2025 BMW 530I TSBs

bottomphoto; drivers footwell shown ) , there is anoticeable lack of cable tension; and the hoodwill not unlock.

Over time, the seal gradually and increasinglydetaches which can cause it to- Dangle Become visible to the customer Prevent the door from closing properly

If the front left water drain hose is not connected, water can enter the footwell via the A-pillar and the carpet on the driver's side can soak up the water that has entered.

connected.

The groaning sound can be heard in the A-pillar/instrument panel area.

Overtime, the sealing material continues to detach more and more, which can cause the seal to dangle and become visible to the customer.

bottomphoto; drivers footwell shown ) , there is a noticeable lack of cable tension; and the hood will not unlock.

This situation may be worse in vehicles which are regularly waxed in th e area of the door jamb.

This can lead to the washer fluid reservoir being completely emptied.

completely lock afterclosing it.

pumps.

lean 034AA8 - Mixture control bank 1, lambda adaptation, mixture too rich And additionally with the faults above, these affected vehicles may have one or more of the followingirregular combustion-related faults also stored: 033812 033813 033814 033815 033816 033817 033818 033819

Driving with low to medium loads

TheCheck Control message Drive carefully. Driving stabilisation. will appear. In addition, the fault memoryentries below will be stored within 40 seconds of each other. ACSM: 02010A - Coding: Coding data not qualified VIP: 02390A - VIP control unit: Coding data not released, signature IB: 02290A - DSC control unit: Coding data not released, signature HKFM: 020D0A - HKFM: Coding data are not qualified

TheCheck Control message Drive carefully. Driving stabilisation. will appear. In addition, the fault memoryentries below will be stored within 40 seconds of each other. ACSM: 02010A - Coding: Coding data not qualified VIP: 02390A - VIP control unit: Coding data not released, signature IB: 02290A - DSC control unit: Coding data not released, signature HKFM: 020D0A - HKFM: Coding data are not qualified

to a premature battery failure. The 48 V battery may fail, triggering a corresponding Check Control message.

The head unit (HU-H5) is not responding in ISTA. Additionally, the Receiver Audio Module (RAM), Instrument Cluster (KOMBI) and Telematic Module 4 (TCB4) may not be responding in ISTA.

errors detected within PDC sensors. The warning indicates parking assistance featureshave limited functionality while the errors continue to be detected. Following faults may be stored 8031BA Ultrasonic Sensor Rear Side Left Software Error 8031CO Ultrasonic Sensor Rear outer left Software Error 8031AE Ultrasonic Sensor Rear Outer Right Software Error 8031A8 Ultrasonic Sensor Rear Side Right Software Error 8031B4 Ultrasonic Sensor Rear Middle Right Software Error 8031C6 Ultrasonic Sensor Rear Middle Left Software Error 8031CD Ultrasonic Sensor Voltage Supply Sensors Back: Short Circuit 8031CC Ultrasonic Sensor Voltage Supply Front: Short Circuit 8031CA Ultrasonic Sensors Front Extraneous Noise

automatic reconnection Display errors

Delayed start-up of the head unit (longer than 30 seconds) Failed start-up of the head unit Sporadic or permanent problems with navigation Sporadic or permanent Bluetooth connection problems Sporadic or permanent audio problems Sporadic or permanent speech / IPA (international phonetic alphabet) problems Missing displays, radio stations, camera images or applications

Thebacklight of the CID is illuminated, and touch function does register an audible sound.

(HU-H5).

Thebacklight of the CID is illuminated, and touch function does register an audible sound.

This flickering is not continuous but may occur once every 15 to 50 seconds. No fault memory entry is stored for this customer complaint.

(HUD) will revert to the Standard View. This is most noticeable when the Head-Up Display (HUD) deactivates for automatic mandatory reasons, such as rear camera activation or emergency call activation.

light on the door panel speakers will only illuminate in white.

happen that stored fault memory codes (DTCs) and the MIL (warning light) are not automaticallydeleted even though the underlying malfunction has already been rectified. This does not comply with the statutory OBD specifications.

happen that stored fault memory codes (DTCs) and the MIL (warning light) are not automaticallydeleted even though the underlying malfunction has already been rectified. This does not comply with the statutory OBD specifications.

The personalized color of the ambient lighting resets after the vehicle has gone to sleep.

