2019 Bentley Bentayga TSBs

Customer statement / workshop findings: One or a combination of the following symptoms are evident Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Customer statement / workshop findings: One or a combination of the following symptoms are evident: Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Customer statement: The customer may report an audible ticking noise from the top of the engine, low oil pressure warnings / MIL on the Driver Information Panel, and/or misfiring during engine operation

Customer statement / workshop findings: Poor engine running Reduced power Engine warning lamp illuminated Symptom related DTCs evident within the applicable engine control unit(s)

Customer statement / workshop findings: Sporadic entries in control units that use Nanotype terminals, including the airbag control unit J234, the engine control unit J623 and the emergency call and communication unit J949. These may be accompanied by intermittent electrical behaviour or repeated DTCs after earlier diagnostic checks.

Customer Statement: Customers may report that the air conditioning system blows only cold air when the engine is running. Warm air is only available after switching off the engine. The concern is commonly reported after engine removal or recent repair work.

Customer statement/Workshop findings: Emission control warning light evident within the DIP Engine not running/idling smoothly High pitched whistle from the right and left hand side of the engine TIP: Refer to video within the Bentley Hub referencing TPI 2075922/- A selection of DTCs are evident (as per TPI Event memory entries)

Customer statement / workshop findings: Engine warning lamp is illuminated within the Driver Instrument Panel (DIP) in conjunction with the DTC as detailed below. P310B00 with symptom code 2638 - Low Fuel Pressure Regulation There may also be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues in conjunction with the afore mentioned symptom/DTC

Customer statement / workshop findings: Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services.

Customer statement / workshop findings: Engine light in the DIP - Various oxygen sensor / Fuel ratio DTCs logged within the Engine Control Module (s)

overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Customer Statement: The customer may report one or more of the following after vehicle repairs: Engine does not start following workshop work Drive System Fault warning displayed in the instrument cluster (Kombi).

Customer Statement: The engine warning light comes on and the vehicle loses power.

Customers may report that the air conditioning system blows only cold air when the engine is running. Warm air is only available after switching off the engine. The concern is commonly reported after engine removal or recent repair work.

This TPI provides supplementary technical information to support diagnosis of ECM 5V reference circuit DTCs. It details the sensors associated with each reference circuit (A, B, and C) and outlines relevant guidance to assist in isolating faults when any of the following DTCs are stored in the Engine Electronics (diagnostic address: 0001)

The customer may report a ticking noise from the upper engine area, low oil pressure warnings, or a flashing MIL during engine operation.

The customer may report an audible ticking noise from the top of the engine, low oil pressure warnings / MIL on the Driver Information Panel, and/or misfiring during engine operation.

Customer statement / workshop findings: Engine warning lamp is illuminated within the Driver Instrument Panel (DIP) in conjunction with the DTC as detailed below: P310B00 with symptom code 2638 - Low Fuel Pressure Regulation There may also be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues in conjunction with the afore mentioned symptom/DTC

Condition: Sporadic entries in control units that use Nanotype terminals, including the airbag control unit J234, the engine control unit J623 and the emergency call and communication unit J949. These may be accompanied by intermittent electrical behaviour or repeated DTCs after earlier diagnostic checks.

Customer Statement: The engine warning light comes on and the vehicle loses power. Workshop Findings: Customer statement can be verified and the following entries may be logged within the engine control unit. P029900: Turbo/Super Charger Under-boost, passive/sporadic.

One or a combination of the following symptoms are evident Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Condition: One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP

Condition: Engine light in the DIP - Various Camshaft adjuster DTCs logged within the Engine Control Module(s)

Condition: Engine warning lamp is illuminated within the Driver Instrument Panel (DIP)

One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP Or Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident, in this scenario the operative should also refer to TPI 2051893/-

Technical Background: The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Condition: Poor engine running Reduced power Engine warning lamp illuminated Symptom related DTCs evident within the applicable engine control unit(s)

Technical Background: An important factor of influencing the cooling system efficiency is the water used in the mixture Due to the different ingredients and characteristics existing in each country or even region, Bentley has decided to define the quality of water for cooling systems

One or a combination of the following symptoms are evident Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP Or Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident, in this scenario the operative should also refer to TPI 2051893/-

Condition: Engine difficult to start Or Engine runs rough These issues can trigger DTC P00310B, P008A00 relating to Low Fuel Pressure regulation, Fuel pressure outside specification The following symbol can also be displayed on the Driver Instrument Panel (DIP) in conjunction with an error message start/stop unavailable

Condition: Prior to replacing the fuel delivery module or fuel pump control units please refer to the information within TPI 2077385 Engine stalling when the engine is started from cold (at idle) Or After a delayed cold start These issues can trigger DTC 310B00: Low Fuel Pressure regulation, Fuel pressure outside specification The following symbol can also be displayed on the Driver Instrument Panel (DIP) in conjunction with an error message start/stop unavailable

Condition: Water drips from the front interior light. The water drips directly from the electric drive of the front sun roof motor. Technical Background: A water drop can get onto the guide rail instead of the water flow area of the guide rail. The water runs forwards to the guide tube of the operating cable and from there onto the electric drive.

Condition: Poor engine running Reduced power Engine warning lamp illuminated Symptom related DTCs evident within the applicable engine control unit(s)

Condition: HVAC distribution/operational issues HVAC motor defect (DTCs) evident within address 08 - Climatronic control unit, the DTCs can be static or Intermittent

Condition: Torque values for ancillary components (used during engine replacement) are not currently available within the Repair manual The affected components and torque values are as listed within the Technical background section of this TPI

Condition: Engine oil level requires top up between services Technical Background: The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Condition: One or a combination of the following symptoms are evident: Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Condition: Engine oil warning lamp illuminated within the Drivers Instrument Panel (DIP) Engine oil requires topping up between services Excessive engine oil consumption

Condition: Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services.

Customer statement: Engine coolant overheat warning within the DIP

Technical Background: An important factor of influencing the cooling system efficiency is the water used in the mixture Due to the different ingredients and characteristics existing in each country or even region, Bentley has decided to define the quality of water for cooling systems Demineralised water according to standard VDE 0510 meets all requirements and can be purchased worldwide Therefore undiluted coolant should be mixed in the correct ratio using demineralised water as detailed in Elsa Pro coolant specification, this will detail the ratio and type of coolant to use The use of desalinated water in the engine cooling system is specifically prohibited

Customer statement: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) Workshop findings: DTC P304300 with symptom code (10061) - Fuel Pump Mechanical Malfunction evident

Customer statement Warning message within the DIP The message asks the customer to warm up engine accompanied by a yellow warning (Figure 1) No other symptoms are experienced. Figure 1 Workshop findings DTC P103A00 evident - Engine Oil Fuel Portion Too High (Figure 2) Figure 2

Condition: Engine management light illuminated within the DIP DTC P025C00 Fuel Pump Module Control Circuit Low is evident within 0001 (Engine control unit)

Customer statement/Workshop findings Emission control warning light evident within the DIP Engine not running/idling smoothly High pitched whistle from the right and left hand side of the engine TIP: Refer to video within the Bentley Hub referencing TPI 2075922/- A selection of DTCs are evident (as per TPI Event memory entries)

following symptoms are evident Engine overheat warning in the DIP (Engine overheating) Unusual cooling fan operation at high temperatures P19F700: Low engine coolant temperature indicator lamp coolant too warm Signs of coolant in the vacuum hoses for switch valve N649

Customer statement / workshop findings: Engine light in the DIP - Various oxygen sensor / Fuel ratio DTCs logged within the Engine Control Module(s).

Customer statement / workshop findings: Engine light in the DIP - Various Camshaft adjuster DTCs logged within the Engine Control Module(s).

Customer statement / workshop findings: DTC P218100 - Cooling System Performance and / or DTC P1BB400 Cylinder head temperature too low is stored in the Engine Control Module (ECM). Emission Control Lamp illuminated on the Driver Instrument Panel.

Customer statement: Engine coolant overheat warning within the DIP

Technical background It is possible for the engine coolant Thermostat to corrode over time, this corrosion is due to an adverse reaction of the Thermostat material with the engine coolant. The corrosion and subsequent build-up of debris prevents the correct operation of the thermostat when closing, resulting in over cooling. The ECM triggers a DTC when the target engine temperature is outside of the specified parameter.

Customer statement / workshop findings: One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP Or Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident, in this scenario the operative should also refer to TPI 2051893

Customer statement / workshop findings: One or a combination of the following is evident: Coolant leaking from the mechanical coolant pump Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump Low coolant level warning displayed within the DIP Or Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident in this scenario the operative should refer to TPI 2051893/-

Customer statement / workshop findings - Engine warning lamp illuminated within the Driver Instrument Panel (DIP) - DTC P227900 is evident within Engine control unit 0001 in conjunction with DTC P030000 - Whistle noise may also be evident from the engine.

Customer statement / workshop findings: - Customer reports an engine overheat warning within the DIP - Engine overheating - Unusual cooling fan operation at high temperatures - There are no obvious signs of coolant leaks both internally or externally Workshop findings - P19F700: Low engine coolant temperature indicator lamp Coolant too warm - Signs of coolant in the vacuum hoses (Refer to the video on the Bentley Hub referencing TPI 2061369.

Customer statement / workshop findings: Emission control system warning light illuminated within the DIP. Workshop findings: DTC P04F000 EVAP system high pressure purge line performance DTC evident within the engine control unit Technical background: The DTC is related to mismatched terminal locations of the Pressure sensor for the activated charcoal filter system G804.

Customer statement / workshop findings: - Engine warning lamp illuminated within the Driver Instrument Panel (DIP) - DTC P227900 is evident within Engine control unit 0001 in conjunction with DTC P030000 - Whistle noise may also be evident from the engine.

up or replacing

light illuminated within the DIP -DTC P025C00 Fuel Pump Module Control Circuit Low is evident within 0001

Engine lubricating oil requires topping up between services.

suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

Customer statement / workshop findings One or a combination of the following is evident: - Coolant leaking from the mechanical coolant pump - Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump - Low coolant level warning displayed within the DIP Or - Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident, in this scenario the operative should also refer to TPI 2051893

Customer statement / workshop findings: One or a combination of the following is evident: - Coolant leaking from the mechanical coolant pump - Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump - Low coolant level warning displayed within the DIP Or - Engine overheating issues and/or DTC P218100: Cooling System Performance with symptom code 8113 or air in the coolant DTCs (various) is evident in this scenario the operative should refer to TPI 2051893.

Customer statement / workshop findings: - Poor engine running - Reduced power - Engine warning lamp illuminated - Symptom related DTCs evident within the applicable engine control unit(s) Technical background: Technical Product Information (TPI) to assist retailers when diagnosing poor engine running or misfires.

and should be applied to the following control units: -Engine control unit -transmission control unit

illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below:

Statement: -Check Engine Lamp illuminated within the Driver Instrument Panel (DIP)

the Driver Instrument Panel -The time to reach the correct engine coolant operating temperature has increased

DIP message -The message asks the customer to (warm up engine) accompanied by a yellow warning. No other symptoms are experienced.

P11DE00 logged (Cam Shift Actuator Outlet (B) Cylinder 6 Range/Performance)

within the DIP -Engine overheating -Unusual cooling fan operation at high temperatures -There are no obvious signs of coolant leaks both internally or externally Workshop Findings: -P19F700: Low engine coolant temperature indicator lamp coolant too warm -Signs of coolant in the vacuum hoses

Customer Statement: -Coolant leaking from the mechanical coolant pump -Coolant witness marks on the mechanical coolant pump although coolant is not leaking/dripping from the pump -Low coolant level warning displayed within the DIP -Engine Overheating issues and/or DTC P218100: Cooling System Performance with Symptom Code 8113

started from cold (at idle) -Or After a delayed cold start

Statement: -Check engine lamp illuminated within the Driver Instrument Panel (DIP)

Engine warning lamp is illuminated within the Driver Instrument Panel (DIP) in conjunction with the DTC as detailed below:

Technical Background: -Air intake leak due to a broken one-way diaphragm valve from within the Bank 1 breather line

Findings: -Various/numerous open circuit DTCs evident within the engine control unit -Fuse 6 (SA fuseboard) in some cases could be blown

instrument panel as shown in figure 1 and event code P15AA00 is evident in one or both of the engine control modules

the brake pedal clicking shortly after vehicle start up/drive away (following engine start) once the vehicle reaches 20kmh/12mph

Findings: -Coolant leaking from the mechanical coolant pump -Coolant witness mark on the mechanical coolant pump although coolant is not leaking/dripping from the pump -Low coolant level warning displayed

displayed, engine misfire Workshop Findings: -Event entries in engine control unit relating to cylinder misfires- excessive carbon build up to leading to cylinder leakage and spark plug foul

evident within the DIP

-The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances.

engine warning lamp illuminated.

illuminated within the Driver Information Panel (DIP) in conjunction with DTC - P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow - logged within on or both engine control modules

-The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. -The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type -Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering.

engine warning lamp illuminated.

