2012 Audi A7 TSBs

the height to which the vehicle has been flooded.

tester refers to this reportin gobligation or to TPI 2033392.

not activate.

mode.

not activate.

Assistnce Center (TAC).

(TAC).

(Ghost faults).

whining, or similar interference.

No DTCs are stored.

level is correct.

The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

crankcase pressure can lead to the above described DTC codes.

to appear.

The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

crankcase pressure can lead to the above described DTC codes.

to appear.

The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

crankcase pressure can lead to the above described DTC codes.

to appear.

radiator (Figure 1).

radiator (Figure 1).

Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. ?Set? button on cruise control stalk does not work.

system.

restriction.

exist or it is inoperative/constant warning.

expansion tank cap.

it from occurring again.

exist or it is inoperative/constant warning.

toothed belt.

exist or it is inoperative/constant warning.

exist or it is inoperative/constant warning.

Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.

2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 Q7, 2019 Q8, 2000-2019 TT, 2008-2018 R8

higher than 2.

2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster

2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2008-2020 A6, 2008-2011 A6 Avant, 2008-2020 A7, 2008-2020 A8, 2008-2019 e-tron, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2008-2012 S4, 2008-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2008-2020 S6, 2008-2020 S7, 2008-2009 S8, 2018-2021 SQ5, 2008-2020 TT Coupe, 2008-2020 TT Roadster, 2012 TT/RS Coupe

logged.

numbers going forward.

higher than 2.

passenger side from heating properly with DTC B10D004 or B11D501.

higher than 2.

higher than 2.

The compartment was bumped or kicked while open, causing it to disengage.

change.

This is for all keys and there is no relevant DTCs stored.

passenger side from heating properly with DTC B10D004 or B11D501.

higher than 2.

exist or it is inoperative/constant warning.

expansion tank cap.

This notice contains information for the accessories operations technical bulletin.

vehicles with 0BK & 0BL Gearbox.

stored in the ECM P030000.

brakes.

working; mileage below 50 km/32 miles.

working; mileage below 50 km/32 miles.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

that the oil level is not okay.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

that the oil level is not okay.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

that the oil level is not okay.

If the natural vacuum leak detection (NVLD) system cannot detect this natural vacuum during the system self-test, the DTC will be stored in the ECM.

The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures.

consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

When changing the oil filter and installing the new filter seal(s) in the oil filter housing, special attention is required.

consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner? s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods.

The adaption must be reset after the engine is installed.

a restriction.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

a restriction.

The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.

Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).

Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. As a result, application of the brake and accelerator pedals at the same time (brake pedal with left foot and accelerator pedal with right foot) results in the following: ? Brake pedal function (normal at all times) overrides any throttle application. ? Diagnostic Trouble Codes (DTCs) will not be stored. ? When the brake pedal is applied while the accelerator is depressed, engine RPMs will return to idle speeds of 1400 RPMs after approximately two seconds. ? When the accelerator is applied while the brake pedal is depressed, the vehicle accelerates slower than usual (reduced engine torque).

If the natural vacuum leak detection (NVLD)

connector.

connector.

on the circumstances under which DTC P244000 and/or P244200 were stored.

on the circumstances under which DTC P244000 and/or P244200 were stored.

Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

The MIL is on. DTC P045600 (very small EVAP leak) stored in engine control module. No leaks found in the EVAP system. Software update needed.

The MIL is on. DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) is stored in the engine control module (ECM). The diagnostic limitations were too narrow.

Audi advanced key (keyless entry) is inoperative on all doors, but the engine can be started with the keyless starting system (keyless go). The keyless starting system (keyless go) is a standard feature; Audi advanced key is an optional feature. All vehicles have an engine start-stop button (-E408-) and touch sensor surface on the outer door handles, but this does not mean that the optional Audi advanced key function is installed.

The MIL is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults may be stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss as a result of coolant migration in the electrical harness, faults in 08-Heating and Air Conditioning Electronics that result from coolant migration in the electrical harness, or a faulty N82 control valve.

MIL on. DTC P045600 (very small EVAP leak) stored in engine control module (ECM), J623 (address word 01). No leaks found in the EVAP system. Software update needed.

There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.

(address word 01).

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.

The customer may report that after a specific temperature is selected in AUTO mode, the resulting airflow and temperature are uncomfortable. The customer complaint is subjective and may be difficult to diagnose during a road test. Perform a test drive with the customer both before and after this repair to ensure a thorough understanding of the customer's concern. DTCs for mechanical malfunction of one or more air distribution control motors may be stored in the air conditioning/heating control unit, J255 (address word 08).

MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The engine is not running roughly. However, fault codes are stored in the engine control module (ECM). The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfire adaption are not automatically reset when the memory is deleted. The adaption must be reset after the engine is installed.

MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

MIL on. DTC P045600 (very small EVAP leak) stored in engine control module (ECM), J623 (address word 01). No leaks found in the EVAP system. Software update needed.

MIL on. A cylinder misfire fault (DTC P0301 - P0306) with DTC P130A is stored in the engine control module (ECM), J623 (address word 01).

Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.

The noises may be intermittent, and may depend on the outside temperature, the position of the flaps, etc. The noises are subtle, and they may not be heard if the audio system is on or if the vehicle is moving. The noises may be caused by a section of the noise insulation on the heating and air conditioning unit.

cover cleaning of the engine cylinder head secondary air ports to remove carbon buildup under specific conditions to 10 years or 120,000 miles, whichever occurs first, from the vehicle's original in-service date for certain 2009-12 Model Year Audi vehicles with 3.2L engine, and certain 2009-2013 Model Year Audi vehicles with 3.0T engines. The vehicle's original in-service date is defined as the date the vehicle was delivered to either the original purchaser or the original lessee; or if the vehicle was first placed in service as a "demonstrator" or "company" car, on the date such vehicle was first placed in service. The warranty extension is fully transferable to subsequent owners. Audi has determined that under certain driving conditions, carbon buildup can occur in the engine cylinder head secondary airports. Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of the on-board diagnostic system. In some locales, an illuminated MIL could cause the vehicle to fail an IM emissions inspection, vehicle registration application could be denied. Audi will diagnose, and if necessary clean the engine cylinder head secondary air ports to remove the carbon buildup at no cost to the customer as long as the vehicle is within the time and mileage limits of the warranty extension. This warranty extension covers only the diagnosis and cleaning of the cylinder head secondary air ports to remove the carbon buildup. Reimbursement is applicable only to the repairs described in this Warranty Bulletin.

Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL. In some locales, an illuminated Malfunction Indicator Lamp could cause your vehicle to fail an IM emissions inspection, and your vehicle registration application could be denied. Please be aware that other conditions (unrelated to the issue described in this letter) may cause the MIL in your vehicle to illuminate. Customers should be prepared to cover all diagnosis and repair costs for these other, unrelated conditions.

A drain valve was not fitted at the rear on affected Audi A7 vehicles manufactured within a specific period. Install a drain valve in the battery tray.

This Update is in effect until removed. Procedure is valid only for vehicles that show the 53B6 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. A drain valve was not fitted at the rear on Audi A7 vehicles manufactured within a specific period.

