2020 Bmw X6 TSBs

extended to 15 years/150,000 miles, as determined from the original in-service date.

Voltage supply The Service Engine Soon light is on with the following DME Fault Code: 21B209 - Starter alternator / belt for 48V system (OSA_RIEMEN_RISS): Belt betweenCombustion engine and starter generator torn And/or one or more of the following other issues are also occurring: Noise in the area of the belt drive. Odor from the engine compartment. Smoke formation in the area of the belt drive. Drive belt damaged or prematurely worn. Torn drive belt.

Check Control message (ID 166): Top up coolant.

Voltage supply The Service Engine Soon light is on with the following DME Fault Code: 21B209 - Starter alternator / belt for 48V system (OSA_RIEMEN_RISS): Belt betweenCombustion engine and starter generator torn And/or one or more of the following other issues are also occurring: Noise in the area of the belt drive. Odor from the engine compartment. Smoke formation in the area of the belt drive. Drive belt damaged or prematurely worn. Torn drive belt.

The affected units may activate a sporadic red-colored Check Control Message.

may be heard.

Traces of coolant leaking from the expansion tank of the low temperature cooling system.

Noises may occur dynamically (creaking/knocking) when weight is shifting upon the seat Noises may also occur when activating the seat motors.

when placing the key against the steering column.

A low coolant warning might also be displayed (CC Message ID166).

coolant loss when opening the low temperature cooling system reservoir (engine cold). The following fault code may also be stored in the DME: 20A201 - Charge air cooling system: Coolant pump protective function activated due to dry running Symptom 2*: The air conditioning may have low cooling output with the following fault stored in the IHKA: 80120A - Compressor: Shut down due to overpressure in refrigerant system. Symptom 2 is an additional symptom related to Symptom 1. Diagnose the IHKA fault with ISTA test plans if it is the only fault stored (if no DME faults are stored related to coolant loss, this bulletin repair does not apply).

when placing the key against the steering column. Note: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected.

A low coolant warning might also be displayed (CC Message ID166).

Check Control message (ID 166): Top up coolant.

The new ISTA Version is also able to be used in case of a Remote Software Upgrade (RSU) programming failure to get the customer car reprogrammed on site. In case of a Remote Software Upgrade failure, the engine start is prevented for safety reasons until the vehicle is programmed correctly. Most of the errors occur when only one control unit fails to program correctly.

When performing an engine oil service on vehicles equipped with a N63M, N63B or S63M engines; the ETK states to use "Set oil filter element" P/N 11 42 5 A33 C42 or P/N 11 42 5 A33 C43. The part numbers are not available at the moment.

and alternator.

Noises may occur dynamically (creaking/knocking) when weight is shifting upon the seat Noises may also occur when activating the seat motors.

The label shows the oil viscosity.

and alternator.

when placing the key against the steering column.

placing the key against the steering column.

The affected unitsmay activate a sporadic red-colored Check Control Message.

and the vehicle maynot start when placing the key against the steering column.

and the vehicle may not start when placing the key against the steering column.

and the vehicle may not start when placing the key against the steering column.

via the remote starting system (Remote Engine Start), the seat heating on the driver's side is not activated.

via the remote starting system (Remote Engine Start), the seat heating on the driver's side is not activated.

faulty hydraulic valve were installed in the vehicles. The affected unitsmay activate a sporadic red-colored Check Control Message.

and the vehicle may not start when placing the key against the steering column. Note: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected. Software error in the BDC (Body Domain Controller) module.

certain Model Year 2020 BMW vehicles that were produced between March 10, 2020 and June 1, 2020. Do not deliver to a customer, a New, Certified Pre-Owned or Used vehicle subject to a Delivery Stop, until the vehicle is repaired. Do not use or sell replacement equipment/parts subject to a Delivery Stop. The nuts holding the catalytic converter to a bracket in the engine compartment may become loose. Over time, this may lead to damage to the exhaust system. The nuts on the catalytic converter bracket in the engine compartment have been incorrectly torqued (19 Nm instead of 28 Nm).