Statement: -Engine warning lamp is illuminated within the driver instrument panel (DIP) in conjunction with the DTC.

Illuminated within the Driver Instrument Panel (DIP): -P310B00 with system code 2636 - Low Fuel Pressure Regulation" Low Fuel Pressure Regulation" -P014800 Fuel Deliver Error" -P019100 Fuel Rail Pressure Sensor 'A' Circuit Range/Performance -P018B00 Fuel Pressure Sensor "B" Circuit Range/Performance with symptom code 17871 -Misfire" DTCs

Statement: -Engine warning lamp is illuminated within the Driver Instrument Panel (DIP) in conjunction with the DTC as detailed below: P310B00 with symptom code 2638 - Low Fuel Pressure Regulation There may also be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues in conjunction with the afore mentioned symptom/DTC Technical Background: -NOTE: The retailer must attempt to request as much information as possible regarding when the issue occurred Pre-conditions, For example: -Driving at low speed in traffic -Warning lights -Driveability at the time the issue occurred - During idle or driving? -If during idle, how long had the car been idling? -Details when the vehicle was last refuelled and the grade of fuel used -When the issue occurred, How was the car unlocked and started? Keyless entry or entry by using the remote key fob

Customer statement / workshop findings Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) in conjunction with the DTC as detailed below: - P310B00 with symptom code 2638 - Low Fuel Pressure Regulation There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues Technical background In the event the customer complaint relates to the following: - Customer experienced poor start up or the engine stalled shortly after start up - proceed with the remaining instructions NOTE: The operative must gather information regarding the Customer experience regarding when the issue occurred for example: Pre- conditions, warning lights and driveability at time issue occurred, details when the vehicle was last refuelled and the grade of fuel used The operative must now use the information contained within the Measure section to determine the correct analysis and repair procedure.

Customer statement / workshop findings: Squeal from the rear of the vehicle at low speed while braking. Technical background: While braking at low speed, a vibration of 1.2 to 1.4 KHz can be produced by the friction between the rear brake pad and disc resulting in a complaint of brake noise from the customer. Measure: 1) Follow the Brake noise identification TPI 2052785 - IMPORTANT: For frequency analysis the noise recording equipment Bentley Motors recommends is the Chassis ear tool WT 10437 2) If the sound recording produces a frequency of 1.2-1.4KHz - Remove the rear brake pads as per Repair manual Rep.Gr 46 - Rear Brake Pads - To Remove and Fit and check the actual condition of the brake pads - If the brake pads are to be refitted it will be necessary to make note of the position of the pads for installation purposes

Customer statement: - MIL light displayed - Engine not refined when running Workshop findings The two most common DTCs are as follows: - P032700 - Knock sensor 2 Circuit Low input - address 01 (Engine control module 1) - P033200 - Knock sensor 1 Circuit Low input - address 01 (Engine control module 1) Technical background: In the event the symptoms and/or DTCs are evident the operative should refer to the instructions within the Measure section.

Customer statement / workshop findings: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: -P310B00 with symptom code 2636 - Low Fuel Pressure Regulation Low Fuel Pressure Regulation -P014800 Fuel Deliver Error -P019100 Fuel Rail pressure Sensor A Circuit Range/Performance Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues, Measure: Check Engine Lamp Illumination with DTC P310B00 and symptom code 2636 - Engine Running Concerns, Fuel system issues -P310B00 Low Fuel Pressure Regulation symptom code 2636 -P014800 Fuel Deliver Error -P019100 Fuel Rail pressure Sensor A Circuit Range/Performance Misfire DTCs 1) If not already done, raise a DISS query. 2) Check Low fuel pressure, specified value and Fuel low pressure, actual value within the fault memory, refer to ECU 01 Engine Control Module 1 - From Extended ambient conditions note the values of the Low fuel pressure, specified value and Fuel low pressure, actual value as shown in Figure 1.

Customer Statement: Emission control system warning light illuminated within the DIP (Figure 1) Figure 1 Workshop findings DTC P245000 - EVAP System Switching Valve "A" Performance/Stuck Open - With symptom code 11952. Measure: Fuel System vapours are extremely flammable. Please refer to the Repair manual "Fuel system - Safety precautions" before commencing with any fuel system procedures 1) Referring to the applicable wiring diagram conduct a wiring integrity check of the Leak Detection Pump wiring circuit and connectors 2) Perform a smoke test of the leak detection system - Monitor for any leaks 3) If no faults were found - Refer to Rep.Gr 20 - Replace the leak detection pump (V144) 4) Inspect the LDP for impact damage when extracted, the operative must provide feedback and photographic evidence (see example shown in Figure 2) via a new or existing DISS query

Customer statement / workshop findings: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) in conjunction with the DTC as detailed below: - P310B00 with symptom code 2638 - Low Fuel Pressure Regulation There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues. Measure: Check Engine Lamp Illumination with DTC P310B00 and symptom code 2638 1) For vehicles that only have the symptoms: - Check Engine Lamp Illumination with DTC P310B00 and symptom code 2638 with an Adaption of Fuel Pump (FP) figure of minus 100 to minus 200 kPa Figure 1 - the Fuel Delivery Module within the fuel tank should be replaced Figure 2 - Refer to Repair Group 20 Fuel supply, gas operation / 4.0L V8 TSI / Fuel pump, fuel level sensors, and jet pump (RH) To remove and fit.

Customer statement / workshop findings: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: - P310B00 with symptom code 2636 - Low Fuel Pressure Regulation Low Fuel Pressure Regulation - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues. Measure: Check Engine Lamp Illumination with DTC P310B00 and symptom code 2636 - Engine Running Concerns, Fuel system issues - P310B00 Low Fuel Pressure Regulation symptom code 2636 - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - Misfire DTCs 1) If not already done, raise a DISS query. 2) Check Low fuel pressure, specified value and Fuel low pressure, actual value within the fault memory, refer to ECU 01 Engine Control Module 1 - From Extended ambient conditions note the values of the Low fuel pressure, specified value and Fuel low pressure, actual value as shown in Figure 1.

Workshop findings: - Coolant leaking from the mechanical coolant pump And/or - Low coolant level warning displayed Technical background: The operative MUST ensure the instructions within the Measure section are followed, the instructions differ slightly depending on the part number of the mechanical coolant pump (B or C suffix).

Customer statement / workshop findings: - Emission control warning within the DIP And/or - Whistling noise(s) from the Inlet manifold Workshop findings: Oil leak between the oil separator tank and the Bank 1 breather line connection (Figure 1) NOTE: Oil leak detection spray is evident within Figure1, the use of detection spray in the example shown highlights the location of the leak. Measure: 1) Referring to Rep.Gr 17 - Gain access to the oil separator tank 2) Referring to Figure 2 - Replace the following parts and all associated parts as detailed within the applicable Rep.Gr and the ETKA parts catalogue

Customer statement / workshop findings - Engine misfiring - Engine running rough (not refined) - Engine misfire DTCs evident - Engine management light illuminated within the DIP - Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) Measure VERY IMPORTANT: Before continuing with the onward instructions the operative should confirm if the following VIN applicable Service Campaign is listed within Elsa pro - EC24 - V8 Kovomo - New Continental GT/GTC and New Flying Spur - Valve spring replacement (SC21/41) Or - EC25 - V8 Kovomo - Bentayga - Valve spring replacement (SC21/42)

Customer statement / workshop findings: - Engine misfiring - Engine running rough (not refined) - Engine misfire DTCs evident - Engine management light illuminated within the DIP - Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) IMPORTANT: The symptoms described are typically evident during early life stages of vehicle use (between 100Km and 250Km) Technical background Refer to the Measure section of this TPI in the event the symptoms are as described

Customer statement - MIL light displayed - Engine not refined when running Workshop findings The two most common DTCs are as follows: - P032700 - Knock sensor 2 Circuit Low input - address 01 (Engine control module 1) - P033200 - Knock sensor 1 Circuit Low input - address 01 (Engine control module 1) Please note: The DTCs listed are the two most common DTCs (seen to date) although other DTCs may be evident depending on the failure mode (including the boost control solenoid and crankcase ventilation heater DTCs)

Customer statement / workshop findings: Torque values for ancillary components (used during engine replacement) are not currently available within the Repair manual. The affected components and torque values are as listed within the Technical background section of this TPI. Measure: Refer to the Technical background section

Customer statement / workshop findings: Air suspension warning light within the DIP Workshop findings: One or a combination of the DTCs shown below are evident within address 74 - P089200 - Symptom Code 3145792 - TCM Power Relay Sense Circuit Intermittent (Level Control Valves Open Circuit) - C103B13 - 3145909 - Solenoid for level control system Open circuit - C104707 - 3211279 - Level control valves mechanical malfunction Technical background: Refer to the Measure section of this TPI

Customer statement / workshop findings: Air suspension system warning displayed in the Driver Instrument Panel (DIP) Workshop findings DTC C11C613 (Symptom Code 3145826) - Valve for rapid filling of air suspension Open circuit stored in the Chassis control unit (Address 74) Technical background: In the event that the afore mentioned symptom(s) are evident please refer to the instructions within the Measure section of this TPI.

evident -Engine management light illuminated within the DIP -Knocking noise from the cylinder head (NOTE: The noise can be evident on either bank) IMPORTANT: The symptoms described are typically evident during early life stages of vehicle use (between 100Km and 250Km)

activation/ deactivation solenoid fixings -Or Fuel rail fixings -Or Fixings for the vacuum system assembly Technical background: Shows oil leaked which had leaked from the tell tale hole at the top of the fixing. Upgraded fixings prevent oil leaks from the tell hole.

Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. The Measure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring.

Customer statement / workshop findings: Emission control system warning lamp illuminated (Figure 1) within the Driver Information Panel (DIP) in conjunction with DTC - P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow - logged within one or both engine control modules. Technical background: Should DTC P044100: EVAP Emission Contr.Sys.Incorrect Purge Flow be evident (static or intermittent) within one or both Engine control modules please refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings Workshop findings: Buzzing noise heard at idle from the sump area when the vehicle is elevated on a workshop ramp. The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances. Technical background: A buzzing noise can be generated by the oil pump when the engine is running at idle. Measure: Test a comparable vehicle with the same Engine derivative. If the same noise is apparent on the comparable vehicle and no oil pressure warnings or relevant DTCs are stored then the noise can be considered a characteristic of the vehicle and no further action should be taken.

Customer statement / workshop findings Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services. Technical background: In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified running-in periods consume more oil during the running-in period, and the oil consumption will stabilize after the running-in period. Refer to the Owners Manual for specific running-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Certain driving conditions may negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods

illuminated on Driver Instrument Panel. The time to reach the correct engine coolant operating temperature has increased. Diagnostic Trouble Code(DTC) P218100 -Cooling System Performance is stored in the Engine Control Module (ECM), the vehicle warm up time is longer when compared to other vehicles of the same type. Technical background: It is possible for the engine coolant Thermostat to corrode overtime, this corrosion is due to an adverse reaction of the Thermostat material with the engine coolant. The corrosion and subsequent build-up of debris prevents the correct operation of the thermostat when closing, resulting in over cooling. The ECM triggers a DTC when the target engine temperature is outside of the specified parameter.

statement: Engine warning light and max engine speed 4000 rpm warning evident within the DIP during acceleration - Warning on DIP first appears when accelerating (During boost) Workshop findings: DTC P029900 evident within the engine control unit/s In the event the afore mentioned symptoms are evident the operative should refer to the onward instructions

Customer statement / workshop findings: Ticking noise emanating from rear of Bank 1 cylinder head Technical background: Noise from failed vacuum pump. Measure: A specific vacuum pump failure is known to create a ticking noise. This ticking noise, on initial inspection, is easily misinterpreted as a fault in the valve train or fuel injector, when in reality it is more likely to be produced by a defective vacuum pump. Therefore always ensure that this type of noise is identified precisely using a stethoscope. Specifically use the stethoscope to check the vacuum pump located at the rear of Bank 1 cylinder head, when this is found to be the origin of the noise then change the vacuum pump and retest.

Customer statement / workshop findings: Customer statement: Emission control warning signal displayed, engine misfire Workshop findings: Event entries in engine control unit relating to cylinder misfires excessive carbon build up to leading to cylinder leakage and spark plug foul. Technical background: Deviations in the country-specific fuel specifications can lead to carbon deposits on the injectors. If pronounced these deposits can lead to spark plug fouling, cylinder leakage and fouled injectors all influencing combustion in the cylinder. As a result the above event entries are logged in the engine control unit. Measure: - Follow the Misfire best practice TPI 2051187 in order to confirm that the root cause of the misfire is excessive cylinder carbonisation leading to excessive cylinder leakage/fouling

Technical background: We have observed instances where the caps have been difficult to remove once fitted, the issue is caused by corrosion. The valve stem itself is made from aluminium and the accessory valve caps are chromium plated brass, it is possible under certain environmental conditions, particularly winter road salt, for corrosion to take place between these dissimilar metals. Measure: The solution is to apply a thin smear of silicon-based grease, such as Dow Corning high vacuum grease, to the external threads of the valve stem prior to fitting the accessory valve cap. Grease should be applied any time the cap is removed and grease is not evident

Customer statement / workshop findings: Engine oil level requires top up between services Technical background: The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Customer statement / workshop findings: Complaint of the brake pedal clicking shortly after vehicle start up/drive away (following engine start) once the vehicle reaches 20kmh/12mph Technical background: Refer to the video on the Bentley Hub referencing TPI 2064404/- The noise is the ABS control unit performing a self-test diagnostic routine If the complaint noise is as shown in the video, the customer should be advised that this is normal and expected behaviour

Customer statement / workshop findings: Customer reporting Emission Control Warning Indicator displayed. Engine running rough.

Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.

Customer statement / workshop findings At low speed, during low braking force application, the rear brakes can produce a high frequency noise (5khz). Measure 1) Follow the Brake noise identification TPI 2052785 - IMPORTANT: For frequency analysis the noise recording equipment Bentley Motors recommends is the Chassis ear tool WT 10437 - Obtain a clear recording using WT 10437 - Carry out an inspection of the brake system to confirm the brake system components are serviceable as per Elsa pro guidelines - Confirm if the brake shim kit (36A 698 219) has previously been fitted to the rear brake pads (As per TPI 2046299/-)

Customer statement / workshop findings: Engine stalling when the engine is started from cold (at idle) Or after a delayed cold start. These issues can trigger DTC 310B00: Low Fuel Pressure regulation, Fuel pressure outside specification The following symbol can also be displayed on the Driver Instrument Panel (DIP) in conjunction with an error message start/stop unavailable

Customer statement / workshop findings: Prior to replacing the fuel delivery module or fuel pump control units please refer to the information within this TPI This TPI is applicable for W12 Bentayga TSI engine variants only Technical background: The twin fuel pumps which are part of the fuel delivery module (located on the right hand side of the fuel tank as Figure 1) have changed to an improved Diamond Like Coated (DLC) fuel pump.

Customer statement / workshop findings Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: - P310B00 with symptom code 2636 - Low Fuel Pressure Regulation Low Fuel Pressure Regulation - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues Technical background In the event the customer complaint relates to the following: - Customer experienced poor start up - proceed with the remaining instructions

Customer Statement: Emission control system warning light illuminated within the DIP (Figure 1). Workshop findings: DTC P245000 - EVAP System Switching Valve A Performance/Stuck Open - With symptom code 11952 Technical background: Refer to the Measure section of this TPI

Customer statement / workshop findings: Erratic whining noises from the front of the engine at idle speed. Workshop findings: The irregular knocking noises can be assigned to the front of the engine. There are no further complaints (such as poor engine or engine cooling system performance, event entries, etc.) Technical background: Refer to the video on the Bentley hub referencing TPI 2063354/- In the event the whining noise is as within the video, please refer to the Measure section of this TPI

Customer statement / workshop findings: Vehicle vibration / humming noise at idle. Technical background: Right hand Active Engine Mount (AEM) failed, oil may also be leaking from the AEM (Figure 1). This failure mode is only seen on W12 engine installations and is only apparent at idle.

Customer statement / workshop findings The following Static DTCs are evident following the fitment of replacement Active engine mounts and/or the Active Engine mount control unit (00BA) with the part number 4M0907145E with SW 0132 (often as result of TPI 2060418/-) C113107: Actuator 1 for assembly mounting mechanical malfunction Symptom Code 784 And/or C113207: Actuator 2 for assembly mounting mechanical malfunction Symptom Code 785 Technical background Refer to the Measure section of this TPI

Customer statement / workshop findings At low speed, during low braking force application, the rear brakes can produce a high frequency noise (5khz). Measure 1) Follow the Brake noise identification TPI 2052785 - IMPORTANT: For frequency analysis the noise recording equipment Bentley Motors recommends is the Chassis ear tool WT 10437 - Obtain a clear recording using WT 10437 2) Carry out an inspection of the brake system to confirm the brake system components are serviceable as per Elsa pro guidelines 3) Confirm if the brake shim kit (36A 698 219) has previously been fitted to the rear brake pads (As per TPI 2046299/-)

engine overheat warning on the DIP - Engine overheats - Unusual cooling fan operation at high temperatures - There are no signs of coolant leaks both internally or externally Technical background: To heat the engine as quickly as possible during cold starting, delivery of coolant from the coolant pump is interrupted in the warm-up phase by the solenoid valve for the mechanical coolant pump

Customer statement / workshop findings: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: - P310B00 with symptom code 2636 - Low Fuel Pressure Regulation Low Fuel Pressure Regulation - P014800 Fuel Deliver Error - P019100 Fuel Rail pressure Sensor A Circuit Range/Performance - Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues. Technical background: In the event the customer complaint relates to the following: Customer experienced poor start up - proceed with the remaining instructions NOTE: The operative must gather information regarding the Customer experience regarding when the issue occurred for example: Pre- conditions, warning lights and driveability at the time that the issue occurred, details when the vehicle was last refuelled and the grade of fuel used The operative must now use the information contained within the Measure section to determine the correct analysis and repair procedure

Customer statement / workshop findings: Water drips from the front interior light. The water drips directly from the electric drive of the front sun roof motor. Technical background: A water drop can get onto the guide rail instead of the water flow area of the guide rail. The water runs forwards to the guide tube of the operating cable and from there onto the electric drive.

Customer statement / workshop findings: Prior to replacing the fuel delivery module or fuel pump control units please refer to the information within this TPI. This TPI is applicable for W12 Bentayga TSI engine variants only. Technical background: The twin fuel pumps which are part of the fuel delivery module (located on the right hand side of the fuel tank as Figure 1) have changed to an improved Diamond Like Coated (DLC) fuel pump.

Customer statement / workshop findings: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) in conjunction with the DTC as detailed below: - P310B00 with symptom code 2638 - Low Fuel Pressure Regulation There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues Technical background: In the event the customer complaint relates to the following: - Customer experienced poor start up or the engine stalled shortly after start up proceed with the remaining instructions NOTE: The operative must gather information regarding the Customer experience regarding when the issue occurred for example: Pre- conditions, warning lights and driveability at time issue occurred, details when the vehicle was last refuelled and the grade of fuel used The operative must now use the information contained within the Measure section to determine the correct analysis and repair procedure

statement: Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) Workshop findings: DTC P304300 with symptom code (10061) - Fuel Pump Mechanical Malfunction evident Technical background: Refer to the Measure section of this TPI

Customer statement: Air suspension warning light within the DIP Workshop findings: P089200 Symptom Code 3145792 - TCM Power Relay Sense Circuit Intermittent (Level Control Valves Open Circuit) Technical background: Refer to the Measure section of this TPI.

Customer statement / workshop findings Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: P310B00 Low Fuel Pressure Regulation. P014800 Fuel Deliver Error. P019100 Fuel Rail pressure Sensor Circuit Range/Performance. Misfire DTC. There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues

Customer statement / workshop findings: -Customer reports an engine overheat warning on the DIP -Engine overheats -Unusual cooling fan operation at high temperatures -There are no signs of coolant leaks both internally or externally Technical background: To heat the engine as quickly as possible during cold starting, delivery of coolant by the coolant pump is interrupted in the warm-up phase by the solenoid for the mechanical coolant pump. The solenoid is designed to cut off the vacuum supply to the coolant pump when the engine reaches the maximum temperature, the vacuum cut off allows the engine to start circulating coolant by retracting a sleeve which is situated around the coolant pump impeller. When the solenoid is at fault (sticking open) the vacuum supply is constant, this allows the sleeve to stay in position around the impellor which leads to the symptoms described within the Customer statement/Workshop findings section of this TPI.

Customer statement / workshop findings Check Engine Lamp illuminated within the Driver Instrument Panel (DIP) with one or multiple DTCs as detailed below: P310B00 Low Fuel Pressure Regulation P014800 Fuel Deliver Error P019100 Fuel Rail pressure Sensor Circuit Range/Performance Misfire DTCs There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues

Customer statement / workshop findings. Customer statement: Buzzing/vibrating/grinding noise can be heard from the front of the engine, mainly from cold start at idle Workshop findings Noise emitting from the air conditioning belt idler (Figure 1 Point A) Technical background: Should the noise be evident from the air conditioning belt idler - Refer to the Measure section of this TPI The operative must confirm the noise is not from any other components for example the alternator belt tensioner before conducting the instructions within the Measure section of this TPI.

Customer statement / workshop findings: Buzzing/vibrating/grinding noise can be heard from the front of the engine, mainly from cold start at idle Workshop findings Noise emitting from the air conditioning belt idler (Figure 1 Point A) Technical background: Should the noise be evident from the air conditioning belt idler - Refer to the Measure section of this TPI

Customer statement / workshop findings: Whining noise can be heard from the front of the engine Workshop findings Oil leaking from the Alternator belt tensioner Technical background: Should oil be evident on the alternator belt tensioner, refer to the Measure section of this TPI

Customer statement/workshop findings: HVAC operation issue and HVAC motor defect (DTCs) evident within address 08 Climatronic control unit, the DTCs can be static or sporadic, for example: B108D09: Right temperature flap positioning motor - Component defect Technical background: The HVAC motor/s can become jammed causing HVAC operation issues.

Customer statement / workshop findings Workshop findings: Buzzing noise heard at idle from the sump area when the vehicle is elevated on a workshop ramp. The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances. Technical background: A buzzing noise can be generated by the oil pump when the engine is running at idle.

Customer statement / workshop findings: Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services. Technical background: In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified running-in periods consume more oil during the running-in period, and the oil consumption will stabilize after the running-in period. Refer to the Owners Manual for specific running-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Certain driving conditions may negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

Customer statement/workshop findings: Ticking noise emanating from rear of Bank 1 cylinder head Technical background: Noise from failed vacuum pump

to corrode over time, this corrosion is due to an adverse reaction of the Thermostat material with the engine coolant. The corrosion and subsequent build-up of debris prevents the correct operation of the thermostat when closing, resulting in over cooling. The ECM triggers a DTC when the target engine temperature is outside of the specified parameter

Customer statement / workshop findings Check Engine Lamp illuminated on Driver Instrument Panel (DIP) Diagnostic Trouble Code (DTC) P310B00 Low Fuel Pressure Regulation stored in the Engine Control Unit. DTC P014800 Fuel Delivery Error stored in the Engine Control Unit. Misfire DTC stored in the Engine Control Unit. Technical background There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues, use the information contained within the Measure section to determine the correct analysis and repair procedure.

Customer statement / workshop findings Vehicle vibration / humming noise at idle Technical background Right hand Active Engine Mount (AEM) failed, oil may also be leaking from the AEM (Figure 1). This failure mode is only seen on W12 engine installations and is only apparent at idle. Current software is incompatible with AEM part numbers 4M0 199 255/6 BH. When the AEMs are replaced with the above part numbers, the AEM control module must be reprogrammed or replaced as detailed within the onward instructions

when the vehicle is elevated on a workshop ramp. The noise cannot be heard from inside the cabin or outside of the vehicle in normal circumstances. Technical background: A buzzing noise can be generated by the oil pump when the engine is running at idle.

Customer statement/workshop findings: Customer statement: Emission control warning signal displayed, engine misfire Workshop findings: Event entries in engine control unit relating to cylinder misfires excessive carbon build up to leading to cylinder leakage and spark plug foul Technical background: Deviations in the country-specific fuel specifications can lead to carbon deposits on the injectors. If pronounced these deposits can lead to spark plug fouling, cylinder leakage and fouled injectors all influencing combustion in the cylinder. As a result the above event entries are logged in the engine control unit

Customer statement/workshop findings: Slow operation of the left and/or right hand front window lift motor Technical background: Refer to the checks within the Measure section before replacing a front window lift motor The checks within the Measure section are imperative as some motors which have been returned to Bentley Motors exhibit no faults, therefore the issue may not be the motor.

Customer statement/workshop findings Floor pan or steering column/steering wheel vibration when manoeuvring/steering at slow speeds with steering wheel input Technical background Prior to carrying out the assessments within the Measure section, the retailer must check and confirm the following: The engine has not been chip tuned The vehicle is in standard condition (as per factory specification) ensuring that NO non approved accessories are fitted The suspension, steering and brake components are in a serviceable condition The engine, transmission mounts, powertrain and all wheel bearings are in a serviceable condition The exhaust system and all wheels and tyres are in a serviceable condition (as per factory specification) Once confirmed that all the afore mentioned criteria has been met the assessment can then be conducted

Customer statement / workshop findings: Emission Control Lamp illuminated on Driver Instrument Panel. The time to reach the correct engine coolant operating temperature has increased. Diagnostic Trouble Code (DTC) P218100 - Cooling System Performance is stored in the Engine Control Module (ECM), the vehicle warm up time is longer when compared to other vehicles of the same type. Technical background: It is possible for the engine coolant Thermostat to corrode over time, this corrosion is due to an adverse reaction of the Thermostat material with the engine coolant. The corrosion and subsequent build-up of debris prevents the correct operation of the thermostat when closing, resulting in over cooling. The ECM triggers a DTC when the target engine temperature is outside of the specified parameter.

Customer statement / workshop findings: Engine oil level requires to:p up between services. Technical background The use of the correct oil for each engine type is critical for its continued performance, reliability and ultimately warranty. The workshop manual should always be the first point of reference, ensuring the correct lubricant is used for each specific model year and engine type Should oil be required the parts catalogue must be referred to ensuring the correct VIN is always used when ordering

Customer statement / workshop findings: The front and/or rear suspension appears to have dropped. Technical background: The list of Bentley vehicles below are fitted with air springs as part of the suspension system. Should air leak from the air springs, this will cause the suspension to drop. However, the dropping of the suspension does not necessarily mean that the air spring is faulty. TheMeasure section of this TPI describes how and where to check for air leaks on the front and rear air springs, the air pump compressor, pipes, valve unit and air reservoirs. This includes potential air leak points on the air springs and also the locations of an air leak that can be repaired without the need to replace an air spring. These checks should be carried out in conjunction with the Elsapro procedure Air suspension: To check with the use of the special tool Air suspension leak tester VAS 751 001 shown in the image below as item ( 1). Refer to Elsapro, Repair Group 43, Air suspension To check.

Customer statement/Workshop findings: Emission control warning light evident within the DIP (Figure 1) Engine not running/idling smoothly High pitched whistle from the right hand side of the engine TIP: Refer to video within the Bentley Hub referencing TPI 2059379/- A selection of DTCs are evident (as per TPI Event memory entries) Technical Background: Air intake leak due to a broken one-way diaphragm valve from within the Bank 1 breather line

Customer statement / workshop findings: HVAC operation issue and HVAC motor defect (DTCs) evident within address 08 Climatronic control unit, the DTC/s can be static or sporadic, for example: B108D09: Right temperature flap positioning motor - Component defect Technical background: The HVAC motor/s can become jammed causing HVAC operation issues.

Customer statement / workshop findings: Engine lubricating oil lamp illuminated on driver instrument panel. Engine lubricating oil requires topping up between services. Technical background: In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified running-in periods consume more oil during the running-in period, and the oil consumption will stabilize after the running-in period. Refer to the Owners Manual for specific running-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Certain driving conditions may negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

control module Bentayga Software update required to the transmission control module Please ensure the operative uses the applicable SVM code for the correct vehicle type Remedy: Software update required for the applicable control modules depending on vehicle type

Trouble Code (DTC) P310B00 Low Fuel Pressure Regulation stored in the Engine Control Unit (ECU). DTC P014800 Fuel Delivery Error stored in the ECU. Misfire DTC stored in the ECU. Technical background: There may be multiple DTCs and symptoms present due to fuel pressure regulation or fuel supply issues, use the information contained within the Measure section to determine the correct analysis and repair procedure.

Customer Statement Emission control system warning light illuminated within the DIP (Figure 1) Workshop findings DTC P04F000 EVAP system high pressure purge line performance DTC evident within the engine control unit Technical background The DTC is related to mismatched terminal locations of the Pressure sensor for the activated charcoal filter system G804 (Figure 2)

gear selected Technical Background: Due to legal requirements, changes have been made to the visibility of guidelines in the Top view and Rear view camera systems on all vehicles built from May 2018 in the following regions: USA Canada Mexico Puerto Rico On the Top view camera system the guidelines are not visible on first reverse gear selection after engine start, the guidelines are visible on the second selection and thereon after. If the PDC button is pressed the guidelines are always visible. On the Rear view camera system the guidelines are never visible.

be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted including the modification of the engine control modules (chip tuning) Check the history of the vehicle to confirm Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if any TPIs are applicable to the customers complaint/issue, should an applicable TPI be available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required) For correct diagnosis and repair, the attached Flowchart must be followed in conjunction with the Measure section of this TPI

Technical Background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfires. Service: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.

background: Refer to the checks within the Measure section before replacing a front window lift motor The checks within the Measure section are imperative as some motors which have been returned to Bentley Motors exhibit no faults, therefore the issue may not be the motor.

must be carried out when the active engine mounts are replaced with Part number 4M0 199 255/6 BH. Technical background: Current software is incompatible with active engine mounts part numbers 4M0 199 255/6 BH. When the active engine mounts are replaced with the above part numbers, the active engine mount control module must be reprogrammed or replaced.

Customer Statement: Airflow from the organ stops (air regulators) is not functioning correctly; vents may be stuck, broken, or showing incorrect operation.

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP)

Technical background If an issue is suspected for one of the control modules listed below: Onboard supply control unit (J519) Convenience system central control unit (J393) Data bus diagnostics interface (J533) Control unit 1 for Information Electronics (J794) Control unit in dash panel insert (J285) Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query.

Customer statement / workshop findings: 12 volt battery flat or unserviceable

Customer statement / workshop findings: 12 volt battery flat or unserviceable

Condition: 12 volt battery flat or unserviceable

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP)

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP)

Technical Background The root cause of Exhaust Flap Control Unit malfunction is electrical shorting of the commutator segments, this is caused by an accumulation of Sludge within the exhaust flap control unit DTCs are stored when the respective Control Unit does not move through its full range of motion.

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP)

Customer statement / workshop findings: Keyless entry system (KESSY) function is disabled when the vehicle is parked for a short duration of time Technical background: The reported symptom is due to the Battery management shut off stages being too early due to the battery size being incorrectly entered on replacement

Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP) Workshop findings: DTC P0B2500 - Hybrid/EV Battery "A" Voltage low is stored within address 21- Battery Energy Control Module 2 Technical background: Possible internal fault with the super capacitor

Customer statement: Night vision warning lamp (Figure 1) is evident with the Drivers Information Panel (DIP). Workshop findings: DTC - B2000F2: Faulty control module (Symptom code 4102) evident within address 0084 - Night vision control module.

Customer statement / workshop findings Customer statement: Bentley dynamic ride system fault is displayed within the Drivers Instrument Panel (DIP) Workshop findings: DTC P0B2500 - Hybrid/EV Battery "A" Voltage low is stored within address 21- Battery Energy Control Module 2 Technical background: Possible internal fault with the super capacitor

Workshop findings The following DTCs could also be evident within diagnostic address 0046 and/or 00BB and/or 00BC B131DF5: alarm system siren supply voltage lower limit value less than B131D29: sirens / alarm horn for anti-theft warning system Range/Performance B131D29: anti-theft alarm system siren / alarm horn signal, not valid

Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section.

Customer statement / workshop findings: 12 volt battery flat or unserviceable Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim refer to the instructions within the Measure section

Customer statement: Incorrect rear seatbelt buckle status shown within the DIP Workshop findings: Although there is no occupant evident within the rear seats (2nd row) the rear seat is shown as occupied (Figure 1). Technical background: There is no specific DTC evident for the scenario described. The issue described is evident as the rear seat belt buckles are not resistor coded The system uses a non-resistor coded buckle strategy (zero-infinity or open-closed buckle) for the rear seats. In correct operation, a fastened seatbelt is open circuit and an un-fastened seatbelt is closed circuit If harness damage is present or an electrical connector joint is not properly engaged, an unintended open circuit occurs. This will give an incorrect buckle status reading within the DIP The advice within this TPI should be referred to first before conducting any further diagnosis or disassembly of the vehicles interior Previous assembly/disassembly may have caused an unintentional open circuit when operatives have been working on or around the rear seat belt assemblies

Technical background: If an issue is suspected for one of the control modules listed below: - Onboard supply control unit (J519) - Convenience system central control unit (J393) - Data bus diagnostics interface (J533) - Control unit 1 for Information Electronics (J794) - Control unit in dash panel insert (J285) - Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query. The donor of parts should only be used as a temporary test VERY IMPORTANT: The ODIS replace routine MUST NOT be carried out under any circumstances.

fuel pump control units please refer to the information within this TPI

deactivation of the steering wheel heating function

mismatched terminal locations of the Pressure sensor for the activated charcoal filter system -G804

range/performance DTCs evident within numerous control units

Customer Statement: -The following DTCs could also be evident within the diagnostic address 0046 and/or 00BB and/or 00BC -B131DF5: alarm system siren supply voltage lower limit value less than -B131D29: sirens/alarm horn for anti-theft warning system range/performance -B131D29: anti-theft alarm system siren/alarm horn signal, not valid

parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the measure of this section of this TPI.

Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.

or B191604 evident within address 0019 - Gateway (Data bus diagnostic interface control unit) - J533 Technical Background: -In the event any of the afore mentioned DTCs are evident within address 0019 - Gateway (Data bus diagnostic interface control unit) - J533 - Refer to the Measure section of this TPI

Customer statement / workshop findings: Message on Bentley Rear Entertainment Tablet - The battery is defective Please contact your Bentley dealer. Technical background: The Bentley Rear Entertainment Tablet incorporates battery voltage protection, under certain conditions this system can prevent the internal battery from accepting a charge current, this would normally require the Tablet to be replaced. This TPI provides the necessary information to replace the Tablet internal battery pack.

Customer statement / workshop findings: - PDC system not working or PDC system false detection - Warning evident within the DIP Workshop findings: - Parking aid sensor Range/Performance DTCs evident within numerous control units Technical background: Refer to the Measure section of this TPI

Customer statement / workshop findings: Unintended sounding of the alarm siren following activation of the ignition Or Unintended sounding of the alarm siren whilst the vehicle is left standing Workshop findings. The following DTCs could also be evident within diagnostic address 0046 and/or 00BB and/or 00BC - B131DF5: alarm system siren supply voltage lower limit value less than - B131D29: sirens / alarm horn for anti-theft warning system Range/Performance - B131D29: anti-theft alarm system siren / alarm horn signal, not valid Technical background: In the event the symptom(s) described are evident, please refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: High voltage system warning within the DIP Workshop findings: Power Electronics DTC P060600 evident within address 51 - Electric drive Control unit (DTC cannot be cleared) Technical background: DTC P060600 relates to an Active discharge counter error within address 51 (DTC cannot be cleared) In the event the symptoms are as described, conduct the instructions within the Measure section to completion noting the following: IMPORTANT: There are separate SVM codes and MUST be strictly applied as instructed - 4V051SW01 (MUST BE APPLIED FIRST) - 4V0EDU01 (MUST BE APPLIED SECOND)

Workshop findings: Defective upper inner lever bush. Technical background Verify that the customer complaint matches the sound file within the Bentley Hub Reference TPI Transaction number 2064779/-. The noise present in the sound file is caused by defective upper inner lever bush/bushes, the noise can appear in the following possible scenario. -When the vehicle is moved with steering input over uneven surfaces (for e.g. a ramp or speed bump). If the customer complaint occurs in any of the above circumstances and the noise can be clearly assigned to the noise within the sound file Refer to the instructions within the Measure section of this TPI. VERY IMPORTANT NOTE FOR HYBRID VEHICLES: -Hybrid vehicles use a High voltage system and MUST only be worked on by suitably qualified personnel. -Please ensure all guidelines within the repair manual are strictly followed before and whilst conducting any work on vehicles with a High voltage system

-No error messages are shown within the DIP Workshop findings: DTC U101100 evident within address 09 - DIP Unrecoverable due to low voltage

Workshop findings: DTC P060600 with symptom code 29313 is evident within address 51 - Electric drive Control unit (DTC cannot be cleared). Technical background: DTC P060600 with symptom code 29313 relates to an Active discharge counter error within address 51 (DTC cannot be cleared) In the event the symptoms are as described, conduct the instructions within the Measure section to completion noting the following: IMPORTANT: There are separate SVM codes and MUST be strictly applied as instructed: -4V051SW01 (MUST BE APPLIED FIRST) -4V0EDU01 (MUST BE APPLIED SECOND)

Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

light control unit (Diagnostic address D6) and/or the right light control unit (Diagnostic address D7) There are numerous static and intermittent DTCs which maybe evident within the previously mentioned control units, ensure all steps within the Measure section are strictly adhered to New Flying Spur (20 - 22 M/Y) and Bentayga (21 - 22 M/Y). In the event that DTCs C119813 Low beam light bulb open circuit or C1198FA Low beam light bulb short circuit are evident in D6 and/or D7. Please refer to and conduct the instructions within the following TPIs New Flying spur - TPI 2063777/- Bentayga applicable to 21 and 22 M/Y only - 2064497/-. For any other issues please refer to the instructions within the Measure section of this TPI.

one of the control modules listed below: - Onboard supply control unit (J519) - Convenience system central control unit (J393) - Data bus diagnostics interface (J533) - Control unit 1 for Information Electronics (J794) - Control unit in dash panel insert (J285) - Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query.

Workshop findings: DTC - B2000F2: Faulty control module (Symptom code 4102) evident within address 0084 Night vision control module. Technical background: IMPORTANT: In the event that the issue is evident and the vehicle is post the VINs shown below, a DISS query must be raised ensuring the following is attached to the query. -Detailed description in which the issue occurred, for example -Driving on a quiet road with no traffic, conditions were wet, the road had no street lighting. -Clear photographs showing the condition of the night vision camera and night vision camera lens. -Current and up to date ODIS log. However, should the vehicle be prior to the VIN cut off, the operative MUST carry out the instructions within the Measure section of this TPI. New Flying Spur New Continental GT and New Continental GTC (all vehicles from SCBCD13S1KC071068 are to specification). Bentayga (all vehicles from SJAAL14V0KC025622 are to specification).

Customer statement / workshop findings: 12 Volt Battery test instruction Technical background: For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: Air suspension system warning displayed in the Driver Instrument Panel (DIP) Technical background: Diagnostic Trouble Code (DTC) C103129 Level control pressure sensor Implausible signal symptom (DTC) stored in the Chassis control unit (Address 74). The onward procedure will check, and if necessary, perform software updates to Addresses 74, D4 and D5. This will bring them to the latest, compatible software level.

Customer statement / workshop findings: Refer to the Technical background section before considering the fitment of control modules from donor vehicles for test purposes Technical background: If an issue is suspected for one of the control modules listed below: - Onboard supply control unit (J519) - Convenience system central control unit (J393) - Data bus diagnostics interface (J533) - Control unit 1 for Information Electronics (J794) - Control unit in dash panel insert (J285) - Emergency call module control unit (J949) The fitment of donor parts from another vehicle is not advisable and only possible if approved from Product Support via an open DISS query. The donor of parts should only be used as a temporary test VERY IMPORTANT: The ODIS replace routine MUST NOT be carried out under any circumstances

Technical background For all 12 volt battery issues relating to warranty or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI.

Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI

Customer statement / workshop findings: Message on Bentley Rear Entertainment Tablet: The battery is defective Please contact your Bentley dealer. Technical background: The Bentley Rear Entertainment Tablet incorporates battery voltage protection, under certain conditions this system can prevent the internal battery from accepting a charge current, this would normally require the Tablet to be replaced. This TPI provides the necessary information to replace the Tablet internal battery pack.

on Bentley Rear Entertainment Tablet The battery is defective Please contact your Bentley dealer . Bentley Rear Entertainment Tablet will not accept a charge current. Technical background The Bentley Rear Entertainment Tablet incorporates battery voltage protection, under certain conditions this system can prevent the internal battery from accepting a charge current, this would normally require the Tablet to be replaced. This TPI provides the necessary information to replace the Tablet internal battery pack.

Customer statement/workshop findings DTCs B19186F0 or B1916F3 or B191604 evident within address 0019 - Gateway (Data bus diagnostic interface control unit) - J533 Technical background: In the event any of the afore mentioned DTCs are evident within address 0019 - Gateway (Data bus diagnostic interface control unit) - J533 - Refer to the Measure section of this TPI

Customer statement / workshop findings After replacing the software or hardware for the Adaptive suspension control unit (J775 Diagnostic address 74) or the Front Roll stabilisation control unit (J924 Diagnostic address D4) and/or the Rear Roll stabilisation unit (J1096 Diagnostic address D5) the software could be incompatible between the control units Technical background The Adaptive air suspension control unit (J775) functions as a universal control unit for the chassis control systems. The Adaptive air suspension control unit (J775) controls several functions in the car in particular the master for the active roll control system, The control unit contains developed suspension and damping control software. Should one of the modules be replaced for example (J775) on an early model vehicle the newer software contained within the replacement control unit may not be compatible with (J924) and/or (J1096)

Customer statement / workshop findings: Correct functionality and restrictions of the Mulliner Biometric Secure Stowage Box need to be understood to prevent unnecessary customer complaints.

Customer statement / workshop findings: Button Module For Driving Profile Selection requires replacement. Technical background: There is an ongoing factory investigation into failures of the Button Module For Driving Profile Selection. Any Button Module For Driving Profile Selection that is removed due to a fault is to be returned fully assembled using the Warranty parts return process.

Technical background: On all affected Bentayga vehicles, incorrect software in the HVAC control module can lead to functionality issues. Remedy: On all affected vehicles the software of the HVAC control module must be updated.

B19186F0 or B1916F3 or B191604 evident within address 0019 - Gateway (Data bus diagnostic interface control unit) - J533 Technical background: In the event any of the afore mentioned DTCs are evident within address 0019 - Gateway (Data bus diagnostic interface control unit) - J533 - Refer to the Measure section of this TPI Measure: Referring to Figure 1 - Replace the back up battery for emergency supply (Point A)

Driving Profile Selection requires replacement. Technical background: There is an ongoing factory investigation into failures of the Button Module For Driving Profile Selection. Any Button Module For Driving Profile Selection that is removed due to a fault is to be returned fully assembled using the Warranty parts return process. Measure When removing the Button Module For Driving Profile Selection due to a fault condition, do not attempt to disassemble and rectify, once removed assemblies should be returned using the Warranty parts return process.

findings: Early deactivation of the steering wheel heating function Technical background: DTC B145504 - Temperature sensor steering wheel heater Faulty - 'passive sporadic' logged within address 16 (J527 Steering column electronics) in conjunction with the warning message shown within the DIP (Figure 1) Measure: This TPI is only applicable to vehicles built up to and including the production date of 08/10/2018 1) In the event the issue is exactly as described within the Technical background section of this TPI Replace the steering column switch Refer to Rep.Gr 96 - Steering column combination switch (J527) using part number 36A 907 129S

defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI

or a parts warranty claim, a DISS query MUST be raised prior to battery replacement, refer to the instructions within the Measure section of this TPI

bus diagnostic interface control unit) - J533 Technical background: In the event any of the afore mentioned DTCs are evident within address 0019 - Gateway (Data bus diagnostic interface control unit) - J533 - Refer to the Measure section of this TPI Measure: Replace the Gateway (Data bus diagnostic interface control unit) - J533 - Back up battery for emergency supply NOTE: The battery is fitted within the control unit

affected vehicles a Software Version Management action is required.

Customer statement: PDC system not working or PDC system false detection Warning evident within the DIP

format for analysis by Product Support Technical Background: The instructions within the Measure section of this TPI have been generated to guide operatives through the process for recording Measured values in cycles by using self diagnosis, the Instructions also detail how to locate corresponding files which are required for analysis

Customer statement / workshop findings: During fault finding, the following may be observed: DTC B200FFE (Internal Malfunction) stored in the following diagnostic address: Front Sway Stablization Control Unit (00D4)Or Rear Sway Stablization Control Unit (00D5)

Customer statement: PDC system not working or PDC system false detection Warning evident within the DIP

Condition: The front camera for driver assistance programs (mono camera) requires replacement.

Condition: Leakage found on the foremost lower trailing arm bush

Condition: Customer may report that the seat ventilation system is not functioning with no airflow from the seat ventilation ducts.

Condition: In some cases Measured value traces may be requested in XML format for analysis by Product Support.

Condition: Customers may report that they are unable to register their 18MY or 19MY Bentley vehicle in the My Bentley App.

Condition: Customer may report that the seat ventilation system is not functioning with no airflow from the seat ventilation ducts.

Customer statement: Water ingress within the rear lid Water dripping from the rear lid Water ingress is evident within the boot Water in some isolated cases may be heard moving/sloshing from the inside of the rear lid

Customer statement: The rear seat massage function is not working correctly Or The massage function appears to be unresponsive/weak regardless of the setting/function selected

Condition: In some cases, Measured value traces may be requested in XML format for analysis by Product Support

Customer statement: Water ingress within the rear lid Water dripping from the rear lid Water ingress is evident within the boot Water in some isolated cases may be heard moving/sloshing from the inside of the rear lid

Technical background The instructions within the Measure section of this TPI have been generated to guide operatives through the process for recording Measured values in cycles by using self diagnosis, the Instructions also detail how to locate corresponding files which are required for analysis.

Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

Technical Background: -Deviations in the key blade and key fob assembly could make it difficult to remove the key blade.

Communication Unit

feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported.

-Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle.

camera washer jet

blade and key fob assembly could make it difficult to remove the key blade.

Customer statement / workshop findings: Clicking noises from the left and/or right front corner(s) Technical background: In order to accurately diagnose and repair customer reported clicking noises from the front corner(s) the Measure section of this TPI consists of three individual sections, each section describes the symptom and the remedy which should be applied. Symptoms and descriptions regarding clicking noises can appear to be very similar when described, where possible the customer should demonstrate the reported symptom to enable correct diagnosis.

Customer statement / workshop findings The front wing Flying B is loose/rattling Or The front wing Flying B is detached from the front wing. Measure In the event the front wing Flying B brightware is loose/rattling carry out the onward instructions from step 1 However In the event the front wing Flying B brightware is detached (not damaged) carry out the instructions from step 2 HINT: The front wing does not require removal to conduct this procedure 1) Referring to Rep.Gr 66 - Remove the front wing 'Flying B' 2) Using a suitable cleaning agent for example 3M surface cleaner and suitable cloth, thoroughly clean the brightware aperture and the front wing 'Flying B' 3) Using the adhesive as per the Parts information section - Apply the adhesive in the three locations shown in Figure 3

Customer statement / workshop findings: Clicking noises from the left and/or right front corner(s) Technical background: In order to accurately diagnose and repair customer reported clicking noises from the front corner(s) the Measure section of this TPI consists of three individual sections, each section describes the symptom and the remedy which should be applied Symptoms and descriptions regarding clicking noises can appear to be very similar when described, where possible the customer should demonstrate the reported symptom to enable correct diagnosis.

Customer statement / workshop findings: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted.

Customer statement / workshop findings: Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted

Customer statement / workshop findings: Deployable sill step accessory malfunctions. Technical background: This TPI is specifically written to record key information, reach a logical diagnosis and ultimately a problem resolution when presented with a deployable sill step malfunction. Please report via DISS all findings during your investigation and rectification process.

Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

Customer statement / workshop findings Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted

Customer statement/workshop findings Clicking noise from front corner(s) Technical background In order to accurately diagnose and repair customer reported clicking noises from the front corner(s) the Measure section of this TPI consists of three individual sections, each section describes the symptom and the remedy which should be applied Symptoms and descriptions regarding clicking noises can appear to be very similar when described, where possible the customer should demonstrate the reported symptom to enable correct diagnosis

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. All Vehicle Variants - Spurious DTC List Technical background The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted

Technical background: In order to accurately diagnose and repair customer reported clicking noises from the front corner(s) the Measure section of this TPI consists of three individual sections, each section describes the symptom and the remedy which should be applied Symptoms and descriptions regarding clicking noises can appear to be very similar when described, where possible the customer should demonstrate the reported symptom to enable correct diagnosis.

Customer statement/workshop findings: PDC system not working or PDC system false detection Technical background Refer to the Measure section of this TPI

Technical background: In order to accurately diagnose and repair customer reported clicking noises from the front corner(s) the Measure section of this TPI consists of three individual sections, each section describes the symptom and the remedy which should be applied Symptoms and descriptions regarding clicking noises can appear to be very similar when described, where possible the customer should demonstrate the reported symptom to enable correct diagnosis

clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work Technical Background It is the retailers responsibility to check and confirm if there are any TPIs which are applicable to the customers complaint/issue if there is an applicable TPI available, apply it and complete a DISS complaint to include Workshop findings only (No repair query required). For correct diagnosis and repair the attached Flowchart must be followed in conjunction with the Measure section of this TPI

accurately diagnose and repair customer reported clicking noises from the front corner(s) the Measure section of this TPI consists of three individual sections, each section describes the symptom and the remedy which should be applied Symptoms and descriptions regarding clicking noises can appear to be very similar when described, where possible the customer should demonstrate the reported symptom to enable correct diagnosis

sufficiently Technical background: Should the auxiliary and cabin heating system not be working to specification the checks within the Measure section should be considered Try to reproduce the customer complaint so that it can be clearly assigned to this TPI

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Measure: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken.

This TPI is specifically written to record key information, reach a logical diagnosis and ultimately a problem resolution when presented with a deployable sill step malfunction.

and/or retailer may identify visual damage/anomalies in the paint finish during or post pre-delivery inspection. These may include: Uneven sheen or texture Patchy or blotchy appearance Inconsistent under lighting Staining, discolouration, or surface blemishes

Customer may report that the sunroof blind is stuck in the closed position and cannot be opened using interior controls. The Sunroof blind is stuck due to uneven/ruffled or crumped during open or closing

Customer statement / workshop findings: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness.

Customer Statement: The customer reports that the vehicle door locking and/or unlocking does not function correctly. This may include intermittent operation, non-response to remote or interior commands, or inconsistent locking behaviour.

and/or retailer may identify visual damage/anomalies in the paint finish during or post pre-delivery inspection. These may include: Uneven sheen or texture Patchy or blotchy appearance Inconsistent under lighting Staining, discolouration, or surface blemishes

vehicle door locking and/or unlocking does not function correctly. This may include intermittent operation, non-response to remote or interior commands, or inconsistent locking behaviour.

Customer statement / workshop findings: Driver and / or Passenger door creak during the Power close function - Front and / or rear (Depending on vehicle type)

Condition: Customers and retailers may raise enquiries regarding the cleaning and appearance of Dinamica interior trim materials. Workshop inspection confirms no material defects, with concerns related solely to approved cleaning and maintenance guidance

Condition: Customer may report that the sunroof blind is stuck in the closed position and cannot be opened using interior controls. The Sunroof blind is stuck due to uneven/ruffled or crumped during open or closing.

Condition: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness.

Condition: In rare instances the customer and/or retailer may identify visual damage/anomalies in the paint finish during or post pre-delivery inspection. These may include: Uneven sheen or texture Patchy or blotchy appearance Inconsistent under lighting Staining, discolouration, or surface blemishes

Condition: Customer may report that the sunroof blind is stuck in the open position and cannot be closed using interior controls. The Sunroof blind is stuck due to uneven/ruffled or crumped during open or closing.

Condition: In rare instances the customer and/or retailer may identify the presence of damage or visual anomalies on leather trimmed surfaces within the vehicle cabin during or post pre-delivery inspection.

Condition: Rear door blind is inoperative.

Condition: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness.

Condition: Customer and/or retailer may raise an issue with panel gaps/alignment or flushness

Condition: In the event a complaint is received regarding road wheel/s condition for example: Scratches Corrosion Damage Blemishes Chipping

condition for example: - Scratches - Corrosion - Damage - Blemishes - Chipping Please refer to the onward instructions

The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips.

should be followed to assist in the diagnosis of water leaks or wind noise.

condition for example: -scratches -corrosion -damage -blemishes -chipping

lamps are steamed up/damp from the inside with minor drips

- Standard (STD) not Privacy (PRV) or visa versa and/or Defects are evident within the glass Technical Background: -The instructions within the Measure section MUST only be followed if the glass is to be replaced

Customer statement / workshop findings: In the event that a trim mismatch is detected for example: - Piano black veneer is supplied although the customer ordered walnut veneer Or - The interior trim colour is incorrect for example: Cricket ball interior trim is supplied although the customer ordered Hotspur The operative should refer to the Technical background section

Customer statement / workshop findings: Rear window blind/s do not fully retract (Jammed)

Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

Customer statement / workshop findings Customer statement: 1. The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. or 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips. Technical background 1. Damp air settles on the inner lens of the headlights/fog lamps, with recognisable misting in certain weather conditions (comparable with the steaming up of spectacle lenses when entering a warm room in winter or of the bathroom mirror after a shower). 2. Leak on the headlights/front fog lamps. For example through open covers, a damaged seal of the cap or similar.

Refer to the vehicle repair history to check and confirm any previous work done regarding door latch replacement noting the following: - Only replace the door latch which is exhibiting the symptom

Customer statement / workshop findings Driver or Passenger door creak during the Close function Technical background: Refer to the vehicle repair history to check and confirm any previous work done regarding door latch replacement noting the following: - Only replace the door latch which is exhibiting the symptom

Scratches - Corrosion - Damage - Blemishes - Chipping Please refer to the onward instructions. Technical background: Do not consider submitting a warranty claim for a road wheel manufacturing defect without first referencing and understanding the contents of this document. Any defect or concern found either outside the guidelines stated in this document or not clearly stated as acceptable to support a warranty claim, will be the responsibility of the retailer regarding component replacement. Any road wheels deemed as having no issues found relating to a manufacturing defect (including curbing) will have the applicable claim rejected

Customer statement / workshop findings: Water leak/wind noise evident Technical background: The instructions within the Measure section should be followed to assist in the diagnosis of water leaks or wind noise

Customer statement / workshop findings: The alignment pin used to locate the front door trim panel is broken (Figure 1). Measure: The front alignment pin is required to aid alignment of the door trim panel to the door panel during the Manufacturing process NOTE: In Service the alignment pin is not required NOTE: Replacement parts are not needed and are not available to order Referring to Figure 1 Remove and discard the following: - Broken alignment pin x1 ( If evident) - Fixings x3 - Alignment pin plate x1 TIP: Cover the area in which the plate was previously fixed using anti creak tape If the condition is as shown in Figure 2 - The removal of the alignment pin/plate and fixings is not required unless broken.

Customer statement / workshop findings: Noises from the Panoramic sun roof when driving. The noises occur mainly when the sun roof is closed. Technical background: Mechanical system of sun roof frame not or insufficiently lubricated.

Customer statement / workshop findings: Bentley Dynamic ride system fault (Figure 1) within the Drivers Information Panel (DIP) with DTC C129600 logged within the Front anti roll bar control unit (Diagnostic address D4) and/or the Rear anti roll bar control unit (Diagnostic Address D5) Technical background: Should the symptoms be evident as described, refer to the Measure section of this TPI, ensure both of the suggested earth points are checked regardless if the DTC is logged in the front or rear anti roll bar control unit

Customer statement / workshop findings: Noise complaint from the interior Workshop findings: The noise can be reproduced and clearly assigned to the interior Prior to starting the instructions within this TPI, the Retailer must check and confirm the vehicle is in standard factory condition and has not had any non-approved aftermarket modifications conducted Should any aftermarket modifications be found, the Retailer must make Product Support aware by raising a DISS query to report the details of the modification, you must then await feedback from Product Support before conducting any further work

The lenses of the headlights (illustration 1a) /front fog lamps (illustration 1b) are steamed up/damp from the inside with minor drips. 2. Water is in the headlight (illustration 2a) / front fog lamp (illustration 2b), big drips. Technical Background 1. Damp air settles on the inner lens of the headlights/fog lamps, with recognisable misting in certain weather conditions (comparable with the steaming up of spectacle lenses when entering a warm room in winter or of the bathroom mirror after a shower). 2. Leak on the headlights/front fog lamps. For example through open covers, a damaged seal of the cap or similar.

instructions within the Measure section for removal instructions

The front door/s power latching system sporadically does not work. The door remains in the first latch of the door lock and is not closed by the power latching system. The micro switch signal of the door lock is not recognised or too briefly. A counter-pressure of the door is required to clearly recognise the signal. Check whether there are other TPIs for the complaint, for example the software of the door control units are up to date

Customer statement / workshop findings: During diagnosis using ODIS, Measured Value Blocks (MVBs) for: Visible satellites, tracked satellites (within J949 Emergency Call Control Module Conbox) may display blank or no value. This condition may be interpreted as a GPS reception fault, antenna issue or connectivity malfunction. Diagnostic logs may also show absence of satellite values.

Customer statement / workshop findings: One or a combination of the following is evident within the DIP (Figure 1) Electronic parking brake warning And/or Drivers door power latch intermittent operation warning

Condition: One or a combination of the following is evident within the DIP Electronic parking brake warning And/or Drivers door power latch intermittent operation warning

Technical Background: When opting to use Winter Tyres on vehicles specified with Ceramic brake rotors, the only permissible wheel rim option is 21 Inch 7 Twin spoke 36A 601 025Q.

Technical Background: Brake noises can be attributed to many causes, the most common causes are as follows: Brake discs or pads are close to their wear limit New brake pads and/or discs have not been properly bedded in after installation Aftermarket pads or discs are installed There is debris such as small stones, grit, road salt or sand between the brake disc and pad Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time

Customer statement / workshop findings: One or a combination of the following is evident within the DIP Electronic parking brake warning And/or Drivers door power latch intermittent operation warning

Scenario 1 Vibration of 1.2 to 1.4 KHz is produced from the rear brakes whilst braking at low speed Whilst braking at low speed, a vibration of 1.2 to 1.4 KHz or 5 KHz can be produced from friction between the rear brake pad and disc resulting in rear brake noise/squeal Scenario 2 Vibration of 3.4 KHz is produced from the rear brakes While braking at low speed a vibration of 3.4 KHz can be produced during brake application at low speed resulting in rear brake noise/squeal Scenario 3 Vibration of 5 KHz is produced from the rear brakes whilst braking at low speed Whilst braking at low speed, a vibration of 5 KHz can be produced from friction between the rear brake pad and disc resulting in rear brake noise/squeal.

-The noise/squeal can be reproduced and clearly assigned to the braking system

Technical background: When opting to use Winter Tyres on vehicles specified with Ceramic brake rotors, the only permissible wheel rim option is 21 Inch 7 Twin spoke 36A 601 025Q.

vehicles specified with ceramic brake rotors, the only permissible wheel rim option is 21 inch 7 twin spoke - 36A601025Q

46 Customer Statement: -Electronic parking brake warning evident within the DIP

is caused by defective lower suspension lever - rear - hydraulic mounts. In order to reproduce the noise this bush must be twisted, therefore the noise can appear in the following circumstances. -When performing parking maneuvers with the brake applied -When steering from lock to lock with the vehicle in motion and the brake applied -When the vehicle is moved with steering input over uneven surfaces (a ramp or speed bump)

Technical Background: -While braking at low speed, a vibration of 1.2 to 1.4 KHz can be produced by the friction between the rear brake pad and disc resulting in a complain of brake noise from the customer.

Customer statement / workshop findings Front brake squeal with a frequency of 1.5 KHz to 2.0 KHz Technical background: Modified front brake Callipers and modified front brake disc guard plates are available on receipt of a qualifying DISS query. Referring to Figure 1, the replacement front callipers have a Dynamic absorber fitted (A), the brake disc guard plates (B) are pre modified to fit around the absorber.

Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Service: Note: For correct diagnosis and repair the attached Flowchart must be followed. 1. Check the overall condition of the brakes to determine if the brake noise can be attributed to one of the causes listed in the Technical Background section of this TPI. If the noise is not a result of one these causes, proceed with point 2. 2. Record the noise and frequency For the frequency analysis and the noise recording we recommend using the Chassis Ear Tool WT 10437. To record the noise and measure the frequency using WT 10437 Chassis Ear Tool follow these instructions; Refer to File recording in the WT 10437 user instructions.

Customer statement / workshop findings: Front brake squeal with a frequency of 1.8 KHz to 1.9 KHz Technical background: Modified front brake Calipers and modified front brake disc guard plates are available on receipt of a qualifying DISS query Referring to Figure 1, the replacement front calipers have a Dynamic absorber fitted (A), the brake disc guard plates (B) are pre modified to fit around the absorber.

Customer statement / workshop findings: - Undesirable odour emanating from the front wheel arches, the issue occurs after the vehicle has reached normal operating temperature - The odour can also be evident within the cabin Technical background: HINT: The issue described is mainly evident on low mileage/low use vehicles with iron brakes In the event the symptoms are as described, please conduct the instructions within the Measure section of this TPI

Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).

Customer statement / workshop findings: Noise/Creak from the rear seat/s at speeds up to 70 mph And/or Creaking from rear seat/s between 0-20 mph during gentle acceleration and braking Technical background: This TPI applies to all 5 and 7 seat variants This TPI does not apply to 4 seat variants Noises and creaks originating from the rear seat/s as a result of seat location pegs and mega bracket interference while driving at speeds up to 70 mph and gentle acceleration and braking between 0-20 mph should be resolved by following the instructions within the Measure section.

1.8 KHz to 1.9 KHz Technical background: Modified front brake Calipers and modified front brake disc guard plates are available on receipt of a qualifying DISS query Referring to Figure 1, the replacement front callipers have a Dynamic absorber fitted (A), the brake disc guard plates (B) are pre modified to fit around the absorber

Technical background: While braking at low speed, a vibration of 1.2 to 1.4 KHz can be produced by the friction between the rear brake pad and disc resulting in a complaint of brake noise from the customer

vehicles specified with Ceramic brake rotors, the only permissible wheel rim option is 21 Inch 7 Twin spoke 36A 601 025Q. Measure: If requested to fit Winter Tyres on vehicles specified with Ceramic brake rotors, please advise the Customer that the only permissible wheel rim is 21 Inch 7 Twin spoke 36A 601 025Q. Parts

Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).

Technical background: In certain circumstances a ticking noise behind the Driver Instrument Panel may be audible within the vehicle cabin. The ticking noise emanates from the vacuum system and may be more noticeable following several successive brake pedal actuations. Refer to the video on the Bentley Hub referencing TPI 2054077/3 If the complaint noise is as shown in the video, the customer should be advised that this is normal and does not represent a failure or malfunction on the vehicle

Customer statement/workshop findings: Ticking noise behind Driver Instrument Panel. Technical background: In certain circumstances a ticking noise behind the Driver Instrument Panel may be audible within the vehicle cabin. The ticking noise emanates from the vacuum system and may be more noticeable following several successive brake pedal actuations.

Customer statement / workshop findings: Creaking noise from the front suspension when manoeuvring Technical background: Verify that the customer complaint matches the sound file within the Bentley Hub Reference TPI Transaction number 2048616 TIP: When listening to the sound file the noise can be heard from between 0 and 3 seconds The noise present in the sound file is caused by defective Lower suspension lever - Rear - Hydraulic mounts. In order to reproduce the noise this bush must be twisted, therefore the noise can appear in the following circumstances When performing parking manoeuvers with the brake applied When steering from lock to lock with the vehicle in motion and the brake applied When the vehicle is moved with steering input over uneven surfaces (for e.g. a ramp or speed bump) If the customer complaint occurs in any of the above circumstances and the noise can be clearly assigned to the noise within the sound file Refer to the instructions within the Measure section of this TPI

Customer statement / workshop findings: Squeal from the rear of the vehicle at low speed while braking. Technical background: While braking at low speed, a vibration of 1.2 to 1.4 KHz can be produced by the friction between the rear brake pad and disc resulting in a complaint of brake noise from the customer

the front suspension when manoeuvring Technical background: Verify that the customer complaint matches the sound file within the Bentley Hub Reference TPI Transaction number 2048616 TIP: When listening to the sound file the noise can be heard from between 0 and 3 seconds The noise present in the sound file is caused by defective Lower suspension lever - Rear - Hydraulic mounts. In order to reproduce the noise this bush must be twisted, therefore the noise can appear in the following circumstances: When performing parking manoeuvers with the brake applied When steering from lock to lock with the vehicle in motion and the brake applied When the vehicle is moved with steering input over uneven surfaces (for e.g. a ramp or speed bump) If the customer complaint occurs in any of the above circumstances and the noise can be clearly assigned to the noise within the sound file Refer to the instructions within the Measure section of this TPI

Technical Background: While braking at low speed, a vibration of 1.2 to 1.4 KHz can be produced by the friction between the rear brake pad and disc resulting in a complaint of brake noise from the customer

Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1). 6. Discs have a groove in them (Figure 2) 7. There is chemical contamination on the braking surface of the disc due to a wheel or tyre cleaner being sprayed directly onto the disc (Figure 3). 8. There are pad marks on the brake disc as a result of the brake pad material transferring to the discs. This can occur when a vehicle has been stood for long periods of time in a wet or snowy environment (Figure 4).

Condition: The right and/or left hand front rearmost lower suspension lever inner hydraulic mounts are leaking oil or showing signs of dry oil stains

Customer statement / workshop findings: Customers will not be aware of any DTCs, workshop operatives may discover spurious DTCs whilst running Guided Fault Finding (GFF) when using ODIS Technical background: To determine the course of action which should be taken the operative should refer to the Bentley Hub referencing the following: Spurious DTC list for TPI 2072055 The document contains all known spurious DTCs for all applicable vehicle variants.

Customer statement / workshop findings: Customers will not be aware of any fault codes Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).

Customer statement / workshop findings: The right and/or left hand front rearmost lower suspension lever inner hydraulic mounts are leaking oil or showing signs of dry oil stains. Technical background: In the event the symptom is as described please refer to the Measure section of this TPI to confirm if the right and/or left hand front rearmost lower suspension lever inner hydraulic mounts require replacement or not

Basic setting (full process + rebound end stops) after a new adaptive air suspension control unit has been fitted or work has been conducted on the suspension system which requires the Basic setting (full process + rebound end stops) procedure performing

visible at the boot of the lower ball joint (grease emerging) however the boot does not show any damage

Customer Statement: -Air suspension warning light within the DIP

Customer statement / workshop findings: -Customers will not be aware of any fault codes -Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: -The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants -Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).

Customer statement / workshop findings - Vehicle sitting low on one or more corners when static - No relevant DTCs are evident Technical background: Refer to the Measure section of this TPI. Measure: 1) Confirm there are no DTCs indicating a fault with the air suspension system or associated systems 2) Refer to the instructions within TPI 2053492/- to confirm that no air leaks or issues relating to the air springs are evident.

Customer statement / workshop findings Customer will not be aware of any fault codes. Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical background The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the document (loaded onto the Hub) regarding the DTC description and actions (if any) which should be conducted

Customer statement / workshop findings: Driver or Passenger door creak during the power latch Close function Technical background: Refer to the Measure section of this TPI Measure: Ensure the fault is as described within the Customer statement, refer to the video on the Bentley Hub referencing TPI 2052394/-

Customer statement/workshop findings: Unable to run Basic setting (full process + rebound end stops) after a new adaptive air suspension control unit has been fitted or work has been conducted on the suspension system which requires the Basic setting (full process + rebound end stops) procedure performing Technical background: Referring to Figure 1, During the Basic setting (full process + rebound end stops) the routine can stop during the initial part of the procedure, in particular at the stage shown in Figure 2, which is when the vehicle is raised to allow all four wheels to hang down to their full rebound position Should this issue be evident and the Basic settings routine does not continue - Refer to the Measure section of this TPI

In the event DTC C1260F0 - Compressor electronics for suspension levelling is evident within address 74 carry out the software update within the Measure section of this TPI. The update will automatically update the following control units (Depending on actual/current software level) Adaptive suspension control unit (J775 Diagnostic address 74) Rear Roll stabilisation unit (J1096 Diagnostic address D5) Front Roll stabilisation control unit (J924 Diagnostic address D4)

Customer statement / workshop findings: The customer requests improved and/or newer navigation functionality, including access to the latest navigation maps and updated map content.

Customer statement / workshop findings: Windscreen cracked/damaged

Condition: Issue suspected with the Infotainment Main unit (5F / J794) - For example: MMI screen image flickers or goes blank No response to selection Audio cuts out

Customer statement / workshop findings: Water ingress into the cabin (Front windscreen)

Customer statement / workshop findings: Issue suspected with the Infotainment Main unit (5F / J794) - For example: - MMI screen image flickers or goes blank - No response to selection - Audio cuts out.

services personalisation feature does no longer function. The in car services personalisation function can be found by navigating through the screen menu.

changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit.

initially be locked with a component protection warning displayed.

Customer statement / workshop findings Issue suspected with the Infotainment Main unit (5F / J794) - For example: - MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background The operative should continue as follows: - Complete the questionnaire within the Measure section of this TPI (Part 1) once completed the questionnaire should be attached to an existing or already open DISS query - Once the questionnaire is complete, the operative should refer to (Part 2) within the Measure section regarding fault finding/diagnosis of the Infotainment Main unit (5F / J794)

suspected with the Infotainment Main unit (5F / J794) - For example: -MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background: Refer to the Measure section regarding any Infotainment Main unit (5F / J794) fault finding/diagnosis

cracked/damaged Technical background: Please refer to the instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged NOTE: The instructions MUST be followed to help the retailer clarify if the windscreen should be replaced under manufacturers warranty (Stress crack) or Customer pay/insurance (external influence damage)

Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference

Customer statement / workshop findings: Issue suspected with the Infotainment Main unit (5F / J794) - For example: - MMI screen image flickers or goes blank - No response to selection - Audio cuts-out Technical background: Refer to the Measure section regarding any Infotainment Main unit (5F / J794) fault finding/diagnosis

Customer statement / workshop findings Unable to stream media to the rear seat entertainment system from the Infotainment system Technical background The ability to steam CD/DVD and TV to the rear seat entertainment system from the Infotainment system is no longer available from 19 Model Year onwards.

Customer statement / workshop findings: Unable to stream media to the rear seat entertainment system from the Infotainment system Technical background: The ability to steam CD/DVD and TV to the rear seat entertainment system from the Infotainment system is no longer available from 19 Model Year onwards.

Customer statement / workshop findings: All complaints which are related to radio reception issues Technical background: Complaints about the radio reception can have many causes. The radio reception strength/quality at the vehicle location can be an important issue. To process such complaints as effectively as possible it is important to precisely record the circumstances when a complaint occurs. The attached check list is available for this purpose. Please ensure the instructions within the Measure section are strictly adhered to

Customer statement/workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit.

Customer statement / workshop findings: Customer states: Unable to program their garage door opener to the vehicle. Message displayed in MMI: An error occurred during programming. Would you like to try again? Workshop findings: Customer supplied remote control will not program to customer vehicle, but may program to other vehicles. Other garage door opener remotes may pair to the customer vehicle. This TPI is only valid for cars with "lane change assist" fitted Technical background: Under certain circumstances the radio signal of the customers remote control may not be adapted to the vehicle.

