2014 Audi RS 5 TSBs
667 Technical Service Bulletins across 17 categories
Categories
Other
180 bulletinsThis bulletin states that technicians are required to report to the manufacturer when a vehicle has flooded, and specify...
Read full bulletin
the height to which the vehicle has been flooded.
This bulletin provides information for reporting safety related information to the manufacturer.
This bulletin provides information when the license plate mounting bracket threded inserts are stripped.
This bulletin provides information when the horn sound quality is poor.
This bulletin provides a statement regarding the bottleneck of supply for VW approved oil types VW 504.00 and VW 507.00.
This bulletin provides information when there are noises from the area around the instrument cluster.
This bulletin provides informationwhen noises/vibration are detected from front of vehicle in dynamic mode.
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
This bulletin provides diagnostic information for the vehicle locking system.
This Reporting obligation requests that technicians contact the Technical Assistance Center (TAC) when the diagnostic...
Read full bulletin
tester refers to this reportin gobligation or to TPI 2033392.
This bulletin provides informaiotn about various infortainment system complaints.
This bulletin provides information when the parking assistance gives false warnings.
This bulletin provides information when the parking assistance gives false warnings.
This TSB provides information when there are noises from the area around the instrument cluster.
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
This bulletin provides information regarding contact checks for event memories, intermittent.
This bulletin provides information when the anti-theft alarm activates for no reason, or does not activate.
This bulletin provides information on VIN Plates, Safety Certification labels, and the ordering procedures.
This bulletin provides information on searching for noises on vehicles with Dynamic Ride Control.
This bulletin provides informaiton when the license plate mouting bracket threaded inserts are stripped.
This bulletin provides information for when there is a fluid sample request from Product Support.
This bulletin provides information when the horn sound quality is poor.
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does...
Read full bulletin
not activate.
This TSB is a label placement guide as required by CARB for remanufactured parts.
This TSB provides damage assessment guidelines for textile seat covers.
This TSB is a label placement guide as required by CARB for remanufactured parts.
This bulletin provides information about leather care and seat repair.
This bulletin provides informationw hen there are optical defects, scratches, and/or chrome peeling.
This bulletin provides information in circumstances where there are noises/vibration from front of vehicle in dynamic...
Read full bulletin
mode.
This bulletin provides information when the anti-theft alarm activates for no reason, or when the anti-theft alarm does...
Read full bulletin
not activate.
This TSB Provides information when parking assistance provides false warnings.
This bulletin provides information about professional noise analysis with the VAS 611 015 PICO-NVH tool
This bulletin provides diagnostic information regarding the locking system.
This bulletin provides information on searching for noises on vehicles with Dynamic Ride Control.
This bulletin provides guidance in order to provid informaiton regarding preparatoin when calling the Audi Technical...
Read full bulletin
Assistnce Center (TAC).
This bulletin offers information about the basic information needed for technical requests for gaerbox complaints.
This bulletin offers information about the basic information needed for technical requests for gaerbox complaints.
This bulletin provides information when there are noises/vibration from the front of the vehicle while in dynamic mode.
This bulletin provides Audi technicians with information to prepare for contact to the Technical Assistance Center...
Read full bulletin
(TAC).
This bulletin provides information for when there is a fluid sample request from Product Support.
This bulletin provides information on the ordering procedures for VIN Plates, and Safety Certification labels.
This bulletin provides information for when there is a fluid sample request from Product Support.
This bulletin provides information on the ordering procedures for VIN Plates, and Safety Certification labels.
This bulletin provides general information regarding outside air temperature readings.
This bulletin provides information when there is noise from around the instrument cluster.
This bulletin provides information when the remote control key is inoperative.
This bulletin provides information for when DTC P0A7D00 is stored.
Repair Authorization
Repair Authorization.
Repair Authorization
Elsa newsletter
Vehicle condition report
Vehicle detail report
Technician report
Audi delivery guidelines
Google Maps Street View (NVLW))
This bulletin provides information when the parking assistance provides false warnings.
This bulletin provides general information about the outside air temperature reading.
This bulletin provides information for when the license plate mounting bracket threaded inserts are stripped.
This bulletin provides information on the VAS 611 015 PICO-NVH tool for professional noise analysis.
This bulletin provides damage assessment guidelines for textile seat covers.
This bulletin provides instructions regarding unauthorized chip tuning (TD1).
This bulletin provides information for when unauthorized/unjustified DTC memory entries are captured in ODIS test Plans...
Read full bulletin
(Ghost faults).
Elsaweb Newsletter
This bulletin provides information on the additional reporting requirements for safety related inquiries.
Audi Oil Capacity Chart
Tabla de presin de los neumticos de condicin de carga normal para Audi modelo 2014
Informe del tcnico de Audi
Informe del tcnico de Audi
Informe del tcnico de Audi
Lineamientos de entrega de Audi
Audi Elsa Newsletter
Audi Elsa Newsletter
Audi Elsa Newsletter
Audi Elsa Newsletter
Audi Elsa Newsletter
Audi Elsa Newsletter
Audi Elsa Newsletter
Audi Elsa Newsletter
This bulletin provides information on workshop mode with Audi connect vehicles.
This bulletin provides information on professional noise analysis with the VAS 611 015 PICO NVH Tool.
This bulletin provides information for when the washer solvent level warning is on.
This bulletin provides information for when there is noise from the area around the instrument cluster.
This bulletin provides information for when an unpleasant odor is coming from the heating and ventilation system.
This bulletin provides information for when an unpleasant odor is coming from the heating and ventilation system.
This bulletin provides information regarding the Audi advanced key.
This bulletin contains instructions for noises on uneven roads using chassis ears or the PICO tool.
This bulletin provides instructions for when the washer level warning is on but the reservoir is full.
This bulletin provides instructions for ordering replacement Safety Certification labels or VIN plates.
This bulletin provides information for when the customer advises that there is cracking, grinding, rattling, humming,...
Read full bulletin
whining, or similar interference.
This information bulletin contains a background on the outside air temperature reading.
This bulletin contains instructions for noises on uneven roads using chassis ears or the PICO tool.
This bulletin provides instructions for when the anti-theft alarm has gone off for no reason, or did not go off at all.
Read full bulletin
No DTCs are stored.
This bulletin provides instructions for when the washer solvent level warning is on in the DIS but the washer solvent...
Read full bulletin
level is correct.
This special notice is to inform dealers to return the parts listed only order the successor parts going forward.
Hesitation after deceleration at lower speeds
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
This bulletin contains instructions for noises on uneven roads using chassis ears or the PICO tool.
Vibrations felt at 1000 rpm and 3000 rpm
Vibrations felt at 1000 rpm and 3000 rpm
This bulletin contains information on noises from the instrument cluster installation area.
This bulletin contains instructions for properly cleaning and removing a musty odor from the heating and ventilation...
Read full bulletin
system.
This is an informational bulletin containing information about the outside temperature reading.
Dealer Communication: Vehicle Sales Reporting, Reinstatement, and Audit Policy
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't...
Read full bulletin
exist or it is inoperative/constant warning.
This bulletin contains instructions for identifying and mixing factory fill coolants.
This bulletin contains instructions for identifying and mixing factory fill coolants.
Audi Delivery Guidelines.
Several weeks ago, the ODIS Quick Reference Guide was sent to all dealer technicians (non-corporate
This informational bulletin gives instructions for identifying chip tuning.
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant...
Read full bulletin
expansion tank cap.
This informational bulletin explains how to order replacement VIN plates, Safety Certification Labels, etc.
This information bulletin states to remove the car wash bristle and advise the customer to go somewhere else to prevent...
Read full bulletin
it from occurring again.
This special notice is to inform dealers to return the parts listed if it meets the criteria provided.
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't...
Read full bulletin
exist or it is inoperative/constant warning.
This bulletin contains instructions for determining unexpected Audi presense interventions.
This bulletin contains information on noises from the instrument cluster installation area.
This information bulletin contains a background on the outside air temperature reading.
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
This bulletin contains instructions for determining if a repair is needed when coolant touches a poly V-belt and/or a...
Read full bulletin
toothed belt.
This informational bulletin contains instructions on how to download and use the Audi Frequency App.
This informational bulletin covers the condition of when license plate mounting bracket threaded inserts are stripped.
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't...
Read full bulletin
exist or it is inoperative/constant warning.
This informational bulletin contains instructions for Audi connect before performing any MMI work.
This special notice is to inform dealers to return the part numbers listed (State of California only).
This information bulletin contains instructions for technicans on how to ensure their TAC call goes smoothly.
Added new graphic to reflect where to find MY 21 information
This information bulletin contains a background on the outside air temperature reading.
This bulletin contains instructions for identifying and mixing factory fill coolants.
This bulletin contains instructions for correcting the phonebook.
This informational bulletin contains instructions on how to use the QR code in a TSB.
This bulletin contains information on noises from the instrument cluster installation area.
This information bulletin contains a background on the outside air temperature reading.
This bulletin contains a cleaning procedure from leftover residue from suction cups or labels.
New document 2004-2020 A4 allroad, A6 allroad, A8L, R8 Spyder
This bulletin contains instructions for enabling text message notifications through the MMI system.
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't...
Read full bulletin
exist or it is inoperative/constant warning.
This bulletin contains instructions for when the anti-theft alarm went off for no reason or did not go off.
Read full bulletin
Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.
This bulletin provides repair instructions for when DTC P209600 and DTC P209800 appear and the reference duct is...
Read full bulletin
contaminated.
This informational bulletin contains instructions for setting up and using the SD creator program.
This special notice is to inform dealers to return all part numbers listed in the document and order the superseded part...
Read full bulletin
numbers going forward.
This bulletin contains instructions on a repairing an issue when the GPS does not have the correct location or...
Read full bulletin
reception.
This bulletin contains continued instructions after completing 2041097.
This is a communication on the targeted allocation process.
3.0L TDI Gen 2-PC_Customer letter
3.0L TDI Gen 2-PC_Booklet
This informational bulletin contains all the the Audi Oil Quality Standards that should be used when doing an oil...
Read full bulletin
change.
This is an information bulletin regarding procedure for when the technician finds coolant marks during a repair.
This bulletin contains instructions on how to fix when the GPS does not have the correct location or reception.
This technical bulletin provides instructions for an an error message and updating with an SVM code.
This bulletin contains technical information regarding when the parking aid sporadically warns of obstacles that don't...
Read full bulletin
exist or it is inoperative/constant warning.
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant...
Read full bulletin
expansion tank cap.
This document contains the fluid capacity chart.
This document contains the Audi delivery guidelines checklist.
This document contains the fluid capacity chart.
This document contains the Audi oil capacity chart.
This document contains the Audi vehicle condition report checklist.
This document contains the Audi vehicle detail report checklist.
This document contains the Audi delivery guidelines checklist.
This document contains the Audi delivery guidelines checklist.
This document contains the Audi delivery report checklist.
Read full bulletin
This document is in Spanish.
This document contains the Audi delivery report checklist.
Read full bulletin
This document is in Spanish.
This bulletin provides repair information for when DTC P209600 and DTC P209800 appear and the reference duct is...
Read full bulletin
contaminated.
This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant...
Read full bulletin
expansion tank cap.
This bulletin provides repair information for when DTC P209600 and DTC P209800 appear and the reference duct is...
Read full bulletin
contaminated.
Audi connect Gen1 and Gen2 systems: Differences and troubleshooting.
Read full bulletin
The customer has a general concern related to Audi connect. Different features are included with different generations of the Audi connect system. The Audi connect Gen1 system includes all vehicles that utilize a removable plastic SIM card. The Audi connect Gen2 system includes all vehicles that utilize an embedded SIM card. The root cause of all complaints cannot be attributed to the vehicle hardware because of the backend server configurations that need to be correct in order for Audi connect to work. For most sporadic complaints, the issue typically resides with the MBB backend server or with the source data provider (Google, INRIX, etc.), and not with the vehicle. In rare cases, the mobile network operator (AT&T, T-Mobile) can be the cause of the complaint. For most static complaints, the issue can be attributed to the user account subscription or possibly the vehicle hardware.
THIS BULLETIN CONTAINS INSTRUCTIONS ON HOW TO FIX WHEN THE GPS DOES NOT HAVE THE CORRECT LOCATION OR RECEPTION.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
SUMMARY TO BE PROVIDED ON A FUTURE DATE.
Engine
81 bulletinsThis bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
This bulletin provides informaiton when the engine is not running smoothly, misfiring.
This bulletin provides information regarding UV leak additive for finding oil leaks.
This bulletin provides information on the zirconium insercts in the brake piston (ceramic brakes only).
This bulleitn provides information regarding UV Leak additive for finding oil leaks.
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
This bulletin provides information when the MIL is on; DTCs for misfire, air/fuel ratio imbalance, or lean fuel system...
Read full bulletin
stored in the ECM P030000.
This bulletin provides informatin when the engine does not run smoothly at idling speeds.
This bulletin provides informaion regarding zirconium inserts in the bake piston for vehicle equipped with ceramic...
Read full bulletin
brakes.
This bulletin provides information when ther is an Engine: start/stop system fault shown and start/stop system not is...
Read full bulletin
working; mileage below 50 km/32 miles.
This bulletin provides information when there is a fault shown; Engine: start/stop system, and the start system is not...
Read full bulletin
working; mileage below 50 km/32 miles.
Idle speed characteristic during cold start
Idle speed characteristic during cold start
The Audi 2.0L Third Generation TDI Engine
This bulletin provides information on checking for debris when replacing an engine.
This bulletin provides information on the discontinuation and mixing of Audi-approved engine coolants.
Idenifying and mixing factory fill engine coolants
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
Read full bulletin
When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows...
Read full bulletin
that the oil level is not okay.
Bump after coming to a stop or rattle noise from transmission at idle speed
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows...
Read full bulletin
that the oil level is not okay.
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay.
Read full bulletin
When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows...
Read full bulletin
that the oil level is not okay.
The DTC is caused by conflicting tolerances of the fuel pump at idle speed/part load.
Engine oils that meet Audi Oil Quality Standards.
A small amount of dry or crusted coolant is seen on the coolant pump housing (Figure 1, Figure 2, and Figure 3).
Read full bulletin
The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not...
Read full bulletin
available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not...
Read full bulletin
available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
The programmed values for the misfire adaption are not automatically reset when the memory is deleted.
Read full bulletin
The adaption must be reset after the engine is installed.
DTC P218100 will be stored if, after a specified air flow (warm-up phase), the measured engine temperature does not reach the value in the timing map.
Read full bulletin
Particles in the cooling system from the production process affect the closing of the coolant thermostat.
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously.
Read full bulletin
Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).
This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously.
Read full bulletin
Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. As a result, application of the brake and accelerator pedals at the same time (brake pedal with left foot and accelerator pedal with right foot) results in the following: ? Brake pedal function (normal at all times) overrides any throttle application. ? Diagnostic Trouble Codes (DTCs) will not be stored. ? When the brake pedal is applied while the accelerator is depressed, engine RPMs will return to idle speeds of 1400 RPMs after approximately two seconds. ? When the accelerator is applied while the brake pedal is depressed, the vehicle accelerates slower than usual (reduced engine torque).
This bulletin contains instructions for using the UV additive to find engine oil leaks.
This technical service bulletin reminds the reader to check for metal debris when replacing an engine.
This bulletin contains instructions for using the UV additive to find engine oil leaks.
This bulletin contains instructions for using the UV additive to find engine oil leaks.
Important Information Regarding Approved Emissions Modification (TDI) Recall Campaigns & the California Air Resources...
Read full bulletin
Board / Department of Motor Vehicle (DMV) Vehicle Registration Requirement
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to...
Read full bulletin
4,000rpm, and there are DTCs about the intake manifold flap adjustment.
Supersedes Technical Service Bulletin Group 30 number 11-10 dated December 2, 2011.
Read full bulletin
Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.
The MIL is on. Customer may report that the engine runs irregularly.
Read full bulletin
DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. They are gathered by the oil filter.
Supersedes Technical Service Bulletin Group 19 number 14-50 dated June 20, 2014.
Read full bulletin
Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
This technical service bulletin provides instructions for troubleshooting and repairing the camshaft adjustment valve...
Read full bulletin
to correct a concern about the engine running irregularly.
This bulletin provides instructions for a slow coolant leak from coolant connections.
This bulletin contains repair instructions for when a 4.0 liter engine has a MIL on, the engine may be limited to...
Read full bulletin
4,000rpm, and there are DTCs about the intake manifold flap adjustment.
Vibrations are felt at 1000 rpm and 3000 rpm.
Read full bulletin
DTCs are stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off.
Supersedes Technical Service Bulletin Group 87 number 12-27 dated April 24, 2012.
Read full bulletin
There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.
Bump felt just after the vehicle is brought to a stop.
Read full bulletin
Rattle noise heard from transmission at idle speed. The software of the transmission mechatronic control module, J743, needs to be updated.
Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012.
Read full bulletin
Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies.
Steering wheel lock does not work.
Read full bulletin
Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. DTC with description "Brake control unit, no signal/communication" is present in several control units. DTC entry in ABS Control unit, J104 (03). One or more may be present. This condition does not result in any drivability concerns. The steering system is fully connected. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.
This document contains the important email to all Audi dealership personnel in regards to the immediate madatory...
Read full bulletin
stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.
Supersedes Technical Service Bulletin Group 35 number 13-12 dated June 18, 2013.
Read full bulletin
Customer may report that there is oil leaking under the vehicle. Leaking from the oil pan seal. Crack in the oil pan. Leak between gearbox housing and intermediate housing. The source of the leak may be confused with o-ring of drain plug.
Supersedes Technical Service Bulletin Group 20 number 15-52 dated October 28, 2015.
Read full bulletin
The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
Supersedes Technical Service Bulletin Group 20 number 15-48 dated October 15, 2015.
Read full bulletin
The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
Supersedes Technical Service Bulletin Group 20 number 15-46 dated May 15, 2015.
Read full bulletin
The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.
The red coolant light is illuminated, indicating that the coolant temperature is too high or that the coolant level is too low.
Read full bulletin
The engine speed governing light is illuminated with the message ?Engine speed maximum XXXX rpm?. To prevent the engine from overheating, the engine speed is automatically limited to the displayed maximum. DTCs are stored in the ECM. Tolerances of opening spring in thermostat cause the condition.
This document contain information on the upcoming emissions service action 17F9 in regards to the crankcase pressure...
Read full bulletin
regulating valve.
On certain Audi vehicles with 2.0L TFSI engine, the diaphragm of the crankcase pressure regulating valve may have been damaged.
Read full bulletin
Inspect and, if necessary, install a repair kit for the crankcase pressure regulating valve.
On certain Audi vehicles with 2.0L TFSI engine, the diaphragm of the crankcase pressure regulating valve may have been damaged.
Read full bulletin
Inspect and, if necessary, install a repair kit for the crankcase pressure regulating valve.
Supersedes Technical Service Bulletin Group 01 number 12-51 dated July 18, 2012.
Read full bulletin
Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperature of the exhaust gas and of the catalyst increases quickly. The afterburning in the exhaust manifold before catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase the engine has increased idle speed, may have increased vibrations, and a different sound characteristic. Depending on conditions the time of the catalyst heating phase varies.
The customer may state that the outside ambient temperature display is incorrect.
Read full bulletin
To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4 F (2 C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.
Customer may report that the check engine light comes on intermittently.
Read full bulletin
DTC P310B00 DFC 2638 (Low fuel pressure regulation fuel pressure outside specification) is stored in the engine control module (ECM). The DTC is caused by conflicting tolerances of the fuel pump at idle speed/part load.
Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013.
Read full bulletin
Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.
Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013.
Read full bulletin
Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013.
Read full bulletin
Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
The MIL is on. DTC P310B00 (DFCC 2638) (Low fuel pressure regulation, fuel pressure outside specification) is stored in...
Read full bulletin
the engine control module, J623 (address word 01). DTC P310B00 (DFCC 2638) can be caused by quantity deviations of the fuel pump.
Supersedes Technical Service Bulletin Group 17 number 14-53 dated November 7, 2014.
Read full bulletin
A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.
Rattling noises are heard from the timing chain drive for about 1-3 seconds after the first engine start of the day.
Read full bulletin
The noises are caused by one of the upper chain tensioners. The noises do not lead to damage. Improved chain tensioner.
Customer may report that the check engine light comes on intermittently.
Read full bulletin
Low fuel pressure regulation fuel pressure outside specification DTC is stored in the ECM. The DTC is cause by conflicting tolerances of the fuel pump at idle speed/part load.
This bulletin provides a SVM code update for in Engine Control Module.
This bulletin contains software update information for the transmission when a bump can be felt just after the vehicle...
Read full bulletin
is brought to a stop or when a rattle noise is heard at idle speed.
This bulletin contains detailed instructions and a worksheet for determining the damage on a turbocharger.
The red coolant light is illuminated , indicating that the coolant temperature is too high or that the coolant level is too low.
Read full bulletin
The engine speed governing light is illuminated with the message " Engine speed maximum XXXX rpm". To prevent the engine from overheating, the engine speed is automatically limited to the displayed maximum. DTCs are stored in the ECM due to the problem. Tolerances of opening spring in thermostat cause the condition.
The MIL is sporadically on.
Read full bulletin
One or more of the following DTCs is stored in the engine control module (ECM, J623 (address word 01). They are DTC P261A00 (Coolant Pump ?B? Control Circuit/Open), DTC P261B00 (Coolant Pump ?B? Control Circuit Range/Performance), and DTC P261C00 (Coolant Pump ?B? Control Circuit Low). The continued coolant circulation pump sporadically fails.
ON CERTAIN AUDI VEHICLES WITH A 3.0L TFSI ENGINE MANUFACTURED DURING A SPECIFIC PERIOD, THE DIAGNOSTIC THRESHOLDS FOR...
Read full bulletin
THE CATALYTIC CONVERTERS WERE PROGRAMMED TOO TIGHTLY IN THE ENGINE CONTROL UNIT. AS A RESULT, THE MALFUNCTION INDICATOR LIGHT (MIL) MAY COME ON EVEN THOUGH THE CATALYTIC CONVERTERS ARE WORKING PROPERLY. IF THE MIL IS ON, A VEHICLE WILL NOT PASS AN EMISSIONS INSPECTION.
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC...
Read full bulletin
P046100 IN VEHICLES WITH V8 ENGINES.
THIS TECHNICAL SERVICE BULLETIN NOTIFIES THE READER THAT IF THE TPMS MESSAGE APPEARS BRIEFLY AFTER THE ENGINE IS STARTED...
Read full bulletin
AND THEN DISAPPEARS, IT DOES NOT INDICATE AN ISSUE WITH THE TPMS SYSTEM.
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC...
Read full bulletin
P046100 IN VEHICLES WITH V8 ENGINES.
THIS IS AN INFORMATION BULLETIN THAT DESCRIBES CASES WHERE SOME CLICKING OR TICKING NOISES CAN BE HEARD IN THE ENGINE...
Read full bulletin
COMPARTMENT.
THIS TECHNICAL SERVICE BULLETIN INFORMS THE READER THAT THERE IS A PENDING SERVICE SOLUTION (PSS) FOR MIL ON WITH DTC...
Read full bulletin
P046100 IN VEHICLES WITH V8 ENGINES.
AUDI: ENGINE, ON SOME VEHICLES, WOULD RUN IRREGULARLY OR HAVE MALFUNCTION INDICATOR LAMP (MIL) ON OR POSSIBLE FILTER...
Read full bulletin
ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE
2013-2014 AUDI RS5 AND RS5 CABRIOLET MAY BE EXPERIENCING INTERMITTENTLY ENGINE LIGHT MALFUNCTION AND THE FUEL PRESSURE IS OUTSIDE THE SPECIFICATION.
Read full bulletin
*CW
Brakes
61 bulletinsThis bulletin provides information about the general approach for brake vibration concerns.
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
This bulletin provides information for all models regarding brake sounds.
This bulletin provides information for all models regarding brake sounds.
This bulletin provides information regarding the general approach for all Audi vehicles regarding brake vibrations.
This bulletin provides information when there is an ABS/ESC speed sensor implausible signal.
This bulletin provides information regarding the general approach to brakes rubbing.
This bulleitn provides information when there is an implausible signal in the ABS/ESC speed sensor.
Brake noise analysis and handling
Ceramic brake repair authorization.
Brake pulsation diagnostic guidelines
Ceramic brake repair authorization
Shock absorber leaks: assessment aid
Shock absorber leaks: assessment aid
This bulletin provides information for when the ABS/ESC speed sensor has an implausible signal.
This bulletin provides information for when one or more DC is stored in the ABS control unit related to the parking...
Read full bulletin
switch; DTC C100C07 and/or C100C29.
This bulletin provides information for when there are noises when braking, and the brake pad thickness is OK.
This bulletin provides instructions for brake noise analysis and handling.
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
ABS warning light on - wire harness damage
This technical service bulletin provides troubleshooting for brake noise.
This technical service bulletin provides troubleshooting for brake noise.
Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
The customer reports feeling a hesitation when accelerating the vehicle at lower vehicle speeds (4-10 mph).
Read full bulletin
This condition is normally noticed after braking or deceleration from higher speeds (30 mph or higher), and it lasts for less than one second. Optimized software.
This bulletin contains instructions for diagnosing noises from the suspension with an oil film on the shock absorbers.
This technical service bulletin provides troubleshooting for brake noise.
This informational bulletin provides diagnostic information for brake conditions.
This technical service bulletin provides troubleshooting for brake noise.
This bulletin contains instructions for diagnosing noises from the suspension with an oil film no the shock absorbers.
This informational contains an explanation for when the customer hears creaking noises when braking at almost standstill...
Read full bulletin
(crawling when pulling away or briefly before standstill).
This technical service bulletin provides troubleshooting for brake noise.
This informational bulletin provides diagnostic information for brake conditions.
This bulletin contains instructions for diagnosing noises from the suspension with an oil film on the shock absorbers.
This bulletin contains repair instructions for leaking shock absorbers.
This technical service bulletin provides troubleshooting for brake noise.
This technical service bulletin provides troubleshooting for brake noise.
Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc ...
Read full bulletin
temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.
This informational bulletin contains knowledge on why oil may appear on one or several of the shock absorbers.
This informational bulletin contains technical information for when there is condensation visible on the inside of the...
Read full bulletin
headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.
This informational bulletin contains instructions for proper brake maintenance.
Supersedes Technical Service Bulletin Group 46 number 14-67 dated January 21, 2014.
Read full bulletin
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. This TSB should not be used if another brake noise TSB is available for the vehicle. For additional helpful information, refer to the Audi Brake Systems brochure.
Supersedes Technical Service Bulletin Group 46 number 13-53 dated August 7, 2013.
Read full bulletin
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
Customer may report that the ceramic brakes are noisy.
Read full bulletin
Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts.
Supersedes Technical Service Bulletin Group 46 number 14-76 dated March 25, 2014.
Read full bulletin
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
Supersedes Technical Service Bulletin Group 46 number 14-79 dated April 14, 2014.
Read full bulletin
Customer may report that the ceramic brakes are noisy. PR codes are affected.
Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013.
Read full bulletin
Oil appears on one or several shock absorbers.
Supersedes Technical Service Bulletin Group 37 number 13-16 dated September 3, 2013.
Read full bulletin
The customer reports feeling a hesitation when accelerating the vehicle at lower vehicle speeds (4-10 mph). This condition is normally noticed after braking or deceleration from higher speeds (30 mph or higher), and it lasts for less than one second.
Supersedes Technical Service Bulletin Group 46 number 13-44 dated June 11, 2013.
Read full bulletin
Customer may report that the ceramic brakes are noisy. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.
Supersedes Technical Service Bulletin Group 46 number 14-68 dated February 3, 2014.
Read full bulletin
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
Supersedes Technical Service Bulletin Group 46 number 14-64 dated January 2, 2014.
Read full bulletin
Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.
Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012.
Read full bulletin
Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.
Customer may report hearing brake noise from front or rear brakes.
Read full bulletin
Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.
Customer may report hearing brake noise from front or rear brakes.
Read full bulletin
Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
Supersedes Technical Service Bulletin Group 46 number 14-85 dated July 14, 2014.
Read full bulletin
A TAC ticket must be opened for any repairs related to the ceramic brakes. Various parts have been replaced under warranty for the condition noted above, but no issues were identified with these parts. In an effort to gain information, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts.
Supersedes Technical Service Bulletin Group 46 number 15-00 dated January 23, 2015.
Read full bulletin
The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.
The customer may report hearing brake noise from front or rear brakes.
Read full bulletin
The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time
This bulletin should be used when performing RS5 front brake repairs.
The customer may report hearing brake noise from front or rear brakes.
Read full bulletin
The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. Aftermarket pads or discs have been installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time.
AUDI: THE CERAMIC BRAKES ON VEHICLES ARE VERY NOISY AND NEED REPLACING AND WHILE UNDER WARRANTY, VARIOUS PARTS HAVE BEEN REPLACED.
Read full bulletin
*PE
AUDI: ON CERTAIN VEHICLES, USE CALIBRATED TORQUE WRENCH AND NOT TORQUE STICKS, TORQUE EXTENSION BARS AND IMPACT...
Read full bulletin
GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE
AUDI: SOME VEHICLES MAY LACK POWER OR WILL NOT MOVE AFTER STOP DUE TO SIMULTANEOUSLY DEPRESSING THE BRAKE AND ACCELERATOR PEDALS.
Read full bulletin
*JS
Electrical
52 bulletinsThe high-voltage batteries in electric vehicles are subject to various ageing effects which could lead to the energy...
Read full bulletin
content (energy density) being reduced. This reduction in the energy content, which is due to factors. Revised header. Added Model years
This bulletin provides additoinal information to assist in determining the energy content of lithium-ion high-voltage...
Read full bulletin
batteries.
This is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle...
Read full bulletin
programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.
This TSB provides information when the Audi advanced key is inoperative; door handle touch sensors.
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
This bulletin provides service-info relating to lithium-ion high-voltage batteries; determining energy content.
This bulletin provides information when the door handle touch sensors for Audi advanced key are inoperative.
This bulletin provides information when the door handle touch sensors for Audi advanced key are inoperative.
AC Pressure/Temperature Sensor
AC Pressure/Temperature Sensor
AC Pressure/Temperature Sensor
AC Pressure/Temperature Sensor (NVLW)
AC Pressure/Temperature Sensor (NVLW)
AC Pressure/Temperature Sensor
i-wire new wiring diagram application
Support for Customers Affected by Alternator Back-order
Support for Customers Affected by Alternator Back-order
Support for Customers Affected by Alternator Back-order
Support for Customers Affected by Alternator Back-order
Support for Customers Affected by Alternator Back-order
Support for Customers Affected by Alternator Back-order
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated.
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated.
The customer complains of one or more of the following issues: ? When the vehicle is completely refueled, the vehicle...
Read full bulletin
range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.
Customer vehicle is fitted with unauthorized ECM tuning.
Low battery charge: excess current draw location
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM.
Read full bulletin
This document also applies to the 2015 A3 Cabriolet and the 2015 A4 Cabriolet.
This bulletin contains repair instructions for when the MIL is on and the DTC P045600 is stored in the ECM.
Read full bulletin
Vehicles also include 2015 A3 Cabriolet and 2012 RS7,
Due to increasing requests for high voltage personal protective equipment (HVE PPE) for dealer technicians working with...
Read full bulletin
high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.
This technical service bulletin provides instructions for diagnosing an issue with the G676 sensor module and replacing...
Read full bulletin
it.
Supersedes Technical Service Bulletin Group 57 number 13-86 dated March 20, 2013.
Read full bulletin
The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
This Update has been proactively released to prevent the following condition from occurring in the vehicle.
Read full bulletin
On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.
This Update has been proactively released to prevent the following condition from occurring in the vehicle.
Read full bulletin
On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.
Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012.
Read full bulletin
The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
The adaptive damping suspension control module, J250, cannot be coded via SVM spec/actual after it has been replaced.
Read full bulletin
A new generation of the adaptive damping suspension control module, J250, was placed into production. The new generation control module must be coded and parameterized using an SVM code, which is listed in the attached ETKA Parts Bulletin, 9-119. This parts bulletin can be found in the ETKA Remarks for the part number.
A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated.
Read full bulletin
This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.
Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012.
Read full bulletin
After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or parameterized via an SVM specified vs. actual comparison (spec/actual). The parameter data in the software coding container has changed for the front and rear door control units. As a result, an SVM code is required to update the parameter data for any replacement control unit. Simply running an SVM spec/actual will not code nor update the parameter data in the new replacement control unit. A hardware change suggestion will be provided when an SVM spec/actual is executed. An additional hardware replacement is not required.
On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time.
Read full bulletin
As a result, the air conditioner compressor is switched off. This Update is in effect until removed. Procedure is valid only for vehicles that show the 87D9 code in the Elsa Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off.
Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013.
Read full bulletin
After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. If the SVM code was not acquired through the GP bulletin in ETKA, follow the instructions in the Service section of this bulletin to update the control module.
This document contains the Audi technician report checklist.
Read full bulletin
All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection.
This document contains the Audi technician report checklist.
Read full bulletin
All items must be completed prior to customer delivery by an Audi technician. Refer to the Special functions tab of ODIS Diagnosis using GFF for the PDI function tests. Audi recommends using an Audi approved battery charger to prevent excessive battery discharge during inspection.
Supersedes Technical Service Bulletin Group 91 number 14-50 dated July 10, 2014.
Read full bulletin
Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.
Update ECM software to improve diagnostic of NVLD system.
When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes Briefly after the initial...
Read full bulletin
Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded. When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. When music is streamed to the MMI system with the Bluetooth A2DP connection, the music intermittently pauses or seems to skip. The condition goes away once the phonebook transfer is completed. The MMI uses a limited portion of the total memory to convert the name and phone number fields of downloaded contacts into a voice command (text to speech). Extensive processing takes place if too many letters are used in the first and last name fields or if numbers or special characters are entered. The remaining memory is dynamically assigned to different applications which can also affect the capacity of the voice command processing. The MMI does not respond until the process is completed or it may freeze if phonebook fields are too large or do not follow typical formatting. In addition, the text-to-speech capacity is exceeded and the voice recognition system is rendered inactive.
Update ECM software to improve diagnostic of NVLD system.
Read full bulletin
Bulletin revised to update claiming instructions.
The message "Oil minimum warning, add one quart of oil" appears in the instrument cluster, but the oil level is above the minimum level.
Read full bulletin
There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.
TSBs in this newsletters include the MIL on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency...
Read full bulletin
below threshold) being stored in the ECM. New ECM software implemented to correct the condition.
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR DIAGNOSING AN ISSUE WITH THE G676 SENSOR MODULE AND REPLACING...
Read full bulletin
IT.
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR UPDATING THE ECM SOFTWARE TO CORRECT AN ISSUE THAT CAUSES DTC...
Read full bulletin
P310B00.
THIS TECHNICAL SERVICE BULLETIN EXPLAINS HOW TO UPDATE THE ECM SOFTWARE TO CORRECT AN ISSUE THAT CAUSES DTCS P0300,...
Read full bulletin
P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308.
AUDI: SOME VEHICLES, IN COLD WEATHER, OCCASIONALLY, CANNOT BE UNLOCKED USING THE DOOR HANDLE TOUCH SENSOR.
Read full bulletin
ALSO INCLDED ARE MODEL A4 MY 2014, MODEL A5 CABRIOLET MY 2014, MODEL Q5 MY 2014, MODEL RS5 CABRIOLET MY 2014, AND MODEL S5 CABRIOLET MY 2011-2014. *JS
Infotainment
38 bulletinsThis bulletin provides information when there are speaker rattles, vibrations, or audio interference.
This bulleitn provides information whent here are complaints about route guidance with Navigation.
This bulletin provides information regarding various comlaints related to Apple CarPlay with Apple iOS devices.
This bulletin provides information when speaker rattles, vibrations, or audio interference is noted.
This bulletin proves information when the bluetooth does not work, adaption channel deactivated.
This bulletin proves information when the bluetooth does not work, adaption channel deactivated.
This bulletin provides informaiton when there are speaker rattles, vibrations or audio interference in the sound system.
This bulletin provides informaiton when there are speaker rattles, vibrations, or audio interference.A1
This bulletin provides information when there are speaker rattles, vibration or audio interference.
This bulletin provides informaiton when there are speaker rattles, vibrations, or audio interference.A1
This bulletin provides information when there are speaker rattles, vibration or audio interference.
This bulletin provides information pertaining to MMI Navigation database concerns.
This bulletin provides information for when the customer has concerns about the navigation route guidance.
This bulletin provides information on how to update the navigation map.
This bulletin advises that the MMI screen may freeze, or go blank and then restart when a special character like a...
Read full bulletin
symbol or emoticon is used in the name field for contact(s).
This informational bulletin contains instructions for when the message "Audi pre sense currently restricted.
Read full bulletin
See owner's manual" is displayed in the instrument cluster without DTCs.
This informational bulletin contains instructions about updating the navigation map.
The navigation DVD or other CD/DVD cannot be ejected.
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
Elsa2Go campaign information is now 100% aligned with ElsaPro.
Read full bulletin
This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.
This informational bulletin contains instructions about updating the navigation map.
This bulletin contains repair instructions for voice recognition or Bluetooth quality issues that are related to the...
Read full bulletin
microphone.
This informational bulletin contains instructions about updating the navigation map.
This informational bulletin explains when the range display is empty in the on-board computer.
This technical service bulletin provides troubleshooting for issues with the navigation map database.
This informational bulletin contains instructions for when a phone is connected to the vehicle via Bluetooth, one of the...
Read full bulletin
following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.
This bulletin contains inspection guidelines for radio interference that causes noises in the speaker.
This informational bulletin explains when the range display is empty in the on-board computer.
Read full bulletin
Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro
This bulletin contains software update ifnormation for when the instrument cluster display shows ?Please reduce oil...
Read full bulletin
level.?
This informational bulletin contains resource information for when the traffic feature is inoperative in the MMI...
Read full bulletin
navigation.
Supersedes Technical Service Bulletin Group 91 number 15-10 dated August 25, 2015.
Read full bulletin
When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue resolves itself intermittently. No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). (Q7 and Q3 vehicles are not affected by this condition. See TSB 2030465, 91 MMI3G+ GPS navigation location inaccurate or navigation takes a very long time to acquire location (Q7 or Q3) for Q7 and Q3 vehicles.)
Supersedes Technical Service Bulletin Group 91 number 10-68 dated October 26, 2010.
Read full bulletin
The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.
Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011.
Read full bulletin
During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.
Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012.
Read full bulletin
The Bluetooth telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.
The navigation map update database 8R0051884CJ cannot be activated using Software Version Management.
Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008.
Read full bulletin
Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
THIS TECHNICAL SERVICE BULLETIN EXPLAINS POSSIBLE CAUSES FOR THE REARVIEW CAMERA TO NOT DISPLAY AN IMAGE.
Steering
37 bulletinsThis bulletin provides information about vibrations and rotational steering vibrations.
This bulletin provides informaiotn regarding squeaking noises when steering or maneuvering.
This bulletin provides information about vibrations and rotational steering vibrations.
This bulletin provides information about the steering wheel alignment.
This bulletin provides information when there are vibrations and rotational steering wheel vibrations.
This bulletin provides information vibrations and rotational steering wheel vibrations.
This bulletin provides information vibrations and rotational steering wheel vibrations.
This bulletin provides information when there is noise while steering.
This bulletin provides information when there is noise while steering.
This bulletin provides information for when there is noise when steering.
This bulletin provides information if there is noise when steering the vehicle.
Steering wheel shimmy, vibration and/or oscillation
Steering wheel shimmy, vibration and/or oscillation
Steering wheel shimmy, vibration and/or oscillation
Squeaking noises when steering or maneuvering
Steering wheel leather damage, all vehicles
Steering wheel shimmy, vibration, and/or oscillation
Squeaking noises when steering or maneuvering
This bulletin provides information for when the steering column adjustment does not work.
Steering wheel shimmy, vibration and/or oscillation
This bulletin provides information for instances where the steering wheel leather is damaged.
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
This bulletin states that squeaking noises which may be more prevalent in wet weather during steering is normal and...
Read full bulletin
repair is not needed.
This bulletin provides instructions for when a vibration is felt in the floor, seat, footwell, pedals or steering wheel...
Read full bulletin
while driving at highway speeds from 55 - 80 mph.
This bulletin explains that the steering wheel may warm up while being held leading to the impression that he steering...
Read full bulletin
wheel isn't heating evenly.
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
This information bulletin provides an explanation for squeaking noises heard when the steering wheel is turned or...
Read full bulletin
maneuvered.
Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel.
This technical service bulletin informs the reader that damage to the appearance of the leather steering wheel caused by...
Read full bulletin
outside influence is not covered under warranty.
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
This bulletin contains instructions for when the vehicle pulls to one side or the steering wheel is crooked.
Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013.
Read full bulletin
Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.
Supersedes Technical Service Bulletin Group 44 number 13-39 dated July 12, 2013.
Read full bulletin
Vehicle pulls (left or right). Steering wheel is not level or is off-center. These conditions may be noticed during PDI. If the condition is due to outside influence (such as an accident), this TSB does not apply. In an effort to gain information on this condition, Audi of America is asking you to contact the Audi Technical Assistance Center (TAC) before you perform any repairs.
Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012.
Read full bulletin
Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.
Software & Calibration
37 bulletinsThis is a notice for software changes with the ODIS diagnostic program to correct the communication during vehicle...
Read full bulletin
programming function: A software fix is needed to correct the issue: The ODIS Audi Brand update 2.41.1 is setting a ODS5003E error code when you perform the 90TV SVM flash.
This bulletin provides information on how to set up and use the FMC for obtaining vehicle software updates (SD Creator...
Read full bulletin
decomissioned).
This bulletin provides information for when the lane change assist radars cannot be calibrated after replacement.
Technical bulletins and updates
Technical bulletins and updates
Technical bulletins and updates
Technical bulletins and updates
Technical bulletins and updates
Technical bulletins and updates
Technical bulletins and updates
ElsaPro Software update and technical bulletins
Technical bulletins and updates
Updates and suggestions
Technical bulletins and updates
Technical bulletins and updates
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM)...
Read full bulletin
software update for any TSB or Update.
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM)...
Read full bulletin
software update for any TSB or Update.
This bulletin contains general instructions for software updates.
Dealer Communication - Vehicle Sales Reporting, Reinstatement, and Audit Policy Update - Effective September 30, 2021
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
00 Software Version Management (SVM), operating instructions
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
This bulletin contains a software update to address occasional stalling or running erratically without a DTC.
Read full bulletin
Occasional "System too rich" entries.
This bulletin contains a software update to address occasional stalling or running erratically without a DTC.
Read full bulletin
Occasional "System too rich" entries.
This bulletin contains a software update to address occasional stalling or running erratically without a DTC.
Read full bulletin
Occasional "System too rich" entries.
This bulletin contains a software update to correct a hesitation after deceleration at lower speeds.
This technical bulletin provides software instructions for vehicle vibration between 1000 rpm and 3000 with two DTCs.
This bulletin contains a software update to address occasional stalling or running erratically without a DTC.
Read full bulletin
Occasional "System too rich" entries.
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
This bulletin contains a software update to address occasional stalling or running erratically without a DTC.
Read full bulletin
Occasional "System too rich" entries.
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012.
Read full bulletin
This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
This technical service bulletin provides a software code for correcting an issue that causes DTC P046100.
Tires & Wheels
31 bulletinsThis TSB provides information regarding rotational and other steerihng wheel vibrations.
This bulletin provides information when noises from wheel input shaft/drive shaft are reported.
This bulletin provides information regarding wheel alignment.
This bulletin provides service information pertaining to noises from wheel input shaft/drive shaft.
Alignment - Repair Authorization
Tightening wheel bolts
Alignment - Repair Authorization
Tightening wheel bolts
Audi Normal Load Condition Tire Pressure Table
Audi Tire Chain Information by Vehicle -- MY 2014
Audi Tire Chain Information by Vehicle -- MY 2014
Audi Tire Chain Information by Vehicle -- MY 2014
Tire Pressure Table.
Tire Pressure Table.
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
2014 Audi Normal Load Condition Tire Pressure Table.
This informational bulletin explains how the temporary/collapsible spare wheel inflates.
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
Read full bulletin
2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and 2018-2020 RS5 Cabriolet, 2018-2020 S5 Sportback, 2008 A7, 2008-2011 S7
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
This bulletin provides information regarding vibrations or movement that are felt in the wheel.
This information TSB provides information regarding the correct way to torque adjust a wheel bolt.
This document contians the Audi tire chain information for all MY 2014 vehicles.
This document contains the Audi normal load condition tire pressure table.
This document contains the Audi normal load condition tire pressure table.
This document contains the Audi normal load condition tire pressure table.
This document contains the Audi normal load condition tire pressure table.
Read full bulletin
This document is in Spanish.
Supersedes Technical Service Bulletin Group 44 number 12-32 dated August 2, 2012.
Read full bulletin
Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.
Lighting
27 bulletinsThis TSB provides informatin when the cigarette lighter element does not eject, or the cigarette lighter is inoperable.
This bulletin provides informationw hen there are optical concerns with the tail lights.
This bulletin provides informationw hen there are optical concerns with the tail lights.
This bulletin provides information on visual concerns with the headlight lens.
This bulletin provides information for when the MIL/EPC light is illuminated, DTC P042000 or P043000, Catalyst system,...
Read full bulletin
bank 1 or 2 efficiency below thresh hold.
This bulletin provides information pertaining to when there are foreign objects inside of a headlight or taillight.
2014 Scheduled Maintenance Intervals\
This bulletin provides detailed information on the proper documentation of optical concerns for headlights and...
Read full bulletin
taillights.
This bulletin provides details on how to properly document optical concerns in headlights and taillights for warranty...
Read full bulletin
submissions.
When oil is drained through the drain plug, the oil might spill on components around the oil pan area.
Read full bulletin
If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
When oil is drained through the drain plug, the oil might spill on components around the oil pan area.
Read full bulletin
If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
This informational bulletin contains information on the different shading of LED headlights.
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
Exterior lights, moisture accumulation 2013-2021 A3 Cabriolet, 2016-2018 Sportback, 2004-2005 A4 Cabriolet, 2004-2008...
Read full bulletin
S4 Cabriolet, 2008 RS4 Cabriolet, 2010-2021 A4 allroad, 2018-2021 A5 Sportback, 2010-2012, 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2004-2006 A7, 2004-2011 S7, 2021 RS6 Avant, 2004-2006 S8
This informational bulletin contains instructions for when car wash bristles are stuck in the headlights.
Read full bulletin
2015-2021 A3 Cabriolet, 2015-2018 A3 e-tron, 2011-2021 A4 allroad, 2018-2021 A5 Sportback, 2011-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS6 Avant
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
Read full bulletin
2015-2021 A3 Cabriolet, 2016-2018 A3 Sportback, 2018-2021 A5 Sportback, 2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS 6 Avant
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
This special notice is to inform dealers to return all tail lamps with the part number listed that are below generation...
Read full bulletin
14s.
Supersedes Technical Service Bulletin Group 00 number 12-34 dated June 6, 2012.
Read full bulletin
The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.
This document contains the scheduled maintenance intervals.
Read full bulletin
The first scheduled service is due at 5,000 miles (8,000 km) or 1 year after delivery, whichever occurs first. Thereafter, all remaining scheduled services are due every 10,000 miles or 1 year after previous service, whichever occurs first.
Audi is committed to enhancing the Initial Quality Experience for our Customers within the first days of vehicle ownership.
Read full bulletin
We want to resolve any knowledge or technical concerns a customer may have about a new vehicle, and build a strong, positive, enduring relationship between dealer and customer. To support this commitment to both our dealers and our customers, Audi is introducing the Audi Second Delivery Program for MY2013 and MY2014 vehicles. The Program is applicable to all new MY2013 and MY2014 vehicles and includes a one-time reimbursement per VIN of $75. The Second Delivery may be performed at the dealership or a location of the customer?s choosing.
This document contains the scheduled maintence intervals.
Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010.
Read full bulletin
Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.
This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
Fuel System
26 bulletinsThis bulletin provides information when there is corrosion on the exhaust tail pipes.
This bulletin provides information when there are functional restrictions or driving behavior due to diesel detected in...
Read full bulletin
petrol.
This bulletin provides service information ror when the fuel tank cannot be fully filled.
This bulletin provides information when there are functional restrictions or driving behavior due to diesel detected in...
Read full bulletin
petrol.
This bulletin provides service information ror when the fuel tank cannot be fully filled.
Due to a software error, affected vehicles may experience elevated tailpipe emissions when driven in Sport Mode.
Read full bulletin
Additionally, under certain conditions, affected vehicles may also store non-erasable, On-Board Diagnostic fault code(s) that cannot be cleared following specific repairs. If this happens, the vehicle may not pass a state emissions inspection.
Due to a software error, affected vehicles may experience elevated tailpipe emissions when driven in Sport Mode.
Read full bulletin
Additionally, under certain conditions, affected vehicles may also store non-erasable, On-Board Diagnostic fault code(s) that cannot be cleared following specific repairs. If this happens, the vehicle may not pass a state emissions inspection.
Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the...
Read full bulletin
State of Minnesota.
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in one or more...
Read full bulletin
conditions.
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis.
Read full bulletin
Media files can now be viewed on any smartphone or tablet.
The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in one or more...
Read full bulletin
conditions.
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis.
Read full bulletin
Media files can now be viewed on any smartphone or tablet.
The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in one or more...
Read full bulletin
conditions.
High quality media files (video and sound) are now integrated into technical service bulletins on a case-by-case basis.
Read full bulletin
Media files can now be viewed on any smartphone or tablet.
DTC P310B00 (DFCC 2638) can be caused by quantity deviations of the fuel pump.
DTC P310B00 (DFCC 2638) can be caused by quantity deviations of the fuel pump.
The informational bulletin explains why during COVID-19 there is winter-blend fuel during a warmer season and causing...
Read full bulletin
some issues.
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
This bulletin contains instructions for when to add gasoline additives for cleaning the injectors.
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations.
Read full bulletin
Removed California DMV Tie-in Requirements
3.0 TDI vehicles were equipped with undisclosed Auxiliary Emission Control Devices which are not permitted by emissions regulations.
Read full bulletin
Revised legal approved copy.
E-mail - 3.0L TDI Gen 2 Emissions Compliant Repair (ECR) Approval
This technical service bulletin provides instructions for determining which parts related to the fuel tank ventilation...
Read full bulletin
system should be replaced to solve an issue with fueling the vehicle or MIL on.
This technical service bulletin provides instructions for determining which parts related to the fuel tank ventilation...
Read full bulletin
system should be replaced to solve an issue with fueling the vehicle or MIL on.
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR DETERMINING WHICH PARTS RELATED TO THE FUEL TANK VENTILATION...
Read full bulletin
SYSTEM SHOULD BE REPLACED TO SOLVE AN ISSUE WITH FUELING THE VEHICLE OR MIL ON.
Pre-Delivery & Maintenance
25 bulletinsThis bulletin provides service infrmation for workshop mode with Audi connect vehicles.
This service information TSB describes a cosmetic issue after using a car wash.
Vehicle Concerns Before Recall Repair Available
Pending service solutions and bulletins
Product quality is Announcing a new innovation in technical service bulletins: portable, easy to access videos
This bulletin contains instructions for when the zirconium inserts found to be not firmly attached during service work.
SAFETY RECALLS, COMPLIANCE RECALLS and STOP SALES
This technical service bulletin provides troubleshooting information for the vehicle locking system.
Maintenance.
This technical service bulletin provides troubleshooting information for the vehicle locking system.
This informational contains instruction on how to document optical concerns for warranty claims.
Recall Reminder Part Labels
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
This bulletin contains instructions for vehicle inspection, protection removal, and detailing.
This technical service bulletin provides instructions for replacing the coolant thermostat with a new part number to...
Read full bulletin
resolve a stored DTC.
This technical service bulletin provides instructions for the lubricating rear spoiler drive unit.
This document contains the Audi pre-delivery checklist.
Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014.
Read full bulletin
Technician preparation when calling the Audi Technical Assistance Center (TAC).
Supersedes Technical Service Bulletin Group 70 number 08-39 dated December 4, 2008.
Read full bulletin
Leather upholstery is dirty or stained.
Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013.
Read full bulletin
Instructions for vehicle inspection, protection removal, and detailing.
This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for...
Read full bulletin
service.
This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for...
Read full bulletin
service.
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR THE LUBRICATING REAR SPOILER DRIVE UNIT.
THIS TECHNICAL SERVICE BULLETIN PROVIDES INSTRUCTIONS FOR THE LUBRICATING REAR SPOILER DRIVE UNIT.
THIS TECHNICAL SERVICE BULLETIN PROVIDES TROUBLESHOOTING ADVICE FOR DETERMINING WHY THE GPS LOCATION DOES NOT MATCH THE...
Read full bulletin
VEHICLE'S ACTUAL LOCATION.
Body & Paint
22 bulletinsThis TSB describes a corrosion issue due to outside influence and the prohibition of warranty in these cases.
This bulletin provides information when there is a paint issue on alloy wheels.
This bulletin provides information when there is a film/visible rings on the clear glass cover of the headlight when the...
Read full bulletin
dipped beam is switched on.
This bulletin provides information when tehre is a paint issue on alloy wheels.
This bulletin provides information when there is corrosion on the tailpipes.
This TSB provides information when the exterior rubber trim is spotted.
This bulletin provides informationw hen there are car was brush bristles trapped in the seam between the headlight and...
Read full bulletin
fender.
This bulletin provides information when the sunglass holder will not close or is stuck closed.
This bulletin provides information on how to set up and use the SD Creator for obtaining vehicle software updates via...
Read full bulletin
the Mirror Server.
This bulletin provides information for when exterior glass cleaning is needed.
This bulletin provides information for when car wash bristles become stuck in the body gap between the headlight and...
Read full bulletin
fender.
This bulletin describes the process to clean sticker residue from the windshield.
This bulletin provides instructions for when the exterior trim has spots.
This bulletin provides instructions for when faint images appear on the windshield from the production sticker, or an...
Read full bulletin
image of the suction cups used to install the windshield in production.
Sunglass holder will not close
This bulletin provides instructions on how to properly clean exterior glass.
This bulletin provides instructions on how to clean exterior glass.
This bulletin contains instructions for front and/or rear doors cannot be opened or closed in freezing weather.
This bulletin provides instructions on how to clean exterior glass.
The rear spoiler extends slowly or operates erratically.
Read full bulletin
An error light for the rear spoiler may be illuminated. The rear spoiler operation can be restricted due to corrosion in the spoiler drive unit. As a result, the rear spoiler becomes stiff and does not reach its end points. This may cause a rear spoiler error light to be illuminated.
Customer may report hearing a noise from the rear of the vehicle when it is driven over bumps.
Read full bulletin
The center mounting nut on the rear bumper cover might be loose, allowing the rear cover to move when the vehicle is driven over a rough surface. The play from the loose mount will cause a noise. Additional noise can be heard when the cover and tail lamp rub.
AUDI: SOME VEHICLES, WHILE DRIVING, WOULD RECEIVE FALSE WARNINGS LIGHTS OF DOOR MIRRORS, OF VEHICLES IN BLIND SPOT WHEN...
Read full bulletin
NO VEHICLE IS PRESENT, FROM SIDE ASSIST. SOFTWARE NEED TO BE UPDATED. MODEL 2014-15 A5, S5, RS 5, CABRIOLET. *PE
HVAC & Climate
20 bulletinsThis bulletin provides information on the GFF test plan required for AC compressor replacements regardless of the...
Read full bulletin
concern.
This bujlletin provides information regarding the GFF test plan required for A/C compressor replacements regardless of...
Read full bulletin
the concern.
This bulletin provides information regarding the GFF test plan required for A/C compressr replaements regardless of the...
Read full bulletin
concern.
This bulletin provides information when a GFF test plan required for A/C compressor replacements regardless of concern.
This bulletin provides information pertaining to the GFF test plan required for A/C compressore replacements, regardless...
Read full bulletin
of the concern.
This bulletin provides informatin for the GFF test plan that is requied for AC compressor replacements.
This bulletin provides information when the air conditioning is no longer operative; DTC 00457, 00256, 01592.
This bulletin provides information on the GFF test plan required when replacing the A/C compressor.
This bulletin provides instructions for when the customer advises that there is insufficient or uneven cabin heating...
Read full bulletin
from the HVAC system.
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
This informational bulletin details on how to get a GFF test plan for A/C compressor replacements.
This bulletin contains repair instructions for when there is radio static when the rear heater is active.
This bulletin contains instructions for addressing an insufficient or uneven heating performance from the HVAC system.
This bulletin applies to any repair that requires replacement of the air conditioning compressor and details how to run...
Read full bulletin
a ODIS GFF test plan.
Supersedes Technical Service Bulletin Group 91 number 15-90 dated June 5, 2015.
Read full bulletin
When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue resolves itself intermittently. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. (To view the number of satellites being received, go to Nav >> Route >> Select Current Position (first item in list) and scroll up). No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). (Q7 and Q3 vehicles are not affected by this condition. See TSB 2030465, 91 MMI3G+ GPS navigation location inaccurate or navigation takes a very long time to acquire location (Q7 or Q3) for Q7 and Q3 vehicles.)
Customer may report poor performance of A/C system or that the A/C system is inoperative.
Read full bulletin
Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.
The A/C Compressor has been diagnosed as faulty and will be replaced under warranty.
Read full bulletin
When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.
Supersedes Technical Service Bulletin Group 91 number 15-87 dated May 18, 2015.
Read full bulletin
When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. (To view the number of satellites being received, go to Nav >> Route >> Select Current Position (first item in list) and scroll up. No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). Q7 and Q3 vehicles are not affected by this condition. The failure can happen at start-up or while the vehicle is being driven. The issue typically starts when the vehicle is driven on curvy or circular roads, driven in circles (such as when driven around a parking lot), or driven on or off an expressway.
Supersedes Technical Service Bulletin Group 87 number 15-63 dated May 18, 2015.
Read full bulletin
There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.
When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match...
Read full bulletin
the vehicle's actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. No DTCs related to the GPS antenna or MMI system are present. If the sky view is blocked because the vehicle is in a parking structure, below ground, or next to large buildings, it is normal for the GPS location or vehicle direction indicated on the MMI navigation map to not match the vehicle's actual location or direction of travel. The blocked sky view prevents the vehicle from receiving satellites, and the system may be temporarily lost until four satellites can be received. This is a normal condition, and is not related to the condition described above. Replacing the MMI main unit will not change this behavior. A potential failure in the internal hardware of the MMI main unit can cause the GPS signal to be blocked, even if good reception is available. The failure can happen at start-up or while the vehicle is being driven. The issue typically starts when the vehicle is driven on curvy or circular roads, driven in circles (such as when driven around a parking lot), or driven on or off an expressway.
Transmission
14 bulletinsThis bulletin provides informaiton when the transmission warning message appears in the cluster; P074100 stored in the...
Read full bulletin
TCM.
This bulletin provides information when there are leaks from the transmission.
This bulletin provides information about replacing the clutch end cover.
This bulletin provides information about replacing the clutch end cover.
Rough gear changes both when accelerating and slowing down
Gearbox warning light
After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component.
Read full bulletin
This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
Incorrect driving mode sensor module.
Read full bulletin
The driver information system displays the message ?Gearbox malfunction: you can continue driving?.
This bulletin contains instructions for diagnosing transmission leaks and repairing them.
This bulletin contains repair instructions for when DTC P179E00 is stored and the mechantronic unit and/or gear sensor...
Read full bulletin
G676 are being replaced.
This technical service bulletin provides guidelines for diagnosing the clutch plate.
Supersedes Technical Service Bulletin Group 35 number 12-08 dated December 21, 2012.
Read full bulletin
The driver information system displays the message ?Gearbox malfunction: you can continue driving?. Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A).
Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012.
Read full bulletin
Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.
Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A).
Read full bulletin
The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Scenario 1 is that entries are logged individually or in combination, with P179E logged first (using DTC environmental data).The entries are DTC P179E (Drive position sensor electrical error), DTC P0700 with DFCC 20196 (Transmission control system malfunction), DTC P1758 with DFCC 8464 (Terminal 15 voltage supply open circuit), and DTC P060A with DFCC 8126, 8345 (Internal control module monitoring processor performance) In this scenario, if DTC P179E is not logged first, this TSB does not apply. Scenario 2 is that entries are logged individually or in combination. The order in which the DTCs are logged is not relevant. The entries are DTC P179E with DFCC 8050, 8051, 8052, 8053, 17595, 17596, 17597, 17598, 17602 (Drive position sensor electrical error), DTC P179F with DFCC 8054, 8055, 8056, 8057, 17599, 17600, 17601 (Drive position sensor malfunction), DTC P0716 with DFCC 8096, 8101, 18153, 20738 (Input turbine/speed sensor ?A? circ. range/performance), DTC P171F with DFCC 8097, 8102, 18154 (Transmission input speed (RPM) sensor 2 implausible signal), DTC P0715 with DFCC 8094, 8103, 18161 (Input turbine/speed sensor ?A? circuit.), DTC P2765 with DFCC 8095, 8104 (Input turbine/speed sensor ?B? circuit), DTC P0501 with DFCC 8098 (Vehicle speed sensor ?A? range/performance), and DTC P2159 with DFCC 8099 (Vehicle speed sensor ?B? range/performance). Fault codes and DFCC codes must match exactly for this TSB to apply. The DFCC is the 4-6 digit code that is typically listed before the fault code. Incorrect driving mode sensor module.
Suspension
8 bulletinsThis bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
This bulletin describes the proper procedure to address a clicking or clacking noise from the wheel bearing
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
This bulletin contains instructions for determining if bushings need to be replaced.
This bulletin contains repair instructions for when the tolerances of the opening spring in the thermostat are not...
Read full bulletin
enough.
This technical service bulletin provides instructions for correcting a clicking sound from the wheel bearing(s).
This bulletin contains repair instructions for when the tolerences of the opening spring in the thermostat are not...
Read full bulletin
enough.
Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013.
Read full bulletin
The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
Air Bags & Safety
6 bulletinsThis Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the...
Read full bulletin
airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
The National Highway Traffic Safety Administration (NHTSA) has issued an urgent warning regarding counterfeit...
Read full bulletin
replacement airbag inflators that are being installed in used vehicles.
This Reporting Obligation requires technicains to contact the Technical Assistance Center (TAC) in cases where the...
Read full bulletin
airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.
This bulletin advises on identifying when a foreign object has obstructed normal operation of the seat belt.
This bulletin contains instructions for additional reporting requirements for safety related inquiries...
Read full bulletin
(airbag/seatbelts, accidents, fire and overheat damage).
This bulletin contains instructions for additional reporting requirements for safety related inquiries...
Read full bulletin
(airbag/seatbelts, accidents, fire and overheat damage.
Hybrid & EV
2 bulletinsThis document provides clarity on the MY24 Audi Q5 Hybrid fault code with technical service bulletin release on Monday,...
Read full bulletin
June 24.
This document provides clarity on the MY24 Audi Q5 Hybrid fault code with technical service bulletin release on Monday,...
Read full bulletin
June 24.