2014 Bmw X5 TSBs

(ELW) now includes more Model vehicles.

limited warranty for defects in materials and / or workmanship has been extended to 25 years without mileage limit as determined from the original first in-service / delivery date.

The following fault codes may be stored in the DDE: 24CE00 Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 Charge air hose monitoring in idle: Charge air hose fallen down 290900 Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation

There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE

plaintiffs in the following class action: Isley, et al. v. Bayerische Motoren Werke Aktiengesellschaft and BMW of North America, LLC. The Settlement Benefits are effective and available on and after February 9, 2022. Note: This bulletin is a notice of a Class Action Settlement Service Campaign benefits that are now available.

plaintiffs in the following class action: Isley, et al. v. Bayerische Motoren Werke Aktiengesellschaft and BMW of North America, LLC.

when placing the key against the steering column.

A low coolant warning might also be displayed (CC Message ID166).

when placing the key against the steering column. Note: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected.

high pressure fuel pump (shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date.

permitted filtered actuation duration 24BB00 correction too high zero-quantity adaptation injector cylinder 2: permitted filtered actuation duration 24BF00 correction too high zero-quantity adaptation injector cylinder 3: permitted filtered actuation duration 24BD00 correction too high zero-quantity adaptation injector cylinder 4: permitted filtered actuation duration 24C000 correction too high.

not charge the vehicle.

malfunction indicator lamp (MIL) on. The intake manifold (intake system) is found to have thermal deformation or damage. Melt through may also be found in the area of the EGR inlet and randomly around the intake system.

(and repair) (SI B11 17 18) applies and shows open on an Eligible Vehicle then this bulletin does not apply. The vehicle demonstrates a power loss while driving and illuminated malfunction indicator lamp (MIL).

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear.

Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on.

The Service Engine Soon (MIL) lamp is on with the following fault codes stored in the DME: Misfires While there are various possible causes a possible cause might be that one or more fuel injectors are leaking/defective.

In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.

replaces SI B01 05 18 dated January 2018. Engine starts poorly (hard starting) rough idle and misfires.

The engine malfunction warning is illuminated and one of the following fault codes are stored in the DME shortly after programming the vehicle or with a customer complaint.

One of the following complaints may be reported The engine runs erratically; The engine causes vibrations when running; Grinding noise from the engine compartment when engine is running.

The Selective Catalyst Reduction (SCR) control module can make an error when calculating the DEF line pressure. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.

The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

If the vehicle is driven with long engine idle phases followed by full throttle accelerations, engine (spark) knocking could occur and result in internal engine damage.

Due to an issue with the exhaust-gas recirculation (EGR) valve, the malfunction indicator lamp (MIL) lights up and vehicle engine may begin jerking or have sporadic idle fluctuations. Additionally, the fault memory may read the following fault codes: * 255C00 - EGR controller, position control: Valve too wide open/negative control deviation * 272F00 - Exhaust-gas recirculation valve, plausibility: mechanically faulty, near open position * 272E00 - Exhaust-gas recirculation valve, plausibility: mechanically faulty, near closed position * 290900 - Air system, air to EGR exhaust mass flow, plausibility measured air mass compared to calculated air mass too high * 257E00 - EGR controller, position sensor, signal: Interruption or short circuit to ground * 255D00 - EGR controller, actuation: Interruption * 255B00 - EGR controller, position control: Valve too wide closed/positive control deviation * 290B00 - Air system, air to EGR air mass flow, plausibility: measured air mass compared to calculated air mass too low * 240500 - Exhaust-gas recirculation control, control deviation: Air mass too high/negative control deviation * 240400 - Exhaust gas recirculation control, control deviation: Air mass too low/positive control deviation * 273600 - EGR controller position, long-term drift: Position deviation too high (current/new condition)

With an outside temperature below 14F, brake booster vacuum may be reduced after a cold start. The non-return valve in the vacuum line to the brake booster may stick at temperatures below 14F. Sufficient vacuum supply is available again at the brake booster only after the vehicle is driven (approximately 1/4 mile).

The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system

The following conditions may exist: Charging is either stopped mid-charge or will not initiate. The corona ring around the charge port blinks red. Check engine light is turned on. Faulty software up to and including ISTA/P 3.58.3 (F025-16-03-504)

A Delivery Stop has been issued for fifteen F15 vehicles produced from March 3, 2016 to March 28, 2016. In these vehicles the cooler lines for the automatic transmission may have been routed incorrectly. In such instances, the cooler lines may come into contact with the crankshaft vibration damper (pulley). Affected vehicles can be identified with a ""Vehicle Comment"" in DCS Warranty Vehicle Inquiry or ISPA Light with the description: ""A Delivery Stop has been issued for this vehicle. Dealers must ensure that all Campaigns are completed before retail delivery to the customer. See Service Information Bulletin B17 01 16."""

bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."

After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).

dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.

available in many parts of the US market. The high pressure EGR cooler could become filled with soot particulate to the point that exhaust gas flow and cooling efficiency are significantly reduced. This could result in the Service Engine Soon light coming on with EGR control / Air mass faults being stored in the DDE.

This could result in incorrect engine torque and mismatched ignition parameters with the possibility of internal engine damage.

A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.

14 dated December 2014, designates changes to this revision. SUBJECT NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak . The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm. CAUSE: Contamination of the NVLD pressure switch diaphragm and/or the contamination of the NVLD dust filter.

Remote key battery in service significantly less (under a year) than expected two-year life-span. Remote key will NOT: * Open/close vehicle door locks * Start engine (except when held directly against steering column) CC message ""Battery of remote key empty (ID:00067)"" displayed Fault memory entry ""BDC 804415- ID Transmitter: Battery under-voltage"" stored Remote key battery has been drained, possibly by elevated standby current (faulty capacitor). "

One or more of the following situations may occur: * The customer operates the windshield wiper washer system, which activates the headlight washers automatically. The windshield wipers operate two times and then stop after the headlight washers activate. The windshield wipers then have to be turned on again manually. * After the customer stops the wipers by pressing the button on the wiper control lever, the wipers remain approximately 15 cm above the lowest position and do not go into the normal park position. * The customer states that the control LEDs for rear seat heating (option code 496, rear seat heating) do not light up after switching on the rear heated seats, using the button. * When the key remote is placed in front of the instrument cluster and the brake pedal is applied to start the vehicle, a Check Control Message, ""No remote control/engine cannot be started,"" is displayed. The engine starts once the key is moved to another location. CAUSE Software error in the BDC (Body Domain Controller)"

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.

Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.

??Oil leaking from the Rain/Light Sensor (RLS). Note: This oil serves as a separation medium between the RLS mounting gel pad and the windscreen. The oil ensures damage free disassembly in case of repair. CAUSE The oil that serves as the separation medium of the Rain/Light Sensor (RLS) gel pad and the windscreen leaks out. Expose the Rain/Light Sensor (RLS) and properly clean the area of all oily residue. Note: The separating oil usually leaks only once from the pad at the RLS. Due to the small oil quantity in the gel pad, additional oil leakage is not plausible. Leaking oil does not impair the function of the RLS.

* On board computer and navigation system goes black or resets. * The engine can only be switched off by pressing the START/STOP button three times (Emergency STOP) * Various Check Control messages are displayed. * At a minimum the following fault code is present: D91C86 - CAN message, status functional safety (ST_FSSY): Timeout-BDC * Additional fault messages may also be displayed Software error in the central gateway of the Body Domain Controller (BDC) control unit. Note: Parts replacement does NOT provide a solution!

After the vehicle is exposed to prolonged temperatures under -9C (15.8F) and is then driven a long distance when temperatures are above -9C (15.8F), the check engine light may be illuminated. The following fault may be stored in the Digital Diesel Electronics (DDE) 805256 - Active tank filling level sensor, signal: echo fault In low temperature under -9C (15.8F) a layer of ice may form in the active tank. This can result in an incorrect level measurement after the vehicle is driven.

A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. 2C4E00 - SCR system: System error and poor urea/water mixture quality detected 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software

After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.

One or more of the following fault codes are stored in the DDE: 29FB00 - DeNOx system, warning and switching off scenario: Warning level 1 280D00 - NOx-Sensor upstream DeNOx-catalytic converter, signal NOx: NOx-Signal invalid for too long 280F00 - NOx-Sensor downstream DeNOx-catalytic converter, signal NOx: NOx-signal invalid for too long 29FC00 - DeNOx-system, warning and switch-off scenario: Warning level 2 CD840A - FA-CAN bus: Control unit switched off from bus (Bus off) CD94C7 - Message (RQ_PWR_EL_EPS, 234.0.2, FX): Messaging from EPS failed CD951C - Message (AVL_STMOM_DV_ACT_AVL_FORC_GRD, 49.0.2, FX):Messaging from EPS failed CD9536 - Message (DIAG_OBD_SCR, 0x3EE, FA): Messaging from SCR control unit failed CD953A - Message (ST_FFLV_SCRA, 0x40B, FA): Messaging from SCR control unit failed CD953C - Message (ST_RESO_SCRA, 0x8A, FA): Messaging from SCR control unit failed CD942B - Message (DT_GRDT, 0x1AF, A): Messaging from transmission control unit failed CD946B - Message (ST_GRB_ECU, 0x39A, FA): Messaging from transmission control unit failed CD9487 - Message (RQ_TORQ_CRSH_GRB, 0xB0, A): Messaging from transmission control unit failed CD94B9 - Message (DISP_RPM_ENG_DYNS, 0xF8, A): Signal(s) in message invalid CD94BA - Message (DISP_RPM_ENG_DYNS, 0xF8, A): Messaging from transmission control unit failed CD94C3 - Message (DIAG_OBD_GRB, 0x396, FA): Messaging from transmission control unit failed CD94DC - Transmission control unit, communication: Transmission communication via A- CAN and FACAN failed CD94ED - Message (DT_DISP_GRDT, 0x3FD, FA): Messaging from transmission control unit failed CD950D - Message (RQ_TORQ_CRSH_GRB_2, 0xA0, A): Signal(s) in message invalid ? CD950F - Message (RQ_TORQ_CRSH_GRB_2, 0xA0, A): Messaging from transmission control unit failed ? CD9549 - Message (DIENSTE-ID2=19 request MSA function, 0x598, FA): Message from transmitter control unit (EGS_EL) failed.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting

Unable to start" Is Displayed. With the engine running, the Start/Stop button is pressed and the engine stops. If the Start/Stop button is pressed again (without opening the door), and the customer has his/her foot on the brake pedal, the engine starts. An erroneous check control message "Remote control missing. Unable to start" is then displayed in the instrument cluster and Central Information Display (CID). Software error in the Body Domain Controller (BDC)

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting

A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: * 26F500 - SCR system, efficiency: Efficiency too low * 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of ""Incorrect diesel exhaust fluid"" may be displayed with ""no start scenario countdown"" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. * 2CE400 - SCR system: System error and poor urea/water mixture quality detected * 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high * 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 * 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software"

The Service Engine Soon lamp is on (MIL) with the following fault stored in the DDE: 29EB00 - EGR cooling, plausibility: Exhaust-gas recirculation cooler bypass flap faulty or cooler efficiency too low CAUSE Unfavorable DDE software.

The Service Engine Soon light is on with the following fault stored in the Selective Catalyst Reduction module (SCR). z 805220 - Delivery module, system pressure, pressure build-up is too low. This fault is very likely to be stored at temperatures below 32F / 0C if the vehicle is programmed using ISTA/P 3.54.1 or 3.54.2. Unfavorable SCR software

The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts

The engine will not start at times at very low outside temperatures (-4F/-20C and colder); however, the battery state of charge is correct and the starter turns the engine over properly. This starting difficulty is most likely to occur after shutting the engine off briefly for 5 or 10 minutes, such as when refueling. The following faults are most likely stored in the DME: N20 engine: ? 1B5202 - Terminal 15N_1: No voltage? 1B5302 - Terminal 15N_2: No voltage ? 1B5402 - Terminal 15N_3: No voltage N52T engine: ? 1B5102 - Terminal 15N_3: line from CAS, electric: short circuit to earth ? 1B5501 - Terminal 15N: No voltage ? 1F0601 - Terminal 15N from CAS, switching delay: Switches too lateN55 engine: ? 1B5202 - Terminal 15N_1: No voltage? 1B5302 - Terminal 15N_2: No voltage ? 1B5402 - Terminal 15N_3: No voltage In addition, other engine electronic power supply-related faults could be stored for components such as VANOS solenoids, camshaft sensors, engine oil pressure sensor, engine oil pressure control valve, engine oil level sensor, etc. At very low outside temperatures, low levels of moisture present inside the power distribution module (PDM) can freeze the internal micro-relay contacts.

When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut

The Service Engine Soon lamp (MIL) is on with either of the following nitrogen oxide (NOx) sensor faults stored: * 2B6200 - NOx sensor before DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity * 2B6300 - NOx sensor After DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity These stored faults would not cause a problem with engine performance. This NOx self-diagnostic routine is performed only after the engine has been shut off. In some situations, the diagnostic function of both NOx sensors can be too sensitive when sampling the residual exhaust gases, leading to an erroneous fault being set. Unfavorable DDE software diagnostics

A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: * 26F500 - SCR system, efficiency: Efficiency too low * 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. * 2CE400 - SCR system: System error and poor urea/water mixture quality detected * 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high * 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 * 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software.

During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.

safety-related defect or noncompliance exists in any motor vehicle or item of replacement equipment in the center's possession at the time of notification. In BMW NA's case, this notification would typically be made by the issuance of a Recall notification in the form of a Service Information bulletin (SIB) or transmission of a Dealer Communication System (DCS) Recall message. When a Recall Campaign is announced by BMW NA, centers must ensure that all Recalls on new vehicles and new items of replacement equipment are completed BEFORE delivery to the consumer. This means that centers may not legally deliver new motor vehicles or new items of replacement equipment to consumers with an open Recall. This also pertains to vehicles in the Certified Pre-Owned program, and to items of replacement equipment. Finally, BMW centers should not sell or use parts that have been recalled by BMW NA. Please follow the specific instructions provided by BMW NA on the return or disposition of the parts. designates changes to this revision SUBJECT Voluntary Emissions Recall Campaign 14E-A01: Replace Emissions Label. Certain 2014 model year F15 vehicles produced from March 13, 2014 through April 12, 2014. These vehicles are equipped with an ""emissions"" label with incorrect information pertaining to the model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery."

To turn the engine off when it is running, the start/stop button must be pressed several times. This error does not affect starting of the engine. Body Domain Controller (BDC) application software error BDC fault ""8040A9 - Start-stop button SST: Incorrect operation (pushed at an angle)"" is stored."

The Service Engine Soon lamp (MIL) is on with either of the following nitrogen oxide (NOx) sensor faults stored: * 2B6200 - NOx sensor before DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity * 2B6300 - NOx sensor After DeNOx catalytic converter, plausibility: Sensor self-diagnosis of sensitivity These stored faults would not cause a problem with engine performance. This NOx self-diagnostic routine is performed only after the engine has been shut off. In some situations, the diagnostic function of both NOx sensors can be too sensitive when sampling the residual exhaust gases, leading to an erroneous fault being set. Unfavorable DDE software diagnostics

Various engine performance symptoms could occur if the spark plug insulator becomes damaged: * The Service Engine Soon (MIL) may be on with rough running and misfire fault(s) stored. * Intermittent performance or rough running without a relevant DME fault stored. The spark plug insulator could be damaged in cases of combustion faults such as misfiring, ignition knock or super knocking conditions.

This Service Information bulletin replaces SI B13 07 15 dated August 2015. The DDE software release for the Engine Start-Stop (MSA) function is incomplete. As a result the (MSA) feature cannot be activated with the MSA On/Off switch.

The Service Engine Soon light comes on with either or both of the following faults stored in the DME memory: ? 12B701 - Oxygen sensor heating after catalytic converter, function: Internal resistance too high ? 12B801 - Oxygen sensor heating after catalytic converter 2, function: Internal resistance too high The engine operation and performance are not affected. The DME diagnosis for the post catalyst oxygen sensor(s) is too sensitive.

designates changes to this revision SUBJECT Service Engine Soon Light (MIL) Is On with SCR Faults Stored. The Service Engine Soon light is on with the following fault stored in the Selective Catalyst Reduction module (SCR). z 805220 - Delivery module, system pressure, pressure build-up is too low. This fault is very likely to be stored at temperatures below 32F / 0C if the vehicle is programmed using ISTA/P 3.54.1 or 3.54.2. F25 (X3) only: z 8051B0 - Metering line heating, power too high SCR module software error

Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.

The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.

The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement of the crankshaft position sensor 2. Replacement of the incremental sensor wheel on the crankshaft 3. Replacement of the crankshaft 4. Replacement of the crankcase (block) with pistons 5. Replacement of the engine assembly Due to slight tolerance differences with the new replacement hardware and the original learned crankshaft position, values could cause cylinder balance calculation errors by the DME. DME software (the incremental wheel adaptation cannot be cleared)

The blower in the third row of seats is not working and the fault code ""E70C32 - AC-LIN: Heating in third row of seats is not responding"" has been entered in the IHKA (Integrated Heating and Airconditioning, Automatic) control unit. CAUSE LIN BUS short or open circuit in wiring or connectors Blower motor, micro switch defective Control unit, A/C, for 3rd seat row defective."

There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.

Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."

The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.

INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015

designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.

An error in the calculation of the DEF line pressure by the SCR module software could occur at temperatures below 32F/0C. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.

designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

The following conditions may exist: Charging is either stopped mid-charge or will not initiate. The corona ring around the charge port blinks red. Check engine light is turned on. Faulty software up to and including ISTA/P 3.58.3 (F025-16-03-504)

Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2"

The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system

The blower in the third row of seats is not working and the fault code ""E70C32 - AC-LIN: Heating in third row of seats is not responding"" has been entered in the IHKA (Integrated Heating and Airconditioning, Automatic) control unit. CAUSE LIN BUS short or open circuit in wiring or connectors Blower motor, micro switch defective Control unit, A/C, for 3rd seat row defective"

Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.

A shudder or slight jerking can be felt when driving with the transmission in 7th or 8th gear and the engine speed is between 1,000 and 1,400 RPM. No related faults are stored and there are not any problems in the chassis systems or with the wheels and tires. This shudder or jerking could begin due to the characteristic power pulses of the N63T engine when it is in VVT mode at low engine loads.

Malfunction Indicator Lamp (MIL) is illuminated. The following codes may be stored in the fault memory of the battery management electronics (SME). 21F20D - SME, safety concept: Switch-off of switch contactors by safety circuit 21F1F6 - High-voltage battery, switch contactors: Switch-off after a fault Software bug: erroneous fault code stored in SME.

After performing repairs where the engine harness was disconnected and reconnected at the differential pressure and the exhaust pressure sensor, the following fault is then stored in the DDE: 28DE00 - Exhaust gas pressure sensor before Turbine, plausibility: exhaust gas pressure in front of turbine dynamically not plausible

Check Control message: Oil pressure warning. Stop carefully is displayed. There are no related faults to oil pressure stored in the DDE. Unfavorable DDE software application When operating during automatic engine start-stop function stop, it may be the case that the oil pressure is incorrectly determined to be too low, which triggers a CC message.

July 2014 What's New: Model - Removed models which no longer support BMW Assist functionality and added new models. Procedure - Add step requesting print out of ConnectedDrive Service Cockpit page Information - Add SI for ConnectedDrive Service Cockpit; updated the hyperlinks and email address for CD support team; deleted scenario for old CDMA unit which are no longer supported. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

added ? "Models" updated: Model Year G12 (7 Series) excluded from program ? "Procedure" updated: N63R engine added to 2016 Model Year G12 (7 Series) ? Attachment updated with G12 (7 Series) production date range for 2016 Model Year. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

When initiating gradual acceleration at between 40mph to 60mph, customer may experience some minor shuddering under acceleration. Some situations that may lead to this experience would be: Gradual depressing of the accelerator pedal Change in load (increase in road grade) Acceleration request by cruise control The following conditions must be present for this situation to occur: "Auto eDrive" driving mode selected Engine speed of approximately 1500 rpm Transmission in Drive, running in 7th or 8th gear, Low State of Charge (SOC) of high voltage battery. No fault codes are stored as a result of this performance issue. Stacking of tolerances in the driveline.

injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.

indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.

. The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600 C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The

The following performance issues may be noticed by the customer: CC-Message ""Drive faulty"" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF."

Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."

This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.

system goes black or resets.

(MIL) illuminated.

North America, LLC (BMW NA) is extending the limited warranty for the vehicles engine fuel injectors to:

replacement.

the following fault is stored in the Digital Motor Electronics (DME) fault memory:

capacity specification for all vehicles with the N63R engine and xDrive.

deteriorate prematurely causing any of the following: vacuum leak various fault codes related to mixture control stored in the DME customer complaints about rough idle speed Check Engine Light illumination.

ACCELERATING UNDER CERTAIN CONDITIONS DUE TO DME SOFTWARE ERROR. *MA

AND ILLUMINATION OF ENGINE MALFUNCTION LAMP (MIL) COMES ON, DUE TO SOFTWARE ERROR IN INSTRUMENT CLUSTER. MODEL 2011-15. *PE

DRIVING CAN CAUSE ENGINE INTERNAL DAMAGE, IN SOME VEHICLES. MODEL 2013-14 F15 (X5). *PE

*

*PE

*PE

TO ENGINE POSITION MANAGEMENT (EPM) UNFAVORABLE PARAMETERS IN DME SOFTWARE. *PE

This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.

Visible stitching on first row sport seat. Third seat row backrest Bowden cable routing and length change.

In the Instrument cluster, the red air bag warning light lights up permanently. One of the following fault codes stored in the ACSM (air bag control unit): 930949 - Knee airbag, driver: short circuit to negative terminal; 93094F - Knee airbag, front passenger: short circuit to negative terminal.

For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle Nitrogen Oxide (NOx) Sensor(s) to: 10 years/120,000 miles as determined by the vehicle original in-service date.

and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.

communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.

be supported by the cellular network provider starting February 2022. The decision to phase out 3G network technology was made at the discretion of the respective cellular carriers and lies beyond the control of BMW. Due to the phase-out, BMW Assist and ConnectedDrive services will no longer be supported after this date.

battery.

battery.

illuminated even though the washer fluid reservoir is full. There are no faults stored in the system for the washer fluid level switch. A non-approved washer fluid was used that is silicone-based. Silicone-based fluids are not compatible with the contactless capacitive level sensor. Fluids that contain a silicone additive are normally colored other than blue.

Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.

INFORMATION The ST1821 High Voltage Diagnostic Specialist Certification (HVS) is the next step in the E-mobility service strategy for BMW technicians.

2019.

bulletin supersedes SI B01 04 18 dated April 2018.

2019.

bulletin supersedes SI B01 04 18 dated April 2018.

The customer's vehicle does not start due to a totally discharged battery.

INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.

While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""

The low washer fluid warning light is illuminated even though the washer fluid tank is full. There are no faults stored in the system for the washer fluid level switch. CAUSE A non-approved washer fluid is used (fluids that contain a silicone additive, normally colored other than blue). INFORMATION The washer fluid level sensor is a contactless capacitive sensor. The sensor sends a low fluid level signal to the gateway module (FEM - Front Electronics Module or BDC - Body Domain Controller) which in turn displays a low washer fluid warning in the instrument cluster. The use of a ""non-approved"" washer fluid (silicone-based fluid) can cause the low fluid warning light to come on even when the reservoir is full. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates."

If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""

For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.

SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).

General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 30 14 dated December 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure . INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months.

Replace the seat module. Improve ground wiring connections on seat frame.

Due to a signal error from the oil level sensor, the vehicle could display an erroneous message indicating that an oil service is due after only a short distance has been traveled.

BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).

An incorrect refrigerant was used to fill the refrigerant circuit in the affected vehicles after assembly. AFFECTED VEHICLES This Service Action involves X5 or X6 (Only 8 vehicles) vehicles produced from January 16 to February 19, 2018. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in AIR, the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader. The affected vehicles will be identified with the description: 0064950100 B640318 Delivery Stop: Refrigerant Air Conditioning.

A headlight malfunction CC message is displayed for one or more of the following lights: -Daytime driving light -Turn indicator -Dipped headlight -Main beam The following fault codes in the FRM are stored: -800FC8 LIN bus, headlight driver module (TMS), left: communication fault -E58522 No message (status, exterior lights, front electronics 1, left, 0x1E0), receiver FRM, transmitter TMSL Software error in TMS 3 (headlight driver module AHL); a software I-level lower than 14-07-503 will cause the above situation to occur.

1. The LED headlight on one side malfunctions. 2. One headlight flickers on and off while driving (problem is sporadic). 3. The Check Control message indicates the parking light or driving light is defective. One or more of the following faults can be stored: 805980 Low-beam headlight defective 805981 High-beam headlight defective 8044BB Right-hand LED main light module (LHM2) implausible low-beam headlight function status 8044BA Left-hand LED main light module (LHM2) implausible low-beam headlight function status CAUSE The situation above is caused by a poor connection at the LED headlight connector or LED main light module.

A change in the job structure in ISTA causes the BDC to open the 30B relay unexpectedly.

Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.

Intermittently, the Central Information Display (CID) flashes off/on. Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher.

INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle through the iDrive controller, by entering the 20-digit enabling code manually.

If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software

Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.

* In very cold weather conditions (32F or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. Software error in TMS 3 (headlight driver module AHL, xenon headlight)"

The customer may experience one or more of the following complaints: * One or both headlights are aimed significantly too low (jammed lower limit). * No reference run is visible on the affected headlight when the ignition is turned on and the light switch is in the auto position. * No CCM (Check Control Message) is displayed when a headlight is faulty. CAUSE * TMS-3 (Headlight driver module AHL) coding error * Defective mechanism inside the headlight

INFORMATION Do not replace any parts. NOTE: First time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Check, with the vehicle connected to the diagnosis system ISTA. Refer to SI B65 30 09. Connect the vehicle to the diagnosis system ISTA and activate the navigation system. The code is entered when running the QC1 Pre-Delivery Check test module. Refer to SI B09 04 09. IMPORTANT: No programming is required. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately.

* In very cold weather conditions (32F or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. CAUSE Software error in TMS 3 (Headlight driver module AHL xenon light)"

The interior ambient light malfunctions with one or more of the following symptoms present: 1. The ambient light in the door trim lights up in the wrong color (LED module). 2. The ambient light is brighter on one side in the dash panel than on the other. 3. One of the ambient lights does not light up on the driver's side of the dash panel or door panel. 4. A group of ambient lights is malfunctioning. CAUSE One of the following could be the root cause: a. Remove the affected door trim panel for inspection per ISTA Repair Instruction 5141000, ""Removing and installing 1. An incorrect fit between the LED module and fiber cable 2. Connections on the LED modules in the door panel are not fitted correctly. 3. The LED module in the door panel and/or the dash panel is not locked correctly in the mounting bracket, or the fiber optic cable on the LED module is broken. 4. The BDC (Body Domain Controller) is missing initialization and automatic addressing of all LED modules."

When replacing a BDC control unit, terminal 15 is not recognized by ISTA and ISTA/P when the ignition is on. CAUSE Software in the BDC

designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months. "

INFORMATION The use of a ""non-approved"" washer fluid can cause the low fluid warning light to come on even when the reservoir is full. An analysis of parts returned to warranty has shown the sensor is operating correctly. Do not replace the reservoir with integrated sensor for these situations. We recommend using ""BMW Group approved"" washer fluid when servicing the vehicle or performing repairs on the windshield washer system. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates. If the correct washer fluid is being used, diagnose the system using normal troubleshooting with ISTA. A fault code may be stored if an electrical fault occurs in the circuit. PARTS INFORMATION Part NumberDescriptionQuantity83 19 2 406 220BMW WWS Cold Weather Concentrate 35% 55 GalAs needed83 19 2 361 205BMW Windshield Washer Concentrate 1 GalAs neededNote: As applicable, do not exceed your state's maximum for the allowable amount/percentage of ""Washer Concentrate"" that can be used when mixing the windshield washer fluid solution. WARRANTY INFORMATION The issue described in this bulletin is not a vehicle-related defect in materials or workmanship. If a vehicle repair is required as a result of this issue, it is are not claimable under a BMW limited warranty."

INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles ""arriving"" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed ""prior"" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2. "

INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. CAUSE When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.

Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.

The front passenger and both rear seat heaters do not work. The following fault codes are stored in the BDC (Body Doman Controller): D90C18 - LIN master I: Short circuit D90C1A - LIN master I: Communication faulty CAUSE One of the rear seat heater modules has an internal fault, which interrupts LIN bus communication.

According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."

designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

Changes made to the B370314 attachment. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Program Variable Damper Control (VDC) unit. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new VDC software improves the acceleration sensor accuracy in our vehicles, and it helps us to ensure superior product quality. Please implement the VDC Programming Service Action immediately. This Service Action will be in effect until March 2015. Thank you for your continuous support. Unfavorable tolerances for the wheel acceleration sensors' plug-in connections may result in deactivation and fault code memory entries and the VDC. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.

Changes made to the B370214 attachment. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Program Variable Damper Control (VDC) Unit. Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message. The vehicle then defaults to the conventional suspension.

INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016

HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"

INFORMATION For the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."

INFORMATION For the eligible vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."

If an NBT-EVO head unit is swapped into a different vehicle it will enter a locked mode once it recognizes a different VIN. This will set a fault in the Head Unit (NBT-EVO), Fault Code ""B7F87A: Burgler Actively Registered / Component Protection Active"" This will require REPLACEMENT of the head unit to restore operation. To prevent easy re-use of stolen Head units additional features are introduced with 11/15 ISTA/P software to bring NBT-EVO to a higher security level. In NBT-EVO the mechanism is called ""Trusted VIN"""

HVAC blower is not working. Condensation occurs even though blower is working. CC message ""Increased battery discharge"" - standby current violation may be displayed. Climate control unit (IHKA) software"

Intermittently, the Central Information Display (CID) flashes off/on. Voltage supply error from the Head unit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher

According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Front passenger seat occupancy detection transmitting fault (moisture)"" is stored. The fault may or may not currently be present. The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."

There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.

Front seat electric adjustment controls do not function. Electrostatic discharge damage the seat module.

What is new? Procedure section updated with video link as a repair hint. Front seat electric adjustment controls do not function. Electrostatic discharge damage the seat module.

two-year life-span.

cycling the ignition.

that has been designed exclusively for the BMW vehicles listed above.

electronics

fails.

with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.

with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 3 (HU-H3, also called MGU) superseded the NBT-EVO starting with certain MY2019 vehicles with option code 6U3 Live Cockpit Professional or 6U2 Live Cockpit Plus. This uses map North America LIVE. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.

Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.

The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.

This Service Information bulletin replaces SI B62 11 18 dated January 2019. Whats New: ? Warranty section - Programming information added. A small black spot remains on the Central Information Displays (CID) illuminated screen which does not go away after a key cycle or sleep mode.

INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!

There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.

""Comfort Access Restricted"" CCM (Check Control Message) is permanently displayed.. The CCM ID: D0h. The comfort access is functioning correctly. No comfort access aerial fault codes stored in the BDC (Body Domain Controller). Software error in the BDC"

Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).

While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software

SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.

HUD (Head-up Display) adjusted to the lowest position is no longer visible. Software in the instrument cluster.

SUBJECT Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed . Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Note: If Fault Code E1C440 ""Headunit Reset"" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H."

AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Incorrect SW calibration loaded after KOMBI replacement."

The DRL (Daytime Running Light) is off and cannot be switched on after importing the personal profile from another vehicle. The CID (Central Information Display) display shows that it is active. CAUSE Software error when importing the personal profile from a vehicle which has a different head unit

Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H

The height adjustment for the Head-up Display is not permanently stored in Personal Profiles for the remote control key used. When using a different remote control key, the height adjustment resets to the default value. Software error in the instrument cluster

After pressing the Start/Stop button, the Check Control message "Tire pressure check failed" appears briefly, as well as the corresponding light on the instrument cluster. These displays disappear after a few seconds. Software in the BDC (Body Domain Controller)

Due to a software error stored in the DSC control unit, a fault code memory entry is permanently stored. This fault is not displayed, nor can it be cleared using the BMW diagnostic tools. The fault code memory entry has no functional effect on the DSC control unit. This fault code entry may result in failing the OBD test when using a scan tool.