Customer statement / workshop findings: Windscreen cracked/damaged Technical background: Please refer to the instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged

Message displayed in MMI: An error occurred during programming. Would you like to try again? Workshop findings: Customer supplied remote control will not program to customer vehicle, but may program to other vehicles. Other garage door opener remotes may pair to the customer vehicle. This TPI is only valid for cars with "lane change assist" fitted Technical background: Under certain circumstances the radio signal of the customers remote control may not be adapted to the vehicle.

instructions within the Measure section of this TPI in the event that a windscreen is cracked/damaged NOTE: The instructions MUST be followed to help the retailer clarify if the windscreen should be replaced under manufacturers warranty (Stress crack) or Customer pay/insurance (external influence damage) Measure: Identification In the event the windscreen is identified as cracked/damaged it is imperative the inspector of the cracked/damaged screen can determine if the crack was caused by external influences (stone chips) OR the screen is cracked/damaged due to a stress crack

Condition: Warning lamp illuminated within the Driver Instrument Panel (DIP) Drive system fault. Contact your Bentley dealer

Technical background section of this TPI.

Technical background section of this TPI Technical Background: Details on the introduction of E10 fuel which contains 10% ethanol and its usage on Bentley products All vehicles produced post 1990 Model year can be run using E10 fuel However All vehicles produced before 1990 Model year MUST NOT use E10 fuel

Technical Background: The warning lamp and DTCs can be triggered by non-operation of the exhaust flap control unit/s

Customer Statement: Emission control system warning light illuminated within the DIP.

warning light illuminated within the DIP (Figure 1)

to the Technical background section of this TPI

Technical background: Fuel pump control unit 4M0 906 093K has been superseded by fuel pump control unit 4M0 906 093N, however, this change is not currently applicable to Bentley. A small quantity of N level control units were mistakenly issued as spare parts and have subsequently been fitted to Customer vehicles. On vehicles with the -N- level part installed the Customer may complain of noise from the rear seat area, it is possible that fuel pumps may become noisy during operation. At present no other symptoms or faults are expected. Remedy: Correct level fuel pump control unit(s) should be installed 4M0 906 093K

change during a long journey or after refuelling the vehicle and does not show full after filling the fuel tank. No Diagnostic Trouble Code (DTC) stored in Convenience Control Unit for the customer complaint. Technical background: With a customer complaint of Fuel gauge does not change after long journey or after refuelling and does not show full after filling the fuel tank the Symptom-based Guided Fault Finding allows for optimised and specific analysis, this is recommended if no DTC is logged in the convenience control unit.

Customer statement / workshop findings: The washer fluid low warning lamp in the dash insert is lit up although there is sufficient washer fluid in the reservoir. Workshop findings: The customer statement can be reproduced. Technical background The conductibility of the washer fluid can be significantly lowered by the following factors. As a result, the water level switch of the washer fluid low warning lamp can be activated although the washer fluid reservoir is sufficiently full. Washer fluid additives which do not meet the following specification During winter conditions a solution of 30% isopropyl alcohol and 70% water should be used (or appropriate alternative). This washer fluid and water mixture will provide frost protection down to a temperature of approximately 10 degrees C (14 degrees F). Frozen washer fluid. Distilled water.

superseded by fuel pump control unit 4M0 906 093N, however, this change is not currently applicable to Bentley. A small quantity of N level control units were mistakenly issued as spare parts and have subsequently been fitted to Customer vehicles. On vehicles with the N level part installed the Customer may complain of noise from the rear seat area, it is possible that fuel pumps may become noisy during operation. At present no other symptoms or faults are expected. Remedy Correct level fuel pump control unit(s) should be installed 4M0 906 093K.

lit up although there is sufficient washer fluid in the reservoir. Workshop findings: The customer statement can be reproduced. Technical background: The conductibility of the washer fluid can be significantly lowered by the following factors. As a result, the water level switch of the washer fluid low warning lamp can be activated although the washer fluid reservoir is sufficiently full. Washer fluid additives which do not meet the following specification During winter conditions a solution of 30% isopropyl alcohol and 70% water should be used (or appropriate alternative). This washer fluid and water mixture will provide frost protection down to a temperature of approximately 10 degrees C (14 degrees F). Frozen washer fluid. Distilled water.

Customer statement / workshop findings: Complaints relating to My Bentley connected services.

Customer statement / workshop findings: For any interior veneer replacement: raise and obtain approval of a Technical DISS query before ordering. This ensures VIN correct specification and prevents visual mismatch.

Technical background: Conversion of a vehicle for use in a market other than the one for which it was originally designed or intended is not supported. Enquiries related to conversions or retrofits of vehicles from (or to) other markets (e.g. reimport from USA or UK) are not supported by Technical Support. Vehicles are developed and constructed according to specific market requirements of the respective destination country. As the compatibility of different components (e.g. control units) cannot be defined comprehensively regarding their mutual dependence and interaction in the case of modifications, and in order to prevent danger or risks due to constructional changes, support or advice regarding these modifications cannot be provided.

Customer statement / workshop findings: Complaints relating to My Bentley connected services

Condition: For any interior veneer replacement: raise and obtain approval of a Technical DISS query before ordering. This ensures VIN correct specification and prevents visual mismatch.

Customer statement / workshop findings: In the event a customer complaint is received relating to a suspicion that control units or services have been influenced by third parties the instructions within this TPI should be followed. Technical background: A suspicion that control units or services have been influenced by third parties means that unauthorised people or groups may have gained access to a vehicle's control unit(s) or online services and may have manipulated them in such a way that may compromise customer data confidentiality or the operation of the vehicle and/or online services. When investigating potential third party influences of control units or online services, it is important to take all normal diagnostic measures to rule out a normal functional error or misuse of the system by the user

Customer statement / workshop findings: Air vent chrome finisher has detached from vane. Technical background: It is possible that using aftermarket clip on devices such as mobile phone holders, air freshener holders or chewing gum dispensers may result in the chrome air vent finisher becoming detached from the vane. Measure: Please advise the Customer that the use of aftermarket clip on devices is not recommended and continued use may result in repeat failures. Damage caused by the use of aftermarket clip on devices will not be covered under vehicle warranty.

Customer statement / workshop findings: Complaints relating to My Bentley connected services. Technical background: Most queries and complaints regarding My Bentley connected services can be resolved by contacting My Bentley Support rather than raising a DISS technical query.

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Service: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken.

Technical Background: Most queries and complaints regarding My Bentley connected services can be resolved by contacting My Bentley Support rather than raising a DISS technical query.

Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle. Technical Background: The attached document contains all of the current known Spurious DTCs for all vehicle variants. Should a particular TPI be listed as Archived within the attached document the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions with the attached document regarding the DTC description and actions (if any) which should be conducted Service: During routine diagnostic interrogation of vehicle systems use the attached document to determine the course of action to be taken.

and / or Cooling performance has declined over time.

Customer Statement: The customer may find that the A/C system not blowing cold air and / or Cooling performance has declined over time.

Customer Statement: The customer may find that the A/C system not blowing cold air and / or Cooling performance has declined over time.

Customer Statement: The customer may find that the A/C system not blowing cold air and / or Cooling performance has declined over time.

Condition: Customer may report that the air conditioning system is not cooling effectively.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.

expected

Condition Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system

Customer statement: Noise complaint from the suspension and/or steering.

The cover is no longer fitted on replacement water pumps, the cover is not required and MUST not be transferred to the new water pump The operative should fit the new water pump without the cover as shown in Figure 2 NOTE: DISS queries or Service calls should not be submitted for this concern.

fitted directly over the top of the water pump drive gear -However the replacement water pump does not have a cover fitted

Customer statement / workshop findings: The original water pump has a cover fitted directly over the top of the water pump drive gear (Figure 1) However the replacement water pump does not have a cover fitted (Figure 2) Technical background: The cover is no longer fitted on replacement water pumps, the cover is not required and MUST not be transferred to the new water pump The operative should fit the new water pump without the cover as shown in Figure 2 NOTE: DISS queries or Service calls should not be submitted for this concern

Customer statement: Noise complaint from the suspension and/or steering Workshop findings: The noise can be reproduced and clearly assigned to the suspension system from either of the axles And/or The noise can be reproduced and clearly assigned to the steering system

Customer statement/workshop findings: The rear end lowering is intermittently not available and at least one of the two event entries is logged in the running gear control unit (diagnosis address 0074): C11B515 : Button for high load level, interruption/short circuit to positive C11B615 : Button for low load level, interruption/short circuit to positive Technical background: If the button for the rear end lowering is unintentionally operated when driving (for example by objects in the boot), the rear end lowering is sporadically not available. At least one of the two event entries C11B515/ C11B615 is logged.

-The steering column combination switch (J527) has been replaced and DTC U112100 is evident and cannot be cleared

findings: -DTC U103100 with symptom code 3146753 - FlexRay data bus No synchronization evident within diagnostic address 0044

wheel vibration when maneuvering/steering at slow speeds with steering wheel input

the sound file is caused by defective upper inner level bush/bushes. the noise can appear in the following possible scenario -When the vehicle is moved with the steering input over uneven surfaces (for e.g a ramp or speed bump)

the sound file is caused by defective upper inner level bush/bushes. the noise can appear in the following possible scenario -When the vehicle is moved with the steering input over uneven surfaces (for e.g a ramp or speed bump)

Customer statement / workshop findings: Squeaking/creaking noises when steering/manoeuvring or when the suspension compresses and/or: A leak is visible at the boot of the lower ball joint (grease emerging) however the boot does not show any damage Workshop findings: Noises: The noises can be assigned to the lower ball joint on the left and/or right side (Figure 1 - item 20). Leak (grease emerging): Leak at the boot of the lower ball joint on the left and/or right side (Figure 1- item 20) is visible however the boot is undamaged. Technical background: In the event the symptom is as described, the operative should carry out the instructions within the Measure section Make sure that the production date of the new ball joint is 36/19 or later (see date code example circled in Figure 2 - Week 36 of 2019).

Customer statement / workshop findings: When turning the steering wheel a squeaking/droning noise from the location shown in Figure 1 is evident. Technical background: The noise is due to a lack of grease to the intermediate steering shaft bearing which is located within the rubber insulator panel

examples in Figures 1 and 2 showing cracks within the tread pattern)

Background: -The issue is mainly evident on vehicles with very low usage This is a result of the tyre compound hardening due to the following: -Tyre age -Tyre pressure not adjusted to specification -Low mileage/vehicle usage -Vehicle storage conditions

Customer statement / workshop findings: Cracks evident in the sidewall and/or tread pattern (See the examples in Figures 1 and 2 showing cracks within the tread pattern). The issue is mainly evident on vehicles with very low usage This is a result of the tyre compound hardening due to the following: - Tyre age - Tyre pressure not adjusted to specification - Low mileage/vehicle usage - Vehicle storage conditions

Condition: Mottled appearance on A post water deflectors. Surface deposits on A post water deflectors cannot be removed by washing with car shampoo.

The 2G/3G network was deactivated in 2022 within the (North American Region) NAR, therefore a solution has been developed to allow connectivity to the 4G network, connectivity is achieved by fitting additional parts and utilising existing components as detailed within the Work section The procedure within the Work section has been developed to allow connectivity to the 4G network

Technical background: The 2G/3G network was deactivated in 2022 within the (North American Region) NAR, therefore a solution has been developed to allow connectivity to the 4G network, connectivity is achieved by fitting additional parts and utilising existing components as detailed within the Work section. Remedy: The procedure within the Work section has been developed to allow connectivity to the 4G network.

Customer statement / workshop findings: Headlamp operation issues Technical background: DTCs evident within the left light control unit (Diagnostic address D6) and/or the right light control unit (Diagnostic address D7) There are numerous static and intermittent DTCs which may be evident within the previously mentioned control units, ensure all steps within the Measure section are strictly adhered to

cases: Airbag/belt released/not released General accident Fire and scorching damage for all Bentley Vehicle models - every model year.

There is a reporting obligation in the following cases: Airbag/belt released/not released General accident Fire and scorching damage for all Bentley Vehicle models - every model year.

There is a reporting obligation in the following cases: Airbag/belt released/not released General accident Fire and scorching damage for all Bentley Vehicle models - every model year.

seat belt buckle stop button should be evident as shown in Figure 1. Should the seatbelt be as shown in Figure 2 (Buckle stop button missing OR broken/loose) - Refer to the Measure section of this TPI

Customer statement / workshop findings: Netflix application update prompt is shown within the (BYOC) rear seat entertainment system. Technical background: In the event the issue described is evident the operative should conduct the instructions within the Measure section.