2015 Bmw 535i TSBs

There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE

plaintiffs in the following class action: Isley, et al. v. Bayerische Motoren Werke Aktiengesellschaft and BMW of North America, LLC.

conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.

With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al

With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al

tightening torque for the High-Pressure pump M6 mounting bolts to the cylinder head cover. The correct tightening torque is only 12 Nm for the M6 bolts.

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

Check Engine Light (MIL) is illuminated and the following faults are stored in the digital motor electronics (DME): Fault code Control module Fault code text 191A94 DME Fuel tank non-return valve: clamped shut And/Or: 191A93 DME Fuel tank non-return valve: clamped open Software error.

Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on.

a consultation that the M Compound (standard equipment) and M Carbon Ceramic (optional) brakes are high-performance brake systems which are designed for sporty dynamic driving styles. As a side effect of the highest possible brake performance customers are likely to hear noises due to the extremely resilient materials.

In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.

One or more of the crankcase ventilation hoses are not FPM (fluoroelastomer) rubber material. The FPM rubber material is engine heat resistant. Or The plastic corrugated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.

The engine malfunction warning is illuminated and one of the following fault codes are stored in the DME shortly after programming the vehicle or with a customer complaint.

While engine oil consumption may create a customer inconvenience in the short term it should not cause any drivability problems that would prevent normal day-to-day operational use of the vehicle.

On the affected vehicles a DME software error prevents the Check Control Message (CCM) "Low Engine Oil Level" to be displayed in instrument cluster (Kombi) when the engine oil level drops below the minimum level.

vehicles consistent with all other N63x engine equipped vehicles.

vehicles consistent with all other N63x engine equipped vehicles.

replaces SI B11 14 17 dated February 2018.

One of the following complaints may be reported The engine runs erratically; The engine causes vibrations when running; Grinding noise from the engine compartment when engine is running.

The Selective Catalyst Reduction (SCR) control module can make an error when calculating the DEF line pressure. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.

INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump. If injectors need to be replaced, enter the VIN of the vehicle into the ETK and select the part numbers found on screen 13_1416: ""High-pressure rail/injector/mounting."" Always enter the VIN for the vehicle into ETK when searching for parts. When the ETK is corrected, this SIB will be updated. WARRANTY INFORMATION Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/224...5/4/2015"

The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

causing the Check Control message: ""Chassis function restricted. It is possible to continue driving. Have the system checked as soon as possible by your local BMW Service Workshop"" to be displayed."

The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.

The Engine ""Drivetrain Malfunction"" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or ""stop and go"" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures."

The Service Engine Soon light is on. There may also be: Complaints of lack of engine performance An exhaust smell coming from the engine area. The following fault codes may be stored in the DDE: 24CE00 - Hot film air mass meter: Ratio of measured to calculated air mass too high 27F000 - Charge air hose monitoring in idle: Charge air hose fallen down 290900 - Air system, air to EGR air mass flow plausibility: Measured air mass compared to calculated air mass too high 290A00 - Air system, air to EGR air mass flow plausibility: measured air mass compared to calculated air mass too high and high charging pressure control deviation 1. Excessive thermal load from the EGR system on the intake components 2. An excessive or unmetered air leak in the intake/charge air system

bulletin supersedes SI B11 17 15 dated August 2015.. INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.11 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."

Customer complains that engine oil is leaking from the center of the vehicle. When verified, the engine oil residue can be seen leaking from between the engine and the transmission bell housing.

After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).

The Engine Drivetrain Malfunction"" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or ""stop and go"" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures."

When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.

This Service Information bulletin supersedes SI B16 07 15 dated January 2016. designates changes to this revision SUBJECT Fuel Tank Non-Return Valve Faults with SES Light. Check Engine Light is illuminated and the following faults are stored in the DME: 0x191A94 - Fuel tank non-return valve: clamped shut 0x191A93 - Fuel tank non-return valve: clamped open CAUSE Software and hardware errors

dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.

SUBJECT N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. CAUSE When the vehicle is parked overnight the engine oil pressure will equalize and may leak past the turbo charger exhaust side turbine seal.

A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.

14 dated December 2014, designates changes to this revision. SUBJECT NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak . The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm. CAUSE: Contamination of the NVLD pressure switch diaphragm and/or the contamination of the NVLD dust filter.

The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.

Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.

??Oil leaking from the Rain/Light Sensor (RLS). Note: This oil serves as a separation medium between the RLS mounting gel pad and the windscreen. The oil ensures damage free disassembly in case of repair. CAUSE The oil that serves as the separation medium of the Rain/Light Sensor (RLS) gel pad and the windscreen leaks out. Expose the Rain/Light Sensor (RLS) and properly clean the area of all oily residue. Note: The separating oil usually leaks only once from the pad at the RLS. Due to the small oil quantity in the gel pad, additional oil leakage is not plausible. Leaking oil does not impair the function of the RLS.

the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.

Due to a software error, the plausibility check between the tank shut-off valve (TAV) and the internal pressure sensor does not work correctly.

After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.

