2013 Bmw 1 Series M TSBs

plaintiffs in the following class action: Isley, et al. v. Bayerische Motoren Werke Aktiengesellschaft and BMW of North America, LLC. The Settlement Benefits are effective and available on and after February 9, 2022. Note: This bulletin is a notice of a Class Action Settlement Service Campaign benefits that are now available.

USspecification

conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.

problems that would prevent normal day-to-day operational use of the vehicle

applies to: Class vehicles in operation on the road (Applicable N63 engine model vehicles); by Class members (Class Vehicle owners on the date this settlement became effective), And it provides diagnostic/repairs instructions, as well as, Warranty Information for performed remedies.

illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.

Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on.

What's New: The short-term extension window of one (1) year/12,000 miles from date of the settlement has expired.

What's New: Engine Timing Chain Guide Pre-Inspection (with Valve Stem Seal Repair) instruction added Updated N63 Replacement Engine Assembly/Part statement added Warranty Information section updated, including the current coverage and attachments.

problems that would prevent normal day-to-day operational use of the vehicle.

While engine oil consumption may create a customer inconvenience in the short term it should not cause any drivability problems that would prevent normal day-to-day operational use of the vehicle.

On the affected vehicles a DME software error prevents the Check Control Message (CCM) "Low Engine Oil Level" to be displayed in instrument cluster (Kombi) when the engine oil level drops below the minimum level.

Drivetrain Malfunction Warning is illuminated and DME fault code 1C4002 (Engine oil level: too low) is stored. Customer complains that Check Control Message (Low Oil level") has never been displayed. The engine oil level measurement test works correctly and shows low oil level when checked under Vehicle Status tab in CID. Instrument cluster software error.

Drivetrain Malfunction Warning is illuminated and DME fault code 1C4002 (Engine oil level: too low) is stored. Customer complains that Check Control Message (Low Oil level") has never been displayed. The engine oil level measurement test works correctly and shows low oil level when checked under Vehicle Status tab in CID. Instrument cluster software error.

INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced up to 7/2013

CAUSE The cause is related to, but not limited to, one or more of the following components and systems shown below: * Turbocharger * Crankcase ventilation * Engine gasket leaks * Internal engine tolerances and sealing * Improper filling or topping up Use the troubleshooting procedure below to help identify the cause."

Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) Note: Due to ongoing quality control monitoring, testing of the Bosch fuel system low-pressure sensor showed that replacement of the fuel system low-pressure sensor with Index 1 is no longer required in this customer care package. Refer to the attached procedure for the applicable replacement instructions regarding the fuel system low-pressure sensor. This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The N63CCP is NOT a mandatory Technical Campaign or Recall (per the authorities). It should only be completed based on parts availability, workshop capacity, and the customer's schedule. Complete all other applicable open Campaigns per the DCS Warranty inquiry and the Key Reader. Perform all recommended, due or qualifying ""time-based"" maintenance service task items as directed by the Key Reader/ISPA Light application. When eligible, also perform the procedure described in SI B61 30 14: 12-Volt Battery Replacement together with performing the N63 Customer Care Package. After completing all the necessary repairs, the vehicle needs to be road tested for 30 minutes to assure the highest standard of performed repairs (Please see ""Warranty Inf

For the eligible vehicles, BMW of North America, LLC (?BMW NA?) is extending the limited warranty for the engine Crankcase Ventilation Lines to: 10 years/120,000 miles as determined by the vehicle?s original in-service date Note: This bulletin is notice of a ?limited warranty extension.? This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter Even though this is NOT a Recall, BMW NA sent VIN-specific customer notification letters in a phased release.

INFORMATION When removing and/or installing the N63 or S63 engine ""upper"" oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the upper oil pan bolts as per Repair Instruction 11 13 010 ""Removing and installing /replacing upper oil sump (N63),"" the steps outlined in the attachment of this bulletin must be followed. Refer to attached document and the instruction section that applies to the procedure being carried out. The ISTA/D repair instructions are currently being revised."

Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil

After engine start-up, a CCM (Check Control Message) for SOS malfunction is displayed in the Kombi and in the CID (Central Information Display). One or more of the fault codes below may be stored in the TCB or Combox control unit: 0xB7F32B - GSM Antenna: Open Circuit 0xB7F31F - GSM Antenna: Short to ground 0xB7F31E - GSM Antenna: Open Circuit A signal error is identified during the aerial self-test performed by the TCB (Telematic Control Box or the Combox).

SUBJECT N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil

SUBJECT N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil

INFORMATION When diagnosing the low-pressure fuel supply sensor with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar at all times. * B1214_DI6KNDR * D18KHDR * AT1214_DIKNDR * AT1214_DIKHDR Do not replace the low-pressure fuel supply sensor. The operating pressure of the low-pressure fuel supply sensor can found in ""DME Diagnostic Query"" using the following procedure: 1. Exit the test plan and return to the control unit tree. http://www.bmwtis.net/tiscode/cgi-bin/omcgi.exe?sie_path=/tsb/bulletins/htm_store/14907...11/7/2012 Page 2 of 2 2. Select ""DME"" in the control unit tree. 3. Select "" Call Up ECU Functions."" 4. Select ""Diagnostic Query."" 5. Select ""Fuel Pressure (Low Pressure)."" 6. Select ""Query Status."" The engine must be running to verify operation of the pressure sensor. The software error will be corrected in ISTA/D 2.34, scheduled for release in December 2012. "

The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced from 1/2011 to 7/2013 P/N 13 53 7 568 607 is for all vehicles produced to 1/2011 It is good practice to verify that the part number being removed from the engine matches the new injector part number, until further notice. When the ETK data is corrected, a notification will be distributed.

The Check Control Message ""Drive, drive moderately"" is displayed with any of the following rail pressure sensor faults stored in the DME: 119001 - Rail pressure sensor, electrical: Short circuit to positive 119002 - Rail pressure sensor, electrical: Short circuit to ground 119101 - Rail pressure sensor 2, electrical: Short circuit to positive 119102 - Rail pressure sensor 2, electrical: Short circuit to ground A poor electrical connection between the rail pressure sensor and engine harness due to vibration"

INFORMATION With the release of ISTA/D 3.39.21, a new test plan is available for checking the engine oil level in some vehicles with the N63T engine. The test plan will help identify the actual oil level, and advise the amount that will need to be added to correctly fill the engine when topping up. When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: * F01 and F02 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F06, F07, F12 and F13 with the N63T engine, produced from 3/2013 and later with I-Level F001-13-03-501 or higher * F10 with the N63T engine produced from 7/2013 and later with I-Level F010-13-07-501 or higher Test plan path: Service Function/Drive/Motor Electronics/Motor Oil/Oil Level IMPORTANT: Do not perform this test plan on the following vehicles: * E70, E71, F01, F02, F04, F06, F07, F12 and F13 vehicles with the N63 or N63T engine, produced before 3/2013 l * F10 vehicles with the N63 engine produced before 7/2013 If this test plan is performed on these vehicles, the result is an incorrect measurement and level indication; overfilling of the engine will occur. Overfilling of the engine will result in engine damage. When a solution for vehicles which are not at one of the integration levels above is available, it will be communicated promptly. WARRANTY INFORMATION Not applicable. [ Copyright (c)2013 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15702.1.B11071... 11/12/2013

The Service Engine Soon (MIL) lamp is on and the following faults are stored in the DME fault code memory. BN2000 (E-Series) vehicles: * 2D22: Oxygen sensor downstream of catalytic converter, electric: open circuit BN2020 (F-Series) vehicles: * 12AB04: Oxygen sensor downstream of catalytic converter, electric: open circuit * 12AC04: Oxygen sensor downstream of catalytic converter 2, electric: open circuit These faults may occur sporadically after a long MSA engine stop. Unfavorable DME software diagnostics (fault is erroneous) This software error affects vehicles produced from 3/2013 to 6/2013, as well as older vehicles which have been programmed during service work to a current integration level of Xxxx-13-03-5xx.

The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised for a few seconds so the engine does not stall This can occur most frequently at outside ambient temperatures between -15C and + 15C. It is possible that the Service Engine Soon (MIL) lamp is on with misfire fault(s) stored, but it is equally possible that there will be no faults stored in the DME. Unfavorable DME software Cold start or idling problems may arise due to poor fuel quality. The use of summer fuel during cold outside temperatures may also lead to such problems.

The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

INFORMATION Not applicable.

INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).

When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.

Refer to the following applicable SIBs before replacing the valve seals. * B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair * B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints * B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity * B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. * Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption * Spark plugs fouled with engine oil and excessive engine oil consumption * Excessive engine oil consumption All Vehicles: On vehicles, where an excessive oil consumption between services is the only complaint, a complete oil consumption test as described in SI B11 03 13, must be performed first before replacing the valve seals. On vehicles exhibiting reproducible smoking from the tailpipe when hot, additional engine diagnostic steps (e.g. engine compression test, leak-down tests; inspection of the crankcase ventilation lines and turbo intake/outlet tubes for excessive oil accumulation) should be performed and documented prior to replacement of the valve seals, in order to eliminate other possible causes. Refer to the SIBs listed above for important diagnostic tips. Do not remove the intake manifolds to clean the intake valve carbon.

The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

Customers with one of the vehicles above may complain that the engine's oil consumption is "too high," resulting in engine oil top-ups and workshop visits to address the issue before the vehicle displays an engine oil service as being "due." When the vehicle's engine oil drops to the minimum level, a message will display in the vehicle advising the driver to "add 1 quart of engine oil." After topping up and continued operation, the "add engine oil" message may display again before an engine oil service is required and performed. CAUSE Engines that are fitted with a turbocharger, as part of their normal operation, will consume engine oil at a higher rate than a naturally aspirated engine (non-turbocharged engine). In this case, a "turbocharged" engine could require topping up of the engine oil more frequently.

Certain of the following US-specification BMW vehicles sold or leased in the United States and Puerto Rico are included.

VEHICLES (MODELS) Certain models of the following US specification BMW vehicles sold or leased in the United States and Puerto Rico are included.

Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.

The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.

This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil

The customer complains that the "low engine oil" message is displayed too frequently. CAUSE The cause is related to, but not limited to, one or more of the following components and systems shown below: z Turbocharger z Crankcase ventilation z Engine gasket leaks z Internal engine tolerances and sealing z Improper filling or topping up Use the troubleshooting procedure below to help identify the cause.

The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. * Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting

The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts

The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or idling, the engine will misfire and the Service Engine Soon lamp is illuminated. ? Various misfire faults are stored in DME fault memory. CAUSE An internal failure of the high-pressure fuel injector can lead to incorrect operation.

INFORMATION This bulletin outlines the procedure to check the engine timing chains for wear and should be completed in conjunction with SI B11 06 14 "N63 Customer Care Package". Performing the test plans identified in the procedure below will detect wear at an early stage and if necessary provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to assure the highest standard of performed repairs.

When performing the scheduled oil service and filling the engine with the amount specified, the applicable ISTA/D repair instruction does not require performing this test plan. Applicable models: ? F01 and F02 with the N63T engine with I-Level F001-13-03-501 or higher ? F06, F07, F12 and F13 with the N63T engine with I-Level F001-13-03-501 or higher ? F10 with the N63T engine with I-Level F010-13-07-501 or higher ? F15 and F16 with all I-LevelsTest plan path: 1. Select "Service Function." 2. Select "Drive." 3. Select "Motor Electronics." 4. Select "Motor Oil."5. Select "Oil Level." 6. Select "Continue." 7. Follow the steps as directed in the test plan to complete the measurement. Always refer to ISTA/D for the recommended oil type and the amount required, using the VIN number of the vehicle. IMPORTANT: Do not perform this test plan on the following vehicles: ? Performing the test plan on any vehicle with the N63 engine will result in an inaccurate measurement. ? Performing this test plan on any vehicle with the N63T engine without the applicable I-Levels stated above will result in an inaccurate measurement. Do not perform this test plan when performing engine oil services. Fill the engine with the specification found in ISTA/D. WARRANTY INFORMATION Not applicable. [ Copyright (c)2014 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20361.1.B110713....1/2/2015

Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its "class leading" power and performance. To ensure these engines keep delivering the ultimate performance, we have designed this Care Package that includes a 6 point check, and if necessary, the replacement of one or more of the following powertrain components: ? Hot-Film Air Mass Sensors ? PIEZO High Pressure Fuel Injectors ? Engine Vacuum Pump ? Fuel System Low Pressure Sensor/Feed Line ? Fresh Air Intake Turbo Seals ? Crankcase Ventilation Lines (Hoses) This engine care package also includes a multi-point inspection of the vehicle, including tire pressures, fluid levels, safety and convenience features. The procedure described in this bulletin should be completed in conjunction with performing SI B11 16 14, N63 Engine: Check the Timing Chain. Perform all recommended, due or qualifying "time-based" maintenance service tasks as directed by the Key Reader/ISPA Light application. Note: The procedure in SI B11 16 14 includes an engine oil and filter change. When applicable, also perform the procedure described in SI B61 30 14, 12-Volt Battery Replacement under the BMW Maintenance Program together with performing the N63 Customer Care Package. After completing all necessary repairs, vehicle needs to be test driven for up to 30 minutes to assure the highest standard of performed repairs.

ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller. CAUSE The KAFAS (camera-based driver support system) camera is affected by environmental conditions such as: * Direct sunlight (sunrise or sunset) * Rain * Fog * Dirt * Snow * Ice * High interior temperatures (may also cause a CCM to be displayed upon starting the vehicle) ?? Fault code 0x800AC0 - KAFAS camera switch off due to over temperature The pictures below show the direct sunlight causing the CCM: INFORMATION This is the current text in the Owner's Manual for the Front Collision Warning (FCW): The system may not be fully functional in the following situations: * In heavy fog, rain, sprayed with water or snowfall * In tight curves * If the driving stability control systems are limited or deactivated: for example, the DSC is off. * If the camera view field of the front windshield is dirty or covered. * Up to 10 seconds after the start of the engine, via the Start/Stop knob. Direct sunlight will be added as one of the causes for the FCW CCM.

On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut

The Drivetrain Malfunction message is displayed and any of the following faults for the quantity control valves are stored in the DME. 11C302 - Fuel- supply control valve 2, activation: short circuit to ground or open circuit 11C401 - Quantity control valve, activation: short circuit to ground 1F4C04 - Relay, quantity control valve: open circuit The most likely cause is the high fuel pressure quantity control valve relay (K6342) loose connection at the electrical connector.

Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.

The Service Engine Soon light comes on with either or both of the following faults stored in the DME memory: ? 12B701 - Oxygen sensor heating after catalytic converter, function: Internal resistance too high ? 12B801 - Oxygen sensor heating after catalytic converter 2, function: Internal resistance too high The engine operation and performance are not affected. The DME diagnosis for the post catalyst oxygen sensor(s) is too sensitive.

designates changes to this revision SUBJECT N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) did not work correctly with ISTA/P 3.54.x or 3.55.0. It did not change the interval to the desired 12 months/10,000 miles for the vehicles listed above in the specified production ranges. The ""Conversion, oil service 12 months/15,000 km/10,000 miles"" is working properly for all other N63 vehicles produced after these dates. Incorrect coding data in the affected ISTA/P versions"

conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label."

INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled ""N63: Drivability after CCP."" Follow the recommendations received."

The ""Drivetrain Malfunction"" Check Control Message is displayed when driving under certain engine operating conditions and at high altitude (above 6500 ft/2000 m). The engine has reduced power until the ignition is cycled off and back on. In this situation, the following faults would be stored in the DME(s) memory: z 120208 - Charging pressure control, plausibility Pressure too high z 120608 - Charging pressure control 2, plausibility Pressure too high z 120408 - Charging pressure control, Switch-off as consequence z 120908 - Charging pressure control 2, Switch-off as consequence DME diagnostic threshold error."

""Drivetrain Malfunction"" message displayed with reduced engine power. Erroneous misfire faults may be stored for cylinders 3 and 6. The situation is most likely to occur after driving for several hours at constant highway speeds with light throttle (low load and low engine speed). Cycling ignition off and back on again clears the ""Drivetrain Malfunction"" warning DME software (plausibility check error)."

The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.

designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72 vehicles with the N63 engine produced from January 1, 2011 to December 1, 2011. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. CAUSE The high-pressure pump quantity control valve may fail."

Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil

designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."

No sound from the radio, telephone, gong signal and or PDC. Poor radio reception and failure of the telematics systems. Possible Check Control system message: o Battery discharge when engine off. o Caution, no acoustic warning signals. Non BMW approved (third-party supplier) USB cable plugged into the USB port.

July 2014 What's New: Model - Removed models which no longer support BMW Assist functionality and added new models. Procedure - Add step requesting print out of ConnectedDrive Service Cockpit page Information - Add SI for ConnectedDrive Service Cockpit; updated the hyperlinks and email address for CD support team; deleted scenario for old CDMA unit which are no longer supported. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.

Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption Spark plugs fouled with engine oil and excessive engine oil consumption Excessive engine oil consumption Vehicles with less than 40,000 miles should not be considered for valve seal replacement. All Vehicles: A complete oil consumption test, as described inSI B11 03 13, must be performed first, before replacing the valve seals. Do not remove the intake manifolds to clean the intake valve carbon.

added ? "Models" updated: Model Year G12 (7 Series) excluded from program ? "Procedure" updated: N63R engine added to 2016 Model Year G12 (7 Series) ? Attachment updated with G12 (7 Series) production date range for 2016 Model Year. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is "applicable" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

injector type using the ISTA test plan ? Determining the injector part number using the new the parts table. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.

indentifying injector type using an ISTA test plan. . The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.

format updated ? Consequential Additional Repair(s) statement added ? Overlapping Labor Procedure statement added . The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM rubber material. The FPM rubber material is engine heat resistant. Or The plastic coggurated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.

This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.

capacity specification for all vehicles with the N63R engine and xDrive.

This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.

"track day" cars some of which may be used on both track and highway. SB 23-01 adresses proper installation torque of cap bolt fasteners attaching SPL's aftermarket lower control arms, recurring inspection and confirmation of torque setting and removal and replacement of damaged or under torqued fasteners to reduce risk of premature failure and accident. SB-23-01 was mailed, emailed and posted on SPL website to known resellers, race teams and users of the affected parts and is being submitted here as required by part 579.5. Vehicle Applications include: BMW series 1,2,3,& 4, 2008-2023; Chevrolet Camaro 26-2023, Cadillac ATS, CTS 2016-2019; Ford Mustang 2015-2023; Toyota Supra 2020-2023.

Extension For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's Rear Monitoring Oxygen (O2) Sensors (one shown) to: 10 years/120,000 miles as determined by the vehicle's original in-service date This component-specific limited warranty extension applies to defects in materials or workmanship.

What's New: The F01 (750i xDrive Sedan) production start date has been corrected The Correction and Warranty Information sections have been updated The Parts Information section has been updated.

Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.

INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure.

INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

Fluctations of fuel level (causing resistance changes in the level sensor) while vehicle is stationary, are interpreted as refueling. This causes active ECO PRO mode bonus range to reset. Error in instrument cluster application.

For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.

After the vehicle is started, a Check Control message ""High Battery Discharge Warning"" is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAS - ""930769 Deactivation of terminal 15: upper startability limit reached"" CAS - ""93076A Deactivation of terminal 15: upper startability limit reached, but deactivation preventer or legal load/consumer active"" CAS - ""93076B Deactivation of terminal 30B: upper startability limit reached"" CAS - ""93076C Deactivation of terminal 30B: upper startability limit reached, but deactivation preventer or legal load/consumer active"" JBE - ""8020E8 Reset or deactivation of terminal 30F"" DME - ""213901 Power management: reduction or deactivation of individual electrical loads/consumers"" CAUSE The battery has become heavily discharged or is faulty. The following reasons can contribute to a prematurely failing battery: * Unfavorable driving profile - excessive short trips * Excessive terminal 30B after run - normal coolant pump or electric fan operation * Extremely cold temperatures * Vehicle faults - closed circuit draw, sleep mode preventer or frequent wakeups"

An emergency call is erroneously made with no input from the driver. The following fault codes are stored in the TCB: * 0xB7F325 - Emergency call loud speaker: break in circuit * 0xB7F319 - Emergency call button: short circuit * 0xB7F326 - Emergency call loud speaker: short circuit to earth * 0xB7F33E - Automatic emergency call triggered frequently CAUSE TCB control unit error

Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery. The analysis and testing of the battery's SoC (Stateof Charge) and SoH (State of Health) is now performed using ISTA (Integrated Service Technical Application) diagnosis. A separate test using a battery tester is no longer needed.

1. The low beam flashes briefly after the ignition is switched ON. This situation can be duplicated every time the vehicle is started. 2. One of the faults below is stored and currently present: 0xDA1411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC 0xD9D411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC Faulty LED main light module (LHM2)

A headlight malfunction CC message is displayed for one or more of the following lights: -Daytime driving light -Turn indicator -Dipped headlight -Main beam The following fault codes in the FRM are stored: -800FC8 LIN bus, headlight driver module (TMS), left: communication fault -E58522 No message (status, exterior lights, front electronics 1, left, 0x1E0), receiver FRM, transmitter TMSL Software error in TMS 3 (headlight driver module AHL); a software I-level lower than 14-07-503 will cause the above situation to occur.

After the vehicle is started, a Check Control message ""High Battery Discharge Warning"" is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAS - ""930769 Deactivation of terminal 15: upper startability limit reached"" CAS - ""93076A Deactivation of terminal 15: upper startability limit reached, but deactivation preventer or legal load/consumer active"" CAS - ""93076B Deactivation of terminal 30B: upper startability limit reached"" CAS - ""93076C Deactivation of terminal 30B: upper startability limit reached, but deactivation preventer or legal load/consumer active"" JBE - ""8020E8 Reset or deactivation of terminal 30F"" DME - ""213901 Power management: reduction or deactivation of individual electrical loads/consumers"" CAUSE The battery has become heavily discharged or is faulty. The following reasons can contribute to a prematurely failing battery: * Unfavorable driving profile - excessive short trips * Excessive terminal 30B after run - normal coolant pump or electric fan operation * Extremely cold temperatures * Vehicle faults - closed circuit draw, sleep mode preventer or frequent wakeups"

Hill Descent Control is inoperative after programming the vehicle with ISTA/P versions 2.49.0. or 2.49.1. Central Gateway Module software error.

One or more of the following Check Control Messages (CCM) will be displayed on the Central Information Display (CID): * Adaptive light system defective * Front left or right lighting system defective * Automatic headlight range adjustment defective Additionally, one or more of the following symptoms may occur: * Both low-beam headlamps point in the downward direction. * The turn signal indicator in the KOMBI flashes rapidly. CAUSE Software error in the Footwell Module (FRM)

The Head-up Display (HUD) is too dark. Rain/light/solar/condensation sensor (RLSB) hardware error

or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances. Work time labor operation code 61 00 006 is not considered a Main labor operation; however, it does require an individual punch time and an explanation on the repair order and in the claim comments Vehicle Programming and Coding When ISTA/P automatically reprograms and codes all the vehicle's control modules that currently do not have the latest software, and if control module failures occur during this programming procedure: ? Please claim this consequential control module-related repair work under the defect code listed in this bulletin with the applicable KSD2/AIR labor operations. Other Repairs Control module failures that occurred prior to this programming procedure and/or additional work is performed as a result of performing the ISTA diagnostics and related test plans: ? When covered under an applicable limited warranty, claim the control module-related and/or other repair work using the applicable defect code and labor operations in KSD2/AIR.

Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.

If termination of vehicle programming occurs due to: A. Undervoltage (when the vehicle is connected to an approved battery charger/power supply) B. Lost connection to the server C. Termination by the control module D. Termination by ISTA/P E. ICOM connector removed/falls out Then the DSC module may no longer communicate when connected to ISTA/D or ISTA/P. As a result, the DSC module cannot be reprogrammed. DSC software

The vehicle is locked with one remote key and then enters sleep mode. The vehicle is then unlocked using one of the outside door handles with the second remote key. The outside door mirrors do not move to the correct position. The seats do move into the correct position. CAUSE Software error in driver's seat module

Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID.

designates changes to this revision SUBJECT Door Open Message Displayed, Even Though Door Is Closed. While driving, a CCM (Check Control Message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. The FRM (Footwell Module) sees an incorrect door lock status caused by voltage variations in the door locks.

Sporadically the vehicle cannot be started, due to a discharged battery caused by a software glitch in the instrument cluster.

INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

designates changes to this revision SUBJECT High Battery Discharge Warning: Battery Needs Replacement. After the vehicle is started, a Check Control message ""High Battery Discharge Warning"" is displayed in the Central Information Display (CID). Various power supply and power management faults are stored, including the following: CAS - ""930769 Deactivation of terminal 15: upper startability limit reached"" CAS - ""93076A Deactivation of terminal 15: upper startability limit reached, but deactivation preventer or legal load/consumer active"" CAS - ""93076B Deactivation of terminal 30B: upper startability limit reached"" CAS - ""93076C Deactivation of terminal 30B: upper startability limit reached, but deactivation preventer or legal load/consumer active"" JBE - ""8020E8 Reset or deactivation of terminal 30F"" DME - ""213901 Power management: reduction or deactivation of individual electrical loads/consumers"" CAUSE The battery has become heavily discharged or is faulty. The following reasons can contribute to a prematurely failing battery: z Unfavorable driving profile - excessive short trips z Excessive terminal 30B after run - normal coolant pump or electric fan operation z Extremely cold temperatures z Vehicle faults - closed circuit draw, sleep mode preventer or frequent wakeups."

designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. ? The calculation is based on the current date of repair. It is ""applicable"" when the 12-volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

INFORMATION For the above-referenced vehicles, BMW of North America, LLC (""BMW NA"") is extending the limited warranty for the pressure switch, leak diagnosis module (NVLD) to: 10 years/120,000 miles as determined by the vehicle's original in-service date Note: This bulletin is notice of a ""limited warranty extension."" This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem. Customer Notification Letter - VIN and Component-specific Warranty Extension Even though this is NOT a Recall, BMW NA will be sending VIN-specific customer notification letters in a phased release."

According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Front passenger seat occupancy detection transmitting fault (moisture)"" is stored. The fault may or may not currently be present. The front passenger seat occupancy mat consists of a seat occupancy mat with a capacitive sensor system. This means a front passenger is detected by measuring the resistance of the human body. The fault is set when moisture is detected on the mat itself."

electronics

The ?top up coolant? message is displayed in the central display (CC message ID 166). When checking the cooling system there are no leaks found and the expansion tank is filled to the proper level.

Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.

The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.

Messages can be sent to the vehicle and are received as indicated by the envelope icon displayed in the CID. However, the menu option ""Message,"" used to retrieve or access messages, is no longer available in the iDrive menu. CAUSE Software error with ISTA/P 2.49.2 to 2.49.4 I-Level F001-13-03-503 to F001-13-03-505"

INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!

There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.

Poor Satellite Radio reception CAUSE After this software update there is a slight improvement in Satellite Radio reception for these vehicles when receiving their signal from XM Satellites. This is due to the changeover from Sirius Satellite broadcasting to XM Satellite broadcasting in 2016 (See SI B65 19 15).

While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software

The navigation system cannot be activated when entering the 20-digit INITIAL enabling code manually. This occurs after the Pre-Delivery Inspection (PDI) for the vehicle was already performed and finished. The wrong 20-digit ""enabling code"" was entered during the first attempt; the Headunit-High locks up and the correct ""enabling code"" will not be accepted."

One or more of the following situations may occur concerning the illumination of the Bang & Olufsen sound system loudspeakers: * Illumination is insufficient (not bright enough) * Illumination is not available on all loudspeakers * Brightness cannot be adjusted Loudspeaker illumination settings are dependent on the model: * Different brightness characteristics * Not all loudspeakers are illuminated INFORMATION Explain to the customer that loudspeaker illumination can vary from model to model. For an overview of the illuminated loudspeakers, refer to the attachment. IMPORTANT: The current version of the Owner's Manual for 5 Series vehicles is incorrect. On 5 Series vehicles (F07 and F10), only the main loudspeaker (moving part) in the dashboard and the two loudspeakers in the mirror triangles in the front doors are illuminated. The Owner's Manuals for 5 Series vehicles will be corrected with start of production of the MY2014 vehicles (July 2013).

The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly

INFORMATION Do not replace parts and do not perform a repair attempt! Explain to the customer that loudspeaker illumination can vary from model to model. For an overview of the illuminated loudspeakers, refer to the attachment. IMPORTANT: The current version of the Owner's Manual for 5 Series vehicles is incorrect. On 5 Series vehicles (F07 and F10), only the main loudspeaker (moving part) in the dashboard and the two loudspeakers in the mirror triangles in the front doors are illuminated. The Owner's Manuals for 5 Series vehicles will be corrected with start of production of the MY2014 vehicles (July 2013). This Service Information will be updated as soon as a solution is available for adjustment of the brightness of the illuminated loudspeakers. A software solution is expected to be available with ISTA/P 2.50.0 in July 2013.

The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.

INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z However, it does not transfer the contact list (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle they must unlock the phone (passkey) With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the "Attachment" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following: z www.bmwusa.com/bluetooth website NOTE: This SI will be updated as new information is received.

Speed limit information (SLI) is not displayed in the Kombi or the Head-Up Display (HUD). This only affects the specific VINs (vehicle identification numbers) listed below. The vehicle was built incorrectly (without option 8TH).

After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.

Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation.

INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the ""Attachment"" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received. "

The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H

Media connected to the USB connector is not recognized by the audio system. Playback of files from the media is not possible. Message displayed on the audio system display: ""Title cannot be reproduced"" ""Is being read"" (but never plays back any audio) CAUSE Media with data files stored in more than 32 directories or 32 subdirectories within a directory. Media with a large number of files. Media exceeds total storage capacity of 32 GB."

cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.

What's New: ? Model: Option code removed to prevent confusion about affected vehicles ? Situation: Information added about Bluetooth functionality that is not affect by this Service Action ? Correction: Information added about lease returns, loaner, CPO and used vehicles that are not eligible for the 3 customer options ? Information: Removed scenario regarding new/unsold Z4s & X1s ? Procedure: Added info about COMBOX retrofit that it does not affect Bluetooth functionality ? Warranty: Added info that the correct flat rate labor operation that corresponds to the option the customer selected is claimed and removed information about Z4s & X1s . The underlying 2G technology for the GSM (Global System Mobile communication) COMBOX will no longer be supported by the cellular network providers after December 31, 2016. This COMBOX and the BMW Assist services that use its functionality will therefore no longer function after that date. The BMW Assist functionalities that are affected includes the following: SOS/E-Call including Automatic crash notification Concierge Service Remote Service Teleservices The vehicle's exisiting Bluetooth(r) wireless functionality is NOT affected.

INFORMATION As of 11/2015, all Entry-NAV/Media head units supplied in new vehicles were upgraded for improved noise characteristics and quality. As a part of this upgrade, the hardware updating the sender lists was changed from an "update after every diversity reception interruption or maximum of four minutes" configuration to "regular interval updates (every four minutes) without regard to diversity reception status" configuration. This may cause a delay of up to four minutes for updates to the sender list when leaving areas of poor reception. The last received transmitter, before the entrance into underground car parking or a tunnel, is still received and will show station identification. This fixed interval update does not apply to Traffic Message Channel updates which remain active. This new equipment operation pattern may be noticed by the customer after replacement of their Head unit. All replacement Head units delivered since 01/2016 have the upgraded design. An immediate solution would be for the customer to select one of their stored favorite stations via the menu or favorites buttons. PARTS INFORMATION Parts exchange or a software update are not effective or approved for this situation. WARRANTY INFORMATION Not applicable."

While importing a CD to the internal music collection of an NBT head unit the process aborts. You will see 'import error' on the radio display when this occurs. NBT Head Unit software

When the instrument cluster's digital speedometer has been set to display metric speed and distance values, there is no display of the miles per hour. US regulations specify that even with the instruments set to display metric values, a ""Miles per hour"" display must also be present for immediate visual reference. To confirm language settings use the iDrive controller: Menu, Vehicle Settings, Language/Units, then - Distance - Dig (digital) Speedometer Instrument Cluster (KOMBI) software error."

randomly switches to BMW Apps (Pandora, Spotify, Audible etc.) with no input from driver or passenger.

starting or while driving.

Groaning noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or over uneven road surfaces. CAUSE Hydraulic mount in tension strut

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

When the heating and air conditioning system is first turned on, a grinding noise may be heard from the right side of the front center console. CAUSE The bushing of the blending flap for the rear seat outlet lacks sufficient grease.

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

Tailgate does not stay in fully open position.

During inspection, the rear differential mount in the rear axle support shows signs of cracking.

Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)

This service Information bulletin provides information on shipping "specific" noin-deployed vehicle safety devices that are classified as Dangerous Goods (DG) to Lighting resources, LLC

It designates changes to this revision SUBJECT Moisture in LED Headlight . INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.

After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. AFFECTED VEHICLES This Service Action involves F01, F02, F04, F06, F07, F10, F12, F13 and F25 vehicles which were produced August 2010 to June 2012. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair."

A Check Control message shows ""Emergency call failure."" When the SOS button is pressed, the call is not made by the TCB (Telematics Communication Box). Fault code 0XB7F33F is stored in the TCB. CAUSE TCB application error"

After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for code number 637. If code number 637 has been punched out, the campaign has already been performed. If code number 637 has not been punched out, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Important Note: A campaign can be reserved in ISPA Light as ""Pending"" prior to submission of a claim. If you find this campaign reserved, please verify the reason before attempting to perform this repair."

Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns, starting with claim repair dates on or after September 1, 2014. As part of our pledge to deliver the ultimate BMW driving experience, for the above-referenced BMW vehicles, we developed this program to increase our customers' satisfaction by helping to prevent unexpected repair visits.

Based on customer feedback, BMW has determined that during the first three years of service, some vehicles may require specific additional service work. BMW of North America, LLC ("BMW NA") is pleased to announce the Customer-Focused Satisfaction (CFS) Program. This new program's procedure will be available for your center to address these customers' concerns, starting with claim repair dates on or after September 1, 2014. As part of our pledge to deliver the ultimate BMW driving experience, for the above-referenced BMW vehicles, we developed this program to increase our customers' satisfaction by helping to prevent unexpected repair visits.

Injectors to 10 years/120,000 miles as determined by the vehicle's original in-service date.

The integrated owner's manual (IBA) is no longer accessible after programming the vehicle with either: ISTA/P 3.57.3 (F001-15-11-505) ISTA/P 3.58.0 (F001-16-03-501) ISTA/P 3.58.1 (F001-16-03-502) ISTA/P software error

The route guidance to an address selected from the iPhone address book is inoperative. The navigation system integrated into the Headunit-High (HU-H) is not accepting addresses from the iPhone address book when the state (part of the address) is stored in the abbreviated form (e.g., NY instead of New York).

The SIRIUS/XM satellite radio (SDARS) stations cannot be stored in the PRESET menu. * No fault code related to this issue is stored in the HU-H. * AM/FM radio stations are not affected; they can be stored correctly. Software error in the SDARS control unit integrated in the Headunit-High (HU-H)

The vehicle position on the navigation map is incorrect. With route guidance active, the vehicle is displayed: * In an incorrect location Or * Outside the planned route The navigation system integrated in the Headunit High (HU-H) is not calibrated correctly.

designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.

tank.

v. BMW of North America, et al. The Court has granted final approval of the settlement. The Settlement Benefits are effective and available on and after February 9, 2022.

v. BMW of North America, et al. The Court has granted final approval of the settlement. The Settlement Benefits are effective and available on and after February 9, 2022.

Wrong coding in the spare part from the supplier

along with 6AC option code ? Situation: All information added ? Information: Deleted CDMA related information and added activation of Wi-Fi control unit ? Procedure: Added "Note" regarding ConnectedDrive support hotline information . A replacement telematics control unit must only be activated for vehicles with an active BMW Assist subscription. Note: 2G CDMA and 2G GSM telematics control units cannot be activated because they are no longer supported and the supporting network(s) have been decommissioned. INFORMATION The following changes have taken place: All Telematics control unit replacements must be activated by Part managers via the DCSnet application. New steps included in the procedure for activating Telematics control unit replacements for vehicles equipped with Wi-Fi Hotspot (6WD)."

Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.

A rattling or clattering noise may be heard from the front passenger's side footwell area when driving on rough roads. CAUSE The front passenger's footwell trim makes contact with the side cover of the instrument panel.

This Service Action involves F01, F02, and F04 7 Series models 2009 to 2014. Only vehicles which require this Service Action to be completed will show it as ?Open? when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader."

If the customer profile is assigned to only unlock the driver door after programming with ISTA/P 3.55.x, the trunk will not open with the remote. CAUSE Coding error in CAS (Car Access System) for trunk locking

operation may be the contactless tailgate (Smart Opener) opens / close unintentionally from objects in the vicinity of the rear of the vehicle; for example by a gas filling hose.

A fault in the parking brake (EMF) switch could cause a Check Control message (Parking Brake Failure) to display. However, all braking functions, including the parking brake and switch continue to operate properly in this case. Affected vehicles in center inventory must not be delivered until the parking brake switch has been replaced. Parking brake switches for the F15 must be ordered VIN-specific. Refer to Service Information bulletin B61 20 13 for the part number and complete instructions. Parts for the F01 and F02 are not available at this time. An availability update will be provided by November 20 (1 week).

The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model

The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. Software calculation of the brake pad wear model in the DSC.

When a vehicle comes into the workshop for any repair or maintenance job, the bundling calculator recommends a brake maintenance checkup. No brake warning light is illuminated. CBS shows 3,107 miles or slightly higher for the next brake service displayed via Key Reader, or vehicle's Control Display (in Vehicle Info/Status/Service required/Brake pads) CAUSE CBS calculates the remaining brake pad wear based on brake pressure, speed, vehicle specific parameters (i.e. NAO pads), brake temperature as well as cumulative brake application time. Due to variation of these parameters and outside environmental influences, this calculation can deviate from the real brake pad wear. Starting from the above-mentioned production dates of the vehicles indicated, the CBS brake pad wear calculation has been changed, and is now based only on the brake pad wear sensor. Important Note: To avoid a too-slow wear prediction, the CBS brake model will estimate the need for repairs, in some cases, rather early. Calculation will level at 3,107 miles and stay at this value until the CBS brake pad wear sensor is triggered. https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/36...11/8/2016 Page 2 of 2 After the sensor is triggered, the CBS mileage will count down indicating to the customer that the brake repairs will be due.

After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.

When diagnosing the vehicle with ISTA, the FRM3 (Footwell Module) is shown as not responding in the vehicle test. The customer may report one or more of the following malfunctions: 1. Light operation * CCM (Check Control Message) ""Display failure"" * Lighting INOP * Turn signal lights INOP * Break lights INOP * License plate light INOP * Courtesy lights INOP * Instrument cluster w/o light 2. Windows * One or both front windows INOP 3. LIN components https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15625.1.B630513... 8/29/2013 Page 2 of 2 * CCM ""no blind spot detection"" if equipped * Power mirrors INOP * Seat adjustment INOP 4. Hardware inputs * Door locks INOP * Gear shifts automatically to P * Gear shift lever cannot be moved out of P 5. Electrical steering column adjustment * ELSV (Electric Steering Column Adjustment) INOP CAUSE Various causes include the following: * Blown fuse * Faulty wiring * Faulty component"

The display in the instrument cluster intermittently only shows the background image and the gear indicator. * No fault code is stored * All gauges function correctly Note: The issue is rectified after a sleep mode cycle (ignition off for approx. 16 minutes). Software error in the instrument cluster introduced with software I-level 12-03-500 or higher (ISTA/P 2.46.1 or higher)

The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)

1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.

bags.

The Head Unit-High (HU-H) resets intermittently or permanently. 1. The display is inoperative and there is no audio output 2. Automatic system start-up after a couple of seconds Fault Code E1C440 set No Fault Codes set Software error in the Head Unit High (HU-H)

Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

The ConnectedDrive Services are non-functional after a hardware exchange of the telematics control unit. This is not indicated by CC-message. ConnectedDrive Services not synchronized by Telematics Control Unit.

Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.

There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants

The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.

There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.

axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.

Intermittent steering assistance failure CAUSE The power supply of the EPS control unit.

Premature condenser failure due to corrosion. Replace the condenser if the vehicle contains the affected part number (9255983) AND the production date of the part falls on or before 11/11/13.

INFORMATION As noted in ETK: In case of surface damage to buttons, use the button cap repair kit. Use and claim the part number for the ""Repair kit for button caps"" when performing this repair. Replace ALL the buttons with those included in the kit. Note: Please do not use and claim the part number for the "Repair kit, radio and A/C panel." To ensure the button cap kit with the correct symbols and labels is installed, perform a part number lookup in ETK by VIN. Labor operation code 64 11 326 is a Main labor operation. If you are using a Main labor code for another repair, use the Plus code labor operation 64 11 769 instead."

Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION Part Number