2020 BMW S 1000 XR TSBs
24 Technical Service Bulletins across 8 categories
Engine
9 bulletinsFront and rear wheel speed sensor faults (0x3A1800 and 0x3A1801) appear after the bike is being revvedover 5000 RPM...
Read full bulletin
while still on the side stand, sometimes in conjunction with the side stand fault 0X3A1331. When the engine is revved up while on the side stand, vibrations are sent through the entire motorcycle.This vibration intensity varies from bike to bike. This vibration can cause particular movement between the wheel speed sensor and the sensor ringsdepending on the position of the sensor to the ring. The movement is picked up as rotation speed and iscalled ghost speed. This ghost speed follows the increase in RPMs. 5000 RPM = approx. 12 MPH 10000 RPM = approx. 31 MPH
The engine wiring harness may chafe on the honeycomb structure of the frame.
Read full bulletin
In case of damage to the wiring harness, the wake-up line of the instrument cluster will be damaged.
BMW Motorrad USA is pleased to announce the launch of the BMW Motorrad Ultimate Care Program, effective June 23 , 2021.
Read full bulletin
Three different plans will be offered for consumer bikes, as well as two Authority-specific plans. Model-year 2020 and newer BMW Motorcycles from the time of retail up to the first scheduled ?break in? service are eligible.
Vibrations on the handlebars in an engine range from 2000 to 4000 rpm may be perceived as uncomfortable by some...
Read full bulletin
customers.
Warning light in the instrument cluster for DCC failure in motorcycles equipped with DCC
During a cold start or while idling in neutral after a brief standstill, the engine runs at higher revolutions, sounds...
Read full bulletin
irregular and as if there are misfires (i.e. as if it were only running on 3 cylinders).
Lurching at partial load range and Idle speed is unstable
SERVICE ACTION - ABS MODULATOR MOUNTING BOLT: During assembly, an additional mounting bolt was installed on the ABS...
Read full bulletin
pressure modulator instead of a plastic rivet. This changes the vibration behavior of the ABS modulator. When the motorcycle is frequently used at very high engine speeds, vibration damage to the components could occur.
The engine wiring harness may chafe on the honeycomb structure of the frame.
Read full bulletin
In case of damage to thewiring harness, the wake-up line of the instrument cluster will be damaged. The instrument cluster will nolonger be activated with "Ignition ON?.
Electrical
5 bulletinsThe electrical system of BMW vehicles has been subject to an ongoing development process over the last few years.
Read full bulletin
This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
BATTERY EMPTY DESPITE CHARGER.
Warning light and fault message in the TFT with faults stored for the rear oxygen sensor (after the catalytic converter).
Read full bulletin
The failure usually occurs shortly after the vehicle handover or the running-in check
It has been reported that the fuel hose comes loose at fuel distributor/pressure sensor.
Read full bulletin
Because of thios, there is fuel leak that occurs when switching on the ignition.
Battery connection terminal broken off
Other
4 bulletinsCHECK ROCKER ARMS AND REPLACE WHERE NEEDED.
Due to a process deviation during production, the surface coating of the rocker arms may wear prematurely.
When diagnosing fault codes (0x3A13D7, 0x3A13D9), technicians erroneously condemn the electronic throttle grip, which...
Read full bulletin
analyses show is rarely the culprit.
Grab handles have replaced luggage racks despite despite order requiring luggage rack.
Brakes
2 bulletinsDuring assembly, an additional mounting bolt was installed on the ABS pressure modulator instead of a plastic rivet.
After replacement of the ABS control unit, the malfunction indicator lamp in the instrument cluster lights up and the...
Read full bulletin
DME stores the following fault memory: 0x0027ED DME: No CAN message In addition, the changeover riding mode no longer works.
Lighting
1 bulletinAfter close inspection it has been found that DYNAMIC PRO riding mode cannot be selected with the MODE button, even...
Read full bulletin
though it was enabled in the main menu. It is also not possible to configure the DYNAMIC Pro riding mode.
Suspension
1 bulletinDepending on the chassis and suspension adjustment, as well as vehicle load, the drive chain may make contact with the...
Read full bulletin
swing arm under certain conditions.
Body & Paint
1 bulletinInner trim frame cracked.
Transmission
1 bulletinWhen the bike is propped on side stand and is revved up to > 5,000 rpm in neutral gear, the malfunction indicator lamp lights up.
Read full bulletin
(see attached video for an example of this)