This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: z 213901 - Power management: Reduction or shutdown of individual electrical consumer z 8040BD - Reset or deactivation of Terminal 30F z 8040B9 - De-activation of terminal 30B: Top start capability limit reached z 8020E8 - Reset or deactivation of terminal 30F z 800E89 - FRM: start capability limit reached with lights active during stationary mode z 93076B - Deactivation of terminal 30B: upper start capability limit reached z 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active z 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active z 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE z The check control message (ID 229) is caused by a heavily discharged battery. z The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). z In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. z Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. z The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting

Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.

The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting

The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

A customer may complain of a delay in engine response after decelerating at low road speeds and then reaccelerating. This can occur when the transmission remains in a high gear due to a delay in the transmission downshifting. This situation can be more noticeable while driving on roads with slight turns or with an increasing gradient. Unfavorable EGS and DME software

The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts

The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

The customer states that the engine malfunction warning lamp is illuminated and, while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Vehicles with option 610 (Head-Up Display) are not affected. Follow the ISTA/D test plan for the applicable faults stored in the DME. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling.

When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut

The center console lock cylinder is loose. Manufacturing tolerances of the center console lock cover cap may cause it to become loose or missing. AFFECTED VEHICLES This Service Action involves F01, F02, F06, F07, F12 and F13 vehicles produced from March 7, 2014 to April 23, 2014. First check if a Service Action label with a code number 688 is already attached to the B-pillar. If a code number 688 has been punched out, the Service Action has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.

During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs," etc. If this visual appearance of accumulated oil on the engine assembly as an "active leak" is misinterpreted, unnecessary gasket repairs/replacements will result. Specifically, our analysis of the claim-related data for vehicles equipped with the engines noted in this bulletin is showing an above-average number of engine gasket repair/replacement claim submissions. The purpose of this bulletin is to provide your workshop with information and a procedure that will help in identifying engine oils leaks that do and do not require a repair.

INFORMATION There is an error in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. The vehicle may also exhibit rough running at idle and while driving. F07 and F10: P/N 13 64 7 639 994 is for all vehicles produced from 7/2014 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2014 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 F06, F12 and F13: P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 Until further notice, it is good practice to verify that the injector part number being removed from the engine matches the new injector part number. Always review the vehicle history to identify if the injectors have already been replaced. When the ETK data is corrected, a notification will be distributed. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16028.3.B130413... 4/24/2014

Check Engine Light is illuminated and the following faults are stored in the DME: 0x191A94 - Fuel tank non-return valve: clamped shut 0x191A93 - Fuel tank non-return valve: clamped open CAUSE Software and hardware errors

The Service Engine Soon lamp and Engine Malfunction warning are illuminated, and the vehicle has reduced power output. This situation can occur as a customer complaint, or after performing repairs to the engine valve train assembly. One or more of the following faults is stored in the DME. F10, F25, F30, F31 and F34: 131401 VANOS, exhaust, starting from cold: Non-adjustable 131501 VANOS, intake, starting from cold: Non-adjustable 131808 VANOS, exhaust, starting from cold: Position not reached 131908 VANOS, intake, starting from cold: Position not reached 130104 VANOS, intake, control fault, camshaft jammed 130304 VANOS, exhaust, control fault, camshaft jammed 130308 VANOS, exhaust, control fault, position not reached 130108 VANOS, intake, control fault, position not reached E84 and E89: 2D54 VANOS, exhaust, starting from cold: Non-adjustable 2D55 VANOS, intake, starting from cold: Non-adjustable 2D56 VANOS, exhaust, starting from cold: Position not reached 2D57 VANOS, intake, starting from cold: Position not reached 2D60 VANOS, exhaust, control fault, camshaft jammed 2D5A VANOS, intake, control fault, camshaft jammed 2D5B VANOS, intake, control fault, position not reached 2D61 VANOS, exhaust, control fault, position not reached If one of the applicable faults listed above is not stored in the DME fault memory then continue troubleshooting with the applicable test plan for the fault(s) stored. CAUSE This is due to a diagnostic programming error in the DME.

There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).

Under certain cold starting conditions, the engine may shudder or run a bit erratically for the first few moments when starting off. This can be felt at an engine speed of approximately 1,500 rpm. No relevant faults are stored in the DME memory. DME software calibration

Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL) may be on with several poetential faults stored. The DME has malfunctioned due to an internal fault.

The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles. The following fault codes may be stored in the DME: E Seriesz 36AE - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 2DE2 - Valvetronic, actuation, voltage phase: Line disconnection z 2DE3 - Valvetronic, actuation, volt phase: Line disconnection z 2DE4 - Valvetronic, actuation, volt phase: Line disconnection F Seriesz 1F0905 - DME, internal fault, Valvetronic: Current implausible One or more of the following secondary faults may also be stored: z 135B10 - Valvetronic, actuation, voltage phase: Line disconnection z 135B11 - Valvetronic, actuation, volt phase: Line disconnection z 135B12 - Valvetronic, actuation, volt phase: Line disconnection Engine performance and driving characteristics are not affected. DME software diagnostic sensitivity.

The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.

The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement of the crankshaft position sensor 2. Replacement of the incremental sensor wheel on the crankshaft 3. Replacement of the crankshaft 4. Replacement of the crankcase (block) with pistons 5. Replacement of the engine assembly Due to slight tolerance differences with the new replacement hardware and the original learned crankshaft position, values could cause cylinder balance calculation errors by the DME. DME software (the incremental wheel adaptation cannot be cleared)

The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.

