2010 Audi A6 TSBs

not activate.

mode.

not activate.

Assistnce Center (TAC).

(TAC).

(Ghost faults).

whining, or similar interference.

No DTCs are stored.

crankcase pressure can lead to the above described DTC codes.

to appear.

crankcase pressure can lead to the above described DTC codes.

to appear.

crankcase pressure can lead to the above described DTC codes.

to appear.

system.

restriction.

exist or it is inoperative/constant warning.

restriction.

exist or it is inoperative/constant warning.

exist or it is inoperative/constant warning.

restriction.

restriction.

restriction.

restriction.

restriction.

exist or it is inoperative/constant warning.

Includes A3 Cabriolet 2015-2020, 2010-2020 A4 Allroad, 2018-2020 A5 Sportback, RS5 Cabriolet 2010-2012 and 2018-2020, 2018-2020 S5 Sportback, 2010-2011 S7, 2010 S8, 2019-2020 e-tron Quattro.

2005-2019 A3, 1996-2019 A4, 2008-2019 A5, 1992-2019 A6, 2012-2019 A7, 1997-2019 A8, 2019 E-Tron, 2015-2019 Q3, 2010-2019 Q5, 2007-2019 Q7, 2019 Q8, 2000-2019 TT, 2008-2018 R8

restriction.

2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster

2008-2020 A3, 2015-2020 A3 Cabrio, 2008-2016 A3 Sportback, 2008-2020 A4, 2010-2020 A4 allroad, 2008-2012 A4 Avant, 2008-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2008-2020 A6, 2008-2011 A6 Avant, 2008-2020 A7, 2008-2020 A8, 2008-2019 e-tron, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2008-2012 S4, 2008-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2008-2020 S6, 2008-2020 S7, 2008-2009 S8, 2018-2021 SQ5, 2008-2020 TT Coupe, 2008-2020 TT Roadster, 2012 TT/RS Coupe

restriction.

restriction.

numbers going forward.

restriction.

restriction.

restriction.

restriction.

change.

This is for all keys and there is no relevant DTCs stored.

restriction.

restriction.

restriction.

exist or it is inoperative/constant warning.

This notice contains information for the accessories operations technical bulletin.

restriction.

restriction.

MODELS 2009-2011 A6. *PE

stored in the ECM P030000.

brakes.

working; mileage below 50 km/32 miles.

working; mileage below 50 km/32 miles.

interrupted when the following DTC? s are present in the engine control module:

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

a restriction.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

a restriction.

a restriction.

Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

a restriction.

crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

that the oil level is not okay.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

a restriction.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

a restriction.

a restriction.

Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

a restriction.

crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

that the oil level is not okay.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

a restriction.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

a restriction.

a restriction.

Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

a restriction.

crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

that the oil level is not okay.

The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

The leak can be traced to the connection of the water pump and the hose leading to the heater core (Figure 1). The seal ring is not the cause of the leak.

available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures.

consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

When changing the oil filter and installing the new filter seal(s) in the oil filter housing, special attention is required.

consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner? s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods.

a restriction.

The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

a restriction.

Drop in fuel pressure may cause delayed restart of the engine (?long crank?) and/or rough idle after startup.

The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.

sent Takata airbag recall reminder notices to approximately 565 Audi owners in the State of Puerto Rico on July 25, 2022.

sent Takata airbag recall reminder notices to approximately 2,616 Audi owners in the State of Georgia on June 22, 2022.

The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.

to approximately 12,349 Audi owners in the State of California on April 29, 2022.

Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off).

Drivers who consciously or unconsciously drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system software. As a result, application of the brake and accelerator pedals at the same time (brake pedal with left foot and accelerator pedal with right foot) results in the following: ? Brake pedal function (normal at all times) overrides any throttle application. ? Diagnostic Trouble Codes (DTCs) will not be stored. ? When the brake pedal is applied while the accelerator is depressed, engine RPMs will return to idle speeds of 1400 RPMs after approximately two seconds. ? When the accelerator is applied while the brake pedal is depressed, the vehicle accelerates slower than usual (reduced engine torque).

When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.

of Highway Safety and Motor Vehicles, Audi will be sending Takata airbag recall reminder notices to approximately 10,000 Audi owners in the state of Florida on October 14, 2019. 2005 A4 Avant, S4 Avant, 2006 A4 Avant, A6 Avant, S4 Avant, 2007 A4 Avant, A6 Avant, S4 Avant, S4 Cabriolet, 2008 A4 Avant, A6 Avant, RS4 Cabriolet, S4 Avant, S4 Cabriolet, 2009 A6 Avant, 2010 A6 Avant, 2011 A6 Avant, 2016 TT Roadster, 2017 R8 Spyder, TT Roadster.

Audi will be sending Takata airbag recall reminder notices to approximately 2,877 Audi owners in the state of Wisconsin on July 8, 2019. (2005) A6 SEDAN, A4 SEDAN, A4 AVANT, S4 SEDAN, S4 AVANT, (2006) A3, A6 SEDAN, A6 AVANT, A4 SEDAN, A4 AVANT, S4 AVANT, S4 SEDAN (2007) A3, A4 Cabriolet, S4 Cabriolet, A6 SEDAN, A6 Avant, S6 SEDAN, A4 SEDAN, A4 Avant, S4 Sedan, S4 Avant, A4 Cabriolet, RS4 Sedan, S4 Cabriolet, (2008) A3, A4 Cabriolet, S4 Cabriolet, A6 Sedan, A6 Avant, S6 Sedan, A4 Sedan, A4 Avant, S4 Avant, S4 Sedan, A4 Cabriolet, RS4 Sedan, RS4 Cabriolet, S4 Cabriolet, (2009) A3, Audi Q5, A4 Cabriolet, S4 Cabriolet, A6 Sedan, A6 Avant, S6 Sedan, A4 Cabriolet, S4 Cabriolet (2010) Audi Q5, A3, A5 Cabriolet, A6 AVANT, A6, S5 Cabriolet, S6 (2011) Audi Q5, A3, A5 Cabriolet, A6 AVANT, S5 Cabriolet, S6 (2012) Audi Q5, A5 Cabriolet, S5 Cabriolet, A3 (2013) A3 (2016) TT COUPE, TT ROADSTER (2017) TT COUPE, TT ROADSTER, R8 COUPE, R8 SPYDER

recall reminder notices to approximately 15,000 Audi owners in the State of New York on May 23, 2019. This document also applies to the 2007-2008 S4 Cabriolet, 2005-2008 S4 Avant, 2005-2008 A4 Avant, 2006-2011 A6 Avant, 2016-2017 Roadster, 2017 R8 Spyder.

The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.

Clutch is not operating properly. Clutch has a burnt smell. Clutch pedal does not fully return to starting position. Incorrect shifting, the revolutions of clutch plate and engine input shaft differ too much, excessive slipping of the clutch, and when the clutch is pressed and an incorrect lower gear is selected, can result in clutch damage.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.

MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

The coolant level warning is not on. A minor coolant leak is possible during the break-in phase of the coolant seal on the coolant pump. The dry coolant marks are normal.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (address word 01), is storing one or more engine misfire fault codes. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.

All systems on Audi vehicles are engineered to work together using the factory calibrations, which have been extensively tested and validated before the vehicle is released for sale. The Audi warranty coverage is based on the results of developing the vehicle under the factory calibration. If a vehicle is equipped with unauthorized hardware or software tuning, it can cause stress on vehicle components outside of intended design limits, and can cause damage and additional wear. Subsequently, factory powertrain warranty coverage is reduced or voided.

MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

MIL on. DTCs for air-fuel ratio imbalance are stored in the engine control module (ECM). An incorrect software setting causes the DTC to be stored.

MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

Electric steering column adjustment is restricted or does not work at all. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. The seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, so the electric steering column adjustment fails.

cover cleaning of the engine cylinder head secondary air ports to remove carbon buildup under specific conditions to 10 years or 120,000 miles, whichever occurs first, from the vehicle's original in-service date for certain 2009-12 Model Year Audi vehicles with 3.2L engine, and certain 2009-2013 Model Year Audi vehicles with 3.0T engines. The vehicle's original in-service date is defined as the date the vehicle was delivered to either the original purchaser or the original lessee; or if the vehicle was first placed in service as a "demonstrator" or "company" car, on the date such vehicle was first placed in service. The warranty extension is fully transferable to subsequent owners. Audi has determined that under certain driving conditions, carbon buildup can occur in the engine cylinder head secondary airports. Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of the on-board diagnostic system. In some locales, an illuminated MIL could cause the vehicle to fail an IM emissions inspection, vehicle registration application could be denied. Audi will diagnose, and if necessary clean the engine cylinder head secondary air ports to remove the carbon buildup at no cost to the customer as long as the vehicle is within the time and mileage limits of the warranty extension. This warranty extension covers only the diagnosis and cleaning of the cylinder head secondary air ports to remove the carbon buildup. Reimbursement is applicable only to the repairs described in this Warranty Bulletin.

Due to the presence of specific fault codes caused by this carbon buildup, the Malfunction Indicator Lamp (MIL) on the instrument cluster may illuminate. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL. In some locales, an illuminated Malfunction Indicator Lamp could cause your vehicle to fail an IM emissions inspection, and your vehicle registration application could be denied. Please be aware that other conditions (unrelated to the issue described in this letter) may cause the MIL in your vehicle to illuminate. Customers should be prepared to cover all diagnosis and repair costs for these other, unrelated conditions.

Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

We have identified the radiator mountings installed in production as the cause of these small leaks.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.

Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Muh? sound or moaning noise coming from the front brakes (FNRG). The performance of the brakes is not compromised. The pistons in the calipers in certain vehicles may not retract far enough, which may leave contact between the rotor and pad. This contact may cause a ?muh? sound or moaning noise in low speed conditions.

stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine.

Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

The engine judders or runs erratically. The vehicle judders during acceleration. No event entry is stored in the engine control module (ECM). The air mass meter is suspected to be faulty. Possible incorrect function on the sensor elements of the air mass meter.

Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.

Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

Under extreme driving conditions, such as a driving profile of mainly short distance (stop and go) driving high crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner? s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods.

Poor performance. Unnecessary High Pressure Fuel Pumps replacement due to Guided Fault Finding test plans not being performed or interrupted when the following DTC?s are present in the engine control module.

Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods.

After the activation of the cam actuator to change to the other cam profile, the pin of the actuator is pushed back in by the cam. This is confirmed by a voltage impulse, which is registered by the engine control unit and confirms the operation. If this does not happen, or not at the right time, a DTC "implausible signal" is saved in ECM memory. Check the distance of the pin tip of the cam actuator for valve lift system to the camshaft when it is not operated with a gauge. The measurement of the tip to the basic camshaft circle outside of the groove must be taken. If this measurement is 0.9mm, the actuator 06E103697J must be installed. The actuator 06E103697J must only be used, if the measurement is 0.9mm or bigger.

Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens. Damp air settles on the inside of a cold lens, which creates condensation. The headlight circulation system allows air from the outside to flow through the headlights. This open waterprotected ventilation system (needed for pressure compensation) creates different climate zones in the headlight: very warm areas, where the lens is warmed up by the light, and relatively cool areas, where the lens is cooled own by the air flow. Considerable differences in humidity and temperature between the inside and the outside of the headlights, even while driving, can lead to condensation. This is especially true in cold and wet weather, but it can also happen after a car wash, after steam cleaning the engine or the front end, with overnight temperature changes, etc. This phenomenon is more visible on lenses made of clear glass than on lenses with patterns. The moisture does not affect the headlight function (light performance) and does not lead to corrosion or other damage to headlight parts.

MIL on, with DTCs stored in the 01 (Engine Control Module). Under extreme driving conditions, such as a driving profile of mainly short distance (stop and go) driving high crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure.

Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner? s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods.

To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4 F (2 C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc.

Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition.

Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.

Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment.

Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.

The MIL is on. DTCs are stored in the ECM. Under extreme driving conditions (such as short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.

Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise. Diesel fuel requires additive blending or ?winterization? to be useable at low temperatures. At temperatures below 20 F (-7 C), No. 2 Diesel with insufficient winterization blending may lose its fluidity due to wax separation. This may clog the fuel filter or in-tank filter, preventing the engine from operating properly. No. 2 Diesel is blended by refineries to various levels of winterization (minimum useable temperature) based on month, geographical location, and the 10th percentile minimum ambient air temperature for the given region. Although rare, during sudden periods of extreme low temperatures (record lows), fuel stations may not be adequately prepared with No. 2 Diesel fuel with sufficient winterization to resist wax formation or ?gelling?.

There are 79,232 Audi vehicles affected in the U.S. by this Update. Rough idle or reduced driving power and, in turn, an illuminated Malfunction Indicator Lamp (MIL) on the instrument cluster due to the presence of specific fault codes caused by this component. Inspect and replace ignition coils as required.

Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

During reset of the service reminder, the message ?AIR system - action required - observe test plan? appears on the ODIS tester. MIL is not illuminated. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

MIL on. DTCs are stored in the engine control module (ECM). Under extreme driving conditions (such short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure.

Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.

Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed.

Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods.

MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.

MIL is not illuminated. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. The ODIS tester can identify the state of the restriction, and will request that the system is cleaned in order to prevent the MIL from illuminating.

A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual.

Customer complains of excessive oil consumption. Production solution is Crankcase pressure reduction starting with model year 2013.

Noises and inconsistent engine operation after cold start during the catalyst heating phase. The customer may misinterpret these symptoms as engine misfiring. This bulletin applies only to non-diesel engines.

Customer complains of excessive oil consumption. Crankcase pressure reduction starting with model year 2013.

There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor. If the odor is noticeable in the vehicle when the engine is not turned on, the cause may be mold and mildew in the passenger compartment, and not be related to the A/C system. All other possible sources of the odor must be investigated before this bulletin can be performed.

A delay and shudder is felt when vehicle is driven from a stop. Shuddering is felt on acceleration from under 15 mph. The complaint can be reproduced, but no fault can be found. Incorrect calibration of the engine control module (ECM), J623 (address word 01) and of the transmission control module (TCM), J217 (address word 02).

In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions.

This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).

Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.

The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.

J623 (address word 01): DTC P219C00 (stored in cylinder 1), DTC P219D00 (stored in cylinder 2), DTC P219E00 (stored in cylinder 3), DTC P219F00 (stored in cylinder 4), DTC P21A000 (stored in cylinder 5), DTC P21A100 (stored in cylinder 6). An incorrect software setting causes the DTC to be stored. TSB 2011732 00 Software Version Management (SVM), operating instructions will be necessary to complete this procedure.

NEEDED.

NEEDED.

CYLINDER HEAD.

CYLINDER HEAD.

NEEDED.

ELEMENT FOR CAMSHAFT ADJUSTMENT VALVE CAN LOOSEN AND IN OIL CIRCUIT, THERE IS NO DAMAGE FROM LOOSENED PARTICLES. MODEL ALL. ALL YEARS. *PE

A WARRANTY EXTENSION HAS BEEN ISSUED FOR 10 YRS OR 120, 000 MILES, WHICHEVER OCCUR FIRST, ON EMISSIONS CONTROL SYSTEMS WARRANTY FOR INTAKE MANIFOLD AND FUEL INJECTORS, UNDER SPECIFIC CONDITIONS. MODEL 2008-2011. *PE

(MIL) ON INSTRUMENT PANEL DUE TO SPECIFIC FAULT CODES PRESENCE. MODEL 2010-2013 A4, A5, A6, Q5. *PE

INFORMATION PROVIDED REGARDING WARRANTY EXTENSION ON CARBON BUILDUP REMOVAL, ENGINE CYLINDER HEAD SECONDARY AIR PORTS. MODELS 2009-2012. NO MODEL PROVIDED. *PE

ENGINE AREA AND SEAL RING IS NOT THE CAUSE. MODEL 2009-2013 A4, A5, Q5, A6. *PE

CRANKCASE PRESSURE CAN BE LOWERED WITH NEW ECM (ENGINE CONTROL MODULE) SOFTWARE LEVEL AFTER CHANGING CRANKCASE PRESSURE VALVE TO IMPROVE AND ELIMINATE MENTIONED DTC CODES. MODELS 2010-2012 S4, S5, 2009-2011 A6 (C6), 2011-2012 Q7, 2012 A6, A7. *PE

MOVE SHIFTER; ENGINE SWITCHED OFF BUT REMOTE CONTROL CAN NOT LOCK WITH ADVANCED KEY; PARK IS NOT RECOGNIZED ELECTRICALLY. *PE

THE ENGINE THERMOSTAT STAYS CLOSE AND MAY CAUSE THE ENGINE TO OVERHEAT. WARNING LIGHTS WILL ILLUMINATE. 2010-2011 MODELS. *RM

A SEAL INSIDE THE COOLANT PUMP CAN WEAR OUT AND LEAK COOLANT. THIS ALSO CAUSED THE ENGINE LIGHT TO COME ON. *RM UPDATED ON 06/27/2011. *KB

*RM

1 MISFIRE DETECTED-CYL.12 MISFIRE DETECTED); ENGINE MAY HAVE REDUCED PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. *PE

1 MISFIRE DETECTED-CYL. 12 MISFIRE DETECTED); ENGINE MAY HAVE REDUCED PERFORMANCE WITHOUT SIGNIFICANT LOSS OF POWER OR STALLING. *PE

THE SOFTWARE IN AIRBAG CONTROL MODULE IS TOO SENSITIVE (ONLY AT ENGINE STARTUP) WHEN DIAGNOSING THE SIDE CRASH SENSORS. AS A RESULT, THE AIRBAG CONTROL MODULE CAN INCORRECTLY SET FALSE DTCS FOR CRASH SENSOR INCORRECT. THE SOFTWARE IN THE AIRBAG CONTROL MODULE MUST BE UPDATED TO REPAIR THIS CONDITION. *PE

SELF LEVELING SYSTEM CANNOT BE ADJUSTED ANY MORE WITH THE MMI; COMPRESSOR FOR SELF LEVELING SYSTEM CONTINUES TO RUN AFTER SWITCHING OFF THE ENGINE AND LOCKING THE VEHICLE. BECAUSE OF POOR PERFORMANCE OR FAILURE OF COMPRESSOR FOR AIR SUSPENSION, VEHICLE POSITION CANNOT BE ADJUSTED. *PE

programming function: The hotfix is to correct the issue: Issue seen: ODS5003E Infrastructure Guided Fault Finding: An internal fatal error occurred during the G929 - Vehicle Interior Carbon Dioxide Concentration Sensor function test plan. NOTE: This ODS error could show up on any other GFF function test plans as well.

range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. ? The displayed vehicle range drops inconsistently. ? After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. ? When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. ? There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

verification steps to ensure that the vehicle is configured correctly. For additional information on known current draw issues, refer to the following TSBs: ? 2014127: 27 Battery dead or low after returning to the vehicle (2007 A6, A8, Q7) ? 2019143: 27 Battery discharged on some vehicles with Advanced Key (2005 - 2008 A6, Q7)

Then, every 40,000 miles or 3 years, whichever occurs first: Added: TTS 2.0L TFSI

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

high voltage vehicles (Hybrid, Plugin Hybrid, Electric Vehicle), the Volkswagen Tools and Equipment Team has identified two US based suppliers to support dealers in USA and Canada.

disconnected or replaced.

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition.

The washer solvent level warning is on in the DIS, but the washer solvent level is correct. There is no functional restriction in the windshield washer system. The sensitivity of the washer solvent level sensor (G33) can be affected by the type, concentration, and the presence of additives in the washer solvent currently in the tank. The operation of the level sensor relies on the composition of the solvent to provide an accurate message on the solvent level. Incorrect concentration and the presence of additives can contaminate the sensor and reduce its sensitivity.

The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". The lock command history is stored in the convenience system control module (J393).

Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

When a phonebook with a large number of contacts is being downloaded, the MMI screen freezes in one of the following scenarios: * After the initial Bluetooth connection (shortly after the phone is bonded to the vehicle), the screen freezes briefly. * After the ignition is switched on (shortly after the phone automatically reconnects with the vehicle). * After the phonebook has downloaded. * When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. The command "Call <Name from directory>" is a global MMI command that is available in the telephone menu and main menu screens. If either menu is displayed, the message can appear when the voice recognition button (push to talk) on the steering wheel is pressed.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the programmed Homelink buttons no longer functions. The LED on the Homelink button that is no longer functioning now flashes slowly, indicating that no programming is stored. The customer's transmitter operates at 295Mhz. No DTCs are stored in any control units. At the workshop, the Homelink system can be programmed to the workshop garage door successfully. No trouble is found. The garage door opener control module, J530, was designed with an operational frequency range in which the 295Mhz frequency works correctly during the initial programming of the system. Over time, the transmitting frequency can drift out of range (especially in warmer climates), causing the system to lose its programming.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders.

The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal.

When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C Pressure/Temperature Sensor G395 leaks refrigerant. This causes Sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the J519 Central Electrics Control unit to Sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of Vehicle Electrical System Control Module J519. Vehicle Electrical System Control Module J519 transfers the information provided by the sensor via the comfort data bus to Climate Control Module J255.

The MMI displays that the memory function is not active. The seat memory control unit can be deactivated due to voltage fluctuations in the vehicle? s power system, or from a large static discharge through the seat cover. If the seat memory control unit is deactivated due to the above mentioned influences, the control unit cannot be reactivated through any vehicle controls, vehicle keys, or through the normal GFF test plans. It can only be reactivated with special test plans within the tester.

Customer may complain that the vehicle locks itself when removing the key from the ignition lock. When removing the ignition key from the ignition, the customer may unintentionally operate the lock button of the remote key. With the S contact in the ignition lock off (key is removed), the central locking will resume to respond to signals from the remote key. MVB 17 in electric control unit address $46 (Comfort System Central Control Module) can be used for argumentation. The last received central locking command is stored in this MVB. A value of ?2? indicates a locking command last sent from the remote key. With the Autolock feature, MVB 17 is overwritten. Therefore MVB 17 must be read immediately after the complaint.

Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.

Warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 / 14 (Control unit faulty) is registered in the dynamic headlight range control unit, address word 55. Both headlights function normally. Vehicles equipped with adaptive (cornering) lighting. New software version 0010 in the dynamic headlight range control module addresses this condition. If the headlight range control module has a software version lower than 0010 installed, then use the SVM code listed in Service to update the module. Some control units will already have software version 0010 installed but can still exhibit the conditions mentioned above. When this occurs, the software will need to be reflashed using a separate SVM code. The corrupt software will be overwritten. The software version does not change after the update.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).

This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.

The seat memory does not work. The MMI displays a message that the memory function is not active. The seat memory control unit can be deactivated due to voltage fluctuations in the vehicle?s power system, or from a large static discharge through the seat cover. If the seat memory control unit is deactivated due to either of these influences, the control unit cannot be reactivated through any vehicle controls, vehicle keys, or through the normal GFF test plans. It can only be reactivated with special test plans within the tester.

Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure.The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged.

Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly.

When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer.

The warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 - 14 is stored in the headlamp range control module, J431 (address word 55). Both headlights function normally. The vehicle is equipped with adaptive (cornering) lighting. There is a software issue in the dynamic headlight range control module.

After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. If the SVM code was not acquired through the GP bulletin in ETKA, follow the instructions in the Service section of this bulletin to update the control module.

The MIL is on. DTC may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.

The MIL is on. DTC P0087 may be stored in the ECM. Drivability concerns such as hard starting/no starting are present. Outside temperature is sub-freezing. In tank, fuel pump may be making a straining noise.

The navigation DVD or other CD/DVD cannot be ejected. There are no DTCs stored in the corresponding module. The eject button is not stuck. When the eject button is pushed, the drive does not sound as if it is trying to eject the CD/DVD. Vehicles with DVD-based navigation systems now have the navigation DVD installed during production. To prevent theft of the DVD during transportation, the eject button of the navigation drive is disabled. The navigation system itself (e.g., route guidance) functions as specified. The eject buttons of vehicles without DVD-based navigation systems are not disabled during production, but could behave as described in the Condition section of this bulletin. The eject button can be enabled through Guided Fault Finding.

The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).

The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start.

Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices.

Sporadic fault memory entries are stored in various control modules. Contacts may be widened (over 0.63 mm) if incorrect pins or incorrect methods for current flow tests are used. Either action may cause intermittent electrical connections, which can cause sporadic DTCs to be stored in various control modules.

Part or all of the daytime running lights do not work on vehicles equipped with LED daytime running lights. For vehicles with halogen daytime running lights, refer to TSB 2017488: 94 Halogen Daytime running lights do not work. In the past, the daytime running light bulbs were a serviceable part. In this application, the LED strip cannot be replaced, and may have an associated control module. This TSB is for servicing information only.

Bluetooth connection (shortly after the phone is bonded to the vehicle), after the ignition is switched on (shortly after the phone automatically reconnects with the vehicle), and after the phonebook has downloaded. When the voice recognition system is used, a message appears in the MMI screen stating that the phone book is too large and that the voice recognition system cannot be used. When music is streamed to the MMI system with the Bluetooth A2DP connection, the music intermittently pauses or seems to skip. The condition goes away once the phonebook transfer is completed. The MMI uses a limited portion of the total memory to convert the name and phone number fields of downloaded contacts into a voice command (text to speech). Extensive processing takes place if too many letters are used in the first and last name fields or if numbers or special characters are entered. The remaining memory is dynamically assigned to different applications which can also affect the capacity of the voice command processing. The MMI does not respond until the process is completed or it may freeze if phonebook fields are too large or do not follow typical formatting. In addition, the text-to-speech capacity is exceeded and the voice recognition system is rendered inactive.

DTC 00456 (Access/start control module -J518- no communication) is found in several control modules or the access/start authorization control module, J518 (address word 05), identifies itself with implausible data can be found through guided fault finding (GFF). If no communication is possible, activate the bus by switching on the hazard warning lights. It should now be possible to carry out a diagnosis. If DTC 00288 (Steering column lock actuator-N360, faulty) is logged in the access/start authorization control module, J518 (address word 05), this bulletin does not apply. Proceed according to GFF. Incorrect software.

below threshold) being stored in the ECM. New ECM software implemented to correct the condition.

DUE TO MODULE CROSS CARRIER AND UNFAVORABLE TOLERANCES TO STEERING COLUMN. MODEL 2003-2010 A8, 2005-2011 A6, 2007-2014 Q7. *PE

*PE

SOFTWARE UPDATE NEEDED. *JS

WHEN REMOVING THE IGNITION KEY FROM THE IGNITION, THE CUSTOMER MAY UNINTENTIONALLY OPERATE THE LOCK BUTTON OF THE REMOTE KEY. WITH THE S CONTACT IN THE IGNITION LOCK OFF, THE CENTRAL LOCKING RESPONDS TO SIGNALS FROM THE REMOTE KEY. *PE

THIS CONDITION CAN BE CREATED BY LOW BATTERY VOLTAGE IN THE VEHICLE. THE DTCS ARE INCORRECTLY SET IN THE DIAGNOSIS PROTOCOL OF THE AIRBAG CONTROL UNIT. THESE DTCS DO NOT AFFECT THE FUNCTIONALITY OF THE AIRBAG SYSTEM. IMPROVED AIRBAG CONTROL SOFTWARE IS PLANNED FOR PRODUCTION. *PE

HEADLIGHT TURNS ON OR OFF EARLY OR LATE WHEN THE LIGHT WITCH IS IN THE AUTO POSITION; AFTER REPLACING THE RAIN LIGHT SENSOR G397 OR AFTER REPLACING THE WINDSHIELD, THE AUTOMATIC HEADLIGHT MAY TURN OR OFF WITHOUT CHANGE OF AMBIENT BRIGHTNESS. HEADLIGHTS OPERATE NORMALLY IF THE LIGHT SWITCH IS IN THE ON OR OFF POSITION. *PE

REGULATION, FUEL PRESSURE OUTSIDE TOLERANCE); P129F OR P008B (LOW PRESSURE FUEL SYSTEM, PRESSURE TOO HIGH); P129F OR P008A (LOW PRESSURE FUEL SYSTEM, PRESSURE TOO LOW); P2540 (LOW PRESSURE FUEL SYSTEM, PRESSURE OUT OF RANGE; AND P0087 (RAIL FUEL PRESSURE SYSTEM, PRESSURE TOO LOW). *PE

SVM IS A PROCESS TO UPDATE THE PROGRAMMING IN FLASHABLE (RE-PROGRAMMABLE) CONTROL MODULES AND/OR TO DOCUMENT CHANGES IN SOFTWARE LEVELS IN AUDI VEHICLES. THIS SYSTEM USES THE VAS 5051B OR VAS 5052 DIAGNOSTIC TOOLS TO SEND VEHICLE SPECIFIC DATA TO THE SVM DATABASE, TO DOWNLOAD INSTRUCTIONS FROM THE SVM DATABASE, AND TO FLASH CONTROL UNITS FOR IDENTIFIED SOFTWARE UPDATES. *PE

symbol or emoticon is used in the name field for contact(s).

See owner's manual" is displayed in the instrument cluster without DTCs.

This update to Elsa2Go ensures that both systems are displaying the same campaign information, including OPEN/CLOSED status, repair date as well as criterions at the same time without any discrepancy.

following conditions occurs when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system): *The MMI screen goes blank then restarts. *The MMI screen freezes for a few minutes then recovers.

Also A3 Cabriolet 2015-2021, A3 Sportback 2016-2018, 2005 A4 Cabriolet , 2005-2009 S4 Cabriolet, 2010-2012 and 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2021 S6, 2005 and 2006 A7, 2005-2011 and 2021 S7 2005-2006 and 2021 S8, 2019-2021 E-Tron Quattro

navigation.

The ?Device or cable type not supported? message may be displayed when the wrong AMI cable type is used. See the Service section of this bulletin for an overview of the AMI cables that support iOS devices.

The customer would like to add a different navigation map database for countries outside of the USA or Canada. The customer would like to change the MMI system language to a different language that is not already supported by MMI. When a song is being played and the track information for that song contains foreign language characters, the driver information system (DIS) in the cluster correctly displays the characters, but the MMI display does not.

The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. The vehicle is equipped with RNS-E, Concert Radio with SD card slot, MMI3G, MMI3G+, or MIB.

No audio from all audio sources (for vehicles with base sound system) or no audio from AM, FM, and satellite radio (for vehicles with Bose or Bang & Olufsen sound system). This TSB does not apply to vehicles with a separate amplifier and the complaint "no audio from all audio sources." Bluetooth is inoperative or loses connection. Bluetooth phone does not download contacts and/or call stacks. Satellite radio band is not available in band selection screen. Satellite radio presets sporadically disappear. When starting the 3G MMI system, the start screen does not appear and only the time is shown. This bulletin only applies to vehicles with Navigation Plus (PR Number 8DY). The applicable vehicles can be clearly identified by the controller located in the center console. Continual improvements to MMI software provides solutions to issues experienced in the field.

The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding.

The Bluetooth telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.

If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system.

This Technical Bulletin provides an overview of HD Radio technology and terminology. The

The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.

The MMI control knob joystick is loose or has fallen off. Only vehicles with navigation and without MMI touch are affected.

The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding.

Customer complains that during Bluetooth calls, the person at the other end has trouble hearing the speaker in the vehicle. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.

Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty.

The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle.

Sound system ?pops? and loses audio for a few seconds. If the sound does not return on its own, or if it is accompanied by relevant DTCs in the vehicle, another issue may be present. Verify the root cause before proceeding with this bulletin. This bulletin only applies to vehicles with MMI Basic (PR Number 8DS). Continual improvements to MMI software provides solutions to issues experienced in the field.

During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle.

The Bluetooth telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present.

The customer complains about the picture quality of rearview backup camera image in the MMI screen. The picture is fuzzy or distorted. The picture looks too bright, too dark, or opaque in certain areas of the image. The colors of the objects in the image are incorrect or slightly off. The guidelines used for parking are fuzzy, distorted, or pixelated when compared with the guidelines displayed on another vehicle?s MMI.

The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.

Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".

*PE

repair is not needed.

wheel isn't heating evenly.

maneuvered.

outside influence is not covered under warranty.

outside influence is not covered under warranty. 2008-2020 A3, 2015-2020 A3 Cabrio, 2005-2016 A3 Sportback, 2005-2020 A4, 2010-2020 A4 allroad, 2005-2012 A4 Avant, 2005-2009 A4 Cabrio, 2010-2020 A5 Cabrio, 2008-2020 A5 Coupe, 2018-2020 A5 Sportback, 2005-2020 A6, 2005-2011 A6 Avant, 2008-2020 A7, 2005-2020 A8, 2008-2019 e-tron, 2019-2020 e-tron quattro, 2015-2020 Q3, 2009-2020 Q5, 2007-2020 Q7, 2019-2020 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2020 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2020 S5 Cabrio, 2008-2020 S5 Coupe, 2018-2020 S5 Sportback, 2007-2020 S6, 2008-2020 S7, 2007-2009 S8, 2018-2020 SQ5, 2004-2020 TT Coupe, 2004-2020 TT Roadster, 2012 TT/RS Coupe

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid.

Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.

Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned.

The customer may report that the Easy Entry function of the power adjustable steering column intermittently does not work.

Customer states the vertical adjustment of the steering column does not work or works intermittently. Concern may or may not be duplicated. Software issues causing sporadic failure of the power steering column vertical adjustment.

Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned.

Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.

The customer may report that the Easy Entry function of the power adjustable steering column intermittently does not work.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.

Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration.

Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic.

Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship.

Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period.

2,907 Audi owners in the State of Massachusetts on March 13, 2023.

Audi owners in the State of New Mexico on March 13, 2023.

Audi owners in the State of Colorado on February 13, 2023.

Audi owners in the State of New York on October 17, 2022.

notices to approximately 1,121 Audi owners in the state of South Carolina on September 19, 2022.

Audi owners in the State of Virginia on July 21, 2022.

approximately 939 Audi owners in the State of Alabama on March 23, 2022.

to approximately 4,943 Audi owners in the state of Pennsylvania on January 24, 2022.

notices to approximately 1,290 Audi owners in the state of South Carolina on January 24, 2022.

owners in the State of Idaho on August 30, 2021.

Audi owners in the State of New York on June 21, 2021.

Audi owners in the State of Texas on May 17, 2021.

(airbag/seatbelts, accidents, fire and overheat damage).

approximately 3,000 Audi owners in the State of Michigan on August 10, 2020.

approximately 370 Audi owners in the State of Texas on July 28, 2020.

Audi owners in the State of Tennessee on July 7, 2020.

in the State of Florida on June 26, 2020.

45 Audi owners in the State of California on June 22, 2020.

Audi owners in the State of Nebraska on March 23, 2020.

owners in the State of Ohio on February 10, 2020.

Audi owners in the State of Georgia on January 24, 2020.

approximately 1,800 Audi owners in the state of South Carolina on January 20, 2020.

approximately 27,300 Audi owners in the state of California on January 14, 2020.

of Neighborhoods, Audi will be sending Takata airbag recall reminder notices to approximately 2,300 Audi owners in the state of Texas on November 4, 2019.

Audi owners in the state of Arkansas on November 19 2019.

owners in the State of Pennsylvania on November 18, 2019.

2005 A4 Avant, S4 Avant, 2006 A4 Avant, A6 Avant, S4 Avant, 2007 A4 Avant, A6 Avant, S4 Avant, S4 Cabriolet, 2008 A4 Avant, A6 Avant, RS4 Cabriolet, S4 Avant, S4 Cabriolet, 2009 A6 Avant, 2010 A6 Avant, 2011 A6 Avant, 2016 TT Roadster, 2017 R8 Spyder, TT Roadster.

(airbag/seatbelts, accidents, fire and overheat damage.

Audi owners in the State of Minnesota on September 16, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3, 2016 TT Coupe, TT Roadster, 2017 R8 Coupe, R8 Spyder, TT Coupe, TT Roadster

Audi owners in the State of California on August 5, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3

4,500 Audi owners in the State of North Carolina on August 19, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3, 2016 TT Coupe, TT Roadster, 2017 R8 Coupe, R8 Spyder, TT Coupe, TT Roadster

Audi owners in the State of Virginia on August 12, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3, 2016 TT Coupe, TT Roadster, 2017 R8 Coupe, R8 Spyder, TT Coupe, TT Roadster

reminder notices to approximately 1,476 Audi owner in the state of Kentucky on July 15, 2019. 2005 A4 Avant, A4 Sedan, A6 Sedan, S4 Avant, S4 Sedan, 2006 A3, A4 Avant, A4 Sedan, A6 Avant, A6 Sedan, S4 Avant, S4 Sedan, 2007 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2008 A3, A4 Avant, A4 Cabriolet, A4 Sedan, A6 Avant, A6 Sedan, RS4 Cabriolet, RS4 Sedan, S4 Avant, S4 Cabriolet, S4 Sedan, S6 Sedan, 2009 A3, A4 Cabriolet, A6 Avant, A6 Sedan, Q5, S4 Cabriolet, S6 Sedan, 2010 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2011 A3, A5 Cabriolet, A6 Avant, A6 Sedan, Q5, S5 Cabriolet, S6 Sedan, 2012 A3, A5 Cabriolet, Q5, S5 Cabriolet, 2013 A3, 2016 TT Coupe, TT Roadster, 2017 R8 Coupe, R8 Spyder, TT Coupe, TT Roadster

(airbag/seatbelts, accidents, fire and overheat damage). 2008-2021A3, 2015-2021A3 Cabrio, 2005-2016 A3 Sportback, 1999-2021 A4, 2010-2021 A4 allroad, 1999-2012 A4 Avant, 2003-2009 A4 Cabrio, 2010-2021 A5 Cabrio, 2008-2021 A5 Coupe, 2018-2021 A5 Sportback, 1999-2021A6, 1999-2011A6 Avant, 2008-2020 A7, 1999-2021 A8, 2008-2019 e-tron, 2019-2021 e-tron quattro, 2015-2021 Q3, 2009-2021 Q5, 2007-2021 Q7, 2019 Q8, 2008-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2007-2008 RS4, 2008 RS4 Cabrio, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2004-2012 S4, 2004-2009 S4 Cabrio, 2010-2021 S5 Cabrio, 2008-2021 S5 Coupe, 2018-2021 S5 Sportback, 2007-2021 S6, 2008-2020 S7, 2007-2009 S8, 2018-2021 SQ5, 2000-2021 TT Coupe, 2001-2021 TT Roadster, 2012 TT/RS Coupe

After this date, Takata allocations will be based on the previous week?s paid claim volume. It is CRITICAL that claims are submitted in a timely fashion in order to receive an appropriate volume of additional parts to support demand.

MODELS A4, S4, A5, S5, Q5, TT, TTS, A3, PA , C6, A6 PA, D4, A8,C7 A7. *PE

(crawling when pulling away or briefly before standstill).

temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations. Dirt build-up, exposure to sand, long standing times, and road salt or similar, can also promote wear as well as cause scoring marks on the brake discs. The driving style of the driver also influences the wear of the brake system. An overly-aggressive driving style, which results in frequent sharp braking, can lead to more wear (particularly of the brake pads). A gentle driving style can result in very light brake applications. If the brakes are always applied with little pressure, a rust film and other airborne particles may settle on the brake discs and pads. Firm brake operations can help clean off such build-up from the brakes.

headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, and/or third brake light lens.

Customers may describe these noises as a squeal, squeak, grinding, groaning, thumping, or creaking.

If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated.

Customer complains of brake squeal.

DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools.

Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.

Oil appears on one or several shock absorbers.

Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines.

This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires.

Oil appears on one or several shock absorbers. Oil may appear on a shock absorber. As a result of a leak because the shock absorber is damaged. As a result of residue from when the shock was filled during production, or of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal.

Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens.

GUNS/WRENCHES NOT APPROVED FOR USAGE ON WHEEL BOLTS BY MANUFACTURER, THAT CAN CAUSE DAMAGE TO BRAKE, STEERING WHEEL, HUB. MODEL 1995-2014 ALL. *PE

*JS

ARE DAMAGED, PREVENTING PROPER ANALYSIS. *PE

Avant, A4 Cabriolet, S4 Cabriolet, A5 Cabriolet, S5 Cabriolet, A6 Avant, A6 Sedan, Q5, R8 Coupe, R8 Spyder, RS4 Cabriolet, RS4 Sedan, S6 Sedan, S6 Sedan, TT Coupe, and TT Roadster vehicles

will resume scheduling part pick-up from dealerships and service centers.

This document also applies to the 2007-2008 S4 Cabriolet, 2005-2008 A4 Avant, 2005-2008 S4 Avant, 2006-2011 A6 Avant, 2008 RS4, 2016-2017 TT Roadster and 2017 R8 Spyder.

required" message.

CD or DVD disks do not automatically change from one to the next in the external CD or DVD changer.

This TSB contains information on technician preparation when calling the Audi Technical Assistance Center

Oil filter cartridge requires replacement.

VIN plate and/or B-Pillar Safety Certification label requires replacement.

MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage greater than 20,000 miles.

Technician preparation when calling the Audi Technical Assistance Center (TAC).

Leather upholstery is dirty or stained.

Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options.

service.

REQUIRED" MESSAGE.

REQUIRED" MESSAGE.

APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM

APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM

APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN AND WARRANTY INFORMATION. *RM

APOLOGY LETTER ABOUT THE WATER PUMP CAMPAIGN. *RM

UNDER CERTAIN CONDITIONS THE COOLANT PUMP MAY LEAK. *RM

decomissioned).

software update for any TSB or Update.

software update for any TSB or Update.

2016-2020 A3, 2016-2020 A3 Cabrio, 2016 A3 Sportback, 2016-2020 A4, 2016-2020 A4 allroad, 2016-2012 A4 Avant, 2016-2020 A5 Cabrio, 2016-2020 A5 Coupe, 2018-2020 A5 Sportback, 2016-2020 A6, 2016-2020 A7, 2016-2020 A8, 2016-2020 e-tron, 2019-2020 e-tron quattro, 2016-2020 Q3, 2016-2020 Q5, 2016-2020 Q7, 2016-2020 Q8, 2016-2020 R8 Coupe, 2016-2020 R8 Spyder, 2017-2019 RS3, 2016-2020 RS5, 2016-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2016-2020 S5 Cabrio, 2016-2020 S5 Coupe, 2018-2020 S5 Sportback, 2016-2020 S6, 2016-2020 S7, 2018-2021 SQ5, 2016-2020 TT Coupe, 2016-2020 TT Roadster

This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.

DETAILING THE GENERAL PROCESS FOR CARRYING OUT A SOFTWARE VERSION MANAGEMENT (SVM) SOFTWARE UPDATE FOR ANY TSB OR REQUIRED VEHICLE UPDATE (RVU). TROUBLESHOOTING INFORMATION IS INCLUDED. *PE

State of Minnesota.

State of Minnesota.

conditions.

Media files can now be viewed on any smartphone or tablet.

conditions.

Media files can now be viewed on any smartphone or tablet.

conditions.

Media files can now be viewed on any smartphone or tablet.

The guard minimizes the likelihood that fuel other than ultra-low sulfur diesel will be put into the vehicle. The misfueling guard is designed to remain in a locked position when a nozzle with a diameter typically suited for non-diesel fuels (approximately 13/16?, or 20.6mm) is inserted, to prevent further insertion of the nozzle into the filler neck. A nozzle with a larger diameter typically suited for diesel fuel (approximately 15/16?, or 23.8mm) will unlock the misfueling guard when inserted, allowing the nozzle to be further inserted into the filler neck.

some issues.

If the effectiveness of a catalyst is reduced, this may result in an increase in tailpipe emissions and the vehicle could fail to pass an emissions inspection. Updated exhaust clamp part number to reference ETKA

If the effectiveness of a catalyst is reduced, this may result in an increase in tailpipe emissions and the vehicle could fail to pass an emissions inspection. Launch repair availability for A8 (criteria 4E) and A6 (criteria 4F).

If the effectiveness of a catalyst is reduced, this may result in an increase in tailpipe emissions and the vehicle could fail to pass an emissions inspection. Updated exhaust clamp part number for A6 and A8 models

If the effectiveness of a catalyst is reduced, this may result in an increase in tailpipe emissions and the vehicle could fail to pass an emissions inspection. ? Added repair availability for A8 (criteria 4E) and A6 (criteria 4F). ? Updated claiming instructions. ? Note added to repair instructions regarding consequential damage.

If the effectiveness of a catalyst is reduced, this may result in an increase in tailpipe emissions and the vehicle could fail to pass an emissions inspection.

If the effectiveness of a catalyst is reduced, this may result in an increase in tailpipe emissions and the vehicle could fail to pass an emissions inspection.

Media files can now be viewed on any smartphone or tablet. Audi of America has started to host its TSB videos outside of ElsaPro. Doing so provides higher-quality videos, more reliable access to the videos, and the ability to view the videos on different devices.

The iPod or the USB memory stick is not recognized or the iPod is not charged when either unit is connected to the Audi music interface (AMI). MMI3G or a Symphony/Concert CAN radio system with separate AMI control unit in the glove box or armrest. MMI3G+ with integrated AMI in the MMI main unit.

Customer states that the vehicle cannot be refueled due to difficulty inserting the fuel pump nozzle into the filler neck. Customer may also state that the flap is stuck in a locked position and it cannot be moved with fingers.

The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel.

UNDER SPECIFIC CONDITIONS, THE EMISSIONS CONTROL SYSTEMS WARRANTY, FOR FUEL INJECTOR REPLACEMENT, HAS BEEN EXTENDED TO 10 YRS OR 120,000 MILES, WHICHEVER HAPPENS FIRST. MODEL 2009-2011. *PE

the concern.

concern.

of the concern.

The seal ring is not the cause of the leak.

The seal ring is not the cause of the leak.

The seal ring is not the cause of the leak.

The seal ring is not the cause of the leak.

2010-2021 A3, 2015-2021 A3 Cabrio, 2010-2016 A3 Sportback, 2010-2021 A4, 2010-2021 A4 allroad, 2010-2012 A4 Avant, 2010-2021 A5 Cabrio, 2010-2021 A5 Coupe, 2018-2021 A5 Sportback, 2010-2021 A6, 2010-2021 A7, 2010-2021 A8, 2010-2019 e-tron, 2015-2021 Q3, 2010-2021 Q5, 2010-2021 Q7, 2019-2021 Q8, 2010-2020 R8 Coupe, 2011-2020 R8 Spyder, 2017-2019 RS3, 2010-2021 RS5, 2010-2020 RS5 Cabrio, 2016-2018 RS6, 2016-2018 RS7, 2010-2012 S4, 2010-2021 S5 Cabrio, 2010-2021 S5 Coupe, 2018-2021 S5 Sportback, 2010-2021 S6, 2010-2020 S7, 2010-2021 SQ5, 2010-2021 TT Coupe, 2010-2021 TT Roadster

a ODIS GFF test plan.

Any replacement of A/C compressors must include an ODIS GFF test plan confirming a malfunction of the A/C system with documentation of the recovered refrigerant volume.

The A/C Compressor has been diagnosed as faulty and will be replaced under warranty. When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.

When performing replacement of an A/C Compressor under warranty, the amount of refrigerant and oil recovered must be documented.

Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated.

There is an unpleasant, musty odor coming from the heating and ventilation system. The odor usually occurs when the vehicle has been sitting unused for five hours or more. The odor usually occurs within 20 to 60 seconds after the vehicle is started. Condensation, which is a normal condition in all A/C systems, can cause a musty odor.

taillights.

submissions.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

S4 Cabriolet, 2008 RS4 Cabriolet, 2010-2021 A4 allroad, 2018-2021 A5 Sportback, 2010-2012, 2018-2021 RS5 Cabriolet, 2018-2021 S5 Sportback, 2004-2006 A7, 2004-2011 S7, 2021 RS6 Avant, 2004-2006 S8

14s.

The process of draining oil through the drain plug is not always tidy. When oil is drained through the drain plug, the oil might spill on components around the oil pan area. If it is not properly cleaned up, this spilled oil could drip after the procedure is complete, causing unnecessary customer complaints.

The CD and DVD changer have different operating concepts. MMI3G: Disks in the CD changer are always automatically changed from one to the next. MMI3G+ (with Audi connect): Disks in the CD changer are automatically changed from one to the next, but this operation is disabled when the Repeat option is turned on in the Media Settings menu. By default (MMI factory default setting) the repeat option is set to ? Off?. DVD changer (A8 only): Disks in the DVD changer can only be changed manually.

Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet.

MODELS A8, A6 AND AUDI Q7 (2008-13). *PE

LED CONTACTS OF THE DAYTIME RUNNING LIGHT ON VEHICLES WITH XENON HEADLAMPS ARE AFFECTED DUE TO OXIDATION. MODIFIED HEADLIGHTS. REPLACE THE AFFECTED HEADLIGHT. *PE

DAYTIME RUNNING LIGHTS DO NOT WORK ON VEHICLES WITH XENON HEADLIGHTS. THE THUMB WHEEL OR OPTION FOR DAYTIME RUNNING LIGHTS IS TURNED OFF BY MISTAKE. *PE

LED CONTACTS OF THE DAYTIME RUNNING LIGHT ON VEHICLES WITH XENON HEADLAMPS ARE AFFECTED DUE TO OXIDATION. MODIFIED HEAD LIGHTS. REPLACE THE AFFECTED HEADLIGHT. *PE

dipped beam is switched on.

the Mirror Server.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield.

2010 AUDI A6. *RM

The sunglass holder in the dome light assembly will not latch closed or is stuck closed. The condition may be intermittent. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.

Clicking or clacking noise when maneuvering or parking. Normal driving dynamics may cause microscopic movements between the wheel bearing and wheel bearing housing.

The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.

2015-2020 A3 Cabriolet, 2016-2018 A3 Sportback, 2008-2009 S4 Cabriolet, 2008 and 2010 RS4 Cabriolet, 2018-2020 A5 Sportback, 2010-2012 and 2018-2020 RS5 Cabriolet, 2018-2020 S5 Sportback, 2008 A7, 2008-2011 S7

Wheel bolt requires torque adjustment.

Wheel bolt requires torque adjustment. Torque sticks, torque extension bars, and impact guns/wrenches are not approved by Audi of America, Inc., and should not be used to apply torque to wheel bolts. Always use a calibrated torque wrench to attain the correct wheel bolt torque and follow the proper wheel tightening procedure as outlined in Elsa. Proper use of a calibrated torque wrench ensures that all wheel bolts are tightened equally and reduces the chances of repeat repairs. Using methods other than a calibrated torque wrench to attain correct wheel bolt torque may lead to problems.

Automatic transmission fluid is leaking at the sump pan gasket.

This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.

Customer may report that downshifts are not smooth when the vehicle is slowing down. Update to improved software introduced after production will reduce complaints with shifting characteristics. Improved viscosity of ATF lessens clutch grab during clutch activation.

The customer may report flickering of the dash insert lighting, of the A/C control panel lighting, or of the inside light. The condition occurs when the accelerator is pressed while the vehicle is in P or N, or when the vehicle is shifted down when moving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off when the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly-increased voltage, causing the lights to flicker.

Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted.

The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle.

Automatic transmission fluid is leaking at the sump pan gasket. As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak.

ADAPT TO NEW COMPONENTS WITH GRADUAL MOVING OF CLUTCH LININGS IN MOST DIVERSE LOAD CONDITIONS. MODELS 2004-14, A3, TT, Q7, A4, A5, A6, A7, A8, Q5, S4, S5, S6, S7, RS5. *PE

CERTAIN MODELS, CAMERA IMAGE CAN BE RE=ACTIVATED. MODEL YEARS 2008-2013. *PE

*PE

*RM