The customer may report that after selecting a specific temperature in AUTO mode, the resulting airflow and temperature are uncomfortable. The customer complaint is subjective and may be difficult to diagnose during a road test. Please test drive with the customer before as well as after this repair to ensure a thorough understanding of the customer's concern. At certain outside temperatures and operating conditions, the temperature in the passenger compartment fluctuates. This is caused by the unventilated sensor in the air conditioning control panel. There may also be DTCs stored for mechanical malfunction of one or more air distribution control motors in (08) air conditioning/heating control unit.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are replaced.

MIL on. DTC P0456 (very small EVAP leak) stored in engine control module (ECM), J623 (01). No leaks found in the EVAP system.

MIL on. DTC P0456 (very small EVAP leak) stored in engine control module (ECM), J623 (01). No leaks found in the EVAP system. Software update needed.

MIL on. DTC P0456 (very small EVAP leak) stored in engine control module, J623 (01). No leaks found in the EVAP system. Software update needed.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The bracket for the starter motor wiring harness has a locating tab that can vibrate.

MIL on. DTCs are stored in the engine control module (ECM). The faults are caused by an incorrect software setting and can occur under certain driving conditions. In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.

Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Under extreme driving conditions, such as a driving profile of mainly short distance (stop and go) driving high crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner? s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods.

The customer may report that after selecting a specific temperature in AUTO mode, the resulting airflow and temperature are uncomfortable. The customer complaint is subjective and may be difficult to diagnose during a road test. Please test drive with the customer before as well as after this repair to ensure a thorough understanding of the customer? s concern. At certain outside temperatures and operating conditions, the temperature in the passenger compartment fluctuates. This is caused by the unventilated sensor in the air conditioning control panel. There may also be DTCs stored for mechanical malfunction of one or more air distribution control motors in (08) air conditioning/heating control unit.

The customer may report that after selecting a specific temperature in AUTO mode, the resulting airflow and temperature are uncomfortable. The customer complaint is subjective and may be difficult to diagnose during a road test. Please test drive with the customer before as well as after this repair to ensure a thorough understanding of the customer? s concern. At certain outside temperatures and operating conditions, the temperature in the passenger compartment fluctuates. This is caused by the unventilated sensor in the air conditioning control panel. There may also be DTCs stored for mechanical malfunction of one or more air distribution control motors in (08) air conditioning/heating control unit.

Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods.

Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens. Damp air settles on the inside of a cold lens, which creates condensation. The headlight circulation system allows air from the outside to flow through the headlights. This open waterprotected ventilation system (needed for pressure compensation) creates different climate zones in the headlight: very warm areas, where the lens is warmed up by the light, and relatively cool areas, where the lens is cooled own by the air flow. Considerable differences in humidity and temperature between the inside and the outside of the headlights, even while driving, can lead to condensation. This is especially true in cold and wet weather, but it can also happen after a car wash, after steam cleaning the engine or the front end, with overnight temperature changes, etc. This phenomenon is more visible on lenses made of clear glass than on lenses with patterns. The moisture does not affect the headlight function (light performance) and does not lead to corrosion or other damage to headlight parts.

On Audi vehicles with electromechanical power steering manufactured within a specific period, an irregularity detected by the diagnosis function can result in an implausible status immediately after the engine is started. This causes the warning lamp for the electromechanical power steering to light up. There is no loss of steering functionality. Update the power steering control module (J500) software.

This Update is in effect until removed. Procedure is valid only for vehicles that show the 48K4 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles with electromechanical power steering manufactured within a specific period, an irregularity detected by the diagnosis function can result in an implausible status immediately after the engine is started. This causes the warning lamp for the electromechanical power steering to light up. There is no loss of steering functionality.

MIL on, with DTCs stored in the 01 (Engine Control Module). Under extreme driving conditions, such as a driving profile of mainly short distance (stop and go) driving high crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner? s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods.

To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4 F (2 C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.

The customer may report that after a specific temperature is selected in AUTO mode, the resulting airflow and temperature are uncomfortable. DTCs for mechanical malfunction of one or more air distribution control motors may be stored in the air conditioning/heating control unit, J255 (address word 08). At certain outside temperatures and in certain operating conditions, the temperature in the passenger compartment fluctuates. This fluctuation is caused by the unventilated sensor in the air conditioning control panel.

The MIL is on. DTC P164B(00) is stored in the engine control module.The oil pressure switch is defective.

Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.

Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

The MIL is on. Vehicle will not start. DTC P068A00 is stored in the ECM. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.

The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.

DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.

The customer may report that after a specific temperature is selected in AUTO mode, the resulting airflow and temperature are uncomfortable. The customer complaint is subjective and may be difficult to diagnose during a road test. Perform a test drive with the customer both before and after this repair to ensure a thorough understanding of the customer's concern. DTCs for mechanical malfunction of one or more air distribution control motors may be stored in the air conditioning/heating control unit, J255 (address word 08). At certain outside temperatures and in certain operating conditions, the temperature in the passenger compartment fluctuates. This fluctuation is caused by the unventilated sensor in the air conditioning control panel.

Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module (address word 02). Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.

The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The MIL is on. DTCs are stored in the ECM. Under extreme driving conditions (such as short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.

The MIL is on. DTC P045600 (very small EVAP leak) stored in engine control module (ECM), J623 (address word 01). No leaks found in the EVAP system. Software update needed.

Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

The MIL is on. DTCs are stored in the engine control module (ECM). The faults listed above are caused by an incorrect software setting and can occur under certain driving conditions. In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated. The MIL will illuminate and DTC P112800 and/or DTC P113000 will be stored when the intake air temperature is high. Freeze frame data will show an intake air temperature above 104F (40C). The MIL will illuminate and DTC P008700 will be stored when the coolant temperature is high. Freeze frame data will show a coolant temperature above 212F (100C). There are no condition restrictions for DTC P244000 or DTC P244200.

This Update is in effect until removed. Procedure is valid only for vehicles that show the 24V2 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be in New Federal Emissions Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. On Audi vehicles with 3.0L TFSI engine manufactured within a specific period, it is possible that the dynamic oil level warning function is faulty. This can cause the oil level warning lamp to light up even though there is sufficient oil in the engine.

There are 79,232 Audi vehicles affected in the U.S. by this Update. Rough idle or reduced driving power and, in turn, an illuminated Malfunction Indicator Lamp (MIL) on the instrument cluster due to the presence of specific fault codes caused by this component. Inspect and replace ignition coils as required.

MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

MIL on. DTCs are stored in the engine control module (ECM). Under extreme driving conditions (such short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.

Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant.

programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.

Software update needed.

New software in the ECM addressed the condition.

New software in the ECM addressed the condition.

Software update needed.

New software in the ECM addressed the condition.

New software in the ECM addressed the condition.

Software update needed.

New software in the ECM addressed the condition.

New software in the ECM addressed the condition.

New pressure sensors in production: ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, that are separate (two components): part numbers 8K0906253 and 8K0906253B supersede to 8K0906253D. ? For vehicles with a fuel tank pressure sensor, G400, and a fuel tank leak detection control module, J909, which are integrated (one component): part numbers 8K0906253A and 8K0906253C supersede to 8K0906253E.

the minimum level (when measured with special tool T40178). ? There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.

the minimum level (when measured with special tool T40178). ? There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.

range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

Improved software for the comfort system central control module, J393 (address word 46) in production. Service software update will follow at a later date (to be determined).

verification steps to ensure that the vehicle is configured correctly. For additional information on known current draw issues, refer to the following TSBs: ? 2014127: 27 Battery dead or low after returning to the vehicle (2007 A6, A8, Q7) ? 2019143: 27 Battery discharged on some vehicles with Advanced Key (2005 - 2008 A6, Q7)

MMI3G+ bluetooth security profile.

This document also applies to the 2015 A3 Cabriolet and the 2015 A4 Cabriolet.

Vehicles also include 2015 A3 Cabriolet and 2012 RS7,

MMI3G+ bluetooth security profile.

The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently. Intermittently, the MMI system does not appear to remember that the user?s myAudi PIN has already been entered, and it requires the user to enter the PIN again. The voice recognition system does not easily recognize commands spoken by the driver. This condition can be consistent or intermittent. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations, accessing weather or other online information, or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered. 2016 A6 and A7 vehicles have a known software issue that requires the myAudi PIN to be entered with each ignition cycle. Multiple voice recognition training sessions can be stored in the MMI for different users when different phones are Bluetooth-paired during each training session. If no phone is paired, the training session will be stored under a default profile. Thi

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

MMI3G+ bluetooth security profile.

high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.

disconnected or replaced.

The seatbelt warning light is illuminated, but the passenger seatbelt is buckled. The seatbelt warning chime is not on. This bulletin only applies to vehicles equipped with navigation system. Software of the instrument cluster control module needs to be updated.

Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D).

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

DTCs are logged in the rearview camera system control module. DTCs for the affected camera may also be logged. Incorrect component.

The message ?Oil minimum warning, add one quart of oil? appears in the instrument cluster, but the oil level is above the minimum level (when measured with special tool T40178). There are no DTCs related to oil level stored in the ECM memory. The oil level sensor is defective.

The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.

The exterior door handle touch sensors (Audi advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.

The yellow warning for electromechanical parking park (EPB) appeared once in the instrument cluster. The warning turned off after the ignition was cycled, and there have not been additional occurrences. EPB function was not affected. The adaptive cruise control (ACC) was inoperative once, but it resumed proper operation after the ignition was cycled, and there have not been additional occurrences. DTCs are logged in the EPB control module. There is an issue with the software in the EPB control module that occurs one time. Because the issue only occurs once, replacing the control module could cause an additional occurrence.

The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". The lock command history is stored in the convenience system control module (J393).

Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

The vehicle alarm activates for no reason and it cannot be turned off. The alarm horn does not work. DTC/fault symptom combinations are found in the comfort system control module. The DTC can be static or sporadic. The wiring harness insulation for the alarm horn can be damaged during the vehicle production assembly. Because the cable is routed through the plenum chamber, water can enter into the cable via the damaged insulation. The water causes the alarm to activate for no reason or it causes the alarm horn to not work.

Voice recognition commands are not recognized or voice recognition accuracy is poor. The location of the microphones within the roof module make them susceptible to interference by the vehicle air vents and climate control settings. When the center air vents are pointed upward, they can cause a "swirling" effect that affects the audio quality of Bluetooth and voice recognition. This is particularly evident on hot days when the A/C system is set to "auto".

When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), the screen freezes briefly. * After the ignition is switched on (shortly after the phone automatically reconnects with the vehicle). * After the phonebook has downloaded. * When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. The command "Call <Name from directory>" is a global MMI command that is available in the telephone menu and main menu screens. If either menu is displayed, the message can appear when the voice recognition button (push to talk) on the steering wheel is pressed.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the programmed Homelink buttons no longer functions. The LED on the Homelink button that is no longer functioning now flashes slowly, indicating that no programming is stored. The customer's transmitter operates at 295Mhz. No DTCs are stored in any control units. At the workshop, the Homelink system can be programmed to the workshop garage door successfully. No trouble is found. The garage door opener control module, J530, was designed with an operational frequency range in which the 295Mhz frequency works correctly during the initial programming of the system. Over time, the transmitting frequency can drift out of range (especially in warmer climates), causing the system to lose its programming.

module, J852, has been calibrated, the windshield has been replaced, or the air suspension level sensors have been adapted. A DTC for incorrect calibration may be stored in the camera control module (address word 85). The camera control module has not been properly calibrated; there is no technical problem.

The alarm horn does not work. TC/fault symptom combinations are found in the comfort system control module, J393 (address word 46). The DTC can be static or sporadic. The wiring harness insulation for the alarm horn can be damaged during the vehicle production assembly. Because the cable is routed through the plenum chamber, water can enter into the cable via the damaged insulation. The water causes the alarm to activate for no reason or it causes the alarm horn to not work.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared.

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. The concern may be more apparent in colder weather, and may improve with warmth or an ignition key cycle. No DTC is stored and no warning appears in the cluster. This PSS TSB applies only to the comfort concern described in the condition of this PSS TSB. Please refer to the attached Information and Q&A document for guidance when handling each case. A solution is in development and will be made available as soon as possible. The steering wheel is mechanically linked to the wheels of the vehicle, and there is no loss of steering functionality. Refer to the attached Information and Q&A document for guidance when handling each case.

The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. The concern may be more apparent in colder weather, and may improve with warmth or an ignition key cycle. No DTC is stored and no warning appears in the cluster. This PSS TSB applies only to the comfort concern described in the condition of this PSS TSB. Please refer to the attached Information and Q&A document for guidance when handling each case. A solution is in development and will be made available as soon as possible. The steering wheel is mechanically linked to the wheels of the vehicle, and there is no loss of steering functionality.

The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. The concern may be more apparent in colder weather, and may improve with warmth or an ignition key cycle. No DTC is stored and no warning appears in the cluster. This PSS TSB applies only to the comfort concern described in the condition of this PSS TSB. Please refer to the attached Information and Q&A document for guidance when handling each case. A solution is in development and will be made available as soon as possible.The steering wheel is mechanically linked to the wheels of the vehicle, and there is no loss of steering functionality. Refer to the attached Information and Q&A document for guidance when handling each case.

The customer states they have a comfort concern about the steering system. The steering works correctly but intermittently feels notchy. There is no loss of steering functionality. The concern may be more apparent in colder weather, and may improve with warmth or an ignition key cycle. No DTC is stored and no warning appears in the cluster. This PSS TSB applies only to the comfort concern described in the condition of this PSS TSB. Please refer to the attached Information and Q&A document for guidance when handling each case.A solution is in development and will be made available as soon as possible. The steering wheel is mechanically linked to the wheels of the vehicle, and there is no loss of steering functionality. Refer to the attached Information and Q&A document for guidance when handling each case.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.