The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.

There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.

When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.

Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the front or rear of the hood)."

designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail."

The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

The high-voltage battery is cooled by refrigerant as part of the vehicle's AC system. It is regulated using an expansion valve at the base of the battery itself. This expansion valve can become stuck in the open position, either intermittently or permanently. Fault code 21F107 - Cooling valve: valve couldn't be closed will be stored in the SME. CAUSE 1. Excess material from the manufacturing process can become lodged in the valve, causing it to stick open. 2. The diagnostic software in the SME control unit is not robust enough and can lead to a fault being set when a particular threshold is reached, despite the fact that the valve is not actually sticking.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.

INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] Page 1 of 3 Page 1 of 1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015 Page 1 of 3 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/232...6/4/2015

The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output.

designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE ? The check control message (ID 229) is caused by a heavily discharged battery. ? The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). ? In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. ? Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. ? The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting down certain electrical consumers.

designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: z FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.

Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/248...9/3/2016 Page 2 of 2"

No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: o Battery discharge when engine off. o Caution, no acoustic warning signals. Non BMW approved (third-party supplier) USB cable plugged into the USB port.

Volume of audio system (when set to near maximum) is reduced when Auto Start-Stop (MSA) stop occurs and is not restored upon automatic engine restart. This is normal system behavior - serves to protect the head unit, battery drain and avoidance of incremental leaps in the loudness. The loudness is reduced to 2/3 of maximum and is not restored. Note: Air conditioning output is also reduced upon MSA stop and is not restored for similar reasons.

Check Engine Light is illuminated and the following faults are stored in the DME: 0x191A94 - Fuel tank non-return valve: clamped shut 0x191A93 - Fuel tank non-return valve: clamped open CAUSE Software and hardware errors.

July 2014 What's New: Model - Removed models which no longer support BMW Assist functionality and added new models. Procedure - Add step requesting print out of ConnectedDrive Service Cockpit page Information - Add SI for ConnectedDrive Service Cockpit; updated the hyperlinks and email address for CD support team; deleted scenario for old CDMA unit which are no longer supported. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

Pop noise coming from seat backrest when pressure exerted toward rear or while pulling away from a stop. Friction between top right rivet holding lordosis (back Lumbar support) valve block and backrest cushion spring.

injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.

Taillight flickers when turn signal and brake light are active; see video in this link: tinyurl.com/zmr65st When the following preconditions occur simultaneously: Engine on (idle). Tail light active (switched on). Brake light active (through actuation of the brake pedal). Turn signal active (switched on). Current fluctuations reduce the voltage to the tail light.

indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.

format updated ? Consequential Additional Repair(s) statement added ? Overlapping Labor Procedure statement added . The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.

Refer to the Warranty section for details. . The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.

. The Service Engine Soon lamp is illuminated. The following fault codes may be stored in the DDE: N47T/N57T engine 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 245800 - particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) M57Y engine 480A Particle filter system - filter is heavily contaminated. (exhaust backpressure is too high) 481A Particle filter system - filter is heavily contaminated. (exhaust backpressure is above maximum) CAUSE 1. Faults with the exhaust system that affect the monitoring of the DPF by the DDE 2. Unfavorable recent driving profile INFORMATIOM During normal driving, there is a continuous regeneration of the diesel particulate filter that takes place at exhaust-gas temperatures between 280 and 350C (slower oxidation process). The soot particles can only be burned off when the required exhaust-gas temperature has been reached. Under certain driving conditions (i.e., prolonged short trips or an exhaust system which never reaches soot burn-off temperatures), the DPF can become restricted. The DDE will initiate periodic regeneration automatically, at the latest after 600 miles. In vehicles making many short distance journeys, periodic regeneration takes place after only 250-500 miles. The Digital Diesel Electronics control unit evaluates the time for periodic regeneration from the following values: average distance driven average driving speed temperature in the diesel particulate filter values from the exhaust pressure sensor The DDE initiates the regeneration process by decreasing incoming air by the throttle valve, and one or two post injections are executed. This heats the exhaust-gas temperature to approx. 600 C . When the exhaust temp reaches this point: The soot is burned off with the residual oxygen. The

The following performance issues may be noticed by the customer: CC-Message ""Drive faulty"" Engine jerking or a lack of power over the whole engine speed range Malfunction indicator lamp (MIL) is illuminated The following fault codes may be stored in the DDE: N47T/N57T engine Main Faults: 245700 - Particle filter system: particulate filter highly loaded (Exhaust backpressure high) 258300 - Exhaust backpressure sensor, Signal: Signal too high Secondary Faults: 244C00 - Charging pressure control, control deviation: charging pressure too low/positive deviation 25DA00 - Exhaust gas difference pressure sensor particle filter, Signal: short circuit to plus pole M57Y engine Main Faults: 480A particle filter system 481A particle filter system Secondary Faults: 4530 charging pressure control, control deviation 429A charging pressure control low pressure stage, control deviation Clogged DPF."

Information bulletin supersedes SI B11 17 15 dated October 2016. . INFORMATION When removing and/or installing the engine upper oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the engine upper oil pan refer to the newly released Repair Instruction 11 13 010 ""Removing and installing/replacing upper oil sump"" in ISTA/D 3.55.2 or higher for the proper procedures. IMPORTANT: The new repair instructions will state one of the following before reinstalling the upper engine oil pan. ""All threads must be cleaned with screw tap"" Or ""Clean all threads with screw tap. Order number 81 43 0 402 559"" Or ""Clean all threads with a thread cutter"". The current repair instruction terminology will be modified to include this information."

This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.

fails.

with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.

Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.

The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.

This Service Information bulletin replaces SI B62 11 18 dated January 2019. Whats New: ? Warranty section - Programming information added. A small black spot remains on the Central Information Displays (CID) illuminated screen which does not go away after a key cycle or sleep mode.

INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!

There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.

Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).

While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software

SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.

SUBJECT Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed . Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Note: If Fault Code E1C440 ""Headunit Reset"" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H."

Some information displays in the Instrument Cluster (KOMBI) may intermittently go blank. This may include the tachometer and speedometer displays. There is a software error in the KOMBI.

Run diagnostics and if display is found to be damaged, replace Head-Up display.

Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H

The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.

The customer complains of a rattle noise in either the left or right front door only when the speakers are in use. The inside door lock rod is making contact with the inside panel when the speakers are in use at certain volume and frequency levels.

The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly.

This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this service action to be completed prior to customer delivery.

INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.

After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.

When replacing the HU-H, the road map database version that was in the defective HU-H must be installed in the new HU-H.

The navigation system is inoperative unless the map is enabled during the QC1 Pre-Delivery Check. INFORMATION New vehicles come equipped with a navigation road map that must be enabled via an enable code (FSC). This process is part of the QC1 Pre-Delivery Check performed with the ISID (ISTA Diagnosis). IMPORTANT: There is no programming involved!

INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code and labor operations provided in the KSD2.

The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H

The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 ""display backlighting and graphics PCB switched off"" stored. Kombi software."

The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error.

Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.

INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the ""Attachment"" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received. "

designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with the vehicle connected to the ISTA diagnosis system. Refer to SI B65 22 14. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20588.1.B652413....3/2/2015

INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick. Refer to Attachment. 3. When prompted, enter the 20-digit enabling code. 4. Start the NAV road map installation and follow the on-screen instructions. WARRANTY INFORMATION Not applicable. ATTACHMENTS View PDF attachment B651015_Attachment.

The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H

Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: ""Title cannot be reproduced"" ""Is being read"" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB."

NBT Navigation does not provide routes that include certain toll roads. CAUSE Roads that have toll lanes ""without a cash option"" where not utilized for routing in NBT map data versions: NEXT 2015-1 NEXT 2015-2 NEXT 2016-1 As an enhancement, the NEXT 2017-1 map release now provides information about toll lanes ""without cash option"". UPDATE Install new map data."

cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.

What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.

INFORMATION As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an "update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. The last received transmitter, before the entrance into underground car parking or a tunnel, is still received and will show station identification. This fixed interval update does not apply to Traffic Message Channel updates which remain active. This new equipment operation pattern may be noticed by the customer after replacement of their Head unit. All replacement Head units delivered since 01/2016 have the upgraded design. An immediate solution would be for the customer to select one of their stored favorite stations via the menu or favorites buttons. PARTS INFORMATION Parts exchange or a software update are not effective or approved for this situation. WARRANTY INFORMATION Not applicable."

While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software

irritating to the customer; or it is not possible to locate certain addresses, for instance:

irritating to the customer; or it is not possible to locate certain addresses, for instance:

Samsung S6 and the S6 Edge.

This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.

The following DSC fault codes for the wheel speed sensors are stored: 480712 and/or 480715 and/or 480718 and/or 48071B They cannot be cleared, even though the wheel speed sensors work correctly and no problem can be found with the wiring harness.

For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle Nitrogen Oxide (NOx) Sensor(s) to: 10 years/120,000 miles as determined by the vehicle original in-service date.

communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.

Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.

While driving, a Check Control Message (CCM) is displayed advising of the following: Front collision warning failed Pedestrian detection failed The following fault code is stored in the KAFAS (Camera-based Driver Assistance System): 0X800AC4 - Camera calibration failed The KAFAS camera is not properly mounted and secured to the mounting bracket on the windshield; And/ or: The mounting bracket glued to the windshield is not installed correctly. The pictures below show both incorrect and correct installation. This picture shows the KAFAS camera installed in the bracket. Notice the spacing highlighted by the ""green lines"""

Fluctations of fuel level (causing resistance changes in the level sensor) while vehicle is stationary, are interpreted as refueling. This causes active ECO PRO mode bonus range to reset. Error in instrument cluster application.

For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.

SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information display. The check control message (ID 229) is caused by a heavily discharged battery. The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit).

BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's (Integrated Circuit Card Identifier).

1. The low beam flashes briefly after the ignition is switched ON. This situation can be duplicated every time the vehicle is started. 2. One of the faults below is stored and currently present: 0xDA1411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC 0xD9D411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC Faulty LED main light module (LHM2)

A headlight malfunction CC message is displayed for one or more of the following lights: -Daytime driving light -Turn indicator -Dipped headlight -Main beam The following fault codes in the FRM are stored: -800FC8 LIN bus, headlight driver module (TMS), left: communication fault -E58522 No message (status, exterior lights, front electronics 1, left, 0x1E0), receiver FRM, transmitter TMSL Software error in TMS 3 (headlight driver module AHL); a software I-level lower than 14-07-503 will cause the above situation to occur.

or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Work time labor operation code 61 00 006 is not considered a Main labor operation; however, it does require an individual punch time and an explanation on the repair order and in the claim comments Vehicle Programming and Coding When ISTA/P automatically reprograms and codes all the vehicle's control modules that currently do not have the latest software, and if control module failures occur during this programming procedure: ? Please claim this consequential control module-related repair work under the defect code listed in this bulletin with the applicable KSD2/AIR labor operations. Other Repairs Control module failures that occurred prior to this programming procedure and/or additional work is performed as a result of performing the ISTA diagnostics and related test plans: ? When covered under an applicable limited warranty, claim the control module-related and/or other repair work using the applicable defect code and labor operations in KSD2/AIR.

Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID Affected Central Information Displays were manufactured from 02/01/2013 to 06/09/2014. The manufacturing date is included in the serial number printed on the parts label on the CID. IMPORTANT: The manufacturing date is written in the following way: dd mm yy Example: The manufacturing date of August 15, 2013 is printed on the label in the following way: 15 08 13

Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.

INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system. Note: This VIN-specific NAV enabling code is then also automatically stored in the Repair Kit in the Aftersales Assistance Portal (ASAP). The automated INITIAL NAV enabling code request and activation of the navigation system will take no longer than 1 minute. After finishing "Delete Transport Mode," the navigation system in the vehicle will be active without entering the 20-digit INITIAL NAV enabling code manually or in ISTA. If the navigation system is not active and asking for the enabling code, turn off the ignition and wait for the head unit to enter sleep mode (approx. 3 minutes). After that, turn on the ignition again. The head unit will start up and the navigation system is activated. If the INITIAL NAV enabling code for first-time activation of the navigation system is not requested or delivered automatically, it still can be ordered manually through the Parts department and activated in the vehicle through the iDrive controller, by entering the 20-digit enabling code manually.

If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software

The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module

Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.

* In very cold weather conditions (32F or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. Software error in TMS 3 (headlight driver module AHL, xenon headlight)"

According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."

INFORMATION Do not replace any parts. NOTE: First time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Check, with the vehicle connected to the diagnosis system ISTA. Refer to SI B65 30 09. Connect the vehicle to the diagnosis system ISTA and activate the navigation system. The code is entered when running the QC1 Pre-Delivery Check test module. Refer to SI B09 04 09. IMPORTANT: No programming is required. WARRANTY INFORMATION Not applicable since the first time activation of the navigation system is part of the QC1 process and cannot be claimed separately.

* In very cold weather conditions (32F or below) with the light switch in the automatic position, the CCM (Check Control Message) ""Adaptive headlight malfunction"" is displayed. * When the CC message is displayed, all the lights continue to function. * When switching the headlights to high beam and the headlight unit is cold, the mechanism inside the headlight is too stiff to move. CAUSE Software error in TMS 3 (Headlight driver module AHL xenon light)"

December 2015 Technical Service. This Service Information bulletin supersedes SI 26 01 15 dated November 2015. The wrong temperature sensor for the Natural Vacuum Leak Detection (NVLD) may have been installed.

INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Vehicle Programming and Encoding If a control module was working properly and it fails to program correctly or requires initialization, please claim this additional work with the applicable KSD2 labor operations under the defect code listed above. The diagnosis and repair of vehicles ""arriving"" with failed control modules or stored faults which will cause them to fail during programming cannot be claimed under the defect code listed in this bulletin. Other Repairs If other eligible and covered work is performed ""prior"" to programming and coding the vehicle, claim this work with the applicable defect code and labor operations listed in KSD2. "

designates changes to this revision SUBJECT Door Open Message Displayed, Even Though Door Is Closed. While driving, a CCM (Check Control Message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. The FRM (Footwell Module) sees an incorrect door lock status caused by voltage variations in the door locks.

INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. CAUSE The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."

designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

The Dynamic Stability Control (DSC) warning light comes on while driving. The following DSC fault codes for the wheel speed sensors are stored: ? 480712 and/or ? 480715 and/or ? 480718 and/or ? 48071B They cannot be cleared, even though the wheel speed sensors work correctly and no problem can be found with the wiring harness. Due to high outside temperatures and extremely low atmospheric humidity, an electrostatic discharge (ESD) can occur in the wheel well area. This can transfer to the wheel speed sensor, causing irreparable damage to the DSC control unit.

INFORMATION ON THE OPERATION OF THE SMART OPENER MODEL F07 (5 Series Gran Turismo) F10 (5 Series) F12 (6 Series Convertible) F13 (6 Series Coupe) F15 (X5) F16 (X6) F22 (2 Series Coupe) F23 ( 2 Series Convertible) F25 (X3) F26 (X4) F30 (3 Series Sedan) F31 (3 Series Wagon) F32 (4 Series Coupe) F33 (4 Series Convertible) F34 (3 Series Gran Turismo) F36 (4 Series Gran Coupe) F48 (X1) F80 (M3 Sedan) F82 (M4 Coupe) F83 (M4 Convertible) F85 (X5 M) F86 (X6 M) G12 (7 Series) I01 (i3 Series) Vehicles with option code SA-0322 (Comfort Access) without M-Sport trim INFORMATION The smart opener (Contactless tailgate) operates as described below: Ignition key must be within 3 feet behind the vehicle, clear from any interference like a smartphone The customer must be at least an arms-length behind the vehicle Kick your foot forwards & backwards under the vehicle in one quick movement The taillights flash confirming that the trunk will open The trunk then successfully opens For more information an instructional video can be viewed which demonstrates the operation. Thanks to BMW of Tenafly for providing the video. tinyurl.com/Autotrunk1 https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016 Page 2 of 2 WARRANTY INFORMATION Not applicable. [ Copyright (c)2016 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/358...9/3/2016

INFORMATION For the eligible vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."

According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Front passenger seat occupancy detection transmitting fault (moisture)"" is stored. The fault may or may not currently be present. The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."

Depending on the vehicles equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.

Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.

Information bulletin replaces SI B66 23 17 dated February 2018 CONTACTLESS TAILGATE (SMART OPENER) IS TOO SENSITIVE.

Automatic trunk does not open fully on first attempt when using any opening options. During the first unlock attempt, whether using: the inside trunk switch, remote key, Smart opener (foot swipe), the automatic trunk lid only opens part way as shown. HKL software and trunk latch adjustment issue.

When operating front power windows a chattering noise can be heard. Front window regulator is lacking lubrication

A groaning noise can be heard from one or both of the front door decorative trim pieces while on rough roads. CAUSE The chrome plating of the trim mounting pins rubs against the door panel creating a groaning noise.

Corrosion of the front door and rear edges is appearing in paint surface near window trim. Material contamination.

? Noise detected upon closing door ? Damage to one or both window frame trims (front and rear door). CAUSE Front window frame trim is offset toward ""B"" pillar (as shown). Replace one or both window frame trim panels, if damaged."

NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Lubricate Rear Door Seam Seals. Under certain circumstances, the rear door seam seal may stick to the front door. Customers may be dissatisfied by the additional effort required to open the door. AFFECTED VEHICLES This Service Action involves F10 models produced from October 28, 2014 to January 12, 2015. First check if a Service Action label with a code number 731 is already attached to the B-pillar. If a code number 731 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Insufficient lubrication of the seam seal"

Orange triangle warning indicator, on exterior mirror, sporadically appears when there is no vehicle in warning zone. Control unit software error.

Trunk/tailgate may open when vehicle is locked. Trunk/tailgate may open while the vehicle is in motion. Usually after stopping, such as a traffic light etc. Vehicle key trunk/tailgate button may accidentally be pressed, thus opening the tailgate.

Wind noises/whistling noises from the front end of the vehicle or from the area of the front windshield. CAUSE Air passing through the gap between the front kidney grill and the body on LCI vehicles only. Install foam strips between kidney grills and body

Water on the inside (A) or misting (B) of both headlight lenses that is visible from outside. Water inside the headlights can be caused by two situations: Water/moisture ingress into the headlight housing. Thermal conditions that result in the formation of condensation. Note: An important indication that the moisture issue is caused by ""condensation"" rather than a ""water leak"" into the headlight housing, there will be misting/condensation in ""both headlights."""

INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle.

brakes are high-performance brake systems which are designed for sporty, dynamic driving styles. As a side effect of the highest possible brake performance, customers are likely to hear noises due to the extremely resilient materials. In the same conversation, inform the customer that his/her braking performance can help ensure that the noises do not occur or disappear quickly.

brakes are high-performance brake systems which are designed for sporty, dynamic driving styles. As a side effect of the highest possible brake performance, customers are likely to hear noises due to the extremely resilient materials In the same conversation, inform the customer that his/her braking performance can help ensure that the noises do not occur or disappear quickly.

Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.

brakes applied, noticeable at low speeds. The vehicle must be moving.

Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.

INFORMATION ""M"" vehicles are designed for high-performance, spirited driving. To accommodate this type of driving profile, a braking system which exceeds the standards for handling heavy brake forces, extreme temperatures, and excellent stopping power at high speeds is required. ""M"" vehicles can be ordered with the optional ultra high-performance braking system, featuring perforated carbon ceramic brake discs designed for circumstances similar to those encountered on racetracks. The carbon ceramic brakes were designed to improve braking efficiency, and dramatically increase braking performance along with a significant reduction in weight. When developing the carbon ceramic brake system, the main focus was on braking performance for the sporty-minded driver, while accepting the comfort limitations of functional noises at slower speeds and when coming to a stop. Please inform the customer that the carbon ceramic brake system's functional noises (squealing/honking), are a known characteristic for this type of material, and are only a small trade-off for the improved braking performance. These functional noises have no effect on the performance, operational reliability and durability of the brakes. Part replacement will not provide a remedy for the noise; this is a known characteristic of the high-performance brake system. More information on the performance and operation of these brakes can be found in the Owner's Manual under ""M carbon ceramic brake."" WARRANTY INFORMATION Not applicable."

Vibration while braking is noticed: ? Most commonly when coming to a stop from higher speeds ? Less prominent when brakes are cold. ? After wheel balancing, the problem still exists. ? All other diagnosis according to SI B34 10 16 have no results. Over time, the original style NAO brake pads can develop friction variations.

A squeaking noise can be heard when braking from a slow speed. This situation may apply to M5 and M6 vehicles fitted with the metallic brake pads (P/N 34 11 2 284 869). These pads can be identified by the absorber weights at the top and bottom. Due to the design of the fixed caliper brake system, an unfavorable interaction between components may cause a squeaking noise.

INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.

Wheel studs may loosen after wheels for the rear axle are incorrectly fitted to the front axle on vehicles equipped with option 2NK (ceramic brakes). Incorrect installation of rear axle winter tires (wheel style 409M) onto the front axle in conjunction with ceramic brakes

designates changes to this revision SUBJECT M5 and M6 Front Axle Brake Squeak with Compound Brake System. A squeaking noise can be heard when braking from a slow speed. This situation may apply to M5 and M6 vehicles fitted with the metallic brake pads (P/N 34 11 2 284 869). These pads can be identified by the absorber weights at the top and bottom. Due to the design of the fixed caliper brake system, an unfavorable interaction between components may cause a squeaking noise.

INFORMATION ""M"" vehicles are designed for high-performance, spirited driving. To accommodate this type of driving profile, a braking system which exceeds the standards for handling heavy brake forces, extreme temperatures, and excellent stopping power at high speeds is required. ""M"" vehicles can be ordered with the optional ultra high-performance braking system, featuring perforated carbon ceramic brake discs designed for circumstances similar to those encountered on racetracks. The carbon ceramic brakes were designed to improve braking efficiency, and dramatically increase braking performance along with a significant reduction in weight. When developing the carbon ceramic brake system, the main focus was on braking performance for the sporty-minded driver, while accepting the comfort limitations of functional noises at slower speeds and when coming to a stop. Please inform the customer that the carbon ceramic brake system's functional noises (squealing/honking), are a known characteristic for this type of material, and are only a small trade-off for the improved braking performance. These functional noises have no effect on the performance, operational reliability and durability of the brakes. Part replacement will not provide a remedy for the noise; this is a known characteristic of the high-performance brake system. More information on the performance and operation of these brakes can be found in the Owner's Manual under ""M carbon ceramic brake."" WARRANTY INFORMATION Not applicable."

Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.

When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.

Injectors to 10 years/120,000 miles as determined by the vehicle's original in-service date.

INFORMATION WARRANTY INFORMATION Not applicable. This Service Information bulletin provides technical and repair procedure-related information.

Integrated Navigation voice guidance is not loud enough to be heard over loud music. Software error in the CHAMP2 Head Unit.

An incorrectly displayed AdBlue (Diesel Exhaust Fluid refill range) CCM is shown on the Central Information Display. Improper instrument cluster software

Highlights of R-1234yf Meets SAE J2888_201301 ""This SAE Standard covers fittings, couplers, and hoses intended for connecting service hoses from mobile air- conditioning Systems to service equipment such as charging, recovery and recycling equipment"" New tools and equipment are required. To service vehicles equipped with R-1234yf refer to SI B04 02 16. Air conditioning technician certification is required to work on system. Refer to your State Law. Unique low and high side fittings. Revised evaporator core as per SAE J2842. System will use about 5% more refrigerant than a comparable R134a system. System oil is a specific PAG oil. Refer to ISTA repair recommendation. Do not interchange components between systems using other refrigerants. Do not reuse Seals / O-ring material from another system. The system piping has internal heat exchangers (IHX or IWT) as introduced in the G12 (7 series). SAFETY INFORMATION Several precautions need to be observed when working on automotive air conditioning systems: Always wear eye protection and gloves while handling refrigerant or servicing air conditioning system. Avoid breathing R1234yf lubricant vapor or mist. Use only approved service equipment to discharge A/C systems. If refrigerant or compressor oil contacts the skin or eyes, large quantities of cool water should be used to flush the affected area. Never heat a refrigerant container with an open flame. Keep all refrigerant away from open flames. Under no circumstances should R1234yf service equipment or vehicle A/C systems be pressure tested or leak tested with air/R1234yf mixtures. NOTE: The use of compressed air (shop air) for leak detection in an R1234yf system can contaminate the system and/or refrigerant with moisture. Leak detection equipment that meets the SAE J2791 standard will work with R1234yf Never use fittings for an R12 or R134a system on an R1234yf system. Any difficulty in connecting service equipm

designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.

INFORMATION When a defective high-pressure fuel injector is identified with an index "02" designation, as shown in the illustration below, all 4 injectors must be replaced at the same time. This bulletin only applies to index "02" injectors. Index "01" and index "03" or higher are not affected. No immediate repair is required unless the BMW vehicle is currently experiencing this problem.

designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty spare parts processes for the HU-H. For the US market, all vehicles will come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, there will be no physical copy of the navigation system road map data media DVD set or USB stick placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement HU-H parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, HU-H NAVI Road Map North America NEXT, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the HU-H NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there it then can be installed onto the HU-H in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI NEXT Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the HU-H by inserting the DVDs one by one into the HU-H internal DVD

designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.

designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts processes for the CIC. For the US market, all vehicles come pre-loaded from the factory with the latest navigation system road map database version that was available at the time of vehicle production. Therefore, no physical copy of the navigation system road map data media DVD set or USB stick is placed in these vehicles at the Vehicle Distribution Center (VDC). NOTE: Additionally, all replacement CIC parts come with a pre-loaded version of the current available navigation system road map database installed. A set of DVD copies of the navigation system road map database, CIC NAVI Road Map North America PREMIUM, is shipped to all BMW centers through the automatic tool shipment program with each release of a navigation system road map database. IMPORTANT: Additional copies or earlier NAV road map database versions cannot be ordered individually! Therefore, please take special care to archive the CIC NAV road map DVD sets! The NAV road map data on the DVD set can also be installed into the Network Attached Storage (NAS). From there, it can then be installed onto the CIC in the vehicle, using the Integrated Service Technical Application for Programming (ISTA/P). For installation of the navigation system road map data media DVD set onto the Network Attached Storage (NAS), please contact your ISPI Next Administrator. In addition to this procedure, it is also possible to download the NAV road map data on the DVD set directly to the hard disc drive (HDD) integrated in the CIC by inserting the DVDs one by one into the CIC internal DVD drive. It will take approxim

The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon. The current fuel consumption can selected and monitored in the instrument cluster while driving (the ""fuel consumption, current"" option is set to active in the settings menu). No relevant fault will be stored in the DME memory. DME software; the fuel injection rate under these conditions is too close to the minimum calculated threshold."

Water is found in rear compartment. CAUSE Seal around fuel filler tube (located by red lines) is not effective. Replace cover pot (bowl).

axle, when cornering, maneuvering, parking or pulling away from a parking space.

mph.

ConnectedDrive features are partially or completely inoperative. Examples of some of these features are listed below: * BMW Assist Inoperative ? SOS call ? Roadside Assistance call * My BMW Remote App * BMW Online - Google local search * Concierge CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availabilty (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle.

A noise may be heard from the left or right front seat base when driving on rough roads. CAUSE The riveting of the seat control bracket to the metal seat base is too loose.

along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added "Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."

inoperative.

seat may restricted.

axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.

Intermittent steering assistance failure CAUSE The power supply of the EPS control unit.

A groaning noise can be heard when the steering column is retracted and moves into the lower position. Friction between gap trim and the lower trim cover.

A groaning noise can be heard when the steering column is retracted and moves into the lower position. CAUSE Friction between gap trim and the lower trim cover

The screw connection on the power steering pump belt pulley may slacken. This may lead to an audible squeaking and rattling at the pulley drive. AFFECTED VEHICLES This Service Action involves 5 Series 535d vehicles according to VIN selection. First check if a Service Action label with a code number 682 is already attached to the B-pillar. If a code number 682 has been punched out, the Campaign has already been performed and no further action is necessary. Vehicles which require this Service Action to be completed will show it as "Open" when checked either in the "Service Menu" of DCSnet (Dealer Communication System) or with the Key Reader.

While driving at highway speeds, on older (worn) road surfaces, a buzzing noise is heard coming from the steering wheel. The Lane Departure Warning (LDW) vibration system

While driving at highway speeds, on uneven road surfaces, a buzzing noise is heard coming from the steering wheel. The Lane Departure Warning (LDW) vibration system

from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.

Torsional stress can cause the threaded fabric of the left air spring bellow to rupture and lose its airtightness. If the air spring is not airtight, the vehicle will lean on one side.

Torsional stress can cause the threaded fabric of the left air spring bellow to rupture and lose its airtightness. If the air spring is not airtight, the vehicle will lean on one side.

Torsional stress can cause the threaded fabric of the left air spring bellow to rupture and lose its airtightness. If the air spring is not airtight, the vehicle will lean on one side.

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

During inspection, the rear differential mount in the rear axle support shows signs of cracking.

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery. In the event the customer has already taken delivery of the vehicle, please perform the procedure the next time the vehicle is in the shop. This Service Information bulletin supersedes SI 11 11 15 dated January 2016.

ConnectedDrive features are partially or completely inoperative. * No traffic information (RTTI / ARTTI) * BMW ASSIST ""My Info"" service doesn't work. CAUSE The Electronic Subscriber Agreement (ESA) is inactive. * No active contract for ConnectedDrive features Offboard Availability (Backend) system issues * The external network was/is inoperative. * No data is sent to the vehicle."

BMW Online/BMW ConnectedDrive not functional. Vehicle and service cockpit have different ICC-ID's.

The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.

Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants

When the vehicle is in transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle is in transport mode, to reduce power consumption, the software is designed to disable the outside antenna receiver from waking up the vehicle.

The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.

When the customer presses or turns the controller, there is no or a delayed response. This can sporadically occur. Software in the controller

There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.

Note: No fault code is stored Software error in the Instrument Cluster

1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.

bags.

The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)

After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.

Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.

The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)

After programming the vehicle with ISTA/P 2.49.x or higher, the headlight and the horn can no longer be controlled using the My BMW Remote App from an iPhone. I-Level F001-13-03-501 or F010-13-03-501 and higher Note: The lock and unlock function via the App works as designed. CAUSE A software error in the central gateway (ZGW) control unit

When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.

Premature condenser failure due to corrosion. Replace the condenser if the vehicle contains the affected part number (9255983) AND the production date of the part falls on or before 11/11/13.

INFORMATION Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION