2003 Audi A8 TSBs

resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).

Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. As a result, application of the brake and accelerator pedals at the same time (brake pedal with left foot and accelerator pedal with right foot) results in the following: ? Brake pedal function (normal at all times) overrides any throttle application. ? Diagnostic Trouble Codes (DTCs) will not be stored. ? When the brake pedal is applied while the accelerator is depressed, engine RPMs will return to idle speeds of 1400 RPMs after approximately two seconds. ? When the accelerator is applied while the brake pedal is depressed, the vehicle accelerates slower than usual (reduced engine torque).

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Electric steering column adjustment is restricted or does not work at all. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. The seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, so the electric steering column adjustment fails.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Oil consumption measurement - Repair Authorization (CA). In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil.

Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens. Damp air settles on the inside of a cold lens, which creates condensation. The headlight circulation system allows air from the outside to flow through the headlights. This open waterprotected ventilation system (needed for pressure compensation) creates different climate zones in the headlight: very warm areas, where the lens is warmed up by the light, and relatively cool areas, where the lens is cooled own by the air flow. Considerable differences in humidity and temperature between the inside and the outside of the headlights, even while driving, can lead to condensation. This is especially true in cold and wet weather, but it can also happen after a car wash, after steam cleaning the engine or the front end, with overnight temperature changes, etc. This phenomenon is more visible on lenses made of clear glass than on lenses with patterns. The moisture does not affect the headlight function (light performance) and does not lead to corrosion or other damage to headlight parts.

Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.

Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.

This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).

Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.

ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE

VEHICLES AFFECTED BY THIS ACTION MAY HAVE IGNITION COILS THAT COULD MALFUNCTION UNDER CERTAIN CONDITIONS. ADDED FINAL MAILING PHASE-8/10 VIN INFORMATION. MODELS A4/CABRIOLET; TT; A3; A8; A6; S4; ALLROAD; RS4; Q7; S6; S8. *PE

VEHICLES AFFECTED BY THIS ACTION MAY HAVE IGNITION COILS THAT COULD MALFUNCTION UNDER CERTAIN CONDITIONS. (ADDED PHASE 7-APRIL 10 VIN INFORMATION).MALFUNCTION INDICATOR LAMP (MIL) WILL ILLUMINATE TO LET YOU KNOW VEHICLE MAY EXPERIENCE SOME DETERIORATION IN PERFORMANCE. SOME CASES, A MALFUNCTIONING IGNITION COIL MAY CAUSE VEHICLE TO EXCEED FEDERAL AND/OR CALIFORNIA EMISSIONS STANDARDS. *PE

ECM SOFTWARE UPDATED WITH MODIFIED MAP CONTROLLED COOLANT THERMOSTAT SPECIFICATIONS. THE TCM SOFTWARE MUST ALSO BE UPDATED TO BE COMPATIBLE WITH THE NEW ECM SOFTWARE LEVEL. POSSIBLE ENGINE COOLANT SCALING IN HVAC SYSTEM. *PE

ENGINE HAS LOW PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. DTCS RELATED TO THE MASS AIR FLOW SENSOR AND FUEL TRIM FAULTS CAN BE RELATED TO (BUT NOT LIMITED TO) THE FOLLOWING CONDITIONS-FALSE INTAKE AIR, OR AIR FILTER ELEMENT VERY DIRTY; FUEL PRESSURE TOO LOW AND MASS AIR FLOW SENSOR FAULT. MODELS INCLUDE ALLROAD 2004-2005. *PE

*TT

2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 Q7, 2019 Q8, 2000-2019 TT, 2008-2018 R8

numbers going forward.

change.

This notice contains information for the accessories operations technical bulletin.

*NJ

*KB

high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.

Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.

DUE TO MODULE CROSS CARRIER AND UNFAVORABLE TOLERANCES TO STEERING COLUMN. MODEL 2003-2010 A8, 2005-2011 A6, 2007-2014 Q7. *PE

IF THIS HAPPENS, THE MALFUNCTION INDICATOR LAMP (MIL) WILL ILLUMINATE TO LET YOU KNOW THAT THE VEHICLE MAY EXPERIENCE SOME DETERIORATION IN PERFORMANCE. IN SOME CASES, A MALFUNCTIONING IGNITION COIL MAY CAUSE A VEHICLE TO EXCEED FEDERAL AND/OR CALIFORNIA EMISSIONS STANDARDS. *PE UPDATED 8/9/10. *PE UPDATED 8/11/10. *PE UPDATED 11/8/10. *PE UPDATED 11/10/10. *PE UPDATED 1/10/11. *PE

SVM IS A PROCESS TO UPDATE THE PROGRAMMING IN FLASHABLE (RE-PROGRAMMABLE) CONTROL MODULES AND/OR TO DOCUMENT CHANGES IN SOFTWARE LEVELS IN AUDI VEHICLES. THIS SYSTEM USES THE VAS 5051B OR VAS 5052 DIAGNOSTIC TOOLS TO SEND VEHICLE SPECIFIC DATA TO THE SVM DATABASE, TO DOWNLOAD INSTRUCTIONS FROM THE SVM DATABASE, AND TO FLASH CONTROL UNITS FOR IDENTIFIED SOFTWARE UPDATES. *PE

ITS A PROCESS TO UPDATE THE PROGRAMMING IN FLASHABLE (REPROGRAMMABLE) CONTROL MODULES AND/OR TO DOCUMENT CHANGES IN SOFTWARE LEVELS IN ALL AUDI VEHICLES. *PE

software update for any TSB or Update.

software update for any TSB or Update.

This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.

DETAILING THE GENERAL PROCESS FOR CARRYING OUT A SOFTWARE VERSION MANAGEMENT (SVM) SOFTWARE UPDATE FOR ANY TSB OR REQUIRED VEHICLE UPDATE (RVU). TROUBLESHOOTING INFORMATION IS INCLUDED. *PE

State of Minnesota.

conditions.

Media files can now be viewed on any smartphone or tablet.

conditions.

Media files can now be viewed on any smartphone or tablet.

conditions.

Media files can now be viewed on any smartphone or tablet.

Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.

The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.

headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.

If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.

Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.

GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE

*JS

Wheel bolt requires torque adjustment.

Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.

TORQUE STICKS AND TORQUE EXTENSION BARS ARE NOT APPROVED BY AUDI OF AMERICA, INC. AND SHOULD NOT BE USED TO APPLY TORQUE TO WHEEL BOLTS. ALL AUDI MODELS INCLUDED. *PE

This TSB contains information on technician preparation when calling the Audi Technical Assistance Center

VIN plate and/or B-Pillar Safety Certification label requires replacement.

Technician preparation when calling the Audi Technical Assistance Center (TAC).

Leather upholstery is dirty or stained.

Rear center armrest lid does not latch. Unfavorable tolerance between the release and the armrest.

The customer may report that the Easy Entry function of the power adjustable steering column intermittently does not work.

The customer may report that the Easy Entry function of the power adjustable steering column intermittently does not work.

(airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe

*KB

OVER TIME RESISTANCE VARIANCE WITHIN SIDE IMPACT AIRBAG CONNECTOR CAN CAUSE THE AIRBAG WARNING LIGHT ON INSTRUMENT PANEL TO COME ON AND STAY ON, EVEN THOUGH SIDE IMPACT AIRBAG SYSTEM FUNCTIONS NORMALLY. *PE

Automatic transmission fluid is leaking at the sump pan gasket.

Automatic transmission fluid is leaking at the sump pan gasket. As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak.

The MMI screen will not open or close at all. supplier error affecting certain MMI display mounts can cause the internal gear of the mount to get stuck after a few cycles. MMI display mounts produced between October 2012 and September 2013 with part number 4E0857273F are affected. This vehicle is out of production. This issue only affected spare parts.

The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.

*KB

Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.

*PE

*KB

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.