Traces of coolant leaking from the expansion tank of the low temperature cooling system. Aluminum corrosion in the charge air intercoolers, or in the radiator for the low temperature cooling is causing an unfavorable chemical reaction to the coolant.

service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing.

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

headlight failure" (CC message 127) or "Headlight range control failure" (CC message 100). In conjunction one of the following faults codes MUST be stored for this bulletin to apply: 805A0D control unit: Headlight range control stepper motor driver failure (left frontal light module) 805A0E control unit: Adaptive Headlights stepper motor driver failure (left frontal light module) 805B8D control unit: Headlight range control stepper motor driver failure (left frontal light module) 805A0E control unit: Adaptive Headlights stepper motor driver failure (right frontal light module) This only affects vehicles with a current I-level below S18A-20-03-524. Software error in the FLM02 (Frontal light electronics module-Right or left).

replaces SI B17 02 20 dated March 2020. Premature breakdown of the coolant with gassing in the low temperature cooling system.

damaged if it contacts the air conditioning (AC) compressor pulley.

Technicians may notice this fault logged during a diagnostic session: Fault code: Control module: Fault Text: 160021 DME Crankshaft sensor: general loss of synchronism Environmental conditions are vehicle speed 0 (stationary) and engine speed less than 1500 rpm. There is no customer-facing symptom nor related check control message displayed. Phantom/pseudo fault due to unsuitable DME software. Background: After parking the vehicle and turning off the engine both DME control units go into sleep mode at different times. The DME of cylinder bank 2 ("secondary") goes into sleep mode first The DME of cylinder bank 1 ("primary") is still awake and can experience a reduction in signal voltage for the crankshaft sensor signal This signal change can mistakenly be evaluated as a skipped crankshaft sensor cog by the DME. If the engine is started while the primary DME is still awake this causes a brief loss of synchronization with the secondary DME. Fault 160021 is logged after three (3) consecutive engine starts with this momentary loss of synchronization. Note: Starting the engine after the primary DME has also gone into sleep mode will avoid the loss of synchronization.

indicator lamp (MIL) and/or a different issue the following faults may also be stored in the Digital Motor Electronics (DME). Fault code Control module Fault code text 213A2B DME Increment wheel adaption faulty This situation is not associated with any drivability complaints and only affects vehicles built with a Factory I-level of 19-07-500 and later. An unfavorable DME diagnostic calibration may cause the fault code to be stored. In most circumstances this will cause the MIL to be illuminated.

noise does not disappear despite the attempts to regenerate the brake a repair is required.

There is an engine speed-dependent noise heard through the speakers during audio playback. Software error in the Receiver Audio Module (RAM) control unit.

a consultation that the M Compound (standard equipment) and M Carbon Ceramic (optional) brakes are high-performance brake systems which are designed for sporty dynamic driving styles. As a side effect of the highest possible brake performance customers are likely to hear noises due to the extremely resilient materials.

One of the following faults may be stored in the digital motor electronics (DME) either as part of diagnosing a different issue; and-or an illuminated malfunction indicator lamp (MIL).

There is a possibility of contamination in the engine.

errors detected within PDC sensors. The warning indicates parking assistance featureshave limited functionality while the errors continue to be detected. Following faults may be stored 8031BA Ultrasonic Sensor Rear Side Left Software Error 8031CO Ultrasonic Sensor Rear outer left Software Error 8031AE Ultrasonic Sensor Rear Outer Right Software Error 8031A8 Ultrasonic Sensor Rear Side Right Software Error 8031B4 Ultrasonic Sensor Rear Middle Right Software Error 8031C6 Ultrasonic Sensor Rear Middle Left Software Error 8031CD Ultrasonic Sensor Voltage Supply Sensors Back: Short Circuit 8031CC Ultrasonic Sensor Voltage Supply Front: Short Circuit 8031CA Ultrasonic Sensors Front Extraneous Noise

workmanship has been extended to 10 years / 120,000 miles as determined from the original first in-service / deliver date.

miles as determined from the vehicles original in-service / first delivery date.

Also, one or more of the following error memory entries below may be stored in the Basic Central Platform(BCP) module. 80424A Remote control receiver at the front (FBD5 VM): Programming defective 80424B Remote control receiver at the rear (FBD5 HM): Programming defective 80424C Remote control receiver at the front left (FBD5s VL): Programming defective 80424D Remote control receiver at the front right (FBD5s VR): Programming defective 80424E Remote control receiver at the rear right (FBD5s HR): Programming defective 80424F Remote control receiver at the rear left (FBD5s HL): Programming defective

2021 BMW vehicles that were produced between August 13, 2019 and December 11, 2020. Do not deliver to a customer, a New, Certified Pre-Owned or Used vehicle subject to an emissions recall, until the vehicle is repaired. Do not use or sell replacement equipment/parts subject to an emissions recall. The 12 V batterys dual storage system (DSS) may contain a software error which intermittently causes a continuous resetting of the microcontroller and communication failure. The error is displayed by a red Check Control message.

This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.

Visible stitching on first row sport seat. Third seat row backrest Bowden cable routing and length change.

The following fault codes are stored during a vehicle test: 80419A - Left high-beam headlight: Short circuit and/or 8041A5 - light outputs: Number of permitted short circuit cycles exceeded

internal relay.

produced between September 28, 2021 and October 8, 2021. The issue involves the Active Crash Safety Module (ACSM) sensor.

As a result, the 12-volt battery becomes discharged and may cause a no-start condition.

That one provides an imprecise voltage measurement, which the main controller interprets as a fault.

another controller.

As a result, the 12-volt battery becomes discharged and may cause a no-start condition.

In the instrument cluster, the red air bag warning light lights up permanently. One of the following fault codes is stored in the ACSM (air bag control unit): 930949 - Knee airbag, driver: short circuit to negative terminal 93094F - Knee airbag, front passenger: short circuit to negative terminal 93094C - Knee airbag driver's side: Resistance too great 930952 - Knee airbag, front passenger: Resistance too great.

That one provides an imprecise voltage measurement, which the main controller interprets as a fault. For the driving cycle, the customer may lose the display in either mirror and the Lane Change Warning function and, if installed, other functions such as- Side collision warning; Lane Change Assistant; Steering and Lane Control Assistant; Emergency Lane Assistant Hands Off 60 Assistant.

In the Instrument cluster, the red air bag warning light lights up permanently. One of the following fault codes stored in the ACSM (air bag control unit): 930949 - Knee airbag, driver: short circuit to negative terminal; 93094F - Knee airbag, front passenger: short circuit to negative terminal.

produced between September 28, 2021 and October 8, 2021. The issue involves the Active Crash Safety Module (ACSM) sensor.

a software error which intermittently causes a continuous resetting of the microcontroller and communication failure.

reason with all the vehicle's doors and windows closed.

Due to the orientation of the LED module, moisture may enter the LED module, causing corrosion.

System (DSS) is disconnected from the electrical system via an internal relay.

The connection between the LED module and light tube inside the headlight is damaged.

from the outside using the remote control: The doors lock The alarm system is not activated The side mirrors (when the function is activated) do not fold in.

from the outside using the remote control: The doors lock. The alarm system is not activated. The side mirrors (when the function is activated) do not fold in.

front 12-volt power socket plug. Alternatively, it will only operate when constant downward hand pressure is maintained. A design change was intended to reduce short circuits and blown fuses. When the plug adapter is inserted, the center contact pin may not make proper contact with the center pin of the power socket plug.

front 12-volt power socket plug. Alternatively, it will only operate when constant downward hand pressure is maintained. A design change was intended to reduce short circuits and blown fuses. When the plug adapter is inserted, the center contact pin may not make proper contact with the center pin of the power socket plug.

Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. In some cases, the relay is stuck closed and a fault is set. In these circumstances: A crash shutdown of the DSS does not occur The power distribution box is supplied with power until the DSS is fully discharged.

Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery.

Design change to reduce short circuits and blown fuses.

Media Graphics Unit), there is a new protection mechanism against tampering. If one or more of the following components needs to be replaced, the secure connection between them must be re-established: MGU TCB Telematic Communication Box (ATM-02) RSE Rear Seat Entertainment and/or KOMBISP18 instrument cluster Prior to re-establishing this connection, an electronic certificate must be created in the BMW backend for importing into the Vehicle. After the replacement of one of the mentioned Modules, the Control Module needs a valid certificate for it to communicate with the other Modules.

Normal functionality may possibly return after a sleep cycle or a battery reset. This affects vehicles with: Integration level S18A-18-11-5xx Live Cockpit Professional (option code 6U3) including the instrument cluster High 4.1. While the Kombi is not working properly the rest of the system is working properly. The customer can still use the Central Information Display (CID) for items such as entertainment settings, Driver Experience settings, etc, utilizing the I drive controller. The telephone functions are not affected. Unfavorable software at system start-up.

Software error in the Advanced Telematics Module 2 (ATM2).

This may include: Calls in the BMW Assistance app (Concierge Service) Vehicle data and status in the BMW ConnectedDrive app Remote services Remote 3D View Real Time Traffic Information (RTTI) Weather News Software error in Advanced Telematics Module 2 (ATM2).

movement detector and the tilt alarm sensor system cannot be deactivated by pressing the lock button on the remote control / BMW display key twice. The second button press on the radio remote control / BMW display key is not detected. Customer may have to press the button 3 times to deactivate the interior movement detector and tilt alarm sensor. CAUSE Software error in the control unit of the roof function center (FZD).

Dual Storage System (DSS) is disconnected from the electrical system via an internal relay. In some cases the relay is stuck closed and a fault is set. In these circumstances: A crash shutdown of the DSS does not occur The power distribution box is supplied with power until the DSS is fully discharged

Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery. The Display Key Digital Key and the Digital Key Card are not affected. Electrostatic discharge puts the remote control key into a deep sleep. Various situations can lead to an electrostatic charge which is often not recognized by the customer. For example walking over carpet wearing shoes that have a hard rubber sole positive and negative charges are exchanged. The sole accumulates a negative charge and an electrostatic charge develops before touching the remote control key.

Design change to reduce short circuits and blown fuses.

Software error in the Advanced Telematics Module 2 (ATM2).

This may include: Calls in the BMW Assistance app (Concierge Service) Vehicle data and status in the BMW ConnectedDrive app Remote services Remote 3D View Real Time Traffic Information (RTTI) Weather News Software error in Advanced Telematics Module 2 (ATM2).

available for approximately 30 seconds after head unit start-up. Fault code B7F490 "Control unit reset" is present in the RAM (Receiver Audio Module).

illuminated even though the washer fluid reservoir is full. There are no faults stored in the system for the washer fluid level switch. A non-approved washer fluid was used that is silicone-based. Silicone-based fluids are not compatible with the contactless capacitive level sensor. Fluids that contain a silicone additive are normally colored other than blue.

active air flap is obstructed or blocked.

The noise does not occur when the rear seat backrest is folded down.

Thisicon will appear in the CID when this function is activated.

Wind noise 2. Excess water entry

Usage of the Highway Assist function (option code 5AX) is not possible.

produced between October 26, 2022 and May 8, 2023.

produced between March 1, 2023, and March 7, 2023. A metal stamping error during production, on a small amount of the affected vehicles.

following customer complaints: KAFAS camera system deactivates itself, due to system restrictions that are not clear to the customer KAFAS camera system cannot be activated due to system restrictions that are not clear to the customer Road signs are sporadically not detected.

Due to supply chain limitations, certain vehicles were produced without a CID with touch function and and without Reversing Assistant.

Alternatively, it will only operate when constant downward hand pressure is maintained.

Alternatively, it will only operate when constant downward hand pressure is maintained.

Alternatively, it will only operate when constant downward hand pressure is maintained.

Alternatively, it will only operate when constant downward hand pressure is maintained.

All or some of the system functions maybe inoperative. The following fault will be stored: 481CC6.

Refer to attachment for details. This only affects vehicles with the Merino leather.

Due to supply chain limitations, certain vehicles were produced without a CID with touch function and without Reversing Assistant.

headrests.

Wind noise, and 2. Excess water entry.

Due to supply chain limitations, certain vehicles were produced without a CID with touch function and and without Reversing Assistant.

The activation menu in the BMW iDrive is missing.

the automatic wiper mode selected, the wipers may activate.

second-row seat bottom, backrests and/or headrests.

operations.

operations.

(aka knee bolster) of either front seat.

Control with Stop & Go (ACC) function is activated.

the automatic wiper mode selected, the wipers may activate. The wipers' sweep movement can potentially damage the wiper blades.

the automatic wiper mode selected, the wipers may activate. The wipers' sweep movement can potentially damage the wiper blades.

FaultB7F8F9 HU-H: Reset will be stored in the HU-H3.

acoustic signals) may also have failed.

This can be reproduced with all audio sources as well as telephone and voice output.

with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.

2) The device switches off due to over temperature (built-in device protection).

key was inside the vehicle.

longer available, a black screen is shown in the Control Display, the system works again after a short interruption.

with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 3 (HU-H3, also called MGU) superseded the NBT-EVO starting with certain MY2019 vehicles with option code 6U3 Live Cockpit Professional or 6U2 Live Cockpit Plus. This uses map North America LIVE. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.

When the vehicle is parked in a parking spot with line markings, it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side, passenger side or both.

(e.g., YouTube, Spotify, etc) on the connected mobile phone. This affects Samsung mobile phones (e.g., Galaxy S20 / S21) with the Android 11 operating system.

Information Display (CID).

preview images at times.

satellite.

preview images at times.

satellite.

When the vehicle is parked in a parking spot with line markings, it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side, passenger side or both.

The navigation is no longer available. A black screen is shown in the Control Display.

black and then starts up again after a short time with the message "Start navigation system". This only occurs during navigation guidance when the "3D building" function is used Software in the Head Unit High (HU-H3).

ConnecedDrive apps are no longer available in the head unit. Software in the Head Unit High (HU-H3).

Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.

When the vehicle is parked in a parking spot with line markings, it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side, passenger side or both. Side view camera loose fitment in the exterior mirror bracket, causing changes to the top view image.

Central Information Display (CID) when the Surround View is activated.

Insulation material underneath the speaker may become loose. The situation may become even more noticeable on those vehicles where the dashboard area is cleaned using a vacuum cleaner.

Control Message (CCM) is displayed sporadically. All or some of the system functions maybe inoperative.

The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.

in the instrument cluster the head-up display or in the CID (Central Information Display) is very long. This can occur when browsing/scrolling through lists in the audio menu switching radio stations or albums. Software in the Head Unit High (HU-H3).

The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). When the vehicle is parked in a parking spot with line markings it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side passenger side or both. The arrow identifies the line which is shown as not parallel or straight alongside the vehicle. Side view camera loose fitment in the exterior mirror bracket causing changes to the top view image.

The customer states that the vehicle locks itself when the last door was closed even though the remote control/display key was inside the vehicle. Sporadic interference causes the vehicle to revert to "outside detection" of the vehicle remote control instead of "inside the vehicle detection" which is where the key was located.

This situation may be worse in vehicles which are regularly waxed in th e area of the door jamb.

may hang down and appear loose.

It serves only as a diagnostic resource in troubleshooting complaints from the roof area. This bulletin and the associated attachments are designed to provide one single diagnostic resource for troubleshooting all known issues related to the panoramic sunroof of BMW Sports Activity Vehicles which have quality improvement measures already in place.

Depending on the vehicles equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.

This situation may be worse in vehicles which are regularly waxed in the area of the door jamb. Note: This service information bulletin contains diagnostic and repair information which was previouslyincluded in an NED test plan that has been removed.

the driver and/or passenger side.

As a result, the "lock after starting to drive" function of the doors may not have been activated again.

BMW AG has issued a Delivery Stop (effective September 16, 2022) on a small number of Model Year 2022 - 2023 BMW vehicles that were produced on July 26, 2022. There is potential for water ingress via the roof antenna housing.

illuminate to alert the driver when it should.

D90D81-Sunblind rear driver (LIN): Missing LIN-slave D90D84-Sunblind rear passenger (LIN): Missing LIN-slave 8049B2-Sunblind rear driver (LIN): Line interruption 8049B6-Sunblind rear passenger (LIN): Line interruption 8049B3-Sunblind rear driver (LIN): Button jammed 8049B7-Sunblind rear passenger (LIN): Button jammed Possible misuse of the electric door sunshade(s).

Acoustic abnormality in the area of the recirculated air flap (recirculation flap closing and opening severaltimes). The above may occur individually or in combination.

It serves only as a diagnostic resource in troubleshooting complaints pertaining to the doors, windows, and mirrors. This bulletin and the associated attachments are designed to provide one single diagnostic resource for troubleshooting all known issues related to the door, windows, and mirrors of BMW Sports Activity Vehicles which have quality improvement measures already in place.

may hang down and appear loose.

This situation may be worse in vehicles which are regularly waxed in the area of the door jamb.

switch.

characteristic curve, no standardization exists and 030220 - SHD: System not standardized and 030295 - invalid characteristic curve, no standardization exists and 0302A0 - Service history: System not standardized. During operation, the sunroof may have lost initialization due to extended activation of the switch.

warm to the touch on long journeys with the interior "Heating on". The air ducts may not be properly connected, this allows heated air to leak out in this area. The foam material that seals between the ducts may be out of position, not held by the mounting adhesive and squashed allowing for an air leak.

bunching up during operation or may hang down and appear loose. This bulletin only applies to vehicles with an Alcantara headliner. The Alcantara material may be too thick to operate correctly in the panoramic sunroof frame.

or using foot motion via Comfort Access; the tailgate will not open completely. The tailgate will release, open a small amount, and stop as shown below: A software error in the automatic tailgate control unit (HKFM).

not have sufficient coolant corrosion protection.

not have sufficient coolant corrosion protection.

not have sufficient coolant corrosion protection. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as "Open" when checked either in AIR the "Service Menu" of DCSnet (Dealer Communication System) or with ISPA NEXT.

After carrying out the vehicle test, one or more of the stored faults indicate that the operation of the front bottomactive air flap is obstructed or blocked. Thoroughly inspect the front bottom air flap, when applicable, remove any contamination that is found caught inand between the bottom air flaps (aka blinds) and/or the housing.

However, due to a missing parameter, this does not work and can cause disruption in BMW ConnectedDrive services in areas with insufficient network coverage.

.

illuminated in the instrument cluster. The vehicles has no operating failures; only the MIL is illuminated.

illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch.

with one or more of the following faults stored: 138207- Active cooling damper control (AKKS), top: blockage at warm ambient temperature 21B043- Active cooling damper control (AKKS), top: blockage at all ambient temperatures 138222- Active cooling damper control (AKKS), above: positional deviation error detected at warm ambient temperature 138209- Active cooling damper control (AKKS), top: Control deviation at all ambient temperatures 13822B- Active cooling damper control (AKKS), top: Control deviation at all ambient temperatures 21B042- Active cooling damper control (AKKS), below: blockage at all ambient temperatures 138206- Active cooling damper control (AKKS), bottom, blockage at warm ambient temperature 138225-Active air-flap control, bottom: top limit position not detected 138224-Active air-flap control, bottom: bottom limit position not detected Multiple potential issues may be the cause, including: 1. Faulty active air flap(s) (Upper and/or lower) 2. Software error in the DME 3. Debris or blockages from outside influence (non-warranty) 4. Information error memory that does not require a repair 5. For G20 only- Detached lower active air flaps

or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no warning lights or Check Control messages. CAUSE Unevenly worn or incorrect fitment tires are installed on the vehicle or the factory-filled transfer case oil does not meet BMW specifications.

are not operating up to customer expectations.

returned to customers without making them aware of the change.

vehicles may receive new functionality or modifications in their features.

This SIB gives an overview how to identify these vehicles and how to proceed in case of a customer complaint.

changes to vehicle functionality that will result from each update.

This SIB gives an overview how to identify these vehicles and how to proceed in case of a customer complaint.

may receive new functionalities or modifications in their features with a new Software Update.

(RSU) is not possible in his/her vehicle, though the Remote Software Upgrade menu is available in the vehicle and a download was performed by the vehicle or the BMW Connected App.

Upgrade (RSU) is not possible in their vehicle, though the Remote Software Upgrade menu is available in the vehicle and a download was performed by the vehicle or the BMW Connected App.

With the introduction of RSU, customers now can update the vehicle software by themselves.

After a restart normal functionality is restored. Software error in the KOMBI (Instrument Cluster).

been extended to 15 years / 150,000 miles as determined from the original first in-service / delivery date.

boots.

collectively under analysis.

the data does not match the maintenance schedule.

the data does not match the maintenance schedule.

that have new operating parameters. This service information bulletin details the operation of the new style seats.

boots.

This bulletin is information only, no claim information intended.

Check control message can be verified by checking key reader information or performing the Check control message history service function.

Check control message can be verified by checking key reader information or performing the Check control message history service function.

miles as determined from the original in-service date

For this condition, the following fault is stored in the DME: 190302 - fuel tank ventilation and scavenging air system, micro-leak: leakage more than 0.5mm For: Model vehicles other that the ones listed above, or for EVAP faults related to a large leak, after confirming that the fuel filler cap is fitted properly, then, proceed to follow the corresponding test plan

The vent outlet temperatures vary by 25 degrees Fahrenheit or more (38 F to 60 F +) without changing any climate control settings.

For this condition, the following fault is stored in the DME: 190302 - fuel tank ventilation and scavenging air system, micro-leak: leakage more than 0.5 mm.

listed above were produced without the integrated touch screen function.

The vent outlet temperatures vary by 25 degrees Fahrenheit or more (38 F to 60 F +) without changing any climate control settings. In some cases the air conditioning may have stopped blowing cold air altogether.

The vent outlet temperatures vary by 25 degrees Fahrenheit or more (38F to 60F +; 3 to 15 + Celsius) without changing any climate control settings.

In rare cases, if the vehicle is locked using the remote control key and the fuel filler door is pushed closed simultaneously, the fuel door can enter a locked state that cannot be unlocked.

The fuel filler door material can swell in wet conditions causing the filler door to stick.

The fuel filler door material can swell in wet conditions causing the filler door to stick.

when parking, maneuvering)with a large steering angle, the front end can be slightly axially misaligned. This can be felt (jerking)/ heard via an acoustic acknowledgement (clunk) as seen at the 11 second mark of the video. See attached video V36 01 21.

