2018 Alfa Romeo Stelvio TSBs

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

only replace the EVAPORATIVE SYSTEM INTEGRITY MODULE DETECTOR.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

P0304 after performing the PCM software update process for Customer Satisfaction Notification (CSN) W05.

washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.

radio to software level to MV 090.000.061The customer should be informed that after the reprogram, the radio will need to have the phones paired to theEntertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the Owner Handbook of the infotainment module. Some customers may experience one or more of the following: Radio may reboot while driving.Software update will help correct existing issue. Radio stays on if you exit the vehicle during a phone call. When the vehicle is remote started the radio will turn on at the previously set volume level.

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

P0304 after performing the PCM software update process for Customer Satisfaction Notification (CSN) W05.

radio to software level to MV 090.000.061The customer should be informed that after the reprogram, the radio will need to have the phones paired to theEntertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the Owner Handbook of the infotainment module. Some customers may experience one or more of the following: Radio may reboot while driving.Software update will help correct existing issue. Radio stays on if you exit the vehicle during a phone call. When the vehicle is remote started the radio will turn on at the previously set volume level.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Monitor Module after flashing PCM for Customer Satisfaction Notification (CSN) W05.

radio to software level MV-002.010.041.The customer should be informed that after the reprogram, the radio will need to have the phones paired to the Entertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in theOwner Handbook of the infotainment module. Some customers may experience one or more of the following:Voice commands not recognized, especially in SiriusXM. Can't select certain character in navigation, character grayed out. Radio may reboot while driving. Tweeter noise during audio streaming. Ipod Nano not recognized. Voice recognition does not work when setting an address in Spanish. In addition, the following improvements are included:Stability improvements, to help prevent the radios from rebooting and freezing. Preset management improvements, for better usability. Additional phone compatibility improvements on phones not tested in the past.

radio to software level MV-002.010.041.The customer should be informed that after the reprogram, the radio will need to have the phones paired to the Entertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in theOwner Handbook of the infotainment module. Some customers may experience one or more of the following:Voice commands not recognized, especially in SiriusXM. Can?t select certain character in navigation, character grayed out. Radio may reboot while driving. Tweeter noise during audio streaming. Ipod Nano not recognized. Voice recognition does not work when setting an address in Spanish. In addition, the following improvements are included:Stability improvements, to help prevent the radios from rebooting and freezing. Preset management improvements, for better usability. Additional phone compatibility improvements on phones not tested in the past.

radio to software level MV-002.010.041.The customer should be informed that after the reprogram, the radio will need to have the phones paired to the Entertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in theOwner Handbook of the infotainment module. Some customers may experience one or more of the following:Voice commands not recognized, especially in SiriusXM. Can?t select certain character in navigation, character grayed out. Radio may reboot while driving. Tweeter noise during audio streaming. Ipod Nano not recognized. Voice recognition does not work when setting an address in Spanish. In addition, the following improvements are included:Stability improvements, to help prevent the radios from rebooting and freezing. Preset management improvements, for better usability. Additional phone compatibility improvements on phones not tested in the past.

radio to software level MV 085.000.046. The customer should be informed that after the reprogram, the radio will need to have the phones paired to the Entertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the OwnerHandbook of the infotainment module. Some customers may experience one or more of the following:Radio may reboot while driving. Radio stays on if you exit the vehicle during a phone call. When the vehicle is remote started the radio will turn on at the previously set volume level.

If no response in 15 minutes, proceed with repair.

Use the wiTECH 2.0 and inspect the radio part number and serial number under the Radio/ECU Details tab. Please verify that the radio part number and/or serial number is not "FFFF". If either field shows "FFFF", please contact Mike Wielgat at 248-576-6696 or Rohan Negandhi at 248-421-9608 If no response in 15 minutes, proceed with repair.

washer fluid bottle is full, please perform this inspection: Check if float sensor is rotated off location from the bottle anti-rotation features that surround the SENSOR. Check to determine if the issue has been resolved. Continue with repair if necessary. Please contact Chris Koch at cell (248) 248-622-6417 if you have questions or need additional information.

the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles) This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter.