Customer complains of a "popping" noise from the radio followed by 10-15 seconds of no audio. The concern can happen in any audio source. Vehicle is equipped with MMI 3G or MMI 3G+ infotainment systems. Vehicle is not equipped with Bose or Bang & Olufsen sound systems. An ignition cycle is not required for audio to resume.The problem originates in the HD radio code, which can create a "resetting" within the radio unit. Because the tuner is always active in the background, the problem can occur regardless of the audio source or if the HD radio is on or off. It can also occur at any point that the MMI is on, but not necessarily active. For example, the customer opens a door and the MMI starts up. Even though the system is not ?on? because the ignition is not active, the tuner is running and can create the effect.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

The overhead view camera system or one of its cameras does not work. DTCs are logged in the rearview camera system control module. DTCS for the affected camera may also be logged. Incorrect component.

The customer complains that the Audi connect online service in their 2012-2013 A6 or A7 vehicle only reaches 2G service. This bulletin applies only to model year 2012-2013 A6 and A7 vehicles. For other models, see TSB 2039476. This bulletin does not apply to model year 2014 or newer. Starting with model year 2014, the new telephone module was installed in production. Recently, T-Mobile (the service provider for Audi connect) has repurposed some of the GSM spectrum (3G on 2100Mhz band) to maximize 4G LTE coverage in certain metropolitan areas. Devices that do not support 3G service on the 1900MHZ band (including MMI main units of model year 2012-2013 A6 and A7 vehicles) will only receive 2G service when the switch is completed. The change currently only affects the markets listed above, but will affect other markets in coming years. This bulletin will be updated to include these markets as changes occur.

When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver?s voice sounds muffled, as if it is being heard from under water. The microphone seal is damaged during installation into the roof module.

MIL on. DTC P0456 (very small EVAP leak) stored in ECM. No leaks found in the EVAP system. Software update needed.

The driver? s voice is difficult to clearly understand by the caller on the other end of the call when using the Bluetooth hands-free telephone system. The driver? s voice sounds muffled, as if you are hearing them while under water. The microphone seal is damaged during installation in to the roof module.

When pushing the start button, ? Key Not Recognized? shows in the Driver Information Display. No relevant DTCs stored in any modules. Battery voltage of keys used by customer is at or above 3.0V. Concern may or may not be duplicated. A portion of A7 production was built with the incorrect antenna amplifiers in the vehicle, which causes sporadic operation of the keyless remote, espcially when paired with Audi Advanced Key.

Part or all of the daytime running lights do not work on vehicles with LED DRLs. For vehicles with halogen DRLs, please reference TSB 2017488, 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only.

The warning is typically associated with the activation of the static cornering light during low speed turns, or when the turn signal is activated while at a stop. The fault disappears shortly after the cornering light turns off. Entries are logged in J519 (09 ? central electrics unit control unit). Only vehicles with full LED headlights (PR No 8EX or 8EY) are affected. Both headlights remain fully functional during this complaint and still comply with all applicable FMVSS standards. Software within the LED control module incorrectly calculates the current intensity of the headlight LEDs, leading to the DTC.

MIL on with one or more DTCs. DTC P112800 and/or P113000 or P008700 or P244000 and/or P244200 in ECM.

Complaints are reported by the customer regarding electrical features and functions in the vehicle. One or more warning lights on in cluster. The DIS or other displays in cluster are blank. MMI does not function. Windows do not function. LED indicators in various buttons inside the vehicle do not light up. The voltage regulator on the alternator can sporadically fail causing the electrical system to experience too high of voltage. As a result, the affected vehicle electronic components go in to high voltage protection and deactivate sensitive displays and indicators to prevent electrical damage. When an over voltage condition occurs the vehicle electronics and alternator are protected, thus there is no need to replace the entire alternator assembly.

When driving, various warning lights come on, sometimes with restricted functions in the electric system. These complaints only occur together with complaints or a failure of the MMI 3G+ infotainment system. After an ignition cycle the complaint is typically gone; therefore, it may not be reproducible. Sporadic DTCs may be present for communication errors, restricted functions, or missing/incorrect messages. If the MMI 3G+ has an issue, the data bus control unit (Gateway) tries to maintain the communication to the MMI. The load on the unit is so high that other messages on the bus systems cannot be processed any more. As a remedy, modified software can be installed on the Gateway which does not communicate to the MMI 3G+ when it is unavailable.

MMI system randomly freezes and/or resets. DVD Changer playback inoperative after bus sleep (A8 only). HD Radio does not playback in stereo. HD Radio experiences poor blending between digital and analog signals. Google Earth does not properly update the maps after leaving an area of 2G or poor cellular reception. The lower MMI display flickers when an iPod is connected and the Function or Settings menu is selected and the vehicle is stationary. Bluetooth will not automatically reconnect to certain iPhone models after vehicle sleep. Surround settings are lost after ignition cycle (vehicles equipped with BOSE sound systems only). This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). The applicable vehicles can be clearly identified by the SIM card slot on the faceplate of the front MMI mainunit. Continual improvements to MMI software provides solutions to issues experienced in the field.

MIL on. DTC P0456 (very small EVAP leak) stored in ECM. No leaks found in the EVAP system. Software update needed.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

The seatbelt warning light is illuminated, but the passenger seatbelt is buckled. The seatbelt warning chime is not on. This bulletin only applies to vehicles equipped with Radio plus (without Navigation). Software of the instrument cluster control module needs to be updated.

The customer may report that the climate control is sporadically in the ?off? state after the vehicle is restarted, when the climate control was previously ?on? before the ignition was shut off. The climate control unit sporadically does not recognize the ignition cycle change.

The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).

This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.

After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or parameterized via an SVM specified vs. actual comparison (spec/actual). The parameter data in the software coding container has changed for the front and rear door control units. As a result, an SVM code is required to update the parameter data for any replacement control unit. Simply running an SVM spec/actual will not code nor update the parameter data in the new replacement control unit. A hardware change suggestion will be provided when an SVM spec/actual is executed. An additional hardware replacement is not required.

Customer may complain that the seat pneumatics (side bolsters and lumbar support) actuate without any input from the customer. This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D). No leak is present. There is a software issue in the seat pneumatics control modules that causes the seat pneumatics to automatically actuate in high altitudes (change in air pressure) or in fluctuating temperatures in order to maintain pressure.

Audi side assist deactivates or is sporadically inoperative. Message "Side Assist Unavailable" is displayed in the driver information system display when the system deactivates. Audi side assist deactivates or is sporadically inoperative. DTCs are stored in the Lane change assistance control module. A software issue within J769 causes a diagnostic fault, which deactivates the Audi side assist temporarily.

The warning is typically associated with the activation of the static cornering light during low speed turns, or when the turn signal is activated while at a stop. The fault disappears shortly after the cornering light turns off. Entries are logged in the vehicle electrical system control module. Only vehicles with full LED headlights (PR No 8EX or 8EY) are affected. Both headlights remain fully functional and still comply with all applicable FMVSS standards. Software within the LED control module incorrectly calculates the current intensity of the headlight LEDs, which causes the DTC to be set.

When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver's voice sounds muffled, as if it is being heard from under water. The microphone seal was damaged during installation into the roof module.

