2009 Audi Q5 TSBs

stored in the ECM P030000.

brakes.

interrupted when the following DTC? s are present in the engine control module:

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

a restriction.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

No other DTCs are stored. Technical Background DTC P0234 can be set inadvertently by the software application.

a restriction.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

that the oil level is not okay.

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

a restriction.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

No other DTCs are stored. Technical Background DTC P0234 can be set inadvertently by the software application.

a restriction.

that the oil level is not okay.

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

a restriction.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

No other DTCs are stored. Technical Background DTC P0234 can be set inadvertently by the software application.

a restriction.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

that the oil level is not okay.

The leak can be traced to the connection of the water pump and the hose leading to the heater core (Figure 1). The seal ring is not the cause of the leak.

available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

When changing the oil filter and installing the new filter seal(s) in the oil filter housing, special attention is required.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

sent Takata airbag recall reminder notices to approximately 565 Audi owners in the State of Puerto Rico on July 25, 2022.

sent Takata airbag recall reminder notices to approximately 2,616 Audi owners in the State of Georgia on June 22, 2022.

The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.

to approximately 12,349 Audi owners in the State of California on April 29, 2022.

Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).

The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. On vehicles with Audi advanced key, the vehicle cannot be locked by remote control after the engine has been switched off.The Park position of the gear shifter is sporadically not recognized, which causes the ignition key to not be cleared and prevents the vehicle from being locked.

Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. As a result, application of the brake and accelerator pedals at the same time (brake pedal with left foot and accelerator pedal with right foot) results in the following: ? Brake pedal function (normal at all times) overrides any throttle application. ? Diagnostic Trouble Codes (DTCs) will not be stored. ? When the brake pedal is applied while the accelerator is depressed, engine RPMs will return to idle speeds of 1400 RPMs after approximately two seconds. ? When the accelerator is applied while the brake pedal is depressed, the vehicle accelerates slower than usual (reduced engine torque).

When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.

?Extended Emissions Warranty? Limited Warranty Extension The Limited Warranty Extension is applicable to 3.0L TDI vehicles Generation 2.1 SUV with engine code CNRB.

of Highway Safety and Motor Vehicles, Audi will be sending Takata airbag recall reminder notices to approximately 10,000 Audi owners in the state of Florida on October 14, 2019. 2005 A4 Avant, S4 Avant, 2006 A4 Avant, A6 Avant, S4 Avant, 2007 A4 Avant, A6 Avant, S4 Avant, S4 Cabriolet, 2008 A4 Avant, A6 Avant, RS4 Cabriolet, S4 Avant, S4 Cabriolet, 2009 A6 Avant, 2010 A6 Avant, 2011 A6 Avant, 2016 TT Roadster, 2017 R8 Spyder, TT Roadster.

Audi will be sending Takata airbag recall reminder notices to approximately 2,877 Audi owners in the state of Wisconsin on July 8, 2019. (2005) A6 SEDAN, A4 SEDAN, A4 AVANT, S4 SEDAN, S4 AVANT, (2006) A3, A6 SEDAN, A6 AVANT, A4 SEDAN, A4 AVANT, S4 AVANT, S4 SEDAN (2007) A3, A4 Cabriolet, S4 Cabriolet, A6 SEDAN, A6 Avant, S6 SEDAN, A4 SEDAN, A4 Avant, S4 Sedan, S4 Avant, A4 Cabriolet, RS4 Sedan, S4 Cabriolet, (2008) A3, A4 Cabriolet, S4 Cabriolet, A6 Sedan, A6 Avant, S6 Sedan, A4 Sedan, A4 Avant, S4 Avant, S4 Sedan, A4 Cabriolet, RS4 Sedan, RS4 Cabriolet, S4 Cabriolet, (2009) A3, Audi Q5, A4 Cabriolet, S4 Cabriolet, A6 Sedan, A6 Avant, S6 Sedan, A4 Cabriolet, S4 Cabriolet (2010) Audi Q5, A3, A5 Cabriolet, A6 AVANT, A6, S5 Cabriolet, S6 (2011) Audi Q5, A3, A5 Cabriolet, A6 AVANT, S5 Cabriolet, S6 (2012) Audi Q5, A5 Cabriolet, S5 Cabriolet, A3 (2013) A3 (2016) TT COUPE, TT ROADSTER (2017) TT COUPE, TT ROADSTER, R8 COUPE, R8 SPYDER

recall reminder notices to approximately 15,000 Audi owners in the State of New York on May 23, 2019. This document also applies to the 2007-2008 S4 Cabriolet, 2005-2008 S4 Avant, 2005-2008 A4 Avant, 2006-2011 A6 Avant, 2016-2017 Roadster, 2017 R8 Spyder.

vehicle has 75mm hydro-bushings.

The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.

Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.

DTCs may be stored in the heating and air conditioning electronics control module (address word 08). Improper operation of the fresh air blower could be caused by a faulty printed circuit board in the fresh air blower control module and/or the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower.

The customer complains that rattling or engine noise can be heard in the passenger compartment. The plastic sleeve of the intermediate steering shaft can slip towards the universal joint (mounting of the power steering rack), causing rattling or engine noise that can be heard in the passenger compartment.

A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. High ambient temperatures at the hydraulic guide links cause the noise.

Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. There are DTC entries present in the system (either static or sporadic). DTCs with description ?Brake control module - no signal/communication? are present in several control units. DTCs are stored in the ABS control module. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.

MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

DTCs may be stored in the heating and air conditioning electronics control module. A faulty printed circuit board in the fresh air blower control module and/or the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower can cause Improper operation of the fresh air blower.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (address word 01), is storing one or more engine misfire fault codes. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.

All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.

A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. This bulletin applies only to vehicles equipped with 75mm hydro-bushings. This bulletin does not apply to vehicles equipped with 65mm bushings. High ambient temperatures at the hydraulic guide links cause the noise.

MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

cover cleaning of the engine cylinder head secondary air ports to remove carbon buildup under specific conditions to 10 years or 120,000 miles, whichever occurs first, from the vehicle's original in-service date for certain 2009-12 Model Year Audi vehicles with 3.2L engine, and certain 2009-2013 Model Year Audi vehicles with 3.0T engines. The vehicle's original in-service date is defined as the date the vehicle was delivered to either the original purchaser or the original lessee; or if the vehicle was first placed in service as a "demonstrator" or "company" car, on the date such vehicle was first placed in service. The warranty extension is fully transferable to subsequent owners. Audi has determined that under certain driving conditions, carbon buildup can occur in the engine cylinder head secondary airports. Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of the on-board diagnostic system. In some locales, an illuminated MIL could cause the vehicle to fail an IM emissions inspection, vehicle registration application could be denied. Audi will diagnose, and if necessary clean the engine cylinder head secondary air ports to remove the carbon buildup at no cost to the customer as long as the vehicle is within the time and mileage limits of the warranty extension. This warranty extension covers only the diagnosis and cleaning of the cylinder head secondary air ports to remove the carbon buildup. Reimbursement is applicable only to the repairs described in this Warranty Bulletin.

Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL. In some locales, an illuminated Malfunction Indicator Lamp could cause your vehicle to fail an IM emissions inspection, and your vehicle registration application could be denied. Please be aware that other conditions (unrelated to the issue described in this letter) may cause the MIL in your vehicle to illuminate. Customers should be prepared to cover all diagnosis and repair costs for these other, unrelated conditions.

Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

DTCs may be stored in the heating and air conditioning electronics control module (address word 08). Malfunctions of the fresh air blower could be caused by a faulty printed circuit board in the fresh air blower control module and the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower.

The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.

Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. DTC with description "Brake control unit, no signal/communication" is present in several control units. DTC entry in ABS Control unit, J104 (03). One or more may be present. This condition does not result in any drivability concerns. The steering system is fully connected. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.

In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 2.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions; for example: stop-and-go traffic with extended idle periods.

Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.

Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure Deviation).

Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module.

After the activation of the cam actuator to change to the other cam profile, the pin of the actuator is pushed back in by the cam. This is confirmed by a voltage impulse, which is registered by the engine control unit and confirms the operation. If this does not happen, or not at the right time, a DTC "implausible signal" is saved in ECM memory. Check the distance of the pin tip of the cam actuator for valve lift system to the camshaft when it is not operated with a gauge. The measurement of the tip to the basic camshaft circle outside of the groove must be taken. If this measurement is 0.9mm, the actuator 06E103697J must be installed. The actuator 06E103697J must only be used, if the measurement is 0.9mm or bigger.

Oil consumption measurement - Repair Authorization (CA). In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil.

Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens. Damp air settles on the inside of a cold lens, which creates condensation. The headlight circulation system allows air from the outside to flow through the headlights. This open waterprotected ventilation system (needed for pressure compensation) creates different climate zones in the headlight: very warm areas, where the lens is warmed up by the light, and relatively cool areas, where the lens is cooled own by the air flow. Considerable differences in humidity and temperature between the inside and the outside of the headlights, even while driving, can lead to condensation. This is especially true in cold and wet weather, but it can also happen after a car wash, after steam cleaning the engine or the front end, with overnight temperature changes, etc. This phenomenon is more visible on lenses made of clear glass than on lenses with patterns. The moisture does not affect the headlight function (light performance) and does not lead to corrosion or other damage to headlight parts.

To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4 F (2 C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.

A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. This bulletin applies only to vehicles equipped with 75mm hydro-bushings. This bulletin does not apply to vehicles equipped with 65mm bushings. High ambient temperatures at the hydraulic guide links cause the noise.

Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.

The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. On vehicles with Audi advanced key, the vehicle cannot be locked by remote control after the engine has been switched off. DTC 00230 may be sporadically stored in the vehicle authorization system control module. The Park position of the gear shifter is sporadically not recognized, which causes the ignition key to not be cleared and prevents the vehicle from being locked.

Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.

The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.

DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.

The MIL is on. There is a rough idle. DTCs are stored in the ECM. Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

MIL on. DTCs are stored in the engine control module (ECM). No leaks are found in the EVAP system. Software update needed.

The noise is noticed after the car has been driven for a while and is warmed-up, and when the temperature outside is warm. The condition can be duplicated if the brakes are applied while the car is driven over bumps. High ambient temperatures at the hydraulic guide links cause the noise.

During reset of the service reminder, the message ?AIR system - action required - observe test plan? appears on the ODIS tester. MIL is not illuminated. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. There are DTC entries present in the system (either static or sporadic). DTCs are stored in the ABS control module. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected.

The plastic sleeve of the intermediate steering shaft can slip towards the universal joint (mounting of the power steering rack), causing rattling or engine noise that can be heard in the passenger compartment. Improved production process.

Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

MIL on. DTC P0234 (Turbo/Super Charger Overboost Condition) is stored in the engine control module, J623 (address word 01). No other DTCs are stored. DTC P0234 can be set inadvertently by the software application. DTC P0234 can be set with an actual cause in combination with loss of engine power and low/uneven engine performance, based on charge pressure control.

The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.

Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.

MIL is not illuminated. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.

There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.

In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 2.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions.

This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).

Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

engine to 8 years/80,000 miles (whichever occurs first) from the vehicle's in-service date or 12 months/12,000 miles (whichever occurs first) from the date of a settlement Service Adjustment, whichever date occurs later. The limited warranty extension is fully transferable to subsequent owners. Eligible vehicles are identified in Elsa with the Warranty Extension Key U24 OC Ext-Info AWO Resource Ctr. Some customers have complained of excessive engine oil consumption. Conditions unrelated to engine oil consumption are not covered under this extension.

This occurs after the engine is started, the message "TPMS" appears briefly and then turns off. There are no DTCs stored.

AND THEN DISAPPEARS, IT DOES NOT INDICATE AN ISSUE WITH THE TPMS SYSTEM.

ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE

UNDER CERTAIN SPECIFIC CONDITIONS, 7 YEARS OR 70,000 MILES, WHICHEVER OCCURS FIRST, EMISSIONS CONTROL SYSTEMS WARRANTY, FOR TURBOCHARGER, HAS BEEN EXTENDED, DUE TO A MALFUNCTION. *PE

A WARRANTY EXTENSION HAS BEEN ISSUED FOR 10 YRS OR 120, 000 MILES, WHICHEVER OCCUR FIRST, ON EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL INJECTORS, UNDER SPECIFIC CONDITIONS. MODEL 2008-2011. *PE

STALLING, THAT CAUSES THE MALFUNCTION INDICATOR LAMP (MIL) ON. MODEL 2008-2015 A3, A4, ALLROAD, TT, A5, A5 CABRIOLET, Q5, A6. *PE

INFORMATION PROVIDED REGARDING WARRANTY EXTENSION ON CARBON BUILDUP REMOVAL, ENGINE CYLINDER HEAD SECONDARY AIR PORTS. MODELS 2009-2012. NO MODEL PROVIDED. *PE

ENGINE AREA AND SEAL RING IS NOT THE CAUSE. MODEL 2009-2013 A4, A5, Q5, A6. *PE

DTC P0299 IS STORED. *JS UPDATED 12/2/13. *PE

MOVE SHIFTER; ENGINE SWITCHED OFF BUT REMOTE CONTROL CAN NOT LOCK WITH ADVANCED KEY; PARK IS NOT RECOGNIZED ELECTRICALLY. *PE

A SEAL INSIDE THE COOLANT PUMP CAN WEAR OUT AND LEAK COOLANT. THIS ALSO CAUSED THE ENGINE LIGHT TO COME ON. *RM UPDATED ON 06/27/2011. *KB

*RM

1 MISFIRE DETECTED-CYL.12 MISFIRE DETECTED); ENGINE MAY HAVE REDUCED PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. *PE

1 MISFIRE DETECTED-CYL. 12 MISFIRE DETECTED); ENGINE MAY HAVE REDUCED PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. *PE

CRANKSHAFT POSITION-CAMSHAFT CORRELATION BANK 2 SENSOR A & B; A SLIGHT POWER REDUCTION MAY BE ASSOCIATED WITH THIS CONDITION. THIS CONDITION DOES NOT CAUSE STALLING. *PE

POSITION, CAMSHAFT POSITION CORRELATION BANK 1 SENSOR B; DTC P0018 CRANKSHAFT POSITION, CAMSHAFT POSITION CORRELATION BANK 2 SENSOR A; DTC P0019 CRANKSHAFT POSITION, CAMSHAFT POSITION CORRELATION BANK 2 SENSOR B. *PE

mode.

Assistnce Center (TAC).

(TAC).

(Ghost faults).

whining, or similar interference.

This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure Deviation).

restriction.

with standard diagnosis.

exist or it is inoperative/constant warning.

2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2008-2020 A6, 2008-2011 A6 Avant, 2008-2020 A7, 2008-2020 A8, 2008-2019 e-tron, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2008-2012 S4, 2008-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2008-2020 S6, 2008-2020 S7, 2008-2009 S8, 2018-2021 SQ5, 2008-2020 TT Coupe, 2008-2020 TT Roadster, 2012 TT/RS Coupe

numbers going forward.

change.

This is for all keys and there is no relevant DTCs stored.

forward.

exist or it is inoperative/constant warning.

This notice contains information for the accessories operations technical bulletin.

The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. The squeak noise may be coming from the rear seat armrest area, specifically from the contact surface between the armrest lock and the striker pin. Production solution improved 2/3 rear seatback frame torsion bar to pivot incorporating internal plastic guides. The striker pin has also been improved to reduce the contact surface with the lock.

The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. The squeak noise may be coming from the rear seat armrest area, specifically from the contact surface between the armrest lock and the striker pin. Improved 2/3 rear seatback frame torsion bar to pivot incorporating internal plastic guides. The striker pin has also been improved to reduce the contact surface with the lock.

MODEL 2009-2016 Q5. *PE

MODELS AUDI Q5, Q7, A4, A5, A5 CABRIOLET (2009-14), A5, S5 (2008-14), A8 (2010-14) AND A6 (2011-14). *PE

*PE

range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

become stuck in the rear part of the lock (S-contact position). The stuck slide is not allowed to return to the starting point (0-position).

verification steps to ensure that the vehicle is configured correctly. For additional information on known current draw issues, refer to the following TSBs: ? 2014127: 27 Battery dead or low after returning to the vehicle (2007 A6, A8, Q7) ? 2019143: 27 Battery discharged on some vehicles with Advanced Key (2005 - 2008 A6, Q7)

Customer reports that the side assist is providing warnings when no vehicles are present. The radar is reflected from the rear wheels back to the sensors, resulting in a false side assist warning.

the release and automatic delivery of the Audi Q5 Hybrid Minimum Required Tools (MRT) Shipment. Starting September 23, 2015, every Audi dealer will be shipped one AT-378 Audi Q5 Hybrid Special Tool Package, Freight F.O.B. Snap-On OEM and invoiced directly by the Audi Special Tools Program (Snap-On Business Solutions - SBS).

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.

disconnected or replaced.

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

The radar is reflected from the rear wheels back to the sensors, resulting in a false side assist warning.

The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". The lock command history is stored in the convenience system control module (J393).

Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), the screen freezes briefly. * After the ignition is switched on (shortly after the phone automatically reconnects with the vehicle). * After the phonebook has downloaded. * When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. The command "Call <Name from directory>" is a global MMI command that is available in the telephone menu and main menu screens. If either menu is displayed, the message can appear when the voice recognition button (push to talk) on the steering wheel is pressed.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the programmed Homelink buttons no longer functions. The LED on the Homelink button that is no longer functioning now flashes slowly, indicating that no programming is stored. The customer's transmitter operates at 295Mhz. No DTCs are stored in any control units. At the workshop, the Homelink system can be programmed to the workshop garage door successfully. No trouble is found. The garage door opener control module, J530, was designed with an operational frequency range in which the 295Mhz frequency works correctly during the initial programming of the system. Over time, the transmitting frequency can drift out of range (especially in warmer climates), causing the system to lose its programming.

Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. The error could be corrected by resetting it (see radio system owner's manual). Otherwise, contact your Audi dealer." "The CD-drive is damaged and was therefore deactivated." The CD drive cannot be selected in the Source list and is described as "damaged." After the ignition is cycled or a radio reset performed, the CD drive is fully operational. DTC 00468 (CD-ROM Drive -R92- Faulty) is stored in the radio (address word 56). The DTC will be sporadic if the ignition has been cycled or a radio reset performed and will automatically be cleared after 40 ignition cycles without a reoccurrence. Only vehicles with the CAN-based generation 3 radio (Concert (PR 8UQ) or Symphony (PR 8YN)) are affected.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

Vehicle doors cannot be locked or unlocked using Advanced key. Vehicle cannot be started using the Start-Stop button. In Access/Start Authorization Control Module J518 (address word 05), DTC 03283 (Driver's side Access/Start Authorization Antenna Short Circuit to Ground), DTC 03284 (Right Access/Start Authorization Antenna Short Circuit to Ground) or DTC 00183 (Interior Access/Start Authorization Antenna 1 -R138-) are stored. Vehicle keys function properly otherwise, operating the door locks via the remote control as well as starting the vehicle using the ignition switch.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

DTC 03703 (Rear lid -closed- sensor) may be stored in the comfort system central control module, J393 (address word 46).

The master key with remote control does not engage or stay in the ignition lock. On vehicles without Advanced Key, the remote keys are inoperable. Keyless unlocking/locking using the door handle and keyless opening of the trunk lid using the trunk handle are inoperable. The vehicle cannot be started with the Start/Stop button. The remote keys are inoperable. The message "ignition lock faulty" may appear in the instrument cluster driver information display. DTC 00166 (Access/Start Authorization Switch -E415- Incorrect Signal) may be stored in Comfort System Central Control Module J393 (address word 46). It is possible that objects have been inserted into the ignition lock, which causes the slide of the ignition lock to become stuck in the rear part of the lock (S-contact position). The stuck slide is not allowed to return to the starting point (0-position).

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the programmed Homelink buttons no longer function. The LED on the Homelink button that is no longer functioning now flashes slowly, indicating that no programming is stored. The customer?s transmitter operates at 295Mhz. At the workshop, the Homelink system can be programmed to the workshop garage door successfully. No trouble is found. No DTCs are stored in any control units. The garage door opener control module, J530, was designed with an operational frequency range in which the 295Mhz frequency works correctly during the initial programming of the system. Over time, the transmitting frequency can drift out of range (especially in warmer climates), causing the system to lose its programming.

Part or all of the daytime running lights do not work on vehicles with LED DRLs. For vehicles with halogen DRLs, please reference TSB 2017488, 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only.

One or more warning lights on in cluster. The DIS or other displays in cluster are blank. MMI does not function. Windows do not function. LED indicators in various buttons inside the vehicle do not light up. The voltage regulator on the alternator can sporadically fail causing the electrical system to experience too high of voltage. As a result, the affected vehicle electronic components go in to high voltage protection and deactivate sensitive displays and indicators to prevent electrical damage. When an over voltage condition occurs the vehicle electronics and alternator are protected, thus there is no need to replace the entire alternator assembly.

Complaints are reported by the customer regarding electrical features and functions in the vehicle. One or more warning lights on in cluster. The DIS or other displays in cluster are blank. MMI does not function. Windows do not function. LED indicators in various buttons inside the vehicle do not light up. The voltage regulator on the alternator can sporadically fail causing the electrical system to experience too high of voltage. As a result, the affected vehicle electronic components go in to high voltage protection and deactivate sensitive displays and indicators to prevent electrical damage. When an over voltage condition occurs the vehicle electronics and alternator are protected, thus there is no need to replace the entire alternator assembly.

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

False warning from lane change assistant (Audi side assist). The warning light in the side mirror(s) illuminate when nothing is in the monitored areas to the sides of the vehicle. No relevant DTC(s) are stored in the lane change assistance control module, J769 (address word 3C). Software issue.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).

This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.

The parking aid system does not work. DTCs may be logged in parking aid control unit for disruption/short circuit to ground. The wire harness for the parking aid system may have been damaged when the front license plate frame was installed.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure.The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged.

Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly.

When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

No DTCs are stored. The keyless remote was not used to unlock the vehicle. In order to minimize current draw after the ignition has been turned off, the electronics system of the vehicle goes into sleep mode. During this time, each module monitors the CAN bus more slowly than when the electronics system is awake. Because the system is being monitored more slowly, there is a delay in the waking of the central locking system. This delay causes a delay in the disabling of the anti-theft alarm system when the manual key is used. If the key is turned in less than a quarter of a second, the system can unlock the vehicle even though the anti-theft alarm has not been disabled.

After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. If the SVM code was not acquired through the GP bulletin in ETKA, follow the instructions in the Service section of this bulletin to update the control module.

The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared.

The xenon headlight on one side of the vehicle flickers or is inoperative. The condition may be intermittent or permanent. DTCs are stored in the electronic central electronics control module for the affected headlight. Only xenon bulbs manufactured by Philips are affected. The xenon bulb may have an internal leak at the crimp of the electrodes, and xenon gas can be released. Without an adequate amount of xenon gas, the bulb cannot establish a stable light arc. The xenon igniter control unit (ballast) repeatedly tries to establish an arc, which may cause a flickering of the headlight.

The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used to lock or unlock the vehicle mechanically, and the key remote buttons can be used to lock or unlock the vehicle electronically. DTCs may be stored in the access and start authorization control module.

The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.

The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.

The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.

DTCs are stored in the comfort system central control unit. The "ignition lock faulty" message can be triggered by many different DTC entries. Presence of the message does not indicate that the ignition switch is faulty; the message typically has a different root cause. Replacing the ignition switch before completing GFF test plans typically does not correct the condition.

After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model?s SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed.

The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).

The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

The light bulb warning light is displayed in the instrument cluster with the following message: "Vehicle lights: malfunction". DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly.

Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.

Part or all of the daytime running lights do not work on vehicles equipped with LED daytime running lights. For vehicles with halogen daytime running lights, refer to TSB 2017488: 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only.

SPECIFIC CONDITIONS) TO 15 YEARS OR 150,000 MILES, WHICHEVER OCCURS FIRST, FROM THE VEHICLE'S ORIGINAL IN-SERVICE DATE. THE VEHICLE'S IN-SERVICE DATE IS DEFINED AS THE DATE THE VEHICLE WAS DELIVERED TO EITHER THE ORIGINAL PURCHASER OR THE ORIGINAL LESSEE; OR IF THE VEHICLE WAS FIRST PLACED IN SERVICE AS A "DEMONSTRATOR" OR "COMPANY" CAR, ON THE DATE SUCH VEHICLE WAS FIRST PLACED IN SERVICE. THIS WARRANTY EXTENSION IS FULLY TRANSFERABLE TO SUBSEQUENT OWNERS.WARRANTY KEY: U27 AIRBAG CM EXT 15/150,000 US ONLY IS ASSIGNED IN ELSA TO IDENTIFY VEHICLE ELIGIBILITY.IN RARE CASES, A POWER SUPPLY COMPONENT IN THE AIRBAG CONTROL MODULE MAY CORRODE AND CAUSE THE MODULE TO FAIL, TURNING ON THE AIRBAG LIGHT IN THE INSTRUMENT PANEL. IF THE AIRBAG LIGHT IS ON DUE TO THIS ISSUE, SAFETY SYSTEMS SUCH AS SEAT BELT PRETENSIONS AND AIRBAGS MAY NOT DEPLOY IN THE EVENT OF A CRASH, INCREASING THE RISK OF OCCUPANT INJURY.

