2006 BMW X3 TSBs

when placing the key against the steering column.

For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Radiator Grille Upper and Lower Active Air Flaps to: 15 years/150,000 miles as determined by the vehicle's original in-service date. 1. Air flap control (link) active, upper (G12, G30 and G32) 2. Air flap control (drive), active, upper 3. Air flaps, upper (assembly) 4. Air flaps, lower (assembly) For eligible MY 2017 BMW 530i (B460) vehicles that are currently registered in the State of California (CA) or a State that has fully adopted the State of California PZEV/SULEV regulation (CT, ME, MD, MA, NJ, NY, RI, and VT), the standard emission-related coverage for the Radiator Front Grille Air Vent Flaps is15 years/150,000 miles. This component-specific limited warranty extension applies to defects in materials or workmanship.' This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. A check control message or MIL (Malfunction Indicator Lamp) may be illuminated with faults stored related to the upper and/or lower active air flap(s). Potential causes include: Faulty upper air flap link (G12, G30, G32) Faulty upper air flap actuator (G01, G02, G12, G30, G32) Faulty upper flap assembly (G01, G02, G12, G30, G32) Faulty lower air flap assembly (G01, G02, G12, G30, G32) Software error in the DME affecting the upper flap (G01, G02 only) Or: Upon visual inspection, the passenger side upper active air flaps are either stuck open or closed, and they will not move and there are no faults stored for the active air flaps (With no check control message or check engine light or displaying)

when placing the key against the steering column. Note: Opening, closing and starting via the BMW Digital Key or the Digital Key Card are not affected.

illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.

A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.

The customer of an affected vehicle may fail to pass an I/M test due to a non-compliant 17digit vehicle identification number (VIN) stored in the DME (Digital Motor Electronic). The VIN read out and displayed on the state test printout does not match the actual VIN of the vehicle. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it is possible that only the last 7 digits of the VIN were entered into the DME, and positions 4 through10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut

A shudder or vibration can be felt under light acceleration or when driving at constant suburban speeds. This can be most noticeable in the 1700 - 2200 engine rpm range while in 3rd through 6th gears. No faults are stored in the EGS module. CAUSE Changes in the frictional properties of the automatic transmission fluid over time can lead to momentary slipping of the torque convertor lock-up clutch.

There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.

INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015

The Anti-lock Brakes (ABS), Brakes and Dynamic Stability Control (DSC) warnings are on and there may also be a ""Drivetrain Malfunction"" warning on in the Control Display. There is also an audible clicking noise coming from the transfer case actuator when cycling the ignition. The following fault codes may be stored: (DSC) 5F3A - Clutch gearbox-ECU: clutch is open - rear-wheel drive! (VTG) 5463 - Break mechanics (VTG) 5462 - Error actuator or increased power requirements for clutch (VTG) 5461 - Error actuator control Internal wear to the plastic gears of the transfer case actuator."

THERE ARE TROUBLE CODES STORED FOR THE CRANKSHAFT SENSOR. NO DRIVEABILITY ISSUES. *RM

*RM

THIS IS A PROGRAMMING ISSUE. *RM UPDATED 1/4/12. *PE UPDATED 4/24/12. *PE

THIS IS DUE TO MOISTURE ACCUMULATION. *RM

THIS SITUATION MAY OCCUR AFTER DRIVING FOR SOME TIME WITH THE ENGINE ALREADY AT FULL OPERATING TEMPERATURE. IF THE IGNITION IS CYCLED, THE ENGINE THEN USUALLY PERFORMS NORMALLY. *PE UPDATED 2/7/11. *PE UPDATED ON 06/09/2011. *KB UPDATED 8/10/11. *PE UPDATED 1/11/13. *PE

IN SOME VEHICLES HAVE INSUFFICIENT HEAT. E90, E91 (3 SERIES), E60, E61 (5 SERIES) 3/06 AND E83 (X3 SERIES) 9/08. *PE

SOFTWARE ERROR IN THE DME FOR THE TANK LEAK DIAGNOSTIC SYSTEM. MODELS E60, E61 (5 SERIES); E70 (X5); E71 (X6); E82, E88 (1 SERIES); E83 (X3); E90, E91, E92, E93 (3 SERIES). *PE

THE VANOS SOLENOID VALVE IS JAMMED OR STICKING. *PE

POOR THROTTLE RESPONSE; LACK OF POWER WHEN ACCELERATING; ENGINE MAY CRANK TOO LONG BEFORE STARTING; LOSS OF POWER AT IDLE OR WHEN SLOWING TO A STOP. E83 (X3) MODELS. *PE

MODELS E83, E85, E86, E70, E90, E91, E92, E93, E60 AND E61. *PE UPDATED 5/24/11. *PE

MODELS E60 (5 SERIES), E70 (X5 SERIES), E83 (X3 SERIES), E9X (3 SERIES). *PE

This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.

For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Leak Diagnosis Module with hose assembly (NVLD, shown) to: 15 years/150,000 miles as determined by the vehicle's original in-service date. For eligible MY 2017 BMW 530i Sedan and xDrive (B460) vehicles that are currently registered in the State of California (CA) or a State that has fully adopted the State of California PZEV/SULEV regulation (CT, ME, MD, MA, NJ, NY, RI, and VT), the standard component-related coverage for the NVLD is 15 years/150,000 miles. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks. Over time, the Leak Diagnosis Module (NVLD) (with connected hose) component material may fail, this can create a fine leak to develop in the Evaporative Emission Control System (EVAP). Should this occur, corresponding fault codes will be stored in the DME memory and the MIL (Malfunction Indicator Lamp) will illuminate.

In the instrument cluster, the red air bag warning light lights up permanently. One of the following fault codes is stored in the ACSM (air bag control unit): 930949 - Knee airbag, driver: short circuit to negative terminal 93094F - Knee airbag, front passenger: short circuit to negative terminal.

ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.

CUSTOMER SUPPORT PROGRAM. FRONT DRIVER SIDE AIRBAG MODULES.

For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.

designates changes to this revision SUBJECT Airbag Warning Lamp Illuminated, FC 93EB or FC 55 . The red airbag warning lamp (AWL) in the instrument cluster is illuminated and a fault code for ""Emergency call function..."" is stored in the MRS5 (Multiple Restraint System) control module. The fault code is FC 93EB for the E90 and E91 or FC 55 for the X3. The fault occurs regardless of whether the vehicle has a TCU (Telematics Control Unit) or not. Internal varistor fault within the MRS control module."

Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata driver?s side airbag module in a listed vehicle.

THIS IS CAUSING THE BATTER TO NEED TO UNDERGO AN ENERGY DIAGNOSIS. *KB

WHERE IT IS NECESSARY TO REPLACE THE RIGHT OR THE LEFT SIDE FUEL LEVEL SENSOR DUE TO A FAILURE, THE ENTIRE PUMP AND HOUSING OR DELIVERY UNIT (SUCTION JET ASSEMBLY) DO NOT NEED TO BE REPLACED AS WELL. IN SOME CASES, EPC DOES NOT SHOW THAT THE REPAIR KIT IS AVAILABLE SEPARATELY IN THE ILLUSTRATION, BUT IT IS AVAILABLE IN THE PARTS DESCRIPTION. ALL MODELS. NO MODEL YEARS LISTED. *PE

CODING/PROGRAMMING OF THE DXC MODULE. DUE TO A SOFTWARE ERROR OF THE STEERING ANGLE SENSOR, THE DXC WARNING MAY BE DISPLAYED AFTER THE ADJUSTMENT IS PERFORMED. E83 (X3). *PE

A LOW VOLTAGE CONDITION CAUSED THE STEERING ANGLE SENSOR POSITION DATA TO BE LOST. THE BATTERY MAY HAVE BEEN DISCHARGED OR DISCONNECTED. (MODEL E83). *PE

MODEL E90, E91 (3 SERIES) AND E83 (X3) VEHICLES PRODUCED BETWEEN 8/31/05 AND 4/26/06. RED AIRBAG WARNING LAMP (AWL) IN THE INSTRUMENT CLUSTER IS ILLUMINATED AND A FAULT CODE FOR EMERGENCY CALL FUNCTION IS STORED IN THE MRS5 (MULTIPLE RESTRAINT SYSTEM CONTROL MODULE. *PE

heard.

This can occur to the drivers and/or the passengers front seat.

Wind noise 2. Excess water entry

Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

THIS CAUSES THE MANUAL AND AUTOMATIC EMERGENCY CALL AND ROADSIDE CALL (BMW ASSIST) NOT TO FUNCTION. MODELS E53, E60, E90, E83 ARE AFFECTED. *PE

This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via Voice over LTE (VoLTE) function. For this purpose the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.

Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

bulletin supersedes SI B01 31 18 dated October 2018.

bulletin supersedes SI B01 31 18 dated October 2018.

Ultimate Rewards platform to include a new Recall Support page. This page will allow IRFs to check their customers VINs for open Takata recalls; and get rewarded for helping us with completing repairs.

