2013 Audi A8 TSBs

the height to which the vehicle has been flooded.

tester refers to this reportin gobligation or to TPI 2033392.

not activate.

mode.

not activate.

vehicle models.

Assistnce Center (TAC).

(TAC).

(Ghost faults).

whining, or similar interference.

No DTCs are stored.

level is correct.

The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

system.

restriction.

exist or it is inoperative/constant warning.

restriction.

expansion tank cap.

it from occurring again.

exist or it is inoperative/constant warning.

toothed belt.

exist or it is inoperative/constant warning.

restriction.

restriction.

restriction.

restriction.

restriction.

exist or it is inoperative/constant warning.

Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.

2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 Q7, 2019 Q8, 2000-2019 TT, 2008-2018 R8

restriction.

2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster

2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2008-2020 A6, 2008-2011 A6 Avant, 2008-2020 A7, 2008-2020 A8, 2008-2019 e-tron, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2008-2012 S4, 2008-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2008-2020 S6, 2008-2020 S7, 2008-2009 S8, 2018-2021 SQ5, 2008-2020 TT Coupe, 2008-2020 TT Roadster, 2012 TT/RS Coupe

contaminated.

restriction.

contaminated.

contaminated.

restriction.

contaminated.

numbers going forward.

restriction.

restriction.

contaminated.

on demand function.

reception.

The compartment was bumped or kicked while open, causing it to disengage.

The pin from the locking pawl is out of place.

change.

This is for all keys and there is no relevant DTCs stored.

exist or it is inoperative/constant warning.

expansion tank cap.

This notice contains information for the accessories operations technical bulletin.

This document is in Spanish.

They are designed to help educate you and make an impact on customer satisfaction. Dealer Communications dealing with IQS topics are also distributed on occasion.

Replace the coolant expansion tank produced within a certain time frame.

vehicles with 0BK & 0BL Gearbox.

stored in the ECM P030000.

brakes.

working; mileage below 50 km/32 miles.

working; mileage below 50 km/32 miles.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. In such a situation, the fuel metering valve is deactivated and the high-pressure fuel pump switches to full supply mode. Because the increased rail pressure does not match the respective driving situation, the DTC appears.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair.

that the oil level is not okay.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

-Electronic Parking Brake (EPB) activates when driver?s door is opened (A6/A7/S6/S7 only)

that the oil level is not okay.

-Electronic Parking Brake (EPB) activates when driver?s door is opened (A6/A7/S6/S7 only) -00 software version management for all audi 2002 and on

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. In such a situation, the fuel metering valve is deactivated and the high-pressure fuel pump switches to full supply mode. Because the increased rail pressure does not match the respective driving situation, the DTC appears.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair.

that the oil level is not okay.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

-Electronic Parking Brake (EPB) activates when driver?s door is opened (A6/A7/S6/S7 only)

that the oil level is not okay.

-Electronic Parking Brake (EPB) activates when driver?s door is opened (A6/A7/S6/S7 only) -00 software version management for all audi 2002 and on

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

If there is a low system voltage, the on/off ratio may not be enough to keep the fuel metering valve constant in all areas. In such a situation, the fuel metering valve is deactivated and the high-pressure fuel pump switches to full supply mode. Because the increased rail pressure does not match the respective driving situation, the DTC appears.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

fuel delivery, exhaust after-treatment (SCR/AdBlue and emissions) systems, or transmission, a Repair Authorization is necessary prior to repair.

that the oil level is not okay.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

-Electronic Parking Brake (EPB) activates when driver?s door is opened (A6/A7/S6/S7 only)

that the oil level is not okay.

-Electronic Parking Brake (EPB) activates when driver?s door is opened (A6/A7/S6/S7 only) -00 software version management for all audi 2002 and on

Blow-by gases from the crankcase breather discolor the pipe (Figure 1). This is a normal condition.

The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

Updated engine control module (ECM) software.

High temperatures cause the coolant to become encrusted on the connection flange of the turbocharger (Figure 1).

available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures.

consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan.

The adaption must be reset after the engine is installed.

Particles in the cooling system from the production process affect the closing of the coolant thermostat.

Customer may report feeling a slight hesitation or delay at 5-9 mph after accelerating from a stop.

Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).

Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. As a result, application of the brake and accelerator pedals at the same time (brake pedal with left foot and accelerator pedal with right foot) results in the following: ? Brake pedal function (normal at all times) overrides any throttle application. ? Diagnostic Trouble Codes (DTCs) will not be stored. ? When the brake pedal is applied while the accelerator is depressed, engine RPMs will return to idle speeds of 1400 RPMs after approximately two seconds. ? When the accelerator is applied while the brake pedal is depressed, the vehicle accelerates slower than usual (reduced engine torque).

done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off.

done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off.

done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off.

noises when accelerating and/or there is reduced engine performance.

noises when accelerating and/or there is reduced engine performance.

noises when accelerating and/or there is reduced engine performance.

noises when accelerating and/or there is reduced engine performance.

TDI ONLY

noises when accelerating and/or there is reduced engine performance.

noises when accelerating and/or there is reduced engine performance.

4,000rpm, and there are DTCs about the intake manifold flap adjustment.

on the circumstances under which DTC P244000 and/or P244200 were stored.

A metallic whistling or grinding sound is heard from the engine compartment when the vehicle is at idle speed. The sound usually only occurs when the engine is warm. The MIL is sporadically on. DTCs are stored in the ECM. A leak in the crankcase breather module (pressure regulating valve) can cause this condition.

on the circumstances under which DTC P244000 and/or P244200 were stored.

Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.

DTCs are stored in the ECM. On the camshaft adjustment valve, the filter element can loosen. There is no consequential damage from loosened particles in the oil circuit. They are gathered by the oil filter.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM). The diagnostic limitations were too narrow.

This can result in leaks between the coolant lines and the turbocharger.

Audi advanced key (keyless entry) is inoperative on all doors, but the engine can be started with the keyless starting system (keyless go). The keyless starting system (keyless go) is a standard feature; Audi advanced key is an optional feature. All vehicles have an engine start-stop button (-E408-) and touch sensor surface on the outer door handles, but this does not mean that the optional Audi advanced key function is installed.

The MIL is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults may be stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss as a result of coolant migration in the electrical harness, faults in 08-Heating and Air Conditioning Electronics that result from coolant migration in the electrical harness, or a faulty N82 control valve.

to correct a concern about the engine running irregularly.

If this happens, the heating output of the air conditioner will be reduced.

4,000rpm, and there are DTCs about the intake manifold flap adjustment.

4,000rpm, and there are DTCs about the intake manifold flap adjustment.

This can result in leaks between the coolant lines and the turbocharger.

This can result in leaks between the coolant lines and the turbocharger.

This can result in leaks between the coolant lines and the turbocharger.

DTCs are stored in the subframe mount control module. The basic settings of the active engine mounts in the subframe mount control module, J931, are deactivated when work is done on either of the vehicle electrical system control modules, J519 and/or J520 (for example, when a key is programmed). As a result, the vehicle vibrates or judders when cylinders are actively switched off.

There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.

DTCs are stored in the engine control module (ECM) . In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module (TCM). There is an issue with the ECM and/or TCM software.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.

On 4.0l bi-turbo FSI engines, the pipe on the impeller side of the bank 2 turbocharger looks discolored when compared to the pipe on the bank 1 turbocharger.

MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.

the pipe on the bank 1 turbocharger. The crankcase breather is only connected to the bank 2 turbocharger inlet. Blow-by gases from the crankcase breather discolor the pipe. This is a normal condition.

Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.

cover cleaning of the engine cylinder head secondary air ports to remove carbon buildup under specific conditions to 10 years or 120,000 miles, whichever occurs first, from the vehicle's original in-service date for certain 2009-12 Model Year Audi vehicles with 3.2L engine, and certain 2009-2013 Model Year Audi vehicles with 3.0T engines. The vehicle's original in-service date is defined as the date the vehicle was delivered to either the original purchaser or the original lessee; or if the vehicle was first placed in service as a "demonstrator" or "company" car, on the date such vehicle was first placed in service. The warranty extension is fully transferable to subsequent owners. Audi has determined that under certain driving conditions, carbon buildup can occur in the engine cylinder head secondary airports. Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of the on-board diagnostic system. In some locales, an illuminated MIL could cause the vehicle to fail an IM emissions inspection, vehicle registration application could be denied. Audi will diagnose, and if necessary clean the engine cylinder head secondary air ports to remove the carbon buildup at no cost to the customer as long as the vehicle is within the time and mileage limits of the warranty extension. This warranty extension covers only the diagnosis and cleaning of the cylinder head secondary air ports to remove the carbon buildup. Reimbursement is applicable only to the repairs described in this Warranty Bulletin.

Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL. In some locales, an illuminated Malfunction Indicator Lamp could cause your vehicle to fail an IM emissions inspection, and your vehicle registration application could be denied. Please be aware that other conditions (unrelated to the issue described in this letter) may cause the MIL in your vehicle to illuminate. Customers should be prepared to cover all diagnosis and repair costs for these other, unrelated conditions.

On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. Install new manifold actuators.

vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24Z6 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on.

vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24Z6 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles with a 3.0L TFSI engine produced during a certain period, it is possible that the membrane on the vacuum actuator for the intake manifold flaps may tear. As a result, the intake manifold flaps do not function and the engine indicator light turns on.

A quality package has been defined for Audi vehicles with a 4.0L TFSI engine manufactured within a specific period. Perform quality update(s) to vehicle as required, as per applicable criteria shown in ElsaWeb.

This Update is in effect until removed. Procedure is valid only for vehicles that show the 19J1 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. A quality package has been defined for Audi vehicles with 4.0L TFSI engine manufactured within a specific period.

Engine and ignition shut off when driver's door is opened. Electronic Parking Brake (EPB) activates when driver's door is opened (A6/A7/S6/S7 only).

Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300C (572F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies.

The self-leveling system can no longer be adjusted with the MMI. The compressor for the self-leveling system continues to run after the engine has been switched off and the vehicle has been locked. DTCs may be stored in the level control system module, J197 (address word 34). Because of poor performance or failure of the air suspension compressor, the vehicle ride height cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected.

Engine and ignition shut off when driver's door is opened. Electronic Parking Brake (EPB) activates when driver's door is opened (A6/A7/S6/S7 only).

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

This condition occurs on vehicles with air suspension (PR-1BK) if the damper was very warm when the engine was switched off. The noise disappears as the damper warms up, after compressing once or twice. Bubbles are created in the oil because of temperature fluctuations, particles, and high oil flow speed. The bubbles gather around the damping adjustment valve when the engine is switched off. When the vehicle is started again, the cold oil prevents the bubbles from being dispersed quickly, which reduces the hydraulic damping. The reduced hydraulic damping causes the armature in the damper to vibrate, which creates squeaking noises. As soon as the bubbles have been dispersed, the hydraulic damping works fully and the noise disappears.

Please refer to the following information for the workaround procedures until this concern is repaired on Brand DVD V19.48.

content (energy density) being reduced. This reduction in the energy content, which is due to factors. Revised header. Added Model years

batteries.

programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.

Production Solution New software for the ECM and TCM addressed the condition.

Production Solution New software for the ECM and TCM addressed the condition.

Production Solution New software for the ECM and TCM addressed the condition.

range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

Improved software for the comfort system central control module, J393 (address word 46) in production. Service software update will follow at a later date (to be determined).

Incorrect coding in control module after software update (DTC P1749 stored in TCM)

This fault is only a diagnostic error. The fault will not affect vehicle performance.

verification steps to ensure that the vehicle is configured correctly. For additional information on known current draw issues, refer to the following TSBs: ? 2014127: 27 Battery dead or low after returning to the vehicle (2007 A6, A8, Q7) ? 2019143: 27 Battery discharged on some vehicles with Advanced Key (2005 - 2008 A6, Q7)

This document also applies to the 2015 A3 Cabriolet and the 2015 A4 Cabriolet.

Vehicles also include 2015 A3 Cabriolet and 2012 RS7,

cabriolet, or Q5 vehicle only reaches 2G service when in metropolitan areas. This bulletin applies only to model year 2011-2013 A8, 2012-2013 Q7, and 2013 A4, A5, A5 cabriolet, and 2013 Q5 vehicles. For 2012-2013 A6 and A7 vehicles see TSB 2039515. The model year 2014 A8 is not included in this repair. Model year 2014 was the last year before the A8 product improvement and ElsaPro may classify these vehicles as model year 2013 because these vehicles are the same from a technical and design standpoint. But unlike the model year 2013 vehicles, the model year 14 vehicles already have the updated telephone module in the MMI. Recently, T-Mobile (the service provider for Audi connect) has repurposed some of the GSM spectrum (3G on 2100Mhz band) to maximize 4G LTE coverage in certain metropolitan areas. Devices that do not support 3G service on the 1900MHZ band (including MMI main units of the vehicles to which this bulletin applies) will only receive 2G service when the switch is completed. The change currently only affects the markets listed above, but will affect other markets in coming years. This bulletin will be updated to include these markets as changes occur.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.

Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D).

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

Call quality using the hands-free function is poor. Additionally, voice-activated functions may be restricted. The driver sounds muffled. The voice of the driver is quiet. The driver?s voice is accompanied by background interference. Voice-activated commands are not recognized. Various malfunctions can result from the normal airflow out of the center instrument panel vents that are directed upward at the microphones in the roof module, and can limit microphone sensitivity.

The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.

The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.

DTC B200047 (Control unit faulty) is stored in the sensor electronics control module, J849 (address word 3B). With software level 0053, the J849 control module may store DTC B200047 even though the control unit is not faulty.

On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.

On Audi vehicles manufactured within a specific period, the refrigerant pressure sensor for the air conditioner may fail after a period of time. As a result, the air conditioner compressor is switched off. This Update is in effect until removed.

The yellow warning for electromechanical parking park (EPB) appeared once in the instrument cluster. The warning turned off after the ignition was cycled, and there have not been additional occurrences. EPB function was not affected. The adaptive cruise control (ACC) was inoperative once, but it resumed proper operation after the ignition was cycled, and there have not been additional occurrences. DTCs are logged in the EPB control module. There is an issue with the software in the EPB control module that occurs one time. Because the issue only occurs once, replacing the control module could cause an additional occurrence.

Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), the screen freezes briefly. * After the ignition is switched on (shortly after the phone automatically reconnects with the vehicle). * After the phonebook has downloaded. * When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. The command "Call <Name from directory>" is a global MMI command that is available in the telephone menu and main menu screens. If either menu is displayed, the message can appear when the voice recognition button (push to talk) on the steering wheel is pressed.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the programmed Homelink buttons no longer functions. The LED on the Homelink button that is no longer functioning now flashes slowly, indicating that no programming is stored. The customer's transmitter operates at 295Mhz. No DTCs are stored in any control units. At the workshop, the Homelink system can be programmed to the workshop garage door successfully. No trouble is found. The garage door opener control module, J530, was designed with an operational frequency range in which the 295Mhz frequency works correctly during the initial programming of the system. Over time, the transmitting frequency can drift out of range (especially in warmer climates), causing the system to lose its programming.

module, J852, has been calibrated, the windshield has been replaced, or the air suspension level sensors have been adapted. A DTC for incorrect calibration may be stored in the camera control module (address word 85). The camera control module has not been properly calibrated; there is no technical problem.

On certain Audi A6 and A8 vehicles equipped with an electric sun blind for the rear window (3Y2, 3Y5, 3Y8), the blind may stop functioning if it is fully extended several times in quick succession. Update software for the comfort system central control module.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Additionally, voice-activated functions may be restricted. The driver sounds muffled. The voice of the driver is quiet. The driver's voice is accompanied by background interference. Voice activated commands are not recognized. Various malfunctions can result from the normal airflow out of center instrument panel vents that are directed upward at the microphones in the roof module, which can limit microphone sensitivity.

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.

Customer complains of a "popping" noise from the radio followed by 10-15 seconds of no audio. The concern can happen in any audio source. Vehicle is equipped with MMI 3G or MMI 3G+ infotainment systems. Vehicle is not equipped with Bose or Bang & Olufsen sound systems. An ignition cycle is not required for audio to resume.The problem originates in the HD radio code, which can create a "resetting" within the radio unit. Because the tuner is always active in the background, the problem can occur regardless of the audio source or if the HD radio is on or off. It can also occur at any point that the MMI is on, but not necessarily active. For example, the customer opens a door and the MMI starts up. Even though the system is not ?on? because the ignition is not active, the tuner is running and can create the effect.

On Audi vehicles with lane change assist manufactured within a specific period, the lane change assist control module may fail in individual cases after a period of time.

stored in the TCM.

TCM.

No faults stored and concern is reproducible.

Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced.

