2007 BMW Z4 TSBs

when placing the key against the steering column.

illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.

illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.

The ""Service Engine Soon"" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is ""late"", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well."

Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.

The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.

A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.

The customer of an affected vehicle may fail to pass an I/M test due to a non-compliant 17digit vehicle identification number (VIN) stored in the DME (Digital Motor Electronic). The VIN read out and displayed on the state test printout does not match the actual VIN of the vehicle. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it is possible that only the last 7 digits of the VIN were entered into the DME, and positions 4 through10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.

An occasional ticking or rattling noise from the camshaft hydraulic valve lifters (HVA) may occur during cold engine starts, due to frequent short-distance driving, or the noise may occur for an extended period of time even though the engine is at operating temperature. Improved parts were phased into production beginning on 10/1/2008 and fully implemented on November 31st 2008.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut

During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.

INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015

SYMPTOMS SUCH AS ERRATIC ENGINE OPERATION AND LONGER STARTING TIMES. *PE

THIS IS A PROGRAMMING ISSUE. *RM UPDATED 1/4/12. *PE UPDATED 4/24/12. *PE

*RM

THE SERVICE ENGINE SOON LIGHT MAY ALSO BE ON WITH A LACK OF ENGINE POWER. *RM

THIS IS DUE TO MOISTURE ACCUMULATION. *RM

THIS SITUATION MAY OCCUR AFTER DRIVING FOR SOME TIME WITH THE ENGINE ALREADY AT FULL OPERATING TEMPERATURE. IF THE IGNITION IS CYCLED, THE ENGINE THEN USUALLY PERFORMS NORMALLY. *PE UPDATED 2/7/11. *PE UPDATED ON 06/09/2011. *KB UPDATED 8/10/11. *PE UPDATED 1/11/13. *PE

This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.

ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.

The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the "Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".

The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""

The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""

The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""B5116_ECSPPL2."""

Please read this Service Information bulletin in its entirety, the content has been completely updated. designates changes to this revision SUBJECT Front Passenger Air Bag Seat Occupancy Sensor (OC3) Mat: Limited Warranty Extension to 15 years Without Mileage Limitation. INFORMATION BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the Supplemental Restraint System's (SRS) front passenger air bag seat occupancy sensor (OC3) mat on certain model BMW vehicles to: 15 years without mileage limitation as determined by the vehicle's original in-service date. This ""component-specific"" limited warranty extension applies to defects in materials and workmanship. This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. No immediate repair is required unless the BMW vehicle is currently experiencing this problem. This extended limited warranty coverage does not apply to vehicles affected by the following Recall Campaign: Recall 13V-564: E90, E91 Front Passenger Air Bag Seat Occupancy Sensor MatRecall 13V-564: E60, E61,E65, E66 Front Passenger Air Bag Seat Occupancy Sensor MatSI B65 08 14Recall Campaign 13V-564: Replace Front Passenger Air Bag Seat Occupancy Sensor (E60, E61, E65, E66)Recall 13V-564: E65,E66 Front Passenger Air Bag Seat Occupancy Sensor Mat (E65, E66)Recall 13V-564: Front Passenger Air Bag Seat Occupancy Sensor Mat for Sport Seat (E60, E61, E65, E66)Recall 13V-564: E53 Repair Front Passenger Air Bag Seat Occupancy Sensor MatThe extended limited warranty coverage also does not apply to: ??Vehicles with other seat options, and ??E60 (M5) vehicles Note: Please refer to SI B65 75 06 for the limited warranty extension information that applies to previous models. Customer Notification Letter - VIN and Component-specific Warranty Extension Even tho

THIS IS CAUSING THE BATTER TO NEED TO UNDERGO AN ENERGY DIAGNOSIS. *KB

WHERE IT IS NECESSARY TO REPLACE THE RIGHT OR THE LEFT SIDE FUEL LEVEL SENSOR DUE TO A FAILURE, THE ENTIRE PUMP AND HOUSING OR DELIVERY UNIT (SUCTION JET ASSEMBLY) DO NOT NEED TO BE REPLACED AS WELL. IN SOME CASES, EPC DOES NOT SHOW THAT THE REPAIR KIT IS AVAILABLE SEPARATELY IN THE ILLUSTRATION, BUT IT IS AVAILABLE IN THE PARTS DESCRIPTION. ALL MODELS. NO MODEL YEARS LISTED. *PE

A PART REPLACEMENT AUTHORIZATION MUST BE OBTAINED BY SUBMITTING A TC CASE IN PUMA BEFORE ANY OF THE FOLLOWING DSC COMPONENTS ARE REPLACED UNDER WARRANTY FOR THE VEHICLES LISTED IN THE MODEL SECTION OF THIS BULLETIN: DSC CONTROL MODULE, DSC HYDRO UNIT, AND YAW RATE SENSOR. NO MODEL YEARS LISTED. *PE

A REPAIR HARNESS FOR THE FRONT SEAT SAFETY BELT TENSIONERS AT THE BELT RETRACTORS MAY HAVE BEEN IMPROPERLY INSTALLED. *PE

The customer states that when the vehicle is started, or the ignition switch is turned on, there is a clicking/popping noise coming from the dash area. CAUSE Mis-alignment of the fresh air/recirculation flap gears.

WHEN TURNING A SLIP/STICK EFFECT IS CREATED ON THE LINING AND STEEL DISCS INCORPORATED IN THE DIFFERENTIAL CLUTCH CAUSES A GRINDING NOISE. *RM

*RM

*RM

Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.

INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.

Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.

WATER MAY ENTER THE LAMP. *RM

*RM

MODEL E90, E91(3 SERIES);E92, E92 (3 SERIES); E60 (5 SERIES); E60 (M5); E63, E64 (6 SERIES); E63, E64 (M6); E65, E66 (7 SERIES); E70 (X5); E83 (X3); AND E85, E86 (Z4). *PE

*RM

irritating to the customer; or it is not possible to locate certain addresses, for instance:

irritating to the customer; or it is not possible to locate certain addresses, for instance:

*RM UPDATED ON 4/24/2013. *KB

*PE UPDATED 7/8/09. *PE MODELS E82, E88 PRODUCED FROM START 2000 AND E71 PRODUCED FROM START 2000. UPDATED 7/21/10. *PE MODELS X6, E89, Z4 FROM START OF PRODUCTION. UPDATED 11/1/10. *PE MODELS F01 AND F02 FROM START OF PRODUCTION. UPDATED 1/3/11. *PE

*RM