THE AIRBAG WARNING LAMP (AWL) IS ILLUMINATED, TOGETHER WITH THE PASSENGER AIRBAG STATUS LAMP (POL). THE PROBLEM MAY BE INTERMITTENT. MICROCRACKS IN THE OC3 SEAT MAT. *PE UPDATED 9/30/11. *PE

INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several ""mechanism sets"" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP. "

INFORMATION Sunroof Repair Instructions: The panoramic sunroof contains several ""mechanism sets"" which can be repaired and/or replaced independently in the event of a mechanical failure. When performing such a repair to any of these sets, the TIS/ISTA Repair Instructions (REP) should always be consulted. Due to the complex nature of these repairs, a set of complementary instructions with additional detail, explanation, and photos has been developed. The attached Repair Instructions should always be used in conjunction with the TIS/ISTA REP. Refer to the following repair attachments: Front Glass Mechanism repair E53, E61, E70, E83, E91.pdf Rear Glass Mechanism repair E53, E61, E70, E83, E91.pdf Wind Deflector Mechanism repair E53, E61, E70, E83, E91.pdf Sunshade Mechanism repair E53, E61, E83.pdf Sunshade Mechanism repair E70, E91.pdf All panoramic roofs for the above-listed models are conceptually similar and utilize similar repairs. NOTE: An E83 (X3) sunroof cassette is used for demonstration of the repairs. Some differences may exist between this and other models. The following prerequisite work is required in order to replace the following kits (in addition to removing the cassette from the car and glass from the cassette): Front Glass Mechanism - None. Rear Glass Mechanism - Remove the front glass mechanism. Wind Deflector Mechanism - Remove the front glass mechanism; remove the rear glass mechanism. Sun shades and Shade Mechanism - None Sunroof Mechanical 3D Animation: A 3D animation has been developed in order to clarify how the sunroof mechanism operates, as well as how it is assembled and disassembled. To view this animation, open Interactive Career Pathways (ICP) and select ""Replace Front and Rear Glass Panel Mechanic"" from the Technical Service Information section of the home page. This animation allows you to: * Operate the mechanism and view from any angle; * Add or remove parts and then cycle the sunroof; * S

irritating to the customer; or it is not possible to locate certain addresses, for instance:

irritating to the customer; or it is not possible to locate certain addresses, for instance:

BMW F25, AND F30 MODELS. *KB

*PE

DOFF DURING DRIVING AND THE CONTROL CHECK MESSAGE IS INDICATING DEFECTIVE DRIVING LIGHT OR PARKING LIGHT. *PE

*RM

MODEL E90, E91(3 SERIES);E92, E92 (3 SERIES); E60 (5 SERIES); E60 (M5); E63, E64 (6 SERIES); E63, E64 (M6); E65, E66 (7 SERIES); E70 (X5); E83 (X3); AND E85, E86 (Z4). *PE

TELEMATIC CONTROL MODULE,CAR ACCESS SYSTEM, RADIO/NAVIGATION, CENTRAL GATEWAY MODEL OR FOOTWELL MODULE) DURING VEHICLE TESTING, NO ENGAGEMENT OF TRANSMISSION GEARS, FAIL TO START, WHEN DRIVING, WILL STOP RUNNING. MODEL F25 (X3). *PE

THE TRANSMISSION WILL NOT UPSHIFT, USUALLY AFTER GOING UP A SLIGHT INCLINE, AND STAYS IN EITHER 3RD OR 4TH GEAR TOO LONG. CALIBRATON SENSITIVITY IN THE HILL RECOGNITION PROGRAM OF THE EGS TRANSMISSION MODULE. MODELS E83, X3. NO MODEL YEARS LISTED. *PE

between March 1, 2022 and March 8, 2022 because the torsion struts may not have been installed at the plant. Do not deliver to a customer, a New, Certified Pre-Owned or Used vehicle subject to a Delivery Stop, until the vehicle is repaired. Do not use or sell replacement equipment/parts subject to a Delivery Stop.

THE WARNING LAMPS FOR DSC, ABS AND BRAKE WARNING ILLUMINATED. THERE MAY ALSO BE A WARNING IN THE CONTROL DISPLAY FOR CHASSIS CONTROL SYSTEM FAILURE. *JS

INFORMATION REGARDING THE DEFECT IN THE REAR WINDOW DEFROSTER THAT FAILS TO OPERATE PROPERLY. NO MODEL YEARS LISTED. *PE

*RM

ONCE IT IS VERIFIED THAT WATER HAS INDEED ENTERED THE ELECTRONICS BOX, IT WILL BE NECESSARY TO REPLACE BOTH THE LOWER PART OF THE ELECTRONICS BOX AND THE LID OF THE ELECTRONICS BOX. *PE UPDATED 8/3/11. *PE