In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. The DTCs are stored due to an issue with the transmission control module software.

In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction.

After ignition cycle, the warning message is no longer present. The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. The DTCs are stored due to an issue with the transmission control module software.

Rough downshifts when the vehicle is slowed to a stop.

There is no customer complaint about the gearbox. The gear lever display flashes. The following message is shown: "gearbox problem, journey can be continued with restrictions". This is a generic message in the instrument cluster that a transmission fault has occurred and Limp Home Mode might be activated if the malfunction continues.

Calibration of the transmission control module software.

Specific DFCCs are stored as a result of the following situations: - DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is being maneuvered in or out of a parking spot). - DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a low diagnosis threshold. - DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to a low diagnosis threshold.

Further TCM software calibration to improve shift concerns.

The gear lever display flashes. The message "gearbox problem, journey can be continued with restrictions" is shown.

Customer may report transmission warning lamp illuminated in instrument cluster.

Specific DFCCs are stored as a result of the following situations: ? DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is being maneuvered in or out of a parking spot). ? DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a low diagnosis threshold. ? DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to a low diagnosis threshold.

This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.

Specific DFCCs are stored as a result of the following situations: ? DTC P060A00 with DFCC 8692 can be logged when a driving mode (Drive or Reverse) is selected within one second of selecting Neutral, while the vehicle rolls at a speed less than 2 mph (such as when the vehicle is being maneuvered in or out of a parking spot). ? DTC P060A00 with DFCC 8694 can be logged when the gear is quickly changed from Park to Neutral, due to a low diagnosis threshold. ? DTC P060A00 with DFCC 12480 can be logged when the gear is changed using the Tiptronic function, due to a low diagnosis threshold.

DTC P074100 (Torque Converter Clutch Circuit Performance or Stuck Off) is stored in TCM. Diagnostic error in TCM software.

Fault code P074100 Torque Converter Clutch Circuit Performance or Stuck Off is stored in TCM.

A3 Sedan, S3 Sedan, TT Coupe, 2017 Q7, TT Coupe, 2018 S7, S4 Sedan, S5 Coupe, S5 Sportback, S5 Cabriolet, S6

A3 Sedan, S3 Sedan, TT Coupe, 2017 Q7, TT Coupe, 2018 S7, S4 Sedan, S5 Coupe, S5 Sportback, S5 Cabriolet, S6

Customer may report transmission warning lamp illuminated in instrument cluster. Fault code P074100 Torque Converter Clutch Circuit Performance or Stuck Off is stored in TCM.

The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.

The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.

Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module (TCM).

Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced. No faults are stored. TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted.

The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.

Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.

Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration concerns. Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration concerns.

Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 "Torque Converter Clutch Circuit Performance" or "Stuck Off" is stored in TCM. The fault occurs with ATF temperature below 60o C. Check for this temp range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 "Torque Converter Clutch Circuit Performance" or "Stuck Off" is stored in TCM. The fault occurs with ATF temperature below 60o C. Check for this temp range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module, J217 (02). If DFCCs do not match exactly, this TSB does not apply.

There is no customer complaint about the gearbox. The gear lever display flashes. The following message is shown: "gearbox problem, journey can be continued with restrictions". DTCs are stored in the gear shift control module, J587 (address word 81). New software in the gear shift control module addressed the condition.

Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module (TCM), J217 (02). If DFCCs do not match exactly, this TSB does not apply. The DTCs are stored due to an issue with the transmission control module software.

Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Customer may report harsh downshifts while braking or harsh 1-2 upshift under acceleration concerns. Further TCM software calibration to improve shift concerns.

Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module, J217 (03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

condition of the selector lever sensors when the ignition is switched on. As a result, the gearbox warning lamp lights up and it is no longer possible to engage a gear. Update the software for the selector lever control module.

programming function: A software fix is needed to correct the issue: The ODIS Audi Brand update 2.41.1 is setting a ODS5003E error code when you perform the 90TV SVM flash.

decomissioned).

software update for any TSB or Update.

software update for any TSB or Update.