Driving with low to medium loads There are no warning lights or Check Control messages.

removal and installation of the filters housing cover; the following air flap and/or air temperaturesensor faults are stored in the BCP: 80114D - Stepper motor: Unexpected error in Driving Cycle 801168 - Temperature sensor ventilation left or ventilation: short to ground 80116A - Temperature sensor ventilation right: short to ground 80116B - Temperature sensor ventilation right: short to plus or open circuit 80116C - Temperature sensor footwell left or footwell: short to ground 80116D - Temperature sensor footwell left or footwell: short to plus or open circuit 80116E - Temperature sensor footwell right: short to ground 80116F - Temperature sensor footwell right: short to plus or open circuit 80435B - Stepper motors: short-circuit by mass

80114D - Stepper motor: Unexpected error in Driving Cycle 801168 - Temperature sensor ventilation left or ventilation: short to ground 80116A - Temperature sensor ventilation right: short to ground 80116B - Temperature sensor ventilation right: short to plus or open circuit 80116C - Temperature sensor footwell left or footwell: short to ground 80116D - Temperature sensor footwell left or footwell: short to plus or open circuit 80116E - Temperature sensor footwell right: short to ground 80116F - Temperature sensor footwell right: short to plus or open circuit 80435B - Stepper motors: short-circuit by mass To prevent harness damage the wiring harness will receive a new retention strap the next time the vehicle comes to the shop for its cabin air filter service.

Concern may be intermittent. The following fault codes are stored in the FZD (Roof Centre Function) control module during a vehicle test: 0302A0- ESH (electrical sunshade): No standardization system 03029C- ESH (electrical sunshade): No init because boundary conditions not valid (motordiver)

80114D - Stepper motor: Unexpected error in Driving Cycle 801168 - Temperature sensor ventilation left or ventilation: short to ground 80116A - Temperature sensor ventilation right: short to ground 80116B - Temperature sensor ventilation right: short to plus or open circuit 80116C - Temperature sensor footwell left or footwell: short to ground 80116D - Temperature sensor footwell left or footwell: short to plus or open circuit 80116E - Temperature sensor footwell right: short to ground 80116F - Temperature sensor footwell right: short to plus or open circuit 80435B - Stepper motors: short-circuit by mass

80114D - Stepper motor: Unexpected error in Driving Cycle 801168 - Temperature sensor ventilation left or ventilation: short to ground 80116A - Temperature sensor ventilation right: short to ground 80116B - Temperature sensor ventilation right: short to plus or open circuit 80116C - Temperature sensor footwell left or footwell: short to ground 80116D - Temperature sensor footwell left or footwell: short to plus or open circuit 80116E - Temperature sensor footwell right: short to ground 80116F - Temperature sensor footwell right: short to plus or open circuit 80435B - Stepper motors: short-circuit by mass

See attached video V3202 26 EPS noise.

following CCM may be displayed: CCM-2525: Brake system. Drive at moderate speed

When this sleep error is present, a remote software upgrade(RSU) may be aborted and the FZD can become degraded. The following Check Control Messages (CCMs) may be displayed: Energy Management Increased Energy Consumption While Parked. Software Upgrade Failed Workshop Visit Required.

that were produced between January 14, 2022, and September 16, 2025.

route, at anytemperature, even in a slightly reclinedposition.

route, at any temperature, even in a slightly reclined position.

button, or an airbag deployment event. In some cases, the customer may not even be inside the vehicle.

Check Control message Parking brake failed. When parking, secure the vehicle against rolling away. Mustbe checked by the Service Partner. The vehicle is still held by the unaffected side and the transmission lock.

Check Control message Parking brake failed. When parking, secure the vehicle against rolling away. Mustbe checked by the Service Partner. The vehicle is still held by the unaffected side and the transmission lock.

The function must be activated again by the driver at the beginning of every trip. After asoftware update to 25-03-500 and higher, this occurs more frequently.

The permanent storage offault memories does not comply with the legal specifications of the authority (California Air Resources Board CARB). The fault has no effect on the use of the vehicle by the customer.

No seat memory. The heated seats settings in the menu are missing/different than in their previous BMW vehicle. They canno longer select, under the climate rules, at what temperature Fahrenheit the heated seats willautomatically turn on. Certain other apps and functions are not available The drivers seat moves to an unknown memory position