845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.

the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles). This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter."

installed in the vehicle.

Engine misfires.

The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).

Engine misfires.

Engine misfires.

Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.

The o-ring is serviced separately and complete turbo replacement may not be necessary.

installed in the vehicle.

Start Stop Unavailable, ACC Unavailable Service Required Messages. C1452-86 Engine Torque DASM- Signal Invalid

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).

softwareand replacing the oil vapor recovery tube. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) have been set:P032D-00 - Knock Sensor 3 Circuit High. P008A-00 - Low Pressure Fuel System Pressure - Too Low. P034C-00 - Ion Sense System Performance. P051B-00 - Crankcase Pressure Sensor Circuit Range/Performance.

The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).

softwareand replacing the oil vapor recovery tube. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or moreof the following Diagnostic Trouble Codes (DTCs) have been set:P032D-00 - Knock Sensor 3 Circuit High. P008A-00 - Low Pressure Fuel System Pressure - Too Low. P034C-00 - Ion Sense System Performance. P051B-00 - Crankcase Pressure Sensor Circuit Range/Performance.

Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.

The o-ring is serviced separately and complete turbo replacement may not be necessary.

Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.

The o-ring is serviced separately and complete turbo replacement may not be necessary.

The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).

also known as a PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set:P0106-00 - Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance. P013A-00 - O2 Sensor Slow Response Rich To Lean Bank 1 Sensor 2. P015A-00 - O2 Sensor Delayed Response Rich To Lean Bank 1 Sensor 1. P1CEA-00 - Boost Side EVAP Purge System Performance. P0096-00 - Intake Air Temperature Sensor 2 Circuit Range-Performance. P04DB-00 - Crankcase Ventilation System Disconnected. P024A-00 - Charge Air Cooler Bypass Control "A" Range/Performance. P2097-00 - Post Catalyst Fuel Trim System Rich. P2B2F-00 - Fan 1 Performance/Stuck Off. P24D6-00 - EVAP System Pressure Sensor/Switch "B" Circuit Range/Performance. P01BA-00 - Engine Oil Temperature Sensor "B" Range/Performance. P026E-00 - Charge Air Cooler Coolant Pump Performance. P164E-00 - A/C Clutch Relay Control Range/Performance. P0191-00 - Fuel Rail Pressure Sensor "A" Circuit Range/Performance. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U1008-00 - LIN 1 BUS. Customers may experience one or more of the following:Not passing vehicle certification during state inspections if performed after a system reset. Driveability issues. Engine misfire when cold. In addition, the following improvements are also available:Turbo coolant pump after run duration and on-off strategy update, to improve turbo O-ring durability. Message ?S&S Not Available? will be changed to ?Hood Open?. Improved idle stability during tip in tip out. Improved idle stability during an Engine Start Stop (ESS) event.

also known as a PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set:P0106-00 - Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance. P013A-00 - O2 Sensor Slow Response Rich To Lean Bank 1 Sensor 2. P015A-00 - O2 Sensor Delayed Response Rich To Lean Bank 1 Sensor 1. P1CEA-00 - Boost Side EVAP Purge System Performance. P0096-00 - Intake Air Temperature Sensor 2 Circuit Range-Performance. P04DB-00 - Crankcase Ventilation System Disconnected. P024A-00 - Charge Air Cooler Bypass Control "A" Range/Performance. P2097-00 - Post Catalyst Fuel Trim System Rich. P2B2F-00 - Fan 1 Performance/Stuck Off. P24D6-00 - EVAP System Pressure Sensor/Switch "B" Circuit Range/Performance. P01BA-00 - Engine Oil Temperature Sensor "B" Range/Performance. P026E-00 - Charge Air Cooler Coolant Pump Performance. P164E-00 - A/C Clutch Relay Control Range/Performance. P0191-00 - Fuel Rail Pressure Sensor "A" Circuit Range/Performance. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U1008-00 - LIN 1 BUS. Customers may experience one or more of the following:Not passing vehicle certification during state inspections if performed after a system reset. Driveability issues. Engine misfire when cold. In addition, the following improvements are also available:Turbo coolant pump after run duration and on-off strategy update, to improve turbo O-ring durability. Message ?S&S Not Available? will be changed to ?Hood Open?. Improved idle stability during tip in tip out. Improved idle stability during an Engine Start Stop (ESS) event.

