2017 BMW 335I TSBs

position without any customer influence.

This would lead to loss of coolant from the engine.

This would lead to loss of coolant from the engine.

to remove or breaks apart in the oil filter housing.

A. For the B58 engines, a BMW Oil Catch special tool for use in conjunction with removing the engine oilfilter insert is now available.

A. For the B58 engines, a BMW Oil Catch special tool for use in conjunction with removing the engine oilfilter insert is now available.

position.

not charge the vehicle.

steering wheel and/or there is limited power steering assist when maneuvering or parking the vehicle. For the basic steering gears, one possible cause is that the mounting bolts for the electric motor may become loose, missing and/or broken due to corrosion.

// Battery. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this will cause the CCM 415 to be displayed when starting the vehicle. Replacing the Controller in this case will not correct this situation.

more of the following faults are stored in the DME. All models: FC 191C02 - Fuel tank ventilation system 2nd discharge point: malfunction FC 195014 - Differential pressure sensor tank vent valve signal: fixed FC 118001 - Mixture control: mixture too lean FC 118401 - Mixture control: mixture too lean large deviation I01 only: FC 124103 - Mixture control: mixture too lean FC 124101 - Mixture control: Mixture lean large deviation CAUSE Internal mechanical defect in the tank ventilation valve. The defect can also result in a very loud clicking noise when the valve is cycling.

service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing.

the steering wheel and/or there is limited power steering assist when maneuvering or parking the vehicle. For the basic steering gears one possible cause is that the mounting bolts for the electric motor may become loose missing and/or broken due to corrosion.

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

The vehicle will run rough or hesitate when accelerating from a stationary position.

The Service Engine Soon light is on. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission oil heat exchanger or a faulty engine characteristic map thermostat.

On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing (1).

The engine will not start at temperatures below freezing. The starter does not turn and engage.

MILEAGE.

Correction software level updated Procedure text changes made due to an ISTA/D test plan name change Adjusted text in the Warranty section for use with AIR and the ISTA/D test plan name change. The vehicle will run rough or hesitate when accelerating from a stationary position.

In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.

The engine malfunction warning is illuminated and one of the following fault codes are stored in the DME shortly after programming the vehicle or with a customer complaint.

While driving slowly with low RPM or while idling a faint knocking or fluttering noise can be heard from inside the fuel tank. The customer may describe this noise as a "helicopter" noise from the rear of the vehicle.

A Delivery Stop has been issued (effective May 16 2019) on certain Model Year 2016-2020 BMW vehicles that have been produced between June 19 2015 and April 17 2019. A software error within the Digital Motor Electronics (DME) may cause a miscalculation of an onboard diagnostic (OBD) function. All vehicles will need a software update (no parts required).

The Service Engine Soon (MIL) light is on with the following fault stored in the Digital Motor Electronics (DME). In the situation being described the fault is primarily stored during the cold winter months along with the use of winter fuel.

One of the following complaints may be reported The engine runs erratically; The engine causes vibrations when running; Grinding noise from the engine compartment when engine is running.

In the DME control unit software.

Reduction of steering assistance after starting the engine. The DSC and steering warning lamp are illuminated in the instrument cluster. Check Control messages displayed: ""Driving stabilization. Drive carefully"" ""Increased steering effort required. Drive at moderate speed"". Control unit fault code entries: EPS: None ICM_25: 0xD01C0C - message fault (actual rack force, ID: AVL_FORC_GRD) - Timeout 0xD01B26 - message fault (actual EPS position, ID: AVL_PO_EPS) - Timeout 0xD019BF - message fault (actual driver actuator steering torque, ID: AVL_STMOM_DV_ACT) - Timeout 0xD016A5 - message fault (driving dynamics 02 check control display, ID: DISP_CC_DRDY_02) - Timeout 0xD015C4 - message fault (front axle electrical steering status, ID: ST_EST) - Timeout DSC_25: 0xD354EE - signal fault (actual front axle steering angle, ID: AVL_STEA_FTAX) - invalid No damage or other noticeable effects in the power supply and FlexRay EPS (electric power steering / electromechanical power steering): Flexray Transceiver switches itself off"

This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.

For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle Nitrogen Oxide (NOx) Sensor(s) to: 10 years/120,000 miles as determined by the vehicle original in-service date.

This bulletin is notice of a limited emission warranty extension. This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter Even though this is NOT a Recall, BMW NA is sending VIN-specific customer notification letters. The plastic fuel tank has two openings, one at the top right and the other at the top left. The top right opening (passenger's side, serviceable) provides a mounting point and repair access to the intake fuel pump/level sensor assembly. The top left opening (driver's side, non-serviceable) serves as an access point for the installation of the suction jet pump/level sensor assembly during the fuel tank manufacturing process. After these components are installed, the top left side opening is then permanently closed and sealed with the installation of a circular Coex biopolymer plastic cover plate which is welded into place. Over time, the left side opening plastic cover plate weld may become damaged. Should this occur, there is the possibility of fuel leakage. Additionally, your vehicle will store the corresponding fault codes that may also be generated, and the Malfunction Indicator Lamp (MIL) will illuminate.

and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.

communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.

be supported by the cellular network provider starting February 2022. The decision to phase out 3G network technology was made at the discretion of the respective cellular carriers and lies beyond the control of BMW. Due to the phase-out, BMW Assist and ConnectedDrive services will no longer be supported after this date.

Check as soon as possible" illuminates. Increased ground cable contact resistance at Electrical Machine Electronics (EME) due to corrosion/oxidation.

battery.

battery.

One or all the following may be experienced in the vehicle: An SOS malfunction is seen in the Kombi (aka instrument cluster) When pressing the E-Call/SOS button in the overhead console nothing happens Fault code B7F33C (internal ECU error) is stored in the Telematics control unit (ATM/TCB2) There are 2 known causes for this failure. They are as follows: Software file missing from the ATM/TCB2 control module Water leak at the "shark fin" roof antenna (aka roof aerial) leading to corrosion in the ATM/TCB2 control module.

illuminated even though the washer fluid reservoir is full. There are no faults stored in the system for the washer fluid level switch. A non-approved washer fluid was used that is silicone-based. Silicone-based fluids are not compatible with the contactless capacitive level sensor. Fluids that contain a silicone additive are normally colored other than blue.

Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.

Customer may complain of reduced air flow when the air conditioning system is operated for an extended time usually longer than 30 minutes. The evaporator starts to freeze up due to the position of the evaporator temperature sensor.

The windshield wipers switch on by themselves and can no longer be switched off despite activation of the switch. An internal software error in the SZL (steering column switch cluster).

INFORMATION The ST1821 High Voltage Diagnostic Specialist Certification (HVS) is the next step in the E-mobility service strategy for BMW technicians.

2019.

2019.

The customer's vehicle does not start due to a totally discharged battery.

Over time the mounting clips may fail allowing the center underbody panel to become loose. The mounting clips were not sufficiently hardened during production.

The low washer fluid warning light is illuminated even though the washer fluid tank is full. There are no faults stored in the system for the washer fluid level switch. CAUSE A non-approved washer fluid is used (fluids that contain a silicone additive, normally colored other than blue). INFORMATION The washer fluid level sensor is a contactless capacitive sensor. The sensor sends a low fluid level signal to the gateway module (FEM - Front Electronics Module or BDC - Body Domain Controller) which in turn displays a low washer fluid warning in the instrument cluster. The use of a ""non-approved"" washer fluid (silicone-based fluid) can cause the low fluid warning light to come on even when the reservoir is full. Refer to ISTA document ""FB-GZ-B17A-F20 Washer fluid level sensor"" for information on how this capacitive sensor operates."

After the transport mode is deleted (during the QC1), a BMW Assist (SOS) test call is made by pressing the SOS/ E-Call button. However, the call only connects via voice (no data is transmitted). The operator indicates that a crash call has been sent. ATM fault code ""B7F348 - Provisioning without signature OTA"" is stored. The provisioning of the ATM (Advanced Telematics Module) has failed."

This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC

illuminated when the Washer Fluid Tank is Full.There are no faults stored in the system for the washer fluid level switch.

During assembly oil may have contaminated the plastic housing of the rear tail lamps causing damage to the mounting points of the tail light assembly.

supersedes SI B61 23 15 dated April 2016.

The tail light mounting brackets may be cracked or broken. During assembly oil may have contaminated the plastic housing of the rear tail lamps causing damage to the mounting points of the tail light assembly.

supersedes SI B61 23 15 dated April 2016.

The tail light mounting brackets may be cracked or broken. During assembly oil may have contaminated the plastic housing of the rear tail lamps causing damage to the mounting points of the tail light assembly.

The tail light mounting brackets may be cracked or broken. During assembly oil may have contaminated the plastic housing of the rear tail lamps causing damage to the mounting points of the tail light assembly.

The tail light mounting brackets may be cracked or broken. During assembly; oil may have contaminated the plastic housing of the rear tail lamps; causing damage to the mounting points of the tail light assembly.

The upholstery may dislodge slightly from the thigh support base over time from repeated compression due to normal use.

fails.

with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.

Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.

The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.

changes between selections ("ghost behavior") and sounds an audio tone without the CID Screen being touched. The audio tone is the same one that sounds when you touch the CID with your finger to make a 'touch' selection.

During an active call the call audio autonomously switches from the vehicle hands-free system to the phone.

During an active phone call the call audio autonomously switches from the vehicle hands-free system to the phone.

The Central Information Display (CID) changes between selections (ghost behavior) and sounds an audio tone without the CID Screen being touched.

Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.

A groaning noise can be heard from the front door(s) when opening or closing the power windows.

Information bulletin replaces SI B66 23 17 dated February 2018 CONTACTLESS TAILGATE (SMART OPENER) IS TOO SENSITIVE.

Part Number Description Quantity F30; F31; F80 Front 51 33 7 414 531 Window guide; front left As needed 51 33 7 414 532 Window guide; front right As needed F30; F80 Rear A groaning noise is heard from any of the doors when driving over rough road surfaces.

Injectors to 10 years/120,000 miles as determined by the vehicle's original in-service date.

This component-specific limited emission warranty extension applies to defects in materials or workmanship.

system is operated for an extended time, usually longer than 30 minutes. The evaporator starts to freeze up.

system is operated for an extended time, usually longer than 30 minutes. The evaporator starts to freeze up.

Warranty Labor Operations changed. There is a rattling noise from the rear exhaust flap during initial start-up. The rattle could last up to sixty seconds.

the steering wheel.

the steering wheel.

steering.

This is caused by driving over obstacles (e.g. potholes) or an impact severe enough for the front spring strut damper to slip through the clamp of the steering knuckle.

brakes applied, noticeable at low speeds. The vehicle must be moving.

Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.

loosen/detach at the mounting tabs this can cause a clacking sound in the rear of the vehicle while driving. The plastic mounting tabs for the rear tail light assembly housing(s) may become too brittle and crack to the point where the hold down nut(s) can no longer keep the housing(s) in place.

The customer states that one or more of the following CC messages are displayed: 627 - Steering behavior: Drive moderately 070 - Steering: Drive moderately 765 - Rear-end collision restricted 850 - Pedestrian warning restricted 236 - Driving stabilization: Drive moderately 299 - SOS call system failure 042 - Brake system: Drive moderately After performing a vehicle test, one or more of the following fault codes are stored: ACSM - C9549A Message faulty (seat memory), ACSM receiver, driver's seat module transmitter FEM - D91DE0 No message, receiver FEM, transmitter TMSL FEM - D91EE5 No message, receiver FEM, passenger seat module transmitter ACSM - C9540C Message missing, receiver ACSM, transmitter FEM TMSL - D95402 Message missing, receiver TMSL, transmitter FEM KOMBI - E11454 No message, receiver KOMBI, transmitter REM FEM - D91DE6 No message, receiver FEM, transmitter TMSL TMSR - D99401 Message missing, receiver TMSR, transmitter FEM TMSR - D99402 Message missing, receiver TMSR, transmitter FEM FEM - 8041BA AHL system faulty FEM - D916C3 No message, receiver FEM, transmitter TCB ZBE - E2D403 No message, receiver CON, transmitter FEM-ZGM TRSVC - CA9428 Message incorrect, receiver TRSVC, transmitter PDC-REM TMSL- D95401 Message missing, receiver TMSR, transmitter FEM HU-H - S0397 MOST configuration was not stored TCB - E1445F KCAN2 or KCAN4: Line fault/electrical fault FEM - 8041B6 LWR faulty REM - E58468 Body CAN2; communication fault TRSVC - CA9427 Message incorrect, receiver all around vision camera, transmitter PDC/REM FEM - D91CEC Message missing, receiver FEM, transmitter REM Shorted K-CAN wiring under driver or passenger seat Shorted K-CAN2 wires were shorted between the left side trunk trim panel and the body of the vehicle Shorted K-CAN in left rear wheel well area Shorted K-CAN under center console trim Shorted K-CAN under A-Pillar trim

Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC73 must appear in the text of your TEC claim.

Screws attaching the power pack to the steering gear may be broken. Broken screws result in noises during steering motions and variable steering assistance. A Check Control Message (CCM) may be displayed.

Stiff movement in the steering or sticks when steering from one limit position to the other Unfavorable software of the Electric Power Steering (EPS)

Screws attaching the power pack to the steering gear may be broken. Broken screws result in noises during steering motions and variable steering assistance. Check Control Message (CCM) may be displayed.

This means that only the 4G network will be available. In the 4G network, voice calls will be transferred via the Voice over LTE (VoLTE) function. For this purpose, the SIM card must perform an IMS registration in the mobile communication network. Due to a production error, the telematics control units were delivered without an IMS configuration. The Connected Drive voice services (Concierge Call, BMW Assistance, and emergency call voice) can no longer be used regionally in the US in vehicle with telematics control units ATM-1 and TCB-4G. Voice control of the vehicle and all other telephone (paired mobile devices) functions are not affected. Emergency call location data is unaffected.

This Service Information bulletin replaces SI B84 02 14 dated September 2018.

18 dated November 2018.

longer than 30 minutes.