2017 Bentley Continental TSBs

Customer statement / workshop findings: - HVAC distribution/operational issues - HVAC motor defect (DTCs) evident within address 08 - Climatronic control unit, the DTCs can be static or Intermittent Technical background: Where VIN applicable the operative MUST first conduct Service Campaign EB28 (Bentayga) or EB29 (New Continental GT/GTC).

up or replacing

suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

Customer statement / workshop findings: - Poor engine running - Reduced power - Engine warning lamp illuminated - Symptom related DTCs evident within the applicable engine control unit(s) Technical background: Technical Product Information (TPI) to assist retailers when diagnosing poor engine running or misfires.

engine warning lamp illuminated.

-The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. -The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type -Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering.

engine warning lamp illuminated.

Background: -Bentley vehicles which are applicable to this TPI are fitted with air springs as part of the suspension system. Should air leak from the air spring dampers, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. -The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air supply unit, pipes, valve unit and air reservoirs. This includes potential air leak points on the air spring dampers and also the locations of an air leak that can be repaired without the need to replace an air spring damper.

Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring.

Customer statement / workshop findings Workshop findings: Buzzing noise heard at idle from the sump area when the vehicle is elevated on a workshop ramp. The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances. Technical background: A buzzing noise can be generated by the oil pump when the engine is running at idle. Measure: Test a comparable vehicle with the same Engine derivative. If the same noise is apparent on the comparable vehicle and no oil pressure warnings or relevant DTCs are stored then the noise can be considered a characteristic of the vehicle and no further action should be taken.

Technical background: We have observed instances where the caps have been difficult to remove once fitted, the issue is caused by corrosion. The valve stem itself is made from aluminium and the accessory valve caps are chromium plated brass, it is possible under certain environmental conditions, particularly winter road salt, for corrosion to take place between these dissimilar metals. Measure: The solution is to apply a thin smear of silicon-based grease, such as Dow Corning high vacuum grease, to the external threads of the valve stem prior to fitting the accessory valve cap. Grease should be applied any time the cap is removed and grease is not evident

Customer statement / workshop findings: Engine oil level requires top up between services Technical background: The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.

Customer statement/workshop findings: Check engine warning lamp illuminated on Drivers Instrument Panel. DTCs stored within the Engine Control Module (ECM) Technical background: Internal failure of Inlet or Exhaust Camshaft Adjuster may result in Malfunction Indicator Lamp illumination and DTCs stored within the ECM

Customer statement / workshop findings: Engine oil level requires to:p up between services. Technical background The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Condition: Oil loss/drips on underbody, engine oil loss between engine and gearbox Technical Background: Oil loss via thread of fasteners in crankshaft used to attach torque convertor drive plate/flywheel. New bolt specified with thread sealer pre applied, part number WHT005487A.

Should an issue be diagnosed or reported regarding any part of the vehicles main harness or engine harness resulting in a requirement to raise a DISS ticket, please follow all instructions within this TPI to ensure that your Bentley Motors Technical Service Centre (TSC) receives all required and relevant information. Technical background: In order for the Bentley Motors Technical Service Centre (TSC) to resolve any issues relating to the vehicles main harness or engine harness please follow the instructions within this TPI. Refer to Section 1 for the main vehicle harness identification label location Refer to Section 2 for the engine harness identification label location

be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if any TPIs are applicable to the customers complaint/issue, should an applicable TPI be available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required) For correct diagnosis and repair, the attached Flowchart must be followed in conjunction with the Measure section of this TPI

Technical Background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfires. Service: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.

Technical Background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. Please follow and complete the check list within the Measure section of this TPI to help in diagnosing the issue (the check list does not need to be sent as an attachment should a DISS technical query be raised) . Should a leak be found from an air spring, compressor, valve unit or reservoir, please raise a DISS technical query and include as much information as possible including photograph/s of the leak/s location. Once the DISS ticket has been submitted please await clarification from your TSC before commencing with replacing any of the suspected faulty air springs. Mandatory reporting is applicable for all air spring related issues.

- V8 4.0 TFSI

Customer statement / workshop findings: Driver and / or Passenger door creak during the Power close function - Front and / or rear (Depending on vehicle type).

Customer statement / workshop findings: Driver and / or Passenger door creak during the Power close function - Front and / or rear (Depending on vehicle type) Technical background: Ensure the fault is as described within the Customer statement Workshop findings section before continuing.

condition for example: - Scratches - Corrosion - Damage - Blemishes - Chipping Please refer to the onward instructions

The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips.

should be followed to assist in the diagnosis of water leaks or wind noise.

condition for example: -scratches -corrosion -damage -blemishes -chipping

lamps are steamed up/damp from the inside with minor drips

Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

Customer statement / workshop findings Customer statement: 1. The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. or 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips. Technical background 1. Damp air settles on the inner lens of the headlights/fog lamps, with recognisable misting in certain weather conditions (comparable with the steaming up of spectacle lenses when entering a warm room in winter or of the bathroom mirror after a shower). 2. Leak on the headlights/front fog lamps. For example through open covers, a damaged seal of the cap or similar.

Scratches - Corrosion - Damage - Blemishes - Chipping Please refer to the onward instructions. Technical background: Do not consider submitting a warranty claim for a road wheel manufacturing defect without first referencing and understanding the contents of this document. Any defect or concern found either outside the guidelines stated in this document or not clearly stated as acceptable to support a warranty claim, will be the responsibility of the retailer regarding component replacement. Any road wheels deemed as having no issues found relating to a manufacturing defect (including curbing) will have the applicable claim rejected

Customer statement / workshop findings: Water leak/wind noise evident Technical background: The instructions within the Measure section should be followed to assist in the diagnosis of water leaks or wind noise

Customer statement / workshop findings: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips. Technical Background 1. Damp air settles on the inner lens of the headlights/fog lamps, with recognisable misting in certain weather conditions (comparable with the steaming up of spectacle lenses when entering a warm room in winter or of the bathroom mirror after a shower). 2. Leak on the headlights/front fog lamps. For example through open covers, a damaged seal of the cap or similar.

Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

Technical Background: -Deviations in the key blade and key fob assembly could make it difficult to remove the key blade.

feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported.

Customer statement / workshop findings: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted.

Customer statement / workshop findings: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted

Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

Customer statement / workshop findings Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. All Vehicle Variants - Spurious DTC List Technical background The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted

lid does not attempt to power close when the boot close switch (located on the inside of the boot lid) is pressed. Technical background: In the event the power boot does not attempt to close when the boot close switch is pressed please check the applicability of the model and VIN shown in the Production change section of this TPI before commencing.

clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if there are any TPIs which are applicable to the customers complaint/issue if there is an applicable TPI available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required). For correct diagnosis and repair the attached Flowchart must be followed in conjunction with the Measure section of this TPI

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Measure: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken.

Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section.

Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section

Technical background: If an issue is suspected for one of the control modules listed below: - Onboard supply control unit (J519) - Convenience system central control unit (J393) - Data bus diagnostics interface (J533) - Control unit 1 for Information Electronics (J794) - Control unit in dash panel insert (J285) - Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query. The donor of parts should only be used as a temporary test VERY IMPORTANT: The ODIS replace routine MUST NOT be carried out under any circumstances.

parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the measure of this section of this TPI.

Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.

Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

Customer statement Night vision warning lamp (Figure 1) is evident with the Drivers Information Panel (DIP). Measure 1) Check and Confirm there is no damage to the Night vision camera lens - Check and confirm the camera is secure NOTE: Should no issues be found carry out the remaining onward instructions: - Follow the applicable DTC related test plan within ODIS to completion 2) Proceed with the replacement of the Night vision Control unit if required (as per test plan instruction) - Refer to Rep.Gr 44 - Control unit for night vision (J853) - To remove and fit NOTE: The operative MUST ensure the Night vision camera is calibrated as per Rep.Gr 44

Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.

Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI

defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI

aware of this code / Workshop may discover this code whilst running a Diagnostic Trouble Code log as part of other investigations on the car Technical background: At low ambient temperatures a spurious fault code may be logged by the HVAC control module in reference to the air quality sensor. The code is stored without being accompanied by any functional failure in the system Measure: The following may be seen during routine interrogation of vehicle systems do not take any investigative action in response to the following fault code unless there is an actual fault evident in the system or a fault in the system has been reported by the owner.

or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit.

cracked/damaged Technical background: Please refer to the instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged NOTE: The instructions MUST be followed to help the retailer clarify if the windscreen should be replaced under manufacturers warranty (Stress crack) or Customer pay/insurance (external influence damage)

Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference

Part Number (3W7 035 404B) - No Longer Available (NLA) and cannot be sourced or supplied Technical background In the event that subwoofer (3W7 035 404B) is required this cannot be sourced or supplied However Should the speaker (3W7 035 482B) be required, retailers can order 4W0 035 404B - The operative should then remove the speaker from 4W0 035 404B - The operative should then fit the speaker into subwoofer (3W7 035 404B)

Customer statement / workshop findings: All complaints which are related to radio reception issues Technical background: Complaints about the radio reception can have many causes. The radio reception strength/quality at the vehicle location can be an important issue. To process such complaints as effectively as possible it is important to precisely record the circumstances when a complaint occurs. The attached check list is available for this purpose. Please ensure the instructions within the Measure section are strictly adhered to

Customer statement / workshop findings: Windscreen cracked/damaged Technical background: Please refer to the instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged

instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged NOTE: The instructions MUST be followed to help the retailer clarify if the windscreen should be replaced under manufacturers warranty (Stress crack) or Customer pay/insurance (external influence damage) Measure: Identification In the event the windscreen is identified as cracked/damaged it is imperative the inspector of the cracked/damaged screen can determine if the crack was caused by external influences (stone chips) OR the screen is cracked/damaged due to a stress crack

Customer statement / workshop findings: Customers will not be aware of any DTCs, workshop operatives may discover spurious DTCs whilst running Guided Fault Finding (GFF) when using ODIS Technical background: To determine the course of action which should be taken the operative should refer to the Bentley Hub referencing the following: Spurious DTC list for TPI 2072055 The document contains all known spurious DTCs for all applicable vehicle variants.

Customer statement / workshop findings: Customers will not be aware of any fault codes Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).

Customer statement / workshop findings: -Customers will not be aware of any fault codes -Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: -The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants -Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).

Customer statement / workshop findings Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the document (loaded onto the Hub) regarding the DTC description and actions (if any) which should be conducted

-The noise/squeal can be reproduced and clearly assigned to the braking system

Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Service: Note: For correct diagnosis and repair the attached Flowchart must be followed. 1. Check the overall condition of the brakes to determine if the brake noise can be attributed to one of the causes listed in the Technical Background section of this TPI. If the noise is not a result of one these causes, proceed with point 2. 2. Record the noise and frequency For the frequency analysis and the noise recording we recommend using the Chassis Ear Tool WT 10437. To record the noise and measure the frequency using WT 10437 Chassis Ear Tool follow these instructions; Refer to File recording in the WT 10437 user instructions.

Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).

Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).

Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). 6. Discs have a groove in them (Figure 2) 7. There is chemical contamination on the braking surface of the disc due to a wheel or tyre cleaner being sprayed directly onto the disc (Figure 3). 8. There are pad marks on the brake disc as a result of the brake pad material transferring to the discs. This can occur when a vehicle has been stood for long periods of time in a wet or snowy environment (Figure 4).

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.

expected

examples in Figures 1 and 2 showing cracks within the tread pattern)

Background: -The issue is mainly evident on vehicles with very low usage This is a result of the tyre compound hardening due to the following: -Tyre age -Tyre pressure not adjusted to specification -Low mileage/vehicle usage -Vehicle storage conditions

Customer statement / workshop findings: Cracks evident in the sidewall and/or tread pattern (See the examples in Figures 1 and 2 showing cracks within the tread pattern). The issue is mainly evident on vehicles with very low usage This is a result of the tyre compound hardening due to the following: - Tyre age - Tyre pressure not adjusted to specification - Low mileage/vehicle usage - Vehicle storage conditions

Customer statement / workshop findings: In the event a customer complaint is received relating to a suspicion that control units or services have been influenced by third parties the instructions within this TPI should be followed. Technical background: A suspicion that control units or services have been influenced by third parties means that unauthorised people or groups may have gained access to a vehicle's control unit(s) or online services and may have manipulated them in such a way that may compromise customer data confidentiality or the operation of the vehicle and/or online services. When investigating potential third party influences of control units or online services, it is important to take all normal diagnostic measures to rule out a normal functional error or misuse of the system by the user

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Service: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken.

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Service: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken.

Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system

to the Technical background section of this TPI

Customer statement / workshop findings: Luggage Compartment Lid (Boot Lid) has sporadic functionality, fails to latch when closing, bounces back when closing or fails to open or close fully. Technical background: This Technical Product Information (TPI) document has been developed to resolve various boot lid concerns, it provides a series of checks and updates to ensure robust boot lid operation. It is important the TPI is followed exactly to ensure maximum benefit.