also known as a PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set:P0106-00 - Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance. P013A-00 - O2 Sensor Slow Response Rich To Lean Bank 1 Sensor 2. P015A-00 - O2 Sensor Delayed Response Rich To Lean Bank 1 Sensor 1. P1CEA-00 - Boost Side EVAP Purge System Performance. P0096-00 - Intake Air Temperature Sensor 2 Circuit Range-Performance. P04DB-00 - Crankcase Ventilation System Disconnected. P024A-00 - Charge Air Cooler Bypass Control "A" Range/Performance. P2097-00 - Post Catalyst Fuel Trim System Rich. P2B2F-00 - Fan 1 Performance/Stuck Off. P24D6-00 - EVAP System Pressure Sensor/Switch "B" Circuit Range/Performance. P01BA-00 - Engine Oil Temperature Sensor "B" Range/Performance. P026E-00 - Charge Air Cooler Coolant Pump Performance. P164E-00 - A/C Clutch Relay Control Range/Performance. P0191-00 - Fuel Rail Pressure Sensor "A" Circuit Range/Performance. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U1008-00 - LIN 1 BUS. Customers may experience one or more of the following:Not passing vehicle certification during state inspections if performed after a system reset. Driveability issues. Engine misfire when cold. In addition, the following improvements are also available:Turbo coolant pump after run duration and on-off strategy update, to improve turbo O-ring durability. Message ?S&S Not Available? will be changed to ?Hood Open?. Improved idle stability during tip in tip out. Improved idle stability during an Engine Start Stop (ESS) event.

This will allow service technicians to repair the root cause without over repairing the system. Replace only the part deemed failed by the diagnostics performed. Individual parts include: - Compressor - Valve block - Individual hoses - Temp sensor - Shield - Air line clips NOTE: in most situations when a new compressor is needed, the compressor as a separate part is the correct repair, and the assembly would not be required.

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

awareness regarding the use of aftermarket parts.

structural repair parts usage.

Detected Message

awareness regarding the use of aftermarket parts.

(Connecticut, Delaware, Massachusetts, Maine, New Hampshire, New Jersey, New York, Pennsylvania, Virginia, and Washington dc), and some ladco states (Illinois, Michigan, and Ohio). Mopar offers an alternative product (82213192) which is a water based product approved for sale in the aforementioned states.~ ~ Please inform the customer & your prep dept that spraying excessive amounts of the fabric protector on load floors will result in the breaking down of the adhesive (glue) that is used to create the bond between the fabric (carpet) and the load floor. This will apply to any vehicles equipped with rear load floors such as WK, WD, PM, MK, KA, KK. The carpet will appear to be loose, wrinkly, or bunch up~

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

industry awareness regarding the recommended usage of Authentic Mopar Glass.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

Only replace the door hinge with the integral check device. Do not replace the simple hinge if it is not damaged it is not the source of the noise. Replacing it unnecessary and is an over-repair.

B)

module with the latest available software. The following enhancement is included with this update:Improved brake pedal feel.

Rev A

industry awareness regarding the use of recycled or salvage parts.

Library for specifications so a suitable alternative can be used

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.

Call Steve Rice at cell (248) 867-0061 before replacing the pressure transducer. If no response in 15 minutes, please proceed with repair.