2016-2020 A3, 2016-2020 A3 Cabrio, 2016 A3 Sportback, 2016-2020 A4, 2016-2020 A4 allroad, 2016-2012 A4 Avant, 2016-2020 A5 Cabrio, 2016-2020 A5 Coupe, 2018-2020 A5 Sportback, 2016-2020 A6, 2016-2020 A7, 2016-2020 A8, 2016-2020 e-tron, 2019-2020 e-tron quattro, 2016-2020 Q3, 2016-2020 Q5, 2016-2020 Q7, 2016-2020 Q8, 2016-2020 R8 Coupe, 2016-2020 R8 Spyder, 2017-2019 RS3, 2016-2020 RS5, 2016-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2016-2020 S5 Cabrio, 2016-2020 S5 Coupe, 2018-2020 S5 Sportback, 2016-2020 S6, 2016-2020 S7, 2018-2021 SQ5, 2016-2020 TT Coupe, 2016-2020 TT Roadster

Occasional "System too rich" entries.

Occasional "System too rich" entries.

Occasional "System too rich" entries.

Occasional "System too rich" entries.

Occasional "System too rich" entries.

Occasional "System too rich" entries.

Occasional "System too rich" entries.

Occasional "System too rich" entries.

The revision is in regards to the manifold actuator.

systems control unit, camera(s), LIDAR, and/or sensor(s) which enable automatic emergency braking functionality.

systems control unit, camera(s), LIDAR, and/or sensor(s) which enable automatic emergency braking functionality.

switch; DTC C100C07 and/or C100C29.

(crawling when pulling away or briefly before standstill).

temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.

headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.

Customer may report hearing a high-pitched squeal or squeak from the front brake system when brakes are used with light to moderate effort. Various parts have been replaced under warranty for the condition noted above. In an effort to gain information, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.

In some cases, the noise may be intermittent and difficult to reproduce.

There are conflicting tolerances in the alignment of pin and hole on the front brake discs.

DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 (address word 53). According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. Test plan "19-Read Data Bus Keep-Awake Manager", identifies the EPB control module as keeping the data bus active for prolonged periods of time.

Various parts have been replaced under warranty for the condition noted above. In an effort to gain information, we are asking that you contact the Audi Technical Assistance Center (TAC) before replacing any parts. This will assist us in diagnosing any potential issues with the condition noted above.

Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 (address word 53). According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. Test plan "19-Read Data Bus Keep-Awake Manager", identifies the EPB control module as keeping the data bus active for prolonged periods of time.

If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.

The message "ACC and braking guard: unavailable at this time. No sensor vision" appears in the instrument cluster. DTC is logged in the distance regulation control module, J428 (address word 13).

repair is not needed.

while driving at highway speeds from 55 - 80 mph.

wheel isn't heating evenly.

maneuvered.

outside influence is not covered under warranty.

outside influence is not covered under warranty. 2008-2020 A3, 2015-2020 A3 Cabrio, 2005-2016 A3 Sportback, 2005-2020 A4, 2010-2020 A4 allroad, 2005-2012 A4 Avant, 2005-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2005-2020 A6, 2005-2011 A6 Avant, 2008-2020 A7, 2005-2020 A8, 2008-2019 e-tron, 2019-2020 e-tron quattro, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2007-2020 S6, 2008-2020 S7, 2007-2009 S8, 2018-2020 SQ5, 2004-2020 TT Coupe, 2004-2020 TT Roadster, 2012 TT/RS Coupe

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.

Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.

Vehicle pulls - left or right. Steering wheel not leveled or off-center. In some cases both concerns may be reported. the alignment concern is due to outside influence (e.g. accident), this TSB does not apply.

Customers may report the following conditions on vehicles with less than 6000 miles. In some cases these conditions may be noticed at PDI. Vehicle pulls - left or right. Steering wheel not leveled or off-center. If the alignment concern is due to outside influence (e.g. accident), this TSB does not apply.

Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.

symbol or emoticon is used in the name field for contact(s).

See owner's manual" is displayed in the instrument cluster without DTCs.

This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.

following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.

Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro

level."

level.?

level.?

navigation.

level.?

for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.

The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.

The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.

The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.

MMI 3G+ Sound system "popping" and various other technical Issues (K0715 Update). Only apply this bulletin to vehicles if the customer complaint is in the correct group. Applying the update to vehicles outside of the appropriate group can cause repeat repairs and the warranty claim may be denied. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). The applicable vehicles can be clearly identified by the SIM card slot on the faceplate of the front MMI mainunit.

functioning if it is fully extended several times in quick succession. This Update is in effect until removed. Procedure is valid only for vehicles that show the 68E3 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi A6 and A8 vehicles equipped with an electric sun blind for the rear window (3Y2, 3Y5, 3Y8), the blind may stop functioning if it is fully extended several times in quick succession.

functioning if it is fully extended several times in quick succession. This Update is in effect until removed. Procedure is valid only for vehicles that show the 68E3 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi A6 and A8 vehicles equipped with an electric sun blind for the rear window (3Y2, 3Y5, 3Y8), the blind may stop functioning if it is fully extended several times in quick succession.

The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.

The Update is in effect until removed. Procedure is valid only for vehicles that show the 19i9 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicles must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted timeframe stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale.

fail in individual cases after a period of time. The Update is in effect until removed. Procedure is valid only for vehicles that show the 96C8 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicles must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted timeframe stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale.

The Update is in effect until removed. Procedure is valid only for vehicles that show the 19i9 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicles must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted timeframe stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale.

dipped beam is switched on.

fender.

the Mirror Server.

fender.

image of the suction cups used to install the windshield in production.

vehicles equipped with pananormic sunroof.

vehicles equipped with pananormic sunroof.

with the remote.

vehicles equipped with pananormic sunroof.

with the remote.

The trunk cannot be unlocked with the button on the remote, with the button in the driver?s door panel, or with the handle on the lid of the trunk. Vehicles have a ?VALET? button in the glove box that activates the valet parking feature, which prevents unauthorized access to the trunk. When the valet parking feature is activated, the trunk can only be opened mechanically with the key.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

When the window guide seal is not correctly fitted in the rail of the front door, it can lead to increased friction. This increased resistance causes the squeaking noises.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

There are squeaking noises coming from the front door when the window is operated. When the window guide seal is not correctly fitted in the rail of the front door, it can lead to increased friction. This increased resistance causes the squeaking noises.

The movement-activated rear lid opening (also known as "Hands-free trunk release") sporadically is inoperative. This feature is installed on all A8 vehicles with Audi advanced key (PR No. 4I3) from CW 45/2011 production.

In our continuing quest to improve customer satisfaction, we have identified the need to further explain certain vehicle features and technologies with which customers new to the brand may not be familiar. Audi is pleased to provide all dealerships with two in-car video DVD tutorials (one for MY2013 A6/A7 and one for MY2013 A8 models). The tutorials cover some of the most-asked-about vehicle technology and features. These video-accessible topics mirror what can be viewed on the Audi technology Web site: http://auditechnology.com.

The movement-activated rear lid opening (also known as "Hands-free trunk release") sporadically is inoperative. This feature is installed on all A8 vehicles with Audi advanced key (PR No. 4I3) from CW 45/2011 production.

The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the handle is slack.

The knob may be broken. The force required to adjust the vent is greater than the attachment strength of the knob. As a result, the knob may break.

Hardware problems during the installation of new Brand DVDs are minimized if users regularly perform the Windows hard disc maintenance utility ?chkdsk?. If your device has never had hard disc maintenance performed via the Windows ?chkdsk? utility, please perform this maintenance prior to installation of this Brand update, and ensure that it be performed on a regular basis to ensure reliable software functions. Brand DVD V19.48.00 must only be installed on VAS-PC testers that were previously updated with Base V19.01.01. After installation of the Brand DVD, all stored Diagnosis Jobs are erased; therefore complete work beforehand if required. DO NOT install the Brand DVD V19.48.00 on VAS 5051A or 5052 testers.

petrol.

petrol.

State of Minnesota.

diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel pump using the procedure in the Service section of this bulletin.

conditions.

Media files can now be viewed on any smartphone or tablet.

diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel pump using the procedure in the Service section of this bulletin.

conditions.

Media files can now be viewed on any smartphone or tablet.

diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel pump using the procedure in the Service section of this bulletin.

conditions.

Media files can now be viewed on any smartphone or tablet.

The guard minimizes the likelihood that fuel other than ultra-low sulfur diesel will be put into the vehicle. The misfueling guard is designed to remain in a locked position when a nozzle with a diameter typically suited for non-diesel fuels (approximately 13/16?, or 20.6mm) is inserted, to prevent further insertion of the nozzle into the filler neck. A nozzle with a larger diameter typically suited for diesel fuel (approximately 15/16?, or 23.8mm) will unlock the misfueling guard when inserted, allowing the nozzle to be further inserted into the filler neck.

after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for metallic particles in the High Pressure Fuel Pump.

hangers may be a contributing factor. Various noises, such as humming, vibration, and/or rattling are heard coming from under the vehicle or from near the center console area.

hangers may be a contributing factor.

some issues.

performing the TDI emissions modification. - REVISED 12/17/18 to apply to 3.0L models and to remove 2.0L models.

2.0L TDI and 3.0L TDI resale, buyback, TDI Direct, and VCI auction vehicles prior to proceeding with the AEM Emissions Recall. Only create an Audi Technical Assistance Center (TAC) ticket if required by applicable recall.

The parts list was updated to include service numbers.

or center arm rest.

or center arm rest.

While these types of noises could be attributed to a number of components in the vehicle, misaligned front exhaust hangers may be a contributing factor.

Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.

The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.

Customer states that the vehicle cannot be refueled due to difficulty inserting the fuel pump nozzle into the filler neck. Customer may also state that the flap is stuck in a locked position and it cannot be moved with fingers.

taillights.

submissions.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

01800, or B126AF0.

S4 Cabriolet, 2008 RS4 Cabriolet, 2010-2021 A4 allroad, 2018-2021 A5 Sportback, 2010-2012, 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2004-2006 A7, 2004-2011 S7, 2021 RS6 Avant, 2004-2006 S8

2015-2021 A3 Cabriolet, 2015-2018 A3 e-tron, 2011-2021 A4 allroad, 2018-2021 A5 Sportback, 2011-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS6 Avant

2015-2021 A3 Cabriolet, 2016-2018 A3 Sportback, 2018-2021 A5 Sportback, 2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS 6 Avant

01800, or B126AF0.

14s.

but not overfilled.

The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

One or more LEDs in the low beam are inoperative on one side. Internal cooling fan is inoperative in one headlight. DRL inoperative on one side. LED turn signal inoperative in one headlight. Diagnosis of the concern indicates that the headlight is at fault. Connector in the headlight is not properly seated.

for 2.0L and 3.0L TDI vehicles.

resolve a stored DTC.

resolve a stored DTC.

Instructions for vehicle inspection, protection removal, and detailing.

CD or DVD disks do not automatically change from one to the next in the external CD or DVD changer.

This TSB contains information on technician preparation when calling the Audi Technical Assistance Center

2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and 2018-2020 RS5 Cabriolet, 2018-2020 S5 Sportback, 2008 A7, 2008-2011 S7

Wheel bolt requires torque adjustment.

concern.

the concern.

concern.

of the concern.

from the HVAC system.

2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster

a ODIS GFF test plan.

When the vehicle is started, the GPS location or vehicle direction indicated on the MMI navigation map does not match the vehicle?s actual location or direction of travel for a long period of time (often as long as 10 minutes). The issue occurs in open sky, with no large buildings obstructing the sky view. The issue is intermittent, but it can occur for long periods of time during a single day. The issue resolves itself intermittently. The issue typically happens on very warm days when the HVAC system blower is at a medium to high setting (auto or manual), with air being directed out of the panel vents. When the issue occurs, the GPS navigation system satellite reception shows 0 satellites. Due to the infrequency of the issue, this might not be verifiable. (To view the number of satellites being received, go to Nav >> Route >> Select Current Position (first item in list) and scroll up). No DTCs related to the GPS antenna or MMI system are present. The vehicle is an A4 (including S4 and allroad variants), A5 (including Cabriolet, S5, and RS 5 variants), A6 (including S6 variant), A7 (including S7/RS 7 variants), A8 (including long wheelbase, S8, or W12 variants) or Q5 (including SQ5 and hybrid variants). (Q7 and Q3 vehicles are not affected by this condition. See TSB 2030465, 91 MMI3G+ GPS navigation location inaccurate or navigation takes a very long time to acquire location (Q7 or Q3) for Q7 and Q3 vehicles.)

Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.

The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.

The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.

airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.

replacement airbag inflators that are being installed in used vehicles.

airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.

(airbag/seatbelts, accidents, fire and overheat damage).

(airbag/seatbelts, accidents, fire and overheat damage.

(airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe