2022 Bentley Flying Spur TSBs

Customer statement / workshop findings: One or a combination of the following symptoms are evident Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Customer statement / workshop findings: One or a combination of the following symptoms are evident: Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Customer statement: The customer may report an audible ticking noise from the top of the engine, low oil pressure warnings / MIL on the Driver Information Panel, and/or misfiring during engine operation

Customer statement / workshop findings: Poor engine running Reduced power Engine warning lamp illuminated Symptom related DTCs evident within the applicable engine control unit(s)

Customer statement / workshop findings: Sporadic entries in control units that use Nanotype terminals, including the airbag control unit J234, the engine control unit J623 and the emergency call and communication unit J949. These may be accompanied by intermittent electrical behaviour or repeated DTCs after earlier diagnostic checks.

Customer statement / workshop findings: Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services.

Customer statement / workshop findings: Engine light in the DIP - Various oxygen sensor / Fuel ratio DTCs logged within the Engine Control Module (s)

Customer statement / workshop findings: This TPI provides supplementary technical information to support diagnosis of ECM 5V reference circuit DTCs. It details the sensors associated with each reference circuit (A, B, and C) and outlines relevant guidance to assist in isolating faults when any of the following DTCs are stored in the Engine Electronics (diagnostic address: 0001) Sensor Reference Voltage A Circuit Open / High / Low (P0641, P0643, P0642) Sensor Reference Voltage B Circuit Open / High / Low (P0651, P0653, P0652) Sensor Reference Voltage C Circuit Open / High / Low (P0697, P0699, P0698)

overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Customer Statement: The customer may report one or more of the following after vehicle repairs: Engine does not start following workshop work Drive System Fault warning displayed in the instrument cluster (Kombi).

Customer Statement: The engine warning light comes on and the vehicle loses power.

This TPI provides supplementary technical information to support diagnosis of ECM 5V reference circuit DTCs. It details the sensors associated with each reference circuit (A, B, and C) and outlines relevant guidance to assist in isolating faults when any of the following DTCs are stored in the Engine Electronics (diagnostic address: 0001)

The customer may report a ticking noise from the upper engine area, low oil pressure warnings, or a flashing MIL during engine operation.

The customer may report an audible ticking noise from the top of the engine, low oil pressure warnings / MIL on the Driver Information Panel, and/or misfiring during engine operation.

Condition: Sporadic entries in control units that use Nanotype terminals, including the airbag control unit J234, the engine control unit J623 and the emergency call and communication unit J949. These may be accompanied by intermittent electrical behaviour or repeated DTCs after earlier diagnostic checks.

Customer Statement: The engine warning light comes on and the vehicle loses power. Workshop Findings: Customer statement can be verified and the following entries may be logged within the engine control unit. P029900: Turbo/Super Charger Under-boost, passive/sporadic.

Condition: The belt tension damper is exhibiting oil leakage or signs of residual oil staining.

One or a combination of the following symptoms are evident Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Condition: One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP

Condition: Engine light in the DIP - Various Camshaft adjuster DTCs logged within the Engine Control Module(s)

One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP Or Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident, in this scenario the operative should also refer to TPI 2051893/-

Customer statement: Engine cooling system overheating And/or Coolant loss And/or Warning light in Drivers Information Panel (DIP)

Technical Background: The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Condition: Poor engine running Reduced power Engine warning lamp illuminated Symptom related DTCs evident within the applicable engine control unit(s)

Condition: Multiple random cylinder misfire DTCs detected during PDI - DTC P030000: Random/Multiple Cylinder Misfire Detected (misfires on multiple cylinders) within the following control units: V8 - ECM 1 - V8 (Address 01) ECM control unit W12 - ECM 1 - (Address 01) and/or ECM 2 (Address 11)

Technical Background: An important factor of influencing the cooling system efficiency is the water used in the mixture Due to the different ingredients and characteristics existing in each country or even region, Bentley has decided to define the quality of water for cooling systems

Customer statement: Customer unable to intermittently start the engine with the start button Or Engine starts but customer gets a pop up error within the Drivers Information Panel (DIP)

One or a combination of the following symptoms are evident Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP Or Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident, in this scenario the operative should also refer to TPI 2051893/-

Condition: Poor engine running Reduced power Engine warning lamp illuminated Symptom related DTCs evident within the applicable engine control unit(s)

Condition: HVAC distribution/operational issues HVAC motor defect (DTCs) evident within address 08 - Climatronic control unit, the DTCs can be static or Intermittent

Condition: Torque values for ancillary components (used during engine replacement) are not currently available within the Repair manual The affected components and torque values are as listed within the Technical background section of this TPI

Condition: Engine oil level requires top up between services Technical Background: The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Condition: Multiple random cylinder misfire DTCs detected during PDI - DTC P030000: Random/Multiple Cylinder Misfire Detected (misfires on multiple cylinders) within the following control units: V8 - ECM 1 - V8 (Address 01) ECM control unit W12 - ECM 1 - (Address 01) and/or ECM 2 (Address 11)

Condition: One or a combination of the following symptoms are evident: Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Condition: Engine oil warning lamp illuminated within the Drivers Instrument Panel (DIP) Engine oil requires topping up between services Excessive engine oil consumption

Condition: Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services.

Customer statement: Engine coolant overheat warning within the DIP

Technical Background: An important factor of influencing the cooling system efficiency is the water used in the mixture Due to the different ingredients and characteristics existing in each country or even region, Bentley has decided to define the quality of water for cooling systems Demineralised water according to standard VDE 0510 meets all requirements and can be purchased worldwide Therefore undiluted coolant should be mixed in the correct ratio using demineralised water as detailed in Elsa Pro coolant specification, this will detail the ratio and type of coolant to use The use of desalinated water in the engine cooling system is specifically prohibited

Condition: Engine management light illuminated within the DIP DTC P025C00 Fuel Pump Module Control Circuit Low is evident within 0001 (Engine control unit)

Customer statement: Engine MIL light illuminated within the DIP Workshop findings and observations: DTC P04F000: EVAP system high pressure purge line performance evident

following symptoms are evident Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Customer statement / workshop findings: Oil leak evident from the rear shock absorber/s (Left and/or Right

Customer statement / workshop findings: Engine light in the DIP - Various oxygen sensor / Fuel ratio DTCs logged within the Engine Control Module(s).

Customer statement / workshop findings: Engine light in the DIP - Various Camshaft adjuster DTCs logged within the Engine Control Module(s).

Customer statement / workshop findings: DTC P218100 - Cooling System Performance and / or DTC P1BB400 Cylinder head temperature too low is stored in the Engine Control Module (ECM). Emission Control Lamp illuminated on the Driver Instrument Panel.

Customer statement: Engine coolant overheat warning within the DIP

Customer statement Customer unable to intermittently start the engine with the start button Or Engine starts but customer gets a pop up error within the Drivers Information Panel (DIP).

Technical background It is possible for the engine coolant Thermostat to corrode over time, this corrosion is due to an adverse reaction of the Thermostat material with the engine coolant. The corrosion and subsequent build-up of debris prevents the correct operation of the thermostat when closing, resulting in over cooling. The ECM triggers a DTC when the target engine temperature is outside of the specified parameter.

Customer statement / workshop findings: One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP Or Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident, in this scenario the operative should also refer to TPI 2051893

Customer statement / workshop findings: One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP Or Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident in this scenario the operative should refer to TPI 2051893/-

Customer statement / workshop findings: One or a combination of the following are evident: - DTCs P008700 and / or P008800 are evident within the master and/or slave engine control modules - Emission control warning lamp (Figure 1) illuminated within the Drivers Information Panel (DIP) - The Max engine speed 4000 rpm warning lamp may also be evident within the Drivers Information Panel (DIP) as shown in Figure 2

Customer statement / workshop findings: One or a combination of the following are evident: - DTCs P008700 and / or P008800 are evident within the master and/or slave engine control modules - Emission control warning lamp (Figure 1) illuminated within the Drivers Information Panel (DIP).

Customer statement / workshop findings: - Customer reports an engine overheat warning within the DIP - Engine overheating - Unusual cooling fan operation at high temperatures - There are no obvious signs of coolant leaks both internally or externally Workshop findings - P19F700: Low engine coolant temperature indicator lamp Coolant too warm - Signs of coolant in the vacuum hoses (Refer to the video on the Bentley Hub referencing TPI 2061369.

Customer statement / workshop findings: One or a combination of the following are evident: - DTCs P008700 and / or P008800 are evident within the master and/or slave engine control modules - Emission control warning lamp (Figure 1) illuminated within the Drivers Information Panel (DIP).

Customer statement / workshop findings: Engine oil warning lamp illuminated within the Drivers Instrument Panel (DIP) Engine oil requires topping up between services. Excessive engine oil consumption.

Customer statement: Customer reports a red engine coolant overheat warning within the DIP Workshop findings. One or a combination of the following DTCs are evident within the engine control unit: - P218100 - Malfunction in cooling system - P017B00 - Cylinder head temperature sensor implausible signal - P017C00 - Cylinder head temperature sensor short circuit to ground - P017E00 - Cylinder head temperature sensor open circuit/loose contact.

Customer statement - Engine warning lamp illumintaed within the DIP And/or - Whistling noise(s) from the Inlet manifold Workshop findings: Oil leak between the oil separator tank and the Bank 1 breather line connection

Customer statement / workshop findings: Warning on the Driver Instrument Panel (DIP) - Oil pressure too low DTCs relating to oil pressure may also be stored within the Master ECU. Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU).

Customer statement / workshop findings: - HVAC distribution/operational issues - HVAC motor defect (DTCs) evident within address 08 - Climatronic control unit, the DTCs can be static or Intermittent Technical background: Where VIN applicable the operative MUST first conduct Service Campaign EB28 (Bentayga) or EB29 (New Continental GT/GTC).

up or replacing

light illuminated within the DIP -DTC P025C00 Fuel Pump Module Control Circuit Low is evident within 0001

-Engine running rough (not refined) -Engine misfire DTCs evident -Engine management light illuminated within the DIP -Knocking noise from the cylinder head

PDI - DTC P030000: Random/Multiple Cylinder Misfire Detected (misfires on multiple cylinders) within the following control units: -V8 - ECM 1 - V8 (Address 01) ECM control unit -W12 - ECM 1 - (Address 01) and/or ECM 2 (Address 11)

with erratic engine behaviour under full throttle conditions Under acceleration the vehicle appears to be slow and unresponsive The engine appears to be underpowered during acceleration Drive System Fault warning evident within the DIP

Statement: -Engine cooling system overheating And/or Coolant loss And/or Warning light in Drivers Information Panel (DIP) as Figure 1

noise from the underside of the vehicle (front and/or rear) when driving on uneven road surfaces - DTC C1298F1 (Suspension stabilization actuator Regulation not possible) evident within diagnostic address D4 and/or D5 -Bentley Dynamic ride fault evident within the DIP

present in the sound file can be caused by worn anti roll bar bushes, the noise can appear when driving over an uneven road surface or during a large suspension input for example: Speed humps or potholes

rear of the vehicle when changing direction at low speed

Statement: -Engine warning light and max engine speed 4000 rpm warning evident within the DIP during acceleration - Warning on DIP first appears when accelerating (During boost)

Customer statement: - The Engine management light is on - Rough running and potentially poor start up performance. and/or - Engine misfires. Technical background: Debris in the fuel system can lead to a blockage in the low pressure fuel injectors, ultimately causing a cylinder misfire

Customer statement / workshop findings: Oil leak evident from the rear shock absorber/s (Left and/or Right) Technical background: Should oil be leaking from the left or right rear shock absorber as shown in Figures 1 - 2 and 3, the operative should refer to the Measure section of this TPI.

Customer statement: Customer unable to intermittently start the engine with the start button Or Engine starts but customer gets a pop up error on the Kombi. Technical background: The Access/start authorization button requires a certain amount of force applying to activate the internal switches If all 3 switches within the Access/start authorization button are not engaged multiple times in a row the above DTC will store and the customer will get a pop up on the Kombi. The engine however, will still start up.

Customer statement / workshop findings: Drive system fault active on DIP. Workshop findings: Various and/or numerous Transmission control module DTCs logged. Technical background: Loose pins within the transmission link harness to the Mechatronic unit for dual clutch gearbox -J743- connections can lead to various and/or numerous Transmission control module DTCs being logged. Carry out the checks within the Measure section of this TPI.

1)

Engine lubricating oil requires topping up between services.

suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

lamp illuminated (Figure 1) within the Driver Information Panel (DIP) in conjunction with DTC - P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow - logged within one or both engine control modules

The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances.

This can be misdiagnosed as the engine sump leaking.

Engine running rough.

Customer statement / workshop findings: - HVAC distribution/operational issues - HVAC motor defect (DTCs) evident within address 08 - Climatronic control unit, the DTCs can be static or Intermittent, NOTE: Before removing any of the following components to gain access to faulty motor(s) the operative MUST raise a technical DISS query to gain permission Hint: A current ODIS log must be attached to the technical DISS query - Dashboard assembly - Head up display unit - HVAC unit.

Customer statement / workshop findings One or a combination of the following symptoms are evident: - Engine coolant overheat condition - Coolant loss - Diagnostic trouble codes (DTCs) logged within the Engine control module/s relating to Air in the coolant system - Engine overheating issues and/or DTC P218100: Cooling System Performance symptom code 8113 is evident - Warning light within the Drivers Information Panel (DIP). Measure 1) Fully drain the cooling system - Refer to Elsa Pro Rep.Gr 19 Cooling system - To drain and fill 2) Replace the Thermostat housing (includes thermostat) - Refer to Elsa Pro Rep.Gr 19 Cooling system - Thermostat - To replace

Customer statement / workshop findings One or a combination of the following is evident: - Coolant leaking from the mechanical coolant pump - Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump - Low coolant level warning displayed within the DIP Or - Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident, in this scenario the operative should also refer to TPI 2051893

Customer statement / workshop findings: One or a combination of the following is evident: - Coolant leaking from the mechanical coolant pump - Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump - Low coolant level warning displayed within the DIP Or - Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident in this scenario the operative should refer to TPI 2051893.

Customer statement: Air suspension warning light within the DIP Workshop findings: Various suspension DTCs are evident within address 74 relating to the following: - Level control valve mechanical malfunction Or - Solenoid for the level control system (Open circuit). Technical background: NOTE: An electrical integrity check must be conducted before replacing any parts The solenoid valve block and/or control unit must be replaced first (symptom dependent) before replacing the air supply unit, in the event the issue is still evident and the air supply unit assembly is suspected as being at fault, the operative must request permission via DISS before replacing the air supply control unit assembly.

Customer statement / workshop findings: - Poor engine running - Reduced power - Engine warning lamp illuminated - Symptom related DTCs evident within the applicable engine control unit(s) Technical background: Technical Product Information (TPI) to assist retailers when diagnosing poor engine running or misfires.

Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera jet nozzle. Technical background: Please note: The photographs shown within this TPI are not based on a specific vehicle type, the procedure to replace the night vision non return valve is the same regardless of vehicle type In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the non return valve.

Customer statement Loud ticking/clatter noise can be heard from the front of the engine Workshop findings The noise is from the air conditioning compressor Technical background The operative should confirm the noise is from the compressor as detailed within the Measure section.

Background: -The engine oil pan requires removal, once removed a visual check is required to confirm if a desiccant bag and/or debris is evident

acceleration up to 30kmh/18mph a noise may be heard from the rear air springs

Customer Statement: -Coolant leaking from the mechanical coolant pump -Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump -Low coolant level warning displayed within the DIP -Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113

Statement: -Engine warning light and (max engine speed 4000 rpm) warning evident within the DIP during acceleration - Warning on DIP first appears when accelerating (during boost)

the Driver Instrument Panel -The time to reach the correct engine coolant operating temperature has increased

the Driver Instrument Panel -The time to reach the correct engine coolant operating temperature has increased

Customer Statement: -Customer reports a red engine coolant overheat warning within the DIP

Customer Statement: -Coolant leaking from the mechanical coolant pump -Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump -Low coolant level warning displayed within the DIP -Engine overheating issues and.or DTC 0218100: Cooling System Performance with symptom code 8113

and/or Right)

Customer Statement: -Knocking noise from the underside of the vehicle (front) when driving on uneven road surfaces.

Customer Statement: -Knocking noise from the underside of the vehicle (front) when driving on uneven road surfaces

Customer Statement: -Coolant leaking from the mechanical coolant pump -Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump -Low coolant level warning displayed within the DIP -Engine overheating issues and/or DTC P218100: Cooling system performance with symptom code 8113

within the DIP -Engine overheating -Unusual cooling fan operation at high temperatures -There are no obvious signs of coolant leaks both internally or externally Workshop Findings: -P19F700: Low engine coolant temperature indicator lamp coolant too warm -Signs of coolant in the vacuum hoses

following DTCs may be evident (with no specific symptom codes) -P259500: Turbocharger Speed Sensor (B) - Circuit low -P259600: Turbocharger Speed Sensor (B) - Circuit high -P257900: Turbocharger Speed Sensor (A) - Circuit range/performance

Customer Statement: -Engine coolant overheat condition

Customer Statement: -Coolant leaking from the mechanical coolant pump -Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump -Low coolant level warning displayed within the DIP -Engine Overheating issues and/or DTC P218100: Cooling System Performance with Symptom Code 8113

Customer Statement: -CDA activation/deactivation solenoid fixings -Fuel rail fixings

the Driver Instrument Panel (DIP) -The time to reach the correct engine coolant operating temperature has increased

within the DIP -Engine overheating -Unusual cooling farm operation at high temperatures -There are no obvious signs of coolant leaks both internally and externally

harness to the Mechatronic unit for dual clutch gearbox - J743 - connections can lead to various transmission communication and hardware based DTCs

Statement: -Engine cooling system overheating and/or -Coolant loss and/or -Warning light in Driver Information Panel(DIP)

Customer Statement: -The engine management light is on -Rough running and potentially poor start up performance and/or -Engine misfires

-Check engine lamp illuminated within the Driver Instrument Panel (DIP) with one of multiple DTCs as detailed below: -P310B00 Low Fuel Pressure Regulation with symptom code 2636 -P014800 Fuel Deliver Error -P0191100 Fuel Rail Pressure Sensor A Circuit Range/Performance -P018B00 Fuel Pressure Sensor B Circuit Range/Performance with symptom code 17871 -Misfire DTCs

Workshop Findings: -Front trailing arm bush found damaged/leaking as shown in figures 1 and 2

noise from the underside of the vehicle (front and/or rear) when driving on uneven road surfaces -DTC C1298F1 (Suspension stabilization actuator regulation not possible) evident within diagnostic address D4 and/or D5 -Bentley dynamic ride fault evident within the DIP

present in the sound file can be caused by worn anti-roll bar bushes, the noise can appear when driving over a uneven road surface or during a large suspension input for example: speed humps or potholes

rear of the vehicle when changing direction at low speed

intermittently start the engine with the start button or -Engine starts but customer gets a pop up error on the kombi

secondary air monitors on each cylinder bank therefore some test plans and related tasks are not currently available.

Findings: -Coolant leaking from the mechanical coolant pump -Coolant witness mark on the mechanical coolant pump although coolant is not leaking/dripping from the pump -Low coolant level warning displayed

Engine running rough.

-This can be diagnosed as the engine sump leaking

displayed, engine misfire Workshop Findings: -Event entries in engine control unit relating to cylinder misfires- excessive carbon build up to leading to cylinder leakage and spark plug foul

evident within the DIP

-The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances.

engine warning lamp illuminated.

PDI -DTC P030000: Random/Multiple Cylinder Misfire Detected (misfires on multiple cylinders) within the following control units: -V8-ECM1 - V8 (Address 01) ECM control unit -W12 - ECM1 - (Address 01) and/or ECM 2 (Address 11)

illuminated within the Driver Information Panel (DIP) in conjunction with DTC - P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow - logged within on or both engine control modules

-The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. -The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type -Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering.

-Engine running rough (not refined) -Engine misfire DTCs evident -Engine management light illuminated within the DIP -Knocking noise from the cylinder head

changed under warranty for the complaint of sound distortion, yet when tested by Bentley motors and the supplier, no fault could be found with the returned unit.

Customer Statement: -Warning on the Driver Instrument Panel (DIP) - Oil pressure too low -DTCs relating to oil pressure may also be stored within the master ECU -Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU)

(DTCs) evident within address 08 - Climatronic control unit, the DTCs can be static or sporadic (intermittent)

instrument panel -Engine Lubricating oil requires "topping up" between services

Background: -A software update to the engine control module is required.

during PDI-DTC P030000: Random/Multiple cylinder misfire detected with the following control units: -V8-ECM1-V*(Address01)ECM control unit -W12-ECM 1 - (Address 01) and/or ECM 2 (Address 11)

engine warning lamp illuminated.

from the mechanical coolant pump -Coolant witness mark on the mechanical coolant pump although coolant is not leaking/dripping from the pump -Low coolant level warning displayed

speaker due to rattling noise/sound distortion. Technical Background: -There have been instances where shaker speakers have been changed under warranty for the complaint of sound distortion, yet when tested by Bentley Motors and the supplier, no fault could be found with the returned unit.

Findings: -If the symptom present is evident during vehicle startup or similar conditions please refer to TPI 2061171 Symptoms: -Acceleration limitation with erratic engine behaviour under full throttle conditions -Under acceleration the vehicle appears to be slow and unresponsive -The engine appears to be underpowered during acceleration -Drive System Fault warning evident within the DIP

intermittently start the engine with the start button or engine starts but customer gets a pop up error on the Kombi Technical Background: -The Access/Start authorization button requires a certain amount of force applying to activate the internal switches -If all 3 switches within the Access/Start authorization button are not engage multiple times in a row the above DTC will store and the customer will get a pop up on the Kombi. The engine however will still start up.

evident within the DIP Technical Background: -The operative should lease with the customer to clarify the driving conditions in which the issue occurs, see examples below: -Duration the vehicle was driven before the issue was evident -Throttle load (harsh or light acceleration) -What gradient they were driving on (uphill/downhill/flat road surface etc) -Speed of the vehicle when the issue occurred -Road conditions for example: City driving with traffic queues

Customer statement: -Emission control warning within the DIP Technical Background: -Refer to the Measure section of this TPI -This TPI is applicable to all W12 TSI models including W12 TSI Speed models

Customer statement / workshop findings: -DTCs stored for all cylinders on Bank 1 or all cylinders on Bank 2 including multiple cylinder misfires DTC - Misfires logged in one or both engine control units - Engine warning light on - Erratic engine operation Technical background: -Refer to the Measure section of this TPI -This TPI is applicable to all W12 TSI models including W12 TSI Speed models

Customer statement / workshop findings: - Acceleration limitation with erratic engine behaviour under full throttle conditions - Under acceleration the vehicle appears to be slow and unresponsive - The engine appears to be underpowered during acceleration - Drive System Fault warning evident within the DIP The following DTC may also be evident - P310B00 Symptom 2636 - Fuel low pressure regulation (Figure 1). Technical background: IMPORTANT: Before following the instruction within the Measure section you must confirm the issue is evident in conjunction with the above symptoms, Erase all DTCs and attempt to reproduce the issue Should the issue be evident please refer to the instructions within the Measure section ensuring each step in followed to completion However Should the issue not be evident the operative must open a new DISS query or respond via the open DISS query and await feedback before conducting any further work

Customer statement / workshop findings: - Coolant leaking from the mechanical coolant pump And/or - Low coolant level warning displayed Technical background: The operative MUST ensure the instructions within the Measure section are followed, the instructions differ slightly depending on the part number of the mechanical coolant pump (B or C suffix).

Customer statement / workshop findings: Knocking noise from the underside of the vehicle (front) when driving on uneven road surfaces Workshop findings: Front trailing arm bush found damaged/leaking as shown in Figures 1 and 2 Technical background: If the customer complaint and symptoms are as described - Refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: Warning on the Driver Instrument Panel (DIP) - Oil pressure too low DTCs relating to oil pressure may also be stored within the Master ECU. Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU). Measure: VERY IMPORTANT: Prior to conducting the onward instructions, the following symptoms MUST be evident - Warning on Driver Instrument Panel (DIP) Oil pressure too low And/or - Diagnostic Trouble Codes (DTC) P052400: Engine Oil Pressure Too Low and/or P15AA00: Engine oil pressure - Lower limit not reached stored in the Master Engine Control Unit (ECU) Should any of the afore mentioned not be evident and the symptoms cannot be reproduced No further action should be taken unless the issue can be reproduced or demonstrated by the customer In the event the symptom/s are evident please conduct the onward Diagnosis Instructions

Customer statement / workshop findings: - Air conditioning not cooling and/or low refrigerant gas - DTC B10ABF0: Refrigerant pressure lower limit not reached may also be logged in diagnostic address 08 Technical background: In the event the issue is as described the operative should refer to the instructions within the Measure section of this TPI to assist in diagnosing the reported issue Before conducting the instructions within the Measure section the operative MUST refer to Rep.Gr 87 - Refrigeration system Bentley Motors Limited would like to stress that tracer additives have not been approved for use in our refrigeration systems. Tracer additives must not be used under any circumstances, failure to comply will invalidate warranty on all refrigeration system components

Customer statement / workshop findings: - Engine cooling system overheating And/or - Coolant loss And/or - Warning light in Drivers Information Panel (DIP) The following DTCs may also be evident within 0001 and/or 0011 - P2B6500 and/or P2B8600.

Customer statement / workshop findings: Customer complains of poor quality music output from the shaker speaker due to a rattling noise/sound distortion. Technical background: There have been instances where shaker speakers have been changed under warranty for the complaint of sound distortion, yet when tested by Bentley motors and the supplier, no fault could be found with the returned unit. Measure: To ascertain the difference between distortion or a rattle emanating from a loose/surrounding component Or The shaker speaker itself is incorrectly secured and/or at fault please conduct the following steps before replacing any components

Technical background: The intake valve springs (16) and outlet valve springs (16) located within the cylinder heads of Bank 1 and 2 require replacing. The replacement of all valve springs is required due to an issue which was discovered during a routine quality inspection. Remedy: The replacement of all intake valve springs and all outlet valve springs (Bank 1 and Bank 2) is required

Customer statement / workshop findings: Emission control system warning light illuminated within the DIP (Figure 1). Workshop findings: DTC P245000 - EVAP System Switching Valve "A" Performance/Stuck Open - With symptom code 11952 Technical background: Refer to the Measure section of this TPI

Customer statement / workshop findings: Air suspension warning light within the DIP Workshop findings: One or a combination of the DTCs shown below are evident within address 74 - P089200 - Symptom Code 3145792 - TCM Power Relay Sense Circuit Intermittent (Level Control Valves Open Circuit) - C103B13 - 3145909 - Solenoid for level control system Open circuit - C104707 - 3211279 - Level control valves mechanical malfunction Technical background: Refer to the Measure section of this TPI.

Technical background: The intake valve springs (16) and outlet valve springs (16) located within the cylinder heads of Bank 1 and 2 require replacing The replacement of all valve springs is required due to an issue which was discovered during a routine quality inspection. Remedy: The replacement of all intake valve springs and all outlet valve springs (Bank 1 and Bank 2) is required.

Customer statement / workshop findings: - Emission control warning within the DIP And/or - Whistling noise(s) from the Inlet manifold Workshop findings: Oil leak between the oil separator tank and the Bank 1 breather line connection (Figure 1) NOTE: Oil leak detection spray is evident within Figure1, the use of detection spray in the example shown highlights the location of the leak. Measure: 1) Referring to Rep.Gr 17 - Gain access to the oil separator tank 2) Referring to Figure 2 - Replace the following parts and all associated parts as detailed within the applicable Rep.Gr and the ETKA parts catalogue

intake valve springs (16) and outlet valve springs (16) located within the cylinder heads of Bank 1 and 2 require replacing The replacement of all valve springs is required due to an issue which was discovered during a routine quality inspection VERY IMPORTANT: Before continuing with the onward instructions the operative should confirm if the symptoms within TPI 2064776/- are applicable In the event the symptoms are applicable the operative MUST first conduct TPI 2064776/- to completion The operative MUST then raise a new Technical DISS query or respond via the already open DISS query and await feedback from Product Support before conducting any further work as further information will be requested back which may change the method of repair Remedy: The replacement of all intake valve springs and all outlet valve springs (Bank 1 and Bank 2) is required

Customer statement / workshop findings - Engine misfiring - Engine running rough (not refined) - Engine misfire DTCs evident - Engine management light illuminated within the DIP - Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) Measure VERY IMPORTANT: Before continuing with the onward instructions the operative should confirm if the following VIN applicable Service Campaign is listed within Elsa pro - EC24 - V8 Kovomo - New Continental GT/GTC and New Flying Spur - Valve spring replacement (SC21/41) Or - EC25 - V8 Kovomo - Bentayga - Valve spring replacement (SC21/42)

Customer statement / workshop findings: - Engine misfiring - Engine running rough (not refined) - Engine misfire DTCs evident - Engine management light illuminated within the DIP - Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) IMPORTANT: The symptoms described are typically evident during early life stages of vehicle use (between 100Km and 250Km) Technical background Refer to the Measure section of this TPI in the event the symptoms are as described

Technical background: The intake valve springs (16) and outlet valve springs (16) located within the cylinder heads of Bank 1 and 2 require replacing The replacement of all valve springs is required due to an issue which was discovered during a routine quality inspection Remedy: The replacement of all intake valve springs and all outlet valve springs (Bank 1 and Bank 2) is required

Customer statement / workshop findings: The crosslink and audio to car functions of the Rear Seat Entertainment screens are not working to specification (icons greyed out) a message is also displayed advising the feature(s) are not available when the icons are pressed Refer to the examples shown in Figures 1,2 and 3. Technical background: The new Rear Seat Entertainment system is being continually improved by Bentley Motors Some features are temporarily unavailable including the crosslink and audio to car these features will be available as an Over The Air update. No workshop visit is required once the updates are available.

Customer statement - MIL light displayed - Engine not refined when running Workshop findings The two most common DTCs are as follows: - P032700 - Knock sensor 2 Circuit Low input - address 01 (Engine control module 1) - P033200 - Knock sensor 1 Circuit Low input - address 01 (Engine control module 1) Please note: The DTCs listed are the two most common DTCs (seen to date) although other DTCs may be evident depending on the failure mode (including the boost control solenoid and crankcase ventilation heater DTCs)

Customer statement / workshop findings: Torque values for ancillary components (used during engine replacement) are not currently available within the Repair manual. The affected components and torque values are as listed within the Technical background section of this TPI. Measure: Refer to the Technical background section

Customer statement / workshop findings: - Knocking noise from the underside of the vehicle (front and/or rear) when driving on uneven road surfaces - DTC C1298F1 (Suspension stabilization actuator Regulation not possible) evident within diagnostic address D4 and/or D5 - Bentley Dynamic ride fault evident within the DIP Technical background: In the event the symptoms are as described, Refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: The following issues could be evident during PDI or found whilst in service - Electronic Parking Brake (EPB) found not operating to specification - EPB may not hold the car effectively - Parking brake components showing signs of wear - Parking brake warning light may also be evident within the DIP (See example shown in Figure 1). NOTE: The following DTCs may also be evident - C10E1F2: - 158720 - Parking brake motors Positions not plausible - C10BDF1: - 160768 - Right parking brake motor Upper travel limit exceeded And/or - C10BCF1: - 161024 - Left parking brake motor Upper travel limit exceeded Technical background: The issues described can be evident due to the car being driven in Transport mode with the EPB applied during the Transit process Or In some cases similar symptoms may be seen whilst in service

Customer statement / workshop findings; - The engine management light is on. Workshop findings: The customer statement can be reproduced. Either of the following DTCs are stored in address 01 Engine Control Module 1 or address 11 Engine Control Module 2 - P257900: Turbocharger Speed Sensor A - Circuit Range/Performance Or - P259400: Turbocharger Speed Sensor B - Circuit Range/Performance Or - P259500: Turbocharger Speed Sensor B - Circuit low

Customer statement / workshop findings: Knock/clunking noise heard from the rear of the vehicle when changing direction at low speed Technical background: Ensure the fault is as described within the Customer statement Refer to the videos on the Bentley Hub referencing TPI 2064477/- In the event the knock/clunk is as shown within the videos the instructions within the Measure section should be followed noting the following: Video number 4 for TPI 2064477/- (on the Bentley Hub) specifically relates to the symptom described within step 3 of the Measure section (Heatshield in contact with the rear differential)

at low speed Technical background: Ensure the fault is as described within the Customer statement Refer to the videos on the Bentley Hub referencing TPI 2064477/- In the event the knock/clunk is as shown within the videos the instructions within the Measure section should be followed noting the following: Video number 4 for TPI 2064477/- (on the Bentley Hub) specifically relates to the symptom described within step 3 of the Measure section (Heatshield in contact with the rear differential)

Technical background: Verify that the customer complaint matches the sound file within the Bentley Hub - Reference TPI Transaction number 2064791/- The noise present in the sound file can be caused by worn anti roll bar bushes, the noise can appear when driving over an uneven road surface or during a large suspension input for example: -Speed humps or potholes If the customer complaint occurs and the noise can be clearly assigned to the noise within the sound file - Refer to the instructions within the Measure section of this TPI

evident -Engine management light illuminated within the DIP -Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) IMPORTANT: The symptoms described are typically evident during early life stages of vehicle use (between 100Km and 250Km)

activation/ deactivation solenoid fixings -Or Fuel rail fixings -Or Fixings for the vacuum system assembly Technical background: Shows oil leaked which had leaked from the tell tale hole at the top of the fixing. Upgraded fixings prevent oil leaks from the tell hole.

Customer statement: Parking brake warning light evident within the DIP (See example shown in Figure 1) Workshop findings: C10BCF6 - 160000 - Left parking brake motor Engine speed implausible OR C12E2F2 - 159744 - Right parking brake motor Engine speed implausible.

Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring.

Technical background Ensure the fault is as described within the Customer statement. Refer to the videos on the Bentley Hub referencing TPI2064477/-. In the event the knock/clunk is as shown within the videos the instructions within the Measure section should be followed.

Customer Statement: Emission control system warning light illuminated within the DIP. Workshop findings: DTC P245000 - EVAP System Switching Valve A Performance/Stuck Open - With symptom code 11952 Technical Background: Refer to the Measure section of this TPI.

Customer statement / workshop findings: Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) in conjunction with DTC - P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow - logged within one or both engine control modules. Technical background: Should DTC P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow be evident (static or intermittent) within one or both Engine control modules please refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings Workshop findings: Buzzing noise heard at idle from the sump area when the vehicle is elevated on a workshop ramp. The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances. Technical background: A buzzing noise can be generated by the oil pump when the engine is running at idle. Measure: Test a comparable vehicle with the same Engine derivative. If the same noise is apparent on the comparable vehicle and no oil pressure warnings or relevant DTCs are stored then the noise can be considered a characteristic of the vehicle and no further action should be taken.

Customer statement / workshop findings: The Start/Stop system functions with the drivers seat belt not fastened although the Owners handbook states that the drivers seat belt must be fastened for the Start/Stop system to function. Technical background On all 202 0model year vehicles specified with a V8 engine, the Start/Stop system will function with the drivers seat belt not fastened although the Owners handbook states the drivers seat belt must be fastened for the Start/Stop system to work, the system in this scenario is functioning correctly. Due to a change to one of the system inhibits, the 2021 model year Owners handbooks will be updated to confirm the Start/Stop system will work with the seat belt unfastened.

Customer statement / workshop findings: Suspension warning lamp illuminated on Driver Instrument Panel (DIP) appeared when changing the Drive dynamics mode using the rotary switch on the front centre console: For example - When changing from Bentley to Sport mode. Diagnostic Trouble Codes (DTCs) C134911 and/or C134B11 Valve 1 for auxiliary volume 2Short circuit to Ground (GND) evident within address 0074. Technical background: The issue is a result of the incorrect operation of the front air spring damper (right and/or left) between the internal chambers 1 and 2.

Customer statement / workshop findings Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services. Technical background: In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified running-in periods consume more oil during the running-in period, and the oil consumption will stabilize after the running-in period. Refer to the Owners Manual for specific running-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Certain driving conditions may negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods

findings: Warning lamp illuminated on Driver Instrument Panel (DIP) Drive system fault. Contact your Bentley dealer displayed on DIP. One or more of the following Diagnostic Trouble Codes (DTCs) stored within Engine Control Modules (ECMs) 1 or 2 (Depending on model type) P04A000: Exhaust Pressure Control Valve P04A000 / P047500: Exhaust Pressure Control Valve A P14AB00: Exhaust door control unit mechanical malfunction P049F00: Exhaust Pressure Control Valve "B

the rear of the cabin when sitting in the rear seats Technical background: The noise can be heard when the engine is at operating temperature, after a drive cycle or an extended idle period, the noise is most evident with the armrest lowered with all electrical consumers switched off. The ticking noise occurs when the purge system is in operation, the vibrations emitted from the purge valve are then amplified through the fuel pipes to the rear of the vehicle. This is normal operation and no further investigation work is required as the vehicle is operating to specification.

statement: Engine warning light and max engine speed 4000 rpm warning evident within the DIP during acceleration - Warning on DIP first appears when accelerating (During boost) Workshop findings: DTC P029900 evident within the engine control unit/s In the event the afore mentioned symptoms are evident the operative should refer to the onward instructions

Workshop findings: The irregular knocking noises can be assigned to the front of the engine. There are no further complaints (such as poor engine or engine cooling system performance, event entries, etc.)

Customer statement: Drive system fault active on DIP. Workshop findings: Various and/or numerous Transmission control module DTCs logged. Technical background: Loose pins within the transmission link harness to the Mechatronic unit for dual clutch gearbox -J743- connections can lead to various and/or numerous Transmission control module DTCs being logged. Carry out the checks within the Measure section of this TPI noting the following: The steps within the Measure section are applicable to vehicles specified with or without the Otto Particulate Filter (OPF) also referred to as the Gasoline Particulate Filter (GPF) NOTE: OPF/GPF fitment is Region specific. Should any issues be evident and the vehicle is specified with (OPF/GPF) The operative should check to confirm if EB89 (SC21/08 is required) and conduct if applicable. In the event that EB89 (SC21/08)is not required and the symptoms described within this TPI are evident the onward instructions should be followed.

Technical background: We have observed instances where the caps have been difficult to remove once fitted, the issue is caused by corrosion. The valve stem itself is made from aluminium and the accessory valve caps are chromium plated brass, it is possible under certain environmental conditions, particularly winter road salt, for corrosion to take place between these dissimilar metals. Measure: The solution is to apply a thin smear of silicon-based grease, such as Dow Corning high vacuum grease, to the external threads of the valve stem prior to fitting the accessory valve cap. Grease should be applied any time the cap is removed and grease is not evident

Customer statement / workshop findings: Engine oil level requires top up between services Technical background: The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Customer statement / workshop findings: HVAC operation issues and HVAC motor defect (DTCs) evident within address 08 Climatronic control unit, the DTCs can be static or sporadic (Intermittent) The Event memory entries (DTCs) shown within the Header data of this TPI are included as examples Technical background: The HVAC motors can become defective causing HVAC operational issues IMPORTANT: The following instructions should only be carried out on receipt of a valid customer complaint Or The operative is conducting EB28 or EB29 and issues are evident

Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.

Customer Statement: Airflow from the organ stops (air regulators) is not functioning correctly; vents may be stuck, broken, or showing incorrect operation.

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP)

Customer statement / workshop findings: Lane Assist and / or Traffic Assist are not functional DTC - B17B801 - Steering Wheel Touch Recognition Control Module evident within address 0019 And/or DTC B17B804 - Steering Wheel Touch Recognition Control Module electrical error - evident within address 0019 And/or DTC U112300 with symptom Code 1123220 within address 00A5

Technical background If an issue is suspected for one of the control modules listed below: Onboard supply control unit (J519) Convenience system central control unit (J393) Data bus diagnostics interface (J533) Control unit 1 for Information Electronics (J794) Control unit in dash panel insert (J285) Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query.

Headlamp switch not working / not illuminated when the ignition is switched on (following an ignition switch off) And/or Yellow warning light/message within DIP (Adaptive lighting fault) And / or Loss of rear fog light activation And / or Loss of all-weather lighting mode activation And / or Headlamps will default to dipped beam (however, high beam activation will still be possible manually)

An Over The Air Update (OTA) could be required for both of the Bring Your Own Content (BYOC) screens. The update includes the following: Fixes for casting issues across multiple apps Expanded app support Chromium browser upgrade to v114 Improved OTA download speed in China Fixes for minor bugs from previous maintenance phase Patches addressing identified cybersecurity vulnerabilities.

Customer statement / workshop findings: 12 volt battery flat or unserviceable

Customer statement / workshop findings: 12 volt battery flat or unserviceable

Condition: 12 volt battery flat or unserviceable

Customer Statement: Airflow from the organ stops (air regulators) is not functioning correctly; vents may be stuck, broken, or showing incorrect operation.

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP)

Condition: Lane Assist and / or Traffic Assist are not functional DTC - B17B801 - Steering Wheel Touch Recognition Control Module evident within address 0019 And/or DTC B17B804 - Steering Wheel Touch Recognition Control Module electrical error - evident within address 0019 And/or DTC U112300 with symptom Code 1123220 within address 00A5

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP)

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP)

Condition: Lane Assist and / or Traffic Assist are not functional DTC - B17B801 - Steering Wheel Touch Recognition Control Module evident within address 0019 And/or DTC B17B804 - Steering Wheel Touch Recognition Control Module electrical error - evident within address 0019 And/or DTC U112300 with symptom Code 1123220 within address 00A5

Customer statement: Headlamp switch not working / not illuminated when the ignition is switched on (following an ignition switch off) And/or Yellow warning light/message within DIP (Adaptive lighting fault) And / or Loss of rear fog light activation And / or Loss of all-weather lighting mode activation And / or Headlamps will default to dipped beam (however, high beam activation will still be possible manually)

Customer statement / workshop findings: Keyless entry system (KESSY) function is disabled when the vehicle is parked for a short duration of time Technical background: The reported symptom is due to the Battery management shut off stages being too early due to the battery size being incorrectly entered on replacement

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP) Workshop findings: DTC P0B2500 - Hybrid/EV Battery "A" Voltage low is stored within address 21- Battery Energy Control Module 2 Technical background: Possible internal fault with the super capacitor

Customer statement: Night vision warning lamp (Figure 1) is evident with the Drivers Information Panel (DIP). Workshop findings: DTC - B2000F2: Faulty control module (Symptom code 4102) evident within address 0084 - Night vision control module.

Customer statement / workshop findings Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP) Workshop findings: DTC P0B2500 - Hybrid/EV Battery "A" Voltage low is stored within address 21- Battery Energy Control Module 2 Technical background: Possible internal fault with the super capacitor

Customer statement: Headlamp switch not working / not illuminated when the ignition is switched on (following an ignition switch off) And/or Yellow warning light/message within DIP (Adaptive lighting fault) And / or Loss of rear fog light activation And / or Loss of all-weather lighting mode activation And / or Headlamps will default to dipped beam (however, high beam activation will still be possible manually)

Workshop findings The following DTCs could also be evident within diagnostic address 0046 and/or 00BB and/or 00BC B131DF5: alarm system siren supply voltage lower limit value less than B131D29: sirens / alarm horn for anti-theft warning system Range/Performance B131D29: anti-theft alarm system siren / alarm horn signal, not valid

Customer statement: Tyre pressure sensor: low battery warning is evident with the Drivers Information Panel (DIP). Workshop findings: One or a combination of the following DTCs may also be evident: - C105016 Left Front Tyre Pressure Monitoring Sensor Voltage too low - C105116 - Right Front Tyre Pressure Monitoring Sensor Voltage too low - C105216 - Left Rear Tyre Pressure Monitoring Sensor Voltage too low - C105316 - Right Rear Tyre Pressure Monitoring Sensor Voltage too low.

Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section.

Customer statement: Unintended sounding of the alarm siren following activation of the ignition Or Unintended sounding of the alarm siren whilst the vehicle is left standing. Workshop findings: - B131DF5: alarm system siren supply voltage lower limit value less than - B131D29: sirens / alarm horn for anti-theft warning system Range/Performance - B131D29: anti-theft alarm system siren / alarm horn signal, not valid

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP). Workshop findings: DTC P0B2500 - Hybrid/EV Battery "A" Voltage low is stored within address 21- Battery Energy Control Module 2.

Customer statement / workshop findings: - Rear Steering Fault warning present within the DIP. Workshop findings: The following DTCs could be evident within diagnostic address 00CB - Rear Axle Steering control module - DTC B200096 and/or P060700 - The rear wheels may also be tracking incorrectly. Technical background: In the event the symptom described with the Customer statement/workshop findings section is evident the operative should conduct the instructions within the Measure section.

Customer statement / workshop findings: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP) Workshop findings: DTC P0B2500 - Hybrid/EV Battery "A" Voltage low is stored within address 21- Battery Energy Control Module 2.

Customer statement / workshop findings Rear side window blind(s) do not operate - Rear blind/s do not operate following a CAN bus sleep - Rear blind/s do not operate if the switch operation is a prolonged hold instead of a Press and release operation - Rear blind/s do not operate following the loss of control module basic settings - Rear blind/s will also not operate if the Child Lock is on - Rear blind/s will cease to operate if there are repeated operations of the blind sufficient to trigger a failsafe mode (usually between 10 to 15 operations in a very short period) - As instructed within the owners handbook, the rear blind/s will not operate if the rear window is in the lowered position - The blind will also not operate in extreme cold temperature for example -10 degrees Celsius or 14 degrees, Fahrenheit.

Customer statement / workshop findings: Keyless entry does not work Workshop findings: Front outside door handle(s) touch sensor open circuit DTC(s) present within address 0046.

Customer statement: Lane Assist and/or Traffic Assist are not functional Workshop findings: - DTC - B17B801 - Steering Wheel Touch Recognition Control Module evident within address 0019 And/or - DTC B17B804 - Steering Wheel Touch Recognition Control Module electrical error - evident within address 0019 And/or - DTC U112300 with symptom Code 1123220 within address 00A5.

Customer statement / workshop findings: Technical DISS queries with extended downtime can be caused by incorrect diagnosis and testing of the vehicles electrical circuits In a small number of isolated cases basic electrical faults were found to be overlooked. Technical background: The information within this TPI has been generated to make retailers aware of two specific videos (Figure 1) Advanced Vehicle Electrics - Measurements of Circuits Video - Voltage drop testing - Voltage drop testing using the VAS 6356 scope Advanced Vehicle Electrics - Actuators & Voltage Supply Diagnosis - Terminal drag testing

Customer Statement: Unintended sounding of the alarm siren following activation of the ignition Or Unintended sounding of the alarm siren whilst the vehicle is left standing

Statement: -Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP)

one of the control modules listed below: Onboard supply control unit (J519) Convenience system central control unit (J393) Data bus diagnostics interface (J533) Control unit 1 for Information Electronics (J794) Control unit in dash panel insert (J285) Emergency call module control unit (J949)

Customer statement: Keyless entry does not work. Workshop findings: Front Outside Door Handle(s) Touch Sensor open circuit DTCs present within address 0046. NOTE: The afore mentioned issue does not affect the ability to lock/unlock the vehicle manually by inserting the key into either of the front door locks or by using the lock/unlock buttons on the ignition key fob.

If the charging socket or charger lead are wet when the charger is connected this can cause corrosion on the contacts.

Statement: -(Bentley dynamic ride system: fault) displayed within the Drivers Instrument Panel (DIP)

Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section

Customer statement: Incorrect rear seatbelt buckle status shown within the DIP Workshop findings Although there is no occupant evident within the rear seats (2nd row) the rear seat is shown as occupied (Figure 1). Technical background: There is no specific DTC evident for the scenario described. The issue described is evident as the rear seat belt buckles are not resistor coded The system uses a non-resistor coded buckle strategy (zero-infinity or open-closed buckle) for the rear seats. In correct operation, a fastened seatbelt is open circuit and an un-fastened seatbelt is closed circuit If harness damage is present or an electrical connector joint is not properly engaged, an unintended open circuit occurs. This will give an incorrect buckle status reading within the DIP The advice within this TPI should be referred to first before conducting any further diagnosis or disassembly of the vehicles interior Previous assembly/disassembly may have caused an unintentional open circuit when operatives have been working on or around the rear seat belt assemblies.

Customer statement: Bentley dynamic ride system: fault displayed within the Drivers Instrument Panel (DIP) Workshop findings: DTC P0B2500: Hybrid/EV Battery "A" Voltage low' stored within address 21-Battery Energy Control Module 2 Technical background: Possible internal fault with super capacitor - In the event that DTC P0B2500 is evident the operative must follow the steps within the Measure section to completion

Technical background: If an issue is suspected for one of the control modules listed below: - Onboard supply control unit (J519) - Convenience system central control unit (J393) - Data bus diagnostics interface (J533) - Control unit 1 for Information Electronics (J794) - Control unit in dash panel insert (J285) - Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query. The donor of parts should only be used as a temporary test VERY IMPORTANT: The ODIS replace routine MUST NOT be carried out under any circumstances.

intermittently -During failure, the ignition function returns after 15 minutes, the vehicle then operates to specification

Customer statement / workshop findings: Bentley dynamic ride system: fault displayed within the Drivers Instrument Panel (DIP) Workshop findings: DTC P0B2500: Hybrid/EV Battery "A" Voltage low' stored within address 21-Battery Energy Control Module 2 Technical background: Possible internal fault with super capacitor, refer to the Measure section of this TPI

Customer statement / workshop findings: Warning lamp illuminated within the Driver Instrument Panel (DIP) -Drive system fault. Contact your Bentley dealer- Technical background: The root cause of Exhaust Flap Control Unit malfunction is electrical shorting of the commutator segments, this is caused by an accumulation of Sludge within the exhaust flap control unit DTCs are stored when the respective Control Unit does not move through its full range of motion.

-Headlamp switch not working/not illuminated when the ignition is switched on (following and ignition switch off) and/or -Yellow warning light/message within DIP (Adaptive Lighting Fault) and/or -Loss of rear fog light activation and/or -Loss of all-weather lighting mode activation and/or -Headlamps will default to dipped beam

Statement: -One or a combination of the following are evident with the Bring Your Own Content Table (BYOC) -The tablet will not electrically connect or operate -The tablet will connect and operate

-Headlamp switch not working/not illuminated when the ignition is switched on (following an ignition switch off) and/or -Yellow warning light/message within DIP (Adaptive lighting fault) and/or -Loss of rear fog light activation and/or -Loss of all-weather lightin mode activation and/or -Headlamps will default to dipped beam (however, high beam activation will still be possible manually

Address: 0015 System name: 15 - Airbag Control Module -B130474: Left front seat belt tensioner control module actuator deviated -B130574: Right front seat belt tensioner control module actuator deviated -The DTCs can be evident if the occupant uses a dummy seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings

Statement: -Bentley Dynamic Ride System: fault displayed within the Drivers Instrument Panel (DIP) Technical Background: -Possible internal fault with super capacitor. refer to the measure section of this TPI

If the charging socket or charger lead are wet when the charger is connected this can cause corrosion on the contacts.

Findings: -U061F00: Lost communication with exhaust gas temperature sensor bank 1 sensor 1 -U062100: Lost communication with exhaust gas temperature sensor bank 1 sensor 1

-Keyless door entry does not work

-Headlamp switch not working/not illuminated when the ignition is switched on (following an ignition switch off) and/or -Yellow warning light/message within DIP (Adaptive lighting fault) and/or -Loss of rear fog light activation and/or -Loss of all-weather lighting mode activation and/or -Headlamps will default to dipped beam (however, high beam activation will still be possible manually)

-Headlamp switch -Inoperative/Not Illuminated Workshop findings: -DTC U110B00 within 09-Central Electrics (BCM1) as shown in figure 1

Customer Statement: -The following DTCs could also be evident within the diagnostic address 0046 and/or 00BB and/or 00BC -B131DF5: alarm system siren supply voltage lower limit value less than -B131D29: sirens/alarm horn for anti-theft warning system range/performance -B131D29: anti-theft alarm system siren/alarm horn signal, not valid

parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the measure of this section of this TPI.

Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.

Background: -The condition will not occur when the ignition is on or whilst the vehicle is being driven -The condition only occurs as the headlamp switch goes into a "Sleep" state after the ignition is switched off -The condition is evident to the driver when the ignition is next switched on

Customer Statement: -Blind spot monitors (wing mirror illuminations) are not functional in conjunction with sporadic Bentley assist warnings present in the DIP. Workshop findings: Master or slave rear radars are not fitted correctly (unclipped or poorly installed) Diagnostic Trouble Code (DTC) C1114F3 - Lane change assistance control module restricted view, logged with address 003C or 00CF

Customer statement: Keyless entry does not work Workshop findings: Front Outside Door Handle(s) Touch Sensor open circuit DTCs present within address 0046 NOTE: The afore mentioned issue does not affect the ability to lock/unlock the vehicle manually by inserting the key into either of the front door locks or by using the lock/unlock buttons on the ignition key fob. Technical background: Refer to the Measure section of this TPI

Customer statement / workshop findings: Bentley dynamic ride system: fault displayed within the Drivers Instrument Panel (DIP) Workshop findings: DTC P0B2500: Hybrid/EV Battery A Voltage low stored within address 21-Battery Energy Control Module 2 Technical background: Possible internal fault with super capacitor, refer to the Measure section of this TPI

Customer statement / workshop findings Customer statement: - Headlamp switch not working/not illuminated when the ignition is switched on (following an ignition switch off) And/or - Yellow warning light/message within DIP (Adaptive lighting fault) And/or - Loss of rear fog light activation And/or - Loss of all-weather lighting mode activation And/or - Headlamps will default to dipped beam (however, high beam activation will still be possible manually) Workshop findings: The following DTCs may also be evident within 0009 - Central Electrics control module U110B00 - Light switch no communication And/or B126A29 - Light switch signal not reliable And/or U1122300 - Fault value received by data bus Technical background - The condition will not occur when the ignition is on or whilst the vehicle is being driven - The condition only occurs as the headlamp switch goes into a Sleep state after the ignition is switched off - The condition is evident to the driver when the ignition is next switched on In the event the afore mentioned symptoms are evident please carry out the instructions within the Measure section

Customer statement: Lane Assist and/or Traffic Assist are not functional Workshop findings: DTC - B17B801 - Steering Wheel Touch Recognition Control Module evident within address 0019 And/or DTC B17B804 - Steering Wheel Touch Recognition Control Module electrical error - evident within address 0019 And/or DTC U112300 with symptom Code 1123220 within address 00A5 Technical background: Revision history TPI 2063855/4 - Additional request to replace the control module (as Figure 1) in conjunction with the steering wheel

Condition: Customer statement: Headlamp low beam not functioning and/or warning within the DIP Workshop findings: DTCs C119813 Low beam light bulb open circuit active/static and/or C1198FA Low beam light bulb short circuit active/static logged within diagnostic address D6 (light control left) and/or D7 (light control right) Technical Background: The DTCs once triggered are unable to be cleared, with the DTCs logged the Headlamp low beam will not operate. In the event the symptoms are as described, conduct the instructions within the Measure section to completion noting the following: - The update to address D6 Must be done first followed by the update to address D7 - Regardless of the DTC which is evident or the address in which the DTC/DTCs are evident, both SVM codes MUST be applied IMPORTANT: There are separate SVM codes for each diagnostic address D6 (light control left) - 371D6HHZDC (MUST BE APPLIED FIRST) D7 (light control right) - 371D7HKZDC (MUST BE APPLIED SECOND)

Customer statement: Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) Workshop findings: U061F00: Lost Communication With Exhaust Gas Temperature Sensor Bank 1 Sensor 1 U062100: Lost Communication With Exhaust Gas Temperature Sensor Bank 2 Sensor 1 After further investigation the wiring harness leading to the Exhaust gas temperature sensor (Bank 1 and/or Bank 2) runs close to the sub-frame may rub/contact the edge of the bracket inside of the wheel arch cover/liner See the examples shown in Figure 1 (Chaffed/damaged wiring Bank 1) And Figure 2 (Broken/damaged wiring Bank 2) Technical background: Technical product information V8 Kovomo - Emission control warning illuminated within the DIP - Exhaust Gas Temperature Sensor DTC's evident Transaction No.: 2065698/1

Customer statement / workshop findings: - Warnings within the DIP for the rear steering system (Figure 1) Workshop findings: - DTC P060700 evident within diagnostic address 00CB - Rear Axle Steering control module Technical background: In the event the issue is as described the operative should conduct the instructions within the Measure section of this TPI

Customer statement / workshop findings: - PDC system not working or PDC system false detection - Warning evident within the DIP (Figure 1). Workshop findings: Parking aid sensor Range/Performance DTCs evident within numerous control units Technical background: Refer to the Measure section of this TPI.

Customer statement / workshop findingsL Diagnostic Trouble Codes (DTCs) evident in Address: 0015 System name: 15 - Airbag Control Module B130474: Left front seat belt tensioner control module Actuator deviated B130574: Right front seat belt tensioner control module Actuator deviated The DTCs can be evident if the occupant uses a dummy seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings. Technical background: Dummy seat belt buckles of any description MUST NOT be used under any circumstances, Figure 1 shows an example of a dummy seat belt buckle

Customer statement / workshop findings: When using a public charging unit to charge the high voltage battery, charging starts and is then interrupted/stops Workshop findings The following DTC is also evident: P33E800: Charge socket A, charge connector lock mechanical malfunction passive/sporadic. Measure: 1) Referring to Rep.Gr 93 - Carry out an Inspection and classification of the Hybrid battery unit AX1 VERY IMPORTANT: In the event that the classification result of the battery is Normal the operative should conduct the remaining steps of this TPI from step 2 However If the classification result of the battery is either Danger or Warning then move the car to the quarantine area and raise a DISS immediately, the operative MUST NOT continue with any other work unless instructed via the open DISS query 2) Check the operation of the charging system using the customers and the retailers own charging equipment 3) Run a full diagnostic log and check if the DTC within the Technical background section are evident.

Customer statement / workshop findings: Unintended sounding of the alarm siren following activation of the ignition Or Unintended sounding of the alarm siren whilst the vehicle is left standing Workshop findings. The following DTCs could also be evident within diagnostic address 0046 and/or 00BB and/or 00BC - B131DF5: alarm system siren supply voltage lower limit value less than - B131D29: sirens / alarm horn for anti-theft warning system Range/Performance - B131D29: anti-theft alarm system siren / alarm horn signal, not valid Technical background: In the event the symptom(s) described are evident, please refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: Bentley dynamic ride system fault warning displayed within the DIP Workshop findings: DTC P0B2600 (Hybrid Battery A Voltage High) with Symptom Code 28672. Measure: 1) Refer to Rep.Gr 27 - Replace the Super capacitor 2) Once the work is complete - Raise a non technical DISS query confirming the issue is now resolved

Customer statement / workshop findings: Bentley Home Charging Unit - Unable to recollect Personal Identification Number (PIN). Unable to charge High Voltage Battery with Bentley Home Charging Unit. Technical background: The Bentley Home Charging Unit can be protected from unauthorised use by creating a four-digit PIN. If the PIN authorisation function is activated it has to be entered in the Home Charging Unit before it is used to charge the High Voltage Battery. If a Customer forgets the assigned PIN it will not be possible to unlock the Bentley Home Charging Unit. Follow the steps within the 'Measure' section to reset the PIN.

name: 15 - Airbag Control Module B130474: Left front seat belt tensioner control module Actuator deviated B130574: Right front seat belt tensioner control module Actuator deviated The DTCs can be evident if the occupant uses a dummy seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings Technical Background: Dummy seat belt buckles of any description MUST NOT be used under any circumstances, Figure 1 shows an example of a dummy seat belt buckle - B130474 and/or B130574

Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

light control unit (Diagnostic address D6) and/or the right light control unit (Diagnostic address D7) There are numerous static and intermittent DTCs which maybe evident within the previously mentioned control units, ensure all steps within the Measure section are strictly adhered to New Flying Spur (20 - 22 M/Y) and Bentayga (21 - 22 M/Y). In the event that DTCs C119813 Low beam light bulb open circuit or C1198FA Low beam light bulb short circuit are evident in D6 and/or D7. Please refer to and conduct the instructions within the following TPIs New Flying spur - TPI 2063777/- Bentayga applicable to 21 and 22 M/Y only - 2064497/-. For any other issues please refer to the instructions within the Measure section of this TPI.

Customer statement: Blind spot monitors (Wing mirror illuminations) are not functional in conjunction with sporadic Bentley assist warnings present in the DIP. Workshop findings: Master or slave rear radars are not fitted correctly (unclipped or poorly installed). Diagnostic Trouble Code (DTC) C1114F3 - Lane change assistance control module restricted view, logged with address 003C or 00CF. Technical background: As per the Workshop findings section, the operative should review the Theory of operation chapter for the Rear radar. Production change: All VINs post SCBCX13S4MC086559 are to specification.

Condition: Diagnostic Trouble Codes (DTCs) evident in Address: 0015 System name: 15 - Airbag Control Module B130474: Left front seat belt tensioner control module Actuator deviated B130574: Right front seat belt tensioner control module Actuator deviated The DTCs can be evident if the occupant uses a dummy seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings Technical Background: Dummy seat belt buckles of any description MUST NOT be used under any circumstances, Figure 1 shows an example of a dummy seat belt buckle.

for example: - The boot does not open or close as expected Technical background: NOTE: The operative MUST submit the following information to a new DISS query or an existing query relating to boot operational issues - Completed check list - Images of the vehicle condition - In particular the boot area (Ensure license plate and VIN details are not visible) - Video of the failure NOTE: Please capture the rear of the vehicle for at least one open/close operation (when possible) before zooming or moving in closer to the issue, the video MUST be recorded in a quiet environment - Battery health - Print out of the results

Customer statement: Buzzing noise may be evident from the left and/or right headlamp Workshop findings The following DTCs may also be evident in 00D6 Light control left 2 (Matrix beam) and/or 00D7 Light control right 2 (Matrix beam) C119C01 Fan for headlamp electrical error C119D01 Fan 2 for headlamp electrical error Technical background: Wiring harness routed incorrectly within the headlamp module at the rear of the headlamp, the noise and DTCs are evident due to the harness contacting the headlamp cooling fan

Customer statement: Headlamp low beam not functioning and/or warning within the DIP Workshop findings: DTCs C119813 Low beam light bulb open circuit active/static and/or C1198FA Low beam light bulb short circuit active/static logged within diagnostic address D6 (light control left) and/or D7 (light control right)

one of the control modules listed below: - Onboard supply control unit (J519) - Convenience system central control unit (J393) - Data bus diagnostics interface (J533) - Control unit 1 for Information Electronics (J794) - Control unit in dash panel insert (J285) - Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query.

Workshop findings: DTC - B2000F2: Faulty control module (Symptom code 4102) evident within address 0084 Night vision control module. Technical background: IMPORTANT: In the event that the issue is evident and the vehicle is post the VINs shown below, a DISS query must be raised ensuring the following is attached to the query. -Detailed description in which the issue occurred, for example -Driving on a quiet road with no traffic, conditions were wet, the road had no street lighting. -Clear photographs showing the condition of the night vision camera and night vision camera lens. -Current and up to date ODIS log. However, should the vehicle be prior to the VIN cut off, the operative MUST carry out the instructions within the Measure section of this TPI. New Flying Spur New Continental GT and New Continental GTC (all vehicles from SCBCD13S1KC071068 are to specification). Bentayga (all vehicles from SJAAL14V0KC025622 are to specification).

If the charging socket or charger lead are wet when the charger is connected this can cause corrosion on the contacts. Check for corrosion on the contact surfaces of both the charger socket and charger lead.

Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

Customer statement: Air suspension warning lamp illuminated within the Driver Instrument Panel (DIP) Workshop findings: Combination or multiple DTCs see the examples shown below of current known faults. Technical background: Broken, damaged, dislodged and disconnected air suspension air spring connectors have been evident result in open circuit DTCs

Customer statement / workshop findings: Refer to the Technical background section before considering the fitment of control modules from donor vehicles for test purposes Technical background: If an issue is suspected for one of the control modules listed below: - Onboard supply control unit (J519) - Convenience system central control unit (J393) - Data bus diagnostics interface (J533) - Control unit 1 for Information Electronics (J794) - Control unit in dash panel insert (J285) - Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query. The donor of parts should only be used as a temporary test VERY IMPORTANT: The ODIS replace routine MUST NOT be carried out under any circumstances

Customer statement / workshop findings: Outer demister panel (speaker grille) lifted / Incorrect flushness

Customer statement / workshop findings: The customer requests improved and/or newer navigation functionality, including access to the latest navigation maps and updated map content.

Customer statement / workshop findings: Windscreen cracked/damaged

Condition: One or a combination of the following issues are evident: Infotainment screen stuck on initialising Or Loading messages are visible at start up (within multiple tiles) Or Bentley Rotating Display (BRD) doesnt return to its previous state

Condition: Bentley Rotational Display (BRD) operational issues Mechanical malfunction DTC B140107 evident within 005F

Condition: Issue suspected with the Infotainment Main unit (5F / J794) - For example: MMI screen image flickers or goes blank No response to selection Audio cuts out

Customer statement / workshop findings: Bentley Rotational Display (BRD) clashing with the MMI switch pack during rotation.

Customer statement / workshop findings: Outer demister panel (speaker grille) lifted / Incorrect flushness.

An Over The Air Update (OTA) is required for both of the Bring Your Own Content (BYOC) screens The update addresses the following issues: Netflix browser compatibility issue Google Cast airserver certificate issues

Customer statement / workshop findings: Outer demister panel (speaker grille) lifted / Incorrect flushness.

Customer statement / workshop findings: One or a combination of the following symptoms are evident: Rear sunblind does not operate Rear sunblind is noisy during operation Rear sunblind operates sporadically Rear sunblind is detached on one side

Customer statement / workshop findings: One or a combination of the following symptoms are evident: Rear sunblind does not operate Rear sunblind is noisy during operation Rear sunblind operates sporadically Rear sunblind is detached on one side.

Customer statement / workshop findings: One or a combination of the following issues are evident: - Infotainment screen stuck on initialising Or - Loading messages are visible at start up (within multiple tiles) Or - Bentley Rotating Display (BRD) doesnt return to its previous state Technical background: Should the symptoms within the Customer statement/Workshop findings section be evident please conduct the instructions within the Measure section.

Customer statement / workshop findings: Various rotating display screen noise during operation.

Customer statement / workshop findings: - Bentley Rotational Display (BRD) operational issues - Mechanical malfunction DTC B140107 evident within 005F

Customer statement / workshop findings Infotainment screen 'Goes Red Fully or partially' within the MMI Screen.

Customer statement / workshop findings Upon start-up of the Home screen, loading messages can be seen in some or all of the tiles. Measure: A delay when loading tiles is normal, this is due to the amount of external data that is required to load each individual tile, including multiple pages of external data that can be associated with each individual tile.

Customer statement / workshop findings The rear screen sunblind is not operating to specification Or a combination of the following symptoms are evident - Rear sunblind does not operate - Rear sunblind is noisy during operation - Rear sunblind operates sporadically - Rear sunblind is detached on one side.

Statement: -Bentley Rotational Display (BRD) operational issues -Mechanical malfunction DTC B140107 evident within 005F

Customer Statement: -Various rotating display screen noise during operation

shaker speaker due to a rattling noise/sound distortion

dynamic ride system fault warning displayed within the DIP

Infotainment Main unit (5F / J794) - For example: MMI screen image flickers or goes blank No response to selection Audio cuts-out

Customer statement / workshop findings: Upon start-up of the Home screen, loading messages can be seen in some or all of the tiles.

Customer statement / workshop findings Upon start-up of the Infotainment system, the home screen appears to be stuck in the Initializing stage, when this scenario is evident a spinning wheel is visible.

shows (Component Protection Active). Diagnostic Trouble Code (DTC) U110100 Component Protection Active stored within 004E (Display/Control head HR) and/or 005E (Display/Control Head LH).

within the MMI Screen (Figure 1)

Customer Statement: -Various rotating display/screen noises during operation

Customer statement / workshop findings: The Touch Screen Remote (TSR) has no visible display or does not function, see the example shown in Figure 1. Technical background In the event that one or a combination of the described symptoms is evident, please follow the instructions within the Measure section depending on the symptom.

Update (OTA) could be required for both of the Bring Your Own Content (BYOC) screens

Statement: -Bentley rotational display (BRD) operational issues -Mechanical malfunction DTC B140107 evident within 005F

services personalisation feature does no longer function. The in car services personalisation function can be found by navigating through the screen menu.

The Touch Screen Remote (TSR) is not operating (No Display or Functionality)

the Rear Seat Entertainment screens (RSE) is no longer available.

changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit.

the Rear Seat Entertainment screens are not working to specification (icons greyed out) a message is also displayed advising the feature(s) are not available when the icons are pressed.

may cause rattle/buzzing noise from dashboard upper trim panels -Relative movement between control unit for Head-Up Display and associated trimring -Contact between the dashboard and the dashboard upper trim panel -Head-up display internal fault

screen appears to be stuck in the (initializing) stage, when this scenario is evident a spinning wheel is visible

within the MMI screen

the (home) screen, loading messages can be seen in some or all of the titles

Dynamic Ride system fault warning displayed within the DIP

Infotainment Main unit (5F/J794) -MMI screen image flickers or goes blank -No Response to selection -Audio cuts-out

-Bentley rotational display (BRD) operational issues -Mechanical malfunction DTC B140107 evident within 005F

Customer Statement: -The chrome brightware strip on the (veneer face) fascia panel of the Bentley Rotating Display (BRD) may appear to be misaligned with the passenger and/or drivers side fascia panel chrome strips

Customer Statement: -Various rotating display/screen noises during operation. Grinding, rattling, squeaking, creaking, and rattling.

screen appears to be stuck on the "Initialising" stage, when this scenario is evident a spinning wheel is visible Technical Background: -The issue occurs when the Infotainment system is shut down with the "Home" menu screen displayed. The Infotainment will start up on this screen the next time the vehicle is started.

Customer statement / workshop findings: The gap and fit between the veneer face facia panel of the Bentley rotating display (BRD) and the passenger and drivers side fascia panels may differ from one side to the other Depending on vehicle specification, the chrome brightware strip on the veneer face facia panel of the Bentley Rotating Display (BRD) may appear to be misaligned with the chrome strips on the passenger and/or drivers side fascia panels If the minimum functional gap is not maintained, the operation of the (BRD) unit can be compromised Technical background: The chrome brightware strip is fixed to the veneer face fascia panel (with no separate adjustment) and as such can appear to be misaligned. The veneer face fascia panel relies on fixed location pins that may be out of tolerance Referring to the Measure section, rework the veneer face fascia panel to align the chrome brightware strip and/or the gapping between the BRD and the passenger and drivers side fascia panels If the BRD is partially rotated and unresponsive (e.g not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled

Customer statement / workshop findings: Various rotating display operational complaints. The operative should ensure the correct TPI is followed depending on the actual issue(s) as follows: - TPI 2065895/- Rotating display/screen noise - Diagnosis for complaints relating to noise during operation/during a drive cycle, should be considered for any issues which relate to noise issues - TPI 2065896/- Rotating screen alignment IMPORTANT: The Rotating screen alignment TPI should be considered for any issues which relate to noise and overall functionality. HINT: Alignment abnormalities may cause functionality/noise issues - TPI 2065897/- Rotating display inoperative (Rotating display may fail to function or get stuck in one position) should be considered for vehicles up to and including VIN SCBCA13S3KC073865 If the Bentley rotating Display (BRD) is partially rotated and unresponsive (e.g. not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen - However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled NOTE: For all other Bentley rotating display (BRD) operational issues, the operative should follow the remaining instructions within the Measure section of this TPI

Condition: Various rotating display/screen noises during operation Technical Background: If the Bentley Rotating display (BRD) is partially rotated and unresponsive (e.g. not presenting one of the facias) the display must be rotated in order to remove the veneer facia, dials or MMI screen However Manual rotation of the BRD will damage the drive belt and link arm, please raise a DISS query stating the BRD is unresponsive, the DISS query will be evaluated and the BRD unlock procedure will be supplied (If required) Do Not conduct any further work until advised CAUTION: In the event that damage was caused by attempting to rotate the BRD manually without following the BRD unlock procedure the applicable warranty claim may be cancelled The symptoms listed below are listed as a guideline to enable the applicable noise issue to be diagnosed and repaired, in the event the noise and/or symptom does not match any of the Scenarios listed below, the operative should raise a DISS query and await feedback before conducting any further work

Customer statement / workshop findings: Upon start-up of the Infotainment system, the home screen appears to be stuck in the 'Initialising' stage, when this scenario is evident a spinning wheel is visible (Figure 1) Technical background: The issue occurs when the Infotainment system is shut down with the Home menu screen displayed. The Infotainment will start up on this screen the next time the vehicle is started Should the symptoms be the same as the description within the Customer statement/workshop findings section the operative should complete the questionnaire and carry out the instructions within the Measure section of this TPI Once completed the questionnaire should be attached to an existing or already open DISS query

Customer statement / workshop findings Issue suspected with the Infotainment Main unit (5F / J794) - For example: - MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background The operative should continue as follows: - Complete the questionnaire within the Measure section of this TPI (Part 1) once completed the questionnaire should be attached to an existing or already open DISS query - Once the questionnaire is complete, the operative should refer to (Part 2) within the Measure section regarding fault finding/diagnosis of the Infotainment Main unit (5F / J794)

Customer statement / workshop findings: Various rotating display operational complaints or noises. Technical background: Follow the Measure section of this TPI that relates to your customer complaint.

Customer statement / workshop findings: Various rotating display operational complaints or noises. Technical background: Follow the Measure section of this TPI that relates to your customer complaint.

Rotating Display (BRD) may appear to be misaligned with the chrome strips on the passenger and drivers side fascia panels. In addition, the gapping and fit between the veneer face fascia panel of the BRD and the passenger and drivers side fascia panels may differ from one side to the other. The minimum functional gaps between the BRD and the passenger/driver fascia and the switch pack if not maintained can impact on the rotational operation of the BRD unit Technical background: The chrome brightware strip is fixed to the veneer face fascia panel with no separate adjustment and as such can appear to be misaligned. The veneer face fascia panel relies on fixed location pins that may be out of tolerance. Rework the veneer face fascia panel to align the chrome brightware strip and/or the gapping between the BRD and the passenger and drivers side fascia panels.

Technical background: Follow the Measure section of this TPI that relates to your customer complaint. Possible customer complaint. 1. Operational issues 2. Rotating display alignment 3. Grinding noise on operation 4. Rattling noise on operation 5. Squeak/creak on operation 6. Creak/rattle from rotating display whilst driving/uneven operation during rotation

suspected with the Infotainment Main unit (5F / J794) - For example: -MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background: Refer to the Measure section regarding any Infotainment Main unit (5F / J794) fault finding/diagnosis

cracked/damaged Technical background: Please refer to the instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged NOTE: The instructions MUST be followed to help the retailer clarify if the windscreen should be replaced under manufacturers warranty (Stress crack) or Customer pay/insurance (external influence damage)

issue described is evident

Follow the measure section of this TPI that relates to your customer complaint.

Customer statement / workshop findings: The chrome brightware strip on the veneer face fascia panel of the Bentley Rotating Display (BRD) may appear to be misaligned with the chrome strips on the passenger and drivers side fascia panels. In addition, the gapping and fit between the veneer face fascia panel of the BRD and the passenger and drivers side fascia panels may differ from one side to the other. Technical background: The chrome brightware strip is fixed to the veneer face fascia panel with no separate adjustment and as such can appear to be misaligned. The veneer face fascia panel relies on fixed location pins that may be out of tolerance. Rework the veneer face fascia panel to align the chrome brightware strip and/or the gapping between the BRD and the passenger and drivers side fascia panels.

display screen shows Component Protection Active. Diagnostic Trouble Code (DTC) U110100 Component Protection Active stored within 004E (Display/Control head HR) and/or 005E (Display/Control Head LH).

Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference

Customer statement / workshop findings: Yellow Tyre Pressure Monitoring System (TPMS) warning light is evident with the Drivers Information Panel (DIP) The warning is evident when the tyre size has been changed within the MMI For example: After changing the tyres from winter to summer variants or vice versa

Customer statement: One or numerous of the following issues are evident: ACC Failure Traffic Assist Failure Safeguard Failure Radar Malfunction

format for analysis by Product Support Technical Background: The instructions within the Measure section of this TPI have been generated to guide operatives through the process for recording Measured values in cycles by using self diagnosis, the Instructions also detail how to locate corresponding files which are required for analysis

Customer statement / workshop findings: During fault finding, the following may be observed: DTC B200FFE (Internal Malfunction) stored in the following diagnostic address: Front Sway Stablization Control Unit (00D4)Or Rear Sway Stablization Control Unit (00D5)

Customer statement / workshop findings: One or both of the Flying B mascot clear wings are missing

Customer statement / workshop findings: The user list is not populated when selected on the MMI, the following message is evident: Connected Car User List Could Not Be Obtained Due to Communication Problem error message shown within the MMI

Condition: This Technical Product Information (TPI) Document is designed to give repair guidance and standardised fault reporting for Flying B functionality, poor finish and damage concerns.

Condition: This questionnaire is designed to gather all necessary information from retailers before escalating a technical request through DISS for connected car related issues.

Condition: Customer may report that the seat ventilation system is not functioning with no airflow from the seat ventilation ducts.

Condition: Calendar feature in the MMI does not work although the tile is visible Calendar feature in the MyBentley App no longer visible

Customer statement: One or numerous of the following issues are evident: ACC Failure Traffic Assist Failure Safeguard Failure Radar Malfunction

Condition: In some cases Measured value traces may be requested in XML format for analysis by Product Support.

Condition: Customer may report that the seat ventilation system is not functioning with no airflow from the seat ventilation ducts.

Condition: In some cases, Measured value traces may be requested in XML format for analysis by Product Support

Customer statement: One or numerous of the following issues are evident: ACC Failure Traffic Assist Failure Safeguard Failure Radar Malfunction

Customer statement / workshop findings: Water ingress into the left and/or right hand foot well Front carpets and/or foot mats are wet Musty smell in the cabin

Technical background The instructions within the Measure section of this TPI have been generated to guide operatives through the process for recording Measured values in cycles by using self diagnosis, the Instructions also detail how to locate corresponding files which are required for analysis.

Customer statement / workshop findings: One or both of the Flying B mascot clear wings are missing.

Customer statement / workshop findings: Rattle from the MMI switchpack at the locations shown in Figure 1. Technical background: The noise may be from the left and / or right hand metallic clip(s) as shown in Figure 2

Customer statement / workshop findings One or both of the Flying B mascot clear wings are missing. In the event that one Flying B wing is missing the operative must replace both wings to eliminate a repeat repair.

Technical background: In the event the issue is as exactly as described, refer to the instructions within the Measure section.

control interventions experienced upon reaching 30km/h (Figure 1) Technical Background: -In the event the issue is as exactly as described, refer to the instructions within the Measure section

Customer Statement: One or numerous of the following issues are evident: ACC Failure Traffic Assist Failure Safeguard Failure Radar Malfunction

Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

>The boot does not open or close as expected

to give repair guidance and standardised fault reporting for Flying (B) functionality, poor finish and damage concerns.

Technical Background: -Deviations in the key blade and key fob assembly could make it difficult to remove the key blade.

Customer statement / workshop findings: One or numerous of the following issues are evident: - ACC Failure - Traffic Assist Failure - Safeguard Failure - Radar Malfunction Workshop findings: One or a combination of the following DTCs and symptom codes are evident within address 0013 - B200FF0 with Symptom code(s) 1367 and/or 1313 and/or 1334 - Internal Malfunction.

Customer statement / workshop findings: In some cases Measured value traces may be requested in XML format for analysis by Product Support Technical background: The instructions within the Measure section of this TPI have been generated to guide operatives through the process for recording Measured values in cycles by using self diagnosis, the Instructions also detail how to locate corresponding files which are required for analysis Product Support will advise regarding the Measured values and cycle time required.

are missing

are missing

pawl is required

Assist and/or Traffic Assist Are Not Functional

-Vehicle sitting low on one or more corners when static -No relevant DTCs are evident

Assist and/or Traffic Assist are not functional.

Assist and/or Traffic Assist are not functional

about an unexpected safeguard or driver assistance intervention.

to give repair guidance and standardized fault reporting for Flying (B) functionality, poor finish and damage concerns.

symptom present is evident during vehicle start up or similar conditions please refer to TPI 2061171.

is as exactly as described refer to the instructions within the measure section

selected on the MMI, the following message is evident: (Connected Car User List Could Not Be Obtained Due to Communication Problem)

feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported.

-Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle.

camera washer jet

blade and key fob assembly could make it difficult to remove the key blade.

Customer Statement: -ACC failure -Traffic Assist Failure -Safeguard Failure -Radar Malfunction

Condition: Repeated traction control interventions experienced upon reaching 30km/h. Technical Background: In the event the issue is as exactly as described, refer to the instructions within the Measure section

selected on the MMI, the following message is evident: Connected Car User List Could Not Be Obtained Due to Communication Problem error message shown within the MMI Technical Background: -In the event the issue is as described please refer to the Measure section of this TPI

Customer statement / workshop findings: - Vehicle sitting low on one or more corners when static - No relevant DTCs are evident Technical background: Refer to the Measure section of this TPI

Technical background: The white FPIN tag not attached to the vehicle keys. Remedy: Refer to the instructions within the Work section to completion

Technical background: The white FPIN tag not attached to the vehicle keys. Remedy: Refer to the instructions within the Work section to completion

Customer statement: One or numerous of the following issues are evident: - ACC Failure - Traffic Assist Failure - Safeguard Failure - Radar Malfunction Workshop findings One or a combination of the following DTCs and symptom codes are evident within address 0013 -B200FF0 with Symptom code 1367 or 1313 - Internal Malfunction

Customer statement / workshop findings: Rear center armrest lid has poor magnetic retention to the main armrest, this can lead to a crease in the leather. Technical background: Rear center armrest lid has poor magnetic retention to the main armrest.

Document is designed to give repair guidance and standardised fault reporting for Flying B functionality, poor finish and damage concerns.

and/or retailer may identify visual damage/anomalies in the paint finish during or post pre-delivery inspection. These may include: Uneven sheen or texture Patchy or blotchy appearance Inconsistent under lighting Staining, discolouration, or surface blemishes

Customer statement / workshop findings: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness.

Customer Statement: The customer reports that the vehicle door locking and/or unlocking does not function correctly. This may include intermittent operation, non-response to remote or interior commands, or inconsistent locking behaviour.

and/or retailer may identify visual damage/anomalies in the paint finish during or post pre-delivery inspection. These may include: Uneven sheen or texture Patchy or blotchy appearance Inconsistent under lighting Staining, discolouration, or surface blemishes

vehicle door locking and/or unlocking does not function correctly. This may include intermittent operation, non-response to remote or interior commands, or inconsistent locking behaviour.

Customer statement / workshop findings: Driver and / or Passenger door creak during the Power close function - Front and / or rear (Depending on vehicle type)

Evidence of water ingress into the cabin, typically visible on or around the lower door trim area. Damp carpet or moisture traces following rainfall or vehicle washing

Condition: Customers and retailers may raise enquiries regarding the cleaning and appearance of Dinamica interior trim materials. Workshop inspection confirms no material defects, with concerns related solely to approved cleaning and maintenance guidance

Customer Statement: Customers may report a loud or abnormal noise from one side mirror during the automatic folding or unfolding operation.

Condition: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness.

Condition: In rare instances the customer and/or retailer may identify the presence of damage or visual anomalies on leather trimmed surfaces within the vehicle cabin during or post pre-delivery inspection.

Condition: Failure of the door subframe mounting housing

Customer may report one or more of the following issues with the rear door blind: Blind does not retract or extend properly Blind fabric appears damaged or distorted Letterbox-style flap is loose or detached Audible rattling or clicking noise from door panel Blind assembly partially or fully inoperative.

Condition: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness.

Condition: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness

Condition: In the event a complaint is received regarding road wheel/s condition for example: Scratches Corrosion Damage Blemishes Chipping

Customer statement / workshop findings: Front and/or rear internal door trim panel - Poor retention between the door trim panel trim clips and door panel tucker studs.

Technical background: If the complaint is confirmed please refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: Boot release switch (Door) is loose or the switch has dropped into the front door aperture

Customer statement / workshop findings Rattle / Creaking noise from the dashboard demister panel.

Customer statement / workshop findings: Driver and / or Passenger door creak during the Power close function - Front and / or rear (Depending on vehicle type) Technical background: Ensure the fault is as described within the Customer statement Workshop findings section before continuing.

condition for example: - Scratches - Corrosion - Damage - Blemishes - Chipping Please refer to the onward instructions

Technical Background: -In the event there is a customer complaint regarding the opening of the door from the outside of the vehicle when using the door handle (Keyless entry) please refer to the Measure section of this TPI

The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips.

Customer statement: - Water ingress into the left and/or right hand foot well - Front carpets and/or foot mats are wet - The windows are misty due to water ingress Workshop findings - After conducting TPI 2062622/- water ingress was found at the location shown in Figure1 (Left hand A - Pillar seam). The cause of the ingress can be caused by missing sealant on the A - post pillar seam.

Statement: -Window lift switch is loose within the door aperture -Or The window lift switch rattles when the door is closed

should be followed to assist in the diagnosis of water leaks or wind noise.

during the (Power Close) function

Technical Background: -In the event there is a customer complaint regarding the opening of the door from the outside of the vehicle when using the door handle (keyless entry) please refer to the measure section of this TPI

condition for example: -scratches -corrosion -damage -blemishes -chipping

lamps are steamed up/damp from the inside with minor drips

Connected Services at PDI and/or The SOS LED in roof console is either lit red or flashing red and/or the test call is unable to complete.

during the (power close) function

Customer Statement: -Blind spot monitors (Wing mirror illuminations) are not functional in conjunction with sporadic Bentley assist warnings present in the DIP Technical Background: -As per the Workshop findings section the operative should review the Theory of operation chapter for the Rear radar

- Standard (STD) not Privacy (PRV) or visa versa and/or Defects are evident within the glass Technical Background: -The instructions within the Measure section MUST only be followed if the glass is to be replaced

Customer statement / workshop findings: In the event that a trim mismatch is detected for example: - Piano black veneer is supplied although the customer ordered walnut veneer Or - The interior trim colour is incorrect for example: Cricket ball interior trim is supplied although the customer ordered Hotspur The operative should refer to the Technical background section

Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera washer jet Technical background: Please note: The photographs shown within this TPI are based on a New Continental GT/C vehicle however the process is similar regardless of vehicle type Referring to Figure 1 - In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the night vision washer jet (short link hose -Circled) which connects the night vision camera washer jet (A) to the washer jet supply hose connector (B) Measure: 1) Referring to Rep.Gr 63 Remove the front bumper lower inner grilles 2) Disconnect the hose from the night vision camera as shown in Figures 2 and 3 Please note: Washer fluid may leak once the hose is disconnected - Ensure a suitable container is used to collect the fluid, all fluid MUST be discarded as per all local environmental guidelines

the instructions within the owner handbook). Production change: Owner handbooks for later vehicles/models will be revised. Amended owner handbooks or addendums will not be available for this particular issue.

Condition: Driver or Passenger door creak during the Close function Technical Background: Refer to the vehicle repair history to check and confirm any previous work done regarding door latch replacement noting the following: - Only replace the door latch which is exhibiting the symptom

following issues found during the Pre Delivery Inspection (PDI). Unable to complete set-up of Connected Services at PDI and/or the SOS LED in roof console is either lit red or flashing red and/or the test call is unable to complete.

Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

Customer statement / workshop findings Customer statement: 1. The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. or 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips. Technical background 1. Damp air settles on the inner lens of the headlights/fog lamps, with recognisable misting in certain weather conditions (comparable with the steaming up of spectacle lenses when entering a warm room in winter or of the bathroom mirror after a shower). 2. Leak on the headlights/front fog lamps. For example through open covers, a damaged seal of the cap or similar.

post trim panel when the rear seats are occupied and when the vehicle is static. Workshop findings: Creaking noise from the left or right upper C post trim panel can be identified when pressing the panel by hand. The instructions MUST only be conducted on receipt of an official customer complaint. Technical background: IMPORTANT: Ensure all trim panels are suitably protected when carrying out the onward instructions Warranty payment will not be considered for any trim damage. IMPORTANT: The operative should perform the onward instructions within the Measure section on the affected side only. The instructions MUST only be followed on the right and left hand side in the event that the issue is clearly evident on both sides.

Scratches - Corrosion - Damage - Blemishes - Chipping Please refer to the onward instructions. Technical background: Do not consider submitting a warranty claim for a road wheel manufacturing defect without first referencing and understanding the contents of this document. Any defect or concern found either outside the guidelines stated in this document or not clearly stated as acceptable to support a warranty claim, will be the responsibility of the retailer regarding component replacement. Any road wheels deemed as having no issues found relating to a manufacturing defect (including curbing) will have the applicable claim rejected

Customer statement / workshop findings: During diagnosis using ODIS, Measured Value Blocks (MVBs) for: Visible satellites, tracked satellites (within J949 Emergency Call Control Module Conbox) may display blank or no value. This condition may be interpreted as a GPS reception fault, antenna issue or connectivity malfunction. Diagnostic logs may also show absence of satellite values.

The following issues could be evident during PDI or found whilst in service: Electronic Parking Brake (EPB) found not operating to specification EPB may not hold the car effectively Parking brake components showing signs of wear Parking brake warning light may also be evident within the DIP, stating Parking brake fault detected. Stop the vehicle in a safe place and refer to the owners manual.

Condition: Groaning/creaking noise heard from the brake pedal during light application, in particular when the vehicle is at operating temperature.

Technical Background: Brake noises can be attributed to many causes, the most common causes are as follows: Brake discs or pads are close to their wear limit New brake pads and/or discs have not been properly bedded in after installation Aftermarket pads or discs are installed There is debris such as small stones, grit, road salt or sand between the brake disc and pad Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time

Customer statement / workshop findings: The following issues could be evident during PDI or found whilst in service: - EPB may not hold the car effectively - Parking brake components showing signs of wear - Parking brake warning light may also be evident within the DIP.

-The noise/squeal can be reproduced and clearly assigned to the braking system

warning within the DIP with one or both DTCs as listed below: C100C01: Electro-mechanical parking brake button electrical error And/or C1246F9: Electromechanical parking brake Button interruption.

The following issues could be evident during PDI or found whilst in service - Electronic Parking Brake (EPB) found not operating to specification - EPB may not hold the car effectively - Parking brake components showing signs of wear - Parking brake warning light may also be evident within the DIP (See example shown in Figure 1)

Customer statement / workshop findings: Parking brake warning light evident within the DIP (See example shown in Figure 1). Measure: Raise a technical DISS query ensuring a current ODIS log is attached

Statement: -The rear brake callipers do not have the brand name lettering (Bentley) applied to the rear brake callipers however -The front brake callipers do have the brand name lettering (Bentley) applied to the front brake callipers

PDI or found whilst in service -Electronic Parking Brake (EPB) found not operating to specification -EPB may not hold the car effectively -Parking brake components showing signs of wear -Parking brake warning light may also be evident within the DIP

-Electro-mechanical parking brake button electrical error and/or -Electro-mechanical parking brake button interruption

PDI or found whilst in service -Electronic Parking Brake (EPB) found not operating to specification -EPB may not hold the car effectively -Parking brake components showing signs of wear -Parking brake warning light may also be evident within the DIP Technical Background: -The issues described can be evident due to the car being driven in Transport mode with the EPB applied during the Transit process or in some cases similar symptoms may be seen whilst in service

brake warning light evident within the DIP

Customer statement / workshop findings: The rear brake calipers do not have the brand name lettering Bentley applied to the rear brake calipers However The front brake calipers do have the brand name lettering Bentley applied to the front brake calipers Technical background: Refer to the production change section Production change: All vehicles which have been produced post 31.05.2022 onwards do not have the brand name lettering Bentley lettering applied to the rear brake calipers as shown in Figure 1

Customer statement / workshop findings: The following issues could be evident during PDI or found whilst in service - Electronic Parking Brake (EPB) found not operating to specification - EPB may not hold the car effectively - Parking brake components showing signs of wear - Parking brake warning light may also be evident within the DIP (See example shown in Figure 1. Technical background: The issues described can be evident due to the car being driven in Transport mode with the EPB applied during the Transit process Or In some cases similar symptoms may be seen whilst in service.

Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Service: Note: For correct diagnosis and repair the attached Flowchart must be followed. 1. Check the overall condition of the brakes to determine if the brake noise can be attributed to one of the causes listed in the Technical Background section of this TPI. If the noise is not a result of one these causes, proceed with point 2. 2. Record the noise and frequency For the frequency analysis and the noise recording we recommend using the Chassis Ear Tool WT 10437. To record the noise and measure the frequency using WT 10437 Chassis Ear Tool follow these instructions; Refer to File recording in the WT 10437 user instructions.

Customer statement / workshop findings: - Undesirable odour emanating from the front wheel arches, the issue occurs after the vehicle has reached normal operating temperature - The odour can also be evident within the cabin Technical background: HINT: The issue described is mainly evident on low mileage/low use vehicles with iron brakes In the event the symptoms are as described, please conduct the instructions within the Measure section of this TPI

Customer statement / workshop findings: The following issues could be evident during PDI or found whilst in service - Electronic Parking Brake (EPB) found not operating to specification - EPB may not hold the car effectively - Parking brake components showing signs of wear - Parking brake warning light may also be evident within the DIP (See example shown in Figure 1) Measure: 1) Carry out a full inspection of the (Electronic Parking Brake EPB) system including the following components: - Right and left hand (EPB) Actuators - Right and left hand rear brake shoes (EPB) See example shown in Figure 2

Customer statement / workshop findings: EPB fault warning within the DIP with one or both DTCs as listed below: C100C01: Electro-mechanical parking brake button electrical error And/or C1246F9: Electromechanical parking brake Button interruption.

Warning within the DIP Workshop findings: One or a combination of the following DTCs and symptom codes are evident within address 003 - P191F00 4538626 - Pressure sensor for brake booster Electrical malfunction (Front Right Corner Pressure Sensor Fault) - C054100 4538624 - Brake Pressure Sensor "B" Range/Performance (Rear left Pressure Sensor Fault) - C054200 4538880 - Brake Pressure Sensor "B" Circuit Low (Rear left Pressure Sensor Fault)

Condition: The right and/or left hand front rearmost lower suspension lever inner hydraulic mounts are leaking oil or showing signs of dry oil stains

Customer statement: Air suspension warning light within the DIP.

Customer statement: Unusual air suspension behaviour when the vehicle is static for example: Air suspension raising and lowering without request NOTE: Customer complaints regarding hard suspension when driving the vehicle may also be received

Customer statement: Unusual air suspension behaviour when the vehicle is static for example: Air suspension raising and lowering without request NOTE: Customer complaints regarding hard suspension when driving the vehicle may also be received

Customer statement / workshop findings: Customers will not be aware of any DTCs, workshop operatives may discover spurious DTCs whilst running Guided Fault Finding (GFF) when using ODIS Technical background: To determine the course of action which should be taken the operative should refer to the Bentley Hub referencing the following: Spurious DTC list for TPI 2072055 The document contains all known spurious DTCs for all applicable vehicle variants.

Statement: -Air suspension warning light within the DIP

Customer statement / workshop findings: Customers will not be aware of any fault codes Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).

Customer statement / workshop findings: Grease evident on or around the front axle lower ball joint bellows In the event the symptom is as described, the operative should carry out the instructions within the Measure section Technical background: During service work and/or other repairs, a loss of grease can be detected from the front axle lower ball joint on one or both lower ball joint bellows. Measure: Findings performed on supposedly damaged components have shown that they were of good quality, no damage was found to the ball joint bellows which could of resulted in the leak Grease may leak during the initial assembly of the front lower levers. This due to a maximum deflection of the conical spigot before the lower lever is assembled into the wheel carrier. Over the service life, additional foreign bodies can collect in the corresponding area and stick to the excess grease, which can then be distributed over a larger area If there is no customer complaint about noises (rattling, pinching, creaking) from the area of the front axle and the lower levers have clearance, the operative must remove any excess grease and check the ball joint and bellows for damage If the ball joint/bellows is not damaged, the lower lever does not need to be replaced The level of grease on or around the lower ball joint boot/wheel bearing housing (Figures 1,2 and 3) is deemed as a normal characteristic.

a loss of grease can be detected from the front axle lower ball joint on one or both lower ball join bellows

Technical background: -Additional steps added within the Measure section relating to air spring damper checks

Technical Background: -The fluid shown in figures 1 and 2 is assembly fluid residue. The fluid is applied to various internal components of the air spring during manufacture.

Customer statement / workshop findings: -Customers will not be aware of any fault codes -Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: -The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants -Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).

list can be found within the Bentley Hub The white FPIN tag is not attached to the vehicle keys to the vehicle keys (SC22/13) In the event the white FPIN tag is evident as shown in 2 and 3, the 10 digit FPIN vehicle code can be entered into MMI, in this scenario there is no need to raise a DISS query for a new FPIN, the operative should refer to the Identification section of this TPI to ensure the specific VIN is removed from the applicability list.

Technical background: Please Note: This is an ongoing exercise and therefore the latest VIN list can be found within the Bentley Hub. The white FPIN tag not attached to the vehicle keys. Remedy: Refer to the instructions within the Work section to completion.

Customer statement / workshop findings: - Vehicle sitting low on one or more corners when static - No relevant DTCs are evident Technical background Refer to the Measure section of this TPI Measure: 1) Confirm there are no DTCs indicating a fault with the air suspension system or associated systems 2) Refer to the instructions within TPI 2053492/- to confirm that no air leaks or issues relating to the air springs are evident

Customer statement / workshop findings Unusual air suspension behaviour when the vehicle is static for example: - Air suspension raising and lowering without request NOTE: Customer complaints regarding hard suspension when driving the vehicle may also be received Technical background. To confirm the issue is as described within the Customer statement refer to the video on the Bentley Hub referencing TPI 2064555/- In the event that the issue is as shown within the video the instructions within the Measure section should be followed

fault is as described within the Customer statement, refer to the video on the Bentley Hub referencing TPI 2061605/- In the event the symptom is as shown the instructions within the Measure section should be followed NOTE: The video shown on the Bentley Hub is for reference purposes only, the symptom is the same regardless of vehicle type shown

Customer statement / workshop findings - Vehicle sitting low on one or more corners when static - No relevant DTCs are evident Technical background: Refer to the Measure section of this TPI. Measure: 1) Confirm there are no DTCs indicating a fault with the air suspension system or associated systems 2) Refer to the instructions within TPI 2053492/- to confirm that no air leaks or issues relating to the air springs are evident.

Customer statement / workshop findings: Driver or Passenger door creak during close Technical background: Ensure the fault is as described within the Customer statement, refer to the video on the Bentley Hub referencing TPI 2061605/- In the event the symptom is as shown the instructions within the Measure section should be followed.

Customer statement / workshop findings Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the document (loaded onto the Hub) regarding the DTC description and actions (if any) which should be conducted

Customer statement / workshop findings: Headlamp low beam / high beam malfunction / operational issues (Inner lamp) Or Daytime running light malfunction / operational issues (Inner lamp) Or Turn signal malfunction / operational issues (Outer lamp)

Customer statement / workshop findings: Headlamp low beam / high beam malfunction / operational issues (Inner lamp) Or Daytime running light malfunction / operational issues (Inner lamp) Or Turn signal malfunction / operational issues (Outer lamp)

Condition: Headlamp low beam / high beam malfunction / operational issues (Inner lamp) Or Daytime running light malfunction / operational issues (Inner lamp) Or Turn signal malfunction / operational issues (Outer lamp).

Condition Headlamp low beam / high beam malfunction / operational issues (Inner lamp) Or Daytime running light malfunction / operational issues (Inner lamp) Or Turn signal malfunction / operational issues (Outer lamp).

Customer statement / workshop findings: The customer complains that the mobile device sometimes cannot be charged wirelessly. One of the following three situations is described: The phone gets very hot while charging and charging is cancelled. The phone is not charged and the following message is shown on the MMI: The device cannot be charged as there is another object in the charging cradle. The phone does not start charging after it has been placed in the charging cradle. The phone or individual processes are switched off to protect the phone as a result of heat generation. The mobile device supports wireless charging or the customer uses a charging cover that enables wireless charging

Customer statement / workshop findings: Headlamp low beam / high beam malfunction / operational issues (Inner lamp) Or Daytime running light malfunction / operational issues (Inner lamp) Or Turn signal malfunction / operational issues (Outer lamp).

Customer statement / workshop findings: Operational issues are evident with one or a combination of the following: - Headlamp low beam / high beam malfunction / operational issues (Inner lamp) Or - Daytime running light malfunction / operational issues (Inner lamp) Or - Turn signal malfunction / operational issues (Outer lamp) Or Numerous static and/or intermittent DTCs are evident within the left light control unit (Diagnostic address D6) and/or the right light control unit (Diagnostic address D7)

headlamp is flickering

Customer statement / workshop findings: Headlamp is not working or the headlamp is flickering Workshop findings Headlamp assembly diagnosed as faulty. Technical background: It is not possible to determine between internal lamp defects and control unit failures therefore this TPI is to advise the replacement of the control unit in the first instance The complete headlamp assembly should only be replaced if control unit replacement was not successful.

Customer statement: Headlamp is not working or the headlamp is flickering Workshop findings Headlamp assembly diagnosed as faulty. Technical background: It is not possible to determine between internal lamp defects and control unit failures therefore this TPI is to advise the replacement of the control unit in the first instance The complete headlamp assembly should only be replaced if control unit replacement was not successful.

Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera washer jet Technical background: Please note: The photographs shown within this TPI are based on a New Continental GT/C vehicle however the process is similar regardless of vehicle type Referring to Figure 1 - In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the night vision washer jet (short link hose -Circled) which connects the night vision camera washer jet (A) to the washer jet supply hose connector (B) Figure 1

lighting strip is faulty/incorrect illumination due to the strip being cracked and/or irregularities in the strip -Mood lighting strip has incorrect color synchronization and/or sticks to one color -Mood lighting strip has partial illumination and does not light at all

-Raise a technical DISS query

Technical Background: -Due to the design and fitment of the rear lights in relation to the surrounding components the operative must refer to the applicable Rep. Gr to confirm if the gap/profile of the rear lamps is to specification before conducting any adjustments or before raising a technical DISS query.

selected or not illuminated at all.

Customer statement / workshop findings: Washer fluid dripping/leaking from the night vision camera washer jet. Technical background: Please note: The photographs shown within this TPI are based on a New Continental GT/C vehicle however the process is similar regardless of vehicle type Referring to Figure 1 - In the event the afore mentioned symptom is evident the operative should refer to the Measure section of this TPI to replace the night vision washer jet (short link hose -Circled) which connects the night vision camera washer jet (A) to the washer jet supply hose connector (B)

Technical Background: DTCs evident within the left light control unit (Diagnostic address D6) and/or the right light control unit (Diagnostic address D7) There are numerous static and intermittent DTCs which may be evident within the previously mentioned control units, ensure all steps within the Measure section are strictly adhered to.

colour scheme is selected or not illuminated at all Technical background: Refer to the Measure section of this TPI.

Customer statement / workshop findings: Complaints relating to My Bentley connected services.

Customer statement / workshop findings: For any interior veneer replacement: raise and obtain approval of a Technical DISS query before ordering. This ensures VIN correct specification and prevents visual mismatch.

Technical background: Conversion of a vehicle for use in a market other than the one for which it was originally designed or intended is not supported. Enquiries related to conversions or retrofits of vehicles from (or to) other markets (e.g. reimport from USA or UK) are not supported by Technical Support. Vehicles are developed and constructed according to specific market requirements of the respective destination country. As the compatibility of different components (e.g. control units) cannot be defined comprehensively regarding their mutual dependence and interaction in the case of modifications, and in order to prevent danger or risks due to constructional changes, support or advice regarding these modifications cannot be provided.

Customer statement / workshop findings: Complaints relating to My Bentley connected services

services.

Condition: For any interior veneer replacement: raise and obtain approval of a Technical DISS query before ordering. This ensures VIN correct specification and prevents visual mismatch.

Customer statement / workshop findings: Front seat adjustment switch is broken / damaged.

Customer statement / workshop findings: Front seat adjustment switch is broken / damaged

Customer statement / workshop findings Workshop findings: Front anti roll bar link lower bushes have small cracks on the surface. Technical background Front anti roll bar links have been incorrectly diagnosed and unnecessarily replaced Front anti roll bar links were replaced due to minor splits being identified during a routine service inspection or noise complaints. Do Not replace the front anti roll bar links when small splits are identified on the lower bushes as shown in Figure 1.

both of the centre console storage box frame ribs as described within the Measure section is required.

both of the centre console storage box frame ribs (Figure 1) as described within the Measure section is required

services can be resolved by contacting My Bentley Support rather than raising a DISS technical query. My Bentley support have access to additional admin tools and systems to help resolve any queries; and also have ability to raise DISS technical queries if required.

Customer statement / workshop findings: Front and/or rear towing eye cover missing at PDI Technical background: Towing eye cover/s found to be missing whilst carrying out the Pre Delivery Inspection

Customer statement / workshop findings: Complaints relating to My Bentley connected services. Technical background: Most queries and complaints regarding My Bentley connected services can be resolved by contacting My Bentley Support rather than raising a DISS technical query. My Bentley support have access to additional admin tools and systems to help resolve any queries; and also have the ability to raise DISS technical queries if required.

Customer statement / workshop findings: In the event a customer complaint is received relating to a suspicion that control units or services have been influenced by third parties the instructions within this TPI should be followed. Technical background: A suspicion that control units or services have been influenced by third parties means that unauthorised people or groups may have gained access to a vehicle's control unit(s) or online services and may have manipulated them in such a way that may compromise customer data confidentiality or the operation of the vehicle and/or online services. When investigating potential third party influences of control units or online services, it is important to take all normal diagnostic measures to rule out a normal functional error or misuse of the system by the user

Customer statement / workshop findings: Complaints relating to My Bentley connected services. Technical background: Most queries and complaints regarding My Bentley connected services can be resolved by contacting My Bentley Support rather than raising a DISS technical query.

and / or Cooling performance has declined over time.

Customer Statement: The customer may find that the A/C system not blowing cold air and / or Cooling performance has declined over time.

Customer Statement: The customer may find that the A/C system not blowing cold air and / or Cooling performance has declined over time.

Customer Statement: The customer may find that the A/C system not blowing cold air and / or Cooling performance has declined over time.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.

expected

Customer statement / workshop findings: Upon start-up of the Home screen, loading messages can be seen in some or all of the tiles (Figure 1) Technical background: A delay when loading tiles is normal, this is due to the amount of external data that is required to load each individual tile, including multiple pages of external data that can be associated with each individual tile. Some tiles will naturally take longer to load than others. For example, APPS, NAVIGATION and MEDIA are likely to have a greater delay in loading than other tiles this is due to the amount of external data required to display the relevant information. TIP: If required, the delay can be reduced by only selecting tiles that do not communicate with external data sources, for example CAR or CLIMATE functions The operative should complete the questionnaire within the Measure section of this TPI, once completed the questionnaire should be attached to an existing or already open DISS query the operative should await feedback before conducting any further work

Customer statement / workshop findings: Upon start-up of the Home screen, loading messages can be seen in some or all of the tiles. Technical background A delay when loading tiles is normal, this is due to the amount of external data that is required to load each individual tile, including multiple pages of external data that can be associated with each individual tile. Some tiles will naturally take longer to load than others. For example, APPS, NAVIGATION and MEDIA are likely to have a greater delay in loading than other tiles this is due to the amount of external data required to display the relevant information. TIP: If required, the delay can be reduced by only selecting tiles that do not communicate with external data sources, for example CAR or CLIMATE functions. A technical DISS query should be raised by the retailer to highlight the issue described is evident.

Condition: Clicking noise from the front wheels whilst performing a static lock to lock steering maneuver.

Customer statement: Rear Steering Fault warning present within the DIP.

-Verify the customer complaint matches the video within the Bentley Hub - Reference TPI Transaction number 2060446/-

Statement: -DTC's C135DF0 and/or C12F000 evident within the Steering rack and power steering control unit (J500) Diagnostic address 44

-Verify the customer complaint matches the video within the Bentley Hub - Reference TPI Transaction number 2060446/-

column will not adjust in any direction

squeaking noise from the bulkhead steering shaft seal is evident

Customer Statement: -Rear steering fault warning present within the DIP

Background: -Refer to the measure section of this TPI

is pulling to the left or right -Steering wheel vibration -General vehicle geometry concerns

workshop findings: Clicking noise from the front wheels whilst performing a static lock to lock steering manoeuvre Technical background: Verify that the customer complaint matches the video within the Bentley Hub Reference TPI Transaction number 2060446/- The operative MUST ensure that all similar symptom TPIs are checked to ensure the fault is exactly as described

/ workshop findings: DTC's C135DF0 and/or C12F000 evident within the Steering rack and power steering control unit (J500) Diagnostic address 44 Referring to Figure 1 Check and confirm the Software version number is 2110 - Should the Software version number be at 2110 the operative should conduct Section 1 of this TPI - Should the Software version number be one of the versions shown below, the operative should conduct Section 2 of this TPI

cases: Airbag/belt released/not released General accident Fire and scorching damage for all Bentley Vehicle models - every model year.

Customer Statement: The customer reports that the airbag warning lamp is illuminated in the instrument cluster and the front passenger airbag indicator lamp within the roof console does not function.

Customer Statement: The customer reports that the airbag warning lamp is illuminated in the instrument cluster and the front passenger airbag indicator lamp within the roof console does not function. Figure

There is a reporting obligation in the following cases: Airbag/belt released/not released General accident Fire and scorching damage for all Bentley Vehicle models - every model year.

There is a reporting obligation in the following cases: Airbag/belt released/not released General accident Fire and scorching damage for all Bentley Vehicle models - every model year.

the drivers seat belt not fastened although the Owners handbook states that the drivers seat belt must be fastened for the Start/Stop system to function

a combination of the following DTCs are evident within the airbag control unit J234

seat belt buckle, the occupant may use the dummy seat belt buckle to prevent a warning light or audible warnings

NOT be used under any circumstances.

seat belt buckle stop button should be evident as shown in Figure 1. Should the seatbelt be as shown in Figure 2 (Buckle stop button missing OR broken/loose) - Refer to the Measure section of this TPI

Measure: Replace the affected seatbelt assembly

Technical background section of this TPI.

Customer Statement: The customer may find that the A/C system not blowing cold air and / or Cooling performance has declined over time.

Customer Statement: The customer may find that the A/C system not blowing cold air and / or Cooling performance has declined over time.

Technical background section of this TPI Technical Background: Details on the introduction of E10 fuel which contains 10% ethanol and its usage on Bentley products All vehicles produced post 1990 Model year can be run using E10 fuel However All vehicles produced before 1990 Model year MUST NOT use E10 fuel

Customer statement: Fuel gauge does not change during a long journey or after refuelling the vehicle and does not show full after filling the fuel tank.

Statement: -Emission control system warning light illuminated within the DIP

illuminated within the Driver Instrument Panel (DIP) -"Drive System Fault. Contact your Bentley Dealer"

will be integrated within the PDI procedure. -All Emergency call function operating instructions can be found within the Owners handbook (Making an emergency call)

illuminated on Driver Instrument Panel (DIP) -(Drive system fault. Contact your Bentley Dealer) displayed on DIP

to the Technical background section of this TPI

within the PDI procedure All Emergency call function operating instructions can be found within the Owners handbook (Making an Emergency call)

Customers may report one or more of the following concerns: Transmission related warning messages displayed in the instrument cluster. Irregular or unexpected gearshift behaviour. Intermittent drivability concerns.

Condition Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system

Customer statement: Noise complaint from the suspension and/or steering.

reverse gear selected.

the transmission link harness to the mechatronic unit for dual clutch gearbox - J743 connections can lead to various and/or numerous transmission control module DTCs being logged

Technical background: Software updates are available and should be applied to the following control unit: Transmission (address 02).

Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system

examples in Figures 1 and 2 showing cracks within the tread pattern)

Workshop Findings: -The following DTC are evident: -P042000: Catalyst System, Bank1 Efficiency Below Threshold -P043000: Catalyst System, Bank2 Efficiency Below Threshold

Background: -The issue is mainly evident on vehicles with very low usage This is a result of the tyre compound hardening due to the following: -Tyre age -Tyre pressure not adjusted to specification -Low mileage/vehicle usage -Vehicle storage conditions

Technical background: Incorrect coding within the Tyre Pressure Monitoring System (TPMS) transmitters The incorrect coding prevents the TPMS control unit from determining the rotational direction of the transmitters Remedy: Replacement of all four TPMS transmitters: - Front left - Front right - Rear left - Rear right

Technical background Incorrect coding within the Tyre Pressure Monitoring System (TPMS) transmitters The incorrect coding prevents the TPMS control unit from determining the rotational direction of the transmitters Remedy Replacement of all four TPMS transmitters - Front left - Front right - Rear left - Rear right

Customer statement / workshop findings: Cracks evident in the sidewall and/or tread pattern (See the examples in Figures 1 and 2 showing cracks within the tread pattern). The issue is mainly evident on vehicles with very low usage This is a result of the tyre compound hardening due to the following: - Tyre age - Tyre pressure not adjusted to specification - Low mileage/vehicle usage - Vehicle storage conditions

The customer complains that the mobile device sometimes cannot be charged wirelessly.

Customer statement / workshop findings: Netflix application update prompt is shown within the (BYOC) rear seat entertainment system. Technical background: In the event the issue described is evident the operative should conduct the instructions within the Measure section.