AND NO OTHER VEHICLES ARE PRESENT. MODEL 2009-17 Q5. *PE

ON VEHICLES WITHOUT ADVANCED KEY, THE REMOTE KEYS ARE INOPERABLE. ON VEHICLES WITH ADVANCED KEY, UNLOCKING/LOCKING USING THE DOOR HANDLE AND THE OPENING OF THE TRUNK LID WITH TRUNK HANDLE ARE INOPERABLE; VEHICLE CANNOT BE STARTED WITH START/STOP BUTTON; REMOTE KEYS ARE INOPERABLE. *PE

THERE ARE TWO POSSIBLE CAUSES-LED CIRCUIT BOARD; DRL CONTROL UNIT, LOCATED INSIDE THE HEADLIGHT ASSEMBLY. *PE

THE FUEL GAUGE DOES NOT SHOW FULL EVEN THOUGH THE TANK IS COMPLETELY FILLED. THIS MAY OCCUR AFTER THE VEHICLE HAS BEEN TRANSPORTED BY A VEHICLE TRANSPORT TRUCK. THE LOWERED READING IS TRIGGERED WHEN THE VEHICLES ARE LOADED ONTO VEHICLE TRANSPORT TRUCKS OR WHEN PARKING ON AN INCLINE. THE VEHICLE IS TILTED, CAUSING THE FUEL LEVEL SENSOR VALUE TO CHANGE WITHOUT THERE BEING A SPEED SIGNAL IN THE INSTRUMENT CLUSTER. AS A RESULT, THE INSTRUMENT CLUSTER PERCEIVES A REFUELING PROCESS. *PE

XENON ON ONE SIDE FLICKERS OR IS INOPERATIVE INTERMITTENTLY OR PERMANENTLY); XENON BULBS WERE MANUFACTURED BY PHILIPS; DTC 00979 (RIGHT LOW BEAM HEADLIGHT M31 ELECTRICAL FAULT IN CIRCUIT); DTC 00978 (LEFT LOW BEAM HEADLIGHT M29 ELECTRICAL FAULT IN CIRCUIT). *PE

REGULATION, FUEL PRESSURE OUTSIDE TOLERANCE); P129F OR P008B (LOW PRESSURE FUEL SYSTEM, PRESSURE TOO HIGH); P129F OR P008A (LOW PRESSURE FUEL SYSTEM, PRESSURE TOO LOW); P2540 (LOW PRESSURE FUEL SYSTEM, PRESSURE OUT OF RANGE; AND P0087 (RAIL FUEL PRESSURE SYSTEM, PRESSURE TOO LOW). *PE

SVM IS A PROCESS TO UPDATE THE PROGRAMMING IN FLASHABLE (RE-PROGRAMMABLE) CONTROL MODULES AND/OR TO DOCUMENT CHANGES IN SOFTWARE LEVELS IN AUDI VEHICLES. THIS SYSTEM USES THE VAS 5051B OR VAS 5052 DIAGNOSTIC TOOLS TO SEND VEHICLE SPECIFIC DATA TO THE SVM DATABASE, TO DOWNLOAD INSTRUCTIONS FROM THE SVM DATABASE, AND TO FLASH CONTROL UNITS FOR IDENTIFIED SOFTWARE UPDATES. *PE

ITS A PROCESS TO UPDATE THE PROGRAMMING IN FLASHABLE (REPROGRAMMABLE) CONTROL MODULES AND/OR TO DOCUMENT CHANGES IN SOFTWARE LEVELS IN ALL AUDI VEHICLES. *PE

slowly.

repair is not needed.

wheel isn't heating evenly.

authorization control unit, J393, must be updated due to a diagnostic software error that prevents the DTC from being cleared.

slowly.

outside influence is not covered under warranty. 2008-2020 A3, 2015-2020 A3 Cabrio, 2005-2016 A3 Sportback, 2005-2020 A4, 2010-2020 A4 allroad, 2005-2012 A4 Avant, 2005-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2005-2020 A6, 2005-2011 A6 Avant, 2008-2020 A7, 2005-2020 A8, 2008-2019 e-tron, 2019-2020 e-tron quattro, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2007-2020 S6, 2008-2020 S7, 2007-2009 S8, 2018-2020 SQ5, 2004-2020 TT Coupe, 2004-2020 TT Roadster, 2012 TT/RS Coupe

Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

Steering wheel oscillation at highway speeds (typically between 70 and 85 mph). No vibration in the seat surface or other vehicle components. Audi original equipment tires are installed on the vehicle. If necessary, TSB 2022179 has been completed and the 1st harmonic of radial force of every tire and wheel assembly is below 18 lbs. at a tire pressure of 36 PSI (2.5 bar). Ride disturbances such as uneven roads, wheel imbalance, impermissibly high radial forces of the tires, or other rotating components on the front of the vehicle are transmitted to the steering wheel as a vibration or oscillation.

slowly.

slowly.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.

Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.

Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned.

Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned.

duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.

The customer may say that the noise is coming from the steering column area, and may describe the sound as buzzing, humming, whistling, whining, grinding, howling, and/or droning. The best way to understand the complaint is to discuss it with the customer. Faulty wheel bearing(s) may cause the noise.

The customer states that the steering feels stiff during turning. The condition occurs when the vehicle is stationary. The steering shaft needs to be updated.

Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.

Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.

DTC is present in the access start authorization control unit, J393 (address word 05), and cannot be cleared. The original electronic steering column lock control unit, J764, is installed. The original control unit has never been replaced. A replacement electronic steering column lock control unit, J764, has been installed. Before a replacement electronic steering column lock control unit, J764, is installed, the software of the access start authorization control unit, J393, must be updated due to a diagnostic software error that prevents the DTC from being cleared.

The condition occurs when the vehicle is stationary. The steering shaft needs to be updated.

Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.

Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.

The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead.

Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

INTERMEDIATE STEERING SHAFT NEEDS TO BE IMPROVED. MODEL 2008-2014 A4, A5, Q5. *PE

WITH IMPROVED INTERMEDIATE STEERING SHAFT. MODEL 2009-2014 A4, A5, A5 CAB, Q5. *PE

WHILE DRIVING ON UNEVEN ROADS OR WHEN TURNINGTHE STEERING WHEEL OVER THE FULL RANGE, CRACKING NOISES CAN BE HEARD COMING FROM THE FRONT AXLE. THE NOISE COMES FROM THE SUPPORT BRACKET FOR THE TOP OF THE FRONT STRUT. *PE

symbol or emoticon is used in the name field for contact(s).

See owner's manual" is displayed in the instrument cluster without DTCs.

This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.

following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.

navigation.

The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.

The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.

The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.

No audio from all audio sources (for vehicles with base sound system) or no audio from AM, FM, and satellite radio (for vehicles with Bose or Bang & Olufsen sound system). This TSB does not apply to vehicles with a separate amplifier and the complaint "no audio from all audio sources." Bluetooth is inoperative or loses connection. Bluetooth phone does not download contacts and/or call stacks. Satellite radio band is not available in band selection screen. Satellite radio presets sporadically disappear. When starting the 3G MMI system, the start screen does not appear and only the time is shown. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). The applicable vehicles can be clearly identified by the controller located in the center console. Continual improvements to MMI software provides solutions to issues experienced in the field.

appear in the contact on the customer"s cellular phone. These telephone numbers are displayed incorrectly on the radio display. The software incorrectly stores the downloaded phone numbers.

The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.

The Bluetooth telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.

If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system.

The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.

The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.

The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.

Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.

On generation III Concert and Symphony radios , the control knob or volume knob is broken or loose. Knobs may be damaged by outside influence.

Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.

The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle.

During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.

The Bluetooth telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.

The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off. The guidelines used for parking are fuzzy, distorted, or pixelated when compared with the guidelines displayed on another vehicle?s MMI.

The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.

Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".

THERE IS NO FAILURE. ALSO INCLUDED MODEL A4 MY 2014, MODEL A5 CABRIOLET MY 2014, MODEL Q5 MY 2014, MODEL S7 MY 2012-2014, MODEL RS7 MY 2014. *JS

MODELS A4, AUDI Q5 (2009-12), A5 (2008-12) AND A5 CABRIOLET (2010-12). *PE

(NO SOUND, INTERFERENCE, NAVIGATION NOT WORKING, BLACK SCREEN, ETC.) MAY OCCUR ON AUDI VEHICLES WITH THE THIRD VERSION OF MULTIMEDIA INTERFACE (MMI 3G) MANUFACTURED WITHIN A LIMITED PERIOD. REAR SIDE PARKING LIGHT BULB IS INOPERATIVE ON EITHER LEFT OR RIGHT SIDE. MIL ON. *PE

2,907 Audi owners in the State of Massachusetts on March 13, 2023.

Audi owners in the State of New Mexico on March 13, 2023.

Audi owners in the State of Colorado on February 13, 2023.

Audi owners in the State of New York on October 17, 2022.

notices to approximately 1,121 Audi owners in the state of South Carolina on September 19, 2022.

Audi owners in the State of Virginia on July 21, 2022.

approximately 939 Audi owners in the State of Alabama on March 23, 2022.

to approximately 4,943 Audi owners in the state of Pennsylvania on January 24, 2022.

notices to approximately 1,290 Audi owners in the state of South Carolina on January 24, 2022.

owners in the State of Idaho on August 30, 2021.

Audi owners in the State of New York on June 21, 2021.

Audi owners in the State of Texas on May 17, 2021.

approximately 3,000 Audi owners in the State of Michigan on August 10, 2020.

approximately 370 Audi owners in the State of Texas on July 28, 2020.

Audi owners in the State of Tennessee on July 7, 2020.

in the State of Florida on June 26, 2020.

45 Audi owners in the State of California on June 22, 2020.

Audi owners in the State of Nebraska on March 23, 2020.

owners in the State of Ohio on February 10, 2020.

Audi owners in the State of Georgia on January 24, 2020.

approximately 1,800 Audi owners in the state of South Carolina on January 20, 2020.

approximately 27,300 Audi owners in the state of California on January 14, 2020.

of Neighborhoods, Audi will be sending Takata airbag recall reminder notices to approximately 2,300 Audi owners in the state of Texas on November 4, 2019.

Audi owners in the state of Arkansas on November 19 2019.

owners in the State of Pennsylvania on November 18, 2019.

2005 A4 Avant, S4 Avant, 2006 A4 Avant, A6 Avant, S4 Avant, 2007 A4 Avant, A6 Avant, S4 Avant, S4 Cabriolet, 2008 A4 Avant, A6 Avant, RS4 Cabriolet, S4 Avant, S4 Cabriolet, 2009 A6 Avant, 2010 A6 Avant, 2011 A6 Avant, 2016 TT Roadster, 2017 R8 Spyder, TT Roadster.

Audi owners in the State of Minnesota on September 16, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3, 2016 TT Coupe, TT Roadster, 2017 R8 Coupe, R8 Spyder, TT Coupe, TT Roadster

Audi owners in the State of California on August 5, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3

4,500 Audi owners in the State of North Carolina on August 19, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3, 2016 TT Coupe, TT Roadster, 2017 R8 Coupe, R8 Spyder, TT Coupe, TT Roadster

Audi owners in the State of Virginia on August 12, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3, 2016 TT Coupe, TT Roadster, 2017 R8 Coupe, R8 Spyder, TT Coupe, TT Roadster

reminder notices to approximately 1,476 Audi owner in the state of Kentucky on July 15, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3, 2016 TT Coupe, TT Roadster, 2017 R8 Coupe, R8 Spyder, TT Coupe, TT Roadster

(airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe

replaced by final remedy parts. Over the coming weeks, you will see a decrease in the supply and allocations of these interim remedy inflators. Dealers scheduling repairs under this recall should take this into consideration and only schedule customer appointments according to available internal (interim remedy) parts inventory. Future communications will follow with additional details and actions your dealership will need to take as we move towards launching final remedy repairs.

After this date, Takata allocations will be based on the previous week?s paid claim volume. It is CRITICAL that claims are submitted in a timely fashion in order to receive an appropriate volume of additional parts to support demand.

for some vehicles to be at risk for containing counterfeit airbags if the airbags in the vehicle were replaced at independent repair shops that are not Audi dealerships or Audi certified. The Audi vehicles listed by NHTSA as at risk vehicles for the potential of containing counterfeit airbags if the airbags have been replaced are MY 2006-2009 A3, A4, A6, A8, Q5, and Q7 vehicles. If a Customer purchased their vehicle new, or if the vehicle is Certified pre-owned and a CARFAX report shows the airbag has never been replaced, there is no issue.

Portal.

AND HAVE NOT BEEN CERTIFIED BY DEALERSHIPS OR AUDI. MODELS 2006-2009 A3, A4, A6, A8, Q5, Q7. *PE

MODELS A4, S4, A5, S5, Q5, TT, TTS, A3, PA , C6, A6 PA, D4, A8,C7 A7. *PE

AFTER REPLACING THE AIRBAG CONTROL UNIT, THE CONTROL UNIT CANNOT BE CODED VIA SVM SPEC/ACTUAL. THE LATEST REVISION OF THE AIRBAG CONTROL UNIT MUST BE CODED AND PARAMETERIZED USING AN SVM CODE, WHICH IS LISTED ETKA IN THE REMARKS AREA FOR THE PART NUMBER. *PE

Avant, A4 Cabriolet, S4 Cabriolet, A5 Cabriolet, S5 Cabriolet, A6 Avant, A6 Sedan, Q5, R8 Coupe, R8 Spyder, RS4 Cabriolet, RS4 Sedan, S6 Sedan, S6 Sedan, TT Coupe, and TT Roadster vehicles

will resume scheduling part pick-up from dealerships and service centers.

This document also applies to the 2007-2008 S4 Cabriolet, 2005-2008 A4 Avant, 2005-2008 S4 Avant, 2006-2011 A6 Avant, 2008 RS4, 2016-2017 TT Roadster and 2017 R8 Spyder.

required" message.

This TSB contains information on technician preparation when calling the Audi Technical Assistance Center

Oil filter cartridge requires replacement.

VIN plate and/or B-Pillar Safety Certification label requires replacement.

MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage greater than 20,000 miles.

Customer may report squeak or rattle sounds coming from the rear seat area. The rattle sound can be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. The squeak noise may be coming from the rear seat armrest area, specifically from the contact surface between the armrest lock and the striker pin.

Customer may report the front of the passenger floor mat is wet after heavy rains. The flat surface of the fresh air intake may warp over time and cause a gap where it meets with the plenum wall. During heavy rains, water can back up and enter the vehicle through this gap.

Technician preparation when calling the Audi Technical Assistance Center (TAC).

A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.

Leather upholstery is dirty or stained.

Customer may report hearing squeak or rattle sounds coming from the rear seat area. The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. The squeak noise may be coming from the rear seat armrest area, specifically from the contact surface between the armrest lock and the striker pin.

Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options.

The rear center seat rattles at the backrest latching mechanism. The rear center seat release handle for folding the center seat backrest flat does not function. The rod between the rear center backrest latch and the release lever is detached. After the rod detaches and the center backrest is latched to the rear backrest on the driver?s side, the center backrest cannot be folded flat independent from the driver?s side rear backrest. The loose connection inside the latching mechanism can create noises from the rear center seat when the vehicle is driven over rough roads.

Customer may report hearing squeak or rattle sounds coming from the rear seat area. The rattle sound may be caused from the pivot point of the torsion bar within the 2/3 rear seat backrest pivot assembly. The squeak noise may be coming from the rear seat armrest area, specifically from the contact surface between the armrest lock and the striker pin.

The rear center seat rattles at the backrest latching mechanism. The rear center seat release handle for folding the center seat backrest flat does not function. The rod between the rear center backrest latch and the release lever is detached. After the rod detaches and the center backrest is latched to the rear backrest on the driver?s side, the center backrest cannot be folded flat independent from the driver?s side rear backrest. The loose connection inside the latching mechanism can create noises from the rear center seat when the vehicle is driven over rough roads.

service.

A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold (normally below freezing) and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.

REQUIRED" MESSAGE.

REQUIRED" MESSAGE.

APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM

APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM

APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM

APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN. *RM

UNDER CERTAIN CONDITIONS THE COOLANT PUMP MAY LEAK. *RM

(crawling when pulling away or briefly before standstill).

Customer may complain about brake squeak or squeal with light to moderate pedal pressure from front brakes.

temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.

headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.

Brakes on vehicles produced before September 3, 2012 (calendar week 36 of 2012), squeak or squeal when used with light to moderate force.

If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.

DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools.

Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.

Oil appears on one or several shock absorbers.

Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.

This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.

Oil appears on one or several shock absorbers. Oil may appear on a shock absorber. As a result of a leak because the shock absorber is damaged. As a result of residue from when the shock was filled during production, or of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.

Customer may complain about brakes squeak or squeal with light to moderate pedal pressure.

Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.

GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE

IGNITION KEY CANNOT BE REMOVED, AND OTHER VARIOUS ISSUES. MODEL 2009-2014 A4/S4, A5/S5, A5/S5 CAB, Q5. *PE UPDATED 05/21/2014 *JS

*JS

OPERATION, DUE TO PADDLE, OF REAR SILL TRIM, NOT CONTACTING OPPOSING LID LATCH POINTS, UNIFORMLY. MODELS 2007-2014 Q7, 2009-2014 Q5. *PE UPDATED 07/10/2013 *JS

ARE DAMAGED, PREVENTING PROPER ANALYSIS. *PE

with the remote.

with the remote.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

"Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch.

"Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch.

Air flows through the exterior rear view mirror housing at the seam where the turn signal lamp meets the housing. This causes a high-frequency whistling tone.

?Low Oil Level? message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch.

The customer may report hearing noises when operating the window or noises from inside the door when driving on rough roads. When the window is lowered, it collides with the clip that holds the window guide cable. This causes the clip to open and contact the window during operation, or to rattle when the vehicle is driven on rough roads.

The customer may report noises when operating the window or noises from inside the door when driving on rough roads. When lowering the window, it collides with the clip that holds the window guide cable. This causes the clip to open and contact the window during operation, or rattle while driving on rough roads.

When the roof carrier bars are installed on the vehicle the acoustic environment in the cabin is predictably affected. The intent of the roof carrier bars is solely for the transport of cargo. When installed an increase in wind noise should be expected.

The outer door seals have become partially detached. Loss of adhesion between the door structure and door seal due to a flaw in the attachment process in production.

The outer door seals have become partially detached. Loss of adhesion between the door structure and door seal due to a flaw in the attachment process in production.

The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the handle is slack. When fitting the Bowden cable from the mounting bar to the door lock, the cable can get kinked. In some cases, this can increase the inner friction of the strand in the Bowden cable. As a result, the door lock stays in pressed position or does not completely return to its zero position. When the Bowden cable gets twisted during the installation, the rubber grommets can get distorted. Consequently, the Bowden cable has a too-high inner friction and the door lock does not move to the zero position.

Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors. The added features include the turn signal lamp, side assist lamp, perimeter lamp, etc. As the complexity of the exterior rear view mirror increases, the mirrors become more susceptible to wind noise. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.

After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors. The added features include the turn signal lamp, side assist lamp, perimeter lamp, etc. As the complexity of the exterior rear view mirror increases, the mirrors become more susceptible to wind noise. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.

Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.

The customer may report hearing noises when operating the window or noises from inside the door when driving on rough roads. When the window is lowered, it collides with the clip that holds the window guide cable. This causes the clip to open and contact the window during operation, or to rattle when the vehicle is driven on rough roads.

The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available.