1. A one-time thump sound at the start of movement Shortly after the steering column starts moving, retracting, or extending, a one-time thump noise is heard. See attached video V32 03 23 2. Humming noise while steering column extends in the axial direction. The sound is only heard when the steering column is extended, not when the steering column is retracted. When the steering column starts to move in the extended direction, the humming noise can be heard. See attached video V32 04 23

Background: Steering intervention helps keep the vehicle in the lane if the system detects that a lane marking has been crossed. The steering intervention can be noticed on the steering wheel and can be manually overridden at any time.

the steering wheel.

height adjustment.

height adjustment.

height adjustment.

fails when interior cabin temperatures rise above 122 degrees F (e.g., parked outdoors on hot day). Faulty self-diagnosis of the steering column control unit.

too strong (severe), which can create an uncomfortable feeling for the driver. Background: Steering intervention helps keep the vehicle in the lane if the system detects that a lane marking has been crossed. The steering intervention can be noticed on the steering wheel and can be manually overridden at any time. Software error in the KAFAS (camera-based driver assistance system) control unit.

intermittently inoperative including: On-board Computer (BC) button on turn signal stalk (BC button shown at left) Radio displays Menu button Turn signal displays Arrows on multifunction steering wheel MFL thumbwheel control.

were produced between June 16, 2020, and December 13, 2022. Due to a software failure, there is the possibility that the transmission does not go into "sleep mode" if the car is turned off.

The sensors for recording the gearshift lever position and for inhibiting inadvertent gearshifts are integrated in the control electronics.

into "sleep mode" if the car is turned off.

Drivetrain". In addition, the following information is shown on the Central Information Display (CID): "You can continue to drive. No roadside assistance necessary. To avoid subsequent damage, arrange an appointment with your Service Partner".

various sporadic concerns regarding the rearview camera and the surround view (top view) camera images in the CID (Central Information Display).

When reverse gear is selected or the rear view camera is activated sporadically no image is displayed on the Central Information Display (CID). If the ignition is cycled off and back on the function is restored. Software error between the head unit and the rear-view camera.

When reverse gear is selected or the rear view camera is activated sporadically no image is displayed on the Central Information Display (CID). If the ignition is cycled off and back on the function is restored. Software error between the head unit and the rear-view camera.

ID code 00042: Brake system. Additional notes: Avoid abrupt braking as far as possible. Drive at a moderate speed. Have it checked by your nearest Service Center. ID code 2046: Braking force assistance. Additional notes: Braking force assistance failure. Higher pedal force required for vehicle deceleration. Drive at a moderate speed. Have it checked by your nearest Service Center.

Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.

brakes applied, noticeable at low speeds. The vehicle must be moving.

Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.

"Brake fluid service due since 12/2001" is displayed in the instrument cluster although the vehicle is only a maximum of 1 year old. Software error in the KOMBI (Instrument Cluster).

BMW of North America LLC has issued a Delivery Stop (effective October 24 2019) on a small number of Model Year 2020 BMW X6 vehicles that were produced in the date range shown above. In extremely rare instances dimming of the tail lamps in the "Welcome mode" and "Goodbye mode" could cause the left or rear tail lamps and/or brake lamps to not illuminate. It is unlikely that the left and right tail lamps will not illuminate simultaneously.

v. BMW of North America, LLC. The Court has granted final approval of the settlement. Note: This updated bulletin (10/2023) is a notice that the Class Action Settlement was finalized on September 22, 2023. This is NOT a notice of a Recall or Service Action. Class Allegations The plaintiff in the lawsuit alleges that the front cupholders in certain model year 2019 through 2022 BMW X5, X5 M, X6, X6 M, or X7 vehicles are permeable to spilled liquids that may seep through the cupholders onto components, which in turn, may result in the illumination of the Supplemental Restraint System (SRS) warning light along with displaying a corresponding Check Control Message (CCM). BMW NA expressly denies any wrongdoing alleged in the complaint and does not admit or concede any actual or potential fault, wrongdoing, or liability.

In the instrument cluster, the red air bag warning light lights up permanently.

In the instrument cluster, the red air bag warning light lights up permanently.

District of California.

backrests may not properly align between the two seats.

Some possible customer concerns are: Vehicle does not avoid objects in its path tires or wheels contact the curb reversing Assistant only works for a short distance.