The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.

This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.

INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.

Due to a software error stored in the DSC control unit, a fault code memory entry is permanently stored. This fault is not displayed, nor can it be cleared using the BMW diagnostic tools. The fault code memory entry has no functional effect on the DSC control unit. This fault code entry may result in failing the OBD test when using a scan tool.

After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.

The door opens to the first stage and the Check Control Message (CCM) is displayed. Front or rear door lock Bowden cable cover and the door lock

When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.

The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!

INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.

The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H

The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 ""display backlighting and graphics PCB switched off"" stored. Kombi software."

The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error.

Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.

This Service Information bulletin supersedes SI B51 16 14 dated January 2015 designates changes to this revision SUBJECT Door Opens to First Stage While Driving. The door opens to the first stage and the Check Control Message (CCM) is displayed. This can affect any door. Automatic soft-close drive (Bowden cable lock)

INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the ""Attachment"" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received. "

designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015

SUBJECT Door Opens to First Stage While Driving. The door opens to the first stage and the Check Control Message (CCM) is displayed. This can affect any door. Automatic soft-close drive (Bowden cable lock).

HUD (Head-up Display) adjusted to the lowest position is no longer visible. Software in the instrument cluster

INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.

The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H

The Head-up Display information is no longer visible on the windshield. The Head-up Display has moved downwards to the lowest possible position and can no longer be adjusted to a higher position. Software error in the instrument cluster

NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes ""without a cash option"" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes ""without cash option"". UPDATE Install new map data."

HV charging is intermittently not possible. When charging problem occurs, a CCM 804 "Charging Not Possible" will be displayed. Affected vehicles may begin to charge if the charger plug is rapidly plugged/unplugged several times. Charging problem may be noticed consistently at same charging location, but not at others. KLE Software."

While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software

irritating to the customer; or it is not possible to locate certain addresses, for instance:

High 2 (NBT EVO) when:

the: Navigation system starts message is permanently displayed; or

irritating to the customer; or it is not possible to locate certain addresses, for instance:

Samsung S6 and the S6 Edge.

performing ISTA4 programming, there is no audio playback.

implausible outside temperature reading.

Information Computer (CIC) on certain MY2013 vehicles with option 609 (7/2012+).

randomly switches to BMW Apps (Pandora, Spotify, Audible etc.) with no input from driver or passenger.

*TA

*PE

CABLE COVER AND DOOR LOCK WOULD NEED REPLACING, AS NEEDED. MODEL 2013-15 F15 (X5). *PE

Depending on the vehicles equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.

illuminate to alert the driver when it should.

This situation may be worse in vehicles which are regularly waxed in the area of the door jamb.

Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.

The vehicle cannot be unlocked using the remote control key button. However, comfort access operates normally at the front door handles and the tailgate.

This situation may be worse in vehicles which are regularly waxed in the area of the door jamb.

during driving especially on uneven surfaces. Clicking noises or squeaking noises from the area of the tailgate. Or a popping sound coming from the area of the tailgate.

The door opens to the first stage and the "Door Open" indicator (pictogram) will indicate the door affected. This can affect any door. Automatic soft-close drive (Bowden cable lock). Soft-Close Automatic drive (SCA) locking levers are slow to respond to lock request.

INFORMATION The automatically dimming exterior mirror function on the passenger's side has been deleted from the Option Code 430 as noted above. The automatic dimming function will continue to be operational on the driver's side mirror and rear view mirror.

When the vehicle is in a transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle enters a sleep mode, there is a communication error in the BDC (Body Domain Controller) resulting in a failure to wake up the control unit. This Service Information will be updated in April 2014. Until then, follow the procedure outlined below.

Based on feedback from technicians, it can be difficult to identify the individual components included with sunroof repair kits. In some cases complete sunroofs are replaced, when a sunroof repair kit could have been used. This bulletin covers the contents of the sunroof repair kits in order to help you identify the correct repair for the vehicle you are working on.

The door opens to the first stage and the "Door Open" indicator (pictogram) will indicate the door affected. This can affect any door. Automatic soft-close drive (Bowden cable lock). Soft-Close Automatic drive (SCA) locking levers are slow to respond to lock request.

The central locking system locks and unlocks on its own when the vehicle is in motion. Software error in the Body Domain Controller (BDC).

Seal fitment mainly on the exterior mirrors, doors and window seals

When using the left or right turn signal, the turn signal light on the outside mirror does not operate. CAUSE The outside mirror light assembly has a pin pushed back and makes a bad contact.

One or both of the following may occur: 1. The sunroof becomes stuck during operation. 2. The sunroof cannot be opened or closed. The panoramic sunroof rear glass mechanism fails. The drive cable plate is either broken or bent.

When activating the rear window washers, the front washers briefly spray approximately 6-8 inches onto the windshield. Impulses from the washer pump are not dampened when in use.

If a replacement remote control key is disabled using ISTA, all Comfort Access features are inoperative, including Comfort Start. CAUSE BDC (Body Domain Controller) software error

When using the left or right turn signal, the turn signal light on the outside mirror does not operate. CAUSE The outside mirror light assembly has a pin pushed back and makes a bad contact.

After deleting transport mode during PDI (Pre Delivery Inspection-QC I), fault code ""8041A9 - Daytime running light lock active"" is present in the BDC (Body Domain Controller) and the DRL (Day Running Light) is switched off. CAUSE Software in the BDC"

The customer cannot see the rear door child safety locking lever. CAUSE Improper door latching mechanism installation (safety lock lever is hidden behind the sheet metal)

Affected vehicles have been identified as being delivered within the state of California, which requires a front license plate to be affixed. The SAV center must install the bracket to the front bumper in anticipation of affixing the license plate.

The customer may complain of wind noise and/or poor fitment of the door mirror seal. CAUSE The outside mirror seal locking tab shows poor fitment.

The customer may complain of poor rear window washing/clearing at the lower portion of the rear glass. CAUSE The rear wiper blade moves before there is a sufficient amount of washer fluid on the rear glass.

Sporadically, when the vehicle has been locked and is in sleep mode, the vehicle will not waken when trying to unlock the vehicle with comfort access from any door. The vehicle can be unlocked from the remote. After waking, the comfort access function is restored. Software fault in the BDC.

During and/or after heavy or prolonged rain, one or both of the situation(s) listed below may occur: ? Water leaks from various locations in the headliner. ? The footwell carpet is wet or soaked with water. Multiple root causes have been linked to this issue. One or more of the cause listed below may apply. The sunroof drain tube is: ? Not properly connected to the sunroof ? Twisted or kinked between the sunroof and where it exits the vehicle ? The sunroof drain is cut or torn above the headliner.

The front seats generate a squeaking noise upon entering or exiting the vehicle. The noise may also occur when repositioning on the seat or movement while driving. Aged/dried leather on the seat bottom cushion rubbing against the plastic side trim.

Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.

Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by ""condensation"" rather than a ""water leak"" into the headlight housing, there will be misting/condensation in ""both headlights."""

INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.

The door opens to the first stage and the ""Door Open"" indicator (pictogram) will indicate the door affected. This can affect any door. Automatic soft-close drive (Bowden cable lock). Soft-Close Automatic drive (SCA) locking levers are slow to respond to lock request."

When opening, a loud thump is heard as the rear window reaches the bottom of its movement. Window guide.

Wind noise 2. Excess water entry

Alternatively, it will only operate when constant downward hand pressure is maintained.

one side (inner rail).

position, a check control message (CCM) appears alerting the customer that the seat back is unlocked. The passenger's side (right rear 40% seat) of the 60/40 split 2nd row seat may intermittently not fully latch into position on one side (inner rail).

position, a check control message (CCM) appears alerting the customer that the seat back is unlocked.

side (inner rail).

All or some of the system functions maybe inoperative. The following fault will be stored: 481CC6.

v. BMW of North America, et al. The Court has granted final approval of the settlement. The Settlement Benefits are effective and available on and after February 9, 2022.

v. BMW of North America, et al. The Court has granted final approval of the settlement. The Settlement Benefits are effective and available on and after February 9, 2022.

The alarm (DWA) siren continues to activate after locking vehicle An ""unapproved"" device is connected to the On-Board Diagnostics (OBD) port of the vehicle. This keeps the Ethernet communication line active which triggers the alarm when the vehicle tries to enter sleep mode."

A high-pitched metallic clicking noise is heard from the front axle when taking off from a stop or during a load reversal (reverse to drive). The preset axial play in the input flange to pinion bearings of the front differential may create a metal-on-metal "crack" noise when load reversing.

ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.

The front seat (left or right) thigh support cover is loose. The thigh support cover is not fully clipped into place.

along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added "Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."

There are two related but separate issues (only one may be present at a time) during driving, especially on uneven surfaces: A. Clicking noises or squeaking noises from the area of the rear hatch. Or B. A popping sound coming from the area of the rear hatch. Bump stop height: A. Situation A - settling of the bump stops over time allows vibration, rattle of the hatch. B. Situation B - the bump stops may be adjusted too high, putting torsional stress on the hatch, causing flexing (popping) noises.

inoperative.

seat may restricted.

*PE

Injectors to 10 years/120,000 miles as determined by the vehicle's original in-service date.

the malfunction indicator lamp (MIL) on.

The vehicle may run rough or hesitate.

Customer complains of crackling noises coming from the fresh air grille for approx. 15 seconds when switching on the air-conditioning system. Refrigerant transition inside the evaporator.

An incorrectly displayed AdBlue (Diesel Exhaust Fluid refill range) CCM is shown on the Central Information Display. Improper instrument cluster software

Customer complains of crackling noises coming from the fresh air grille for approx. 15 seconds when switching on the air-conditioning system. Refrigerant transition inside the evaporator.

Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm

designates changes to this revision SUBJECT A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.

designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.

The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This varies based on outside temperature and humidity. CAUSE The A/C low-pressure lines and evaporator are starting to freeze up.

designates changes to this revision SUBJECT A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.

designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD

The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the ""fuel consumption, current"" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold."

The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.

An unusual whistling noise can be heard coming from the center vent area for approximately15 seconds after the A/C is switched on. CAUSE Evaporator in the A/C system

INFORMATION Inform the customer that the introduction of these expanded frequencies by the wireless mobile providers may be influencing reception quality. BMW is currently working with the wireless mobile providers in order to improve the quality of reception and help alleviate the issues that are caused by the wireless mobile expanded frequencies. Once we have more information about this situation this service information bulletin will be updated. Currently Satellite Radio is provided by SiriusXM for BMW customers via geosynchronous (GEO) satellites located roughly above the equator. This means that the satellite signal to some parts of the United States can come in at an angle as low as 32 degrees to the horizon. Due to this angle, buildings, hills, trees, highway sound blocking walls or other obstacles might block the satellite signal coming from reaching the vehicle receiver antenna and might cause audio cut outs, unless the wireless provider has installed terrestrial repeaters. Reception quality decreases the further north you travel, as the angle of the incoming signal gets smaller. Also adverse weather conditions might affect reception. At this time, in the event of a customer complaint or inquiry on interference noise: Do not replace any parts Do not program or carry out other work on the vehicle Explain to customer about the new Wireless Communications Service (WCS) signals When investigating Satellite Radio cutouts or a temporary loss of reception: Please compare to a similarly equipped vehicle. Keep in mind the roofline of the vehicle, size of the antenna (sharkfin) and location of the antenna on the vehicle will all affect the strength of the reception. Do not compare a Sport Activity Vehicle (SAV) with a high roofline mounted antenna to a different vehicle such as a coupe or convertible with a much lower mounting point of the antenna. Replace no parts Do not prog

labelled).

THEREFORE, THE LABEL MUST BE REPLACED. MODELS F15. MODEL YEAR 2014. *JS

illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch.

supersedes SI B61 23 15 dated April 2016.

supersedes SI B61 23 15 dated April 2016.

designates changes to this revision SUBJECT Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)

When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.

A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)

A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)

A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)

headlight lenses that is visible from outside.

by honking the horn, flashing the lights or on the map in the BMW Connected App) do not function after vehicle has been sitting for extended amount of time (In excess of 20 hours).

DOFF DURING DRIVING AND THE CONTROL CHECK MESSAGE IS INDICATING DEFECTIVE DRIVING LIGHT OR PARKING LIGHT. *PE

brakes applied, noticeable at low speeds. The vehicle must be moving.

Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.

A fault in the parking brake (EMF) switch could cause a Check Control message (Parking Brake Failure) to display. However, all braking functions, including the parking brake and switch continue to operate properly in this case. Affected vehicles in center inventory must not be delivered until the parking brake switch has been replaced. Parking brake switches for the F15 must be ordered VIN-specific. Refer to Service Information bulletin B61 20 13 for the part number and complete instructions. Parts for the F01 and F02 are not available at this time. An availability update will be provided by November 20 (1 week).

An electrical malfunction in the EMF (Electromechanical Parking Brake) switch can cause an erroneous Check Control Message to be displayed. The parking brake functions properly. EMF switch hardware error AFFECTED VEHICLES This Service Action involves F01, F02 and F15 vehicles which were produced from June 2013 to October 2013. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 658. If code number 658 has been punched out, the campaign has already been performed. If code number 658 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."

An electrical malfunction in the EMF (Electromechanical Parking Brake) switch can cause an erroneous Check Control Message to be displayed. The parking brake functions properly. EMF switch hardware error AFFECTED VEHICLES This Service Action involves F01, F02 and F15 vehicles which were produced from June 2013 to October 2013. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 658. If code number 658 has been punched out, the campaign has already been performed. If code number 658 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action."

A Delivery Stop has been issued on certain 2014 model year F15 vehicles produced on March 5, 2014. These vehicles may be equipped with incorrect top mount flanges (shock caps) on the rear axle. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at ports of entry will be repaired prior to dealer delivery. This bulletin will be updated with instructions and warranty information when parts become available. Please contact your field representatives if you have any questions. Affected vehicles are listed in the attachment to this bulletin and can be identified with a ?Vehicle Comment? in DCS Warranty Vehicle Inquiry or ISPA with the description: Defect Code 0033870100, Delivery Stop, Rear Shock Absorber, see SI B33 03 14.

Some rear shock absorbers may have been assembled with the incorrect guide support. These incorrect guide supports will cause a rattling noise within a low mileage.

When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.

MODEL F15 (X5). *PE

After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.

Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.

The Check Control message ""Drive: Stop carefully"" (CCM-ID: 569) is displayed. The following fault codes may be stored in the transmission EGS control module (GKEG3HY3): 44D663 - Position plausibility: Driver's choice N/P from D/R not executed CF1701 - Gear selector switch interface, communication failure CF17A1 - Message missing: receiver EGS (A-CAN), transmitter selector switch (A-CAN) EGS software diagnostic function"

When the reverse gear is selected, the automatic parking function (tilting of the door mirrors) does not work. CAUSE Coding error in the BDC (Body Domain Controller)

* Vehicle will not go into "eDrive" * No pertinent electric drivetrain fault codes to assist with diagnosis * "eDrive" may be greyed-out in the Central Information Display (CID) and is not selectable * MSA deactivation * 12 volt battery failure * Intelligent Battery Sensor (IBS) failure.

After engaging reverse gear, the reversing camera intermittently does not display a picture. However, after a key cycle, the reversing camera once again displays the picture. One or more of the following may be noticed on the display at different times: 1. Black screen 2. Blue screen 3. Grey striped screen Note: All the displays may be seen with or without an exclamation mark. CAUSE Software error in the camera control unit (TRSVC - Top Rear Side View Camera)

Intermittently the gear selector switch cannot be moved into the left sport or manual position. It is still possible to shift the vehicle from Park to Reverse, Drive or Neutral. Internal fault in the GWS

This Service Information bulletin supersedes SI B33 01 14 dated February 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Delivery Stop/Service Action: Check Rear Axle Differential. 1 A Delivery Stop has been issued on certain 2014 model year F15 and F3x vehicles produced from July 2013 to January 2014 because the final drive differential gears may not have been properly hardened. Vehicles held at the ports of entry are being inspected and/or repaired prior to center delivery. During this inspection and analysis of data, BMW of North America has documented a failure rate of less than one in two hundred. The affected vehicles are listed in the attachment to this bulletin; they are also identified with a ""Vehicle Comment"" in the DCSnet Warranty Vehicle Inquiry or ISPA as follows: ??Defect Code 0033840100, Delivery Stop: Rear Axle Differential; see SI B 33 01 14 The initial limited available stock of parts is reserved for vehicles that have already been sold and are in customers' hands (see Situation 2). Affected vehicles in center inventory must not be retailed or delivered until the rear differential has been replaced. 2 Certain 2014 model year F15 and F3x vehicles produced from July 2013 to January 2014 may have final drive differential gears that have not been properly hardened. These vehicles have already been sold and delivered to customers."

When no other fault codes stored. ? Customer has seen no performance issues. OR 2. When any of the following fault codes are stored. 44D141 - transmission monitoring: Clutch A and D implausible 44D0E1 - transmission monitoring: Clutch B implausible 44D191 - transmission monitoring: Clutch C and D implausible 44D151 - transmission monitoring: Clutch A and E implausible 44D0D1 - transmission monitoring: Clutch A implausible 44CFB1 - transmission monitoring: Clutch A, D and E implausible 44CFD1 - transmission monitoring: Fault pattern - gear monitoring implausible And possibly: ? Customer reports harsh shifting ? Check Control message ""Drivetrain malfunction"" Various"

Hesitant drive off, sluggish driving behavior. The Automatic Transmission (AT) switches into emergency mode and operates only in first gear, Manual shifting (+/-) in Sport Program (using both gear selector and/or shift paddles) is not possible. 44E257 - ""N6 speed sensor: Direction of rotation invalid"" is stored in transmission control module Transmission Control Unit (GKEG3HY) software"

There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants

When the vehicle is in transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle is in transport mode, to reduce power consumption, the software is designed to disable the outside antenna receiver from waking up the vehicle.

When the customer presses or turns the controller, there is no or a delayed response. This can sporadically occur. Software in the controller

There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.

INCOMPLETE, DUE TO THE VARIANTS AND SOFTWARE USED. MODEL 2008-2014.

This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via the Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance, and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.

This Service Information bulletin replaces SI B84 02 14 dated September 2018.

ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."

BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's.

The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.

axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.

CAUSE Steering column adjustment.

Creaking noise when raising or lowering the steering column position CAUSE Steering column adjustment

from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.

position

The internal thread of the wheel bolt wrench is incorrect at M8. AFFECTED VEHICLES This Service Action involves F56 vehicles according to VIN selection. First check if a Service Action label with a code number 64 is already attached to the B-pillar. If a code number 64 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.

Five (5) vehicles were produced with an incorrect Tire and Loading Information label. The label may not reflect the proper ""Cold Tire Pressure"" specifications for the vehicle. AFFECTED VEHICLES Only the vehicles listed below are affected by this action: VINsMYModelCurrent Address State5UXKR0C5XF0K588942015X5 xDrive35iNew Jersey5UXKR0C57F0K588982015X5 xDrive35iFlorida5UXKR0C54F0K589072015X5 xDrive35iMassachusetts5UXKR0C58F0K589092015X5 xDrive35iNew York5UXKR0C5XF0K589132015X5 xDrive35iVirginia"

MODEL YEARS 2014-15. *PE

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.

The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)

*TA

Humming or high-pitched vibrating noises can be heard inside the vehicle when the air conditioning (A/C) is switched on.

INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION