapor buildup in fuel feed line.Customers can be advised to utilize fuels with octane levels greater than 91, Refrain from extended idleing periods if possible, park vehicles in covered garage.Replacing the fuel pump will not repare this concern.
This preliminary informational bulletin provides a diagnostic tip for technicians who may find an oil leak after a...
Read full bulletin
recent oil change has been performed.
This Preliminary Information communication provides information to the technician about vehicle that may have an OnStar...
Read full bulletin
system that has progression tones when pressing the blue or red button. Technician will need to call General Motors Technical Assistance Center with the scan tool data from the OnStar system.
This Preliminary Information communication provides information to the technician about vehicles with the service engine soon lamp that comes on.
Read full bulletin
Technician may find Diagnostic Trouble Code U0101. Technician should review the appropriate Service Information diagnostics for DTC U0101. Also gather all other diagnostic trouble codes in the vehicle and which modules they are set in. The transmission connector pins should be checked for damaged terminals or poor terminal fit. Also inspect the under hood fuse block for damaged terminals or poor terminal fit and mis-positioned fuses in fuse block. Inspect the ground for the Transmission Control Module. Technician should refer to Service Information automatic transmission controls schematics to determine the ground identification.
This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles...
Read full bulletin
that may have an OnStar Turn-By-Turn Navigation the system that is inoperative. Technician verifies there are no Diagnostic Trouble Codes are present in the Antilock Braking System and Vehicle Communication Interface Module of the vehicle. If no Diagnostic Trouble Codes found call OnStar using the Blue button on the OnStar key pad and ask the advisor for a turn by turn route. Also make a OnStar personal call and a call into the vehicle. If normal diagnostics do not lead to a resolution technician will need to call General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction...
Read full bulletin
Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years.
This Preliminary Information communication provides information to the technician about vibration complaints that are...
Read full bulletin
one of the most challenging complaints to accurately diagnose and repair. Technician will need to use Pico Oscilloscope Diagnostic Kit to effectively diagnosis vehicles. Technician should drive the vehicle will using the Pico Oscilloscope to record data. After the data is recorded it should be reviewed to determine the root cause of the concern. If a repair attempt made the concern better but not eliminated or had no affect at all, and are requesting assistance from General Motors Technical Assistance Center record another Pico file and save it to the computer. After the new Pico Oscilloscope data has been saved email the data to General Motors Technical Assistance Center in the subject line include “Vibration” “Business Associate Code” and the last 8 of the Vehicle Identification Number.
This Preliminary Information communication provides information to the technician that General Motors Technical...
Read full bulletin
Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D stored in Telematics Communication Interface Control Module. Technician will need to ensure campaigns 14395 or 15086 are completed. Technician will need to use Global Diagnostic System 2 and gather information and contact General Motors Technical Assistance Center for further assistance.
This Preliminary Information communication advises the technician that the Human Machine Interface, Radio or Tuner,...
Read full bulletin
radio controls, Integrated Center Stack, display, and Media Disc Players are placed on restriction through the General Motors Technical Assistance Center. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
This bulletin contains information for the new tires that the vehicle is equipped with and that they are covered by...
Read full bulletin
General Motors against defects in material or workmanship under the New Vehicle Warranty (Base Warranty Coverage). For vehicles within this warranty period, defective tires will be replaced on a pro rata adjustment basis according to the published distance-based schedule.
This Preliminary Information communication provides information to the technician about vehicles that have a Diagnostic...
Read full bulletin
Trouble Code B101D-37 history in the Vehicle Communication Interface Module or telematics communication interface control module. Engineering has determined that this code will only display in history on the scan tool and will not cause issues with OnStar system operation.
This Preliminary Information communication provides information to the technician about vehicles that when an incoming...
Read full bulletin
Bluetooth call will ring through the vehicle system, but the call can only be answered by using the handset. Technician can update the radio using the latest version of 15-NA-081 if the vehicle is 2014 or newer. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
THIS INFORMATIONAL BULLETIN PROVIDES THE TECHNICIAN WITH WHAT MAY HAPPEN TO AN ENGINE DUE TO LACK OF MAINTENANCE.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE THE...
Read full bulletin
ONSTAR WIRELESS FIDELITY INOPERATIVE. TECHNICIAN WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER WITH A SCAN TOOL CONNECT TO THE VEHICLE FOR FURTHER ASSISTANCE.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ABOUT THE CALCULATION AND OPERATION OF THE ENGINE OIL LIFE MONITOR.
Read full bulletin
THE MONITOR CALCULATES THE PERCENT OF OIL LIFE REMAINING, BASED ON 3 PATHWAYS. THE FIRST PATHWAY FOR OIL LIFE CALCULATION IS ENGINE REVOLUTIONS. THE SECOND PATHWAY FOR OIL LIFE CALCULATION IS THE MILEAGE FORM THE LAST REST FOR ALL GENERAL MOTORS POWERTRAINS EXCEPT THE VOLT. THE THIRD PATHWAY FOR OIL LIFE CALCULATION IS THE AMOUNT OF TIME THE OIL IS IN THE ENGINE. THE VOLT USES A 2 YEAR TIMER INSTEAD OF 1 YEAR. IT ALSO USES THE ENGINE REVOLUTION COUNTER. IT DOES NOT USE THE MILEAGE PATHWAY TO COUNT DOWN.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT AFTER REPLACING THE INSTRUMENT...
Read full bulletin
PANEL CLUSTER THE EXCHANGE CENTER IS UNABLE TO PROGRAM THE ACTUAL MILEAGE ON THE ODOMETER OR THE ACTUAL MILEAGE IS UNKNOWN. DEALER WILL NEED TO FOLLOW DEALER TO THE GENERAL MOTORS SERVICE POLICIES AND PROCEDURES MANUAL SECTION 5.2.4 ODOMETER SERVICING.
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDES INFORMATION ON THE TIRES SUPPLIED WITH A NEW VEHICLE ARE COVERED BY...
Read full bulletin
GENERAL MOTORS AGAINST DEFECTS IN MATERIAL OR WORKMANSHIP UNDER THE BUMPER-TO-BUMPER NEW VEHICLE LIMITED WARRANTY.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THAT THE HUMAN MACHINE INTERFACE, RADIO OR TUNER,...
Read full bulletin
RADIO CONTROLS, INTEGRATED CENTER STACK, DISPLAY, AND MEDIA DISC PLAYERS ARE PLACED ON RESTRICTION THROUGH THE GENERAL MOTORS TECHNICAL ASSISTANCE CENTER. DEALER WILL NEED TO CONTACT GENERAL MOTORS TECHNICAL ASSISTANCE CENTER FOR FURTHER ASSISTANCE.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE USE OF J-35616-64B TERMINAL...
Read full bulletin
TEST PROBE, REPLACEMENT TERMINALS, AND TERMINATED LEADS. THE J-35616-64B IS THE LATEST TEST PROBE RELEASED FOR CHECKING TENSION OR PROBING THE .64 SERIES TERMINALS. THE TEST PROBE TERMINAL HAS BEEN RELEASED IN THE TERMINAL REPAIR KIT (J-38125-620H) LOCATED IN LEAR TRAY 7 PART NUMBER 963716-2. THERE ARE 5 TERMINATED LEADS IN A PACKAGE PART NUMBER IS 13505346, WHICH CAN BE ORDERED THROUGH YOUR NORMAL GENERAL MOTORS CUSTOMER CARE AND AFTERSALES PARTS CHANNEL
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES THE TECHNICIAN WITH STEPS ON HOW TO PROGRAM AN ENGINE CONTROL MODULE...
Read full bulletin
WHEN GETTING A SERVICE PROGRAMMING SYSTEM ERROR CODE E4491 OR E4423. IN SOME CASES TECHLINE CUSTOMER SUPPORT CENTER MAY NEED TO BE CONTACTED TO RESOLVE THE ISSUE.
THIS INFORMATIONAL BULLETIN PROVIDES ADDITIONAL INFORMATION ON HOW TO INSTALL PISTONS AND SUGGEST WHAT TOOLS TO USE.
THIS INFORMATIONAL BULLETIN EXPLAINS THE USE OF DIESEL FUEL ADDITIVES IN AN ENGINE, ARE NOT REQUIRED UNLESS THE CUSTOMER...
Read full bulletin
DESIRES ADDITIVES TO PREVENT FUEL CONCERNS DEPENDING ON FUEL OR TEMPERATURE RELATED CONDITIONS.
THIS INFORMATIONAL BULLETINS PROVIDES INFORMATION ON THE INTAKE MANIFOLD INSPECTION/REPLACEMENT AFTER SERVERE INTERNAL...
Read full bulletin
ENGINE DAMAGE.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION TO GM DEALERS ON THE CORRECT CLEANING METHODS WHEN CLEANING ENGINE...
Read full bulletin
GASKET SEALING SURFACES.
Pre-Delivery & Maintenance
193 bulletinsThis service bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles that may...
Read full bulletin
not pass California smog inspection or smog inspection in other states.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on proper use of floor mats.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
The bulletin provides direction on how to locate the Temporary Service Part (TSP) form in GlobalConnect.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes...
Read full bulletin
E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This warranty administration bulletin provides policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the vehicles...
Read full bulletin
before being sold (prepping) to the customer.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on proper use of floor mats.
This service bulletin provides information for dealers/technicians on Over The Air (OTA) and In Market Enhancement (IME)...
Read full bulletin
FAQs.
This service bulletin provides technicians with information to help identify the differences between what is considered...
Read full bulletin
a fluid leak, and what is considered fluid seepage.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This service bulletin provides information on All hazmat parts being returned to the Warranty Parts Center (WPC) must be...
Read full bulletin
shipped using Central Transport. Hazardous materials should never be sent by air transportation to the WPC.
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure when diagnosing vibration concerns.
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
and Canada Dealers Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This service bulletin provides repair information to correct a customer concern of OnStar Inoperative after Importing...
Read full bulletin
Vehicle from Canada to the United States.
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on the proper use of the labor operation 0600014.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides information for dealers/technicians on Over the Air (OTA) and In Market Enhancement (IME)...
Read full bulletin
FAQs.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin describes the U.S.
Read full bulletin
Dealer Special Tool Loan Program process.
This service bulletin provides information on submitting quality Photos of Various Vehicle Concerns to the GM Technical...
Read full bulletin
Assistance Center (TAC).
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This service bulletin provides information on proper use of floor mats.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This warranty administration bulletin provides policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This Warranty Administration bulletin provides retail and wholesale service personnel with the policies/procedures and...
Read full bulletin
the warranty transaction submission procedures that support the Personal Property Damage process.
This Warranty Administration bulletin provides information on the Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This preliminary information (PI) provides information om Service Programming System (SPS) Error Codes (E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S.
Read full bulletin
and Canada.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
The intent of this service bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This service bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration service bulletin provides information for dealers/Service advisors on when and how to...
Read full bulletin
submit a Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty admin bulletin covers information on Essential Tools that include Consumable Parts.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This service bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before being sold (prepping) to the customer.
This service bulletin provides information for the Global Warranty Management (GWM) Warranty Parts Center (WPC) Part Photo Return Process (U.S.
Read full bulletin
Dealers Only).
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides policy information on warranty administration guidelines for multiple repairs with...
Read full bulletin
independent causes (GM Canada Dealers Only).
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides information for replacement parts traceability (RPT) process to aid in tracking part...
Read full bulletin
replacements.
This service bulletin provides service information on new torque specification and installation procedure for ACDelco...
Read full bulletin
Spin-On Oil Filters.
This service bulletin provides a vibration analysis worksheet the technician can use in conjunction with the appropriate...
Read full bulletin
Vibration Analysis-Road testing procedure, when diagnosing vibration concerns.
This service bulletin provides information for dealers/technicians and customers on steam/vapor coming from the front...
Read full bulletin
grille or radiator area.
This service bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered normal...
Read full bulletin
operation.
This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information for GM courtesy transportation and roadside assistance...
Read full bulletin
programs.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information on Enhancing Field Product Reports with Digital Pictures.
This service bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This warranty administration bulletin provides policy information requirements applicable to key fob replacement under...
Read full bulletin
the New Vehicle Limited Warranty or under a Replacement Parts Warranty on 2017-2022 and newer model year vehicles with RPO ATH and AVJ (U.S. Only).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This service bulletin provides information for dealers/technicians on accessory all-weather floor liners and flat mats...
Read full bulletin
warped or misshapen.
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA).
This warranty administration bulletin provide policy information for variable diagnostic time allowances on select labor operations (U.S.
Read full bulletin
Only).
This warranty administration bulletin provides information on Warranty Administration - Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This service bulletin provides information on Improved Oil Filter Gasket Design for Spin-On Oil Filters PF63, PF64 and...
Read full bulletin
PF48.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Warranty Administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This Warranty Administration bulletin provides information on Dealer Empowerment for Goodwill, Customer Enthusiasm and Policy (U.S.
Read full bulletin
Only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This warranty administration bulletin provides information on Global Warranty Management (GWM) Warranty Parts Center...
Read full bulletin
(WPC) Parts Return Program Information.
This warranty administration bulletin provides policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides information on Warranty Administration ? Customer Concern Not Duplicated...
Read full bulletin
(CCND) Labor Operation Numbers.
This Warranty Administration bulletin provides information on Essential Tools that include Consumable Parts (U.S.
Read full bulletin
Only).
This bulletin provides information on Warranty Administration ? Required Operating Procedures - 8 Points (U.S.
Read full bulletin
Only).
This warranty administration bulletin provide policy information to cover GMs policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This Warranty Administration bulletin provides information on customer vehicles concern results in a manufacturer...
Read full bulletin
repurchase from the customer, GM depends on the dealership to host and administer the repurchase closing and intake of the returning vehicle.
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This informational bulletin provides information to dealership personnel for new vehicles with less than 1,000 miles...
Read full bulletin
that may not pass California smog inspection or smog inspection in other states.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes (E4398,...
Read full bulletin
E4399, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491 or E6961).
This Warranty Administration bulletin provides information for dealers/Service advisors on when and how to submit a...
Read full bulletin
Pre-Repair Authorization (PRA) (US dealers only).
This Preliminary information communicates the use of air leak diagnostic test tool CH-52250 in addition to the...
Read full bulletin
information found in the service manual.
This preliminary information bulletin provides information om Service Programming System (SPS) Error Codes E4398, E4399,...
Read full bulletin
E4403, M4404, M4413, E4414, E4423, E4491 or E6961).
This warranty administration bulletin provides policy information, proper labor operation selection and causal part...
Read full bulletin
identification for warranty transactions (U.S. Only).
This warranty administration bulletin provide policy information to cover GM's policy on performing GM covered vehicle...
Read full bulletin
services and maintenance on vehicles originating/sold in Canada.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer...
Read full bulletin
Enthusiasm.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty nonadministrative bulletin provides information on the proper use of the labor operation 0600014.
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty bulletin provides labor operation numbers for customer concerns Not duplicated (CCND).
This warranty administration bulletin provides policy information on required operating procedures.
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S.
Read full bulletin
and Canada dealers only.
This warranty administration bulletin provide policy information on required operating procedures.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty bulletin explains how to determine if an outside mirrior was damaged by the customer and what is...
Read full bulletin
considered warranty and non-warranty.
This warranty bulletin provides labor operation numbers for customer concerns that cant be duplicated.
This informational bulletin provides information retaining to the fact that Service Manuals will now be available on...
Read full bulletin
USB.
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provide policy information on required operating procedures.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provide policy information on the change in product field action customer...
Read full bulletin
reimbursement procedure.
This warranty administration bulletin provide policy information on required operating procedures.
This bulletin provides information on approved warranty part numbers for original equipment batteries.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer...
Read full bulletin
Enthusiasm.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This informational bulletin advises the dealers to maintain the vehicle stock on hand by doing a full inspection on the...
Read full bulletin
vehicles before sold (prepping) to the customer.
This warranty administration bulletin provide policy information on required operating procedures.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provides dealership personnel with policy and procedure requirements for essential...
Read full bulletin
tools that include consumable parts (U.S. Only).
This warranty administration bulletin provides information on GM?s policy on performing GM covered vehicle services and...
Read full bulletin
maintenance on vehicles originating/sold in Canada.
This warranty administration bulletin provide policy information on required operating procedures.
This warranty administration bulletin provides information on Goodwill Tools, Customer Enthusiasm, and Policy...
Read full bulletin
Guidelines.
This warranty nonadministrative bulletin provides information on the proper use of the labor op 0600014.
This Warranty Admin bulletin provides retail and wholesale service personnel with the policies/procedures and the...
Read full bulletin
warranty transaction submission procedures that support the Personal Property Damage process.
This warranty administration bulletin provide policy information on warranty and policy exchange program for electronic products for U.S.
Read full bulletin
and Canada dealers only.
This warranty administration bulletin provide policy information for courtesy transportation and roadside assistance...
Read full bulletin
programs.
This warranty administration bulletin provides policy information on Causal Part requirements for transactions submitted...
Read full bulletin
to GM for payment.
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This informational bulletin provides information on approved warranty part numbers for original equipment batteries
This warranty administration bulletin provides information on Dealer Empowerment Labor Operations and Customer...
Read full bulletin
Enthusiasm.
This warranty administration bulletin provides information on Courtesy Transportation and Roadside Assistance Programs
This informational bulletin provides information on New Vehicle Pre-Delivery Inspection (PDI) - Delivering Quality...
Read full bulletin
Vehicles and Generating Higher CSi Scores
This warranty informational bulletin provides a list of all the required operating procedures and explains them out to...
Read full bulletin
what is acceptable and not.
This warranty administration bulletin provide policy information for GM dealer empowerment program and goodwill...
Read full bulletin
procedures.
This informational bulletin provides warranty policy information on required operating procedures.
THIS WARRANTY ADMINISTRATION BULLETIN PROVIDE POLICY ON PERFORMING GM COVERED VEHICLE SERVICES AND MAINTENANCE ON...
Read full bulletin
VEHICLES ORIGINATING/SOLD IN CANADA.
Other
118 bulletinsThis preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
New Vehicle Monitoring Programs Section in IVH
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This preliminary information advises a dealer on how to email GDS2 session logs into Technical Assistance.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This Preliminary Information communication provides information to the technician about the use of J-35616-64B and Mini...
Read full bulletin
50 terminal test probe, replacement terminals, and terminated leads.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This bulletin advises the technician to flush the cooling system multiple times if oil has been found in the cooling...
Read full bulletin
system and replace the parts that may be contaminated due to oil in system.
This Preliminary information communicates to the dealer a process for accessing the procedure to add attachments to a GM...
Read full bulletin
technical assistance case using the dealer case management tool.
This Preliminary information communicates to dealers GM is working on a solution for outdated Apps
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary Information communicates helpful information on diagnosing generalcustomer concerns related to a power...
Read full bulletin
folding top.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Preliminary Information communicates helpful information on diagnosing generalcustomer concerns related to a power...
Read full bulletin
folding top.
This informational bulletin provides information on a guide to help reduce repeat visits for the same customer concern.
This Preliminary information communicates a process to correct theconcern of Unable to contact OnStar after the 3G EOL...
Read full bulletin
on 2015-2022 model year vehicles in the United States.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This informational bulletin provides information on proper use of floor mats.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
Essential Tools that Include Consumable Parts (U.S.
Read full bulletin
Only)
Information Regarding the Differences Between Fluid Leakage and Seepage This bulletin is intended to help identify...
Read full bulletin
the differences between what is considered a fluid leak and what is considered seepage. Improper diagnosis may lead to unnecessary component replacement. Use the following information to determine if the condition is normal acceptable seepage or a defective component
IPC Odometer Programming Method Quick Reference Guide
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This Preliminary Information communicates helpful information on diagnosing generalcustomer concerns related to a power...
Read full bulletin
folding top.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This bulletin provides information to dealers regarding transportation damage repair claim submission requirements.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides information for dealers/technicians on When and How to Submit a Field Product Report (FPR) (U.S.
Read full bulletin
Dealers Only).
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This Preliminary Information communicates helpful information on diagnosing generalcustomer concerns related to a power...
Read full bulletin
folding top.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin provides information for dealers how to submit a product information report (PIR) (Canada...
Read full bulletin
Only).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin provides process information for the (GWM) and (WPC) parts return program.
This Preliminary information communicates additional information on how a LIN bus operates and diagnostic tips when...
Read full bulletin
working on a LIN bus.
This Preliminary information communicatesdirection and examples when diagnosing multiple DTCs, one of which includes...
Read full bulletin
U**** Byte 71 DTC.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This informational bulletin provides information for dealers/technicians and customers on steam/vapor coming from the...
Read full bulletin
front grille or radiator area.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin explains the importance of maintaining the vehicle.
This informational bulletin provides information on proper use of floor mats.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information on interior cleaning products and what is offered to clean the...
Read full bulletin
interiors of GM vehicles.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known as a Product...
Read full bulletin
Allegation Resolution (PAR) claim.
This informational bulletin provides the dealer with information on what to do when requesting a new key code for the...
Read full bulletin
customer.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information for dealers/technicians on Use of Dealer Case Management (DCM) and Being Prepared for Contacting U.S.
Read full bulletin
Technical Assistance (TAC).
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles.
Read full bulletin
A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
This Preliminary information communicates
This Preliminary Information communication provides information to the technician about connectivity concerns when...
Read full bulletin
connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
The intent of this technical bulletin is to identify aftermarket ALDL or DLC interface devices as potential sources for...
Read full bulletin
causing multiple customer concerns that do not have other diagnostic methods to identify them.
This Bulletin provides a procedure to activate/enable 4G LTE Wi-Fi Hotspot on New vehicle.
This informational bulletin provides information to dealership personnel on enhancing field product reports with digital...
Read full bulletin
pictures.
This informational bulletin provides information on dealer responsibility for cargo carrying capacity labeling and the...
Read full bulletin
part numbers for the labels.
This informational bulletin provides a listing of the parts availability for coax repair procedures and what is needed...
Read full bulletin
to complete some repairs.
This bulletin describes the Dealer special tool loan program process.
This informational bulletin provides information on Driveline Clunk Noise and what is acceptable and what is considered...
Read full bulletin
normal operations.
This informational bulletin explains the Road Force balancers and what they can do for customer concerns.
This informational bulletin explains the difference in oil filters and the possibilities of what may happen using the...
Read full bulletin
incorrect filter.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information to dealership personnel on policies regarding a Product Assistance...
Read full bulletin
Claim (PAC) within the Courtesy Transportation Assistance Program.
This informational bulletin provides information for use on a Product Assistance Claim (PAC), which is formally known...
Read full bulletin
as a Product Allegation Resolution (PAR) claim.
This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in...
Read full bulletin
higher CSi scores.
This informational bulletin provides information to dealership personnel on properly eliminating unwanted odors in...
Read full bulletin
vehicles.
This informational bulletin provides a revision for 09-06-04-015B (Vehicles Sitting Outside on Dealer Lots for Extended...
Read full bulletin
Periods with Hard Start/No Start Condition) to add the 2015-2018 model years.
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications...
Read full bulletin
to Control GM Accessory Remote Start Kits.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This informational bulletin provides information to the customer about the rear camera guidelines not being present at...
Read full bulletin
times due to the VBM taking over the rear camera option.
This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change.
Read full bulletin
Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
This Preliminary information communicates to the technician the need to inspect the induction system for potential icing...
Read full bulletin
issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
This Preliminary Information communication advises the technician how to determine if the vehicle is equipped with wireless fidelity.
Read full bulletin
Technician should check the Regular Production Option Code list for (VV4).
This informational bulletin provides information on Information on How to Prevent Inadvertent Vehicle Starting from Key...
Read full bulletin
Fob or OnStar Mobile Application and where to locate the information for future use.
This informational bulletin explains the Road Force balancers and what they can do for customer concerns.
This Preliminary Information communication provides information to the technician about what XM offerings are available for vehicles.
Read full bulletin
A dealer or customer can access the website listed below for vehicle specific XM offerings and availability.
This informational bulletin explains the programming method quick reference guide for the IPC Odometer.
This informational bulletin provides information on comebacks prevention information and using customer concern...
Read full bulletin
verification sheets (CCVS).
This informational bulletin provides information on a new U.S.
Read full bulletin
dealer special tool loan program.
This informational bulletin provides Information Regarding Servicing Components Located Near SIR Components and how to...
Read full bulletin
properly disable the SIR system for repairs at or near
This informational bulletin provides information for dealers how to submit a product information report.
This informational bulletin provides information for dealers/technicians on when and how to submit a field product...
Read full bulletin
report.
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications...
Read full bulletin
to Control GM Accessory Remote Start Kits.
This informational bulletin provides information for the IPC odometer programming method quick reference guide.
This Preliminary Information communication advises the technician how determine if the vehicle is equipped with wireless fidelity.
Read full bulletin
Technician should check the Regular Production Option Code list for (VV4).
this informational bulletin provides Information on Using MyBuick, MyCadillac, MyChevrolet, and MyGMC Phone Applications...
Read full bulletin
to Control GM Accessory Remote Start Kits.
This informational bulletin provides information on proper use of floor mats.
This preliminary informational bulletin provides information on GM Accessory Remote start not working with onstars...
Read full bulletin
remotelink phone applications
This informational bulletin provides information on what is needed to be prepared for TAC, caller preparedness and checklists and contacting U.S.
Read full bulletin
technical Assistance and the use of strategy based diagnostics
This informational bulletin provides information on how to properly maintain vehicles in the dealer inventory
This informational bulletin provides information for the (GWM) and (WPC) on parts return program.
This informational bulletin provides information for dealers/technicians on when and how to submit a field product...
Read full bulletin
report.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PROPER USE OF FLOOR MATS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN TO DIAGNOSE THE CONCERN AND THE STEPS TO REPAIR THE CONCERN.
Read full bulletin
THE VEHICLE'S XM TRAVEL LINK MAY BE INOPERTIVE.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON GM DOES NOT APPROVE THE USE OF CLIPPING TO REPAIR COLLISION DAMAGE TO VEHICLES.
Read full bulletin
GM HAS NOT TESTED OR VALIDATED A CLIPPED VEHICLE REPAIR; THEREFORE, GM CANNOT ENDORSE THIS TYPE OF REPAIR OR CONFIRM THE CRASH PERFORMANCE DURING A SUBSEQUENT COLLISION.
THIS INFORMATIONAL BULLETIN EXPLAINS A POSSIBLE NORMAL WHINING NOISE FROM THE BALANCE SHAFT CHAIN IF THE VEHICLE HAS...
Read full bulletin
LESS THAN 10,000 MILES ON IT.
THIS TECHNICAL BULLETIN PROVIDES DIAGNOSTIC TIPS TO HELP CORRECT MULTIPLE CONCERNS REGARDING THE USB PORT BEING...
Read full bulletin
INOPERATIVE OR UNABLE TO PLAY MUSIC THROUGH THE USB PORT.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE IDENTIFICATION OF VEHICLES THAT ARE SHIPPED WITH THE TRANSPORT...
Read full bulletin
MODE ON AND HOW TO TURN IT OFF.
Electrical
82 bulletinsThis Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, B3935, C0750, C0755, C0760, C0765, and/or C0775.
This service bulletin provides information on the proper Reflective High Temperature Heat and/or Insulating Tape to use...
Read full bulletin
for certain repairs, such as Wiring Harness Repairs.
This Preliminary information communicates to the technician 3 ways to access the trunk when the electrical release latch...
Read full bulletin
is inoperative.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on key code security rules and information on GM keycode look-up applications...
Read full bulletin
(U.S).
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles.
Read full bulletin
It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for 12V battery testing and...
Read full bulletin
warranty replacements.
This Preliminary information communicates a GM part number forreflective high temperature heat or insulating tape when...
Read full bulletin
repairing wiring harnesses.
This service bulletin provides information on Module Harvesting.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers Correct...
Read full bulletin
battery cold cranking amperage (CCA) ratings and type are critical for proper test results when using the EL-50313. Access to the battery specification label, which contains the OEM part number and CCA rating and type, may be difficult without component removal. Refer to the table below for the original equipment ratings and part numbers used to set up a proper battery test. There has been some confusion as to the correct ACDelco battery warranty replacement. Refer to the table below for the correct battery warranty replacement. The correct ACDelco battery warranty replacement in the catalog is designated by the "Original Equipment Replacement" note in the description field.
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple...
Read full bulletin
keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
Information for Fleet Vehicles Ignition Key, Fob and Key Rings Configuration Some Customers are bundling multiple...
Read full bulletin
keys, fobs, and key tags together on a single crimped loop or a cable. This practice may result in unintended key rotation, and should be discontinued immediately. The information in this bulletin details the proper configurations for the ignition key, fob, key rings and key tags and applying a QR code sticker or barcode sticker to a key fob.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This warranty administration bulletin explains to the technician that when using wiring repair labor operations,...
Read full bulletin
additional information may be needed when submitting Global Warranty transactions when doing wiring repairs.
This informational bulletin provides information on key code security rules and information on GM keycode look-up...
Read full bulletin
applications.
This informational bulletin provides information on key code security and information on GM key code look up...
Read full bulletin
applications.
This bulleting provides Wiring, Terminal and Connector Repair Information including how to determine the Service Part...
Read full bulletin
Number in eSI and how to locate the part(s) in the EPC.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This bulletin provides information on the Transport Mode On Message Being Displayed in the Driver Information Center...
Read full bulletin
(DIC) and/or Battery Light is Flashing and the procedures to turn the Transport Mode message ON and OFF.
This bulletin provides information for electrical ground repairs using new replacement fasteners with "conductive...
Read full bulletin
finish".
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the Transport Mode message On and Off.
This bulletin explains the labor operation numbers used for submitting warranty claims for module reprogramming and not...
Read full bulletin
when replacing a module.
This warranty admin bulletin explains to the technician additional information may be needed when submitting...
Read full bulletin
transactions when doing wiring repairs.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to the technician about the Media Oriented Systems...
Read full bulletin
Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have driver and...
Read full bulletin
passenger temperatures settings are displayed in Celsius or the outside ambient temperature is missing from the radio / Heater-Vent-Air Conditioning display. Technician will need to use a scan tool to check for Diagnostic Trouble Codes in the Instrument Panel Cluster. If Diagnostic Trouble Code B0158 outside air temperature display malfunction is set check that the outside ambient temperature sensor is connected. If the sensor is connected, check the integrity of circuits 61 and 636 from sensor to the Instrument Panel Cluster or diagnose B0158 per published Service Information.
This Preliminary Information communication provides information to the technician on how to tell the difference between...
Read full bulletin
the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
This informational bulletin provides to the technician, locations to check for possible loose or damaged electrical...
Read full bulletin
connections that may set a DTC instead of just replacing a part.
This preliminary information bulletin provides a procedure on how to check for the customer concern of a blank radio...
Read full bulletin
with/without audio, by checking the the wiring harness, ECU and reprograming the HMI software update, if the wiring or ECU are not the cause.
This informational bulletin provides information on Wireless Charging Module Diagnosis and cell phone compatibility.
This informational bulletin provides information on On rare occasions, a security code input message with SPS error code...
Read full bulletin
E5659, M5304, and/or M5530 may be displayed in TIS2web when the technician is programming any module. If this concern is encountered, the technician should start by ensuring that the module being programmed is not a used module and that the VIN matches on VIN plate, TIS2web programming screen, and GDS2 module identification information screen.
This information bulletin explains the labor operation numbers used for submitting warranty claims and how to setup, and...
Read full bulletin
reprogram modules.
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
This informational bulletin explains to the dealer how to cover a possible customers mistake when a fuse has been blown.
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
This technical bulletin provides a procedure to properly reprogram an onstar module to correct a condition of Red LED,...
Read full bulletin
No WiFi Operation, and/or Limited OnStar Module Functionality After OnStar Module Replacement for Another Condition.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
Original Equipment Batteries Part Number and ACDelco Replacement Battery Approved Warranty Part Numbers
Battery Testing and Warranty Replacement Requirements (North America ONLY)
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This technical bulletin provides a procedure to perform an update to the ECM to correct a condition of MIL Illuminated.
The information in this bulletin details the proper configurations for the ignition key, fob, key tags, key rings, key...
Read full bulletin
ring sizes and applying a QR code sticker or barcode sticker to a key fob.
This informational bulletin provides warranty information on accessory power outlet and trailer lighting fuse...
Read full bulletin
replacement.
This Preliminary Information communication provides information to the technician about the Media Oriented Systems...
Read full bulletin
Transport Bus Diagnostic Tool Kit (EL-51578) has been released to help diagnose any of the Media Oriented Systems Transport bus concerns. The kit contains header connectors that are installed to bypass Media Oriented Systems Transport bus modules. The bypass connector also contains a terminal for verifying Media Oriented Systems Transport control circuit voltages. Technician should review Media Oriented Systems Transport bus description and operation and Diagnostic Trouble Code U0028 diagnostic procedures.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This Preliminary Information communication provides information to the technician about vehicles that have an OnStar system that will not power up.
Read full bulletin
Technician should turn off the ignition and cancel retained accessory power. After the vehicle has powered down remove power to the OnStar module for five minutes. After the power has been removed for five minutes, if the OnStar system is working release the vehicle. If the OnStar system is still inoperative continue with published Service Information diagnostics.
This informational bulletin provides to the tech the new version of SPS that will prompt warnings when trying to...
Read full bulletin
reprogram modules that have been already reprogrammed.
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
This Preliminary Information communication provides information to the technician about vehicles that have an...
Read full bulletin
intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency Identification Devices when the concern is present. Dealer should also direct their customers to the appropriate section in the Owner manuals that references that the device complies.
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required...
Read full bulletin
additional information.
This technical bulletin provides information on Transport Mode On Message Displayed in Driver Information Center (DIC)...
Read full bulletin
and/or Battery Light is Flashing and the procedures to turn the transport mode message on and off.
This informational bulletin provides information on Wireless Charging Module Diagnosis.
This warranty administration bulletin provides policy information on the requirements for battery testing and warranty...
Read full bulletin
replacements.
This Preliminary Information communication provides information to help the dealership technicians perform a parasitic...
Read full bulletin
drain test for the OnStar module. When performing battery parasitic drain test, there may be some confusion as to what the normal power consumption reading should be from the OnStar system.
This Preliminary Information communication provides information to the technician about vehicle that has no XM audio on...
Read full bulletin
certain channels but XM channel info is displayed. Technician will need to contact XM and deactivate and activate the module.
This informational bulletin provides information on Battery Testing and Warranty Replacement Requirements (North America...
Read full bulletin
ONLY)
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required...
Read full bulletin
additional information.
This informational bulletin provides warranty policy information on revised wiring repair labor operations and required...
Read full bulletin
additional information.
This informational bulletin provides information that the TPM sensors must always be relearned when accessory wheels are...
Read full bulletin
installed on the vehicle.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT THE MEDIA ORIENTED SYSTEMS...
Read full bulletin
TRANSPORT BUS DIAGNOSTIC TOOL KIT (EL-51578) HAS BEEN RELEASED TO HELP DIAGNOSE ANY OF THE MEDIA ORIENTED SYSTEMS TRANSPORT BUS CONCERNS. THE KIT CONTAINS HEADER CONNECTORS THAT ARE INSTALLED TO BYPASS MEDIA ORIENTED SYSTEMS TRANSPORT BUS MODULES. THE BYPASS CONNECTOR ALSO CONTAINS A TERMINAL FOR VERIFYING MEDIA ORIENTED SYSTEMS TRANSPORT CONTROL CIRCUIT VOLTAGES. TECHNICIAN SHOULD REVIEW MEDIA ORIENTED SYSTEMS TRANSPORT BUS DESCRIPTION AND OPERATION AND DIAGNOSTIC TROUBLE CODE U0028 DIAGNOSTIC PROCEDURES.
THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE AN ONSTAR SYSTEM THAT WILL NOT POWER UP.
Read full bulletin
TECHNICIAN SHOULD TURN OFF THE IGNITION AND CANCEL RETAINED ACCESSORY POWER. AFTER THE VEHICLE HAS POWERED DOWN REMOVE POWER TO THE ONSTAR MODULE FOR FIVE MINUTES. AFTER THE POWER HAS BEEN REMOVED FOR FIVE MINUTES, IF THE ONSTAR SYSTEM IS WORKING RELEASE THE VEHICLE. IF THE ONSTAR SYSTEM IS STILL INOPERATIVE CONTINUE WITH PUBLISHED SERVICE INFORMATION DIAGNOSTICS.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF...
Read full bulletin
RECEIVING FREQUENT "OFF ROUTE" MESSAGES WHILE FOLLOWING TURN BY TURN (TBT) ROUTE NAVIGATION. THE TECHNICIAN IS PROVIDED INSTRUCTIONS FOR RESETTING THE VEHICLE COMMUNICATION INTERFACE MODULE FOR THIS CONCERN.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON HOW TO TEST A BATTERY AND WHAT IS NEEDED TO WARRANTY A BATTERY.
THIS INFORMATIONAL BULLETIN PROVIDES THE CORRECT INFORMATION THAT IS NEEDED TO CORRECTLY KNOW WHAT TPM SENSOR IS NEEDED...
Read full bulletin
TO BE INSTALLED ON VEHICLES IF THERE IS ACCESSORY WHEELS INSTALLED AND WHO TO CONTACT WHEN THE ACCESSORY WHEELS WILL NOT LEARN THE TPM'S TO THE VEHICLES.
Body & Paint
54 bulletinsThis preliminary informational (PI) bulletin provides information to dealership personnel that may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This informational bulletin provides a procedure on how to remove the paint stain that may present itself under the...
Read full bulletin
shipping film.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This service bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This service bulletin provides repair information to correct a customer concern of the convertible top back glass...
Read full bulletin
separating from top cover material.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides information on Paintless Dent Repair Process.
This service bulletin provides information on Exterior Lamp Condensation and Water Leak Information and Replacement...
Read full bulletin
Guidelines.
This service bulletin provides repair information to correct a customer concern of the convertible top back glass...
Read full bulletin
separating from top cover material.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This preliminary informational (PI) bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and...
Read full bulletin
Replacement Guidelines.
This service bulletin provides information for dealers/technicians on glass ultraviolet (UV) Ray protection and tint...
Read full bulletin
percentage.
This service bulletin provides information regarding Witness Marks from Panel Adjustments Made During Manufacturing and...
Read full bulletin
that it is considered a normal condition.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This PI provides information on Rear and Side Tempered Glass Spots (Quench Marks) and that they are a normal...
Read full bulletin
characteristic.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This service bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of Chromed...
Read full bulletin
Aluminum Wheels.
This technical bulletin provides repair information to correct a customer concern of the convertible top back glass...
Read full bulletin
separating from top cover material.
This technical bulletin provides repair information to correct a customer concern of the convertible top back glass...
Read full bulletin
separating from top cover material.
This technical bulletin provides repair information to correct a customer concern of water sloshing in quarter panel...
Read full bulletin
area when accelerating or stopping and/or long period of water draining from rear wheel well after vehicle is parked.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin includes information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability.
This technical bulletin provides repair information to correct a customer concern of the convertible top back glass...
Read full bulletin
separating from top cover material.
This technical bulletin provides a procedure on how to clean and resurface aluminum wheel bead seats for vehicles that...
Read full bulletin
have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion.
This technical bulletin provides repair information to correct a customer concern of the convertible top back glass...
Read full bulletin
separating from top cover material.
This technical bulletin provides repair information for replacement of the folding top cover to correct a customer...
Read full bulletin
concern for pierced holes appearing in the sail panel area on one or both sides of the vehicle.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
This Preliminary Information communication advises the technician the steps on diagnosing the concern.
Read full bulletin
Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
Thins informational bulletin provides information on Paint-less Dent Repair Process.
This information bulletin provides a procedure on how to remove the paint stain that may present itself under the...
Read full bulletin
shipping film.
This Bulletin provides procedures to correct a condition of Power Foldaway Mirror Glass Shake, Flutter at Normal Driving...
Read full bulletin
Speeds
This technical bulletin provides repair information to correct a customer concern of water sloshing in quarter panel...
Read full bulletin
area when accelerating or stopping and/or long period of water draining from rear wheel well after vehicle is parked.
This Informational bulletin describes warranty part reviews where door glass had chips or scratches.
This informational bulletin provides information on Chemical Staining, Pitting, Corrosion and/or Spotted Appearance of...
Read full bulletin
Chromed Aluminum Wheels.
This PI bulletin provides information on Rear and Side Tempered Glass Spots (Quench Marks) and they are normal...
Read full bulletin
characteristic.
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This technical bulletin provides repair information for replacement of the folding top cover to correct a customer...
Read full bulletin
concern for pierced holes appearing in the sail panel area on one or both sides of the vehicle.
This informational bulletin provides information to help the customers that are not familiar with specialty tires like...
Read full bulletin
summer, competition, run-flat and self-sealing.
This informational bulletin provides information on new tools used for the Hem Flanges and how to repair and seal the...
Read full bulletin
flanges when the repairs are done.
This technical bulletin provides a procedure on how to clean and resurface wheel bead seats.
Read full bulletin
for vehicles that have the condition of Tire Slowly Goes Flat, Tire Air Loss, Low Tire Pressure Warning Light Illuminated, Aluminum Wheel Bead Seat Corrosion (Clean and Resurface Wheel Bead Seat)
This preliminary informational bulletin provides information to dealership personnel which may be helpful when...
Read full bulletin
addressing underbody component corrosion with customers.
This informational bulletin provides information on chemical staining, pitting, and corrosion on wheels and the proper...
Read full bulletin
cleaners to use to fix the conditions due to multiple causes.
This informational bulletin provides information on Interior Cleaning - Instrument Panel (IP), Hard or Plastic Surfaces,...
Read full bulletin
Seats, Carpet, Leather, Vinyl, Fabric Cleaner, Stain Remover, Restorer - Product Availability
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN THE STEPS ON DIAGNOSING THE CONCERN.
Read full bulletin
VEHICLE'S SUNROOF OPERATION INTERMITTENT, BIND, NOISE, AUTO-REVERSE, AND/OR WATER LEAKS.
Lighting
35 bulletinsThis warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or...
Read full bulletin
Replaced During Warranty Coverage Period.
This informational bulletin explains Unscheduled Supplemental Services and the importance of GM Simplified Maintenance...
Read full bulletin
Schedules.
This warranty administration service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or...
Read full bulletin
Replaced During Warranty Coverage Period.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This Preliminary information communicates to dealers of a known issue with failed map update
This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or...
Read full bulletin
Fog/Driving Lamp Damage.
This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed...
Read full bulletin
Accessories.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on some vehicles that may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This service bulletin provides information on Dealer Installed LPO Wheel Installation and Return Process.
This service bulletin provides information about GM Accessories - Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on GM Canada New Vehicle Tire Warranty Program for Original Equipment (OE)...
Read full bulletin
Tires and PDI installed Limited Production Option (LPO) Tires.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This service bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During Warranty...
Read full bulletin
Coverage Period.
This Preliminary Information communication provides information to the technician about vehicles with tire sidewall irregularities.
Read full bulletin
This is a visual condition that will not affect durability, reliability or performance of the tires. Dealer should communicate to the customer that slight sidewall indentations are a common characteristic of radial tire construction.
This informational bulletin explains Unscheduled Supplemental Services (including Flushing Services and Additives) and...
Read full bulletin
the Proper use of GM Simplified Maintenance Schedules.
This informational bulletin provides information on GM Accessories ? Dealer-Installed, Repaired or Replaced During...
Read full bulletin
Warranty Coverage Period.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement...
Read full bulletin
Guidelines.
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This informational bulletin was created to inform that any accessories that are installed from the GM factory will be...
Read full bulletin
covered under the standard vehicle warranty and dealer installed accessories will be covered for a full year (12 months).
This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in...
Read full bulletin
Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
This Preliminary Information communication provides information to the technician about vehicles that may have a clock...
Read full bulletin
that is slow to update while driving when the clock auto set feature enabled. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle.
This Preliminary Information communication provides information to the technician about vehicle's odometer appears...
Read full bulletin
to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system.
Read full bulletin
For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and...
Read full bulletin
what should be considered warranty replacement and not
This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system.
Read full bulletin
For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO ENABLE THE 4G LTE WIFI ON NEWLY DELIVERED VEHICLES FOR SOME VEHICLES...
Read full bulletin
THAT WERE NOT SHIPPED WITH THE FEATURE NOT ENABLED.
Fuel System
34 bulletinsThis warranty administration bulletin provides policy information on vehicles outside of a California Emissions State...
Read full bulletin
who move to and register their vehicle in a California Emission State may be entitled to the 7 year, 70,000-mile Emission Select State Component Limited Warranty.
This informational bulletin instructs the tech when fuel/fluid is needed to be tested and where it can be sent for...
Read full bulletin
analysis.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This service bulletin provides the technician with additional information on fuels, fuel additives and fuel management.
This service bulletin provides information for maintenance cleaning of the fuel injectors and gasoline detergent...
Read full bulletin
additive.
This Preliminary information communicates provides information to the technician on the use of R-99 or R-95 Renewable...
Read full bulletin
diesel fuel.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a...
Read full bulletin
customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This informational bulletin explains to the tech on how to order a new fuel injector by matching the part number on the...
Read full bulletin
part and ordering it from the EPC.
This Preliminary information communicates theuse of Winter grade fuel during the warm months of 2020 and the potential...
Read full bulletin
rivabilityissues that it can cause. The ongoing Coronavirus (COVID-19) pandemic has caused significant reductions in driving and fuel use. Due to the surplus of winter grade fuel sitting in storage (pipelines/stations) the EPA is waiving the fuel vapor requirement. This will extend the use of winter fuel into the summer months. The drivability concernsshould not be single events but should be multiple occurrences associated with hot days.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER Diesel Fuel...
Read full bulletin
Licensed Brands that are recommended for use in all GM vehicles and the TOP TIER FUELS website URL.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks...
Read full bulletin
using the evaporative emission cart smoke machine and ultrasonic leak detectortools.
This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure...
Read full bulletin
the line is reinstalled correctly to avoid a no/low fuel pressure situation.
This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if...
Read full bulletin
debris have entered the exhaust system.
This informational bulletin provides information on the TOP TIER Detergent Gasoline Licensed Brands and the TOP TIER...
Read full bulletin
Diesel Fuel Licensed Brands that are recommended for use in all GM vehicles.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This informational bulletin provides information on the top tier fuels that are recommended in GM vehicles.
This informational bulletin provides information for maintenance cleaning of the fuel injectors.
This Preliminary Information communicates to the dealer the process for downloading or updating operating software for...
Read full bulletin
the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update.
Transmission
31 bulletinsThe service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This service bulletin provides information on the harmful effects of ethylene glycol in transmission fluid.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin informs the technician of an alternate lift procedure that has been developed when the lift plate...
Read full bulletin
does not fit the top of the transmission case for 6T30, 6T35, 6T40, 6T45, and 6T50 Transmissions.
GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities.
Read full bulletin
The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when...
Read full bulletin
the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This service bulletin provides information for automatic transmission Oil Cooler Flush and flow test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This service bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering gear...
Read full bulletin
due to seeing grease or sealant on certain locations on the gear.
Information on Transmission Adaptive Functions and Correcting Low Mileage Harsh Shifts, Slips, or Flares.
This Preliminary information communicates to the dealer technician that TAC recommends the utilization of the GDS2...
Read full bulletin
software to aid in diagnosing automatic transmission concerns. TAC is requesting the GDS2 session logs be sent in before the dealer contacts TAC.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This informational bulletin provides normal operating characteristics and diagnostic information on Manual...
Read full bulletin
transmissions.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This warranty administration bulletin provide policy information for automatic transmission Oil Cooler Flush and flow...
Read full bulletin
test.
This bulletin provides information on the harmful effects of water or ethylene glycol in transmission fluid.
This technical bulletin provides a procedure inspecting for excess grease or Sealant on the Exterior of the steering...
Read full bulletin
gear due to seeing grease or sealant on certain locations on the gear.
This Preliminary Information communication provides information to the technician about the rear view camera options on...
Read full bulletin
the vehicles equipped with rear view camera. The rear view camera brightness can be adjusted on some models while the transmission is in reverse and using the Menu or Select button. To turn off or on the guidelines in the rear view camera, use the radio display Config icon then Display, then the guidelines option.
THIS TECHNICAL BULLETIN PROVIDES THE PROCEDURES TO COMPLETE A TRANSSMISSION ADAPTIVE LEARN ON ALL THE DIFFERENT TYPES OF...
Read full bulletin
VEHICLES AND TRANSMISSIONS BASED ON RPO OPTIONS TO CORRECT A CONDITION OF HARSH SHIFTS ON HARD ACCELLERATIONS.
Infotainment
25 bulletinsThis Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a...
Read full bulletin
vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
This technical bulletin provides repair information to correct a customer concern of no AM station available and/or...
Read full bulletin
receiving poor AM radio reception.
This Preliminary information communicates that when a customer or technician attempts to add a new transmitter to a...
Read full bulletin
vehicle following the adding transmitters without Service Programming System procedure the procedure will not complete and a message "Remote Learn Pending" will be displayed on the Driver Information Center. In the past to perform the new transmitter procedure only one previously learned transmitter was required but this is no longer the case. Now, two previously learned transmitters are required to be placed into the cup holder and then the new transmitter to be programmed placed in the transmitter pocket. If this new procedure is not followed, the "adding transmitters without Service Programming System" cannot be performed. The technician will be forced to add a transmitter using Service Programming System.
This Preliminary Information communication provides information to the technician with a diagnostic tip for navigation...
Read full bulletin
radios that have inaccurate entries at times when using the voice recognition to input the address. When using the Navigation command "Address" or "Destination" this Allows an address to be stated as a one-shot method. When using the Navigation command "Directed Address" this Allows an address to be stated one step at a time. Directed address option may be a better choice for entering that address.
This Preliminary Information communication provides information to the technician about vehicles that may have an issue...
Read full bulletin
when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
This informational bulletin provides information for the technicians on multi-media infotainment tester (MIT), does not...
Read full bulletin
function properly when diagnosing infotainment complaints, which may lead to mis-diagnosis.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a...
Read full bulletin
condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This technical bulletin provides repair information to correct a customer concern of receiving poor Am radio reception...
Read full bulletin
in comparison to FM or XM.
This informational bulletin provides information on Audio Volume Stuck High or Low with No DTCs and that this is a...
Read full bulletin
normal characteristic.
This technical bulletin provides a procedure to clear the codes and re-evaluate the XM radio channels to correct a...
Read full bulletin
condition of audio muting when listening to some Sirius XM channels but if they change channels they will find others that experience normal audio. This could be due to interference from transmitting sources outside of Sirius XM?s frequency range.
This informational bulletin provides information on correct positioning of the cargo shade partition and forward...
Read full bulletin
pass-through flap to eliminate the condition of convertible top inoperative and "Extend Cargo Shade to Operate Top" message displayed in DIC.
This Informational Bulletin provides information for customers to report Missing or Inaccurate navigation Radio Map Disc...
Read full bulletin
information.
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
This informational bulletin provides information on return or reimbursement of customer owned CDs, DVDs or Navigation...
Read full bulletin
Discs .
This technical bulletin advises to replace the radio if it blanks out and loses audio at times.
This Preliminary Information communication provides information to the technician that customers may inquire as to the...
Read full bulletin
availability of OnStar bluetooth on their vehicle. Technician should be advised that Vehicles with Regular Production Option Code (UPF or UWE) offer Bluetooth through the OnStar system.
This Preliminary Information communication provides information to the technician about vehicles that have a message on...
Read full bulletin
the radio ?maximum number of phones are currently paired to the vehicle?. Dealer should advise the customer this is normal operation of the vehicle due to the maximum number of five phones can be paired to a vehicle.
This informational bulletin provides information on If the radar does not see any vehicles, structures, or objects for...
Read full bulletin
15-25 minutes of driving, the system may think its blocked and display the ?Side Object Detection System Disabled? message.
This technical bulletin provides a procedure to update your apple product to the latest software version to correct a...
Read full bulletin
condition of infotainment system will not return to media after bluetooth call ends
This technical bulletin provides repair information on replacing a front door window regulator to correct a customer...
Read full bulletin
concern that when parking and turning off the vehicle, the radio continues to play after the driver or passenger door is opened. Technicians may also find DTCs U1530 or U1534 present.
This informational bulletin provides information on Inappropriate Warranty Claims Submitted for Damaged Radios and IPCs
THIS PRELIMINARY INFORMATION COMMUNICATES THAT WHEN CUSTOMER OR TECHNICIAN MAY INDICATE WHEN ATTEMPTING TO ADD A NEW...
Read full bulletin
TRANSMITTER TO A VEHICLE FOLLOWING THE ADDING TRANSMITTERS WITHOUT SERVICE PROGRAMMING SYSTEM PROCEDURE. THE PROCEDURE WILL NOT COMPLETE AND A MESSAGE "REMOTE LEARN PENDING" WILL BE DISPLAYED ON THE DRIVER INFORMATION CENTER. IN THE PAST TO PERFORM THE NEW TRANSMITTER PROCEDURE ONLY 1 PREVIOUSLY LEARNED TRANSMITTER WAS REQUIRED, THIS IS NO LONGER THE CASE NOW 2 PREVIOUSLY LEARNED TRANSMITTERS ARE REQUIRED AND PLACED INTO THE CUP HOLDER. IF THIS NEW PROCEDURE IS NOT FOLLOWED, THE "ADDING TRANSMITTERS WITHOUT SERVICE PROGRAMMING SYSTEM" CANNOT BE PERFORMED. THE TECHNICIAN WILL BE FORCE TO ADD A TRANSMITTER USING SERVICE PROGRAMMING SYSTEM.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO...
Read full bulletin
VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN.
Read full bulletin
THE VEHICLE'S XM RADIO ONLY HAS XM PREVEIW CHANNELS.
THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO REMOVE THE TRANSPORT MODE ON MESSAGE DISPLAYED IN THE DIC DUE TO...
Read full bulletin
VEHICLES SHIPPED OVER LONG DISTANCES OUTSIDE THE U.S. AND CANADA.
Tires & Wheels
22 bulletinsThis service bulletin provides information on Tire Sidewall Irregularities.
This service bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for GM...
Read full bulletin
Vehicles.
This service bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all...
Read full bulletin
repairs requiring balance and Road Force measurement.
This service bulletin provides information for dealers/technicians on Vibration Shortly After Tires are...
Read full bulletin
Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel).
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for tire pressure monitoring (TPM) system concerns.
This service bulletin provides information for accurate tire pressures that ensure the safe handling and appropriate...
Read full bulletin
ride characteristics of GM cars and trucks.
This service bulletin provides information for dealers/technicians on Tire/Wheel Characteristics (Vibration, Balance,...
Read full bulletin
Shake, Flat Spotting) of GM Original Equipment Tires.
This informational bulletin provides information for dealers/technicians on Use of Nitrogen Gas in Tires.
This informational bulletin provides information on Wheel Alignment Specifications, Requirements and Recommendations for...
Read full bulletin
GM Vehicles.
This informational bulletin provides information for dealers/technicians on Tire Radial Force Variation (RFV).
This informational bulletin explains the wheel Road Force balancers and what they can do for customer concerns.
This informational bulletin provides information on mcgard wheel locks and if the key ever fractures that they will...
Read full bulletin
replace it via the website provided.
This informational bulletin provides information on the temporary tire flat spotting condition.
This informational bulletin provides information on the proper mounting paste to apply to tires when mounting and...
Read full bulletin
balancing them to prevent conditions like Vibration Shortly After Tires are Mounted/Preventing Vibration from Wheel Slip (Tire Sliding on Wheel)
This Informational bulletin outlines the recommendations for aluminum and chrome wheel refinishing.
This informational bulletin provides information on Non-Design Intent Wheel Lock Nuts and Lug Nuts.
This informational bulletin provides information on the temporary tire flat spotting condition.
Brakes
15 bulletinsThis service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin advises about the possible issues that may occur when using a scotch brite pad or highly abrasive...
Read full bulletin
disk on gasket sealing surfaces or reused parts.
This service bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This service bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber and...
Read full bulletin
strut due to fluid leak.
This informational bulletin advises about the possible issues that may occur when using a scotch brite pad or highly...
Read full bulletin
abrasive disk on gasket sealing surfaces or reused parts.
This informational bulletin advises the possible issues that may occur using a scotch brite pad or highly abrasive disk...
Read full bulletin
on gasket sealing surfaces or reused parts.
This preliminary informational bulletin provides information regarding the normal characteristic of instrument panel red...
Read full bulletin
brake light intermittently comes on.
This informational bulletin provides information for cleaning brake dust off of aluminum or chrome wheels.
This informational bulletin provides information on installing the correct tires for vehicles with the condition of...
Read full bulletin
under hard acceleration at higher speeds, the traction control light will flash. Or, they may come in for ABS or general handling/braking concerns.
This informational bulletin provides information on brake rotor cover removal at Pre Delivery Inspection (PDI).
This Preliminary Information communication provides information to the technician the steps needed to diagnose and...
Read full bulletin
repair the vehicles that may have unwanted or phantom phone calls. Technician will need to determine what type of call the customer is having that is unwanted. The vehicle may receive an incoming call just like any other phone. Typically the customer will hear the phone ringing in the vehicle. This scenario also includes incoming Bluetooth calls. One type of unwanted call can be made if the key pad is faulty the OnStar system will try to make a blue button call for shorted voltage in the circuits. The OnStar module could have an internal fault and produce a ″Phone Unavailable″ audio message also it may have a Diagnostic Trouble Code U1500 or B1000. Refer to diagnostics for the Diagnostic Trouble Code making sure to follow any applicable Bulletins or Preliminary Information sheets. A “Ready” or “OnStar ready” audio message heard while driving. In some cases it has been found that the customer is inadvertently pressing the ″push to talk″ button on the steering wheel controls. On rare occasions, other issues in the steering column or Steering Wheel Control system may induce this concern.
This informational bulletin provides information to dealership personnel on diagnosis and replacement of shock absorber...
Read full bulletin
and strut due to fluid leak.
HVAC & Climate
6 bulletinsThis service bulletin provides information to diagnose batteries that have set for a long period of time and/or cold...
Read full bulletin
weather climates and testing those batteries.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
This service bulletin provides information to dealership personnel on a new refrigerant (R1234yf) for A/C service.
This informational bulletin provides information for information on passenger presence sensing system (PPS or PSS)...
Read full bulletin
concerns with custom upholstery, accessory seat heaters or other comfort enhancing devices.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
This informational bulletin provides information to diagnose batteries that have set for a long period of time and/or...
Read full bulletin
cold weather climates and testing those batteries.
Air Bags & Safety
5 bulletinsThis Preliminary information communicates assistance in locating the Rear seat belt comfort guides in the parts catalog.
This Preliminary information communicates assistance in locating theRear seat belt comfort guidesin the parts catalog.
This service bulletin provides information on availability for a seat belt extender.
THIS PRELIMINARY INFORMATIONAL BULLETIN PROVIDES A PROCEDURE TO REPOSITION THE FRONT SEAT BELT LATCH PLATE FOR CONCERNS...
Read full bulletin
REGARDING THE SEAT BELT WEBBING OR LATCH PLATE COMING TWISTED.
THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON LOCATING AND RECONNECTING AIRBAG CONNECTORS THAT ARE NOT FULLY...
Read full bulletin
SEATED TO CORRECT A CUSTOMER CONCERN OF AN AIRBAG WARNING LAMP ILLUMINATED, OR ONE, OR MORE, AIRBAG DTC(S) SET.
Software & Calibration
5 bulletinsThis service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This service bulletin provides technicians with updated information to help identify the differences between what is...
Read full bulletin
considered a fluid leak, and what is considered fluid seepage.
This informational bulletin provides technicians with updated information to help identify the differences between what...
Read full bulletin
is considered a fluid leak, and what is considered seepage.
Hybrid & EV
2 bulletinsThis service bulletin provides information on AGM batteries that require less frequent charging in storage.
This service bulletin provides information on AGM batteries that require less frequent charging in storage.
Suspension
1 bulletinThis technical bulletin provides a procedure to perform an alignment to the rear hub assembly by adding shims between...
Read full bulletin
the hub and knuckle.
Steering
1 bulletinThis preliminary information bulletin provides information for diagnosing a power steering fluid leak at the fluid...
Read full bulletin
reservoir.