Wind noise is heard by the customer at highway speeds. Air flows through the exterior rear view mirror housing at the seam where the turn signal lamp meets the housing. This causes a high-frequency whistling tone.

The outer door seals have become partially detached. Loss of adhesion between the door structure and door seal due to a flaw in the attachment process in production.

The customer may report hearing wind noise while driving at highway speeds. The noise may occur on either side of the vehicle. Wind noise may be coming from either the mirror base or the lane change assist lamp. Improved parts are available.

Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. Throughout the development of the Audi Q5 and Audi Q7, various features have been added to the exterior rear view mirrors. The added features include the turn signal lamp, side assist lamp, perimeter lamp, etc. As the complexity of the exterior rear view mirror increases, the mirrors become more susceptible to wind noise. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.

Customer may report hearing wind noise from the front door area when the vehicle is driven at highway speeds. After diagnosis, it is determined that the source of the wind noise is the exterior rear view mirrors. The two main sources of wind noise from the exterior rear view mirrors are: the seam surrounding the turn signal lamp and the seam at the mirror base. The modifications explained in the Service section of this bulletin will effectively mitigate the wind noise symptom for the customer.

*PE

software update for any TSB or Update.

software update for any TSB or Update.

2016-2020 A3, 2016-2020 A3 Cabrio, 2016 A3 Sportback, 2016-2020 A4, 2016-2020 A4 allroad, 2016-2012 A4 Avant, 2016-2020 A5 Cabrio, 2016-2020 A5 Coupe, 2018-2020 A5 Sportback, 2016-2020 A6, 2016-2020 A7, 2016-2020 A8, 2016-2020 e-tron, 2019-2020 e-tron quattro, 2016-2020 Q3, 2016-2020 Q5, 2016-2020 Q7, 2016-2020 Q8, 2016-2020 R8 Coupe, 2016-2020 R8 Spyder, 2017-2019 RS3, 2016-2020 RS5, 2016-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2016-2020 S5 Cabrio, 2016-2020 S5 Coupe, 2018-2020 S5 Sportback, 2016-2020 S6, 2016-2020 S7, 2018-2021 SQ5, 2016-2020 TT Coupe, 2016-2020 TT Roadster

This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.

DETAILING THE GENERAL PROCESS FOR CARRYING OUT A SOFTWARE VERSION MANAGEMENT (SVM) SOFTWARE UPDATE FOR ANY TSB OR REQUIRED VEHICLE UPDATE (RVU). TROUBLESHOOTING INFORMATION IS INCLUDED. *PE

SOFTWARE FAULT. OPTIMIZED SOFTWARE. REPLACEMENT OF THE CONTROL UNIT IS NOT NECESSARY. WARRANTY CLAIMS FOR CONTROL UNIT REPLACEMENTS WITHOUT USE AND APPLICATION OF THIS TSB WILL BE DEBITED. *PE

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

01800, or B126AF0.

01800, or B126AF0.

14s.

The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. This is a deliberate design feature designed to avoid injuries in the event of a collision.

Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.

PERMANENT, DUE TO A POSSIBLE INTERNAL LEAKAGE AT CRIMP OF ELECTRODES AND GAS IS BEING RELEASED. MODEL 2008-2009 A4, A5, Q5. *PE

ALL DAYTIME RUNNING LIGHT (DRL) LEDS IN ONE HEADLIGHT ASSEMBLY ARE INOPERATIVE. REDESIGN OF DRL CONTROL UNIT ELECTRONICS. *PE

DAYTIME RUNNING LIGHTS DO NOT WORK ON VEHICLES WITH XENON HEADLIGHTS. THE THUMB WHEEL OR OPTION FOR DAYTIME RUNNING LIGHTS IS TURNED OFF BY MISTAKE. *PE

*PE

ONLY PHILIPS BRAND XENON BULBS ARE AFFECTED. *PE

ONLY PHILIPS BRAND XENON BULBS ARE AFFECTED. *PE

The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.

Clicking or clacking noise when maneuvering or parking. Normal driving dynamics may cause microscopic movements between the wheel bearing and wheel bearing housing.

The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.

A loud noise is heard when the outside mirrors are folded in or out. The noise originates in the metal spring inside the hinge area of the mirror housing. This spring is used for stabilizing the mirror when the vehicle is driven over rough roads to minimize mirror glass shake. When the mirror housing is folded in or out, the spring must turn or twist with the movement of the housing. The bottom and the top of the spring sit on a plastic base and due to increased friction at these contact points, the spring will skip along the plastic base during the folding operation and creates the noise. The normal functionality of the mirror is not affected.

*PE

State of Minnesota.

conditions.

Media files can now be viewed on any smartphone or tablet.

conditions.

Media files can now be viewed on any smartphone or tablet.

conditions.

Media files can now be viewed on any smartphone or tablet.

Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.

The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.

Moisture in the driver or front passenger foot well. Due to a faulty and / or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose.

Moisture in the driver or front passenger foot well. Due to a faulty and/or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose.

UNDER SPECIFIC CONDITIONS, THE EMISSIONS CONTROL SYSTEMS WARRANTY, FOR FUEL INJECTOR REPLACEMENT, HAS BEEN EXTENDED TO 10 YRS OR 120,000 MILES, WHICHEVER HAPPENS FIRST. MODEL 2009-2011. *PE

FRONT FOOT WELL AREA DUE FAULTY AND INCORRECT INSTALLATION OF CONDENSATION DRAIN HOSE. MODELS 2008-2013 A4, A5, A5 CABRIOLET, Q5. *PE

HOSE THAT ASSEMBLED BY SUPPLIER INCORRECTLY. MODELS A4, A5 COUPE, Q5 AND A5 CABRIOLET. MY 2009-2011. *PE

*RM

THE FUEL GAUGE DOES NOT SHOW FULL EVEN THOUGH THE TANK IS COMPLETELY FILLED. THIS MAY OCCUR AFTER THE VEHICLE HAS BEEN TRANSPORTED BY A VEHICLE TRANSPORT TRUCK. *PE

The seal ring is not the cause of the leak.

The seal ring is not the cause of the leak.

The seal ring is not the cause of the leak.

The seal ring is not the cause of the leak.

The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.

When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.

Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.

There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.

Wheel bolt requires torque adjustment.

Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.

This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.

The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.

Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.

The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle.

ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. MODELS 2004-14, A3, TT, Q7, A4, A5, A6, A7, A8, Q5, S4, S5, S6, S7, RS5. *PE

CERTAIN MODELS, CAMERA IMAGE CAN BE RE=ACTIVATED. MODEL YEARS 2008-2013. *PE

*PE