2023 Alfa Romeo Giulia TSBs

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

illumination and the vehicle must exhibit the following Diagnostic Trouble Code (DTC): P0606 - Control Module Processor. Customers may also experience the following: Vehicle goes into limp-in mode REPAIR SUMMARY: **This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.** "

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

illumination and the vehicle must exhibit the following Diagnostic Trouble Code (DTC): P0606 - Control Module Processor. Customers may also experience the following: Vehicle goes into limp-in mode This bulletin involves reprogramming the PCM with the latest available software"

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

only replace the EVAPORATIVE SYSTEM INTEGRITY MODULE DETECTOR.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

vehicle data on customer's mobile app. Connected Services maintenance popup displayed on the radio screen. Connected Services battery maintenance popup displayed on the radio screen. This bulletin involves reprogramming the TBM with the latest available software."

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P1CEA-00 - Boost Side Evap Purge System Performance. This bulletin involves reprogramming the PCM with the latest available software.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Short Circuit To Ground Or Open Circuit DTC Set For All Sensor In the Park Assist Module (PAM)

Short Circuit To Ground Or Open Circuit DTC Set For All Sensor In the Park Assist Module (PAM)

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? **P1CEA-00 - Boost Side EVAP Purge System Performance.** ? P2300-00 - Ignition Coil A Primary Control Circuit Low. ? P2303-00 - Ignition Coil B Primary Control Circuit Low. ? P2306-00 - Ignition Coil C Primary Control Circuit Low. ? P2309-00 - Ignition Coil D Primary Control Circuit Low. ? P1CEA-00 - Boost Side EVAP Purge System Performance. This bulletin involves reprogramming the PCM with the latest available software.

Redacted Content for further assistance. If no response in 15 minutes, proceed with repair.

Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? **P2300-00 - Ignition Coil 9A9 Primary Control Circuit Low. ? P2303-00 - Ignition Coil 9B9 Primary Control Circuit Low. ? P2306-00 - Ignition Coil 9C9 Primary Control Circuit Low. ? P2309-00 - Ignition Coil 9D9 Primary Control Circuit Low.** ? P1CEA-00 - Boost Side Evap Purge System Performance. This bulletin involves reprogramming the PCM with the latest available software.

Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set: ? P1CEA-00 - Boost Side Evap Purge System Performance. This bulletin involves reprogramming the PCM with the latest available software.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

chatter/streak/jump/skip/smear or make noise while traveling across the windshield. . No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

chatter/streak/jump/skip/smear or make noise while traveling across the windshield.

Cluster (IPC)

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

Cluster (IPC)

NOTE: Mostly heard when driving on bumpy roads. This bulletin involves applying felt tape between the front frame of the instrument panel cluster and the dashboard lid.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles) This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter.

845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.

Once the claimed fault is confirmed, check the severity of the leak and replace the timing cover sealant, if necessary, according to the Repair Procedure."

Once the claimed fault is confirmed, check the severity of the leak and replace the timing cover sealant, if necessary, according to the Repair Procedure."

Once the claimed fault is confirmed, check the severity of the leak and replace the timing cover sealant, if necessary, according to the Repair Procedure. "

the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles). This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter."

this is normal and not a defect.

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

continues to reboot after a Map Update (MOTA). ? Navigation regularly cuts out and back on again. ? Radio switches to navigation without customer's input. This bulletin involves updating the Navigation maps via USB.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order a "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

B)

System - Light on instrumental panel control cluster Adaptive Cruise Control (ACC) System - Light on instrumental panel We inform you that if the collision radar warning light is temporarily on and the temporary inhibition of the FCW (Forward Collision Warning) and the ACC (Adaptive Cruise Control) are both temporarily inhibited, the vehicle is conforming. If conditions are such that the radar cannot detect obstacles correctly, the system is temporarily deactivated and a dedicated message is displayed on IPC (Instrument Panel Control Cluster). Temporary deactivation is caused by automatic radar learning under particular conditions:  Change in vehicle weight distributed unevenly.  Change in vehicle geometry.  Roads with limited presence of radar references (guard rails, road signs, other vehicles on the carriage way, etc.).  Severe weather conditions (snow fall or heavy rain).  Highly reflective conditions (e.g., tunnels with reflective tiles, or ice or snow, or sites with road work).  Obstruction of radar due to presence of mud, dirt or ice on bumper or radar surface and/or cover. Please note that the problem solves itself and one or more of the following DTCs may be stored: ACC C1417-78: Horizontal misalignment of sensor - Incorrect alignment or adjustment ACC C1418-78: Vertical misalignment of sensor - Incorrect alignment or adjustment ACC C1409-97: Blinded radar sensor - Obstructed or blocked component This is not a fault but rather a message alerting the driver that the FCW and possibly ACC (if activated) functions are temporarily inhibited. Please be advised that if the customer complains of temporary or sporadic illumination of the anti-collision warning light with the AEB system subsequently returning to full functionality, the vehicle is conforming and no radar adjustment is required. If the message is displayed frequently, even in the absence of weather conditions such as snow, rain,mud, or other types of obstruction, check and clean the radar surface directly by manually removing the aesthetic cover plate."

Rev A

lamps (headlamps, fog lamps, grille lamps, logo lamps or signature lamps) assemblies are fogged with a light layer of condensation on the inside of the lenses*

"

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.