Customer complains that when the vehicle is driven, various warning lights illuminate, sometimes with restricted functions in the electrical system. The complaint occurs with another complaint regarding the MMI 3G+ infotainment system. After an ignition cycle, the condition is gone and therefore, it may not be reproducible. Sporadic DTCs may be present for communication errors, restricted functions, or missing/incorrect messages.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure.The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged.

Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly.

When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

No DTCs are stored. The keyless remote was not used to unlock the vehicle. In order to minimize current draw after the ignition has been turned off, the electronics system of the vehicle goes into sleep mode. During this time, each module monitors the CAN bus more slowly than when the electronics system is awake. Because the system is being monitored more slowly, there is a delay in the waking of the central locking system. This delay causes a delay in the disabling of the anti-theft alarm system when the manual key is used. If the key is turned in less than a quarter of a second, the system can unlock the vehicle even though the anti-theft alarm has not been disabled.

Customer may report that the head-up display (HUD) flickers or dims quickly. Software in the windshield projection head-up display control module, J898 (address word 82), causes incorrect brightness control.

After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. If the SVM code was not acquired through the GP bulletin in ETKA, follow the instructions in the Service section of this bulletin to update the control module.

The oil pressure switch is defective.

The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared.

When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver?s voice sounds muffled, as if it is being heard from under water. The microphone seal is damaged during installation into the roof module.

Software in the windshield projection head-up display control module, J898 (address word 82), causes incorrect brightness control.

The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the ECM. Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak.

The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.

The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.

The MIL is on. DTC P169A00 is stored in the ECM. The vehicle is in transport mode.

Customer complains that Audi Lane Change Assistant deactivates or is sporadically inoperative. Message ?Side Assist Unavailable? is displayed in the Driver Information Display when the system deactivates. Workshop finds that Audi Lane Change Assistant can be activated without issue. DTCs are stored in the Lane Change Assistance control module. A software issue within J769 causes a diagnostic fault, which deactivates the Audi Lane Change Assistant temporarily.

When the driver uses the Bluetooth hands-free telephone system to make a call, the listener on the other end cannot clearly understand the driver. The driver?s voice sounds muffled, as if it is being heard from under water. The microphone seal is damaged during installation into the roof module.

The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.

This condition can occur when the vehicle is driven at high altitudes or when the outside temperature fluctuates. DTCs may be present in the front seat pneumatics control modules, J873 and J872 (address words 88 and 89) or in the rear seat pneumatics control modules (in certain A8 models only), J875 and J874 (address words 8A and 8D). No leak is present. There is a software issue in the seat pneumatics control modules that causes the seat pneumatics to automatically actuate in high altitudes (change in air pressure) or in fluctuating temperatures in order to maintain pressure.

The seatbelt warning chime is not on. This bulletin only applies to 2012 vehicles equipped with navigation system. Software of the instrument cluster control module needs to be updated.

Audi Lane Change Assistant deactivates or is sporadically inoperative. Message ?Side Assist Unavailable? is displayed in the Driver Information Display when the system deactivates. Audi Lane Change Assistant can be activated without issue. DTCs are stored in the Lane Change Assistance control module. A software issue within J769 causes a diagnostic fault, which deactivates the Audi Lane Change Assistant temporarily.

The driver?s voice sounds muffled or background noise sounds very loud to other caller during Bluetooth calls. Voice recognition commands are not recognized or voice recognition accuracy is poor. The location of the microphones within the roof module make them susceptible to interference by the vehicle air vents and climate control settings. When the center air vents are pointed upward, they can cause a ?swirling? effect that affects the audio quality of Bluetooth and voice recognition. This is particularly evident on hot days when the A/C system is set to ?auto?.

DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails.

The yellow steering symbol is illuminated in the instrument cluster. DTC C10ACF0 (steering end stops not programmed) is logged in the power steering control module, J500 (address word 44). The power steering control module expects to receive a VIN message over the data bus shortly after terminal 15 is turned on. If the VIN message is not received at the expected time, the power steering control module assumes it has been installed in a new vehicle, and it discards the programmed end position values.

slowly.

repair is not needed.

while driving at highway speeds from 55 - 80 mph.

wheel isn't heating evenly.

maneuvered.

outside influence is not covered under warranty.

slowly.

outside influence is not covered under warranty. 2008-2020 A3, 2015-2020 A3 Cabrio, 2005-2016 A3 Sportback, 2005-2020 A4, 2010-2020 A4 allroad, 2005-2012 A4 Avant, 2005-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2005-2020 A6, 2005-2011 A6 Avant, 2008-2020 A7, 2005-2020 A8, 2008-2019 e-tron, 2019-2020 e-tron quattro, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2007-2020 S6, 2008-2020 S7, 2007-2009 S8, 2018-2020 SQ5, 2004-2020 TT Coupe, 2004-2020 TT Roadster, 2012 TT/RS Coupe

Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

slowly.

slowly.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.

Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.

Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

Customer states the vertical adjustment of the steering column does not work or works intermittently. Concern may or may not be duplicated. Software issues causing sporadic failure of the power steering column vertical adjustment.

When making minor steering movements while driving in a straight line in Audi vehicles with electromechanical power steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up. Update the power steering control unit to the latest software.

steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up. This Update is in effect until removed. Procedure is valid only for vehicles that show the 48K8 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. When making minor steering movements while driving in a straight line in Audi vehicles with electromechanical power steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up.

duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

The yellow steering symbol is illuminated in the instrument cluster. DTC C10ACFO (steering end stops not programmed) is logged in the power steering control unit, J500 (44). The power steering control unit, J500 (44), expects to receive a VIN message over the data bus shortly after terminal 15 is turned on. If the VIN message is not received at the expected time, the power steering control unit assumes it has been installed in a new vehicle and discards the programmed end position values.

Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.

Concern may or may not be duplicated. Software issues causing sporadic failure of the power steering column vertical adjustment.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.

The customer may say that the noise is coming from the steering column area, and may describe the sound as buzzing, humming, whistling, whining, grinding, howling, and/or droning. The best way to understand the complaint is to discuss it with the customer. Faulty wheel bearing(s) may cause the noise.

After replacing the electromechanical steering with the control unit J500, the unit cannot be coded via SVM spec/actual.

The yellow steering symbol is illuminated in the instrument cluster. A DTC C10ACFO ? steering end stops not programmed is stored in address word 44 power steering (J500). The steering control unit J500 expects to receive a VIN message over the data bus shortly after terminal 15 is turned on. If the VIN message is not received at the expected time, the J500 assumes it has been installed in a new vehicle and discards the programmed end position values.

The news letter contains information on the Audi TAC hours of operation, the Audi technical assistance survey, the 48K4 update for the power steering control unit J500, meeting the Audi TAC consultants, and information on where to finda ll the editions of the Audi TAC technical newsletter.

The news letter contains information on the Audi TAC hours of operation, the Audi technical assistance survey, the 4.0 L V8 TFSI in the A8L, S6, S7, S8, and the power steering control unit.

Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.

Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.

steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up. This Update is in effect until removed. This Update is in effect until removed. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. When making minor steering movements while driving in a straight line in Audi vehicles with electromechanical power steering manufactured within a specific period, the customer may occasionally perceive slight irregularities with the assistance provided by the power steering. This phenomenon mainly occurs when the temperature is around the freezing point. This is a comfort-related issue; therefore no warning symbol lights up.

Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.

systems control unit, camera(s), LIDAR, and/or sensor(s) which enable automatic emergency braking functionality.

systems control unit, camera(s), LIDAR, and/or sensor(s) which enable automatic emergency braking functionality.

switch; DTC C100C07 and/or C100C29.

(crawling when pulling away or briefly before standstill).

temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.

headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.

Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. This TSB should not be used if another brake noise TSB is available for the vehicle. For additional helpful information, refer to the Audi Brake Systems brochure.

Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.

MMI screen carrier shudders, shakes, and/or is noisy during operation. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). For vehicles with Radio Plus, please follow standard diagnosis steps. The applicable vehicles can be clearly identified by the MMI Touch touchpad on the E380. Incorrect tolerances with the carrier slide mechanism.

DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 (address word 53). According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. Test plan "19-Read Data Bus Keep-Awake Manager", identifies the EPB control module as keeping the data bus active for prolonged periods of time.

Customer may report that the vehicle does not start due to a discharged battery. DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module, J540 (address word 53). According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object. Test plan "19-Read Data Bus Keep-Awake Manager", identifies the EPB control module as keeping the data bus active for prolonged periods of time.

If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.

The message "ACC and braking guard: unavailable at this time. No sensor vision" appears in the instrument cluster. DTC is logged in the distance regulation control module, J428 (address word 13).

DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools.

The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. DO NOT use this TSB if there is another brake noise TSB applicable to the VIN. For additional information, refer to the Audi Brake systems brochure. Brake noise can be attributed to many causes. Brake discs or brake pads are close to or below their wear limit. New brake pads and/or discs have not been properly imbedded after installation. Aftermarket pads or discs are installed. There is debris (such as small stones, grit, road salt, or sand) between brake disc and brake pad. Discs are covered with rust. Rust can form when the vehicle has not been driven for a long period of time. Discs are grooved. There is chemical contamination on the braking surface of the brake disc due to wheel or tire cleaner being sprayed directly onto the brake disc. There are ?pad marks? on the brake disc as a result of brake pad material transferring to the discs. Pad marks can occur when a vehicle has been parked for long periods of time in a wet or snowy environment.

Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.

Cracking or clicking noises from the rear of the vehicle in the C pillar area when driving over bumps or rough roads. The noise comes from the upper shock absorber mounting.

the warning turned OFF after cycling the ignition and there have been no additional occurrences. The customer may state the adaptive cruise control (ACC) was inoperative once, but resumed operating properly after cycling the ignition and there have been no additional occurrences. DTC is stored in the EPB module. Internal code Param_InterFaultID 24 or 25 may be in the extended environmental conditions. The concern is due to a software glitch in the EPB control module. Concerns related to this software glitch can only occur once. Replacing the EPB module may cause an additional occurrence.

Adaptive Cruise Control (ACC) does not work. The message "ACC and braking guard: unavailable at this time. No sensor vision" appears in the instrument cluster. DTC C110BF0 (Adaptive cruise control sensor restricted view) is logged in the distance regulation control module, J428 (address word 13).

The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.

The yellow warning for electromechanical parking brake (EPB) appeared once in the instrument cluster. The warning turned off after the ignition was cycled, and there have not been additional occurrences. EPB function was not affected. The adaptive cruise control (ACC) was inoperative once, but it resumed proper operation after the ignition was cycled, and there have not been additional occurrences. DTCs are logged in the EPB control module.

Oil appears on one or several shock absorbers.

MMI screen carrier shudders, shakes, and/or is noisy during operation. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). For vehicles with Radio Plus, please follow standard diagnosis steps. The applicable vehicles can be clearly identified by the MMI touch interface pad on the control panel. Incorrect tolerances with the carrier slide mechanism can disrupt the travel of the screen.

MMI screen carrier shudders, shakes, and/or is noisy during operation. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). For vehicles with Radio Plus, please follow standard diagnosis steps. The applicable vehicles can be clearly identified by the MMI Touch touchpad on the E380. Incorrect tolerances with the carrier slide mechanism.

DTC U101100 (supply voltage too low) is stored in the gateway, J533 (address word 19), and/or the electronic parking brake (EPB) control module. According to the test plan "19-Read Data Bus Keep-Awake Manager", the EPB control module kept the data bus active for prolonged periods of time. The EPB switch appears to be permanently operating (applying or releasing the parking brake) due to an internal mechanical issue or because it is jammed or blocked by debris or by a foreign object.

The customer may report hearing brake noise from front or rear brakes. The customer may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.

Customer may report hearing brake noise from front or rear brakes. Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.

Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.

Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking. Before proceeding with any of the following steps, check for any applicable TSBs for brake noise. Also refer to the Audi Brake Systems brochure for helpful information.

Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.

MMI screen carrier shudders, shakes, and/or is noisy during operation. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). For vehicles with Radio Plus, please follow standard diagnosis steps. The applicable vehicles can be clearly identified by the MMI Touch touchpad on the E380. Incorrect tolerances with the carrier slide mechanism.

This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.

symbol or emoticon is used in the name field for contact(s).

See owner's manual" is displayed in the instrument cluster without DTCs.

This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.

following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.

Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro

noise.

noise.

navigation.

for a contact name in the MMI address book when a phone is connected to the vehicle via Bluetooth. This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.

The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.

The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.

The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.

MMI 3G+ Sound system "popping" and various other technical Issues (K0715 Update). Only apply this bulletin to vehicles if the customer complaint is in the correct group. Applying the update to vehicles outside of the appropriate group can cause repeat repairs and the warranty claim may be denied. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). The applicable vehicles can be clearly identified by the SIM card slot on the faceplate of the front MMI mainunit.

The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.

The customer may report hearing noises from the upper dashboard area when driving on poor roads, making phone calls, or playing music. The noise can be caused by unfavorable tolerances between the instrument panel speaker and the center speaker trim. A speaker that has been incorrectly installed can make the condition worse. Because there is no attachment to the trim carrier in the speaker cut-out, this area is the likely source of the vibration.

?This service is currently unavailable. Please try again later" message appears in the MMI. The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Replacing the SIM card or MMI hardware or performing the SVM recovery activation will not remedy the concern.

The Bluetooth telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.

While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. The following message appears in the MMI: ?This service is currently unavailable. Please try again later.? The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Additionally, if the vehicle is a model year 2016 A6, A7, or TT, the customer may not be able to see speed and flow traffic information in the navigation map screen, and may consistently see that no traffic reports are available. For these vehicles, traffic is provided by INRIX online.

If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system.

superimposed on the information line of the on-board computer. Incorrect software in the instrument cluster.

This Technical Bulletin provides an overview of HD Radio technology and terminology. The

The customer may report hearing noises from the upper dashboard area when driving on poor roads, making phone calls, or playing music. The noise can be caused by unfavorable tolerances between the instrument panel speaker and the center speaker trim. A speaker that has been incorrectly installed can make the condition worse. Because there is no attachment to the trim carrier in the speaker cut-out, this area is the likely source of the vibration.

The customer may report hearing a rattle sound coming from near the Head Up Display when driving over various road surfaces. The dimensional tolerances of the internal components of the Head Up Display may be in a condition that allows excessive clearance, and the possibility for a rattle noise.

The customer may report hearing a rattle sound coming from near the Heads up Display when driving over various road surfaces. The dimensional tolerances of the internal components of the Heads up Display may be in a condition that allows excessive clearance, and the possibility for a rattle noise.

This Update is in effect until removed. Procedure is valid only for vehicles that show the 58B9 code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. The door seals between the front and rear doors were omitted on Audi A7 vehicles manufactured within a specific period.

The display shows an active data connection, and ? Google? is almost fully white. Customer has active Audi Connect subscription. All other Audi Connect functions operate normally. The concern only occurs if the vehicle is started in a 2G cellular zone. The system operates normally if started in a 3G cellular zone. The vehicle has MMI software 0566 installed. Certain Audi Connect partner carriers are transmitting data that is not supported by the MMI. The data disrupts the loading process of Google Earth and causes it to not completely load.

The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.

Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.

The customer may report hearing noises from the upper dashboard area when driving on poor roads, making phone calls, or playing music. The noise can be caused by unfavorable tolerances between the instrument panel speaker and the center speaker trim. A speaker that has been incorrectly installed can make the condition worse.

Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.

The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system). This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact.

destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi connect. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again in vehicles with Audi connect. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered.

The customer may report hearing noises from the upper dashboard area when driving on poor roads, making phone calls, or playing music. The noise can be caused by unfavorable tolerances between the instrument panel speaker and the center speaker trim. A speaker that has been incorrectly installed can make the condition worse. Because there is no attachment to the trim carrier in the speaker cut-out, this area is the likely source of the vibration.

The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle.

During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.

Bluetooth function of the scan tool must be physically switched off prior to performing this Update. The revised Update will be visible in ElsaWeb and ServiceNet on or about September 27, 2013. Please ensure your technicians are made aware of this new information.

MMI 3G+ Sound system "popping" and various other technical Issues (K0715 Update). This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). The applicable vehicles can be clearly identified by the SIM card slot on the faceplate of the front MMI mainunit.

The Bluetooth telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.

programming function: A software fix is needed to correct the issue: The ODIS Audi Brand update 2.41.1 is setting a ODS5003E error code when you perform the 90TV SVM flash.

decomissioned).

software update for any TSB or Update.

software update for any TSB or Update.

lane assist, DTC B2F0400.

2016-2020 A3, 2016-2020 A3 Cabrio, 2016 A3 Sportback, 2016-2020 A4, 2016-2020 A4 allroad, 2016-2012 A4 Avant, 2016-2020 A5 Cabrio, 2016-2020 A5 Coupe, 2018-2020 A5 Sportback, 2016-2020 A6, 2016-2020 A7, 2016-2020 A8, 2016-2020 e-tron, 2019-2020 e-tron quattro, 2016-2020 Q3, 2016-2020 Q5, 2016-2020 Q7, 2016-2020 Q8, 2016-2020 R8 Coupe, 2016-2020 R8 Spyder, 2017-2019 RS3, 2016-2020 RS5, 2016-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2016-2020 S5 Cabrio, 2016-2020 S5 Coupe, 2018-2020 S5 Sportback, 2016-2020 S6, 2016-2020 S7, 2018-2021 SQ5, 2016-2020 TT Coupe, 2016-2020 TT Roadster

lane assist, DTC B2F0400.

RMC MMI systems.

Customer complains that Audi Side Assist is providing false warnings (no vehicle is present). Concern may or may not be duplicated. No DTCs are present in the Audi Side Assist system. Software fault.

Customer complains that Audi Side Assist is providing false warnings (no vehicle is present). Concern may or may not be duplicated. No DTCs are present in the Audi Side Assist system. Software fault.

Customer complains that Audi Side Assist is providing false warnings (no vehicle is present). Concern may or may not be duplicated. No DTCs are present in the Audi Side Assist system. Software fault.

We have turned off visibility for this Update while an alternate software solution is being developed.

This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.

The most recent calls are not shown in the call lists of the vehicle. Call lists are not shown. The phone book (Directory) in the vehicle is not updated. The phone book is not downloaded to the vehicle. Vehicles with MMI 3G+ are affected.

stored in the TCM.

No faults stored and concern is reproducible.

Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted. Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced.

After ignition cycle, the warning message is no longer present. The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Customer may report transmission warning lamp illuminated in instrument cluster.

This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.

The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

On Audi A6 and A7 vehicles with 8 speed automatic transmissions manufactured within a specific period, problem which affects the shifting comfort may occur in isolated cases. Update the TCM software to the latest level with SVM.

affects the shifting comfort may occur in isolated cases. This Update is in effect until removed. Procedure is valid only for vehicles that show the 37J1 code in the Elsa Campaign/Action Information screen on the day of repair. Vehicle must be within the New Vehicle Limited Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale.

The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.

The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.

Customer may report harsh shift concerns, but the customer is unable to determine the shift point because there is no gear indicator in the cluster. The concern can be reproduced. No faults are stored. TAC must be contacted before any repairs are attempted. Specific information about the concern must be gathered (as described in the Service portion of this bulletin) before TAC is contacted.

The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.

Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.

Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 "Torque Converter Clutch Circuit Performance" or "Stuck Off" is stored in TCM. The fault occurs with ATF temperature below 60o C. Check for this temp range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 "Torque Converter Clutch Circuit Performance" or "Stuck Off" is stored in TCM. The fault occurs with ATF temperature below 60o C. Check for this temp range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module, J217 (03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

The vehicle cannot be started sporadically. The yellow gearbox warning light may be illuminated. Entries are logged in the respected modules. The remote key the customer is using is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle.

The vehicle cannot be started sporadically. The yellow gearbox warning light may be illuminated. DTC's are logged. The remote key the customer is using is transmitting incomplete immobilizer information to the vehicle; resulting in the condition.

Customer may report gearbox warning light on. In some cases after starting vehicle and placing into gear the vehicle would not move. After key cycle the vehicle drives without restriction. The entry P060A00 with DFCC 8692 can be logged in the following situation: After selecting Neutral, a driving mode (D or R) is selected within one second while the vehicle rolls (at under 2 mph). This can, for example, happen when maneuvering the vehicle into or from a parking area. The entry P060A00 with DFCC 8694 can be logged when quickly changing from P-N because of a low diagnosis threshold. The entry P060A00 with DFCC 12480 can be logged because of a low diagnosis threshold when changing gear with the tip function.

Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or ?Stuck Off? is stored in transmission control module (TCM). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

Transmission warning may appear in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or ?Stuck Off? is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o C. Check for this temperature range in the extended environmental conditions of the diagnosis protocol. This TSB only applies if the ATF level is correct and there are no leaks.

The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.

Apple devices with the new 8-pin plug will not play videos using the Audi Music Interface. The current Apple devices have a new plug assignment: the 30-pin plug has been replaced with an 8-pin plug. The old plug used an analog video transmission, whereas the new plug uses a digital video transmission that is not supported by the Audi Music Interface.

The customer complains that the vehicle sporadically cannot be started. The yellow gearbox warning light may be illuminated. DTCs may be present. The remote key being used is transmitting incomplete immobilizer information to the vehicle, resulting in the condition.

dipped beam is switched on.

fender.

the Mirror Server.

weather.

fender.

directed by customer input.

with the remote.

with the remote.

The trunk cannot be unlocked with the button on the remote, with the button in the driver?s door panel, or with the handle on the lid of the trunk. Vehicles have a ?VALET? button in the glove box that activates the valet parking feature, which prevents unauthorized access to the trunk. When the valet parking feature is activated, the trunk can only be opened mechanically with the key.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

An error light for the rear spoiler may be illuminated. The rear spoiler operation can be restricted due to corrosion in the spoiler drive unit. As a result, the rear spoiler becomes stiff and does not reach its end points. This may cause a rear spoiler error light to be illuminated.

The noises are often characterized as a "grinding" sound. The noises arise from the mating surface between the drive cable and the upper pulleys. The noises may be more common in higher temperatures.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the handle is slack.

The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the handle is slack.

The vehicle design in the area around the headlights has a gap that, when the vehicle is washed in car washes having a particular bristle angle and type, can trap these bristles in this area, tear away from the mechanism and lodge in the gap between the headlight and fender.

The door seals between the front and rear doors were omitted on Audi A7 vehicles manufactured within a specific period. The door seals will be installed in the affected vehicles.

The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the handle is slack. When fitting the Bowden cable from the mounting bar to the door lock, the cable can get kinked. In some cases, this can increase the inner friction of the strand in the Bowden cable. As a result, the door lock stays in pressed position or does not completely return to its zero position. When the Bowden cable gets twisted during the installation, the rubber grommets can get distorted. Consequently, the Bowden cable has a too-high inner friction and the door lock does not move to the zero position.

In some scenarios such as extended idling or heavy stop and go traffic, this could cause a slight misinterpretation of the data and possibly an activation of the Malfunction Indicator Light.

taillights.

submissions.

In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.

In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.

In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.

In some scenarios, such as extended idling or heavy stop-and-go traffic, a slight misinterpretation of the data can occur and the MIL may be activated.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

01800, or B126AF0.

S4 Cabriolet, 2008 RS4 Cabriolet, 2010-2021 A4 allroad, 2018-2021 A5 Sportback, 2010-2012, 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2004-2006 A7, 2004-2011 S7, 2021 RS6 Avant, 2004-2006 S8

2015-2021 A3 Cabriolet, 2015-2018 A3 e-tron, 2011-2021 A4 allroad, 2018-2021 A5 Sportback, 2011-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS6 Avant

2015-2021 A3 Cabriolet, 2016-2018 A3 Sportback, 2018-2021 A5 Sportback, 2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 RS 6 Avant

01800, or B126AF0.

14s.

but not overfilled.

The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

Headlight range control inoperative. Xenon high beam shutter inoperative on one side (low beam functioning). Internal fan inoperative. Diagnosis of the concern indicates that the headlight is at fault. Connector in the headlight is not properly seated.

Coolant is leaking from the front intercooler radiator because of stone damage to the radiator. When vehicles are driven on gravel roads, there is a greater chance of front-end stone impact damage to the intercooler radiator.

Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. This is a deliberate design feature designed to avoid injuries in the event of a collision.

Customer may report the license plate attachment screws do not install properly. The license plate brackets are designed to be used with the appropriate length screw installed by hand with a screwdriver. Damaged warranty parts have been returned to Audi of America with evidence of excessive torque used when installing the screw and/or excessive screw length.

Customer states the Homelink controls are pressed into the interior light assembly. Clips holding the Homelink buttons in place are too weak.

MIL on with one or more DTCs. The faults listed can occur under certain driving conditions. This is caused by an incorrect software setting. In some scenarios such as extended idling or heavy stop and go traffic, this could cause a slight misinterpretation of the data and possibly an activation of the Malfunction Indicator Light.

Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.

required" message.

The customer complains that the Audi connect online service in their 2012-2013 A6 or A7 vehicle only reaches 2G service when in metropolitan areas. This bulletin applies only to model year 2012-2013 A6 and A7 vehicles. For other vehicles, see TSB 2039476.

Instructions for vehicle inspection, protection removal, and detailing.

CD or DVD disks do not automatically change from one to the next in the external CD or DVD changer.

This TSB contains information on technician preparation when calling the Audi Technical Assistance Center

Oil filter cartridge requires replacement.

Instructions for vehicle inspection, protection removal, and detailing.

Instructions for vehicle inspection, protection removal, and detailing.

VIN plate and/or B-Pillar Safety Certification label requires replacement.

Technician preparation when calling the Audi Technical Assistance Center (TAC).

A squealing, howling, or whistling noise may be heard coming from under the vehicle. The condition is typically noticed when the vehicle is cold and is moving at speeds of 5 - 60 mph. The noise is from the intermediate bearing of the propeller shaft.

Leather upholstery is dirty or stained.

Cruise control deactivates sporadically or cannot be activated. A new set speed cannot be saved. ?Set? button on cruise control stalk does not work. DTCs are present in the vehicle. Incorrect tolerances of cruise control ?Set? button.

Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options.

Instructions for vehicle inspection, protection removal, and detailing.

State of Minnesota.

Software update needed.

conditions.

Media files can now be viewed on any smartphone or tablet.

Software update needed.

conditions.

Media files can now be viewed on any smartphone or tablet.

Software update needed.

conditions.

Media files can now be viewed on any smartphone or tablet.

some issues.

new kit if the correct DTC and symptom code combination is present.

new kit if the correct DTC and symptom code combination is present.

new kit if the correct DTC and symptom code combination is present.

new kit if the correct DTC and symptom code combination is present.

Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.

The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.

The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.

Moisture in the driver or front passenger foot well. Due to a faulty and/or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose.

concern.

the concern.

concern.

of the concern.

from the HVAC system.

2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster

a ODIS GFF test plan.

Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.

The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.

This bulletin applies to any repair that requires replacement of the air conditioning compressor. Any replacement of A/C compressors?regardless of the reason for failure?must include an ODIS GFF cooling performance test plan of the A/C system with documentation of the recovered refrigerant volume. This GFF test plan requirement is mandatory without exception.

When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.

Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.

2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and 2018-2020 RS5 Cabriolet, 2018-2020 S5 Sportback, 2008 A7, 2008-2011 S7

Wheel bolt requires torque adjustment.

Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.

C104311.

The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.

The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.

airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.

replacement airbag inflators that are being installed in used vehicles.

airbag/seatbelt is deployed/not deployed; general accident information; and fire and overheat damage.

(airbag/seatbelts, accidents, fire and overheat damage).

(airbag/seatbelts, accidents, fire and overheat damage.

(airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe