2005 Bentley Continental TSBs

up or replacing

suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

Customer statement / workshop findings: - Poor engine running - Reduced power - Engine warning lamp illuminated - Symptom related DTCs evident within the applicable engine control unit(s) Technical background: Technical Product Information (TPI) to assist retailers when diagnosing poor engine running or misfires.

engine warning lamp illuminated.

engine warning lamp illuminated.

Background: -Bentley vehicles which are applicable to this TPI are fitted with air springs as part of the suspension system. Should air leak from the air spring dampers, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. -The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air supply unit, pipes, valve unit and air reservoirs. This includes potential air leak points on the air spring dampers and also the locations of an air leak that can be repaired without the need to replace an air spring damper.

Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring.

Technical background: We have observed instances where the caps have been difficult to remove once fitted, the issue is caused by corrosion. The valve stem itself is made from aluminium and the accessory valve caps are chromium plated brass, it is possible under certain environmental conditions, particularly winter road salt, for corrosion to take place between these dissimilar metals. Measure: The solution is to apply a thin smear of silicon-based grease, such as Dow Corning high vacuum grease, to the external threads of the valve stem prior to fitting the accessory valve cap. Grease should be applied any time the cap is removed and grease is not evident

Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.

be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if any TPIs are applicable to the customers complaint/issue, should an applicable TPI be available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required) For correct diagnosis and repair, the attached Flowchart must be followed in conjunction with the Measure section of this TPI

Technical Background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfires. Service: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.

Technical Background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. Please follow and complete the check list within the Measure section of this TPI to help in diagnosing the issue (the check list does not need to be sent as an attachment should a DISS technical query be raised) . Should a leak be found from an air spring, compressor, valve unit or reservoir, please raise a DISS technical query and include as much information as possible including photograph/s of the leak/s location. Once the DISS ticket has been submitted please await clarification from your TSC before commencing with replacing any of the suspected faulty air springs. Mandatory reporting is applicable for all air spring related issues.

Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section.

Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section

parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the measure of this section of this TPI.

Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.

Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.

Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI

defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI

or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.

expected

Customer statement / workshop findings: Customers will not be aware of any DTCs, workshop operatives may discover spurious DTCs whilst running Guided Fault Finding (GFF) when using ODIS Technical background: To determine the course of action which should be taken the operative should refer to the Bentley Hub referencing the following: Spurious DTC list for TPI 2072055 The document contains all known spurious DTCs for all applicable vehicle variants.

Customer statement / workshop findings: Customers will not be aware of any fault codes Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).

Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported.

Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

findings: An improved feedback method is required should a complaint of telephone functionality / quality be reported. Technical background: A minimum standards document is required to capture an accurate description of customer telephone issues. Measure: The attached document should be completed and attached to the relevant DISS query, this will allow a full understanding of the customer complaint and the circumstances in which the complaint becomes apparent.

clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if there are any TPIs which are applicable to the customers complaint/issue if there is an applicable TPI available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required). For correct diagnosis and repair the attached Flowchart must be followed in conjunction with the Measure section of this TPI

-The noise/squeal can be reproduced and clearly assigned to the braking system

Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).

Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).

Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). 6. Discs have a groove in them (Figure 2) 7. There is chemical contamination on the braking surface of the disc due to a wheel or tyre cleaner being sprayed directly onto the disc (Figure 3). 8. There are pad marks on the brake disc as a result of the brake pad material transferring to the discs. This can occur when a vehicle has been stood for long periods of time in a wet or snowy environment (Figure 4).

changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit.

Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference

Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system

Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

Customer statement / workshop findings: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

Customer statement / workshop findings: Luggage Compartment Lid (Boot Lid) has sporadic functionality, fails to latch when closing, bounces back when closing or fails to open or close fully. Technical background: This Technical Product Information (TPI) document has been developed to resolve various boot lid concerns, it provides a series of checks and updates to ensure robust boot lid operation. It is important the TPI is followed exactly to ensure maximum benefit.

two features will no longer automatically update via GPS. Technical background: A reset to the GPS network has meant the automatic GPS date and time feature no longer functions.

to the Technical background section of this TPI